Prikolica delovna ploščad nakup rabljenega (65)

Stanje: rabljeno, največja dovoljena obremenitev: 31.000 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, prva registracija: 07/2024, dolžina tovornega prostora: 9.290 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 950 mm, * PT 40.0 Profi ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lifting and lowering system, including RtR valve ----Drawbar: * Drawbar with 50 mm towing eye and height adjustment ----Lighting / Electrics: * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power connector * LED lighting system 12 / 24 V * Removable rear LED beacon * 2 LED reversing lights (activated via reverse gear) ----General equipment: * Manometer - pressure gauge for load weight determination (axles separated into 2 air suspension circuits) * Side underrun protection * Swing-down supports at the rear of the chassis frame * Mechanically adjustable warning sign sets front and rear * VA plastic quarter mudguards with spray protection * HA straight galvanized steel skirts with spray protection * Reflective contour tape on sides and rear * Tool box, galvanized steel sheet, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high ----Low loader platform: * Forepart in front of the turntable platform, approx. 490 mm long with 45° corners * ROBOT-welded anti-slip surface on the steel plate of the turntable platform * Hardwood floor on the running surfaces of the low loader platform Knsdpfjl Tlhrex Ab Sjb ----Load securing (La-Si package comprising): * In front of the front wall support, 1 x 13.4 t UVV lashing point each left & right * 4 lateral holes each in the turntable platform with 2 t lashing capacity each * 1 pair of lashing points (13.4 t) hanging at the rear left & right in front of the rear support * 4 pairs of UVV lashing rings (10 t) on each side, swiveling and lowering, loadable in all directions and recessed in the outer frame * 3 pockets for stanchions per side, with simultaneous 2 t lashing facility ----Widening package: * Hot-dip galvanized mechanical folding outriggers for 3 m overall width (not in the rear taper) * Plank holder for extensions under the chassis on the left, longitudinally ----Excavator arm rest: * Excavator arm rest above HA up to the end support, approx. 2,100 mm long and approx. 190 mm deep * 2 pairs of 6.4 t lashing points each side in the excavator arm rest ----Ramps: * Hydraulic one-piece approach ramps (approx. 3,000 x 720 mm), mechanically adjustable sideways * Outer planks of ramps made from hardwood * Steel structure prepped for 6-section control valve ----Loading height: * Loading edge unladen approx. 950 mm +/- 20 mm ----Tires: * 235/75 R 17.5 tires ----Paintwork: * Chassis, turntable, folding outriggers, mechanical supports, and approach ramps hot-dip galvanized * -- Axles, air tanks, drawbar finished in a shade of black -- ----Information: * Vehicle has a day registration in 07/2024 due to missing tire pressure monitoring system, and has not been loaded/used * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.800 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: ----Brakes: * EBS brake system * Emergency release device for spring-loaded cylinders Knsdpfxerwc R Rs Ab Ssb * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with equalizing device ----Drawbar / Flange Hitch Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm to a total of 2,250 mm ----Electrics / Lighting: * Tire pressure monitoring system with display option in the truck via EBS signal – no installation required on the truck side * 15-pin power connector * LED lighting system 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics ----General Fittings: * Landing gear at the front * External folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, fitted front right outside on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Bed: * 50 mm softwood floor * Provisions in front of the bulkhead for retrofitting container locks * Bolt-on 400 mm bulkhead made of smooth sheet * Removable rear stanchions, bolted * Drop sides with spring assist ----Load securing: * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Option to install 3 t retractable lashing rings every 600 mm * 1 x 6.3 t lashing point in each front and rear corner * Various holes in the headboard and rear crossmember for 1.2 t lashing options * Profifix lashing rail centrally positioned along the longitudinal axis for securing up to LC 3000 daN ----Ramps: * One-piece hydraulic mesh drive-on ramps, approx. 2,750 x 600 mm (collapsible to 20 mm) * Hydraulic flow divider in the trailer (for hydraulic pump output on the truck of over 40 l/min up to max. 140 l/min) ----Painting: * Chassis, drawbar, bulkhead, mechanical drop supports and drive-on ramps hot-dip galvanized * Axles, springs, air reservoirs, landing gear front, and flange hitch eye painted in black shade * Drop sides painted in RAL 9010 pure white * Painting of the side walls in a RAL color of your choice available at extra charge ----Information: * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available immediately ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting/lowering system and RtR valve * Smard board for payload weighing * Warning sign kits, front and rear * Reflective contour tape on the sides and rear * Removable rotating beacon (rear) * LED lighting * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated steel sheet and basket-type spare wheel holder, mounted right side * Front: closed single plastic mudguard * Rear: straight steel mudguards, each with spray suppression * Side underrun protection * Bogie platform extension by 520 mm with 45° corners, 3 integrated lockable storage compartments with lids * Chassis made of high-strength fine-grained steel * 50 mm softwood floor over bogie platform, 60 mm softwood on low-bed platform * Outer rails on ramps made of hardwood * 4 stake pockets per side (no stakes included); 2 t lashing possible at each * Load securing package: 2 lashing eyes (6.4 t) front left/right on main frame of bogie platform * 2 pairs of lashing rings (13.4 t) on outer frame front/rear per side; 4 pairs of lashing rings (10 t), swing-out and lowerable per side (front/rear) * All lashing points loadable in all directions and recessed into outer frame * 2 pairs of lashing rings (6.4 t) in excavator arm rest area * 8 pairs of galvanized folding outriggers for 3 m overall width (not at rear slope) * Extension planks stored left side in a storage box * Excavator arm rest above rear axle to end of rear slope, approx. 2,100 x 740 x 190 mm * Rear mechanical fall supports * Hydraulic folding ramps with hydraulically adjustable ramp tip, approx. 4,650 x 720 mm, incl. hydraulic lateral ramp adjustment & load-holding valve * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Loading height loaded approx. 890 mm, +/-20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, bogie, ramps, outriggers and mechanical fall supports hot-dip galvanized * Axles, drawbar, air reservoir and turntable in black finish * Tires: 235/75 R 17.5 * New vehicle, no initial registration, manufacturer’s warranty Kjdsl Tik Nepfx Ab Ssnb * Subject to errors and prior sale * Immediately available ex Egestorf, A7

Stanje: novo, največja dovoljena obremenitev: 10.900 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, ETÜ-TA-R 14.4 ----Brake System: * EBS electronic braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Air suspension ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm up to 2,250 mm * 40 mm flange towing eye ----Lighting / Electrical: * TPMS (Tire Pressure Monitoring System) * LED tail lights 12 / 24 V * 15-pin power connector ----General Attachments: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding supports at the rear * Plastic toolbox mounted externally at the front right on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood floor * Preparation in front of the bulkhead for retrofitting container locks * Bolted smooth sheet metal bulkhead * Trapezoidal-profiled, fold-down steel side walls with drop-side spring assists * Steel rear wall, can be stowed between the ramp holders when not in use, inside in front of the bulkhead * Bolted rear stanchions Kodpeq Dyvyofx Ab Sjnb * Rear drive-on slope approx. 860 mm ----Load Securing: * Perforated outer frame, edged at approx. 45 degrees with 2 t lashing capacity every 480 mm * Installation of 3 t fold-down lashing rings possible every 600 mm * 1 x 6.3 t lashing ring at each front and rear corner * Various holes for 1.2 t lashing options in bulkhead and rear crossmember ----Ramps: * One-piece mechanical grating drive-up ramps with spring mechanism for one-man operation, approx. 2,750 x 600 mm (collapsible down to 20 mm) ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, bulkhead, rear wall, tailgate, and drive-up ramps * Side wall color in RAL 9010 pure white * Painting of side walls in any RAL color available at extra cost ----Info: * — Reinforced and certified body according to EN 12642 XL including load securing certificate — * New vehicle with manufacturer warranty * Errors and prior sale excepted ----Delivery time: * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 20.500 kg, skupna masa: 27.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TR 27.0 Platform: * EBS (Electronic Braking System) * Emergency release system for spring-loaded brake cylinders * Drum brakes * 3 x 9 t BPW Eco axles Knsdpfx Ajr Dpzxsb Sob * Air suspension with lift and lowering device including RTR function * First axle liftable * Last axle is self-steering trailing axle with electro-pneumatic steering lock via reverse gear PIN (Steering lock for trailing axle activated from the tractor for maneuvering purposes—no truck-side installation required—wired to PIN 10 in the 15-pin connector, only for maneuvering and not for use on public roads) * SmartBoard control unit as infotool with pressure sensors for displaying total axle load * Tire pressure monitoring with readout in the truck via EBS signal, no truck-side installation required * Fixed center drawbar with 50 mm flange drawbar eye (loaded 900 mm, mm height adjustment at the head plate) * Mechanical landing gear at the front, mechanical swivel supports at the rear chassis * Hydraulic flow divider * Continuous side walls (without center stanchion) up to the drive-on slope * Folding rear stanchions * Steel rear wall slotted in before rear stanchions * Mechanically adjustable warning panel kit front and rear * Toolboxes made of galvanized steel sheet—black powder-coated—approx. 650 x 300 x 600 mm, right side * 15-pin power connector * LED tail lights * Removable LED rotating beacon incl. bracket and installation * 2 x LED reversing lights at vehicle rear (activated via reverse gear) * Flashing LED side marker lights * 60 mm larch/douglas fir wooden floor * 400 mm steel front wall slotted in * Perforated outer frame approx. 45° angled with provisions for mounting 3 t folding lashing rings * In each corner: 1 x 10 t lashing ring, plus 2 x 10 t and 3 x 6.3 t lashing rings on each side * Various holes for 1.2 t lashing points in front and rear crossmembers * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm, mechanically adjustable sideways * 4-circuit hydraulic control block for potential retrofit of hydraulic ramp shifting * Chassis, drawbar, front wall, mechanical rear supports, and loading ramps hot-dip galvanized * Axles, air tanks, flange drawbar eye, and front landing gear painted in black * Hydraulic flow divider in the trailer (for hydraulic pump output in truck from over 40 l/min up to 120 l/min) * New vehicle with manufacturer warranty * Subject to error and prior sale * Available immediately ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.360 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-ER 14.4: ----Brakes: * Electronic Brake System (EBS) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * Gigant axles ----Suspension: * Air suspension with lift and lower facility ----Drawbar / Flange Eye: * Drawbar height adjustable by approx. 300 mm * 40 mm flange drawbar eye ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System with in-cab display via EBS signal; no truck-side installation required) * LED lighting system * 15-pin power connector ----General Attachments: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding support legs at the rear Knodpfspk D Dqox Ab Ssb * Plastic toolbox, front right, mounted outside on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * 50 mm softwood flooring * Provision for retrofitting 20" container locks at front and rear * Bolted bulkhead made of smooth sheet steel * Fold-down side walls, trapezoidal profile, with drop-side spring assists * Bolted, hot-dip galvanized rear stanchions ----Load Securing: * Outer frame with holes, approx. 45° angled, 2 t lashing capacity every 480 mm * Option to install 3 t recessed lashing rings every 600 mm * Each of the front and rear corners fitted with 1 x 6.3 t lashing ring * Various holes in front and rear cross members for 1.2 t lashing options ----Ramps: * 1 pair of aluminium loading ramps, approx. 3,310 x 400 mm (load capacity 8 t per pair), suitable for pneumatic and tracked vehicles; stowed at the rear in a compartment integrated below the deck in the chassis ----Paintwork: * Hot-dip galvanized chassis, drawbar, bulkhead, and rear wall * Vehicle fully hot-dip galvanized ----Information: * New vehicle with manufacturer’s warranty * Subject to error and prior sale ----Delivery Time: * Available immediately ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 38.620 kg, skupna masa: 50.000 kg, konfiguracija osi: > 3 osi, Leto izdelave: 2026, T5 Profile 50.0: ----Braking System: * Wabco EBS (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (when lifted, ride height +30 mm) * Last axle is self-steering (lockable from the cab for maneuvering purposes without any installation on the truck side, and additionally via a switch on the trailer). The lock must be disengaged before driving on public roads. * Forced lifting and lowering of the lift axle for maneuvering (truck-side installation required), with speed-dependent control via the EBS electronics ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: Drawbar 1,500 mm long with 50 mm draw eye and manual height adjustment Knedpfx Absxptn Ds Sjb ----Electrics / Lighting: * Smartboard as an info tool with pressure sensors for axle load indication per axle group * Tire pressure monitoring with display in the truck via EBS signal (without truck-side installation) * LED lighting system 12/24 V * LED rotating beacon (removable), rear ----General Fittings: * Mechanical warning sign set for 3 m total width * Toolbox made of galvanized steel plate approx. 650 x 300 x 600 mm, mounted left side * Plastic fenders front axle and galvanized steel mudguards rear axle ----Low Loader Platform: * Front section of turntable platform with 45° corners and 3 stowage compartments with lockable folding lids (folding towards the rear) * Shortening of the low-bed platform by 500 mm to 6,280 mm including extended recess by 500 mm at the front * Rubber covering on the folding frame, approach ramp, and running surface of the low-loader platform * Bamboo wood between the longitudinal beams, in front of the excavator stick rest area ----Load Securing (LaSi Package): * 2 x 6.4 t lashing eyes in the front corners * 2 x 13.4 t UVV lashing points on each side in the front and rear corners * 5 x 10 t UVV lashing rings on each side (swivelable and lowerable, loadable in all directions) * 4 stake pockets per side with simultaneous 2 t lashing option * 1 x 16 t UVV lashing ring on the rear crossmember ----Width Extension: * Extendable and foldable width supports for 3 m total width (plank holder under the chassis, right side) ----Excavator Stick Rest: * Continuous excavator stick rest with reinforcement profile from last axle to end beam approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on the sides of the excavator stick rest ----Ramps: * Hydraulic folding ramp with dual-circuit hydraulics and folding tip approx. 4,650 x 720 mm, including load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (for hydraulic pump outputs on the truck over 40 l/min up to max. 140 l/min) ----Loading Height: * Loaded: 890 mm +/- 20 mm adjustable via air suspension ----Loading Area Dimensions: * Platform above turntable: 2,600 + 390 x 2,520 mm * Low-bed loading platform: 6,280 + 500 x 2,520 mm, incl. 860 mm approach ramp ----Paintwork: * Chassis, turntable, drawbar, width extension consoles, ramps hot-dip galvanized * Drawbar yoke, axles, hydraulic axle supports and air tanks painted in black ----Information: * New vehicle with manufacturer warranty * Subject to prior sale and errors ----Delivery Time: Available immediately*

Stanje: novo, največja dovoljena obremenitev: 17.650 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.230 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TP 30.0 with 3 cable drum supports ----Braking system: * Wabco TEBS (electronic brake system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11-tonne Gigant axles ----Suspension: * 17.5" air suspension with lift and lowering device ----Drawbar: * 1,800 mm long drawbar with 40 mm towing eye ----Electrics / Lighting: * Tyre pressure monitoring with display option in the truck display via EBS signal (no truck-side installation required) * 15-pin power connector * 2 additional LED reversing spotlights (switched via reverse gear) * LED lighting ----General fittings: * Aluminium air tank * Stainless steel toolbox on the side, approx. 1,000 x 300 x 600 mm * Side underrun protection * Plastic quarter mudguards * Rear underrun protection ----Platform: * Zurr-fix outer frame bent at 45°, hole pattern for lashing equipment, lashing force per lashing point 2,000 kg at a spacing of 480 mm * Installation of 3,000 kg drop lashing brackets at approx. 600 mm spacing possible – each side is equipped with 12 pcs. 3,000 kg lashing brackets included in delivery * Each side has 5 pockets for 100 x 50 mm stake posts in the outer frame – stakes not included in delivery * 30 mm phenolic resin-coated plywood floor ----Drum supports: * 3 pcs. galvanised drum supports secured by container locks with side forklift pockets center/center 800 mm (pocket width 185 mm) * Max. drum diameter 2,600 mm and max. drum width 1,650 mm * Clear width between support arms approx. 1,775 mm, with cross-bracing * Permissible drum weight per cable support 6,000 kg * Without drive and drum brake * Support arm with clamping lock for securing drum shaft * Steel drum shaft 76 mm diameter, with centring and rotating ends * 2 locating rings * 2 centring cones made of polyamide * 4 pcs. 3.2 t lashing eyes on the support arms for securing the drum against rotation and uncoiling by the customer ----Loading height: * Approx. 1,040 mm loaded ----Paintwork: * Chassis, turntable, drawbar, outer frame, underrun protection hot-dip galvanised * Axles painted in a shade of black ----Information: Ksdpfxjx Nli Ns Ab Sjnb * Technical upgrade to 30 tonnes GVW possible * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available from week 51/2026

Stanje: novo, največja dovoljena obremenitev: 30.440 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, Leto izdelave: 2026, Oprema: ABS, T 4 Profi 40,0 ----Zavore: * Wabco EBS-E (električni zavorni sistem) * Naprava za hitro sprostitev zavore za vzmetne akumulatorske cilindre * Bobnaste zavore ----Osi: * 4 x 11 ton Gigant osi ----Vzmetenje: * Zračno vzmetenje z dvigalom in spuščanjem ter ventilom za ohranjanje višine ----Vlečna naprava: * Naravna vlečna naprava s 50 mm vlečno oglico in nastavljivo višino ----Elektrika / Osvetljava: * Sistem za nadzor tlaka v pnevmatikah z možnostjo prikazovanja na zaslonu tovornjaka preko signala EBS – brez dodatne namestitve na tovornjaku * SmartBoard kot informacijsko orodje z dajalniki tlaka za prikaz obremenitve osi na vsaki skupini osi * 15-polni vtič * LED zadnje luči * LED luči za osvetlitev vseh strani (odstranljive) zadaj ----Splošni dodatni deli: * Paketi opozorilnih tabel spredaj in zadaj * 2 x orodjna omara iz pocinkane, prašno lakirane jeklene pločevine, približno 650 x 300 x 600 mm, na desni strani * Spredaj zaprt, plastičen, posamični blatnik * Zadaj naravna jeklena ščitnika za blatnike, vsak z zaščito proti brizganju (zmanjševanje brizganja) * Stranski zaščitni sistem ----Nizka platforma: * Podaljšana platforma z vrtljivo podvozi za 520 mm, z 45° koti in 3 vgrajenimi predali z pokrovi, ki se lahko zaklenejo * Talna obloga nad platformo z vrtljivo podvozi iz 50 mm, v nizki platformi pa iz 60 mm iglavca * Gumijasta obloga 20 mm namesto lesene talne obloge na območju teka, z dolžino nizke platforme 6.780 mm, vključno z rampo za vožnjo * Gumijasta obloga na rampi za vožnjo, levo in desno, dolžine približno 860 mm * Na vsaki strani 4 žepi za nosilce (vendar nosilci niso vključeni), hkrati pa omogočajo pritrditev tovora z 2 tonami * Hidravlično nastavljivi stranski raztezniki za 3 m širine (vendar ne na zadnji rampi) * Stranske deske za razširitev, shranjene v predalu * Nosilec za roko bagra nad zadnjo osjo do konca rampe za vožnjo, približno D=2.100 mm x Š=740 x G=190 mm * 2 para pritrdilnih točk 6,4 tone, stransko v nosilcu za roko bagra ----Podvozje: * Podvozje iz visoko trdnega jekla z drobno zrnato strukturo ----Pritrditev tovora (paket Lasi): Platforma z vrtljivo podvozi: * 2 para 13,4-tonske pritrdilne točke v zunanjem okvirju platforme z vrtljivo podvozi Nizka platforma: * Na vsaki strani 4 pare 10-tonske pritrdilne točke na zunanjem okvirju, ki se lahko spustijo in so obremenljive v vse smeri * Na zadnji strani, na vsaki strani 2 para pritrdilnih točk 13,4 tone, vrtljivih Knjdpoylfvgofx Ab Seb ----Rampe: * Gumijasta obloga na zložljivih rampah za vožnjo * Hidravlično zložljive rampe z hidravlično nastavljivim vrhom, približno 4.650 x 720 mm * Hidravlična stranska premika rampe in ventili za zadrževanje tovora ----Zadnji opornik: * Hidravlični zadnji opornik ----Razširitev: * 8 parov pocinkanih zložljivih podaljškov za 3 metre skupne širine (vendar ne na zadnji rampi) * Stranske deske za razširitev, shranjene v predalu ----Nosilec za roko bagra: * hidravlična enota za razdelitev pretoka v prikolici (pri hidravlični moči črpalke v tovornjaku nad 40 - največ 120 l/min) ----Mere za nakladanje: * zadnja nakladalna površina: približno 6.780 x 2.520 mm (vključno z rampo za vožnjo 860 mm) * nakladalna površina nad vrtljivim obročem: približno 2.990 x 2.520 mm ----Višina nakladanja: * približno 890 mm, +/- 20 mm ----Barvanje: * Reflektirajoči obrobni trak na straneh in zadnji strani * Podvozje, vrtljiva platforma, rampe za vožnjo in zložljivi podaljški, vroče pocinkani * Osi, vlečna naprava, zračni rezervoar in vrt

Stanje: novo, največja dovoljena obremenitev: 2.110 kg, skupna masa: 2.700 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 3.050 mm, širina tovornega prostora: 1.550 mm, višina nakladalnega prostora: 200 mm, B27300/150 MACHINE TRANSPORTER TECHNICAL DATA * Trailer type: B27300/150 * Gross vehicle weight: 2,700 kg * Payload: 2,075 kg * Internal dimensions: L: 305 cm, W: 155 cm, H: 20 cm * Loading height: approx. 54 cm * Floor: multiplex wooden floor * Integrated lashing points recessed in the loading floor * Side walls: steel * Frame: welded steel, hot-dip galvanized by immersion * Electrics: 13-pin, 12V * Tyres: 185R14C * Axle manufacturer: AL-KO or KNOTT * Number of axles: 2 * Braked axles * Standard jockey wheel Ksdpfx Asthlrhsb Sonb * Walkable steel mudguards * Shovel holder * Rear support stands * Loading ramps – 200 cm plus vehicle registration document/COC certificate €39.00 All prices include VAT. Images may not correspond to the standard equipment. Technical changes (e.g. tyre sizes) reserved. Delivery: Delivery by forwarding agent possible, €1.50 per transport kilometre one-way throughout Germany (from Seesen to the destination), at least €270 plus VAT. Visit us also at Here you can also order your desired trailer and accessories upon request: BLYSS Transporttechnik GmbH Dieselstr. 8 85084 Reichertshofen Tel.: BLYSS Transporttechnik GmbH Burenkamp 18-20 46286 Dorsten - Wulfen Tel.: FINANCING OR LEASING POSSIBLE* Vehicle number (for customer inquiries) Images may not correspond to standard equipment. Technical changes (e.g. tyre sizes) reserved.

Stanje: novo, skupna masa: 1.500 kg, konfiguracija osi: 1 os, dolžina tovornega prostora: 3.750 mm, širina tovornega prostora: 2.200 mm, višina nakladalnega prostora: 2.300 mm, Trade Fair Trailer Event Promotion HBA375 Please use 0566 for inquiries. Knsdpsxw Dt Tofx Ab Sob * Permissible total weight: 1500 kg * Internal dimensions: 375x220x230 cm * Chassis: single-axle, high-loader, steel/galvanized with 4 retractable support legs * 10-inch tires * Automatic reverse mechanism and jockey wheel * 13-pin connector plug * Superstructure: white UV-resistant polyester sandwich panels, white painted profile strips * Walls and ceiling approx. 25 mm thick * Full-depth side flap on the right (in direction of travel) * Folding aluminum staircase with railings/handrails on both sides, including flag holder slots Plus €39 gross for vehicle documents/COC. We will send these by registered mail or hand them over in person upon receipt of (down) payment. Please contact us before visiting, as this trailer may already be sold despite our large on-site stock. By phone, you can find out if your desired trailer is immediately available – we are happy to also order new units to your specifications (dimensions, weight, equipment, etc.). Due to the large number of trailers in stock, mistakes can occasionally occur – please bear with us. Information regarding specifications and prices may contain errors.

Stanje: novo, največja dovoljena obremenitev: 30.080 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – without truck-side installation * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning panel packages front & rear * SmartBord infotool installed with pressure sensors for total axle load display per axle group * Reflective contour tape on the sides and rear * LED rotating beacon (removable) at the rear Knjdpfx Aboxmpydj Seb * 15-pin power connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front closed single plastic mudguards * Straight rear steel mudflaps, each with spray suppression * Side underrun protection * Superstructure in front of the bogie platform approx. 520 mm with 45° corners and 3 storage compartments including lockable folding lids (folding lids opening to the rear) * Chassis made from high-strength fine-grained steel * Floor over the bogie platform made of 50 mm softwood, and 60 mm softwood in the low loader platform * Outer planks of the drive-on ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing eyes 6.4 t front left and right on the main frame of the bogie platform, 1 pair each of 13.4 t lashing rings at the front and rear outer frame, 1 pair each of 10 t lashing rings, swiveling and lowerable, loadable in all directions and recessed in the outer frame, 5 t lashing rings bolted to the outer frame of the wheel recesses (2 at the front recess, 1 at the rear), 2 pairs of 6.4 t lashing rings on the excavator stick holder * 11 pairs of folding outriggers for a total width of 3 meters (not at the rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for the widening boards made of sheet steel, mounted transversely to the loading area in front of the first rear axle * Excavator stick holder above the rear axle up to the end of the approach slope approx. 2,300 x 740 x 190 mm * Two wheel recesses per side approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with retractable cover (storage for covers at the front on the bogie platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm * Hydraulic lateral ramp shift * Loading area over the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loading height loaded approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, bogie, folding outriggers, rear drop-down supports, and drive-on ramps galvanised * Axles, air tanks, and drawbar painted in black * Tires: 235/75R17.5 * Vehicle is galvanised * New vehicle with manufacturer’s warranty * Errors and prior sale reserved * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 11.400 kg, skupna masa: 15.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 12.000 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 850 mm, skupna širina: 2.550 mm, Leto izdelave: 2026, Metal-Fach T009 Bale Trailer 3-Axle Platform Trailer Flatbed Trailer New Vehicle Year of Manufacture: 2026 Overall dimensions: 11990mm + 800mm x 2480mm x 2900mm Internal dimensions: 9300mm + 800mm x 2380mm x 1875mm Gross weight: 15,000 kg Unladen weight: 3,560 kg Payload: 11,440 kg Loading height: 1,160 mm Tyres: 500/50-17 Extendable loading platform Wide tyres Air brake system Load-dependent brake force regulator (ALB) Side underrun protection Side lighting Parabolic suspension Parking brake Adjustable front and rear loading grids Y-drawbar 40 km/h road approval possible Mudguards Custom paint available !!! ATTENTION – PLEASE READ !!! We expressly reserve the right to prior sale, as this item is also listed on other platforms. We strongly recommend inspection and verification to avoid any misconceptions regarding condition and suitability. Viewings and inspections are possible at any time by appointment and are expressly encouraged!!! Images are for illustration purposes and may show optional accessories at additional cost. The internal dimensions stated are approximate values. TRADE-INS POSSIBLE FOR ALMOST ANYTHING!!! PART-EXCHANGE DEALS AND SURCHARGE POSSIBLE!!! Showground: 58285 Gevelsberg, Am Sinnerhoop 17 Opening hours: Monday – Friday 8:30 am to 5:00 pm, Saturday 8:30 am to 2:00 pm Always over 500 new and used trailers in stock!!! Knodstw N D Sjpfx Ab Ssb Pegasus Anhänger GmbH Am Sinnerhoop 17 58285 Gevelsberg Tel.: Fax:

Stanje: novo, največja dovoljena obremenitev: 9.000 kg, skupna masa: 11.600 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 9.080 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 850 mm, skupna širina: 2.550 mm, Leto izdelave: 2026, Metal-Fach T014/2 Bale Trailer 2-axle Platform Trailer Flatbed Trailer New vehicle Year of manufacture: 2026 Overall dimensions: 9089mm + 800mm x 2520mm x 2880mm Internal dimensions: 6409mm + 800mm x 2380mm Loading height: 1150mm Gross weight: 11,600kg Empty weight: 2,600kg Payload: 9,000kg Tyres: 400/60-15.5 Extendable loading platform Wide tyres Air-braked ALB valve Side underrun protection Side lighting Parabolic suspension Parking brake Adjustable front and rear loading gates Y-drawbar 40km/h road approval possible Mudguards Custom paint possible IMPORTANT!!!! PLEASE READ!!!! We expressly reserve the right of prior sale as this item is also advertised on other platforms. We strongly recommend an inspection and review to avoid any misunderstandings regarding the condition or suitability of the item. Viewings and inspections are possible at any time by appointment and are expressly encouraged!!! Images are similar and may show accessories subject to an extra charge. All internal dimensions are approximate. TRADE-INS POSSIBLE FOR ALMOST EVERYTHING!!! PART-EXCHANGE AND ADDITIONAL PAYMENT POSSIBLE!!! Showground: 58285 Gevelsberg, Am Sinnerhoop 17 Opening hours: Monday–Friday 8:30 am to 5:00 pm, Saturday 8:30 am to 2:00 pm Always over 500 new and used trailers in stock!!! Pegasus Anhänger GmbH Knedshlr Rdjpfx Ab Sjb Am Sinnerhoop 17 58285 Gevelsberg Tel.: Fax:

Stanje: rabljeno, največja dovoljena obremenitev: 14.170 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 02/2006, dolžina tovornega prostora: 6.530 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.000 mm, skupna širina: 2.550 mm, Skupna masa: 18.000 kg Lastna masa: 3.830 kg Nosilnost: 14.170 kg Skupna dolžina: 8.550 mm Dolžina nakladanja: 6.530 mm Širina: skupna širina 2.550 mm / širina nakladanja 2.540 mm Višina nakladanja: pribl. 1.000 mm Dodatne informacije Kodpfx Asw N A Eyjb Ssnb - Tla iz trdega lesa z Omega profili - Stranske stranice prisotne - Dvojna kolesa - BPW osi - Prstani za privezovanje - LED vzvratne luči