Müller-Mitteltal Zamenljivo Ohišje nakup rabljenega (275)

Stanje: novo, največja dovoljena obremenitev: 23.210 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, * T 3: * ABS zavorni sistem * Sistemska oprema za sprostitev vzmetnih cilindrov v sili * Bobnaste zavore * 3 x 11 t. BPW Eco osi * Parabolaste vzmeti * Mehanski izravnalnik osi zadaj * Stranska zaščita proti naletu * Zadnje vrtljive oporne noge na šasiji vozila * Mehansko nastavljivi opozorilni tablini paketi spredaj in zadaj * Spredaj zaprti plastični blatniki in zadaj ravne pocinkane jeklene zaščite proti pršenju, obe s ščitniki proti brizganju * Konturirani odsevni trakovi ob straneh in zadaj * Zložljiv pokrov orodjarne (vroče pocinkan) na rotacijski ploščadi * Orodjarna iz pocinkanega jekla približno 650 x 300 x 600 mm – črno prašno barvana – ob strani pod šasijo * 15-pinski električni priključek * LED osvetlitev 12 / 24 V * LED rotacijska luč (odstranljiva) zadaj * Vlečna škarja z vlečnim ušesom 40 mm in nastavitvijo višine preko vlečne vzmeti in napenjalnega vijačnika * Na vsaki strani po 4 žepi za pilote (brez pilotov) z istočasno možnostjo pritrjevanja * Paket za varno nalaganje (La-Si): 2 pritrdilni obroči (6,4 t) spredaj levo in desno na glavnem okviru rotacijske ploščadi * 5 parov UVV vrtljivih in spuščajočih se pritrdilnih obročkov * Nosilnost v vse smeri; v vogalih zunanjega okvirja do 13,4 t, sicer 10 t * 6 parov mehanskih zložljivih podaljškov za skupno širino 3 m (ne vključuje zadnje zaokrožitve) * Razširitveni podesti shranjeni v predalu pod tovorno površino * Odlagalna površina za roko bagra nad zadnjo osjo do končnega nosilca, dolga cca. 2100 mm (2 para stranskih pritrdilnih obročkov 6,4 t v odlagalni površini) * Hidravlične zložljive rampe (pribl. 4650 x 720 mm) z hidravlično nastavljivim vrhnjim delom in varnostnimi ventili, hidravlični stranski premik ramp * Hidravlični razdelilnik v prikolici (za hidravlično črpalko v tovornjaku z zmogljivostjo nad 40 l/min, največ do 140 l/min), dvocevna hidravlika * Nakladalna površina nad vrtljivim ležajem: pribl. 1960 x 2520 mm * Zadnja nakladalna površina: pribl. 6500 x 2520 mm (vklj. 860 mm naletne rampe) * Nakladalna višina obremenjeno pribl. 860 mm +/- 30 mm prilagoditev * Šasija, rotacijska ploščad, zložljivi podaljški, padajoče oporne noge zadaj in rampe toplotno pocinkane * Osi, vzmeti, vlečna škarja, zračni rezervoar itd. lakirani v črnem odtenku * Novo vozilo z garancijo proizvajalca * Pridržujemo si pravico do sprememb in vmesne prodaje * Na voljo takoj iz Egestorfa Hodpfx Asq Dyv Iepnsnp

Stanje: novo, največja dovoljena obremenitev: 20.500 kg, skupna masa: 27.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TR 27.0 Platform: * EBS (Electronic Braking System) * Emergency release system for spring-loaded brake cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lift and lowering device including RTR function * First axle liftable * Last axle is self-steering trailing axle with electro-pneumatic steering lock via reverse gear PIN (Steering lock for trailing axle activated from the tractor for maneuvering purposes—no truck-side installation required—wired to PIN 10 in the 15-pin connector, only for maneuvering and not for use on public roads) * SmartBoard control unit as infotool with pressure sensors for displaying total axle load * Tire pressure monitoring with readout in the truck via EBS signal, no truck-side installation required * Fixed center drawbar with 50 mm flange drawbar eye (loaded 900 mm, mm height adjustment at the head plate) * Mechanical landing gear at the front, mechanical swivel supports at the rear chassis * Hydraulic flow divider * Continuous side walls (without center stanchion) up to the drive-on slope * Folding rear stanchions * Steel rear wall slotted in before rear stanchions * Mechanically adjustable warning panel kit front and rear * Toolboxes made of galvanized steel sheet—black powder-coated—approx. 650 x 300 x 600 mm, right side * 15-pin power connector * LED tail lights * Removable LED rotating beacon incl. bracket and installation * 2 x LED reversing lights at vehicle rear (activated via reverse gear) * Flashing LED side marker lights * 60 mm larch/douglas fir wooden floor * 400 mm steel front wall slotted in * Perforated outer frame approx. 45° angled with provisions for mounting 3 t folding lashing rings * In each corner: 1 x 10 t lashing ring, plus 2 x 10 t and 3 x 6.3 t lashing rings on each side * Various holes for 1.2 t lashing points in front and rear crossmembers Hnodpfx Asr Dpzxjpnep * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm, mechanically adjustable sideways * 4-circuit hydraulic control block for potential retrofit of hydraulic ramp shifting * Chassis, drawbar, front wall, mechanical rear supports, and loading ramps hot-dip galvanized * Axles, air tanks, flange drawbar eye, and front landing gear painted in black * Hydraulic flow divider in the trailer (for hydraulic pump output in truck from over 40 l/min up to 120 l/min) * New vehicle with manufacturer warranty * Subject to error and prior sale * Available immediately ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 18.900 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA-Kombi 24.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes Hnedpjpk D Awjfx Apnsp ----Suspension: * Air suspension with manual lowering at the rear ----Axle: * 3 x 11 t Gigant axles * Centre axle liftable ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm towing eye & height adjustment ----Electrics / Lighting: * LED rear lights * 15-pin power connector * TPMS (Tire Pressure Monitoring System) ----General Attachments: * Toolbox made of powder-coated sheet steel (W: 1,000 mm x H: 300 mm x D: 450 mm) * Storage box for container nets made of galvanized sheet steel (W: 960 mm x H: 300 mm x D: 450 mm) * Side underrun protection * Plastic quarter mudguards with splash protection * Plastic rear bumper buffer * Mechanical drop-down supports at the rear ----Container / Low-bed platform: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm raised) to guide roll-off containers * Steel floor with roll grooves in the bogie area * When transporting roll-off containers, container length from 5,500 to 7,000 mm possible * Pneumatic 4-point container locking and mechanically insertable front stop angles in the running rails * Load securing certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. 10 m³ volume possible * Includes 8 repositionable skip stops for lateral centering of skips, front 4 skip stops fitted with pivoting stops ----Load securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning elements for positive and non-positive securing of skips * 4 cloverleaf lashing points on each side and 1 pair of 13.4 t UVV lashing rings at the front * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 ----Ramps: * Weld bead as anti-slip surfacing in the running area of the access slope * 1 pair of aluminium loading ramps (16 t / pair), 2,800 x 400 mm, suitable for rubber-tyred and tracked vehicles (lockable storage compartment accessible from the rear) ----Tyres: * Tyres: 235/75 R17.5 ----Ride height: * Ride height, loaded: approx. 1,003 mm ----Payload: * Payload: 18,900 kg ----Paintwork: * Reflective contour marking tape, side and rear * Axles, turntable, drawbar and air tank painted black * Hot-dip galvanized main frame ----Information: * Gross vehicle weight technically possible: 27,000 kg * New vehicle without initial registration with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available from approx. week 47/2026

Stanje: novo, največja dovoljena obremenitev: 10.360 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-ER 14.4: Hsdpfjpk D Dqjx Apnenp ----Brakes: * Electronic Brake System (EBS) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * Gigant axles ----Suspension: * Air suspension with lift and lower facility ----Drawbar / Flange Eye: * Drawbar height adjustable by approx. 300 mm * 40 mm flange drawbar eye ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System with in-cab display via EBS signal; no truck-side installation required) * LED lighting system * 15-pin power connector ----General Attachments: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding support legs at the rear * Plastic toolbox, front right, mounted outside on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * 50 mm softwood flooring * Provision for retrofitting 20" container locks at front and rear * Bolted bulkhead made of smooth sheet steel * Fold-down side walls, trapezoidal profile, with drop-side spring assists * Bolted, hot-dip galvanized rear stanchions ----Load Securing: * Outer frame with holes, approx. 45° angled, 2 t lashing capacity every 480 mm * Option to install 3 t recessed lashing rings every 600 mm * Each of the front and rear corners fitted with 1 x 6.3 t lashing ring * Various holes in front and rear cross members for 1.2 t lashing options ----Ramps: * 1 pair of aluminium loading ramps, approx. 3,310 x 400 mm (load capacity 8 t per pair), suitable for pneumatic and tracked vehicles; stowed at the rear in a compartment integrated below the deck in the chassis ----Paintwork: * Hot-dip galvanized chassis, drawbar, bulkhead, and rear wall * Vehicle fully hot-dip galvanized ----Information: * New vehicle with manufacturer’s warranty * Subject to error and prior sale ----Delivery Time: * Available immediately ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 13.600 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2026, * KA-TA-RT 18.0: ----Brake: * EBS (Electronic Braking System) * Emergency release for spring brake cylinders * Drum brakes ----Suspension: * Air suspension with lifting and lowering device, including Ride-Through-Release (RtR) valve and manual lowering function for loading ----Drawbar / Flanged Drawbar Eye: * Drawbar with positive-locking height adjustment * 50 mm flanged drawbar eye ----Electrics / Lighting: * 15-pin 24 V connector * LED tail lights 12 / 24 V fitted in underrun protection ----General Attachments: * Support winch at front * Fold-away rear support legs on the outside * Plastic toolbox approx. 750 x 350 x 300 mm, mounted on right side * Plastic quarter mudguards ----Tipping Body: * Steel pallet – 3-way tipper body made of high-tensile fine grain steel with high M-Strong side panels and reinforced 180 bar tipping cylinder Hodpfx Apsvin Ucsnjnp * Fixed front wall made of smooth sheet steel * Hardwood strip for excavator bucket screwed onto front wall * Continuous side panels – fold-down without center pillar, with sideboard spring-assist lifters and swinging function via manual central locking * Bolt-on rear stanchions * Combination steel swing doors at rear, 2-leaf, asymmetrically split, able to swing open 270° and lockable (not foldable), including additional swinging frame for automatic rear door opening when tipping; locking by galvanized rotating bar lock and central locking, deactivation function for automatic rear door opening when tipping backwards with opened swing doors * 4 mm steel floor plate * Two-step access on the left front * Rear ramp track for loading ramps ----Load Securing: * One 7 t lashing ring in each corner * Four 3 t lashing eyes recessed in the outer frame on each side ----Loading Ramps: * Recessed ramp compartment at rear of chassis * 1 pair aluminium loading ramps (10 t/pair), approx. 3,570 x 410 mm, suitable for rubber-tired and tracked vehicles ----Paintwork: * Chassis, drawbar, rear stanchions, front wall, tipping platform, underrun protection, and rear supports hot-dip galvanized * Sideboards painted in any desired RAL colour (excluding special or metallic paints), can be changed up to approx. 6 weeks before completion * Axles, air tanks, flanged drawbar eye, and front support winch painted in black ----Info: * --Load securing certificate according to EN 12642 XL? * Errors and intermediate sale reserved ----Delivery Time: * Available from approx. CW 45 / 2026

Stanje: novo, največja dovoljena obremenitev: 8.800 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.370 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-R 11.9: ----Brakes: * EBS brake system * Emergency release device for spring brake cylinders * Drum brakes, 2 x 5.5 t ----Axles: * Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar by 300 mm * 40 mm flange towing eye ----General Attachments: * Jost landing gear at the front * External folding supports at the rear * Plastic toolbox, front right outside on the front wall * Side underrun protection * Plastic quarter mudguards ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) Hnjdpfsl Th Ncex Apnep * LED lighting ----Loading Platform: * Platform length 5.37 m * 50 mm softwood floor * Bolted smooth sheet steel front wall * Fold-down side walls made of trapezoidal-profiled steel sheet with board lifting spring * Rear wall made of steel, insertable between the ramp holders for storage in front of the front wall when not in use * Rear stanchions bolted ----Load Securing: * Perforated outer frame, approx. 45-degree bent, with 2 t lashing capacity every 480 mm * Installation of 3 t recessed lashing rings every 600 mm possible * In each corner front and rear, 1 x 6.3 t lashing ring * Various holes in front and rear crossmembers for 1.2 t lashing options ----Ramps: * One-piece mechanical grating loading ramps with spring system for single-person operation, approx. 2,750 x 600 mm (collapsible to 20 mm) * Rear approach angle approx. 860 mm chassis ----Tyres: * Tyres 235/75 R 17.5 ----Wheelbase: * Wheelbase: 990 mm ----Paintwork: * Drawbar, front wall, tailgate, folding supports, loading ramps galvanized * Axles, springs, air tanks, 40 mm flange towing eye painted in black * Board walls painted in RAL2011 deep orange * Side panels available in other RAL colors at extra cost ----Information: * New vehicle with manufacturer warranty * Errors and prior sale excepted ----Delivery Time: * Immediately available ex works Egestorf

Stanje: novo, največja dovoljena obremenitev: 13.600 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2026, * KA-TA-RT 18.0: ----Braking System: * EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Suspension: Hnodpfx Apjvin T Senep * Air suspension with lifting and lowering system, including RtR valve and manual lowering for loading operations ----Drawbar / Flange Drawbar Eye: * Drawbar with positive-locking height adjustment * 50 mm flange drawbar eye ----Electrics / Lighting: * 15-pin 24 V connector * LED tail lights 12 / 24 V integrated in underrun protection ----General Attachments: * Landing gear at the front * Fold-out support legs at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * Plastic quarter mudguards ----Tipper Body: * Steel 3-way tipper body made of fine-grain steel with high M-Strong side walls and reinforced 180 bar tipping cylinder * Fixed front wall, smooth sheet steel * Hardwood pad for excavator bucket bolted to front wall * Continuous, folding drop sides without central stanchion, with sideboard spring assist and manual central locking system * Screwed-in rear stanchions * Combination steel swing doors, asymmetrical 2-leaf rear wall, can be swung and locked at 270°, not foldable, with additional swinging frame for automatic rear wall opening during tipping, locking via galvanized rotary bar lock and central locking system, deactivation function for automatic rear wall opening when tipping reverse with open swing doors * 4 mm steel floor plate * Two-step entry left front * Rear mounting rail for loading ramps ----Load Securing: * 1 x 7 t lashing ring in each corner * 4 x 3 t lashing rings recessed into the outer frame on each side ----Loading Ramps: * Integrally mounted ramp storage at the rear of the chassis * 1 pair of aluminum loading ramps (10 t / pair) approx. 3,570 x 410 mm, suitable for rubber-tired and tracked vehicles ----Paintwork: * Chassis, drawbar, rear stanchions, front wall, tipping platform, underrun protection, rear folding supports hot-dip galvanized * Sideboard paintwork in RAL custom color (with exceptions for special or metallic paintwork); can be changed up to approx. 6 weeks prior to delivery * Axles, air tanks, flange drawbar eye, front landing gear painted in black ----Information: * --Load securing certificate according to EN 12642 XL? * Subject to errors and prior sale ----Delivery Time: * Available from approx. CW 45 / 2026

Stanje: novo, največja dovoljena obremenitev: 8.780 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2024, * KA-TA-R 11.9 Masterline: ----Brakes: * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem equalization unit ----Drawbar / Flange Eye: * Height-adjustable hot-dip galvanized drawbar, adjustable by 300 mm, with 40 mm flange eye ----General Attachments: * Jost mechanical landing gear (front) * Two rear mechanical hot-dip galvanized fold-down supports * Tool box made of galvanized steel sheet, mounted right side * Plastic quarter mudguards ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin electrical connector * Bolted underride guard with LED tail lights ----Tipping Platform: * Net hooks on the sides and rear in the central locking mounts as well as 3 external on the front wall * Hot-dip galvanized chassis * Steel pallet 3-way tipper body, fully galvanized * Continuous, drop-side walls with spring-assisted board wall lifters, can be folded down—no center stanchions * Tailgate foldable and pendulum-mounted via manual central locking * Hot-dip galvanized bolted rear stanchion ----Load Securing: * 1 recessed and foldable 5 t lashing ring in each corner, as well as 4 recessed and foldable 3 t lashing rings on each side in the outer frame * 4 mm steel sheet floor, rear mount rail for ramps ----Ramps: * 1 pair aluminum loading ramps approx. 3,570 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment under the loading area at the rear, integrated into the chassis Hnedpfx Apspk D D Uenjp ----Tires: * 235/75 R 17.5 tires ----Paint Finish: * Axles, springs, air tanks, drawbar and landing gear painted in black * Vehicle is hot-dip galvanized ----Notes: * Reinforced body with load securing certificate according to EN 12642 XL * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery Time: * Available immediately from Egestorf on the A7

Stanje: rabljeno, največja dovoljena obremenitev: 31.000 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 07/2024, dolžina tovornega prostora: 9.290 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 950 mm, * PT 40.0 Profi ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 4 x 11 tonne Gigant axles ----Suspension: * Air suspension with lifting and lowering system and RtR valve ----Drawbar: * Drawbar with 50 mm towing eye and height adjustment ----Lighting / Electrical: * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power connector * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (activated via reverse gear) ----General Attachments: * Manometer (pressure gauge) for load weight determination (axles separated into 2 air suspension circuits) * Side underrun protection * Swing-down supports at the rear of the chassis frame * Mechanically adjustable warning boards, front and rear Hnodpfel Tnu Aex Apnep * Front axle plastic mudguards with spray protection * Rear axle straight galvanized steel side skirts with spray protection * Reflective contour tape on the sides and rear * Tool box, black powder-coated galvanized steel, approx. 1,000 mm wide, 600 mm deep, 300 mm high ----Low Loader Platform: * Front extension in front of the turntable platform, approx. 490 mm long with 45° corners * ROBOT-WELDED anti-slip coating on the steel plate of the turntable platform * Hardwood flooring on the running areas of the low-bed platform ----Load Securing (La-Si package consists of): * 1 x 13.4 t UVV lashing ring left & right in front of the headboard carrier * 4 fixing holes each side in the turntable platform, each with 2 t lashing capacity * 1 pair of lashing rings (13.4 t), suspended at the rear left & right in front of the rear carrier * 4 pairs of UVV lashing rings (10 t) per side, pivotable and lowerable, loadable in all directions and recessed into the external frame * 3 stake pockets per side, each offering 2 t lashing capability simultaneously ----Widening Package: * Hot-dip galvanized mechanical folding outriggers for 3 m overall width (not in the rear slope) * Beam bracket for widenings under the chassis on the left, longitudinally mounted ----Excavator Arm Rest: * Excavator arm rest above the rear axle up to the end cross member, approx. 2,100 mm long and approx. 190 mm deep * 2 pairs of 6.4 t lashing rings per side in the excavator arm rest ----Ramps: * Hydraulically operated one-piece drive-on ramps (approx. 3,000 x 720 mm), mechanically adjustable sideways * Outer planks of the ramps made from hardwood * Steel construction prepared for 6-way control valve ----Loading Height: * Loading edge unladen approx. 950 mm +/- 20 mm ----Tyres: * Tyres 235/75 R 17.5 ----Coating/Paintwork: * Chassis, turntable, folding outriggers, mechanical supports, and drive-on ramps hot-dip galvanized * --Axles, air tanks, drawbar painted black-- ----Infos: * Vehicle has a daily registration as of 07/2024, due to the missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery Time: * Available immediately from Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.900 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, ETÜ-TA-R 14.4 Hedpfxspk Dv Ro Apnonp ----Braking System: * EBS Electronic Braking System * Emergency release mechanism for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Air suspension ----Tow Bar / Flange Towing Eye: * Height-adjustable tow bar, adjustable by 300 mm * Tow bar extension by 250 mm to a total of 2,250 mm * 40 mm flange towing eye ----Lighting / Electrics: * Tire pressure monitoring system (TPMS) * LED rear lights 12 / 24 V * 15-pin power connector ----General Attachments: * Jost landing gear at the front * Externally mounted hot-dip galvanized folding supports at the rear * Plastic toolbox on the front right side of the headboard * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood floor * Preparation in front of the headboard for retrofitting container locks * Bolted headboard made of smooth sheet metal * Trapezoidal profiled drop-side walls made of steel, foldable with drop-side spring assist * Steel rear wall insertable between ramp mounts; when not in use, stowed inside in front of the headboard * Bolt-on rear posts * Rear approach angle approx. 860 mm ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Possible installation of 3 t drop lashing rings every 600 mm * One 6.3 t lashing point in each front and rear corner * Various holes in the front and rear cross member for 1.2 t lashing options ----Ramps: * One-piece mechanical grid ramps with spring assistance for single-person operation, approx. 2,750 x 600 mm (can be telescoped down to 20 mm) ----Painting: * Hot-dip galvanized chassis as well as tow bar, headboard, rear wall, tailgate, and ramps * Side wall color RAL 9010 pure white * Painting of side walls in a RAL color of choice available at extra cost ----Information: * --Reinforced and certified body according to EN 12642 XL incl. load securing certificate-- * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Available immediately ex works Egestorf

Stanje: novo, največja dovoljena obremenitev: 8.780 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2024, * KA-TA-R 11.9 Masterline: ----Brakes: * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem equalization unit ----Drawbar / Flange Eye: * Height-adjustable hot-dip galvanized drawbar, adjustable by 300 mm, with 40 mm flange eye ----General Attachments: * Jost mechanical landing gear (front) * Two rear mechanical hot-dip galvanized fold-down supports * Tool box made of galvanized steel sheet, mounted right side * Plastic quarter mudguards ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin electrical connector * Bolted underride guard with LED tail lights ----Tipping Platform: * Net hooks on the sides and rear in the central locking mounts as well as 3 external on the front wall Hnodpfjpk D Dmsx Apnop * Hot-dip galvanized chassis * Steel pallet 3-way tipper body, fully galvanized * Continuous, drop-side walls with spring-assisted board wall lifters, can be folded down—no center stanchions * Tailgate foldable and pendulum-mounted via manual central locking * Hot-dip galvanized bolted rear stanchion ----Load Securing: * 1 recessed and foldable 5 t lashing ring in each corner, as well as 4 recessed and foldable 3 t lashing rings on each side in the outer frame * 4 mm steel sheet floor, rear mount rail for ramps ----Ramps: * 1 pair aluminum loading ramps approx. 3,570 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment under the loading area at the rear, integrated into the chassis ----Tires: * 235/75 R 17.5 tires ----Paint Finish: * Axles, springs, air tanks, drawbar and landing gear painted in black * Vehicle is hot-dip galvanized ----Notes: * Reinforced body with load securing certificate according to EN 12642 XL * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery Time: * Available immediately from Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 8.870 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-ER 11.9: ----Braking System: * Electronic braking system (EBS) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 5.5 t Gigant axle units ----Suspension: * Parabolic springs with balancing unit ----Drawbar / Flange Eye: * Drawbar height adjustable by approx. 300 mm * 40 mm flange towing eye ----General Attachments: * Jost mechanical landing gear at front * Bolt-on, hot-dip galvanized folding supports at rear (external) * Side underrun protection * Plastic quarter mudguards * Plastic toolbox on front right, externally mounted on front wall ----Electrics / Lighting: * Tyre pressure monitoring system (TPMS) * 15-pin power connector * LED tail lights ----Load Area: * 50 mm softwood floor * 20" container locks mounted at front and rear * Bolted bulkhead made of smooth steel sheet * Drop sides made of trapezoidal-profile steel sheet, foldable with sideboard spring lifter * Hot-dip galvanized bolted rear stanchions ----Load Securing: * Perforated outer rail, edged at approx. 45°, with lashing capacity of 2 t every 480 mm * Optional 3 t folding lashing brackets every 600 mm (five lashing rings mounted per side) * One 6.3 t lashing ring in each corner, front and rear * Various bores in front and rear crossmembers for 1.2 t lashing points ----Ramps: * 1 pair of aluminium loading ramps, approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles Hnjdjl Tilxopfx Apnsp * Rear storage compartment recessed into the chassis frame under the loading area ----Paintwork: * Hot-dip galvanized chassis, drawbar, bulkhead, and rear wall * Sideboard colour in RAL 9010 pure white * Painting of side walls in a RAL colour of choice available at extra charge ----Information: * New vehicle, not registered * Subject to errors and prior sale ----Delivery Time: * Available immediately from Egestorf

Stanje: novo, največja dovoljena obremenitev: 6.870 kg, skupna masa: 9.900 kg, konfiguracija osi: 1 os, Leto izdelave: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brakes * Emergency release device for spring-loaded cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Coupling Eye: * Drawbar with 40 mm bolted towing eye (height-adjustable) ----Electrics / Lighting: * 15-pin power connector * LED lighting * Flashing LED side marker lights * RDÜ tire pressure monitoring system ----General Attachments: * Support winch at the front * Spring-assisted square tube supports at the rear with base plate, safety lock pin for various support heights * Enclosed steel mudguards with spray protection * Enclosed side underrun protection usable as advertising panel * Plastic toolbox with floor insert (installed horizontally), approx. 500 x 350 x 400 mm ----Body: * Swiveling cable drum body, clear width between drum arms 1,700 mm, with tension lock for securing drums at the support arm ends, as well as a central claw lock to secure the cable drum body to the chassis * Motor-hydraulic drum drive with hydraulic motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft with 76 mm diameter including centering and rotating ends * 1 pair of polyamide centering cones, stepwise offset ----Chassis: * Chassis made of torsion-resistant square tubes and cross beams ----Pump Unit: * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen Weight: * 2,690 kg unladen weight ----Paintwork: * Vehicle hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale reserved ----Delivery Time: Hnjdpfxsu I Iqxj Apnop * Immediately available ex Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 12.080 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, prva registracija: 06/2024, dolžina tovornega prostora: 3.900 mm, širina tovornega prostora: 1.920 mm, višina nakladalnega prostora: 415 mm, Leto izdelave: 2022, Oprema: ABS, * ETM-TA 14.4: ----Brakes: * Wabco ABS braking system * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer unit ----Drawbar / Flange Drawbar Eye: * Height-adjustable drawbar (+/- 150 mm) * 40 mm bolt-on drawbar eye ----General Attachments: * Jost landing gear at the front * Lateral underrun protection * Foldable A-frame shield at the rear ----Electrics / Lighting: * 15-pin power socket * Multi-chamber taillights ----Body: * Fixed steel front and side walls * Removable steel rear wall * Floor made of 50 mm softwood * 1 sliding steel plate support 750 x 1,000 mm at the front, incl. 2 interchangeable skip stops at the front, plug-in at 2 positions each * Rear crossmember designed for aluminum loading ramps, incl. 2 additional drop-down supports at the rear ----Loading Edge: * Unloaded loading height approx. 710 mm ----Load Securing: * 4 repositionable skip stops, can be placed in 2 positions for lateral centering of skips * Each side with 1 x (13.5 t) UVV tie-down point for securing lashings * 2 ratchet tensioners (spindle adjustment) with balancing chain and quick shortener (tension force 6,300 kg) ----Tyres: * Tyres: 285/70R19.5 ----Wheelbase: * Wheelbase: 1,140 mm Hnjdpfxsl Th Dms Apnjp ----Paint / Finish: * Chassis, front wall, side walls, mudguards, drawbar, rear drop supports hot-dip galvanized * Axles, springs, landing gear, and air tanks painted in black ----General Information: * Vehicle has a day registration from 06/2024 due to missing tire pressure monitoring system and has not been loaded/used * Errors and prior sale excepted ----Delivery Time: * Available immediately from Egestorf on the A7

Stanje: rabljeno, največja dovoljena obremenitev: 14.300 kg, skupna masa: 20.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2023, naslednji pregled (TÜV): 11/2026, Leto izdelave: 2023, * HL - TA 20.0 ----Brakes: * Wabco EBS-E braking system * Emergency release system for spring-loaded cylinders * Drum brakes * Duomatic brake connection ----Axles: * 2 x ton SAF axles * 1st axle as lift axle (fully automatic) * Lift axle with ride height +30 mm via positioning cylinder * Starting aid for shunting and mandatory lowering on the first axle – controlled via speed-dependent EBS electronics (no installation required on the truck; also with cable for operation from the tractor) ----Air Suspension: * Air suspension with lowering function via radio remote control ----Drawbar / Flange Drawbar Eye: * 50 mm flange-mounted drawbar eye, height-adjustable by +77 mm and -33 mm, for 2 t support load ----Electrics / Lighting: * 15-pin power connector * 3-pin 12V auxiliary connector * LED lighting system 12 / 24V * 2 LED reversing lights, switched via reverse gear * EBS multi-voltage system for towing vehicles with 12 & 24V electrics * Extended connecting cables for agricultural and forestry vehicles * Power supply for radio remote: 12+24 V via taillight ----General Attachments: * BPW landing leg at the front * Mechanically extendable underrun protection for container lengths over 6,000 mm * Speedline diamond-finish aluminium wheels * Split-pin towing coupling (use only with retracted underrun protection) * Enclosed plastic half-shell single mudguards * Two-step access before the front bulkhead on the left side * Shovel and broom holders in front of the front bulkhead * 2 matte stainless steel toolboxes, approx. 650 x 350 x 320 mm, mounted right side * Enclosed side protection usable as advertising space ----Hydraulics: * 2-circuit hydraulic connections (engine end from truck/tractor), rated for 180 bar (tractor operation) * Double-acting control circuit for hydraulic tailgate (mounted front right), operated via radio remote control ----Hooklift: * Palfinger PHT 20 SCASNSLD5 telescopic hook system (Serial no. 100746129, year 2023) * Base frame made of high-strength fine-grained steel * 20,000 kg pulling force * Hook height 1,570 mm Hnsdpfxjx Dp Ato Apnsp * Control of hooklift via radio remote control * Remote control with rapid function when lowering, not when raising * Emergency stop switches left and right sides * Container supports with 4 lateral supports per side and one roller at the rear * Hydraulic rear internal locking * 2 additional hydraulic cylinders to assist in lifting the main arm * 2 x mechanical fall supports at the rear * Approval for 20 t gross vehicle weight (2 x 9 t axles) and 2 t support load * Note: If the radio remote is outside the charging cradle, the service brake must be applied for radio release. Brake connections must remain connected at all times so the hydraulically/pneumatically operated valves can be opened. * Monitoring system for underrun protection to ensure it is retracted when tipping ----Loading Height: * Unladen approx. 1,300 mm with lowered lift axle ----Paintwork: * Chassis, drawbar, access steps, underrun protection, and fall supports hot-dip galvanized * Axles, air tanks, front landing gear painted black * Palfinger hooklift painted black/yellow ----Information: * Errors and prior sale reserved * Vehicle is in very good / as-new condition ----Delivery time: * Vehicle is immediately available

Stanje: novo, največja dovoljena obremenitev: 9.070 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.010 mm, višina nakladalnega prostora: 325 mm, Leto izdelave: 2026, * ETS-TA-B 11,9: * Wabco EBS (elektronski kočioni sistem) * RDÜ (nadzor pritiska u pneumaticima) * Bubanj kočnice, 2 x 5,5 t Gigant osovine * Parabolične opruge sa balans agregatom * Vučna ruda podesiva po visini oko 300 mm * BPW oslonac (nožna dizalica) * Mehaničke zadnje potpornice * Plastična kutija za alat napred desno uz čeonu stenu * Bočna zaštita od podlijetanja Hnedpfx Aowyhzvepnop * LED osvetljenje * Pod od mekog drveta (nordijska jela) debljine 50 mm * U uglovima ispred čeone stene i zadnjeg nosača po 1 x 6,3 t anker, kao i sa svake strane po 2 UVV ankerska prstena od 6,3 t ugrađena u spoljašnji ram * Jednodelne mehaničke rampe od rešetkastog metala sa oprugom za upravljanje jednom osobom, dimenzija cca 2.350 x 870 mm (unutrašnje rastojanje 20 mm, rampe nisu pomične) * Čeona stena, bočne stranice, blatobrani i vučna ruda toplo pocinkovani * Osovine, opruge, vazdušni rezervoar, prednji oslonac lakirani u crnoj boji * Novo vozilo sa punom fabričkom garancijom * Zadržavamo pravo na greške i međuprodaju * Dostupno od približno 35. nedelje 2026.

Stanje: novo, največja dovoljena obremenitev: 13.830 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 4.995 mm, širina tovornega prostora: 2.380 mm, višina nakladalnega prostora: 900 mm, Leto izdelave: 2026, * KA-TA-R 18 ----Brakes: * EBS-E (electronic braking system with RSS) * Emergency release for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 9 t Gigant axles ----Suspension: * Air suspension with level control during tipping ----Electrics / Lighting: * Tire pressure monitoring system with display possibility in the truck dashboard via EBS signal – no installation required on the truck side * 15-pin power connector * LED lighting with galvanized protective cover * 2 LED reversing lights ----Drawbar eye / Drawbar: * Drawbar with 50 mm flange towing eye (adjustable by +77 mm and -33 mm using offset plate) ----General attachments: * Landing leg at the front * Foldable galvanized steel underrun guard for paver feeding * Enclosed single plastic mudguards * Front wall platform made of grating with step on drawbar and handholds on the front wall ----Chassis: * Chassis made of fine-grain steel ----Tipper body: Hnjdjx Ipbyepfx Apnop * Steel 3-way tipper body with continuous asymmetrical aluminum side walls – without center stanchion – pendulum-mounted with manual central locking, left side foldable with side board spring lifter * Tailgate – made from HBW 400 steel – pendulum-mounted with automatic 2-claw lock * 5 mm steel floor made from HBW 450 steel ----Load securing: * 4 x 3 t lashing rings per side – recessed and foldable – integrated into the steel floor ----Roll tarp: * Roll tarp – agate grey, similar to RAL 7038 * Tarpaulin tensioning using ratchet tensioners on the sides and tensioning rubber at the front and rear ----Painting: * Chassis, underrun guard, and drawbar hot-dip galvanized * Axles, air tanks, landing leg, and flange towing eye painted in a shade of black * Side wall painting according to RAL color of choice (excluding special or metallic paints); color can be changed up to approx. 6 weeks before completion ----Info: * Reinforced and certified body according to EN 12642 XL, including load securing certificate up to 19 t * New vehicle without first registration, with manufacturer’s warranty * Subject to errors and prior sale * Sample images (vehicle images may vary due to special equipment) ----Delivery time: * Vehicle available from week 42/2026

Stanje: novo, največja dovoljena obremenitev: 18.900 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA-Kombi 24.0: ----Braking System: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Suspension: Hnjdpfx Ajtplv Tjpnjp * Air suspension with manual lowering at the rear ----Axle: * 3 x 11 t Gigant axles * Lifting middle axle ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm towing eye and height adjustment device ----Electrics / Lighting: * LED tail lights * 15-pin power connector * TPMS (Tire Pressure Monitoring System) ----General Attachments: * Toolbox made of powder-coated steel sheet (W: 1,000 mm x H: 300 mm x D: 450 mm) * Storage box for container nets made of galvanized steel sheet (W: 960 mm x H: 300 mm x D: 450 mm) * Side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear bumpers * Mechanical rear drop-down supports ----Container / Low-bed Platform: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm raised) for guiding roll-off containers * Steel floor with roller recesses in the bogie area * For roll-off container transport, container length of 5,500 - 7,000 mm possible * Pneumatic 4-point container clamp locking as well as mechanically plug-in front stop angles in the guide tracks * Load certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. 10 m³ capacity possible * Includes 8 repositionable skip stops for lateral centering of the skips, front 4 skip stops plug-in with pendulum stoppers ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning devices for positive and non-positive load securing of skips * 4 lashing rails in cloverleaf design (side) and 1 pair of 13.4 t UVV lashing rings at the front * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 ----Ramps: * Weld bead as anti-slip coating in the ramp incline running area * 1 pair of aluminum approach ramps (16 t/pair) 2,800 x 400 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Tyres: * Tyres: 235/75 R17.5 ----Ride Height: * Loaded ride height approx. 1003 mm ----Payload: * Payload 18,900 kg ----Paintwork: * Reflective contour tape on sides and rear * Axles, turntable, drawbar and air tanks painted in black * Hot-dip galvanized main frame ----Information: * Permissible gross weight of 27,000 kg technically possible * New vehicle without initial registration with manufacturer warranty * Subject to errors and prior sale ----Delivery Time: * Available from approx. week 47/2026

Stanje: novo, največja dovoljena obremenitev: 13.500 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA-Kombi 18.0: * 3-in-1 = for roll-off containers, skip containers, and as a low-loader ----Brakes: * TPMS (Tire Pressure Monitoring System) * EBS-E (Electronic Braking System) * Emergency release device for spring brake cylinders ----Axles: * 2 x 12 t Gigant axles ----Suspension: * Parabolic springs ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long * 40 mm drawbar eye with height adjustment device ----Electrics / Lighting: * LED tail lights * 15-pin power connector * TPMS, display option in the truck via EBS signal (no installation required on the truck side) ----General Attachments: * Toolbox made of powder-coated steel sheet, right side * Side underrun protection * Plastic quarter mudguards with spray protection * Storage box made of galvanized sheet metal for container nets, approx. 960 x 300 x 400/450 mm, right side * Plastic bumper buffer at rear Hjdpfxol Thv Rj Apnjnp * Mechanical drop-down supports at rear ----Load Area: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm raised) to guide roll containers * Steel floor with roller recesses in the bogie area * Possible to transport roll-off containers with a length of 5,500–7,000 mm * Pneumatic four-point clamp locking as well as mechanical locking angles at the front in the track, securing certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. volume of 10 m³ possible * Includes 8 removable tub stops for lateral centering of the tubs; front 4 stops plugged in with pivotable stop * Weld bead as anti-slip coating in the ramp area of the run-up incline ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning elements to securely fix the tubs * 4 lashing bars per side, cloverleaf design * 1 pair of 13.4 t UVV lashing rings at the front ----Ramps: * 1 pair of aluminium drive-on ramps (10.6 t / pair), 2,800 x 470 mm, suitable for rubber-wheeled and tracked vehicles (lockable storage compartment accessible from the rear) ----Information: * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 * Permissible gross weight up to 20,000 kg technically possible * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Available from approx. calendar week 44 / 2026

Stanje: novo, največja dovoljena obremenitev: 13.500 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA-Kombi 18.0: * 3 in 1 = for roll-off containers, skip containers, and as a low-loader ----Brakes: * TPMS (Tire Pressure Monitoring System) * EBS-E (Electronic Braking System) * Emergency release device for spring brake cylinders ----Axles: * 2 x 12 t Gigant axles ----Suspension: * Parabolic springs ----Drawbar: Hsdpfx Apol Thwconenp * Pneumatically lowerable drawbar, 2,100 mm long * 40 mm towing eye and height adjustment device ----Electrical / Lighting: * LED tail lights * 15-pin power connector * TPMS, display option in the truck via EBS signal (no truck-side installation required) ----General Attachments: * Tool box made of powder-coated sheet steel, right side * Side underrun protection * Plastic quarter mudguards with spray protection * Storage box for container nets, made of galvanized sheet, approx. 960 x 300 x 400 / 450 mm, right side * Plastic rear collision protection buffers * Mechanical drop-down supports at the rear ----Loading Area: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) to guide roll containers * Steel floor with roller recesses in the bogie area * For roll-off container transport, possible container length from 5,500 to 7,000 mm * Pneumatic 4-point clamp locking as well as mechanically insertable stop angles at the front in the track, load securing certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. 10 m³ volume possible * Includes 8 removable skip stops for lateral centering of the skips, front 4 skip stops inserted with pendulum mount * Weld bead as anti-slip coating in the ramp area ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the side for attaching tension elements for positive and non-positive securing of the skips * 4 lashing bars each, cloverleaf design (side) * 1 pair of 13.4 t UVV lashing rings to the front ----Ramps: * 1 pair of aluminum access ramps (10.6 t/pair), 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Information: * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 * Permissible gross weight of 20,000 kg technically possible * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available from approx. CW 44 / 2026

Stanje: novo, največja dovoljena obremenitev: 8.850 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2024, * KA-TA-R 11.9 "Masterline" ----Brakes: * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem compensating unit ----Drawbar / Flange Eye: * Approx. 300 mm height-adjustable drawbar with 40 mm flange eye ----General Fittings: Hnedel Thyxopfx Apnep * Jost mechanical landing gear at front * Rear: 2 mechanical, hot-dip galvanized drop-down support legs * Plastic toolbox approx. 750 x 350 x 300 mm, fitted on right side * Bolted underrun protection * Plastic quarter mudguards ----Electrics / Lighting: * 15-pin power connector * LED lighting * TPMS tire pressure monitoring system ----Tipping Platform: * Mesh hooks on the sides and rear in the central locking fixtures, plus 2 at the front wall * Steel pallet, 3-way tipping body (continuous sidewalls – without center stanchions – foldable with drop side spring assistance) * Rear stanchions bolted * Combination steel double rear doors, asymmetrically split, can be swung open and locked at 270°, not foldable – with additional pendulum frame for automatic tailgate opening during tipping operation; locking via galvanized swing bolt locking and central locking system * Deactivation function for automatic rear wall opening when tipping backwards with open door * 4 mm steel floor plate * Rear ramp carrier rail for drive-on ramps ----Load Securing: * 1 x 5 t lashing point in each corner * 4 x 3 t recessed lashing rings per side, fitted in the outer frame ----Ramps: * 1 pair of aluminum drive-on ramps approx. 3,310 x 400 mm (load capacity 8 t / pair), suitable for vehicles on rubber tires & tracks * Lockable storage compartment for ramps under the loading platform, integrated into the chassis ----Paint Finish: * Drawbar, front wall, tipping platform, rear stanchions, underrun protection, and mechanical support legs hot-dip galvanized * Sidewalls and tailgate painted RAL 9010 pure white * Sidewall painting in any RAL color available at extra charge * Axles, springs, flange eye, air tank, and landing gear painted in a black tone ----Information: * Body reinforced with load securing certificate according to EN 12642 XL * New vehicle without initial registration, with manufacturer’s warranty * Errors and prior sale excepted ----Delivery Time: * Immediately available ex-works Egestorf on A7

Stanje: rabljeno, največja dovoljena obremenitev: 12.080 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, prva registracija: 06/2024, dolžina tovornega prostora: 3.900 mm, širina tovornega prostora: 1.920 mm, višina nakladalnega prostora: 415 mm, Leto izdelave: 2022, Oprema: ABS, * ETM-TA 14.4: ----Brakes: * Wabco ABS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer unit ----Drawbar / Flange towing eye: * Height-adjustable drawbar (+/- 150 mm) * 40 mm bolt-on towing eye ----General attachments: * Jost landing gear at the front * Side underrun protection * Foldable A-panel at the rear ----Electrics / Lighting: * 15-pin power connector * Multi-chamber tail lights ----Superstructure: * Fixed steel front and side walls * Removable steel rear wall * Floor made of 50 mm softwood * 1 sliding plate cover 750 x 1,000 mm at the front incl. 2 removable skip stops, front in 2 positions * Rear cross member for attaching aluminium ramps, incl. 2 additional drop-down supports at the rear Hnjdpjl Th Eyofx Apnjp ----Loading edge: * Unloaded loading edge approx. 710 mm ----Load securing: * 4 removable skip stops, can be inserted into 2 positions for lateral centring of the skips * On each side: 1 x (13.5 t) UVV lashing point for attaching tensioning devices * 2 ratchet tensioners (spindle adjustment) with compensating chain and quick-shortener (tensioning force 6,300 kg) ----Tyres: * Tyres: 285/70R19.5 ----Wheelbase: * Wheelbase: 1,140 mm ----Paintwork: * Chassis, front wall, side walls, mudguards, drawbar, rear drop supports hot-dip galvanized * The axles, springs, landing gear, and air tank painted in a black tone ----General information: * Vehicle has a one-day registration in 06/2024, due to missing tyre pressure monitoring system it has not been loaded/used * Subject to errors and prior sale ----Delivery time: * Immediately available ex Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lift/lowering system and RtR valve * Smard board for load weight determination * Warning sign packages front & rear Hnsdpfxjl Tphrs Apnop * Reflective contour marking tapes on sides and rear * Rotating beacon (removable) at rear * LED lights * Straight drawbar with 50 mm towing eye and continuously adjustable height * Tool box made of powder-coated sheet steel and spare wheel holder in basket design, right-hand side * Closed single plastic mudguards at front * Straight rear steel splash guards, each with spray suppression * Side underrun protection * Turntable platform front extension by 520 mm with 45° corners and 3 flush storage compartments with lids, lockable * Chassis made of high-strength fine-grained steel * Decking above turntable platform: 50 mm softwood, in low-bed platform: 60 mm softwood * Outer planks of access ramps: hardwood * Each side features 4 stake pockets (stakes not included), with simultaneous 2 t lashing points * Lashing package includes: 2 lashing rings 6.4 t, front left and right on main frame of turntable platform * On sides, front & rear, 2 pairs of 13.4 t lashing rings on outer frame; sides each with 4 pairs of 10 t lashing rings, pivoting & lowerable * Loadable in all directions, recessed in the outer frame * 2 pairs of 6.4 t lashing rings on the excavator stick rest area * 8 pairs of galvanized folding outriggers for 3 m overall width (not in the rear slope) * Extension planks stored left side in a stowage compartment * Excavator stick rest above rear axle to rear slope approx. 2,100 x 740 x 190 mm * Mechanical drop supports, rear * Hydraulic folding ramps with hydraulic tip section approx. 4,650 x 720 mm including lateral hydraulic ramp shift & load holding valve * Load area over turntable: approx. 2,990 x 2,520 mm * Rear load area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm drive-on slope) * Flow divider installed * Chassis, turntable, ramps, outrigger arms, and mechanical rear supports hot-dip galvanized * Axles, drawbar, air reservoir, and turntable painted in a black tone * Tires: 235/75 R 17.5 * New vehicle, not previously registered, with manufacturer warranty * Subject to errors and prior sale * Immediately available ex Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 13.700 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA 18.0: * 2-in-1: Suitable for swap containers (Abrollbehälter) and as low-loader trailer ----Braking System: * EBS electronic braking system * Emergency release facility for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 10-ton axles ----Suspension: * Air suspension with lift and lower system and RTR valve ----Drawbar: * Drawbar 2,000 mm long with 40 mm towing eye and height adjustment device ----Electrics / Lighting: * Tire pressure monitoring system, display option in truck via EBS signal (no truck-side installation required) * LED rear lights 12 / 24 V * 15-pin power connector ----General Attachments: * Tool box, powder-coated steel, approx. 1,000 x 300 x 600 mm * Storage box for container net, galvanized sheet metal, 960 x 300 x 450/400 mm * Reflective contour tape on sides and rear * Side underrun protection * Plastic quarter mudguards with splash guards * Rear plastic buffer bumper * Foldable 'A' sign at the rear ----Loading Platform: * Main frame with raised outer frame to guide swap containers * Steel sheet floor with recesses for rollers in the bogie area * Container length possible from 5,500 to 7,000 mm * Pneumatic 4-point clamping lock and mechanical plug-in stops in the running channel at the front, securing certificate according to DIN 30722-1 * Weld bead as anti-slip covering in the inclined running area * Mechanical drop-down supports at the rear ----Load Securing: * 1 pair 10 t UVV lashing rings at the front wall carrier * 3 pairs 10 t UVV lashing rings on each side of the outer frame * Each side with 4 x 2 t cloverleaf lashing eyes * 4 x 8 t recessed lashing brackets in the outer frame Hjdol Tq Nmjpfx Apnenp ----Ramps: * 1 pair aluminum loading ramps (10.6 t/pair) 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from rear) ----Paintwork: * Chassis, bogie, locking elements, rear drop-supports hot-dip galvanized * Drawbar, axles, and air tanks painted in a black shade ----Additional Info: * New vehicle, no initial registration, full manufacturer warranty * Subject to errors and prior sale * Sample images ----Delivery Time: * Available approx. from KW 43 / 2026

Stanje: novo, največja dovoljena obremenitev: 6.870 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2026, * KWH 9.9 ML: ----Brakes: * EBS brake system * Drum brakes * Emergency release device for spring-loaded cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange eye: * Drawbar with 40 mm screwed towing eye (height adjustable mm) ----Electrics / Lighting: * 15-pin power connector * LED lighting * Flashing LED side marker lights * RDÜ tire pressure monitoring ----General attachments: * Support winch at the front * Spring-assisted square tube supports at the rear with base plate; safety locking pins for various support heights * Closed steel sheet mudguards with splash protection * Closed side underrun protection, can be used as advertising space * Plastic toolbox with floor insert (installed horizontally), approx. 500 x 350 x 400 mm ----Superstructure: * Pivoting cable drum superstructure, clear width between drum arms 1,700 mm, with tension locks for securing the drum at the ends of the support arms, and central claw locking device securing the drum superstructure to the chassis * Motor-hydraulic drum drive with oil motor * Valves and movable, rubber-covered drive rollers * Hydraulic speed controller and brake for drum drive * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 1 pair of stepwise offset centering cones made of polyamide ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Pump unit: * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen weight: * 2,690 kg unladen weight ----Paintwork: * Vehicle is hot-dip galvanized Hnsdpou I Iqlefx Apnsp ----Information: * New vehicle with full manufacturer warranty * Subject to errors and prior sale ----Delivery time: * Immediately available ex Egestorf