Prikolica delovna ploščad nakup rabljenega (72)

Stanje: novo, lastna masa: 4.400 kg, največja dovoljena obremenitev: 19.600 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.600 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17,5, medosna razdalja: 8.795 mm, Oprema: ABS, | Krone AD Jumbo plato prikolica 3-osna Nova | Multilock zunanji okvir po celotni dolžini | Zračno vzmetenje spredaj in zadaj (dviganje/spuščanje) | Vrtljivo podvozje z krožno kroglo, nizko vzdrževalni vrtljivi venec | Vlečna ušesa 40 mm | BPW osi z bobnastimi zavorami | Nosilec za rezervno kolo | Dimenzije (D x Š x V): 8,60 x 2,48 x 0,93 m | Jeklena čelna stena 1,60 m | Medosna razdalja: 8.795 mm | Pnevmatike 12x spredaj/zadaj: 235/75 R 17,5 | Pridržujemo si pravico do napak, vnosov in predhodne prodaje. Hjdpfsyzm Ecjx Adysff

Stanje: rabljeno, največja dovoljena obremenitev: 600 kg, skupna masa: 750 kg, konfiguracija osi: 1 os, prva registracija: 04/2025, dolžina tovornega prostora: 2.500 mm, širina tovornega prostora: 1.260 mm, višina nakladalnega prostora: 300 mm, skupna širina: 1.710 mm, skupna višina: 790 mm, Zabojni priklopnik je izdelan iz stabilne aluminijaste konstrukcije in obrabno odpornega lesenega poda. Pridržujemo si pravico do napak in vmesne prodaje. Hfodpfxjy A A Sno Adyof

Stanje: rabljeno, največja dovoljena obremenitev: 2.775 kg, skupna masa: 3.500 kg, konfiguracija osi: 2 osi, prva registracija: 02/2026, dolžina tovornega prostora: 3.530 mm, širina tovornega prostora: 1.650 mm, skupna širina: 2.435 mm, skupna višina: 2.130 mm, A15 GW26NG00315 Prevoznik gradbenih strojev proizvajalca STEMA, tip BMAT, skupna masa: 3.500 kg, nizkopodnožni priklopnik, vztrajnostna zavora, 100 km/h, z aluminijastimi rampami, 3,53 m x 1,65 m ...in še veliko več. Pridržujemo si pravico do napak in vmesne prodaje. Višina nakladanja 500 mm Hfjdpsym Iftjfx Adysf

Stanje: rabljeno, največja dovoljena obremenitev: 2.775 kg, skupna masa: 3.500 kg, konfiguracija osi: 2 osi, prva registracija: 02/2026, dolžina tovornega prostora: 3.530 mm, širina tovornega prostora: 1.650 mm, skupna širina: 2.435 mm, skupna višina: 2.130 mm, A15 GW26MG00273 Hfodpfx Aoym Ihzsdysf Prevoznik gradbenih strojev, proizvajalec A, tip BMAT, skupna teža: 3.500 kg, nizkopodni priklopnik, s inercijsko zavoro, 100 km/h, z aluminijastimi rampami, 3,53 m x 1,65 m ...in še veliko več. Pridržujemo si pravico do napak in predhodne prodaje.

Stanje: rabljeno, največja dovoljena obremenitev: 2.186 kg, skupna masa: 2.700 kg, konfiguracija osi: 2 osi, prva registracija: 02/2026, dolžina tovornega prostora: 3.005 mm, širina tovornega prostora: 1.400 mm, višina nakladalnega prostora: 200 mm, skupna širina: 2.035 mm, skupna višina: 2.130 mm, A45 GW26G000189, Transporter gradbenih strojev, proizvajalec STEMA, tip BMAT .2, Skupna masa: 2.700 kg, z jeklenimi nakladalnimi rampami, inercialna zavora, 100 km/h, 3,01 m x 1,40 m Vgrajeni blažilci za 100 km/h * Tandem nizek priklopnik, po izbiri z STEMA V-ojem ali centralno cevjo * Zvarjeno in v potopni kopeli vroče pocinkano podvozje iz masivne jeklene pločevine * Sprednja in stranske stene iz 3 mm debele varjene črne pločevine * 20 cm visoke zvarjene stranske stene Hedpfeyqdqmsx Adyeff * Celotno pohodno dno iz vezane plošče s protizdrsnim premazom (debeline 18 mm), po izbiri tudi dodatno aluminijasto rebrasto dno (debelina 3 mm) * Pohodna jeklena blatnika za enostavno vstopanje in izstopanje * 2 vzdolžna nosilca za optimalno porazdelitev tovora ... in še veliko več. Napake in vmesna prodaja pridržane.

Stanje: rabljeno, največja dovoljena obremenitev: 2.649 kg, skupna masa: 3.500 kg, konfiguracija osi: 2 osi, prva registracija: 02/2026, dolžina tovornega prostora: 4.005 mm, širina tovornega prostora: 1.800 mm, skupna širina: 2.435 mm, skupna višina: 2.130 mm, A14 GW26GA00002 Prevoznik gradbenih strojev, proizvajalec STEMA, tip BMAT .2, skupna masa: 3.500 kg, nizkopodni priklopnik, z vztrajnostno zavoro, 100 km/h, s kovinskimi rampami, nagibni, 4 m x 1,80 m ...in še veliko več. Pridržujemo si pravico do napak in vmesne prodaje. Hjdpjym Ifasfx Adyeff

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: W09K35135G1KB6013, Leto izdelave: 2016, obratovalne ure: 1.823 h, TÜV veljaven do 08/2026, po želji tudi nov. Vključena ustrezna oprema: klešče, posoda za ruševine, kletka za obešanje. Hfsdpfxsyt Hhme Adyof

Stanje: novo, največja dovoljena obremenitev: 15.825 kg, skupna masa: 20.500 kg, konfiguracija osi: 2 osi, širina tovornega prostora: 2.480 mm, skupna širina: 2.550 mm, Oprema: ABS, You can find our complete range of vehicles, including units available for immediate or short-term delivery, on our website. Excerpt from equipment specification. Full equipment details available upon request. Chassis: * Steel welded construction made of welded longitudinal beams and punched Z-cross members, close cross member spacing for high floor load capacity * Ramp storage between the longitudinal beams behind the axle assembly under the load floor, two insertion slots for one ramp each, with locking plate in the rear header frame Underride guard: * According to EC regulations Front landing gear: * Single-sided operated landing legs Rear support: * Two adjustable drop legs Axles: * 2 x 10 t air suspension axle assemblies, manufacturer SAF, drum brakes approx. 300 x 200 mm, hub-centered wheel fixing for twin tyres, ABS, total air suspension travel approx. 200 mm (raise approx. 140 mm, lower approx. 60 mm), operated by hand lever with ratchet function Tyres: * 8 units, 235/75R 17.5 – make as per our choice, on steel rims 6.75 x 17.5, fitted with offset Splash protection: * PVC spray guards in front of and behind axles, EC compliant Load securing: * On the outer frame approx. every 150 mm a hole for lashing straps, tensile strength approx. 2.5 t (lashings can be hooked in with side walls closed, bevelled outer frame) * 6 pairs of foldable lashing rings, evenly distributed, tensile strength approx. 8 t * Stake pockets for removable stanchions 80/50: 3 pairs of stake pockets on the outer frame, evenly distributed Brake system: * Compressed air brake system according to EC regulations with EBS * Two spiral hoses as connection to the towing vehicle with red/yellow coupling heads * Spring-loaded parking brake acting on one axle Floor: * Approx. 28 mm Z-hardwood floor recessed into the outer frame Front wall: * Made from 25 mm removable front board Lighting system: * Lighting in accordance with EC regulations, 24 volt, multi-chamber tail lights, number plate lights, side marker lights and lane control lights at the rear, connection plate on the left of the drawbar including connection cable with 15-pin and two 7-pin plugs Accessories: * 2 wheel chocks with holders * Removable warning beacon at the rear * Additional 40 mm coupling device supplied (max. GVW 13,500 kg) * Rear extension approx. 800 mm including underride guard, extendable loading platform with load capacity approx. 2 t, locking positions every approx. 200 mm * Mechanically adjustable rigid drawbar, 6 x approx. 100 mm increments, with bolt-on towing eye approx. 50 mm as per DIN 74053 * 4 rows of crosswise stake pockets evenly distributed across the loading platform Hedpfxsy Auhbo Adyeff * 12 removable stanchions made of galvanized pipe, approx. 80/50/4 mm, approx. 1,000 mm long * Container locks for one 20’ container, container locks extendable to approx. 2,820 mm, according to ISO 1496, EN 284 or EN 452 * 1 pair aluminum ramps, load capacity per pair approx. 9,000 kg * 4 stainless steel toolboxes between or behind the axles * 6 pieces of 25 mm side walls and a rear wall made of anodized aluminum hollow profiles, approx. 600 mm high, foldable and removable, removable Kinnegrip stanchions (internal width approx. 2,480 mm), includes side wall holder at front wall Paintwork: * Chassis shot-blasted, cleaned, and hot-dip galvanized to latest standards * Structure parts cleaned, primed and hot-dip galvanized * Chassis: Hot-dip galvanized & RAL 3002 carmine red * Side walls: RAL 3002 carmine

Stanje: novo, največja dovoljena obremenitev: 16.180 kg, skupna masa: 20.500 kg, konfiguracija osi: 2 osi, skupna širina: 2.480 mm, Oprema: ABS, You can find our complete range of vehicles with immediately and soon-available stock on our website. Excerpt from the features list. Full specification available on request. Chassis: * Welded steel construction with welded longitudinal beams and perforated Z-cross members, closely spaced cross members for high floor load capacity * Ramp compartment: between the longitudinal beams, behind the axle assembly underneath the loading floor, two insertion pockets for one each loading ramp, with locking plate in the rear headframe Underrun Protection: * According to EU regulations Landing Gear: * Front: landing legs with one-sided operation * Rear: two adjustable drop supports Axles: * 2 x 10 t air suspension axle assembly, manufacturer SAF, drum brakes approx. 300 x 200 mm, center-aligned for twin tires, ABS, total air suspension stroke approx. 200 mm (lifting approx. 140 mm, lowering approx. 60 mm), operated via hand lever with detent function Tires: * 8-fold, 235/75 R17.5 – our choice of brand. Mounted on 6.75x17.5 wheels with offset Spray Protection: * PVC, in front of and behind the axles, according to EU regulations Load Securing: * On outer frame, approx. every 150 mm, a hole for lashing straps, tensile strength approx. 2.5 t * 6 pairs of foldable lashing rings evenly distributed, tensile strength approx. 8 t * Stake pockets for slip-in stakes 80/50: 3 pairs of stake pockets in the outer frame, evenly distributed Brake System: * Compressed air brake system as per EU standards with EBS * Two spirals as connection to the towing vehicle with red/yellow coupling heads Hjdjy Auf Tepfx Adysff * Spring-loaded parking brake acting on one axle Floor: * Approx. 28 mm Z-hardwood floor sunk into the outer frame Lighting System: * Lighting system as per EU standards, 24 volts, multi-chamber tail lights, license plate lights, side marker and track marker lights at the rear, connection plate on the left drawbar, incl. interconnection cable with 15-pin and 2 x 7-pin connectors Accessories: * 2 wheel chocks with holder * Removable flashing beacon at the rear * 40 mm towing device supplied (max. gross weight 13,500 kg) * Rear extension approx. 800 mm including underrun protection, extendable loading platform with load capacity approx. 2 t, locking positions every 200 mm * Mechanically length-adjustable rigid drawbar, 6 x approx. 100 mm, with bolted towing eye approx. 50 mm as per DIN 74053 * 4 rows of crosswise stake pockets across the load floor, evenly distributed * 12 galvanized steel stakes, approx. 80/50/4 mm, approx. 1,000 mm long * Container locks for 1 x 20’ container * Container locks for 1 x 20’ container, extendable to approx. 2,820 mm, according to ISO 1496, EN 284, or EN 452 * 1 pair of aluminum loading ramps, load capacity per pair approx. 9,000 kg * 4 stainless steel toolboxes between or behind the axles Paintwork: * Chassis shot-blasted, cleaned, and high-quality hot-dip galvanized to the latest technical standards * Superstructure parts cleaned, primed, and hot-dip galvanized * Chassis: hot-dip galvanized + RAL 9011 graphite black * Outer frame: hot-dip galvanized + RAL 9010 pure white * Hubs: KTL black * Underrun protection: RAL 9010 pure white * Rims: RAL 9006 silver * Add-on parts: galvanized / KTL black

Stanje: novo, največja dovoljena obremenitev: 16.750 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 21.0: * Wabco EBS-E (electronic braking system) * RDÜ tyre pressure monitoring system * Emergency release mechanism for spring brake cylinders * Drum brakes * 2 x 11 t Gigant axles * Air suspension with lifting and lowering function * Mounting provisions at the front bulkhead and rear slope for subsequent fitting of container locks for transporting 20" containers * Drawbar with 50 mm flange towing eye and height-adjustable drawbar * Jost landing gear at the front * Rear external folding supports * Plastic toolbox approx. 750 x 350 x 300 mm, right-hand side * Side underrun protection * Plastic quarter mudguards * 15-pin power socket * LED lights * 21 t GVW version with reinforced frame and reinforced axles * Reinforcement package on the chassis for drilling rig transport * 50 mm softwood floor, clamped design * Provisions at the front bulkhead for retrofitting container locks * Bolted front bulkhead made from smooth sheet metal * Split, foldable trapezoidal-profile steel sidewalls with centre folding stake * Steel rear wall, insertable between ramps – storage bracket inside front bulkhead when not in use * Screw-mounted rear stakes * Perforated outer frame, approx. 45° bent, with 2 t lashing capacity every 480 mm * Option for fitting 3 t folding lashing rings every 600 mm * Profifix lashing rail centrally on longitudinal axis for lashing up to LC 3000 daN * 1 x 10 t lashing ring each at front and rear corners * Lashing package: 2 x 8 t retractable lashing rings per side recessed into the outer frame; various holes in the bulkhead and rear crossmember for lashing up to 1.2 t * One-piece mechanical grating ramps with spring mechanism for single-person operation approx. 3,000 x 620 mm (can be collapsed to 20 mm) * Rear entry angle approx. 860 mm on chassis * Drawbar, front wall, tailgate, folding supports and ramps hot-dip galvanised * Axles, springs, air tanks, and landing gear finished in black paint * Load height unladen approx. 940 mm * Loaded approx. 910 mm * Wheelbase: 1,810 mm * Tyres: 235/75R17.5 * Side wall painting colour freely selectable up to approx. 2 weeks before production date, except metallic and special colours Hfsdsl Tihxjpfx Adysf * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from CW 29 / 2026

Stanje: rabljeno, največja dovoljena obremenitev: 15.250 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2007, ? Balastna platforma ? 50 mm vlečna kljuka ? 5 x pritrdilna ušesa ? Bobnaste zavore ? Listnato vzmetenje ? Podporne noge ? BPW osi Hedow Sqi Eepfx Adysff Vsi podatki brez garancije / vmesna prodaja pridržana.

Stanje: rabljeno, največja dovoljena obremenitev: 13.860 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2022, dolžina tovornega prostora: 6.770 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 600 mm, prostornina tovornega prostora: 10 m³, Oprema: ABS, ? pocinkano podvozje ? nizko sklopljen ? vlečno oko 50 mm ? zaklep za kontejner ? po 12 pritrdilnih obročev na vsaki strani ? vzvratna kamera ? bobnaste zavore ? duomatski priključek ? ABS ? zračno vzmetenje ? orodjarna ? EBS ? podporne noge Hfodpfx Adoxb Ig Ssyof ? dvojna kolesa ? BPW osi Vse informacije brez garancije / Vmesna prodaja pridržana.

Stanje: rabljeno, največja dovoljena obremenitev: 15.250 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 12/2008, ? Platform for ballast weights ? 50 mm towing eye ? 4 x lashing eyes Hsdpewfk R Defx Adyeff ? Drum brake ? Leaf suspension ? Support legs ? BPW axles All information without guarantee / subject to prior sale.

Stanje: rabljeno, Ima TÜV in veljaven UVV. Izstavi se račun z vključenim DDV-jem. DDV je ločeno izkazan. Preda se le odjavljen. Hedpfx Adsy A Ratjysff

Stanje: rabljeno, največja dovoljena obremenitev: 17.520 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, prva registracija: 01/2013, dolžina tovornega prostora: 9.100 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 600 mm, skupna širina: 2.550 mm, skupna višina: 1.720 mm, Oprema: ABS, 3-Axle Zikun ZK-AD3-PRXX Flatbed Container Trailer VIN: Z04127 Chassis / Attachments: * Air suspension with raise/lower function * Lifting axle * 3 x SAF axles with disc brakes * Tyres: 265/70 R19.5 * Remaining tread: Front ~60%, Middle ~80%, Rear ~80% * Twin tyres * 2 x PVC storage boxes * Storage basket on left side * Ride height approx. 1.10 m Superstructure: * Zikun flatbed * Drop sides 600 mm * Kinnegripp folding stakes * Steel chequered plate floor * 5 x container locks per side * 8 x pockets for container locks per side * 14 x heavy-duty lashing rings per side * 6 x heavy-duty lashing rings recessed in floor per side * Edscha sliding roof * Lashing rings * Dimensions: 9,100 mm x 2,480 mm x 600 mm * 22 pallet spaces Weights: * Gross weight: 24,000 kg * Unladen weight: 6,480 kg * Payload: 17,520 kg Other: * 1 previous owner * New roadworthiness inspection (HU) available * Very good condition New general inspections / safety inspections or weight downgrades/upgrades possible on request. We are happy to assist with obtaining export/transfer license plates, and can also organise transport of your purchased vehicles within Germany. Contact us! ---- We speak: German, English, and Russian! ---- No liability for printing & typographical errors. Subject to change, prior sale, and error! ---- Who are we? Leible Nutzfahrzeuge is a family business based in Kehl am Rhein. With many years of experience in the preparation and sales of commercial vehicles, we are a reliable partner for customers worldwide. Leible Nutzfahrzeuge specialises in the sale of new and used commercial vehicles. On a site of 11,000 m², a large selection of vehicles is available. Our company philosophy is characterised by fairness and integrity. Customer satisfaction is our top priority; we offer an excellent all-round service package and provide each customer with a competent contact person to support them during the purchase or sale of vehicles. See for yourself! Our services for you: Loading of vehicles We are happy to assist with loading your purchased vehicles. Organising special transports We can help organise special transports for you. Temporary/export licence plates We are happy to assist with obtaining export/temporary licence plates. Customs formalities Hsdpfx Aoyadu Redyoff We are happy to assist with customs procedures.

Stanje: rabljeno, največja dovoljena obremenitev: 1.007 kg, skupna masa: 1.500 kg, konfiguracija osi: 1 os, prva registracija: 03/2026, dolžina tovornega prostora: 3.070 mm, širina tovornega prostora: 1.870 mm, višina nakladalnega prostora: 100 mm, skupna širina: 1.960 mm, skupna višina: 925 mm, A66 GW26NG000373 Homologacija za 100 km/h Hsdpfxsyq U Enj Adyeff Platformni priklopnik Oporno kolo Nakladalne rampe Pridržujemo si pravico do napak in predhodne prodaje

Stanje: novo, največja dovoljena obremenitev: 31.900 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release for spring-actuated cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lift/lowering function and RtR valve ----Drawbar: * Straight drawbar with 50 mm towing eye and continuously adjustable height ----Electrics / Lighting: * Tire pressure monitoring system with display option in truck dashboard via EBS signal – no installation required on truck * SmartBoard as infotool with pressure sensors for axle load display per axle group * 15-pin power connector * LED taillights * Removable LED beacon at rear Hfsdpfeylfvgox Adyof ----General attachments: * Warning plates front & rear * 2 x toolboxes made of galvanized, powder-coated sheet steel approx. 650 x 300 x 600 mm, right side * Closed single plastic mudguards at front * Straight steel spray suppression panels at rear, each with spray suppression * Side underrun protection ----Low-bed platform: * Turntable/platform extension by 520 mm with 45° corners and 3 recessed storage compartments incl. lids and lockable * Flooring on turntable platform made of 50 mm softwood; on low-bed platform made of 60 mm softwood * 20 mm rubber covering instead of timber in drive lane area with a well length of 6,780 mm including sloped ramp * Rubber coating on the ramp left and right, approx. 860 mm length * 4 stake pockets per side (stakes not included) with simultaneous 2 t lashing point capability ----Chassis: * Chassis made of high-strength fine-grain steel ----Load securing (Lasi package): Turntable/platform: * 2 pairs of 13.4 t lashing eyes in outer frame of turntable/platform Low-bed: * 4 pairs of 10 t lashing rings per side on the outer frame, foldable and loadable in all directions * 2 pairs of 13.4 t swiveling lashing rings at rear on each side ----Ramps: * Rubber covering on foldable access ramps * Hydraulic folding ramps with hydraulic tip extension approx. 4,650 x 720 mm * Hydraulically lateral ramp shift & load-holding valves ----Rear support: * Hydraulic rear support ----Widening: * 8 pairs of galvanized folding outriggers for 3 m overall width (not on rear bevel) * Widening boards stowed on left side compartment ----Excavator boom trough: * Excavator boom trough above rear axle to end of slope approx. L=2,100 mm x W=740 x D=190 mm * 2 pairs of 6.4 t lashing rings at sides in excavator trough ----Hydraulics: * Hydraulic flow divider in trailer (for truck hydraulic pump outlet above 40 up to max. 120 ltr./min.) ----Loading dimensions: * Rear loading platform: approx. 6,780 x 2,520 mm (incl. 860 mm ramp) * Platform above turntable: approx. 2,990 x 2,520 mm ----Loading height: * Loaded approx. 890 mm, +/- 20 mm ----Paintwork: * Reflective contour tape at sides and rear * Chassis, turntable, access ramps and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks and turntable painted in black tone ----Info: * New vehicle with manufacturer warranty * Errors and prior sale reserved * Sample images may show special equipment ----Lead time: * Vehicle available from approx. week 23/2026

Stanje: rabljeno, največja dovoljena obremenitev: 949 kg, skupna masa: 1.300 kg, konfiguracija osi: 1 os, prva registracija: 02/2026, dolžina tovornega prostora: 4.010 mm, širina tovornega prostora: 188 mm, višina nakladalnega prostora: 110 mm, skupna širina: 2.450 mm, skupna višina: 860 mm, A13 GW2616429 Multitransporter 4018, Proizv. TEMARED, Tip DMC, . , Skupna teža: 1300 kg, 400x184cm, z inercijsko zavoro, 100 km/h (dodatna oprema), s zložljivo nakladalno rampo (dodatna oprema), nizkopodni, z možnostjo spuščanja Nakladalna višina 400mm Pridržujemo si pravico do napak in vmesne prodaje. Hodpfx Adjym Igdeysff

Stanje: rabljeno, največja dovoljena obremenitev: 31.250 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 07/2014, dolžina tovornega prostora: 9.010 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, Leto izdelave: 2014, Oprema: ABS, 4-axle Schwarzmüller T4 low-loader trailer VIN: EZ346388 Chassis / Attachments: * Leaf suspension * 4 x SAF axles with drum brakes * Tyres: 235/75 R 17.5 * Tyre tread: 1.~60% 2.~60% 3.~60% 4.~50/20% Body: * Overall length: 9.1 m * Extendable lateral widening (up to 3.0 m) * Ride height: 0.90 m Hfedpfsyumbvsx Adyjf * Hydraulic loading ramps with lateral displacement * Various lashing points available Weights: * Gross vehicle weight: 40,000 kg * Unladen weight: 8,750 kg * Payload: 31,250 kg Other information: * German vehicle * 1 previous owner * Next safety inspection: 09/2026 * New general inspection available on request ---- New general inspections / safety checks or weight downgrading/upgrading are possible upon request. We are happy to assist in obtaining export/temporary registration plates. Transport of your purchased vehicles within Germany is also possible. Contact us! ---- We speak the following languages: German, English and Russian! ---- No liability for printing or typographical errors. Subject to change, prior sale and errors! ---- Who are we? Leible Nutzfahrzeuge is a family-run business based in Kehl am Rhein. With many years of experience in the preparation and sale of commercial vehicles, we are a reliable partner for customers worldwide. Our particular strength lies in the sale of new and used commercial vehicles. On an area of 11,000 m², you will find a wide variety of vehicles. Our corporate philosophy is founded on fairness and reliability. Since customer satisfaction is very important to us, we offer our customers an excellent all-round service package, providing them with a competent contact person to assist with the purchase or sale of vehicles. See for yourself! Our services for you: Vehicle loading We are happy to assist with loading your purchased vehicles. Organizing special transports We are happy to help organize special transports for you. Temporary/Export number plates We are happy to help you obtain export or temporary registration plates.

Stanje: novo, največja dovoljena obremenitev: 30.080 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – without truck-side installation * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning panel packages front & rear * SmartBord infotool installed with pressure sensors for total axle load display per axle group * Reflective contour tape on the sides and rear * LED rotating beacon (removable) at the rear * 15-pin power connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front closed single plastic mudguards * Straight rear steel mudflaps, each with spray suppression * Side underrun protection * Superstructure in front of the bogie platform approx. 520 mm with 45° corners and 3 storage compartments including lockable folding lids (folding lids opening to the rear) * Chassis made from high-strength fine-grained steel * Floor over the bogie platform made of 50 mm softwood, and 60 mm softwood in the low loader platform * Outer planks of the drive-on ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing eyes 6.4 t front left and right on the main frame of the bogie platform, 1 pair each of 13.4 t lashing rings at the front and rear outer frame, 1 pair each of 10 t lashing rings, swiveling and lowerable, loadable in all directions and recessed in the outer frame, 5 t lashing rings bolted to the outer frame of the wheel recesses (2 at the front recess, 1 at the rear), 2 pairs of 6.4 t lashing rings on the excavator stick holder * 11 pairs of folding outriggers for a total width of 3 meters (not at the rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for the widening boards made of sheet steel, mounted transversely to the loading area in front of the first rear axle * Excavator stick holder above the rear axle up to the end of the approach slope approx. 2,300 x 740 x 190 mm * Two wheel recesses per side approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with retractable cover (storage for covers at the front on the bogie platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm * Hydraulic lateral ramp shift * Loading area over the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loading height loaded approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, bogie, folding outriggers, rear drop-down supports, and drive-on ramps galvanised Hodpfxjxmpydo Adyeff * Axles, air tanks, and drawbar painted in black * Tires: 235/75R17.5 * Vehicle is galvanised * New vehicle with manufacturer’s warranty * Errors and prior sale reserved * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 38.620 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, T5 Profile 50.0: ----Braking System: * Wabco EBS (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (when lifted, ride height +30 mm) * Last axle is self-steering (lockable from the cab for maneuvering purposes without any installation on the truck side, and additionally via a switch on the trailer). The lock must be disengaged before driving on public roads. * Forced lifting and lowering of the lift axle for maneuvering (truck-side installation required), with speed-dependent control via the EBS electronics ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: Drawbar 1,500 mm long with 50 mm draw eye and manual height adjustment ----Electrics / Lighting: * Smartboard as an info tool with pressure sensors for axle load indication per axle group * Tire pressure monitoring with display in the truck via EBS signal (without truck-side installation) * LED lighting system 12/24 V * LED rotating beacon (removable), rear ----General Fittings: * Mechanical warning sign set for 3 m total width * Toolbox made of galvanized steel plate approx. 650 x 300 x 600 mm, mounted left side * Plastic fenders front axle and galvanized steel mudguards rear axle ----Low Loader Platform: * Front section of turntable platform with 45° corners and 3 stowage compartments with lockable folding lids (folding towards the rear) * Shortening of the low-bed platform by 500 mm to 6,280 mm including extended recess by 500 mm at the front * Rubber covering on the folding frame, approach ramp, and running surface of the low-loader platform * Bamboo wood between the longitudinal beams, in front of the excavator stick rest area ----Load Securing (LaSi Package): * 2 x 6.4 t lashing eyes in the front corners * 2 x 13.4 t UVV lashing points on each side in the front and rear corners * 5 x 10 t UVV lashing rings on each side (swivelable and lowerable, loadable in all directions) * 4 stake pockets per side with simultaneous 2 t lashing option * 1 x 16 t UVV lashing ring on the rear crossmember ----Width Extension: Hjdpfoxptn Dex Adyoff * Extendable and foldable width supports for 3 m total width (plank holder under the chassis, right side) ----Excavator Stick Rest: * Continuous excavator stick rest with reinforcement profile from last axle to end beam approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on the sides of the excavator stick rest ----Ramps: * Hydraulic folding ramp with dual-circuit hydraulics and folding tip approx. 4,650 x 720 mm, including load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (for hydraulic pump outputs on the truck over 40 l/min up to max. 140 l/min) ----Loading Height: * Loaded: 890 mm +/- 20 mm adjustable via air suspension ----Loading Area Dimensions: * Platform above turntable: 2,600 + 390 x 2,520 mm * Low-bed loading platform: 6,280 + 500 x 2,520 mm, incl. 860 mm approach ramp ----Paintwork: * Chassis, turntable, drawbar, width extension consoles, ramps hot-dip galvanized * Drawbar yoke, axles, hydraulic axle supports and air tanks painted in black ----Information: * New vehicle with manufacturer warranty * Subject to prior sale and errors ----Delivery Time: Available immediately*

Stanje: kot nova (razstavni stroj), številka stroja/vozila: AHW MT3080, skupna masa: 3.000 kg, dolžina tovornega prostora: 3.080 mm, širina tovornega prostora: 1.520 mm, TRAILERWIRTZ, the online pick-up market for your new trailer, offers strong brand-name models ready to take away! - Over 850 new trailers in stock - Over 100 used trailers always available - Over 150 vehicle transporters – popular models with extensive accessories in stock Non-binding example: exhibition trailer ready for collection Hfjdpfjyrbnfsx Adyef Brenderup machine transporter MT 3080 GD 308x152cm 3000kg, low loader with tandem axle, V-drawbar, loading ramp as rear gate with supporting leg 13-pin plastic connector, tires: 14 inches Jockey wheel, 6 internal lashing rings (400 daN) Excavator bucket rest Non-slip mudguard coating and step board Hot-dip galvanized, high-quality durable screen-printed floor Sturdy metal chocks, position lighting Recessed lights Spare wheel incl. holder under bucket rest The largest selection of transporters available immediately Sales by telephone order during business hours or 24/7 through our trailer shop Images and description in this advertisement are protected by copyright – logos are trademark protected 03/26 39033

Stanje: rabljeno, skupna masa: 2.100 kg, konfiguracija osi: 2 osi, prva registracija: 10/2021, skupna širina: 2.150 mm, skupna višina: 2.330 mm, Oprema: žerjav, Very well-maintained trailer-mounted work platform with a working height of 16 m, basket load capacity of 200 kg, lateral outreach of 9.45 m, power supply to the basket, and including generator. UVV inspection was carried out by Paus in March 2026. GT 16 AG Work Platform - Working height: 16 m - Telescopic design - Lateral outreach: 9.45 m - Basket load capacity: 200 kg - 220 V power feed to basket - Including generator - Fully hydraulic outriggers - Support width: 4.08 m - Support length: 4.29 m - Continuous 360° rotation - Total length: 6.31 m - Transport width: 2.15 m - Transport height: 2.33 m - Weight: 2,100 kg Financing available through our partner banks; we are happy to assist you. Hsdpfx Adjyw Ergoyjff We expressly reserve the right to prior sale, as we also list this item on other platforms. Details of included accessories are provided without guarantee. Subject to changes, interim sale, or errors. We strongly offer and recommend viewing and inspection to ensure there are no misconceptions regarding condition or suitability on the buyer's part. Viewing and inspections are possible at any time by appointment and are expressly encouraged.

Stanje: novo, največja dovoljena obremenitev: 16.500 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal ETÜ-TAR 21 Tandem – Low-Loader | Drive-over Platform Trailer Ref. for inquiries: 11630 Vehicle immediately available ex-stock Alsdorf NEW VEHICLE including COC (Certificate of Conformity) * Gross weight: 21 t, Payload: 16.5 t, galvanized chassis * Platform design with 400 mm high front wall, ramp safety by ramp holding frame and slanted bracing * Design: GW 21 t, reinforced frame and axle, axle spacing 1,810 mm * Deck height approx. 910 mm loaded / approx. 940 mm unloaded * 7 m loading area with 400 mm high front wall * Extended ramps: 3 m ramps, hot-dip galvanized, one-piece with galvanized grating * Ramp lifters with vertically mounted, adjustable springs for easy one-person operation * La-Si package: * 4 UVV safety lashing brackets (LC 8,000 daN), mounted to the existing hole pattern in the 45° outer frame, positioned about 1 m from the front and rear crossmembers * 10 retractable UVV lashing brackets (LC 3,000 daN) in the existing hole grid in the outer frame * 2 UVV lashing rings each at the front and rear, recessed in the crossmember (LC 10,000 daN) * Additional lashing points with 50 mm Ø drillings (LC 1,200 daN) in the front and rear crossmembers * Pre-fitted for retrofitting container locks (container locks available at extra charge) * Softwood floor, 50 mm thick * Air suspension, Gigant axles incl. EBS 2S/2M, raising and lowering * 235/75R 17.5 (8 units) twin tires with tire pressure monitoring sensors * Plastic toolbox in front of the front wall, right side in direction of travel * LED lighting system * 7-pin socket at the rear, prewired for oversize lighting with tail light (58R) and ground connection * 2 rear LED reverse lights * Side marker lights, flashing * Warning sign for oversize load * 1 removable LED rotating beacon incl. bracket and installation * Folding supports at the rear, support leg at the front with gear winch ---- Lease-purchase example from our partner MMV Leasing: €655/month net for 60 months, no down payment, and "0" Euro residual value Other terms with/without down payment/residual value available! We are official Müller-Mitteltal dealer ---- Our opening hours: * Monday – Thursday: 08:00 – 17:00 * Friday: 08:00 – 15:00 * Outside these hours, appointments possible by arrangement * We speak German, English, Russian, Polish, and French * WhatsApp Hfedpfsyvxg Ujx Adyef

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profile 30.0: * EBS braking system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical rear axle equalizer * Side underrun protection * Swivel supports at the rear on the chassis frame * Mechanically adjustable warning sign kits at the front and rear * Front: closed plastic mudguards, rear: straight galvanized steel mud flaps, each with splash guards * Contour marking tape, reflective, on sides and rear * Foldable (hot-dip galvanized) tool box cover on the turntable platform * Multi-voltage system Hfedpfxox Ipa Ne Adyef * LED tail lights * Rotating beacon (removable) at the rear * Drawbar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin power connector * Four stake pockets each side (no stakes included), also suitable for lashing * Load securing package consisting of: 2 lashing points (6.4 t) at the front left & right on the main frame of the turntable platform, 5 pairs of UVV swivel and retractable lashing rings, loadable in all directions and recessed into the outer frame (13.4 t in corners, otherwise 10 t) * 6 pairs of mechanical folding outriggers for total width of 3 m (not in the rear slant) * Widening planks stored in the center of the loading area * Excavator arm support over rear axle up to the rear cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the sides in the excavator arm support) * Mechanical one-piece ramps with spring mechanism (approx. 3,000 x 720 mm) * Mechanically adjustable lateral ramp displacement * Loading area above the turntable: approx. 1,960 x 2,520 mm * Unladen loading height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height approx. 910 mm (including 860 mm approach incline) * Chassis, turntable, drawbar, and ramps hot-dip galvanized * Axles, springs, air tanks, etc. painted black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * -- Gross technical weight of 30,000 kg possible -- * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Subject to prior sale and errors * Immediately available ex Egestorf