Polpriklopnik z nizko nakladalno ploščadjo

MEUSBURGER MTS3 12 t Achsen ,ausziehbar, gelenkt ,

Stanje: novo, lastna masa: 17.500 kg, največja dovoljena obremenitev: 43.500 kg, skupna masa: 61.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.750 mm, višina nakladalnega prostora: 400 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - For tractor units: 6x4 or 8x4 Lowbed: - Lowbed with external beams, extendable version, "SUPER LOW" design, approx. 7,550 mm long - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking device - Service lines are protected within the extendable beams and automatically adjust to the lowbed length Rear Undercarriage: - Rear chassis with closed outer frame, checker plate cover, and continuous prism-shaped excavator trough approx. 1,450/900 x 505 mm, open at the rear - 2 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame Axles and Tires: Bjdpfxeh Hm Ths Al Helg - "PENDULUM AXLE", all axles hydro-mechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 / 3PMSF Included Accessories: - Prepared for bolt-on container positioning for 1x 20ft or 1x 40ft container on the outer beams - 2" kingpin - Galvanized steel front wall approx. 400 mm high - One spare wheel with holder - At the galvanized front adapter bar yellow-red air couplings - 4 wheel chocks - Remote rear steering from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Hydraulic line connections from gooseneck to lowbed with multi-coupling instead of screw coupling - Electro-hydraulic power pack - White reflective tape to EU specifications on sides, extension, and rear red - 2 wooden blocks 500x250x200 mm - European reflective plates (red-yellow) on the trailer rear - At the gooseneck and rear wall left and right each a bracket for warning boards including socket - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 - Load gauge for determination of axle loads including load diagram - On the gooseneck, plug-in ALU side and rear boards approx. 2,000 x 400 mm - The rear galvanized insert posts are removable (body length approx. 2,120 mm) - Separate air connection for air gun on the gooseneck - Duomatic air coupling from gooseneck to lowbed - Rear upper section of gooseneck closed with removable cover - 1 pair of steel ramps to bridge the lowbed's pick-up hooks - Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm - Wireless remote control for rear steering in addition to cable remote, with signal lights at receiver for single-track monitoring - 6 pairs of threaded blocks between lashing rings under the top chord on the outer beams for mounting screwable RUD rings VLBG-4 - 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading bed - Foldable extensions, approx. 230 mm per side - Loading area features a painted sand layer for anti-slip protection - Dipper stick trough of rear chassis closed at front and rear with plug-in plates - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - alu 15%)

Stanje: novo, največja dovoljena obremenitev: 50.400 kg, skupna masa: 65.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment specification. Full specification available on request. GOOSENECK * Gooseneck in SNT design to optimize platform length, approx. length 3,700 mm, with rear bevel of approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX at the front connection rail with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, except for hydraulic winches * 1 pair of detachable ALU side walls, approx. 400 mm high, anodized finish * 1 detachable ALU rear wall, approx. 400 mm high, anodized finish * Over the gooseneck, approx. 40 mm thick hardwood flooring, over the king pin with checker plate covering * 2-inch king pin * Mount at the rear of the gooseneck for ALU drive-on ramps * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) LOAD PLATFORM * Extendable load platform, approx. length 8,800 mm, with rear bevel approx. 500 mm x 10° * Recess in platform and rear bevel for accommodating an excavator dipper stick, approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st axle self-steering, all other axles hydro-mechanically forced steered * 1st axle with electromagnetic reversing lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with lift and lower valve * Tires: 235/75 R 17.5 3PMSF twin tires * Mechanical landing legs with 2-speed gearbox and crank, JOST Modul B - static test load = approx. 50,000 kg * Platform with continuous and between-axles interrupted 50 mm thick hardwood flooring (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable galvanized side extensions by approx. 230 mm each side (without wooden planks) * Wheel wells with square climbing strips, approx. 15 x 15 mm in front of the axles, continuous opening up to the cross member of the gooseneck, approx. 700 x 410 mm (W x D) * ALU covers for the wheel wells, usable as bridging elements for the extension OR as width extension planks * Lockable aluminium elements on the extension tubes of the side extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel wells with square climbing strips, approx. 15 x 15 mm between the 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * ALU covers for the wheel wells, usable as bridging elements for the extension OR as width extension planks * Lockable aluminium elements on the extension tubes of the side extensions * 1 pair of mechanical rear supports Blodpfxetx Nwns Al Hog * Remote steering from front and rear via cable remote control, with single-track monitoring of the axles, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-part steel ramps, type: DR-15/60-900-4350-KG-HV-M, approx. length 4,350 mm and width approx. 900 mm * Hydraulically folding ramp tips * Ramps hydraulically adjustable individually by approx. 235 mm outward and approx. 215 mm inward * Super Grip rubber surface approx. 25 mm and steel surface approx. 5 mm as additional

Stanje: zelo dobro (rabljeno), konfiguracija osi: 2 osi, prva registracija: 03/2015, dolžina tovornega prostora: 134.450 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 480 mm, vzmetenje: hidravlika, Leto izdelave: 2015, Oprema: ABS, = Dodatne možnosti in oprema = - Centralno mazanje = Dodatne informacije = Konfiguracija osi Vzmetenje: hidravlično vzmetenje Zadnja os 1: Max. obremenitev osi: 12.000 kg; Krmiljena Zadnja os 2: Max. obremenitev osi: 12.000 kg; Krmiljena Teže Lastna teža: 12.660 kg Nosilnost: 34.340 kg Skupna dovoljena masa: 47.000 kg Funkcionalno Višina nakladalne površine: 48 cm Blodpfx Ajvtc Aiel Hog Izvlečna nadgradnja: Da Stanje Tehnično stanje: zelo dobro Vizualno stanje: zelo dobro Finančne informacije Cena: Po dogovoru Dodatne informacije Za več informacij se obrnite na Davida F Middelmana.

Stanje: rabljeno, lastna masa: 10.900 kg, največja dovoljena obremenitev: 43.600 kg, skupna masa: 54.500 kg, konfiguracija osi: 3 osi, prva registracija: 04/2025, dolžina tovornega prostora: 8.700 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 855 mm, velikost pnevmatike: 245/70 r17.5, barva: siv, Leto izdelave: 2025, obratovalna teža: 10.900 kg, Oprema: ABS, Gooseneck, rigid, center tube design: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Steel floor with anti-slip coating - Including perforated rail for aluminum approach ramps - 2" king pin - Manually operated BPW landing legs - 550 mm long, 8° chamfer at end of gooseneck - Front wall including park position for rear wall, 400 mm high - Spare wheel holder mounted vertically on the front side of the gooseneck - 3 pairs of recessed lashing rings (LC 5,000 daN) in the loading area of the gooseneck - Aluminum side boards, 400 mm high, comprising 2x side boards each 3,150 mm long, and rear board with stanchions (galvanized) - Rectangular aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, center - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, left - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, right Loading platform, single-extendable: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Fixed section at front 700 mm - Steel plate floor with anti-slip coating - Chamfered transition between fixed part and deck for bridging rails and wheel recesses - Excavator trough including elongated holes for load securing (LC 1,500 daN), length approx. 3,850 mm - Prepared for hydraulic ramps (electrical supply) - Rails to widen up to 3,000 mm - 8° chamfered vehicle rear, 550 mm long - Slide system for easy mounting/dismounting of ramps - Continuous mud flap at the rear - 1 pair of lashing points LC 10,000 daN centrally on the loading area behind the gooseneck - 7 pairs of lashing points LC 10,000 daN in the outer frame of the loading platform - 6 pairs of stanchion pockets 100 x 50 mm in the outer frame of the loading platform - 1 pair of lashing points LC 10,000 daN centrally in the rear section of the loading platform - 1 pair of stanchion pocket rails approx. center of the loading area - 1 pair of stanchion pocket rails on the fixed part - 1 pair of stanchion pocket rails behind the last axle Ramps: - Hydraulic double-folding ramps, 2,750+1,500x800 mm - Larch wood surface - Operated by remote control (wired and wireless) - Quick-change ramp (dismantling system) Blodpfx Alji Ai E Rj Hog Chassis: - Axle brand: BPW ECO Max - 2 ride heights - 4 axles @ 10 t (technically 12 t) - Twin tires 245/70 R17.5 - 2 x rigid axles and 2 x friction-steered axles - Reverse steering lock for friction-steered axles via reverse gear - Brake system by Knorr (according to EU standards with EBS-E) - Knorr TIM G2 (Trailer Information Module) - RSS (Roll Stability Support) stability control - Load-dependent lift axle on the first axle incl. starting aid (forced lowering of lift axle via TIM possible) Accessories: - 4 wheel chocks with holder - 2 pairs of warning panels 423 mm x 423 mm, with 2 position lights and socket for rotating beacon, steplessly adjustable up to 3,950 mm - Securing points on gooseneck and on loading platform (alternatively on ramp, if available) included - Plug-in bulkhead at the end of the excavator trough - Electrohydraulic unit for ramp operation - Ramp control by wireless remote - Hydraulic rear support legs for stabilization during loading - 1 pair of additional reversing lights at the rear, activated when reversing - Larch wood widening planks (option)

Stanje: novo, največja dovoljena obremenitev: 67.200 kg, skupna masa: 85.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete inventory of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment features. Full equipment details upon request. GOOSENECK * Gooseneck in SNT design for optimized loading platform length, approx. 3,700 mm long, with a rear chamfer approx. 1,000 mm x 10° * For tractor units: 6x2, 6x4, and short 8x4 * Plug-in steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for controlling hydraulic functions, excluding hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in ALU sideboards, approx. 400 mm high, anodized finish * One plug-in ALU rearboard, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood flooring above the gooseneck, checker plate flooring above the king pin * 3.5 inch king pin * Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide * Round NATO socket on the front connection bar (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow control, incl. bracket for suspension of supply lines (Faymonville couplings) * 2 pairs of stake pockets sunk into the gooseneck, for plug-in stakes approx. 100 x 50 mm LOADING DECK * Extendable loading deck, length approx. 11,000 mm, rear chamfer approx. 500 mm x 10° Bledpsrgzv Nsfx Al Hsg * Pneumatic locking with conical locking bolt and reinforced lock positions, supply lines are routed protected in the extendable beams and automatically adjust to the respective platform length * BPW axles and suspension, 1st axle steerable, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Tyres: 235/75 R 17.5 3PMSF, twin tyres * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B - static test load = approx. 50,000 kg * Continuous 50 mm thick hardwood flooring on the loading deck, interrupted between the axles (increases coefficient of friction) * Slotted holes for attachable and re-positionable bridging elements: - on the fixed section behind the gooseneck - at the front of the loading area * 1 sliding intermediate table, approx. 500 mm wide, for the extension tube with large cross-section, with checker plate flooring, slotted holes front and rear for attachable and repositionable bridging elements * 1 pair of recessed horizontal lashing rings at the front of the fixed platform section (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the deck, fold-out to the outside (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering operated from both front and rear via cable remote control, with axle tracking control, no installation in the tractor unit * 1st axle with automatic lift-axle function and start-up aid according to EU Directive 2021/535 * Under the gooseneck and on the rear cross member, one 7-pin socket each on left and right, with bracket for warning signs * Painted sand coating on the outer frame of the platform as well as on the checker plates of the platform and in the transition area between the loading deck

Stanje: novo, največja dovoljena obremenitev: 31.500 kg, skupna masa: 42.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2025, Oprema: ABS, Priekaba Wiese ar trijų ašių važiuokle, kėlimo stalu ir atverčiamu galu. Idealiai tinka šakinių krautuvų ir (arba) darbo platformų pervežimui. Techninės specifikacijos. 3 x 10 t ašys Pakeliama ašis Valdoma ašis su „Smart Steering“ (vairavimas į priekį ir atgal) Išorinio rėmo važiuoklė su nuolydžiu Galinė konstrukcija, tinkama 18 t, pritaikyta 2- ir 3-ašių vilkikams Hidraulinis kėlimo stalas reguliuojamas 3 pozicijose Atverčiamas galas su hidrauliniais išstumiamais elementais, tinkamas naudoti kaip užvažiavimo rampos, pervažiavimo rampos arba kaip pakrovimo platforma (Bendro ilgio sumažinimas pakėlus galą vertikaliai) Nuotolinis valdymas rampoms ir kėlimo stalui Priekinė sienelė Grotelinis grindų paviršius Daug tvirtinimo taškų „SmartBoard“ sistema Centrinė tepimo sistema Blodpsvw Hmtefx Al Heg Plieninė konstrukcija, cinkuota ir nudažyta Galima įsigyti daugybę papildomų pasirinkimų, pvz.: - Gervė - Įrankių dėžė ant priekabos pakopos - Aliuminiai ratlankiai Daugiau informacijos pagal užklausą.

Stanje: novo, lastna masa: 15.550 kg, največja dovoljena obremenitev: 47.450 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimization of loading platform length, length approx. 3,700 mm - Rear gooseneck with bevel approx. 1,000 mm x 10° Loading Platform: - Extendable loading platform, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° - A recess in the loading platform as well as into the bevel for accommodating the excavator dipper stick - Pneumatic locking with conical locking bolts and reinforced lock positions - Hardwood covering on the loading platform bevel Ramps: - 1 pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm - Ramps with hardwood covering - Hydraulically folding ramp tips - Ramps can be hydraulically shifted individually approx. 235 mm outward and approx. 215 mm inward - Square climbing cleats 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, 1st axle lift-steered, all other axles forced-steered with hydromechanical system - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, activated via reverse gear and manually Bledsk Aht Uopfx Al Hog - Air suspension with raising and lowering valve - Tyres 235/75 R 17.5, twin tires - TPMS tire monitoring system compliant with ECE R141 - TPMS sensors installed in all wheels including spares Accessories included: - Removable steel front wall, approx. 400 mm high - 3kW electro-hydraulic power pack for hydraulic operations, excluding hydraulic winches - Parking position on gooseneck for warning boards when not in use - 1 spare wheel - On the gooseneck: 1 pair of removable side aluminium drop sides, approx. 400 mm high, anodised - On the gooseneck: 1 removable rear aluminium drop side, approx. 400 mm high, anodised - Above the gooseneck: approx. 40 mm thick hardwood floor, chequer plate above king pin - 2" king pin - Guide plate on gooseneck for fifth wheel, approx. 500 mm wide - 4 wheel chocks - Mechanical landing gear with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - 1 intermediate table, approx. 300 mm wide - Extensions (galvanised) extendable by approx. 230 mm per side - Wheel recesses with square climbing cleats - ALU covers for the wheel recesses - 1 pair of mechanical rear supports - Remote steering at front and rear via cable remote control, with single track monitoring of axles - 1st axle with automatic lift axle function - Central lubrication system with 1 BEKAMAX brand pump - Radio remote control for remote steering, additionally to cable remote, with 2 indicator lights on the receiver as single track monitoring - Wabco Smart Board System - 4 warning boards, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for revolving beacon

Stanje: novo, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, 3-axle MULTIMAX PLUS low-bed semi-trailer, air-suspended and hydraulically forced-steered axles. Technical Data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Maximum speed: 80 km/h (legal) Gross vehicle weight: 49,500 kg 31,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Bljdoizu Ntepfx Al Hjg Turning radius king pin to rear approx.: 2,100 mm Coupling height loaded approx.: 1,205 mm Loading platform length approx.: 9,600 mm Extendable by approx.: ? Loading platform width approx.: 2,540 mm Load height at max. load approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle spacing: 1,360 mm Gross weight dependent on fifth wheel load: Yes Special permit required if exceeding country-specific legislation: Technical Description Gooseneck: Gooseneck in SNT design to optimize loading platform length, length approx. 3,900 mm, rear with bevel of approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor units: 4x2 and 6x2. Loading platform: Loading platform approx. 9,600 mm in length with rear bevel approx. 900 mm x 6°. Loading area after gooseneck hydraulically liftable and lowerable, length approx. 3,000 mm, load capacity up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS One pair of two-piece AXS steel ramps, approx. 4,920 mm long and approx. 900 mm wide. Open grating surface. Hydraulically folding ramp tips. Ramps individually hydraulically adjustable by approx. 235 mm outward and approx. 365 mm inward. Maximum load and ramp angle according to technical datasheet: C470319 Maximum gradient angle with lowered loading area: 9° Axles and Suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg Air suspension with lifting and lowering valve. Axle tools. Tyres: 235/75 R 17.5 3PMSF twin tyres. Brand at our discretion Load index 143/141J (144/144F) Brake System: WABCO EBS-E brake system according to EU regulations. No connecting cable to the tractor unit included. Lighting System: 24V lighting system in "ASPÖCK-NORDIK full LED" version according to EU regulations. (ASS 3) Metallisation: Complete HRM metallisation (High Resistance Metallisation) Entire steel structure shot-blasted, then hot-finished with ZINACOR 850 (Zinc 85% - Aluminium 15%). 6-Coat Paint Treatment: Entire steel structure shot-blasted after welding. 1 coat zinc-based primer, 1 coat adhesion primer. Topcoat consisting of 2 layers of 2K paint (acrylic) in a single RAL shade of choice, followed by cavity sealing with special wax. Rims in silver. Multi-colour and special coatings available at extra charge. Steel Construction: High-strength fine-grain steel structure. Steel grades: S355J2+N/S355MC (min. yield strength 355MPa) S690QL/S700MC (min. yield strength 690MPa) Welders certified to DIN-EN 287-1. MAG-welding process to EN ISO 4063. Shielding gas M21 according to EN ISO 14175 Front bulkhead made of steel, detachable, approx. 400 mm high Connector strip for supply lines to the tractor unit, mounted at the height of the outer frame profile. ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pin connection according to ISO-12098 If your pin configuration deviates from the ISO standard, please inform us. Anderson socket at the front connection strip. Rema 78051-00 & Amp. 150 V. Cable for supplying the electro-hydraulic power unit and/or

Stanje: novo, največja dovoljena obremenitev: 38.100 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.100 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5 3PMSF, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer of approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading platform: 5 pairs of fold-out lashing rings 3 pairs of fold-out lashing rings 1 pair of horizontal lashing rings at the front of the loading area Cut-outs in the outer frame of the loading surface for hooking in tension belts Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Landing legs: JOST landing legs with 2-speed gears for a 24 t lifting capacity Axles and tyres: BPW axles, two axles are fixed, two axles are self-steering, air-suspended, with drum brakes, with lift/lower function The self-steering axles come with an electro-magnetic reverse lock, which is activated via reverse gear or manually Axle toolkit Tyres: 205/65 R17.5 3PMSF Brake system: WABCO brake system according to EU regulations with EBS-E Steel construction: Steel structure made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Electrical equipment: Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK lighting ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO Bjdpfxjtphtms Al Hjlg Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component zinc dust primer High-quality single-colour 2-component top coat in MB 7350 Novagrau No metallic paint possible Rear section metallized and painted in RAL 9010 Accessories included: 1 spare wheel 205/65 R 17.5 TPMS tyre pressure monitoring system acc. to ECE R 141 At the galvanized front connection strip yellow-red air couplings 4 wheel chocks with holder on front wall Bracket at rear of gooseneck for ALU access ramps Galvanized folding supports under the chamfer of the loading surface Mount for a revolving beacon at the rear of the trailer Height-adjustable curtain structure Galvanized front wall with a tension mechanism for the sliding curtains Height-adjustable by approx. 400 mm "EDSCHA" brand roof, sliding forward on ALU roof beam profiles, bolted to the front and rear wall In the loading surface, 3 pairs of sliding stakes Superstructure at rear hydraulically extendable to left and right by approx. 750 mm Sliding roof with upward swinging portal carrier Sliding tarp with 700 mm reserve length, with tension straps at intervals of approx. 600 mm Height to top edge of superstructure approx. 3,960 mm Journeys with the sliding roof open are not permitted and will damage the tarp Mounting rail for ALU access ramps at the rear of the vehicle At the gooseneck and at the rear panel left and right, each with a mount for warning signs incl. socket A mud flap at the rear of the trailer European reflector plates at the rear of the trailer 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading area Lifting axle on the front axle controlled by TEBS E depending on current axle load and load status Rear structure with closed ALU double-wing doors A sanded, anti-slip paint layer on the checker plates on the gooseneck and on the loading surface BEKAMAX centralized lubrication system with standard grease NLGI-2 and a removable guard around the pump Speed stickers 80 km/h on rear and both sides Load manometer for axle load determination including load chart

Stanje: dober (rabljeno), Funkcionalnost: popolnoma funkcionalen, skupna masa: 57.600 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.240 mm, širina tovornega prostora: 2.750 mm, višina nakladalnega prostora: 945 mm, barva: modra, Leto izdelave: 2008, Na voljo imamo dva taka nizkopodpohodna priklopnika. Proizvajalec: Goldhofer Tip: STZ-VKL 3-34/80 A Leto izdelave: 2008 Skupna masa: 54.000 kg Lastna masa: 21.000 kg Nosilnost: 33.000 kg Skupna dolžina kompozicije: 20.000 mm (maks. teleskopsko 24.200 mm) Nakladalna površina (d x š): 7.300 mm x 2.750 mm (teleskopsko do 4.200 mm) Bljdoxc U Nvjpfx Al Hog Pnevmatike: 235/75 R 17,5 Dodatno: Podaljševalni nosilec: 2x 6.000 mm