Faymonville Delovna Platforma nakup rabljenega (205)

Stanje: novo, lastna masa: 15.550 kg, največja dovoljena obremenitev: 47.450 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimization of loading platform length, length approx. 3,700 mm - Rear gooseneck with bevel approx. 1,000 mm x 10° Loading Platform: - Extendable loading platform, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° - A recess in the loading platform as well as into the bevel for accommodating the excavator dipper stick - Pneumatic locking with conical locking bolts and reinforced lock positions - Hardwood covering on the loading platform bevel Ramps: - 1 pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm - Ramps with hardwood covering - Hydraulically folding ramp tips - Ramps can be hydraulically shifted individually approx. 235 mm outward and approx. 215 mm inward - Square climbing cleats 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, 1st axle lift-steered, all other axles forced-steered with hydromechanical system - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with raising and lowering valve - Tyres 235/75 R 17.5, twin tires - TPMS tire monitoring system compliant with ECE R141 - TPMS sensors installed in all wheels including spares Accessories included: - Removable steel front wall, approx. 400 mm high - 3kW electro-hydraulic power pack for hydraulic operations, excluding hydraulic winches - Parking position on gooseneck for warning boards when not in use - 1 spare wheel - On the gooseneck: 1 pair of removable side aluminium drop sides, approx. 400 mm high, anodised - On the gooseneck: 1 removable rear aluminium drop side, approx. 400 mm high, anodised - Above the gooseneck: approx. 40 mm thick hardwood floor, chequer plate above king pin - 2" king pin - Guide plate on gooseneck for fifth wheel, approx. 500 mm wide - 4 wheel chocks - Mechanical landing gear with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg Lsdpsk Aht Uofx Aa Rjhc - 1 intermediate table, approx. 300 mm wide - Extensions (galvanised) extendable by approx. 230 mm per side - Wheel recesses with square climbing cleats - ALU covers for the wheel recesses - 1 pair of mechanical rear supports - Remote steering at front and rear via cable remote control, with single track monitoring of axles - 1st axle with automatic lift axle function - Central lubrication system with 1 BEKAMAX brand pump - Radio remote control for remote steering, additionally to cable remote, with 2 indicator lights on the receiver as single track monitoring - Wabco Smart Board System - 4 warning boards, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for revolving beacon

Stanje: novo, lastna masa: 10.700 kg, največja dovoljena obremenitev: 38.800 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17,5, barva: sivo-črna, Oprema: ABS, Gooseneck: • Gooseneck with front corners beveled at 45° and rear taper approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Extendable loading platform: • Loading platform in extendable design with rear taper approx. 1,000 mm x 8° • Cut-outs in outer frame of loading platform for attaching tensioning straps • Approx. 48 mm thick hardwood flooring; anti-slip checker plate covering above the axles Two-piece steel ramps: • One pair of galvanized, two-piece steel ramps with approx. 48 mm thick hardwood covering • Ramps with hydraulically foldable ramp sections, hydraulic lift system, and hydraulically adjustable • Maximum load per pair: approx. 40,000 kg Axles and tires: • BPW axles and suspension, 2 rigid axles, 1 self-steering axle • Technical axle load: 12,000 kg Lsdpfjhlz S Nox Aa Rjhc • Electromagnetic reverse lock, activated via reverse gear or manually • Air suspension with lift and lower valve • Axle tools • 235/75 R 17.5 3PMSF Braking system: • WABCO braking system according to EU regulations with EBS-E Paintwork: • First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component zinc dust primer • High-quality, single-color top coat in MB 7350 Novagrey applied with two-component paint • Rear section metallized and painted in RAL 9010 Landing legs: • JOST landing legs with 2-speed gearbox for 24t lifting load (50t test load) Steel construction: • Steel construction made of high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC • S690QL/S700MC Electrical system: • Electrical system in accordance with EU regulations, 24 Volt lighting • ASPÖCK-UNIBOX on front connection panel with 24N, 24S & 15-pin sockets Accessories included: • One spare wheel with holder • Galvanized steel front wall approx. 400 mm high • Yellow-red air couplings on the galvanized front connection panel • 4 wheel chocks • Rear mounting bracket for beacon light at the end of the semitrailer • Recess at rear of gooseneck for ALU approach ramps • Galvanized folding supports under the loading platform taper • Cover plates to bridge the gap between ramps and loading platform • White reflector tape per EU regulations on sides, extension, and red at rear • Electro-hydraulic unit at rear, under the loading platform • On gooseneck and ramps, left and right, each with a holder for warning signs, including socket • Operating valves for the ramps located on the right side of the trailer • ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) • Four warning panels extendable by approx. 400 mm with a position light • 3 pairs of WADER container pockets in the loading platform for one 20ft, 30ft or 40ft container • 6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading platform • Galvanized extensions, extendable by approx. 230 mm per side • 20 x 20 mm square climbing strips every 200 mm on the outer frame of the platform taper • Painted anti-slip sand layer on checker plates, above king pin and loading platform • Load gauge for axle load measurement, including load diagram • HRM metallization (High Resistance Metallisation) of the outer frame • Complete steel construction shot-blasted, then defined visible surfaces metallized and hot-finished with ZINACOR 850 (Zinc 85% - Alu 15%)

Stanje: novo, lastna masa: 10.900 kg, največja dovoljena obremenitev: 37.100 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 890 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, obratovalna teža: 10.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the loading platform length, approx. 3,700 mm long, rear bevel approx. 1,000 mm x 6° - Technical king pin load: 18,000 kg - For tractor units: 4 x 2 and 6 x 2 Loading platform: - Loading platform, approx. 9,600 mm long with rear taper approx. 900 mm x 6° - Platform area behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, with a load capacity of up to approx. 9,000 kg - Grating surface and steel sheet floor approx. 5 mm thick as additional reinforcement on the sloped section of the platform Ramps: - One pair of two-section AXS steel ramps, approx. 4,675 mm long and approx. 900 mm wide - Grating surface - Hydraulically folding ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 365 mm inward - Painted sand coating on the outer frame and ramp tips Lhjdouadk Nspfx Aa Roc - Flashing lights on the outer sides of the ramp tips with control switch next to the ramp operation panel - Ramp lock in transport position with quick-release fastener Axles, suspension and tires: - BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steerable (trailing) - 1st axle with traction assistance - Operated via brake pedal in the tractor unit - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 - TPMS tire pressure sensors installed on all wheels including spare wheels Brake system: - WABCO EBS-E braking system in accordance with EU regulations Paintwork: - Trailer MB 7350 Novagrau Equipment included: - Removable front steel wall, approx. 400 mm high - 3 kW electro-hydraulic power unit for hydraulic operations, except for hydraulic winches - Gooseneck guide plate for the fifth wheel, approx. 500 mm wide - JOST Module B – static test load = 50,000 kg - Continuous grating with 5 mm steel underlay as additional reinforcement - Painted sand coating - Cutouts in the outer frame of loading platform and lift bed for hooking hydraulic ramp control valves on the right-hand side of the vehicle - 2" king pin - Central lubrication system with 1 pump, brand BEKAMAX - 1 pair of plug-in ALU side boards on the gooseneck, approx. 400 mm high, anodised - Electric winch, approx. 5,400 kg pulling force, with radio remote control - Steel wire rope approx. 24 m long, rope diameter approx. 9.5 mm, including rope pressure roller - WABCO Smart Board system - 4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, lastna masa: 29.600 kg, največja dovoljena obremenitev: 72.400 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 6.650 mm, širina tovornega prostora: 2.840 mm, višina nakladalnega prostora: 550 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, obratovalna teža: 29.600 kg, Oprema: ABS, Gooseneck: - Gooseneck hydraulically liftable/lowerable and detachable - Length approx. 3,650 mm - For tractor units: 6 x 4 or 8 x 4 2-axle front bogie: - Hook mountings at front and rear - Bogie length x width approx. 2,200 mm x 2,850 mm Excavator deck "BB-A": - Telescopic excavator deck "BB-A" with drive-over bridge hooks at the front and pin-lug coupling at the rear - Length x base width approx. 6,650 mm x 2,850 mm - Beam height x beam width approx. 400 mm x 1,350 mm - Loading height 550 mm with 150 mm ground clearance 4-axle rear bogie: - Mechanical pin-lug coupling for the installation of a lowbed at the front, rear crossmember at the back - Bogie length x width approx. 5,480 mm x 2,850 mm - Multiple lashing points Pendulum axles and tyres (front and rear bogies): - "PENDULUM AXLE", all axles forced-steered via hydromechanics - Hose rupture valve on axle compensation cylinders with automatic RESET function - Hydraulic cylinders with shut-off valves and locking clips for securing in raised position - Final coating on axles: 2 layers of single-colour MB 7350 Novagrau 2K paint - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres size 285/70 R19.5 Remote steering (after-steering): - Remote steering operable from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Socket for remote steering control on gooseneck - Cable remote control with pushbuttons and single-track control included Accessories included: - Yellow and red air couplings on the galvanised front connection bar - Steel front wall approx. 400 mm high - 4 wheel chocks - 3.5" king pin - One 7-pin socket left and right at rear of gooseneck for warning boards - Hoisting jib with winch for spare wheel at the front face of the gooseneck - Truck hydraulic connection with flow control (40 l/min), including support jib for supply lines; tractor unit tank must have at least 80 litres capacity with couplings - Plug-in ALU side and rear boards on gooseneck, approx. 400 mm high, anodised - Control lever on gooseneck protected by foldable cover - Separate air connection with air gun on gooseneck - BEKAMAX central lubrication system: 1x on gooseneck, 1x on 2-axle and 1x on 4-axle bogie - Variomax tool kit - Multi-coupling hydraulic connectors on gooseneck and at lowbed hook interface - 2 spare wheels - One 7-pin socket left and right, at front and rear of rear bogie for warning boards - Front bogie with separate air connection for impact wrench - Foldable steel bed extensions, adjustable in width from approx. 2,850 mm to 3,250 mm - Steel bed inserts can be placed in 2 positions for sunken load area - Steel mats with rubber flooring, approx. 12 mm thick - Thread-in options (⌀ 40 mm) every approx. 500 mm on the upper flange of the excavator deck outer tube for eye bolts Ljdpfxswcmhas Aa Rshc - One locking point at every approx. 500 mm on extension with mechanical lock - Socket on rear bogie for remote steering cable control - 2 reversing lights on rear panel - Four extendable warning boards (by approx. 2,000 mm), each approx. 423 x 423 mm with position lights - 1 work light left + right on rear panel of gooseneck with separate on/off switches - Two INOX toolboxes, approx. 855 x 340 x 390 mm - 1-cylinder Hatz diesel engine (Silent Pack) - Radio remote control for after-steering

Stanje: novo, lastna masa: 10.300 kg, največja dovoljena obremenitev: 39.200 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Platform: - Loading platform after the gooseneck, hydraulically liftable and lowerable, length approx. 2,800 mm, with rear chamfer approx. 1,000 mm x 8° - Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, over the axles with chequer plate covering Two-part Steel Ramps: - One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp parts, hydraulic lifting system, and hydraulically adjustable - Maximum load per pair: 40,000 kg Axles, Suspension and Tires: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated by reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tires 235/75 R 17.5 3PMSF - TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories Included: - One spare wheel with holder in front of the bulkhead - 2" kingpin - One galvanized steel front wall approx. 400 mm high - Yellow-red air couplings at the galvanized connection strip in front - 4 wheel chocks - Galvanized folding supports under the platform's rear chamfer - A holder for a rotating beacon at the rear of the trailer - Cover plates to bridge the gap between ramps and platform - White reflective tape as per EU regulations along the sides of the trailer and red at the rear - Electro-hydraulic unit at the rear, under the platform - At the gooseneck and at the ramps left and right, each with a holder for warning signs, including socket - Control valves for the ramps positioned on the right side of the trailer - European reflective plates (red-yellow) at the rear of the trailer - Manual and description on USB stick - Removable ALU side walls and rear wall on the gooseneck approx. 2,440 x 400 mm - The rear, galvanized side stakes are removable (body length approx. 2,560 mm) - An electric cable winch with radio remote control, approx. 5,400 kg lifting force, including 9.5 mm steel cable, 24 m long, with guide roller - Bolted 5 t ring for cable deflection of the winch on the gooseneck without pulley Lsdju Hp Hrjpfx Aa Rohc - 2 pairs WADER container pockets in the platform for a 20ft container - 6 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the platform - Lift axle on the front axle with control via TEBS E, depending on actual axle load and loading condition - 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN) - 1 pair of recessed lashing rings along the central beam at the rear chamfer (LC 10,000 daN) - Sand coating for slip resistance painted on the chequer plates on the gooseneck and on the platform - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and removable pump protection - Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm - Speed stickers 80 km/h rear and on both sides - Load manometer for determining axle loads including load chart - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then all defined visible surfaces metallized and hot-coated with ZINACOR 850 (zinc 85% - alu 15%)

Stanje: novo, lastna masa: 13.500 kg, največja dovoljena obremenitev: 51.500 kg, skupna masa: 69.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimizing loading platform length, length approx. 3,700 mm Gooseneck rear with chamfering approx. 1,000 mm x 10° Loading Platform: Telescopic loading platform, length approx. 8,800 mm, with rear chamfering approx. 500 mm x 10° Recess in the chamfer as well as into the loading platform to accommodate the excavator dipper stick Pneumatic locking with conical pin and reinforced locking positions Supply lines routed protected within the extendable beam, adapting to the respective platform length Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps individually adjustable hydraulically approx. 235 mm to the outside and approx. 215 mm to the inside Axles and Suspension: BPW axles and suspension, two rigid axles, two steering trailing axles Electromagnetic reverse lock, activated via reverse gear and manually Air suspension with lift and lower valve Lhjdpfxok Ahuge Aa Rjc Axle tool Tyres: 235/75 R17.5 3PMSF twin tyres Load index: 143/141J (144/144F) Brake System: WABCO braking system, EBS-E in accordance with EU regulations Lighting System: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Metalizing: Standard HRM metallization of the outer frame Complete steel structure shot-blasted, then visible defined surfaces metallized with ZINACOR 850 (Zinc 85% - Alu 15%) hot-refined Steel Construction: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified as per DIN-EN 287-1 MAG welding process according to EN ISO 4063 Shielding gas M21 as per EN ISO 14175 Accessories Included: Front wall made of steel, plug-in, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin 24N connection per ISO-11852, 24S connection per ISO-3731, 15-pin connection per ISO-12098 Round NATO socket on the front connection strip Cable to supply electro-hydraulic unit and/or electric winch (35 mm², 3.5 m long) between trailer and tractor with connector (NATO-NATO) 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches 1 spare wheel with mounting adapter Outer beam of the gooseneck with fastening holes for screwable lashing rings. The first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included One fastening hole in the rear upper area of the gooseneck's outer beam for a screwable lashing ring 1 pair of screw-in lashing rings Approx. 40 mm thick hardwood covering above the gooseneck On the gooseneck, 1 pair of plug-in side aluminium walls, approx. 400 mm high, anodized On the gooseneck, a plug-in aluminium rear wall, approx. 400 mm high, anodized 2" kingpin Gooseneck guide plate for fifth wheel, approx. 500 mm wide 4 wheel chocks with holder Holder for aluminium approach ramps Mechanical landing gear with 2-speed gearbox and crank Continuous hardwood floor approx. 50 mm thick on the loading platform, interrupted between axles Platform locking with conically welded locking profiles every 250 mm incl. tension plate Slotted holes at the front of the loading platform for attachable and adjustable bridging elements 1 intermediate table with recessed platform, approx. 300 mm wide for the draw-out tube with large cross-section, with sheet metal covering Front and rear with slotted holes

Stanje: novo, lastna masa: 14.800 kg, največja dovoljena obremenitev: 61.700 kg, skupna masa: 76.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck with rear chamfer of approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Loading Platform: • Extendable loading platform with rear chamfer of approx. 500 mm x 8° • 9 pairs of folding external lashing rings • 1 pair of recessed lashing rings at the front of the loading platform • Cutouts in the outer frame of the loading platform for attaching tension belts • Approx. 48 mm thick hardwood flooring, checker plate above the axles Landing Legs: • JOST mechanically operated landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: • BPW axles and suspension, 1st axle steering, 2nd and 3rd axle fixed, 4th and 5th axle follow-steering • Technical axle load: 12,000 kg • 1st, 4th, and 5th axles with electromagnetic reverse lock, activated via reverse gear or manually • Tyres: 235/75 R 17.5 3PMSF Brake System: • WABCO brake system in accordance with EU regulations including EBS-E (4S3M) Paintwork: • Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer • High-quality single-color two-component (2K) topcoat in MB 7350 Novagrau • Rear section metallized and painted in RAL 9010 (Pure White) Lhodoma Hf Rspfx Aa Rec Steel Construction: • Steel structure made from high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC (yield strength 355MPa) • S690QL/S700MC (yield strength 690MPa) Accessories: • One spare wheel with holder in front of the front wall • 2" king pin • Galvanized steel front wall, approx. 400 mm high • Front galvanized connection strip with yellow-red air couplings • 2 wheel chocks with holders mounted on the front wall • Rear mount on gooseneck for ALU drive-on ramps • Galvanized extendable wideners appx. 230 mm per side • Bracket for a beacon at the rear of the trailer • Galvanized supports under the chamfer of the loading platform • White reflector tape on the sides as per EU regulations, red at the extension and rear • Mounts for warning panels including socket left and right at the gooseneck and rear panel • Detachable ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • Rear galvanized plug-in stanchions removable (body length approx. 2,560 mm) • 3 pairs of WADER container pockets in the loading platform for a 20ft (30ft) or a 40ft container • 7 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform • Lifting axle on the front axle with TEBS E control according to the current axle load and loading condition • Movable mounting rails for ALU drive-on ramps at the rear of the vehicle • 20 x 20 mm square climbing strips at 200 mm intervals on the outer frame chamfer of the loading platform • BEKAMAX (Pico) centralized lubrication system with NLGI-2 standard grease and removable pump cover • Four extendable warning panels approx. 423 x 423 mm with a position light, extendable by approx. 400 mm • Holder for beacon mounted on the warning panels • European reflector plates (red-yellow) on the rear of the trailer • 80 km/h speed limit stickers at rear and both sides • Axle load gauge with load diagram included • HRM Metallisation (High Resistance Metallisation) of the outer frame • Complete steel structure is shot-blasted, then defined visible surfaces are metallized with ZINACOR 850 (zinc 85% - aluminum 15%) using hot finishing

Stanje: novo, lastna masa: 10.350 kg, največja dovoljena obremenitev: 39.150 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Loading area: - Telescopic loading area with rear chamfer approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm - Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom - Between the 1st and 2nd axle, 1 pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm - 3-piece detachable galvanized covers over the wheel recesses (W 670 mm) – max. point load 5 t / pc. - Recess in the chamfer and protruding into the loading area for the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of foldable external lashing rings (LC 5,000 daN) - 2 pairs of foldable external lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) - Cutouts in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) One-piece aluminum ramps: - 1 pair one-piece ALU ramps, approx. 2,500 x 600 mm - Ramp with spring lifting mechanism and manually adjustable - Maximum load per pair: 24,000 kg Axles and tires: - BPW axles and suspension, 2 rigid axles, 1 trailing steering axle - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tyres 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 Accessories included: - 1 spare wheel with holder in front of the bulkhead - 2" kingpin - 1 galvanized steel front wall approx. 400 mm high - At the galvanized coupling rail at the front, yellow-red air couplings - 4 wheel chocks with holder at the bulkhead - Mounting point at the rear of the gooseneck for ALU ramps - Galvanized extensions, extendable by approx. 230 mm per side - Galvanized folding supports under the chamfer of the loading area - 1 holder for a rotating beacon at the rear of the trailer - White reflective tape laterally, at the extension, and red at the rear, per EU regulations - At the gooseneck and rear panel, left and right, each with a holder for warning signs including socket - On the gooseneck, plug-in ALU sideboards and rear wall, approx. 2,440 x 400 mm - The rear galvanized stakes are removable (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container Ledpfsiu Er Aox Aa Rshc - 3 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area - 1 removable galvanized intermediate table with 1 pair of WADER container pockets - 20 x 20 mm square climbing strips every 200 mm on the outer frame in the chamfer of the loading area - Anti-slip sand coating on the checker plates on the gooseneck and the loading area - Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with position light - Holder for rotating beacon on the warning signs - 80 km/h speed stickers at the rear and on both sides - Load gauge for determining axle loads including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then all defined visible surfaces metalized and hot-finished with ZINACOR 850 (Zinc 85% – Alu 15%)

Stanje: novo, lastna masa: 34.500 kg, največja dovoljena obremenitev: 106.700 kg, skupna masa: 141.200 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.150 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 580 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, obratovalna teža: 34.500 kg, Oprema: ABS, Gooseneck: - Gooseneck hydraulically lift/lowerable as well as detachable - Length approx. 3,650 mm - Extensive lashing positions - For tractor units: 6 x 4 or 8 x 4 Ledpfxjwhywfj Aa Rjhc 3-Axle Compact Front Bogie: - Hook mounts at front and rear - Chassis length x chassis width approx. 3,560 mm x 2,850 mm - Extensive lashing positions Excavator Deck “BB-A”: - Telescopic excavator deck “BB-A” with drive-over deck hooks at the front and bolted lug coupling at the rear - Length x base width approx. 7,150 mm x 2,850 mm - Beam height x beam width approx. 430 mm x 1,350 mm - Loading height 580 mm with 150 mm ground clearance - 5 pairs of hanging lashing rings (LC 10,600 daN) - 4 pairs of threaded blocks M30 on inner beam for mounting screw-on rings 5-Axle Rear Bogie: - Mechanical bolt-on lug coupling for fitting a lowbed front, rear end traverse - Chassis length x chassis width approx. 6,840 mm x 2,850 mm - Extensive lashing positions Pendulum Axle and Tyres (front and rear bogie): - “PENDEL-AXLE”, all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-plugs for securing in lifted position - Final paint of axles with 2 coats of 2K paint, single-colour in MB 7350 Novagrau - Technical axle load: 14,640 kg (62 km/h) - Hydraulic axle compensation - Axle tools - Tyres 285/70 R19.5 Steering Override: - Remote steering from the front and rear via cable remote control with push buttons, including axle tracking control - Socket for steering control operation on the gooseneck - Cable remote control with push buttons including axle tracking control Included accessories: - Yellow-red air couplings on galvanised front connection rail - Steel headboard approx. 400 mm high - 4 wheel chocks with holders - 2 spare wheels 285/70 R19.5 - 3.5" kingpin - Gantry with winch for spare wheel at the front side of the gooseneck - Truck hydraulic connection with flow control valve (40 l/min), including gantry for suspension of supply lines, tractor unit tank must be at least 80 litres with couplings - White reflective tape according to EU regulations on sides and extension, red at rear - Plug-in ALU side panels and rear wall on gooseneck, approx. 400 mm high, anodised - Operating lever on gooseneck protected by folding cover - Separate air connection with air pistol on gooseneck - Central lubrication system BEKAMAX with standard grease NLGI-2: 1x on the gooseneck, 1x on 3-axle bogie, 1x on 5-axle bogie - Variomax tool kit - Multi-coupling hydraulic connections in the lowbed hook area - Front bogie with separate air connection for air screwdriver - Threaded inserts (ø 40 mm) every approx. 500 mm on outside of upper flange of excavator deck for screw rings - Folding extensions with steel mats, width adjustable from approx. 2,850 mm to approx. 3,250 mm - Steel mats with rubber covering approx. 12 mm thick - Two INOX toolboxes 855 x 340 x 390 mm - Radio remote control for steering override in addition to cable remote - Painted sand layer as anti-slip measure - 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery

Stanje: novo, lastna masa: 13.250 kg, največja dovoljena obremenitev: 47.550 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, vzmetenje: zrak, velikost pnevmatike: 245/70 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings 30 mm thick hardwood flooring Extendable loading platform: Loading platform in extendable design with rear chamfer approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings 3 pairs of outward-folding lashing rings Lhsdpfx Aael Uxdks Rjc 1 pair of flat lashing rings at the front of the loading area Cut-outs in the outer frame of the loading area for inserting tension straps Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Two-part steel ramps: One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering. Ramp with hydraulically folding and unfolding parts, hydraulic lifting system, and hydraulically adjustable position. Maximum load per pair: 40,000 kg Landing legs: JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced-steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool Tires 245/70 R 17.5 Braking system: Braking system according to EU regulations with EBS-E (4S3M) without connecting lines to tractor unit Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer High-quality one-color two-component (2K) top coat in Novagrau Rear section metallized and painted in RAL 9010 (pure white) Metallic paint not possible Electrical system: Electrical system according to EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connections conforming to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" kingpin One galvanized steel headboard approx. 400 mm high At the galvanized front connection strip, yellow-red air couplings 4 wheel chocks with holders at the headboard One spare wheel with holder in front of the headboard Electro-hydraulic power unit Rear and front remote steering via cable remote control with push-buttons, with single-track control of the axles Bracket at rear of gooseneck for ALU drive-on ramps European reflector signs (red-yellow) at trailer rear White reflective tape according to EU regulations at the sides, at the extension, and red at the rear At the gooseneck and on the ramps left and right, each with a holder for warning signs including socket One holder for beacon at trailer rear Galvanized folding supports under the loading platform chamfer Ramp operating valves fitted on the right side of the trailer Cover plates to bridge the gap between ramps and loading platform One mudflap at trailer rear Manual and description on USB stick Central lubrication system BEKAMAX (Pico) with general-purpose grease NLGI-2 and removable pump guard On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm The rear galvanized stakes are removable, superstructure length approx. 2,560 mm One INOX toolbox 1,350 x 400 x 400 on the gooseneck, box covers oil filler cap 4 pairs of WADER container pockets in the loading area for a

Stanje: novo, lastna masa: 17.250 kg, največja dovoljena obremenitev: 48.700 kg, skupna masa: 66.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 375 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 17.250 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize loading platform length, approximately 3,750 mm long - Gooseneck hydraulically liftable, lowerable, and detachable - For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Lowbed: - Lowbed with external beams, designed as a telescopic vessel bridge in low-profile construction with front extension - Length x width approx. 7,550 mm x 2,740 mm - Mechanical locking of the extension Chassis: - Rear chassis with closed outer frame - Checker plate surface and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, Suspension, and Tyres: - “PENDEL-AXLE”, all axles hydromechanically forced steered - Burst protection valve on the axle compensation cylinders with automatic reset function - Hydraulic cylinders with shut-off valves and plug pins for securing in raised position - Final coating of axles: two coats of single-color 2-component paint in "FAY-Grey-34-0260" - Technical axle load 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 Accessories: - Detachable steel front wall, approx. 400 mm high - 4 wheel chocks - Rear upper gooseneck area closed with removable cover - 1 pair of steel ramps with climbing bars and locking bolts to bridge the lowbed mounting hooks - Ramps can be positioned over or between the hooks - Mounting options for steel drive-on ramps at the rear, between the outer beams of the gooseneck - Locking point approx. every 1,000 mm on the extension - 1 lashing ring each, left and right, on the front cross member - Supply line connection strip for tractor unit, mounted at the height of outer frame profile - 6 pairs of threaded blocks on the exterior of the load floor inner beams for attaching M24 screw rings - 6 pairs of recessed lashing rings on the outside of the load floor outer beams, foldable inwards and outwards - 1 pair of threaded blocks on the front and rear of the load floor outer beams for M24 screw rings - Mounting rail for loose aluminum approach ramps on the end cross member of the vehicle - Central lubrication system with 2 pumps, brand BEKAMAX - Remote steering front and rear, cable remote controlled, with axle tracking control - 3 kW electro-hydraulic power unit for hydraulic operations, except hydraulic winches - Removable galvanized loading floor, can be placed in 3 elements between the outer beams, with hardwood covering - Foldable extensions, approx. 230 mm per side - Loose extension boards, steel-edged - 4 warning signs approx. 423 x 423 mm Lhjdpfoh Hm Tzox Aa Rec - Radio remote control for rear steering - 3.5” kingpin - Anti-slip coating on the left chamfer of the gooseneck - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Guide plate from gooseneck for the fifth wheel plate, approx. 800 mm wide - 1 spare wheel with mounting adapter - Parking position on the gooseneck for warning signs when not in use - 2 pairs of stake pockets integrated into the chassis outer frame, for plug-in stakes approx. 100 x 50 mm - Excavator stick trough of rear chassis closed at the rear with a removable plate - Trailer color: Mercedes-Benz 7350 Novagrey

Stanje: novo, največja dovoljena obremenitev: 49.000 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with front corners chamfered at 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Extendable Loading Platform: - Loading platform, extendable design with rear chamfer of approx. 1,000 mm x 8° - 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) - 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - 1 pair of horizontal lashing rings at the front of the loading platform (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for securing straps (LC 2,000 daN) - Hardwood flooring approx. 48 mm thick, checker-plate covering above the axles Two-Part Removable Ramps: - One pair of galvanized two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp sections, hydraulic lifting mechanism, and hydraulic side-shift - Maximum load per pair: 40,000 kg Lhjdpfjh Etf Rsx Aa Roc Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Axles and Tyres: - BPW axles, two fixed axles and two steering axles (self-steering), air suspended, with drum brakes, raise/lower function - Self-steering axles with electro-magnetic reverse lock, can be activated by reverse gear or manually - Axle tool kit - Tyre size 235/75 R 17.5 Brake System: - Braking system according to EU regulations with EBS-E (4S3M) Steel Structure: - Steel structure made of high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Paintwork: - First-class, long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component (2K) zinc dust primer - High-quality single-tone topcoat using 2-component (2K) paint in Nova grey Electrical System: - Electrical system according to EU regulations, 24 volt lighting, ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX on the front connector strip with 24N, 24S, and 15-pin sockets Included Accessories: - 2" kingpin - Galvanized steel front wall, approx. 400 mm high - One spare wheel with holder in front of the headboard - Yellow-red air couplings on the galvanized front connector strip - 4 wheel chocks with holders on the front wall - Mount at the rear section of the gooseneck for ALU approach ramps - Galvanized folding supports underneath the loading platform chamfer - One holder for warning beacon - Cover plates to bridge the gap between ramps and loading platform - White reflective tape on the side, red on extension and rear, according to EU regulations - Electro-hydraulic power unit - At the gooseneck and ramps (left/right) a holder each for warning signs including socket - Control valves for the ramps mounted on the right side of the trailer - One mud flap at the rear of the trailer - Manual and documentation on USB stick - On the gooseneck, plug-in ALU side boards and rear wall approx. 2,440 x 400 mm - Rear galvanized plug-in stakes are removable (body length approx. 2,560 mm) - 4 pairs of WADER container pockets in the loading platform for one 20ft, two 20ft or one 40ft container - 7 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading platform - Galvanized, extendable platform wideners approx. 230 mm per side - Lift axle on the front axle with control system - 20 x 20 mm square climbing bars - BEKAMAX central lubrication system - Four warning signs extendable by approx. 400 mm eac

Stanje: novo, lastna masa: 15.450 kg, največja dovoljena obremenitev: 65.550 kg, skupna masa: 80.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 21.900 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 925 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimized platform length, approx. 3,700 mm long, with rear tapering of approx. 1,000 mm x 10° Technical fifth wheel load: 30,000 kg. For tractors: 4x2, 6x2, and 6x4 Loading Platform: Double-extendable loading platform, approx. 8,800 mm long with rear taper of approx. 500 mm x 10°. A support table approx. 300 mm wide is welded to the central beam, featuring elongated slots at the front and rear for optional bridge elements that can be hooked in and repositioned Pneumatic locking with conical locking pin and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles and Tyres: BPW axles and suspension, first axle self-steering, all other axles hydraulically and mechanically forced-steered First axle equipped with an electro-magnetic reverse lockout, activated via reverse gear and manually. Technical axle load: 12,000 kg. Air suspension with lift and lower valve Manufacturer by our choice Sockets and Lighting: 24-volt lighting system in accordance with EU regulations ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Complete HRM metallizing Full steel construction, shot-blasted, then hot-finished with ZINACOR 850 Paintwork: 6-stage finishing process: Complete steel construction shot-blasted after welding 1 coat of zinc-based primer, 1 coat of adhesion primer. Final paintwork in 2 coats of 2K paint in single-tone DB 7350 Novagrau, followed by cavity sealing with special wax Accessories: Detachable front wall made of steel, approx. 400 mm high Connection strip for supply lines to the tractor unit, fitted at the height of the outer frame profile ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets. If your pin configuration deviates from the ISO connector standard, please inform us 3 kW electro-hydraulic power unit for hydraulic functions (excluding hydraulic winches) 1 pair of plug-in ALU sidewalls on the gooseneck, approx. 400 mm high, anodized finish 3.5'' king pin. Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide 2 wheel chocks with holder in front of the front wall Mechanical landing legs with 2-speed gearbox and crank Control valves for hydraulic ramps located on the right side of the vehicle 1 pair of mechanical rear supports Central lubrication system with 1 pump, BEKAMAX brand, using standard grease according to NLGI-2 Removable guard covering the pump(s) of the central lubrication system Remote steering from front and rear, controlled by cable remote with push buttons, with axle tracking control, no installation required on tractor unit Under the gooseneck and on the rear crossmember, one 7-pin socket with holder for warning signs each on left and right. One 7-pin socket on the rear crossmember Manual and documentation One-piece INOX stowage box, approx. 2,480 x 340 x 390 mm, straight design Lhedpfxjrigw Re Aa Rjc Please note that any special equipment and accessories will increase the unladen weight and correspondingly reduce the payload Warning package: 4 warning boards, approx. 423 x 423 mm, extendable by approx. 1,000 mm, incl. 2 LED position lights and brackets for beacon.

Stanje: novo, največja dovoljena obremenitev: 38.100 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.100 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5 3PMSF, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer of approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading platform: 5 pairs of fold-out lashing rings 3 pairs of fold-out lashing rings 1 pair of horizontal lashing rings at the front of the loading area Cut-outs in the outer frame of the loading surface for hooking in tension belts Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Landing legs: JOST landing legs with 2-speed gears for a 24 t lifting capacity Axles and tyres: BPW axles, two axles are fixed, two axles are self-steering, air-suspended, with drum brakes, with lift/lower function The self-steering axles come with an electro-magnetic reverse lock, which is activated via reverse gear or manually Ljdpfx Aajtphtmj Rjhc Axle toolkit Tyres: 205/65 R17.5 3PMSF Brake system: WABCO brake system according to EU regulations with EBS-E Steel construction: Steel structure made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Electrical equipment: Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK lighting ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component zinc dust primer High-quality single-colour 2-component top coat in MB 7350 Novagrau No metallic paint possible Rear section metallized and painted in RAL 9010 Accessories included: 1 spare wheel 205/65 R 17.5 TPMS tyre pressure monitoring system acc. to ECE R 141 At the galvanized front connection strip yellow-red air couplings 4 wheel chocks with holder on front wall Bracket at rear of gooseneck for ALU access ramps Galvanized folding supports under the chamfer of the loading surface Mount for a revolving beacon at the rear of the trailer Height-adjustable curtain structure Galvanized front wall with a tension mechanism for the sliding curtains Height-adjustable by approx. 400 mm "EDSCHA" brand roof, sliding forward on ALU roof beam profiles, bolted to the front and rear wall In the loading surface, 3 pairs of sliding stakes Superstructure at rear hydraulically extendable to left and right by approx. 750 mm Sliding roof with upward swinging portal carrier Sliding tarp with 700 mm reserve length, with tension straps at intervals of approx. 600 mm Height to top edge of superstructure approx. 3,960 mm Journeys with the sliding roof open are not permitted and will damage the tarp Mounting rail for ALU access ramps at the rear of the vehicle At the gooseneck and at the rear panel left and right, each with a mount for warning signs incl. socket A mud flap at the rear of the trailer European reflector plates at the rear of the trailer 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading area Lifting axle on the front axle controlled by TEBS E depending on current axle load and load status Rear structure with closed ALU double-wing doors A sanded, anti-slip paint layer on the checker plates on the gooseneck and on the loading surface BEKAMAX centralized lubrication system with standard grease NLGI-2 and a removable guard around the pump Speed stickers 80 km/h on rear and both sides Load manometer for axle load determination including load chart

Stanje: novo, lastna masa: 12.900 kg, največja dovoljena obremenitev: 34.100 kg, skupna masa: 47.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 350 mm, vzmetenje: drugo, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 12.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm in length - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2, and 6x4 Loading Platform: - Low-bed with external beams, extendable “SUPER LOW” design, approx. 6,850 mm in length - Low-bed with fixed hardwood flooring, approx. 40 mm thick, with mechanical locking device Rear Chassis: - Rear chassis with closed outer frame, chequer plate covering, and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings, foldable to the outside - 1 pair of lashing rings recessed in the trough - 2 pairs of stake pockets for insertable stakes 100 x 50 mm in the external frame Pendulum Axle and Tyres: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and safety locking pins for securing in raised position - Axles painted with two layers of single-colour 2K paint in “FAY-Grey-34-0260” - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 - TPMS tyre pressure monitoring system according to ECE R 141 Accessories: - Preparation for the installation of bolt-on container locators for 1 x 20ft or 1 x 40ft container on the outer girders - 2" king pin - One galvanized steel front wall, approx. 400 mm high - One spare wheel - Yellow-red air couplers on the galvanized front connection bar - 4 wheel chocks Lsdpfxehlz R So Aa Rehc - Remote steering from front and rear, operable via wired remote control with push buttons, with single-track alignment control - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of screw couplings - Electro-hydraulic power unit - White reflective tape in accordance with EU regulations on sides, extension, and rear - European reflective plates (red-yellow) on the rear of the trailer - One bracket on each side of gooseneck and rear plate for warning panels, including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on outer beam for mounting screw-on RUD Rings VLBG-4 - Detachable ALU side boards and rear board on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized insertable stakes are removable (body length approx. 2,560 mm) - Gooseneck rear upper area covered with removable cover - 5 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading area - Folding extensions, approx. 230 mm per side - 2 pairs of bolted RUD Rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the mounting hooks of the low-bed - Anti-skid sand layer painted on loading surface - 80 km/h speed stickers at rear and both sides - Spoon boom trough at rear chassis closed at rear with plug-in plate - Four extendable warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for rear axle steering in addition to cable remote, with indicator lights on receiver for alignment control - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard NLGI-2 grease - Load pressure gauge for determining axle loads - HRM Metallisation (High Resistance Metallisation) of outer frame - Complete steel structure shot blasted, then all defined visible areas metallized and finished with ZINACOR 850 (zinc 85% - aluminium 15%) hot galvanizing

Stanje: novo, največja dovoljena obremenitev: 36.500 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle stock, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Full specifications available upon request. * Gooseneck, approx. 4,100 mm long with central beam * Platform deck, extendable twice, approx. 9,400 mm in length * BPW axles and suspension * All axles hydro-mechanically forced steered * Technical axle load: 12,000 kg * Air suspension with lifting and lowering valve * Tires: 235/75 R 17.5 3PMSF dual mounted * WABCO brake system, EBS-E * 3 kW electro-hydraulic power unit for hydraulic operations, without installation of supply connections at the tractor unit * 4 pairs of stake pockets recessed into the outer frame of the gooseneck, for insertable stakes approx. 100 x 50 mm * 2-inch king pin * 8 pairs of stake pockets recessed into the outer frame of the platform deck, for insertable stakes approx. 100 x 50 mm Lhjdjwvzg Rspfx Aa Rsc * 1 lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the deck on the left in the direction of travel * Remote steering from the front and rear via cable remote control with push buttons; with single-track axle monitoring; no installation in the tractor unit * 2 axle load gauges mounted on the left side * Steel front wall, approx. 1,600 mm high * 3 transverse stake pocket strips in the platform deck, for insertable stakes approx. 100 x 50 mm * 1 transverse stake pocket strip in the gooseneck deck, for insertable stakes approx. 100 x 50 mm * 1 additional lockable INOX toolbox under the platform deck * WADER container pockets in the platform deck for transporting: 2x 20' containers or 1x 40' container * Central lubrication system with 2 pumps, brand BEKAMAX * Complete HRM metallization (High Resistance Metallisation)

Stanje: rabljeno, največja dovoljena obremenitev: 37.535 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 08/2024, naslednji pregled (TÜV): 08/2026, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt from the equipment list. Full equipment details available upon request. Loading Platform: * Extendable loading platform with pneumatically actuated locking mechanism * 7 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * Cutouts in the outer frame of the loading platform for attaching lashing straps (LC 2,000 daN) Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles, air-suspended, with disc brakes (approx. 430 mm), with lift/lower function. Technical axle load: 10,000 kg each (ET0) * Follow-up steering axle with electro-magnetic reverse lock, activated via reverse gear or manually * Axle tool Tyres: Lsdpfx Ajxgk U Nsa Rehc * Tyres 385/65 R 22.5 Braking System: * Braking system compliant with EU regulations with EBS-E (2S2M) without interconnecting lines to the tractor unit Steel Structure: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Paintwork: * Premium and long-lasting corrosion protection for the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer * High-quality 2-component (2K) single-colour top coat finish in RAL 3002 carmine red * Silver rims * Rear section metallised and painted in RAL 9010 (pure white) Including the following additional equipment: * Yellow-red air couplings at the galvanised front connection panel * 4 wheel chocks with holders * 2-inch kingpin * Yellow reflector tape according to EU regulations, at the sides, on the extension, and rear of trailer * European reflector plates (red-yellow) at the rear of the trailer * Loading platform equipped with approx. 30 mm thick wooden floor, enclosed in omega profiles * 10 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading area * Storage for up to 9 pairs of plug-in stakes approx. 100 x 50 mm, bolted to the inside of the front wall * 1 spare wheel holder under the loading platform, left side in the direction of travel, without spare wheel * 1 mudflap at the rear of the trailer * Manual and description on USB stick * One bracket for a warning beacon at the rear of the trailer * On the gooseneck and rear panel, each left and right, a bracket for warning boards including socket * 80 km/h speed label at rear and on both sides * Load manometer for axle load determination including load diagram * Galvanised steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container locks in the loading floor, for 1x 20' container, 2x 20' containers or 1x 40' container flush with the rear * Stainless steel toolbox, approx. 600 x 350 x 600 mm, under the loading platform, left side in direction of travel * 4 pairs of stake pocket rails mounted lengthwise on the loading platform, for plug-in stakes 80 x 50 mm * Lift axle on the front axle, controlled by TEBS E depending on current axle load and loading status * 2 LED reverse lights mounted on the rear panel * HRM metallisation (High Resistance Metallisation)

Stanje: rabljeno, največja dovoljena obremenitev: 38.080 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 02/2025, naslednji pregled (TÜV): 02/2026, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Complete equipment details available on request. Loading platform - Loading platform, extendable design with pneumatically operated locking - Loading area with approx. 30 mm thick wooden floor, enclosed in omega profiles - 7 pairs of fold-out lashing rings (LC 5,000 daN) - 3 pairs of fold-out lashing rings (LC 10,000 daN) - Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox, approx. 24 t lifting capacity (test load approx. 50 t) Axles - BPW axles and suspension - All axles hydro-mechanically forced-steered - With disc brakes - Technical axle load: 10,000 kg each (ET 0) - Air suspension with lift and lower valve - Axle tools Tyres - Tyres 385/65 R 22.5 Braking system - Braking system in accordance with EU regulations with EBS-E (2S2M) without connection lines to the tractor unit Warning signs - Bracket for warning plates on both the gooseneck and rear wall, including socket Electrical system - Electrical system in accordance with EU regulations - Lighting 24 Volt ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front terminal strip with 24N, 24S & 15-pin sockets, connection according to ISO 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Ledpfx Aexf Sifoa Rjhc Steel construction - Steel construction made from high-strength fine-grained steels - Steel grades S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork - First-class and durable corrosion protection of the standard shot-blasted welded frame ensured by a 2-component (2K) zinc dust primer - High-quality single-color 2-component (2K) topcoat in RAL 3002 Carmine Red - Wheels in silver; add-on parts per manufacturer’s specification - Rear section metallized and painted in RAL 9010 (pure white) Included accessories - 2-inch king pin - 4 wheel chocks with bracket on the bulkhead - Remote-controlled steering front and rear via cable remote, with axle single-track monitoring (no installation in tractor unit required) - Manual and documentation on USB stick - Electro-hydraulic power pack - Yellow-red air couplings on galvanized front terminal strip - Yellow reflective tape to EU regulation on sides, extension and rear of trailer - European reflective marking boards (red-yellow) on trailer rear - One mudflap at trailer rear - Bracket for beacon at trailer rear - 10 pairs of stake pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform - 1 spare wheel carrier under platform, right side in driving direction - Speed sticker 80 km/h on rear and both sides - Load gauge for axle load determination including load chart - Galvanized steel bulkhead (EN12642-XL), approx. 1,600 mm high - 6 pairs of WADER container pockets in loading platform for 1 x 20', 2 x 20', or 1 x 40' container; for the extension, an additional locking position for a 45' container - 4 pairs of transverse stake pocket rails in the loading area for approx. 100 x 50 mm plug-in stanchions - Storage for removable stanchions inside bulkhead - Access ladder mounted left and right in driving direction - One INOX toolbox, approx. 1,200 x 460 x 550 mm, front left under platform - An additional tool ...

Stanje: novo, največja dovoljena obremenitev: 73.090 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, You will find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Below is an excerpt from the equipment list. Full specification available on request. Gooseneck: * Gooseneck hydraulically liftable/lowerable and detachable * Length approx. 3,650 mm. Suitable for tractor units: 6x4 or 8x4 2-axle compact front bogie: * Hook mounts at front and rear. Length: approx. 2,200 mm * Chassis width: approx. 2,850 mm Lowbed: * ATX-A lowbed with telescopic longitudinal beams in low-profile design, with fixed hardwood flooring, approx. 50 mm thick * Drive-over bridge hooks at the front and bolt/lug coupling at the rear * Base width: approx. 2,850 mm * Length: approx. 7,150 mm * Beam height: approx. 300 mm * Beam width: approx. 650 mm * Loading height approx. 450 mm with ground clearance of approx. 150 mm 4-axle rear bogie: * Mechanical pin/lug coupling for attaching a lowbed at the front * End crossmember at the rear * Chassis width: approx. 2,850 mm * Chassis length: approx. 5,480 mm 2-axle front bogie: * Pendulum axles, all axles hydro-mechanically steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and pre-locking pins for securing in raised position * Final painting of axles with two layers of 2K paint, single color in MB7350 Novagrau * Technical axle load: approx. 14,640 kg (62 km/h) * Hydraulic axle compensation 4-axle rear bogie: * Pendulum axles, all axles hydro-mechanically steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and pre-locking pins for securing in raised position * Final painting of axles with two layers of 2K paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg (62 km/h) * Hydraulic axle compensation Tyres: * Tyres as per manufacturer's choice (M+S) 285/70 R19.5 * Load index 150/148J Paintwork: * Entire steel structure automatically shot-blasted after welding process * Second abrasive blasting with corundum for optimal adhesion of the coating system * HRM metallization of the entire chassis with ZINACOR 850 (85% zinc/15% aluminum) * Final coating with 2 layers of 2K top coat, single color in RAL 3002 Carmine Red according to RAL system 841GL Including the following accessories: * Steel front wall, approx. 400 mm high * Removable ALU side and rear walls for gooseneck, approx. 400 mm high * 3.5 inch king pin * Truck hydraulics connection with flow regulator (20 l/min), including gallows for hose suspension * Tank on tractor unit (SZM) must be at least 80 liters * With MAX Trailer coupling units, otherwise couplings to be supplied free issue by customer * BEKA-MAX central lubrication for one gooseneck with standard grease NLGI-2 * Multi-coupling hydraulic connectors on gooseneck * Front bogie with separate air connection for pneumatic screwdrivers * BEKA-MAX central lubrication for one 2-axle bogie with standard grease NLGI-2 * Preparation for mounting bolt-on container positions for 1 x 20' or 1 x 30' on the outer beams Lodexbv Auopfx Aa Rjhc * Without container locks * Mounting points on the outer beams of the loading platform for foldable extensions * BEKA-MAX central lubrication for one 4-axle bogie with standard grease NLGI-2 * Socket on rear bogie for connection of cable remote control for trailing steering * Rear bogie with trough * One LED beacon with bracket left and right on the rear crossmember

Stanje: novo, lastna masa: 17.500 kg, največja dovoljena obremenitev: 43.500 kg, skupna masa: 61.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.750 mm, višina nakladalnega prostora: 400 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - For tractor units: 6x4 or 8x4 Lowbed: - Lowbed with external beams, extendable version, "SUPER LOW" design, approx. 7,550 mm long - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking device - Service lines are protected within the extendable beams and automatically adjust to the lowbed length Rear Undercarriage: - Rear chassis with closed outer frame, checker plate cover, and continuous prism-shaped excavator trough approx. 1,450/900 x 505 mm, open at the rear - 2 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame Axles and Tires: - "PENDULUM AXLE", all axles hydro-mechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function Lhjdpfxeh Hm Tho Aa Rec - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 / 3PMSF Included Accessories: - Prepared for bolt-on container positioning for 1x 20ft or 1x 40ft container on the outer beams - 2" kingpin - Galvanized steel front wall approx. 400 mm high - One spare wheel with holder - At the galvanized front adapter bar yellow-red air couplings - 4 wheel chocks - Remote rear steering from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Hydraulic line connections from gooseneck to lowbed with multi-coupling instead of screw coupling - Electro-hydraulic power pack - White reflective tape to EU specifications on sides, extension, and rear red - 2 wooden blocks 500x250x200 mm - European reflective plates (red-yellow) on the trailer rear - At the gooseneck and rear wall left and right each a bracket for warning boards including socket - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 - Load gauge for determination of axle loads including load diagram - On the gooseneck, plug-in ALU side and rear boards approx. 2,000 x 400 mm - The rear galvanized insert posts are removable (body length approx. 2,120 mm) - Separate air connection for air gun on the gooseneck - Duomatic air coupling from gooseneck to lowbed - Rear upper section of gooseneck closed with removable cover - 1 pair of steel ramps to bridge the lowbed's pick-up hooks - Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm - Wireless remote control for rear steering in addition to cable remote, with signal lights at receiver for single-track monitoring - 6 pairs of threaded blocks between lashing rings under the top chord on the outer beams for mounting screwable RUD rings VLBG-4 - 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading bed - Foldable extensions, approx. 230 mm per side - Loading area features a painted sand layer for anti-slip protection - Dipper stick trough of rear chassis closed at front and rear with plug-in plates - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - alu 15%)

Stanje: zelo dobro (rabljeno), prva registracija: 07/2021, dolžina tovornega prostora: 134.500 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 770 mm, skupna dolžina: 134.500 mm, skupna širina: 2.550 mm, skupna višina: 770 mm, barva: drugo, Leto izdelave: 2021, Oprema: ABS, = Dodatne možnosti in oprema = - Zračno vzmetenje = Dodatne informacije = Lastna teža: 8.520 kg Nosilnost: 31.000 kg Skupna masa: 50.900 kg Višina nakladalne površine: 77 cm Tehnično stanje: zelo dobro Vizualno stanje: zelo dobro Ljdpfx Ajutngcea Rohc Poškodbe: nobene

Stanje: novo, konfiguracija osi: 2 osi, dolžina tovornega prostora: 18.700 mm, širina tovornega prostora: 3.000 mm, višina nakladalnega prostora: 350 mm, skupna dolžina: 18.700 mm, skupna širina: 3.000 mm, skupna višina: 350 mm, vzmetenje: hidravlika, velikost pnevmatike: Tyres: 245 / 70 R17.5 Double fitted (load index 146/146 F), barva: rdeča, Leto izdelave: 2025, Details Trailer ID-Number: BO.0618 Manufacturer: Faymonville Type: MAX510 / F-S42-2GXX Year: New Axles Axle Type: Pendle axle Tires: 245 / 70 R17.5, twin tyres (load index 146/146 F) Suspension: Hydraulic suspension Steering: Hydraulic steering Capacity Total axle capacity: 24,000 kg (2 x 12,000 kg) King pin load: 23,000 kg Gross vehicle weight (GVW): 47,000 kg Unladen weight: 13,211 kg Payload capacity: 33,789 kg Dimensions Length: 13,200 mm – 18,700 mm Gooseneck length: 3,750 mm Loading platform length: 6,850 mm Loading platform extension: 5,500 mm Maximum loading platform length: approx. 12,350 mm (6,850 mm + 5,500 mm) Platform width: 2,550 mm / 3,000 mm Deck height: 350 mm Ground clearance under deck: 150 mm Bogey length: 2,600 mm Additional Equipment -NATO connector -Extendable "super low" deck -Lashing rings -Twist locks for 20’, 30’ and 40’ containers -Foldable outriggers and loading planks -Ramps for access to the loading deck -Wired and radio remote control -Spare wheel with holder -Work lamps -Rear underrun bar with lights -Holder for one warning beacon -King pin 3.5” fitted, 2.0” spare -Holder for warning boards and socket -Hydro-electric pump on gooseneck -Marker boards for oversize transport -Quick couplers -Excavator trough -Gooseneck hydraulically liftable, lowerable and detachable = Further information = General Information Year of manufacture: 2025 Applications: Agriculture, Forestry, Construction, Drainage, Fruit Cultivation, Earthmoving, Terrain Management, Internal Logistics, Crop Production, Mining, Land Drainage, Site Management, Recycling, Cleaning, Demolition, Horticulture, Animal Husbandry and Road Construction Axle configuration Tyre size: 245 / 70 R17.5, twin tyres (load index 146/146 F) Suspension: Hydraulic suspension Rear axle 1: Twin tyres; Max. axle load: 12,000 kg; Steered Rear axle 2: Twin tyres; Max. axle load: 12,000 kg; Steered Weights Unladen weight: 13,211 kg Payload: 33,789 kg Gross vehicle weight: 47,000 kg Functional Extendable body: Yes Condition General condition: Good Technical condition: Good Visual condition: Good Financial Information Price: On request Lsdpfoxyihhsx Aa Rjhc Further Information Please contact Stefan Schaapveld for further details.

Stanje: rabljeno, največja dovoljena obremenitev: 57.900 kg, skupna masa: 73.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/2024, naslednji pregled (TÜV): 07/2026, skupna širina: 2.540 mm, Oprema: ABS, Our complete inventory of vehicles, including models available for immediate or short-term delivery, is available on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: * Gooseneck in SNT design for optimized loading area length, approx. 3,700 mm long * Gooseneck tapered at the rear, approx. 1,000 mm x 10° * Technical fifth wheel load: 30,000 kg; suitable for tractor units: 4x2, 6x2, and 6x4 Loading Area: * Extendable loading area, approx. 8,800 mm long, with rear tapering approx. 500 mm x 10° Axles and Suspension: * BPW axles and suspension * 1st axle with hydraulic steering and electro-magnetic reverse lock, all other axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg per axle Ledpfx Aoxuyproa Rjhc * Air suspension with lift and lower valve Tyres: * 235/75 R 17.5 3PMSF twin tyres, load index 143/141J (144/144F) Braking System: * WABCO EBS-E braking system compliant with EU regulations Paintwork: * Trailer colour: RAL 3002 Carmine Red Included Accessories: * Plug-in steel front wall, approx. 400 mm high * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 3 kW electro-hydraulic power unit for hydraulic functions (excluding hydraulic winches), without installation of supply connections to the tractor unit * Parking position for warning signs on the gooseneck when not in use * 1 mounting adapter for E-wheel in front of the gooseneck bulkhead (without E-wheel) * External carrier on the gooseneck with fixing bores for bolted lashing rings. First bore approx. 200 mm from the front, then every approx. 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of removable ALU side walls on the gooseneck, approx. 400 mm high, anodized finish * 1 removable ALU rear wall on the gooseneck, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor on the gooseneck, chequered plate above the king pin * 2 inch king pin * Mechanical landing legs with 2-speed gearbox and JOST Modul B crank * Continuous approx. 50 mm thick hardwood floor on loading area and interrupted between the axles * Securing of the loading area with conically welded locking profiles approx. every 500 mm * Long holes for detachable and repositionable bridging elements: - at the front of the loading area * 1 movable intermediate table, approx. 300 mm wide, for the draw-out tube with large cross-section, with chequered plate surface; at front and rear with long holes for attachable and repositionable bridging elements * 1 pair of lashing rings on the front cross-member (LC 10,000 daN) * 7 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards (LC 10,000 daN) * Extendable (galvanized) widening elements, approx. 230 mm per side (without timber planks) * 1 pair of mechanical rear supports * Remote steering from front and rear using cable remote control with push-button operation; single-track alignment of axles, without installation in the tractor unit * Cable (approx. 35 mm², approx. 3.5 m long) for supplying the electro-hydraulic unit and/or electric winch between trailer and tractor unit with plug (NATO-NATO) * 2 additional pairs of bolted lashing rings (LC 5,000 daN) * 1 single-piece INOX toolbox, approx. 2,480 x 340 x 390 mm (L x W x H), straight design, with two side exterior doors and one top lid, located behind the front wall.

Stanje: rabljeno, konfiguracija osi: 3 osi, prva registracija: 10/2006, skupna širina: 2.850 mm, vzmetenje: drugo, velikost pnevmatike: 285/70R19.5, barva: črn, Leto izdelave: 2006, Oprema: ABS, = Additional Options and Accessories = - Central lubrication system = Notes = Faymonville Jeep Dolly D3 Year: 10/2006. 1 x lift axle. 1 x friction-steered axle / trailing steering. Air suspension. Max. technical weight: 56,000 kg. Lhsdpfx Asxbng Eea Rec Faymonville STBZ-5VA Year: 10/2006. Pendle axle. Removable gooseneck. Adjustable load platform. Extendable bed: 400 cm. Loading deck: 650 + 400 cm. Fifth wheel load: 50,000 kg. Max. technical weight: 119,680 kg. = Further Information = Axle Configuration Tyre size: 285/70R19.5 Brakes: Drum brakes Front axle 1: Twin tyres; Tread left inside: 15%; Tread left outside: 60%; Tread right inside: 60%; Tread right outside: 60%; Suspension: Air suspension Front axle 2: Twin tyres; Tread left inside: 30%; Tread left outside: 30%; Tread right inside: 40%; Tread right outside: 60%; Suspension: Air suspension Front axle 3: Twin tyres; Steering; Tread left inside: 30%; Tread left outside: 70%; Tread right inside: 60%; Tread right outside: 70%; Suspension: Air suspension Rear axle 1: Twin tyres; Steering; Tread left inside: 30%; Tread left outside: 60%; Tread right inside: 40%; Tread right outside: 70%; Suspension: Hydraulic suspension Rear axle 2: Twin tyres; Steering; Tread left inside: 50%; Tread left outside: 50%; Tread right inside: 30%; Tread right outside: 75%; Suspension: Hydraulic suspension Rear axle 3: Twin tyres; Steering; Tread left inside: 60%; Tread left outside: 60%; Tread right inside: 60%; Tread right outside: 60%; Suspension: Hydraulic suspension Rear axle 4: Twin tyres; Steering; Tread left inside: 60%; Tread left outside: 60%; Tread right inside: 40%; Tread right outside: 50%; Suspension: Hydraulic suspension Rear axle 5: Twin tyres; Steering; Tread left inside: 70%; Tread left outside: 70%; Tread right inside: 20%; Tread right outside: 70%; Suspension: Hydraulic suspension Weights Unladen weight: 36,600 kg Payload: 83,080 kg Gross Vehicle Weight (GVW): 119,680 kg Financial Information Price: On request Identification Model number: STBZ-5VA + 3 AXLE JEEP DOLLY / E = Company Information = ALL PRICES ARE NET FOR EXPORT. Joris Versteijnen (NL-DE-EN) Wouter Greutink (NL-DE-EN-ES-IT). We speak Russian. We strive to provide correct information, but no rights can be derived from the texts provided.

Stanje: novo, konfiguracija osi: 3 osi, skupna dolžina: 17.700 mm, skupna širina: 2.990 mm, skupna višina: 3.810 mm, vzmetenje: hidravlika, velikost pnevmatike: 245/70 R17.5 Double Fitted (143/141J), barva: rdeča, Leto izdelave: 2024, Oprema: dvižna zadnja plošča, Color: Red Payload: 100,250 kg Weights: - King-pin load: 38,000 kg - Axle load: 12,000 kg - Total axle load: 96,000 kg Ledsuu E Tijpfx Aa Rohc - Gross vehicle weight (GVW): 134,000 kg - Unladen weight: 33,750 kg - Payload capacity: 100,250 kg Axles: - Axle brand: BPW ECO PLUS - Hydraulic suspension - 7 steered axles (2nd axle fixed) - First two axles liftable - Drum brakes - Brake system SN 3020 for ABS with sensors - Tyres: 245/70 R17.5 dual mounted - Load index: 143/141J Dimensions: - Length: 17,700 mm - Extended length: 19,500 mm - Maximum extended length: 37,900 mm - Loading floor width: 3,990 / 3,450 mm - Loading floor height: 1,050 mm ±150 mm - Height: 3,815 mm Additional equipment: - NATO plug - Hydraulically foldable ramps - Outriggers and planks for widening the loading platform - Electro-hydraulic pump for trailer functions - Spare wheel with holder - Work lights - Rear underrun protection with integrated lights - 2-inch king-pin - Centralized greasing system - Lashing rings - Wooden loading floor - Oversize load marker boards - Remote control General Information: Year of manufacture: 2024 Axle Configuration: - Tyre size: 245/70 R17.5 dual fitted (143/141J) - Axle brand: BPW ECO PLUS - Brakes: drum brakes - Suspension: hydraulic suspension Rear Axle 1: Dual tyres; Lift axle; Max axle load: 12,000 kg; Steered; Tyre tread depth left inner: 100%; left outer: 100%; right inner: 100%; right outer: 100% Rear Axle 2: Dual tyres; Lift axle; Max axle load: 12,000 kg; Tyre tread depth left inner: 100%; left outer: 100%; right inner: 100%; right outer: 100% Rear Axle 3: Dual tyres; Max axle load: 12,000 kg; Steered; Tyre tread depth left inner: 100%; left outer: 100%; right inner: 100%; right outer: 100% Rear Axles 4-8: Dual tyres; Max axle load: 12,000 kg; Steered; Tyre tread depth left inner: 100%; left outer: 100%; right inner: 100%; right outer: 100% Weights: - Unladen weight: 33,750 kg - Permissible payload: 100,250 kg - Gross vehicle weight: 134,000 kg Functionality: - Loading platform height: 105 cm - Extendable body: Yes Condition: - Overall condition: Very good - Technical condition: Very good - Visual condition: Very good Financial Information: - Price: On request Further information: Please contact Stefan Schaapveld for more details...