Polpriklopnik z nizko nakladalno ploščadjo

MÜLLER-MITTELTAL 3-achs mit Radmulden, 2 Ladehöhen, Klapprampen

Stanje: novo, največja dovoljena obremenitev: 37.390 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Start-up aid for maneuvering purposes switched to the first axle via EBS (no installation required on the truck side) * Rear axle as self-steering axle with electro-pneumatic steering lock * Locking of the self-steering axle from the driver's cab for maneuvering purposes, controlled via EBS (no installation required on the truck side) ----Suspension: * Air suspension with lifting/lowering device and Ride-to-Return valve ----Electrics / Lighting: * Smart Board mounted on the trailer as an information tool with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12/24 V * LED rotating beacon (removable) at the rear * 2 additional LED reversing lights * 7-pin socket at rear for extended length lighting * Side marker lights with indicator signal control * Tyre pressure monitoring system with display option in the truck via EBS signal (no installation required on the truck side) Djdpfx Aeq Euakob Eecn ----General equipment: * Side underrun protection * Landing gears at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the front wall crossmember (without spare wheel) * Mechanically adjustable warning sign packages at front and rear * Swing arm as carrier for connecting cables from truck to semi-trailer ----Low loader deck: * 2nd king pin position * Fifth wheel platform with 45° chamfered front corners and front tool box made of galvanized powder-coated sheet steel B = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm high aluminium side boards (in RAL colour of choice) on the sides of the fifth wheel platform, foldable and removable * Rear wall -150 mm- high plug-in * Rear slope on fifth wheel platform to low bed approx. 700 mm long with tread plate covering and at the end a perforated strip for attaching aluminium loading ramps * Fifth wheel platform with 50 mm clamped wooden planks and low bed platform with 60 mm clamped wooden planks * Tear plate above the axles * 9 x mechanical folding extensions to 3 m overall width, but not in the rear slope (extension planks available with closed storage compartment across the direction of travel under the loading floor) * 3 mounting shafts under the fifth wheel platform for storage of optional aluminium loading ramps or wooden planks for wheel well coverings ----Load securing (LaSi package): Fifth wheel platform: * Perforated outer frame angled at 45° with hole pattern for lashing points (2 t lashing capacity per point at a minimum spacing of 480 mm) * 3 x 13.4 t lashing rings each side recessed in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal beams after the drop, 1 x above the centre axle next to the longitudinal beam) Low loader platform: * 3 x 13.4 t lashing rings each side on the outer frame (1 x beginning of the drop on the fifth wheel platform, 1 x beginning of the ramp slope, 1 x end of the ramp slope) * 2 x 10 t lashing rings each side (1 x between front wheel well and 1st axle, 1 x between 2nd and 3rd axle) * 3 x 5 t lashing rings each side bolted to the outer frame of the wheel wells (2 on the front wheel well, 1 on the rear wheel well) ----Excavator arm recess: * Extended excavator arm recess from end of last fixed axle through to steering axle up to rear crossmember, continuous with

Stanje: rabljeno, lastna masa: 10.900 kg, največja dovoljena obremenitev: 43.600 kg, skupna masa: 54.500 kg, konfiguracija osi: > 3 osi, prva registracija: 04/2025, dolžina tovornega prostora: 8.700 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 855 mm, velikost pnevmatike: 245/70 r17.5, barva: siv, Leto izdelave: 2025, obratovalna teža: 10.900 kg, Oprema: ABS, Gooseneck, rigid, center tube design: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Steel floor with anti-slip coating - Including perforated rail for aluminum approach ramps - 2" king pin - Manually operated BPW landing legs Dcsdpfx Abei Ai E Re Een - 550 mm long, 8° chamfer at end of gooseneck - Front wall including park position for rear wall, 400 mm high - Spare wheel holder mounted vertically on the front side of the gooseneck - 3 pairs of recessed lashing rings (LC 5,000 daN) in the loading area of the gooseneck - Aluminum side boards, 400 mm high, comprising 2x side boards each 3,150 mm long, and rear board with stanchions (galvanized) - Rectangular aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, center - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, left - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, right Loading platform, single-extendable: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Fixed section at front 700 mm - Steel plate floor with anti-slip coating - Chamfered transition between fixed part and deck for bridging rails and wheel recesses - Excavator trough including elongated holes for load securing (LC 1,500 daN), length approx. 3,850 mm - Prepared for hydraulic ramps (electrical supply) - Rails to widen up to 3,000 mm - 8° chamfered vehicle rear, 550 mm long - Slide system for easy mounting/dismounting of ramps - Continuous mud flap at the rear - 1 pair of lashing points LC 10,000 daN centrally on the loading area behind the gooseneck - 7 pairs of lashing points LC 10,000 daN in the outer frame of the loading platform - 6 pairs of stanchion pockets 100 x 50 mm in the outer frame of the loading platform - 1 pair of lashing points LC 10,000 daN centrally in the rear section of the loading platform - 1 pair of stanchion pocket rails approx. center of the loading area - 1 pair of stanchion pocket rails on the fixed part - 1 pair of stanchion pocket rails behind the last axle Ramps: - Hydraulic double-folding ramps, 2,750+1,500x800 mm - Larch wood surface - Operated by remote control (wired and wireless) - Quick-change ramp (dismantling system) Chassis: - Axle brand: BPW ECO Max - 2 ride heights - 4 axles @ 10 t (technically 12 t) - Twin tires 245/70 R17.5 - 2 x rigid axles and 2 x friction-steered axles - Reverse steering lock for friction-steered axles via reverse gear - Brake system by Knorr (according to EU standards with EBS-E) - Knorr TIM G2 (Trailer Information Module) - RSS (Roll Stability Support) stability control - Load-dependent lift axle on the first axle incl. starting aid (forced lowering of lift axle via TIM possible) Accessories: - 4 wheel chocks with holder - 2 pairs of warning panels 423 mm x 423 mm, with 2 position lights and socket for rotating beacon, steplessly adjustable up to 3,950 mm - Securing points on gooseneck and on loading platform (alternatively on ramp, if available) included - Plug-in bulkhead at the end of the excavator trough - Electrohydraulic unit for ramp operation - Ramp control by wireless remote - Hydraulic rear support legs for stabilization during loading - 1 pair of additional reversing lights at the rear, activated when reversing - Larch wood widening planks (option)

Stanje: novo, največja dovoljena obremenitev: 37.560 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 ton BPW axles * Start assist for shunting purposes on the first axle, activated via EBS (without truck-side installation) * Last axle is a trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle for maneuvering purposes from the driver’s cab via EBS (without truck-side installation) ----Suspension: * Air suspension with lift and lowering function as well as RtR valve ----Electrics / Lighting: * Smart-Board infotool mounted on trailer with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear * 2 additional LED reversing lights * 7-pin socket at rear for overlength lighting * Side marker lamps with indicator function * Tire pressure monitoring with display in the truck via EBS signal (without truck-side installation) ----General Attachments: * Side underrun protection * Support legs at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the front wall crossmember (without spare wheel) * Mechanically adjustable warning sign packages front and rear * Swing arm as a carrier for connecting lines from truck to semi-trailer ----Low Loader Platform: * 2nd king pin position * Gooseneck platform with 45° chamfered front corners and front-mounted toolbox made of galvanized, powder-coated sheet steel B = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm aluminum side boards (in desired RAL color) foldable and removable along the gooseneck platform * Rear wall, insertable, height 150 mm * Rear incline on the gooseneck platform to the low-bed approx. 700 mm long with checker plate covering and at the end a perforated strip for attaching aluminum approach ramps * Gooseneck platform with 50 mm clamped wooden planks, low-bed platform with 60 mm clamped wooden planks * Tread plate over axles Dcedpfx Ajykx Nksb Ejn * 9 mechanical extension panels to a total width of 3 m, not included in the rear incline (extension planks available with closed transverse stowage compartment under load floor) * Preparation for 3 storage recesses under the gooseneck platform for optional storage of aluminum approach ramps or planks for covering wheel recesses * Preparation for container locks on the swan neck ----Load Securing (LaSi Package): Gooseneck platform: * Perforated outer frame, 45° angled, with hole pattern for lashing devices (2 t lashing capacity per point with a minimum spacing of 480 mm) * 3 x 13.4 t lashing rings recessed into the floor per side (1 x on gooseneck platform, 1 x on longitudinal frame after the cranking, 1 x above middle axle next to longitudinal frame) Low-bed platform: * 3 x 13.4 t lashing rings per side at the outer frame (1 x start of gooseneck cranking, 1 x start of approach ramp, 1 x end of approach ramp) * 2 x 10 t lashing rings per side (1 x between front wheel recess and 1st axle, 1 x between 2nd and 3rd axle) * 3 x 5 t lashing rings per side screwed to outer frames of the wheel recesses (2 at front wheel recess, 1 at rear wheel recess) ----Excavator Arm Rest: * Extended excavator arm rest from end of last rigid axle over the steering axle to the end cross member, continuous with internal reinforcing profile approx. W = 770 mm x T rear

Stanje: novo, največja dovoljena obremenitev: 37.560 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Moving-off aid for shunting, connected to the first axle via EBS (no installation required on the truck side) * Last axle as self-steering trailing axle with electro-pneumatic lock * Trailing axle lock for shunting purposes, activated from the cab via EBS (no installation required on the truck side) ----Suspension: * Air suspension with lifting and lowering system, including RtR valve ----Electrics / Lighting: * Smart-Board infotool mounted on trailer with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear * 2 additional LED reversing lights * 7-pin socket at rear for overlength lighting * Side marker lights with indicator circuit * Tire pressure monitoring with display in the truck via EBS signal (no installation required on the truck side) ----General Attachments: * Side underrun protection * Landing gear at front, swing supports at rear of the chassis * Straight steel fenders * Spare wheel carrier in front of front wall crossmember (spare wheel not included) * Mechanically adjustable warning sign packages at front and rear * Swing arm as carrier for connection lines from truck to trailer ----Low Loader Deck: * 2nd kingpin position * Saddled platform with 45° chamfered front corners and front toolbox made from galvanized, powder-coated steel sheet (W = 2,480 x H = 500 x L = 665 mm) with folding lid * 400 mm high drop-down/removable aluminium sideboards (custom RAL color) on saddle platform * Removable 150 mm high rear wall * Rear inclined ramp of approx. 700 mm at the end of saddle platform to low-bed deck, fitted with checker plate and lashing bar for attaching aluminium approach ramps * Saddle platform with 50 mm tongued-and-grooved timber floor, low-bed platform with 60 mm tongued-and-grooved timber planks * Tread plate above axles * 9 x mechanical folding extensions to 3 m overall width, but not on rear ramp (extension planks included with lockable transverse storage compartment under load area) * Preparation for 3 ramp storage compartments under saddle platform for either aluminium ramps or timber planks for wheel trough covers * Preparation for container locks on the gooseneck ----Load Securing (LaSi Package): Saddle Platform: * Perforated external frame, angled at 45°, with hole pattern for lashing equipment (2 t lashing capacity per point, minimum spacing 480 mm) * 3 x 13.4 t recessed tie-down rings per side (1 on saddle platform, 1 on main longitudinal beams after the step, 1 above the center axle beside the beam) Low-bed Deck: * 3 x 13.4 t tie-down rings per side on outer frame (1 at the start of the gooseneck, 1 at the start of the rear ramp, 1 at the end of the ramp) * 2 x 10 t tie-down rings per side (1 between front wheel-well and 1st axle, 1 between 2nd and 3rd axle) * 3 x 5 t tie-down rings per side, bolted to the outer frame of wheel wells (2 at front, 1 at rear wheel well) Dcedpfx Aeykx Nqob Een ----Digger Arm Rest: * Extended digger arm rest from end of last fixed axle over steering axle to end crossmember, continuous with internal reinforcement profile, approx. W = 770 mm x D at rear

Stanje: rabljeno, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, prva registracija: 09/2017, * SAF osi * Kolesni izrezi * Hidravlične nakladalne rampe, nastavljive po širini * Zračno vzmetenje * Možnost razširitve * Lastna teža: 11.020 kg ----Interna številka vozila: 11010----Napake in vmesna prodaja pridržane. WhatsApp podpora na voljo! Za vprašanja o vozilu ali dodatne informacije nam pišite udobno preko WhatsAppa Dcjdpjwta Alefx Ab Eon WhatsApp nemško, angleško -- WhatsApp nemško, angleško, arabsko

Stanje: rabljeno, največja dovoljena obremenitev: 42.500 kg, skupna masa: 60.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/2022, with 12 axles, divided, hydraulically suspended, with hydromechanical forced steering, with rear taper and drive-on ramps STZ-L Gooseneck - robust welded steel construction - formed loading area 3,950 x 2,480 mm incl. tapered rear section Dodpfxow Etd Ts Ab Eecn - hydromechanical forced steering (dual-circuit steering) - turntable-mounted king pin plate with replaceable 2 or 3.5 inch king pin and adjustable steering wedge - fifth wheel load 24 t - rear turning radius: 2,600 mm Loading Deck - stepped outer beams 4,630 mm, 420 mm deep, providing a loading height of 470 mm or 830 mm with decking installed - extendable by 2,053 mm - includes aluminium bridging rails for creating a flat surface - excavator arm recess at rear of chassis: 4,900 mm long, 880 mm wide, 480 mm deep - chassis length at rear: 4,900 mm including 500 mm rear taper, loading height 890 mm - pair of wheel recesses in lower loading area - hydraulically suspended 3-axle chassis - divided Gigant axles with 600 mm stroke Rear of Vehicle - design: 500 mm rear taper - hydraulic rear support Drive-on Ramps - 2-piece ramps, length: 2,850 + 1,850 mm, width: 800 mm - rubber-coated surface with climbing strip Brake System - dual-line full air brake system with diaphragm brake cylinders - automatic load-dependent brake (ALB) - automatic rod plates (AGS) - parking brake operated via spring-loaded cylinders - ABV brake system Special Equipment - radio remote control for steering and ramp operation - central lubrication system Technical Data Gooseneck Loading area (LxW): 3,950 x 2,480 mm Loaded saddle height: 1,300 mm Loading Deck Loading area (LxW): 10,030 x 2,850 mm, extendable by 2,053 mm Stepped outer beams: 4,630 mm long plus 2,053 mm extension Centre beam: 980 mm Excavator arm recess: 4,900 mm long, 880 mm wide, 480 mm deep Steering 1st to 3rd axle with hydromechanical forced steering (dual-circuit steering)

Stanje: rabljeno, skupna masa: 47.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2004, naslednji pregled (TÜV): 08/2026, * Müller Mitteltal TS3 nizkopodni polpriklopnik * Prva registracija: 11/2004 * 3 osi * Zračno vzmetenje * Gigant osi * Hidravlične dolge rampe, pomične in zložljive * Razširitve iz 2,50 m na 3,0 m širina nakladalnega prostora * Nakladalna dolžina: 8,50 m pri nakladalni višini 0,85 m * Nakladalna dolžina na vratu: 3,40 m pri nakladalni višini 1,50 m * Podpore * Neto teža: 10.260 kg * Tehnično dovoljena skupna masa: 47.000 kg * TÜV veljaven do: 08/2026 * Tehnični pregled do: 02/2026 Dcsdpfx Abow Tgkbo Esn

Stanje: zelo dobro (rabljeno), Funkcionalnost: popolnoma funkcionalen, moč: 205 kW (278,72 KM), vrsta goriva: dizel, skupna masa: 20.000 kg, Leto izdelave: 2025, obratovalne ure: 400 h, Oprema: UVV varnostni pregled, nastavljiva roka, računalnik na krovu, We are pleased to offer you a WERT Phantom dual-shaft shredder. - used - Drive – Engine: CAT-C7 – 285 HP Hydraulics: Bosch-Rexroth Torque / Gearbox: 240,000 Nm Discharge height: 3,100 mm Discharge conveyor: 1,000 mm wide Diesel tank: 380 l Hydraulic tank: 120 l Shaft length: 1,500 mm Dedsw T Stbepfx Ab Eocn Shaft diameter: 650 mm Magnet weight: 1.1 t Total weight: 18.5 t Dimensions (L x W x H): 9.2 x 2.3 x 2.55 m Dual-shaft shredder – ready for the future of recycling technology. A touch of innovation in the shredding industry. Driven by the vision to develop a shredder capable of processing stone, minerals, concrete as well as waste wood, green waste, root wood, domestic and commercial waste, paper, or light scrap, we’ve succeeded in creating the PHANTOM. This multifunctional shredder features a revolutionary quick-change shaft system and a tool reversal system. These systems allow for fast, straightforward, and low-maintenance replacement of the tool shafts, tailored to each specific application. In manufacturing, the highest quality standards – "Made in Germany" – and incredibly user-friendly operation are top priorities to ensure maximum performance and best possible efficiency. If you have any questions, feel free to contact us! The contents of our offers have been created with the greatest care. However, we cannot guarantee the accuracy, completeness, or timeliness of the information and prices provided.

Stanje: rabljeno, največja dovoljena obremenitev: 23.000 kg, skupna masa: 36.000 kg, konfiguracija osi: 3 osi, prva registracija: 04/2025, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.550 mm, skupna širina: 2.550 mm, Leto izdelave: 2025, Oprema: ABS, GVN 3GVN29 PREŠIROKA OPLOŠČENICA?PRIKLJUČEK ZA VILICE?HIDRAVLIČNA RAMPA ----ZGODOVINA VOZILA * NOVO VOZILO * VIDEO NA VOLJO NA ZAHTEVO OPREMA VOZILA TEHNIČNA DATOTEKA IN SPECIFIKACIJE VOZILA, VRSTA VOZILA: * GVN PRIKLJUČEK – 3-OSNA EVROPSKA MODELNA VRSTA TRGOVSKO IME: * 3GVN29 ----PODATKI O TEŽI MASA V VOZNI STANJU * 13.000 KG RAZPOREDITEV TE TEŽE NA OS 1. OS: 3.653 KG 2. OS: 3.653 KG 3. OS: 3.653 KG DEJANSKA TEŽA VOZILA * 13.000 KG TEHNIČNO DOVOLJENA MAKSIMALNA BRUTO TEŽA * 58.000 KG TEHNIČNO DOVOLJENE MAKSIMALNE OSNE OBREMENITVE 1. OS: 12.000 KG 2. OS: 12.000 KG 3. OS: 12.000 KG TEHNIČNO DOVOLJENA MAKSIMALNA TEŽA NA OSNIH SKUPINAH 1. SKUPINA: 36.000 KG MAKSIMALNA BRUTO TEŽA, PREDVIDENA ZA REGISTRACIJO * 35.500 KG MAKSIMALNE OSNE OBREMENITVE, PREDVIDENE ZA REGISTRACIJO 1. OS: 8.000 KG 2. OS: 8.000 KG 3. OS: 8.000 KG MAKSIMALNA TEŽA NA OSNIH SKUPINAH, PREDVIDENA ZA REGISTRACIJO 1. SKUPINA: 24.000 KG TEHNIČNO DOVOLJENA MAKSIMALNA STATIČNA TEŽA NA TOČKI PRIKLOPITVE * 22.000 KG TEHNIČNE GLAVNE DIMENZIJE (COC) ? SKUPNA DOLŽINA 13050 MM ? DOLŽINA OPLOŠČENE POVRŠINE 9200 MM ? ŠIRINA VOZILA 2550 MM ? SKUPNA VIŠINA 3000 MM ? VIŠINA PLATFORME PRIBLIŽNO 910 MM ? ŠTEVILO OSI 3 ? VELIKOST PNEVMATIK 235/75 R17.5 ? VZMETENJE VZMETENJE NA ZRAK ? BARVA RAL 5011 ----SEZNAM OPREME ? PODALJŠANO VLEČNO OKVIRJE ? FIKSNO VLEČNO OKVIRJE ? JEKLENA SPREDNJA STENA ? 2 STRANSKI VRATA IZ JEKLA, ODSTRANLJIVA ? 1 ZADNJA VRATA IZ JEKLA, ODSTRANLJIVA ? PROSTOR ZA PRTLJAGO NA SPREDU ? PROSTOR ZA PRTLJAGO NA SPREDU POD PRIKLJUČKOM ? OPLOŠČENA POVRŠINA NA PRIKLJUČKU OPLOŠČENA PLATFORMA ? VISOKO TRDNA JEKLA S355 ? ROBOVI PLATFORME OBROBJENI Z LESA ? POVRŠINA POKRITA Z JEKLENO PLOŠČO ? 14 STRANSKIH NADALJŠKOV, PO 230 MM ? 14 KOVANSKIH JEKLENIH ZAPORNIC ZA PRITOŽITEV, PO 16 TON ? IZTEZLJIVA PLOŠČA ZA PREŠIROKE TERE ? PREŠIROKI PRAG ? OPOZORILNA TABLA ZA PREŠIROKE TERE ? TOČKE PRITOŽITVE ? DODATNA OPORA ? INDIKATOR TLAKA OSI IN VZMETENJE ? 3 OSI ? OSI OSMAN KOC, IDENTIČNE BPW ? USMERJALNA OS 3. OS ? DVIŽNA OS 1. OS ? DVOMENJE NA VSEH OSIH ? VZMETENJE, POPOLNO VZMETENJE NA ZRAK NA VSEH OSIH ? DVIŽNA OS 1. OS, BOBNOVNO ZAVORNO SISTEM ZAVORNI SISTEM ? SISTEM EBS WABCO ELEKTROPNEVMATSKI, V SKLADU Z EC-NORMO ? AVTOMATSKI SISTEM ZA SAMODEJNO PORAVNAVO USMERJENE OSI PRI VOŽNJI VZAD ? BOBNO ZAVORNO SISTEM NA VSEH OSIH PNEVMATIKE IN PLATIŠČA ? PNEVMATIKE 235/75 R17.5 ? NADOMESTNA PNEVMATIKA DA ? KOLA 12 ? MAKSIMALNA HITROST 80 KM/H ? PLATIŠČA 6.75X17.5, JEKLO, SREBRNO-SIVA ? NADOMESTNO KOLO NA VOLJO BARVANJE ? 2 SLOJA EPOKSIDNEGA TEMELNEGA LAKA, PO 100 MIKRONOV ? MINIMALNO 100 MIKRONOV 2K AKRILNEGA LAKA ? BARVA RAL 5011 ELEKTRIKA IN OSVETLITEV ? 24-VOLTNI SISTEM, V SKLADU Z EC-NORMO ? NEPREDUŠNI IN ODPORNI PRIKLJUČKI ? STRANSKE IN POZICIJSKE LUČI ? 6 ZADNJE LUČI, 3 FUNKCIJE ? 2 LUČI ZA VOŽNJO VZAD IN DELOVNE LUČI ? 2 SMEROKAZA ? 2 LUČI ZA REGISTRACIJSO ŠTEVILKO ? 1 OKROGEL ROTIRAJOČA LUČ ? 2 TRIKOTNIKOV REFLEKTORJEV ? REFLEKTIRAJOČI TRAMOVI IN E-OZNAČBA ? TRAILER LIGHT SYSTEMS ? ROTIRAJOČI ZADNJI ODSEVNIKI RAMPA ? TRAJNO NAMEŠČENE HIDRAVLIČNE RAMPE ? HIDRAVLIČNO STRANSKO POMIK, LEVO IN DESNO Dcjdpfxsw Dlqie Ab Eon ? PODPIRALA 24 TON DINAMIČNO, 50 TON STATIČNO OMS ? ROČNE PODPORE ZA RAMPE ? PRIKLJUČEK ZA HIDRAV

Stanje: novo, največja dovoljena obremenitev: 39.280 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profil 30,0: ----Zavora: * Wabco EBS-E (električni zavorni sistem) * Naprava za sprostitev v primeru zasilnega stanja za cilindri z zračnim pomnilom * Bobnaste zavore ----Osi: * 3 x 11 ton BPW Eco Plus osi * zadnja os s prilagodljivim nagibom in elektropnevmatskim sistemom za zaklepanje krmiljenja ----Vzmetenje: * Zračno vzmetenje z dvigalom in spuščanjem ter ventilom za vzdrževanje višine ----Elektrika / Osvetlitev: * Sistem za nadzor tlaka v pnevmatikah (TPMS) * Nadzorna plošča Smartboard, nameščena na prikolici, služi kot informacijsko orodje in vsebuje tipalnike za prikaz skupne obremenitve osi * 15-polni vtič za elektriko * LED-osvetlitvena oprema 12 / 24V * LED-okrogla luč (odstranljiva) zadaj levo ----Splošni dodatki: * stranski zaščitni sistem * dvižna oprema spredaj in mehanske podpiralne noge zadaj na šasiji * ravne jeklene blatnike * nosilec za rezervno kolo pod šasijo, na desni strani ----Površina za nizko nosljivost: * Patforma za sedelno prikolico s 45-stopinjsko nagnjenimi sprednjimi robovi in predalom za orodje na sprednji strani, izdelan iz pocinkane jeklene pločevine, B = 2.480 x V = 500 x D = 665 mm z pokrovom * stranske aluminijaste strani na platformi za sedelno prikolico, 400 mm (RAL 9010, čista bela), z možnostjo odpiranja in odstranjevanja * zadnja stena, višina 150 mm * zadnji naklon na platformi za sedelno prikolico za nizko nosljivost, dolžina približno 700 mm * platforma za sedelno prikolico z 50 mm debelimi lesenimi deskami ter platforma za nizko nosljivost z 60 mm debelimi lesenimi deskami * diamantna pločevina nad osmi ----Razširitve: * 8 x mehanske razširitve, ki se odpirajo, na skupno širino 3 m, vendar ne na zadnjem naklonu (razširitvene deske so na voljo in jih je mogoče shraniti na platformi za sedelno prikolico) * mehanski sistem za nastavitev opozorilnih tabel spredaj in zadaj ----Komplet za pritrditev tovorja (Las-paket): * na platformi za sedelno prikolico 2 x 6,3 t pritrdišča za pritrditev tovora, stransko 3 x 5 t pritrdišča za pritrditev tovora v zunanjem okvirju * v platformi za nizko nosljivost stransko 2 x 13,4 t pritrdišča za pritrditev tovora ter 4 x 10 t pritrdišča za pritrditev tovora, ki se lahko zasukajo in spuščajo, vstavljena v zunanjem okvirju * stransko 2 x 6,4 t pritrdišča za pritrditev tovora ter zadaj 1 pritrdišče za pritrditev tovora v nosilcu za roko bagra * 2 x zaklepna naprava za kontejnerje neposredno za upognjenim delom v platformi za nizko nosljivost ----Nosilec za roko bagra: * Nosilec za roko bagra od konca zadnje fiksne osi do krmilne osi do končnega nosilca, celoten z notranjimi ojačitvenimi profili, dolžina približno L = 2.450 x Š = 770 mm x G = 270 mm ----Rampe: * mehanske, enodelne, vroče pocinkane hidravlične rampe, približno 3.000 x 720 mm (mehansko nastavljive v stranski smeri) * nadzorna enota, 4-kanalna, za poznejšo nadgradnjo stranke z hidravličnim sistemom za premik ramp * zunanja deska na rampi je iz 50 mm trdega lesa * protizdrsne letve na zunanjem okvirju rampe in na naklonu ----Hidravlika: * Hidravlični razdelilnik na prikolici (pri hidravlični moči črpalke na tovornjaku nad 40 l do 120 l/min) ----Dimenzije tovornega prostora: Dsdpfx Absl Tnvgo Eocn * Površina platforme za sedelno prikolico: približno 3.935 x 2.480 mm * Površina za nizko nosljivost: približno 8.500 x 2.520 mm * Višina tovornega prostora brez obremenitve: približno 910 mm (vključno z 860 mm naklonom) ----Višina sedla: * približno 1.220 mm (primeren za 2-osne in 3-osne SZM) ----B