Müller-Mitteltal Zamenljivo Ohišje nakup rabljenega (256)

Stanje: novo, največja dovoljena obremenitev: 30.500 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Tire pressure monitoring with display capability in the truck via EBS signal - no on-truck installation required * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning sign packages front & rear * SmartBord infotool mounted with pressure sensors for total axle load display per axle group * Reflective contour tape on the sides and rear * Removable LED beacon at the rear * 15-pin power connector Iedexmpydjpfx Ab Uebf * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front closed individual plastic mudguards * Rear straight steel mud flaps each with spray suppression * Lateral underrun protection * Front section ahead of the turntable platform extended approx. 520 mm with 45° corners and 3 storage compartments incl. lockable folding lids (folding lids open to the rear) * Chassis made of high-strength fine-grained steel * Floor over the turntable platform made of 50 mm and in the low-bed platform made of 60 mm softwood * Outer planks of the loading ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing rings 6.4 t front left and right on the main frame of the turntable platform, 1 pair of 13.4 t lashing rings per side at the front and rear on the outer frame, plus 1 pair of 10 t lashing rings per side swivel- and lowerable, loadable in all directions and recessed in the outer frame, bolted 5 t lashing rings to the outer frames of wheel recesses (2 for the front and 1 for the rear wheel recess), 2 pairs of 6.4 t lashing rings at the side in the excavator arm recess * 11 pairs of folding outriggers for 3 m overall width (not at the rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for the extension boards made of sheet steel, mounted across the loading area in front of the 1st rear axle * Excavator arm trough above the rear axle to the end of the approach slope approx. 2,300 x 740 x 190 mm * 2 wheel recesses per side, approx. 640 mm wide - front 340 mm deep, rear 220 mm deep - with retractable cover (storage for covers at the front of the turntable platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically extendable tip part approx. 4,650 x 720 mm * Hydraulic lateral ramp shift * Load platform above the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded platform height approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, turntable, folding outriggers, rear drop-down supports and loading ramps hot-dip galvanized * Axles, air tanks, and drawbar painted in black * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Errors and prior sale excepted * Available from CW 14/2026 * Sample images

Stanje: novo, največja dovoljena obremenitev: 14.300 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 4.995 mm, širina tovornega prostora: 2.380 mm, višina nakladalnega prostora: 900 mm, Oprema: ABS, Müller? Mitteltal KA-TA-R 19 Tandem Tipping Trailer with Bordmatik Left Side Inquiry Number: 11573 * BRAND NEW VEHICLE now finally available for immediate delivery!!! * Delivery free to your premises upon request. * Financing available through our partners FM LeasingPartner or MMV Leasing with terms from 24 to 72 months, with or without down payment, with or without final residual value. * Example: 60 months with no down payment and no residual value – €769 / month * Request your individual quote from us! We are an official Müller Mitteltal dealer. * ---- * Gross weight: 19t, Payload: 14.30t, RAL 9016 traffic white or custom paintwork upon request * Reinforced and certified body built to EN 12642 XL including load securing certificate * Body – Steel 4,995mm x 2,380mm x 900mm * Right side with spring-assisted steel tailgate (2 springs), rear wall steel * Left side with Müller Bordmatic hydraulic sideboard (Bordmatik) * Removable roll tarpaulin for tipper * 4 pairs of lashing rings, recessed and foldable in 5mm steel floor, LC 3000 daN * LED lighting system 12+24 Volt replacing standard lighting * 2 LED reversing lights * Side marker lights with indicator function * BPW Eco axles, air suspension, drum brakes * 385/65R 22.5 tyres, with TPMS, EBS 2S/2M * 4 semi-round mudguards * Chassis, drawbar and foldable rear underrun protection hot-dip galvanized * Front wall platform with galvanized access step * Drawbar with 50mm eye, adjustable by +77mm / +33mm * Front support leg with crank * Foldable underrun protection for paver feeding * Removable protective grille for tail lights * ---- * Our business hours Iedpfxowq Uihs Ab Usbf * Monday – Thursday: 08:00 – 17:00 * Friday: 08:00 – 15:00 * Outside business hours, appointments available by arrangement * We speak German, English, Russian, Polish, French * Leasing, financing, trade-in possible

Stanje: rabljeno, lastna masa: 4.120 kg, največja dovoljena obremenitev: 13.880 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 03/2016, naslednji pregled (TÜV): 02/2026, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.360 mm, višina nakladalnega prostora: 900 mm, prostornina tovornega prostora: 10 m³, vzmetenje: zrak, velikost pnevmatike: 385/65R22.5, barva: rdeča, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Lokacija vozila: Bovenden, 2 osi, BPW osi, tandem, zračno vzmetenje, ABS (sistem proti blokiranju koles), zaščita proti podvozu, prednja opora, nihajna vrata. Nadgradnja: Tandemska prekucna prikolica z aluminijastimi stranicami, cca 10 m³, 2x 9t BPW osi, bobnaste zavore! Višina nakladanja cca 1510 mm! PODATKI O DODATNI OPREMI BREZ GARANCIJE, spremembe, vmesna prodaja in napake pridržane! Ibsdpfx Abexfli Ej Uef

Stanje: rabljeno, prva registracija: 11/2006, Leto izdelave: 2006, MÜLLER - MITTELTAL T4 Kompakt Vrtljiva prikolica - Nizkopodna prikolica z zračno vzmetenimi in jamskimi kolesi - 4 x zračno vzmetene GIGANT - osi - zračno vzmetenje - 4 x kolesne jame - mehanske nakladalne rampe - 2 zadnja podporna noga, zložljiva - izvlečne opozorilne table - ABS - MICHELIN pnevmatike: 235/75 R 17.5 - težka izvedba: 40.000 kg skupne mase - lastna teža: 8.400 kg - skupna dolžina: 11.750 mm - vlečna zanka: 50 mm Posebej primerna za prevoz strojev za rezanje apna! Isdpfx Aswmpbdeb Usbf - nemška prikolica - Tehnični pregled / tehnični preizkus možen na zahtevo in za doplačilo! Pridržujemo si pravico do napak in vmesne prodaje!

Stanje: rabljeno, številka stroja/vozila: 217, lastna masa: 3.450 kg, največja dovoljena obremenitev: 14.550 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 01/1993, vzmetenje: jeklo, velikost pnevmatike: 385/65 r22,5, medosna razdalja: 5.300 mm, barva: oranžna, Oprema: ABS, Drum brake Subject to errors and omissions Ibedpfxsnh Rzyj Ab Usf

Stanje: rabljeno, številka stroja/vozila: 39500, lastna masa: 8.250 kg, največja dovoljena obremenitev: 31.750 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/1995, velikost pnevmatike: 235/75 r17,5 zwilling, Leto izdelave: 1995, Further information Main and outer frame made of high-strength double-T sections, grade ST 52.3, quadruple longitudinal profiling, with high-webbed front and rear cross-members as well as transverse braces; frame behind the bogie passage features a gently sloping stepped offset and rear loading bevel, 0.8 m long; lowest possible floor height achieved by recessed wheel wells above the rear wheels; leading edges of the bogie platform beveled at 45 degrees. Two recessed UVV lashing rings each on the bogie platform and loading bevel for attaching securing devices. Rear end fitted with wide supports for a ramp shaft with six-fold bearings. Lateral side protection fitted with an EC-compliant guard rail, wheel chocks with clamp lock. Low-maintenance inclined roller bearing axles with automatic linkage adjusters, two-line pneumatic braking system in accordance with EC regulations, and parking brake. Bogie and drawbar: Constructed from double-T sections in welded design with ball-bearing turntable; standard drawbar length 1,500 mm, with 8 eyelets (50 mm diameter each), drawbar support with threaded spindle as height adjustment device. Vehicle is not fitted with axle compensation! 24 volts, 2 exchange-proof 7-pin connection cables, large rectangular four-chamber lights including rear fog and reversing lights, front distribution box, rear outline marker lights, side marker reflectors, and holder for single-line license plate. Undercarriage made of 40 mm thick, pressure-impregnated pine. Low-loader platform and loading bevel with cross-laid top flooring, 30 mm thick, running lengthwise. Total floor thickness 70 mm. Bogie platform with longitudinal single-layer flooring and recessed open tool box, size L 700 x W 800 x H 180 mm. Ramps: Welded construction with trough plate, transverse braces, longitudinally laid wooden overlay, 50 mm thick; ramp tips reinforced; ramp holding rods with turnbuckle and safety catch; ramps laterally adjustable by 470 mm each, with perforated rail and sliding tube; ramp shaft made of bright steel, articulated spring lifters with external and internal springs for easy one-person operation, with automatic ground supports. Ibedei Rixgspfx Ab Uof Shot-blasted with steel granulate, zinc phosphate-primed, painted in a single acrylic RAL color of choice; wheels silver. Available in traffic, light, and metallic colors as well as two-tone paint finishes; wood surface is stained.

Stanje: novo, največja dovoljena obremenitev: 30.500 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning sign packages at front and rear * SmartBord infotool installed with pressure sensors for total axle load display per axle group * Reflective contour tape on sides and rear * Removable LED beacon at rear * 15-pin electrical connector * LED tail lights * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Closed molded plastic single fenders at front * Straight steel rear fenders each with spray suppression (ant-splash) * Side underrun protection * Extension in front of the turntable platform approx. 520 mm with 45° corners and 3 storage compartments incl. lockable folding lids (lids open rearwards) * Chassis made of high-tensile fine-grained steel * Floor above turntable platform from 50 mm softwood, in low-bed platform from 60 mm softwood * Outer planks of ramps from 50 mm hardwood * Load securing package consisting of: 2 lashing eyes (6.4 t) at front left and right on main frame of turntable platform, 1 pair of lashing rings (13.4 t) at front and rear on side outer frame each, 1 pair of lashing rings (10 t) each side, pivoting and lowerable, loadable in all directions, recessed into the outer frame, 5 t lashing rings bolted to the outer frames at wheel recesses (2 each at front wheel recess, 1 at rear), 2 pairs of 6.4 t lashing rings at the excavator arm rest on the side * 11 pairs of folding outriggers for 3 m overall width (not in rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for ramp extension planks, made from sheet steel, transversely mounted in front of 1st rear axle * Excavator arm rest above rear axle to end of approach slope approx. 2,300 x 740 x 190 mm * 2 wheel recesses per side approx. 640 mm wide (front 340 mm deep, rear 220 mm deep) with slide-in covers (covers storage at front on turntable platform) for transporting wheel loaders with wheelbase 3,100–3,640 mm * Mechanical drop-down supports at rear * Hydraulic folding ramps with hydraulically extendable tip part approx. 4,650 x 720 mm * Hydraulic lateral ramp displacement * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded loading height approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, turntable, folding outriggers, rear supports, and ramps hot-dip galvanized * Axles, air tanks, and drawbar painted in black Ibsdpfx Aoxmpykob Ujf * Tires: 235/75R17.5 * Vehicle fully hot-dip galvanized * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from week 14 of 2026 * Sample images

Stanje: novo, največja dovoljena obremenitev: 11.000 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 1.000 mm, Leto izdelave: 2025, Oprema: ABS, dvižna zadnja plošča, * Müller-Mitteltal KA-TA-R 14.4 Tandem Low Loader Three-Way Tipping Trailer with Ramps – NEW VEHICLE * Immediately available in RAL 9016 traffic white * Leasing, financing, and trade-in of your old trailer possible ---- * Reference number for inquiries: 11563 * Remote Diagnostics Unit (RDÜ) with display option in the truck via EBS signal * Side marker lights with indicator actuation * Brake system EBS 2S/2M * Gross weight: 14.4t, Payload approx. 11t Ibedpfx Absxdp U Aj Usf * Galvanised floor * 5m x 2.42m x 0.5m + 0.5m steel side extensions (3-sided, swinging and foldable), painted, sidewalls laser welded * Lockable compartment under the tipping body for loading ramps * 1 pair of aluminium loading ramps 8t / pair, length 3.57m, included * Chassis hot-dip galvanised, front wall hot-dip galvanised * 4 UVV lashing rings LC 5000daN (front and rear) + 8 recessed, foldable lashing points LC 3000daN in the tipper bed (centrally positioned) * Excavator bucket rest made of hardwood * Two-step access ladder in front of the front wall (hot-dip galvanised) * Continuously height-adjustable drawbar, hot-dip galvanised, 40mm towing eye * Wide tires 385/55R 19.5 (4 tires), parabolic springs * Net hooks, rear stakes bolted on, hot-dip galvanised * Extension cables for the rear side wall * Plastic toolbox mounted on the right side of the chassis frame * LED lighting system 12 + 24 Volt * 2 LED reversing lights at the rear of the trailer ---- * Hire purchase price example: * e.g. €579/month for 60 months without down payment, no final payment. Offer provided by our financing partner "FM LeasingPartner". Other terms with/without final payment or down payment available * Request an offer from us! * We are official Müller-Mitteltal dealers ----Our Opening Hours Monday – Thursday: 08:00 – 17:00 Friday: 08:00 – 15:00 Outside opening hours, we are available by appointment We speak German, English, Polish, French WhatsApp / FaceTime

Stanje: rabljeno, Leto izdelave: 2014, Različni zabojniki za Müller-Mitteltal CHK: - 5 kosov 4,5 – 5 m³, cena na kos 1.000,- € Ibedpfexb N A Iex Ab Ujf - 3 kosi 8 m³, cena na kos 2.000,- € - 3 kosi 5,7 m³ z dvokrilnimi zadnjimi vrati, cena na kos 2.000,- € Vsi zabojniki so v uporabljenem, delujočem stanju. Leto proizvodnje: 2014 – 2015. = Dodatne informacije = Država proizvodnje: DE Za dodatne informacije se obrnite na Jan-Marc Schwickerta.

Stanje: rabljeno, številka stroja/vozila: 110, lastna masa: 8.320 kg, največja dovoljena obremenitev: 31.680 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2008, dolžina tovornega prostora: 10.300 mm, širina tovornega prostora: 2.550 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 r17,5, medosna razdalja: 6.500 mm, barva: modra, Oprema: ABS, * Drum brake * 4 axles * Wheelbase 6,500 mm * Hydraulic ramp length 2,850 mm – width 650 mm Ibodpslpav Uofx Ab Uof * Loading edge height 920 mm * Extendable to 3 m Subject to errors and omissions

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem equalizing unit * Tire pressure monitoring system with display capability in the truck via EBS signal, no installation required on the truck side * Height-adjustable drawbar (300 mm) with 40 mm flange towing eye * Mechanical landing gear at the front * Rear: 2 mechanical folding support legs * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * 15-pin electrical connector * Multi-chamber tail lamps * Bolted underrun protection * Plastic quarter mudguards * Mesh hooks on the sides and rear in the central locking mounts, plus 2 hooks on the front wall * Main frame made of fine-grain steel * Steel pallet - 2-way tipper body, fixed front wall made of smooth sheet, continuous side walls (foldable without center stanchions, with drop-side spring assist mechanism), pendulum-type operation via manual central locking * Rear stanchions are bolted * Steel rear wall slides in front of the ramps * In each corner: 1 x 5 t lashing point; additionally, 4 x 3 t lashing rings each side, integrated into the outer frame * 4 mm floor made of fine-grain steel Ibedpfjtr Sucex Ab Ujf * Two-piece mechanical grating loading ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (manually retractable to 80 mm) * Chassis, drawbar, rear stanchions, underrun protection, mechanical drop-down supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and landing gear painted in black * Drop sides and platform in RAL 9010 pure white * Painting of side walls and tipping platform in any RAL color available for extra charge * New vehicle with manufacturer's warranty * Subject to prior sale and errors * Available from CW 07/2026

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 2 x 7 ton Gigant axles * Parabolic springs with tandem compensation unit * Tire pressure monitoring with display capability in the truck via EBS signal, no installation required on truck side * Height-adjustable drawbar (300 mm) with 40 mm flange towing eye * Mechanical support winch at the front * Rear: 2 mechanical foldable supports * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * 15-pin electrical connector * Multi-chamber tail lights * Bolt-on underrun protection * Plastic quarter mudguards * Net hooks on sides and rear, integrated in the central locking bearings, plus 2 units on the front wall * Main frame made of fine-grain steel * Steel pallet 2-way tipper body with fixed smooth sheet front wall, continuous foldable side walls (without center stanchions, with sideboard spring lifters and manual central locking for swinging function) * Removable screw-on rear stanchions * Steel rear wall mounted in front of the ramps * In each corner: 1 x 5 ton lashing point; in each side: 4 x 3 ton lashing rings integrated into the outer frame * 4 mm floor made of fine-grain steel Ijdpfstr St Uex Ab Uobf * Two-part mechanical grating loading ramps with aluminum tapered end, 2,150 + 1,300 mm x 600 mm (retractable to 80 mm manually) * Chassis, drawbar, rear stanchions, underrun protection, mechanical supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and support winch painted in black tone * Side boards and platform in pure white, RAL 9010 * Painting of side walls and tipper platform in any RAL color available at additional cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from calendar week 07/2026

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-ER 14.4 Platform: * TPMS (Tire Pressure Monitoring System) * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 2 x 7-ton BPW axles * Air suspension with lifting and lowering system * Mechanically adjustable 3-meter warning panel sets, front and rear * Drawbar adjustable in height by 300 mm with 40 mm flange eye * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (thus B-dimension approx. 8,080 mm) * Landing gear/winch at the front * External foldable rear support legs * Plastic toolboxes approx. 750 x 350 x 300 mm each, on left and right sides * Side underrun protection * Rear underrun protection * Plastic quarter mudguards * 15-pin power plug * LED lighting system, 12 / 24 V * 2 additional LED reversing spotlights at the rear (wired via reverse gear) * 1 removable LED beacon (incl. bracket) at the rear * 400 mm high bolted front wall * 50 mm softwood flooring * 2 pairs of container locks (extendable to 3 m exterior container width) and lockable; locking dimension retracted according to ISO-DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not DIN-compliant) with a total exterior width of 3,000 mm * Perforated outer frame, approx. 45 degree angled, with 2 t lashing capacity every 480 mm, possible installation of 3 t folding lashing brackets every 600 mm – on each side, 5 x 3 t UVV lashing brackets installed –, at each front and rear corner 1 x 6.3 t lashing ring (front directly behind the container locks in the wooden floor and rear in the end crossmember), various holes for 1.2 t lashing options in the front wall and end crossmember * 1 pair of aluminum insert ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tired and tracked vehicles * Rear storage compartment integrated below the loading area in the chassis * ---Chassis, drawbar, front wall, underrun protection, and rear supports hot-dip galvanized--- Ibedpfx Asv D Tbdob Ujf * Axles, air tanks, front landing gear, and flange eye painted in black * New vehicle with manufacturer warranty * Subject to errors and prior sale * Available from week 09/2026

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tyre pressure monitoring system * Emergency release unit for spring-actuated brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting/lowering system and RtR valve * Smard on-board weight measurement system * Warning sign packages front & rear * Reflective contour tape on sides and rear * Removable rotating beacon at the rear * LED lighting * Straight drawbar with 50 mm towing eye and infinitely height-adjustable * Tool box made of powder-coated steel sheet and basket-type spare wheel holder, right-hand side * Front closed individual plastic fenders Ibjdpfx Abel Tik No Ujf * Rear straight steel spray guards with spray suppression * Lateral underrun protection * Turntable platform front extension by 520 mm with 45° corners and 3 recessed lockable storage compartments incl. covers * Chassis made of high-strength fine-grained steel * Turntable platform floor made of 50 mm and low-bed platform of 60 mm softwood * Outer planks of the drive-on ramps made of hardwood * Four stake pockets per side (stakes not included) and 2 t lashing point each * Lashing package comprising: Two 6.4 t lashing rings front left & right on the main frame of the turntable platform * Two pairs 13.4 t lashing rings at outer frame, front and rear, and four pairs per side 10 t lashing rings, swivel and height adjustable * Loadable in all directions and recessed into the outer frame * Two pairs 6.4 t lashing rings in the excavator arm rest area * Eight pairs galvanized folding outriggers for 3 m overall width (not in rear slope area) * Extension boards stored in a compartment on the left side * Excavator arm rest area above rear axle up to end of access ramp approx. 2,100 x 740 x 190 mm * Mechanical rear drop-down supports * Hydraulic folding ramps with hydraulically extendable ramp tips approx. 4,650 x 720 mm incl. hydraulic side-shifting ramps & load-holding valve * Deck area above slewing ring: approx. 2,990 x 2,520 mm * Rear load area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, turntable, drive-on ramps, folding outriggers, and mechanical drop-down supports hot-dip galvanized * Axles, drawbar, air tank, and slewing ring painted black * Tyres 235/75 R 17.5 * New vehicle without first registration, with manufacturer warranty * Subject to errors and prior sale * Available from CW 07/2025

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic brake system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting/lowering system and RtR valve * Smard-Board for load weight determination * Warning sign packages at the front & rear * Reflective contour tape on the sides and rear * Removable rear rotating beacon * LED lighting * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated sheet steel and spare wheel holder in basket design on right side * Front: closed single plastic mudguards * Rear: straight steel mud flaps with spray suppression * Side underrun protection * Turntable platform extended by 520 mm at the front, with 45° corners and 3 recessed, lockable storage compartments with lids * Chassis made of high-strength fine-grain steel * Decking over turntable platform made of 50 mm, and in low-bed platform of 60 mm coniferous timber * Outer planks of ramps made of hardwood * 4 stake pockets on each side (no stakes provided) with simultaneous 2 t lashing capability * Load securing package includes: 2 lashing eyes, 6.4 t, at the front left and right on the main frame of the turntable platform * On each side front and rear: 2 pairs of 13.4 t lashing rings on the outer frame and on each side 4 pairs of swiveling and lowerable 10 t lashing rings * Loadable in all directions, recessed into the outer frame * 2 pairs of 6.4 t lashing rings on the side in excavator arm recess * 8 pairs of galvanized folding outriggers for 3 m total width (not at the rear slope) * Widening planks stored in a side compartment on the left * Excavator arm recess over the rear axle to end of rear slope approx. 2,100 x 740 x 190 mm * Mechanical drop supports at rear * Hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm including hydraulic sideways ramp adjustment & load-holding valve * Loading deck over turntable: approx. 2,990 x 2,520 mm * Rear loading deck: approx. 6,780 x 2,520 mm * Load height loaded approx. 890 mm, +/- 20 mm (including 860 mm rear slope) * Flow divider installed * Chassis, turntable, loading ramps, folding outriggers, and mechanical drop supports hot-dip galvanized * Axles, drawbar, air reservoirs, and turntable painted in black * Tires: 235/75 R 17.5 * New vehicle, not previously registered, with manufacturer’s warranty * Errors and prior sale reserved * Available from CW 07/2026 Isdsl Tphrepfx Ab Uebf

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2025, * TS 3 Profile 30.0: * Wabco EBS-E (electronic braking system) * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco Plus axles * Air suspension with lift and lower system and RtR valve * Rear axle is self-steering with electro-pneumatic steering lock * Smartboard control box mounted as an information tool on the trailer, equipped with pressure sensors for total axle load display * Side underrun protection * Landing gears at front and rear with mechanical swing-down supports on the chassis * 15-pin electrical connector * LED lighting system 12/24V * Removable LED beacon on the rear left * Mechanically adjustable warning sign packages front and rear * Straight steel plate mudguards * Spare wheel holder on the right side under the chassis * Fifth wheel platform with 45° chamfered front corners and front-mounted toolbox made of galvanized steel (W = 2,480 x H = 500 x L = 665 mm) with folding lid * 400mm high aluminum side boards (RAL 9010 pure white), foldable and removable, on the fifth wheel platform * Rear wall – 150 mm – inserted high * Rear slope on the fifth wheel platform to low bed approx. 700 mm long * Fifth wheel platform with 50 mm wooden planks and low bed platform with 60 mm wooden planks * Tread plate over the axles * 8 x mechanical folding widenings to a total width of 3 meters, not at the rear slope (widening planks included, stored on the fifth wheel platform) Iedpfx Abol Tnvgj Ujbf * Load securing package: on the fifth wheel platform 2 x 6.3 t lashing rings per side, and 3 x 5 t lashing bars per side in the outer frame, in the low-bed platform per side 2 x 13.4 t lashing rings and 4 x 10 t folding/retractable lashing rings recessed in the outer frame, 2 x 6.4 t lashing eyes per side and 1 lashing ring in the excavator arm recess at the rear * Continuous excavator arm recess from the end of the last rigid axle over the steering axle to the end cross member, with internal reinforcement profiles (approx. L = 2,450 x W = 770 mm x D = 270 mm) * 2 x container locks directly after the neck in the low bed platform * Mechanically single-piece, hot-dip galvanized hydraulic loading ramps approx. 3,000 x 720 mm (mechanically adjustable laterally) * 4-way control block for future customer-side retrofit of hydraulic ramp shift * The outer board on the loading ramp is made of 50 mm hardwood * Hydraulic flow divider in the trailer (for truck hydraulic pump capacity from 40 l/min up to 120 l/min) * Loading area of the fifth wheel platform: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Unladen loading height approx. 910 mm (including 860 mm approach slope) * Saddle height approx. 1,220 mm (suitable for 2- and 3-axle tractors) * Chassis, ramps, rear folding supports, widening consoles hot-dip galvanized * Axles, landing gears, air tanks painted in a black tone * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Errors and prior sale excepted * Available from week 16/2026

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: * Wabco EBS-E (electronic braking system) Ibjdpfxspk D I Ao Ab Uof * RDÜ (tire pressure monitoring system) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco Plus axles * Air suspension with lift and lower function, as well as RtR valve * Last axle steering with electro-pneumatic steering lock * Smartboard control box mounted on the trailer as info tool with pressure sensors for total axle load display * Side underrun protection * Landing gear at front and mechanical swing-down supports at rear of chassis * 15-pin power connector * LED lighting system 12/24V * LED rotating beacon (removable) at rear left * Mechanically adjustable warning sign packages front and rear * Straight steel mudguards * Spare wheel holder underneath chassis, right side * Fifth wheel platform with 45° chamfered front corners and front tool box made of galvanized sheet steel, W = 2,480 x H = 500 x L = 665 mm with folding lid * Side of the fifth wheel platform equipped with 400 mm high aluminium drop-side boards (RAL 9010 pure white), foldable and removable * Removable rear wall – 150 mm high * Rear ramp on fifth wheel platform to lowbed, approx. 700 mm long * Fifth wheel platform fitted with 50 mm timber planks, lowbed platform with 60 mm timber planks * Chequer plate above the axles * 8 x mechanical foldable extensions to 3 m overall width (excluding rear ramp area), extension planks available with storage platform * Lashing package: On the fifth wheel platform, 2 x 6.3 t lashing rings each and 3 x 5 t lashing bars per side on the outer frame; on the lowbed platform, 2 x 13.4 t lashing rings per side plus 4 x 10 t lashing rings, pivotable and lowerable, fitted in the outer frame; 2 x 6.4 t lashing eyes per side plus 1 lashing ring in the excavator stick recess at rear * Excavator stick recess, running continuously from end of last fixed axle over the steering axle to the closing crossmember, with internal reinforcement profile, approx. L = 2,450 x W = 770 x D = 270 mm * 2 x container locks directly after the step in the lowbed platform * Mechanically operated one-piece hot-dip galvanized hydraulic ramps, approx. 3,000 x 720 mm (mechanically adjustable in width) * 4-way control block for later customer retrofitting of hydraulic ramp displacement * Outer board on ramp made of 50 mm hardwood * Hydraulic flow divider in the trailer (for truck hydraulic pump output from over 40 l/min up to 120 l/min) * Loading area of fifth wheel platform: approx. 3,935 x 2,480 mm * Lowbed loading area: approx. 8,500 x 2,520 mm * Loading height unladen approx. 910 mm (including 860 mm drive-on ramp) * Fifth wheel height approx. 1,220 mm (suitable for 2- and 3-axle tractor units) * Chassis, ramps, rear folding supports, widening consoles hot-dip galvanized * Axles, landing gear, air tanks painted in black * Hydraulic flow divider * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from week 16/2026

Stanje: novo, največja dovoljena obremenitev: 5.840 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2025, * KWH 8.8 ML: * TPMS (Tire Pressure Monitoring System) Ijdpou I Iqxsfx Ab Uebf * EBS braking system * Drum brakes * BPW axle * Parabolic springs * Support winch at the front * Spring-assisted square tube support legs at the rear with base plates and safety lock pins for various support heights * Drawbar with 40 mm bolt coupling (height-adjustable) * 15-pin electrical connector * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and cross members * Enclosed steel fenders with splash guards * Closed side underrun protection, usable as advertising space * Plastic toolbox with base insert (installed horizontally), approx. 500 x 350 x 400 mm * Swiveling cable drum assembly, clear width between the drum arms 1,700 mm, with tension lock for fixing the drum at the support arm ends, as well as a central claw lock for securing the cable drum assembly to the chassis * Motor-hydraulic drum drive with oil motor * Valves and adjustable drive rollers with rubber lining * Hydraulic speed regulator and brake for the drum drive * Steel drum shaft, 76 mm in diameter, with centering and rotating ends * 1 pair of stepped centering cones made of polyamide * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) * Finish: hot-dip galvanized * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 5.840 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2025, * KWH 8.8 ML: * RDÜ Tire Pressure Monitoring * EBS Brake System * Drum Brakes * BPW Axle * Parabolic Springs * Front Support Winch * Rear Square Tube Support Legs with Spring Assistance, Base Plate, and Safety Locking Pins for Adjustable Support Heights * Drawbar with 40 mm Bolt-on Eye (height adjustable, __ mm) * 15-pin Electrical Connector * LED Lighting * Flashing LED Side Marker Lights * Chassis made of torsion-resistant square tubes and cross beams * Enclosed steel mudguards with splash protection * Enclosed lateral underrun protection usable as advertising space * Plastic toolbox with floor insert (installed horizontally), approx. 500 x 350 x 400 mm * Swiveling cable drum carrier, clear width between drum arms 1,700 mm, with tension fastener for securing the drum to the carrier arms and a central pawl lock for securing the cable drum carrier to the chassis * Motor-hydraulic drum drive with oil motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft diameter 76 mm, with centering and rotating ends * 1 Pair of stepped Polyamide Centering Cones Isdpsu I Iqlefx Ab Usbf * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) * Finish: Hot-dip galvanized * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 5.840 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2025, * KWH 8.8 ML: * TPMS (Tire Pressure Monitoring System) * EBS braking system * Drum brake * BPW axle * Parabolic springs * Front support winch * Rear spring-assisted square tube supports with base plate, safety locking pins for variable support heights * Drawbar with 40 mm bolt coupling (height-adjustable in mm) * 15-pin electrical connector * LED lighting Ibedpfxsu I Iq Eo Ab Uof * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and cross members * Closed steel mudguards with splash protection * Closed lateral underrun protection, suitable for use as advertising space * Plastic toolbox with base insert (horizontal installation) approx. 500 x 350 x 400 mm * Swiveling cable drum mount, light width between drum arms 1,700 mm - with tension lock for drum securing at the ends of the support arms and a center-mounted claw lock for securing the cable drum mount to the chassis * Motor-hydraulic drum drive with oil motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft with 76 mm diameter, including centering and rotatable ends * 1 pair of stepped polyamide centering cones * Hydraulic power unit with diesel engine * Fuel tank and manual starter * 6.5 HP with gear pump (150 bar) * Surface hot-dip galvanized * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 13.700 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA 18.0: * 2-in-1 design: suitable for hooklift containers and use as a low loader * TPMS (Tire Pressure Monitoring System) * EBS electronic braking system * Emergency release mechanism for spring-loaded brake cylinders * Drum brakes * 2 x 10-tonne axles * Air suspension with manual lowering at the rear * Drawbar 2,000 mm long with 40 mm eye and height adjustment device * Tool box made of powder-coated sheet steel approx. 1,000 x 300 x 600 mm, plus a side-mounted spare wheel holder (basket design, right side) * Reflective contour tape on sides and rear * Side underrun protection * Plastic quarter mudguards with splash protection * Rear plastic bumper guards * Foldable 'A' sign at the rear * LED tail lights * 15-pin power connector * Main frame with raised outer rails to guide roll-off containers * Steel floor plates with roller recesses in the bogie area * Container length adjustable from 5,500 to 7,000 mm * Pneumatic 4-point container clamp locking and mechanical, insertable end stops at the front of the track; load securing certificate according to DIN 30722-1 * Load securing package consisting of: 1 pair of 10t UVV lashing rings at the front bulkhead, 3 pairs of 10t UVV lashing rings in the outer frame, 4 x 2t cloverleaf lashing eyes per side, and 4 x 8t recessed lashing shackles in the outer frame * Weld bead as an anti-slip coating in the approach ramp area Ibodjl Tq Nmjpfx Ab Uof * Mechanical drop-down support legs at the rear * 1 pair of aluminium drive-on ramps (10.6t/pair), dimensions: 2,800 x 470 mm, suitable for rubber-tyred and tracked vehicles (lockable rear storage compartment) * Chassis, bogie, locking components, and rear support legs hot-dip galvanized * Drawbar, axles, and air tanks painted in black * New vehicle without initial registration, with full manufacturer's warranty * Subject to errors and prior sale * Available from calendar week 05/2026

Stanje: novo, največja dovoljena obremenitev: 13.700 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA 18.0: * 2 in 1 – suitable for roll-off containers and as a low loader * TPMS (Tire Pressure Monitoring System) * EBS electronic braking system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 10 ton axles * Air suspension with manual lowering function at the rear * Drawbar 2,000 mm long with 40 mm towing eye and height adjustment * Tool box made of powder-coated steel sheet approx. 1,000 x 300 x 600 mm and spare wheel holder in basket design on the right side * Reflective contour tape on the sides and rear * Side underrun protection * Plastic quarter mudguards with splash guards * Plastic rear impact protection buffers * Foldable A-board at the rear * LED tail lights * 15-pin electrical connector * Main frame with raised outer frame for guiding roll-off containers * Steel floor with roller recesses in the bogie area * Container length from 5,500 to 7,000 mm possible * Pneumatic 4-point clamp locking as well as mechanical insertable end stops at the front in the guide rail, load securing certificate according to DIN 30722-1 * Load securing package consisting of: 1 pair of 10t UVV lashing rings at the front on the headboard carrier as well as 3 pairs of 10t UVV lashing rings on the sides in the outer frame, on each side 4 x 2t lashing eyes in cloverleaf design, as well as 4 x 8t lashing brackets recessed in the outer frame * Weld bead as anti-slip surface in the ramp track area * Mechanical drop-down supports at the rear Ibsdpfx Absl Tpc Ae Ujf * 1 pair of aluminium loading ramps (10.6t / pair) 2,800 x 470 mm suitable for rubber-tyred and tracked vehicles (lockable storage compartment accessible from the rear) * Chassis, bogie, locking parts, rear drop supports hot-dip galvanized * However, drawbar, axles, air tanks painted in black * New vehicle, unregistered, with full manufacturer’s warranty * Subject to prior sale and errors excepted * Available from calendar week 05 / 2026

Stanje: novo, največja dovoljena obremenitev: 12.260 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, Leto izdelave: 2026, * TM-TA 14.4: * Wabco EBS (electronic braking system) * RDÜ tire monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with equalizing unit * Jost support winch at the front, 2 external drop-down supports at the rear * Height-adjustable, hot-dip galvanized drawbar +/- 150 mm * Hot-dip galvanized chassis * 15-pin electrical connector * LED rear lights * Closed single plastic mudguards * Foldable A-board at the rear * Plastic underrun protection buffers * Hot-dip galvanized underrun protection with integrated chain storage box, dimensions: W= 370 mm x D= 420 mm x H= 480 mm, front left & right * 2 repositionable skip stops for lateral centering of skips * Skip stops at the front can be inserted in 4 positions with oscillating stop * 2 x 5.3 t UVV lashing rings per side for attaching tie-down equipment * Axles, springs, air tanks and support winch painted in black * Subject to errors and prior sale Ibsdpfxjl Thyqj Ab Ujf * New vehicle with manufacturer's warranty * Available from calendar week 05 / 2026

Stanje: novo, največja dovoljena obremenitev: 12.260 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, Leto izdelave: 2026, * TM-TA 14.4: * Includes 2 ratchet tensioners permanently mounted on the outer frame with chain box * Both sides fitted with eye and quick-shortener, Y-special version, 6.3 t * Tension force with load securing certificate * Wabco EBS * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring-loaded cylinders Iedpopk Dyxefx Ab Ujbf * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with compensating unit * Jost landing gear at the front * 2 x external drop-down supports at the rear * Height-adjustable +/- 150 mm hot-dip galvanized drawbar * Hot-dip galvanized chassis * 15-pin power connector * LED tail lights * Closed plastic single mudguards * Foldable A-board at the rear * Plastic impact protection buffers on the underrun guard * Hot-dip galvanized underrun protection with integrated chain stowage box, dimensions W=370 mm x D=420 mm x H=480 mm, front left & right * 2 re-positionable bin stops for lateral centering of bins * Front bin stops with pivoting stop, pluggable in 4 positions * Side-mounted, each with 2 x 5.3 t UVV lashing rings for attaching tensioning elements * Axles, springs, air tanks, and landing gear painted black * Subject to errors and prior sale * New vehicle with manufacturer's warranty * Available from week

Stanje: novo, največja dovoljena obremenitev: 10.360 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-ER 14.4: * RDÜ (Tire pressure monitoring with in-cab display via EBS signal, no installation required on truck side) * Electronic Braking System (EBS) * Emergency release device for spring actuators * Drum brakes * Gigant axles * Air suspension with lift and lowering function * Drawbar height-adjustable by approx. 300 mm * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding supports at the rear * Plastic toolbox front right, mounted externally on the front wall * Side underride guard * Plastic quarter mudguards * LED lighting system * 15-pin electrical connector * Hot-dip galvanized chassis, drawbar, front and rear walls * 50 mm softwood floor * Provision for retrofitting 20” container locks front and rear * Bolted front wall made from smooth sheet metal * Side walls made from trapezoidal-profile steel, folding, with tailboard spring lifter * Hot-dip galvanized, bolted rear stanchions * Perforated external frame, approx. 45° bent, with 2 t lashing capacity every 480 mm, optional installation of 3 t recessed lashing rings every 600 mm, front and rear corners each with 1x 6.3 t lashing point, various holes for 1.2 t lashing options in the front and rear crossmembers * 1 pair of aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 t / pair), suitable for rubber-tired and tracked vehicles, stowage compartment at the rear integrated under the loading platform in the chassis * Vehicle hot-dip galvanized * New vehicle with manufacturer’s warranty Ibodjndpn Sopfx Ab Uof * Errors and interim sale excepted * Immediately available ex Egestorf