Polpriklopnik z nizko nakladalno ploščadjo

MÜLLER-MITTELTAL 3-achs mit Radmulden, 2 Ladehöhen, Klapprampen

Stanje: novo, največja dovoljena obremenitev: 37.390 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Start-up aid for maneuvering purposes switched to the first axle via EBS (no installation required on the truck side) * Rear axle as self-steering axle with electro-pneumatic steering lock * Locking of the self-steering axle from the driver's cab for maneuvering purposes, controlled via EBS (no installation required on the truck side) ----Suspension: * Air suspension with lifting/lowering device and Ride-to-Return valve ----Electrics / Lighting: * Smart Board mounted on the trailer as an information tool with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12/24 V * LED rotating beacon (removable) at the rear * 2 additional LED reversing lights * 7-pin socket at rear for extended length lighting * Side marker lights with indicator signal control Iedsq Euakjpfx Adxjhu * Tyre pressure monitoring system with display option in the truck via EBS signal (no installation required on the truck side) ----General equipment: * Side underrun protection * Landing gears at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the front wall crossmember (without spare wheel) * Mechanically adjustable warning sign packages at front and rear * Swing arm as carrier for connecting cables from truck to semi-trailer ----Low loader deck: * 2nd king pin position * Fifth wheel platform with 45° chamfered front corners and front tool box made of galvanized powder-coated sheet steel B = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm high aluminium side boards (in RAL colour of choice) on the sides of the fifth wheel platform, foldable and removable * Rear wall -150 mm- high plug-in * Rear slope on fifth wheel platform to low bed approx. 700 mm long with tread plate covering and at the end a perforated strip for attaching aluminium loading ramps * Fifth wheel platform with 50 mm clamped wooden planks and low bed platform with 60 mm clamped wooden planks * Tear plate above the axles * 9 x mechanical folding extensions to 3 m overall width, but not in the rear slope (extension planks available with closed storage compartment across the direction of travel under the loading floor) * 3 mounting shafts under the fifth wheel platform for storage of optional aluminium loading ramps or wooden planks for wheel well coverings ----Load securing (LaSi package): Fifth wheel platform: * Perforated outer frame angled at 45° with hole pattern for lashing points (2 t lashing capacity per point at a minimum spacing of 480 mm) * 3 x 13.4 t lashing rings each side recessed in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal beams after the drop, 1 x above the centre axle next to the longitudinal beam) Low loader platform: * 3 x 13.4 t lashing rings each side on the outer frame (1 x beginning of the drop on the fifth wheel platform, 1 x beginning of the ramp slope, 1 x end of the ramp slope) * 2 x 10 t lashing rings each side (1 x between front wheel well and 1st axle, 1 x between 2nd and 3rd axle) * 3 x 5 t lashing rings each side bolted to the outer frame of the wheel wells (2 on the front wheel well, 1 on the rear wheel well) ----Excavator arm recess: * Extended excavator arm recess from end of last fixed axle through to steering axle up to rear crossmember, continuous with

Stanje: novo, največja dovoljena obremenitev: 36.900 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 ton BPW axles * Start assist for shunting purposes on the first axle, activated via EBS (without truck-side installation) * Last axle is a trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle for maneuvering purposes from the driver’s cab via EBS (without truck-side installation) ----Suspension: * Air suspension with lift and lowering function as well as RtR valve ----Electrics / Lighting: * Smart-Board infotool mounted on trailer with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear * 2 additional LED reversing lights * 7-pin socket at rear for overlength lighting * Side marker lamps with indicator function * Tire pressure monitoring with display in the truck via EBS signal (without truck-side installation) Isdpoykx Nkefx Adxohu ----General Attachments: * Side underrun protection * Support legs at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the front wall crossmember (without spare wheel) * Mechanically adjustable warning sign packages front and rear * Swing arm as a carrier for connecting lines from truck to semi-trailer ----Low Loader Platform: * 2nd king pin position * Gooseneck platform with 45° chamfered front corners and front-mounted toolbox made of galvanized, powder-coated sheet steel B = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm aluminum side boards (in desired RAL color) foldable and removable along the gooseneck platform * Rear wall, insertable, height 150 mm * Rear incline on the gooseneck platform to the low-bed approx. 700 mm long with checker plate covering and at the end a perforated strip for attaching aluminum approach ramps * Gooseneck platform with 50 mm clamped wooden planks, low-bed platform with 60 mm clamped wooden planks * Tread plate over axles * 9 mechanical extension panels to a total width of 3 m, not included in the rear incline (extension planks available with closed transverse stowage compartment under load floor) * Preparation for 3 storage recesses under the gooseneck platform for optional storage of aluminum approach ramps or planks for covering wheel recesses * Preparation for container locks on the swan neck ----Load Securing (LaSi Package): Gooseneck platform: * Perforated outer frame, 45° angled, with hole pattern for lashing devices (2 t lashing capacity per point with a minimum spacing of 480 mm) * 3 x 13.4 t lashing rings recessed into the floor per side (1 x on gooseneck platform, 1 x on longitudinal frame after the cranking, 1 x above middle axle next to longitudinal frame) Low-bed platform: * 3 x 13.4 t lashing rings per side at the outer frame (1 x start of gooseneck cranking, 1 x start of approach ramp, 1 x end of approach ramp) * 2 x 10 t lashing rings per side (1 x between front wheel recess and 1st axle, 1 x between 2nd and 3rd axle) * 3 x 5 t lashing rings per side screwed to outer frames of the wheel recesses (2 at front wheel recess, 1 at rear wheel recess) ----Excavator Arm Rest: * Extended excavator arm rest from end of last rigid axle over the steering axle to the end cross member, continuous with internal reinforcing profile approx. W = 770 mm x T rear

Stanje: novo, največja dovoljena obremenitev: 37.390 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Traction aid for shunting purposes engaged on the first axle via EBS (without truck-side installation) * Last axle as trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle from the driver's cab for shunting via EBS (without truck-side installation) ----Suspension: * Air suspension with lifting and lowering function as well as RtR valve ----Electrics / Lighting: * Smart Board mounted on trailer as info tool with pressure sensors for total axle load display * 15-pin electrical connector * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * 2 extra LED reversing lights * 7-pin socket at the rear for additional length lighting * Side marker lights with indicator activation * Tire pressure monitoring system with display option in the truck via EBS signal (without truck-side installation) ----General attachments: * Side underrun protection * Landing gears at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the headboard crossmember (without spare wheel) * Mechanically adjustable warning sign packages at the front and rear * Swivel arm as carrier for connection cables from truck to semi-trailer ----Lowbed platform: * Second kingpin position * Fifth wheel platform with 45° bevelled front corners and front toolbox made of galvanised, powder-coated steel sheet, W = 2,480 mm x H = 500 mm x L = 665 mm with folding lid * Side aluminium drop sides, 400 mm high (in RAL custom colour), foldable and removable * Rear wall -150 mm- high plug-in * Rear slope on the saddle platform to the lowbed approx. 700 mm long with chequer plate covering and a perforated strip at the end for attaching aluminium loading ramps * Fifth wheel platform with 50 mm clamped wooden planks and lowbed platform with 60 mm clamped wooden planks * Tread plate over the axles * 9 x mechanical folding wideners to 3 m overall width, not in rear slope (widening planks available with sealed crosswise storage compartment under the loading area) * 3 mounting shafts under the saddle platform for the storage of either aluminium loading ramps or wooden planks for wheel well covering ----Load securing (LaSi-package): Fifth wheel platform: * Perforated outer frame, 45° angled, with hole pattern for lashings (2 t lashing capacity per tie-down point at a minimum spacing of 480 mm) * 3 x 13.4 t recessed lashing rings per side in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal members after the cranking, 1 x above the central axle next to the longitudinal member) Lowbed platform: * 3 x 13.4 t lashing rings per side on the outer frame (1 x at the start of the cranked platform, 1 x at the start of the access slope, 1 x at the end of the access slope) Ijdpfstpta Dex Adxshu * 2 x 10 t lashing rings per side (1 x between the front wheel well and 1st axle, 1 x between the 2nd and 3rd axle) * 3 x 5 t lashing rings per side bolted to the outer frames of the wheel wells (2 at the front wheel well, 1 at the rear wheel well) ----Excavator arm rest: * Extended excavator arm rest from end of last rigid axle over steering axle to end crossmember, continuous with internal reinforcing profile approx. W = 770 mm x D rear = 270 mm / D front = 170 mm * 2 x 6.4 t lashing rings per side in the exca