Priklopnik sedeža z delovno ploščadjo

MÜLLER-MITTELTAL 3-achs mit Radmulden, 2 Ladehöhen, Klapprampen

Stanje: novo, največja dovoljena obremenitev: 37.390 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Start-up aid for maneuvering purposes switched to the first axle via EBS (no installation required on the truck side) * Rear axle as self-steering axle with electro-pneumatic steering lock * Locking of the self-steering axle from the driver's cab for maneuvering purposes, controlled via EBS (no installation required on the truck side) ----Suspension: * Air suspension with lifting/lowering device and Ride-to-Return valve Isdeq Euakopfx Adxjhu ----Electrics / Lighting: * Smart Board mounted on the trailer as an information tool with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12/24 V * LED rotating beacon (removable) at the rear * 2 additional LED reversing lights * 7-pin socket at rear for extended length lighting * Side marker lights with indicator signal control * Tyre pressure monitoring system with display option in the truck via EBS signal (no installation required on the truck side) ----General equipment: * Side underrun protection * Landing gears at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the front wall crossmember (without spare wheel) * Mechanically adjustable warning sign packages at front and rear * Swing arm as carrier for connecting cables from truck to semi-trailer ----Low loader deck: * 2nd king pin position * Fifth wheel platform with 45° chamfered front corners and front tool box made of galvanized powder-coated sheet steel B = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm high aluminium side boards (in RAL colour of choice) on the sides of the fifth wheel platform, foldable and removable * Rear wall -150 mm- high plug-in * Rear slope on fifth wheel platform to low bed approx. 700 mm long with tread plate covering and at the end a perforated strip for attaching aluminium loading ramps * Fifth wheel platform with 50 mm clamped wooden planks and low bed platform with 60 mm clamped wooden planks * Tear plate above the axles * 9 x mechanical folding extensions to 3 m overall width, but not in the rear slope (extension planks available with closed storage compartment across the direction of travel under the loading floor) * 3 mounting shafts under the fifth wheel platform for storage of optional aluminium loading ramps or wooden planks for wheel well coverings ----Load securing (LaSi package): Fifth wheel platform: * Perforated outer frame angled at 45° with hole pattern for lashing points (2 t lashing capacity per point at a minimum spacing of 480 mm) * 3 x 13.4 t lashing rings each side recessed in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal beams after the drop, 1 x above the centre axle next to the longitudinal beam) Low loader platform: * 3 x 13.4 t lashing rings each side on the outer frame (1 x beginning of the drop on the fifth wheel platform, 1 x beginning of the ramp slope, 1 x end of the ramp slope) * 2 x 10 t lashing rings each side (1 x between front wheel well and 1st axle, 1 x between 2nd and 3rd axle) * 3 x 5 t lashing rings each side bolted to the outer frame of the wheel wells (2 on the front wheel well, 1 on the rear wheel well) ----Excavator arm recess: * Extended excavator arm recess from end of last fixed axle through to steering axle up to rear crossmember, continuous with

Stanje: novo, največja dovoljena obremenitev: 37.390 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Traction aid for shunting purposes engaged on the first axle via EBS (without truck-side installation) * Last axle as trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle from the driver's cab for shunting via EBS (without truck-side installation) ----Suspension: * Air suspension with lifting and lowering function as well as RtR valve ----Electrics / Lighting: * Smart Board mounted on trailer as info tool with pressure sensors for total axle load display * 15-pin electrical connector * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * 2 extra LED reversing lights * 7-pin socket at the rear for additional length lighting * Side marker lights with indicator activation * Tire pressure monitoring system with display option in the truck via EBS signal (without truck-side installation) ----General attachments: * Side underrun protection * Landing gears at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the headboard crossmember (without spare wheel) * Mechanically adjustable warning sign packages at the front and rear * Swivel arm as carrier for connection cables from truck to semi-trailer ----Lowbed platform: * Second kingpin position * Fifth wheel platform with 45° bevelled front corners and front toolbox made of galvanised, powder-coated steel sheet, W = 2,480 mm x H = 500 mm x L = 665 mm with folding lid * Side aluminium drop sides, 400 mm high (in RAL custom colour), foldable and removable * Rear wall -150 mm- high plug-in * Rear slope on the saddle platform to the lowbed approx. 700 mm long with chequer plate covering and a perforated strip at the end for attaching aluminium loading ramps * Fifth wheel platform with 50 mm clamped wooden planks and lowbed platform with 60 mm clamped wooden planks * Tread plate over the axles * 9 x mechanical folding wideners to 3 m overall width, not in rear slope (widening planks available with sealed crosswise storage compartment under the loading area) * 3 mounting shafts under the saddle platform for the storage of either aluminium loading ramps or wooden planks for wheel well covering Ihsdjtpta Dopfx Adxsu ----Load securing (LaSi-package): Fifth wheel platform: * Perforated outer frame, 45° angled, with hole pattern for lashings (2 t lashing capacity per tie-down point at a minimum spacing of 480 mm) * 3 x 13.4 t recessed lashing rings per side in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal members after the cranking, 1 x above the central axle next to the longitudinal member) Lowbed platform: * 3 x 13.4 t lashing rings per side on the outer frame (1 x at the start of the cranked platform, 1 x at the start of the access slope, 1 x at the end of the access slope) * 2 x 10 t lashing rings per side (1 x between the front wheel well and 1st axle, 1 x between the 2nd and 3rd axle) * 3 x 5 t lashing rings per side bolted to the outer frames of the wheel wells (2 at the front wheel well, 1 at the rear wheel well) ----Excavator arm rest: * Extended excavator arm rest from end of last rigid axle over steering axle to end crossmember, continuous with internal reinforcing profile approx. W = 770 mm x D rear = 270 mm / D front = 170 mm * 2 x 6.4 t lashing rings per side in the exca

Stanje: novo, največja dovoljena obremenitev: 36.900 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Moving-off aid for shunting, connected to the first axle via EBS (no installation required on the truck side) * Last axle as self-steering trailing axle with electro-pneumatic lock * Trailing axle lock for shunting purposes, activated from the cab via EBS (no installation required on the truck side) ----Suspension: * Air suspension with lifting and lowering system, including RtR valve ----Electrics / Lighting: * Smart-Board infotool mounted on trailer with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear * 2 additional LED reversing lights * 7-pin socket at rear for overlength lighting * Side marker lights with indicator circuit * Tire pressure monitoring with display in the truck via EBS signal (no installation required on the truck side) ----General Attachments: * Side underrun protection * Landing gear at front, swing supports at rear of the chassis * Straight steel fenders * Spare wheel carrier in front of front wall crossmember (spare wheel not included) * Mechanically adjustable warning sign packages at front and rear * Swing arm as carrier for connection lines from truck to trailer ----Low Loader Deck: * 2nd kingpin position * Saddled platform with 45° chamfered front corners and front toolbox made from galvanized, powder-coated steel sheet (W = 2,480 x H = 500 x L = 665 mm) with folding lid * 400 mm high drop-down/removable aluminium sideboards (custom RAL color) on saddle platform * Removable 150 mm high rear wall * Rear inclined ramp of approx. 700 mm at the end of saddle platform to low-bed deck, fitted with checker plate and lashing bar for attaching aluminium approach ramps * Saddle platform with 50 mm tongued-and-grooved timber floor, low-bed platform with 60 mm tongued-and-grooved timber planks * Tread plate above axles * 9 x mechanical folding extensions to 3 m overall width, but not on rear ramp (extension planks included with lockable transverse storage compartment under load area) * Preparation for 3 ramp storage compartments under saddle platform for either aluminium ramps or timber planks for wheel trough covers * Preparation for container locks on the gooseneck ----Load Securing (LaSi Package): Saddle Platform: Ijdpfx Adoykx Nqsxjhu * Perforated external frame, angled at 45°, with hole pattern for lashing equipment (2 t lashing capacity per point, minimum spacing 480 mm) * 3 x 13.4 t recessed tie-down rings per side (1 on saddle platform, 1 on main longitudinal beams after the step, 1 above the center axle beside the beam) Low-bed Deck: * 3 x 13.4 t tie-down rings per side on outer frame (1 at the start of the gooseneck, 1 at the start of the rear ramp, 1 at the end of the ramp) * 2 x 10 t tie-down rings per side (1 between front wheel-well and 1st axle, 1 between 2nd and 3rd axle) * 3 x 5 t tie-down rings per side, bolted to the outer frame of wheel wells (2 at front, 1 at rear wheel well) ----Digger Arm Rest: * Extended digger arm rest from end of last fixed axle over steering axle to end crossmember, continuous with internal reinforcement profile, approx. W = 770 mm x D at rear