Polpriklopnik z nizko nakladalno ploščadjo

FAYMONVILLE Gigamax Tiefbett 1+3

Our complete vehicle inventory, including vehicles available immediately and at short notice, can be found on our website.

Below is an excerpt from the equipment list. Full specification available upon request.

GOOSENECK:
* Gooseneck with integrated single-axle running gear (pendulum axle) in a detachable version
* Gooseneck hydraulically liftable and lowerable, including hydraulic connection linked to the hydraulic axle compensation of the first axles
* Length: approx. 5,200 mm, with front tapering approx. 60°
* Fifth wheel load according to data sheet: W25-DSR2700-12/22.7
* For tractor units: 6 x 4 or 8 x 4
* Steel front wall, plug-in type, approx. 400 mm high, with beveled design
* 1 pair of mechanical supports at the front of the gooseneck
* ASPÖCK-UNIBOX on the front connector panel with 24N, 24S & 15-pin sockets
* 1 spare wheel holder inside the front wall of the gooseneck with jib
* 2 pairs of recessed lashing rings on the gooseneck (LC 2,500 daN)
* 2 pairs of recessed lashing rings on the outer frame of the running gear at the front, foldable outward (LC 10,000 daN)
* 1 pair of lashing rings at the transition from running gear to loading platform (LC 10,600 daN)
* On the gooseneck 1 pair of removable aluminum drop sides, approx. 400 mm high, anodized
* On the gooseneck 1 removable aluminum rear wall, approx. 400 mm high, anodized
* 3.5 inch kingpin
* TPMS tire pressure monitoring system according to ECE R 141
Ljdeyhkqnopfx Ab Hshd
* Round NATO socket on the front connector panel (Maeler & Kaege VG 96 917)
* 1 stainless steel toolbox with 1 lid, mounted on the gooseneck on the right in the direction of travel by the aluminum drop side, approx. 1,350 x 400 x 400 mm (L x W x H)

LOADING PLATFORM:
* Low-bed with external beams, designed as a telescopic loading platform in low-profile design with front extension including fixed approx. 50 mm thick hardwood floor
* Length x width approx. 8,000 mm x 2,740 mm
* Mechanical bolt-lug coupling from low-bed to running gear for swapping the loading platform or installing extension beams
* One locking position approx. every 500 mm on the extension
* 4 pairs of recessed lashing rings fitted flat in the loading platform along the outer frame/external beams (LC 10,000 daN)
* 1 lashing ring each on the left and right outer rear cross member (LC 10,000 daN)
* Foldable extensions, approx. 230 mm per side (WITHOUT wooden boards)
* Loose extension planks, steel-rimmed
* Preparation for installation of bolted container positions for 1x 20’ or 1x 40’ container on the outer beams. Without container locks
* 6 pairs of threaded blocks between the lashing rings under the top chord of the outer beam for mounting bolted M24 rings (LC 8,000 daN)
* 2 pairs M24 bolt rings (LC 8,000 daN) included

REAR RUNNING GEAR:
* Rear running gear with closed outer frame, checker plate decking and continuous prism-shaped excavator trough, approx. 1,450 x 900 x 505 mm, open at the rear
* PENDULUM AXLE, all axles hydro-mechanically forced-steered
* Hose rupture valve on axle compensation cylinder with automatic reset function
* Hydraulic cylinders with shut-off valves and foreplugs to secure in raised position
* Final paint of axles in 2 layers of 2-component paint, single color, DB 7350 Novagrau
* Technical axle load: 12,000 kg each
* Hydraulic axle compensation
* 245/70 R 17.5 3PMSF, brand at our choice
* Remote steering from front and rear via cable control, with axle alignment check, no installation in the tractor unit
* 4 pairs of hanging la

Oglas je bil avtomatsko preveden. Možne so napake pri prevodu.