Prikolica z nizko platformo

MÜLLER-MITTELTAL 19 to luftgef. Tandemtiefl. mit Einschubrampen

Stanje: novo, največja dovoljena obremenitev: 14.400 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * EC approval-TA-ER 19.0: * Wabco EBS-E (electronic braking system) * Tire Pressure Monitoring System (RDÜ) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 11 t Gigant axles * Air suspension with lifting and lowering system * Drawbar with 50 mm flanged towing eye and 110 mm height adjustment via offset plate * Jost landing gear at the front * Rear external folding supports * Plastic toolbox approx. 750 x 350 x 300 mm, mounted on right side * Side underrun protection * Plastic quarter mudguards * 15-pin electrical connector * Multi-chamber taillights * Reinforcement package for drilling rig transport on the chassis * 50 mm softwood plank floor, clamped design * Pre-fitting for retrofitting container locks in front of the bulkhead * Bolted bulkhead made of smooth sheet metal * Split side walls made of trapezoidal-profiled steel sheet, fold-down with central folding stanchion * Steel rear wall, can be inserted between the ramps – when not in use, stored at the front inside the bulkhead * Rear stanchions bolted * Perforated outer frame, approx. 45 degrees bent, with 2 t lashing capacity every 480 mm * Option to install 3 t drop lashing rings every 600 mm * Load securing package: in each front and rear corner 1 x 10 t UVV lashing ring, on each side 2 x 8 t UVV recessed lashing rings in the outer frame, various holes in the bulkhead and end cross member for 1.2 t lashing points * One-piece slide-in ramps approx. 2,750 x 620 mm * Rear drive-up slope approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, folding supports, and drive-up ramps hot-dip galvanized * ---Axles, air tanks, flanged towing eye, and landing gear painted black--- * Unladen loading height approx. 940 mm * Laden loading height approx. 910 mm * Wheelbase: 1,810 mm Itedpemi Tmaefx Ab Uor * Tires: 235/75 R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available from Egestorf

Stanje: novo, lastna masa: 6.600 kg, največja dovoljena obremenitev: 17.400 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 6.500 mm, skupna dolžina: 10.900 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R17,5 (Doppelbereifung), barva: srebrn, vrsta prenosa: mehanski, poraba goriva (mestna vožnja): 1.090 l/100 km, Unladen weight: 6,600 kg, permissible gross weight: 24,000 kg, cargo area length: 6,500 mm. Tyre size: 235/75 R17.5. 1st axle: , 2nd axle: , 3rd axle: . Leaf suspension. 3-axle low-bed trailer with drop-bed DTS-S 300 - Turntable with robust ball bearing ring - Rear supports, foldable - 1 spare wheel carrier for 1 spare wheel, incl. wheel mounting kit - 1 spare wheel, same brand and type as main tyres, steel rim - 1 plastic toolbox - Extendable load width up to 3,000 mm (not in rear slope) - Storage compartment for timber planks in the centre of the low-bed platform - Timber planks, 70 mm, for widening to 3,000 mm Tie-down points on low-bed: - with spring-loaded lifting aid Axles + suspension: - SAF - Drum brake axles - Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalisation (rocker compensation) Braking system: - Dual-line compressed air brake system - Spring-loaded parking brake Electrics: Ijdetcwkrspfx Ab Uetr - 24 Volt, multi-chamber lights, yellow LED side lights - 1 LED beacon with mounting bracket, controlled via parking light (removable beacon) - 2 pairs of warning boards, double LED illuminated, extendable to 3,000 mm Floor: - Storage box recessed into drive-up angle at the drop bed - Then 70 mm softwood floor, steel/chequer plate covering in wheel arch area - Rear slope with 70 mm softwood floor Ramps: Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable, covered with wood - 1 pair of ring lashing eyes recessed front in drop bed, 10 t - 4 pairs of lashing holes in rear area, 5 t each for tensioning strap hooks - 7 pairs of lashing points recessed top and side in outer frame, 10 t each (1 x front in drop bed, 6 x in low bed) - 5 pairs of stanchion pockets recessed in outer frame, inside 70 x 40 mm (convertible to 5 t ring lashing eyes for extra cost) - 2 additional pairs of folding lashing eyes, 10 t each, 1 x front in drop bed, 1 x behind 3rd axle Axles + suspension: - SAF - Drum brake axles - Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalisation

Stanje: rabljeno, lastna masa: 6.500 kg, največja dovoljena obremenitev: 23.500 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, prva registracija: 01/2008, naslednji pregled (TÜV): 03/2024, dolžina tovornega prostora: 8.000 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 910 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75R17.5, barva: oranžna, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Vehicle location: Bovenden, leaf suspension, 3 axles, BPW axles, turntable, ABS (anti-lock braking system), lashing eyes, hydraulic ramps, rear supports, side aluminum underrun protection, twin tires, storage box Iodpjqpgtmefx Ab Ujtr Body: Hydraulic ramps, extendable to 3m. BPW axles, drum brakes, lashing rings on the outer sides. Ramp length approx. 4000mm! ACCESSORY DETAILS WITHOUT GUARANTEE, subject to change, prior sale, and errors excepted!

Stanje: novo, številka stroja/vozila: 2dff0c136c85096f36822a0bb, lastna masa: 7.150 kg, največja dovoljena obremenitev: 16.850 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis - Low-bed Trailer Steel welded construction Turntable with heavy-duty slewing ring, storage box integrated into turntable front section Foldable rear supports 2 wheel chocks with holders Aluminium side underrun protection Full-width rear mudflaps Extendable extensions to 3,000 mm (not at the rear bevel) (Note: The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) Central storage compartment for timber boards on the loading platform 70 mm timber boards for extension to 3,000 mm Low-bed lashing rings 3 pairs of 10 t lashing points integrated into the front floor 6 pairs of 10 t lashing mushrooms recessed in the top and side of the outer frame 1 x by the neck area The remaining points are distributed at no more than 1200 mm intervals 1 x at the rear bevel 5 pairs of stake pockets recessed in the outer frame, internal dimensions 70 x 40 mm (can be converted to 5 t ring lashing eyes, not included) Drawbar Turntable Trailer Coupling Drawbar with certified 40 mm towing eye Axles & Suspension SAF drum-braked axles Axles/chassis laser-aligned to reduce tyre wear and fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bearings and mechanical Axle load equalisation (rocker balancing) Brake System 2-line compressed air brake system Coloured line routing for easy service Spring-loaded parking brake included 2 fail-safe coupling heads at the front, with connecting lines to the tractor unit ABS and ALB, with ABS plug at the front, with connecting cable Note: The trailer may only be towed by vehicles ensuring the proper function of ABS! Wheels and Tyres 235/75 R 17.5 Manufacturer’s choice Steel twin wheels, factory silver finish Electrics 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin fail-safe plugs at the front, with connecting cable 1 LED beacon with holder, switched via parking lights (removable beacon) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Steel floor in the front section, followed by 70 mm softwood flooring; wheel arch covers in steel/chequer plate Rear bevel with 70 mm softwood flooring Low-bed area incl. rear bevel 8,200 mm Access Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered, included With spring assist Operating Notes An exemption permit is required for 10,000 kg axle load—only indivisible loads allowed! The specified total weight is technically achievable, but depending on the load, the permissible total weight may not be reached due to axle/support/kingpin limits. (Poor driving and tracking may result from incorrect load distribution) Isdpfxji Riy Es Ab Ujtr Country of Registration/Plates Country of registration: Germany With Dekra inspection and appraisal (according to §13 EU-FGV) 24/7 service hotline Prepared for double-line license plate holder Contour marking with reflective stripes per ECE R 048, white to the side, red to the rear Paintwork Frame DB 7350 Novagrau 10-year guarantee against rust-through Drawbar galvanized or black, manufacturer's choice Access ramps hot-dip galvanized Note: Archive images!

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic brake system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles Isdpfx Abol Tphrs Ustr * Air suspension with lifting/lowering system and RtR valve * Smard-Board for load weight determination * Warning sign packages at the front & rear * Reflective contour tape on the sides and rear * Removable rear rotating beacon * LED lighting * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated sheet steel and spare wheel holder in basket design on right side * Front: closed single plastic mudguards * Rear: straight steel mud flaps with spray suppression * Side underrun protection * Turntable platform extended by 520 mm at the front, with 45° corners and 3 recessed, lockable storage compartments with lids * Chassis made of high-strength fine-grain steel * Decking over turntable platform made of 50 mm, and in low-bed platform of 60 mm coniferous timber * Outer planks of ramps made of hardwood * 4 stake pockets on each side (no stakes provided) with simultaneous 2 t lashing capability * Load securing package includes: 2 lashing eyes, 6.4 t, at the front left and right on the main frame of the turntable platform * On each side front and rear: 2 pairs of 13.4 t lashing rings on the outer frame and on each side 4 pairs of swiveling and lowerable 10 t lashing rings * Loadable in all directions, recessed into the outer frame * 2 pairs of 6.4 t lashing rings on the side in excavator arm recess * 8 pairs of galvanized folding outriggers for 3 m total width (not at the rear slope) * Widening planks stored in a side compartment on the left * Excavator arm recess over the rear axle to end of rear slope approx. 2,100 x 740 x 190 mm * Mechanical drop supports at rear * Hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm including hydraulic sideways ramp adjustment & load-holding valve * Loading deck over turntable: approx. 2,990 x 2,520 mm * Rear loading deck: approx. 6,780 x 2,520 mm * Load height loaded approx. 890 mm, +/- 20 mm (including 860 mm rear slope) * Flow divider installed * Chassis, turntable, loading ramps, folding outriggers, and mechanical drop supports hot-dip galvanized * Axles, drawbar, air reservoirs, and turntable painted in black * Tires: 235/75 R 17.5 * New vehicle, not previously registered, with manufacturer’s warranty * Errors and prior sale reserved * Available from CW 07/2026