Polpriklopnik z nizko nakladalno ploščadjo

FAYMONVILLE MAX Trailer MAX100 Semi-Tieflader Radmulden

Stanje: rabljeno, največja dovoljena obremenitev: 37.950 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 02/2024, naslednji pregled (TÜV): 02/2026, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory, including immediately and soon-available vehicles, on our website. Selection of equipment features. Complete list of specifications available upon request. Gooseneck: * Gooseneck with approx. 45° chamfered front corners and rear taper approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Telescopic loading area with rear taper approx. 1,000 mm x 8° * 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing bars approx. 15 x 15 mm as well as extensions in the lower section * Between 1st and 2nd axle, 1 pair of fixed wheel recesses with covers, approx. 1,610 x 700 x 400 mm (L x W x D) * Recess in the rear slope and extending into the loading area for the excavator arm, approx. 2,900 x 750 x 210/290 mm (L x W x H) * 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) * 5 pairs of outward folding lashing rings (LC 5,000 daN) * 2 pairs of outward folding lashing rings (LC 10,000 daN) * Cutouts in the external frame of the loading area for hooking in tension belts (LC 2,000 daN) * Incl. 3-piece removable galvanized covers over wheel recess – max. concentrated load approx. 3.5 t / each Axles: * BPW axles and suspension, 2 rigid axles, 3rd axle self-steering Kdjdoyc Axyjpfx Ab Hei * Technical axle load: 12,000 kg each * Electromagnetic reversing lock can be activated via reverse gear and manually * Air suspension with lift/lower valve * Axle toolkit Tyres: * 235/75 R 17.5 3PMSF tyres Landing gear: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lift capacity (approx. 50 t tested load) Brake system: * Brake system in accordance with EU regulations with EBS-E (2S2M), without connecting lines to the tractor unit Steel structure: * Steel structure made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (Yield strength 355 MPa); S690QL/S700MC (Yield strength 690 MPa) Paintwork: * Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer * High-quality single-colour top coat with a two-component (2K) paint in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) Included accessories: * 2-inch king pin * 1 galvanized steel front wall, approx. 400 mm high * 1 spare wheel holder in front of the front wall * Yellow-red air couplings on the galvanized connection rail at the front * 4 wheel chocks with holders on the front wall * Mounting at the rear of the gooseneck for aluminium loading ramps * Galvanized folding supports under the rear slope of the loading area * Bracket for a beacon at the rear of the trailer * Yellow reflector tape as per EU regulations on the sides, extension and rear of the trailer * Brackets for warning boards including sockets on left and right of gooseneck and rear plate * Mud flap at the rear of the trailer * Manual and documentation on USB stick * Bracket for beacon on warning boards * European reflective plates (red-yellow) at the rear of the trailer * Speed stickers 80 km/h at the rear and on both sides * Load gauge for axle load determination incl. load diagram * Detachable aluminium side and rear boards on the gooseneck, approx. 2,440 x 400 mm (L x H) * The rear galvanized stake pockets are removable (body length approx. 2,560 mm) * A tool ...

Stanje: novo, lastna masa: 17.250 kg, največja dovoljena obremenitev: 48.700 kg, skupna masa: 66.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 375 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 17.250 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize loading platform length, approximately 3,750 mm long - Gooseneck hydraulically liftable, lowerable, and detachable - For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Lowbed: - Lowbed with external beams, designed as a telescopic vessel bridge in low-profile construction with front extension - Length x width approx. 7,550 mm x 2,740 mm - Mechanical locking of the extension Chassis: - Rear chassis with closed outer frame - Checker plate surface and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, Suspension, and Tyres: - “PENDEL-AXLE”, all axles hydromechanically forced steered - Burst protection valve on the axle compensation cylinders with automatic reset function - Hydraulic cylinders with shut-off valves and plug pins for securing in raised position - Final coating of axles: two coats of single-color 2-component paint in "FAY-Grey-34-0260" - Technical axle load 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 Accessories: - Detachable steel front wall, approx. 400 mm high - 4 wheel chocks - Rear upper gooseneck area closed with removable cover - 1 pair of steel ramps with climbing bars and locking bolts to bridge the lowbed mounting hooks - Ramps can be positioned over or between the hooks - Mounting options for steel drive-on ramps at the rear, between the outer beams of the gooseneck - Locking point approx. every 1,000 mm on the extension - 1 lashing ring each, left and right, on the front cross member - Supply line connection strip for tractor unit, mounted at the height of outer frame profile - 6 pairs of threaded blocks on the exterior of the load floor inner beams for attaching M24 screw rings - 6 pairs of recessed lashing rings on the outside of the load floor outer beams, foldable inwards and outwards - 1 pair of threaded blocks on the front and rear of the load floor outer beams for M24 screw rings - Mounting rail for loose aluminum approach ramps on the end cross member of the vehicle - Central lubrication system with 2 pumps, brand BEKAMAX - Remote steering front and rear, cable remote controlled, with axle tracking control - 3 kW electro-hydraulic power unit for hydraulic operations, except hydraulic winches Kdodpfx Aoh Hm Tzob Hei - Removable galvanized loading floor, can be placed in 3 elements between the outer beams, with hardwood covering - Foldable extensions, approx. 230 mm per side - Loose extension boards, steel-edged - 4 warning signs approx. 423 x 423 mm - Radio remote control for rear steering - 3.5” kingpin - Anti-slip coating on the left chamfer of the gooseneck - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Guide plate from gooseneck for the fifth wheel plate, approx. 800 mm wide - 1 spare wheel with mounting adapter - Parking position on the gooseneck for warning signs when not in use - 2 pairs of stake pockets integrated into the chassis outer frame, for plug-in stakes approx. 100 x 50 mm - Excavator stick trough of rear chassis closed at the rear with a removable plate - Trailer color: Mercedes-Benz 7350 Novagrey

Stanje: novo, največja dovoljena obremenitev: 36.360 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment details available upon request. Neck (Gooseneck): * Gooseneck with front corners tapered approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Extendable loading area with rear bevel approx. 1,000 mm x 8° * 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm (L x W x D) * Wheel recesses with square profile climbing strips approx. 15 x 15 mm as well as lower-width extensions * Between the first and second axle: one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) * Incl. 3-piece removable galvanized covers over the wheel recesses (approx. 670 mm wide) – max. point load 5 t/each * Recess in the bevel as well as projecting into the loading area for excavator dipper stick accommodation (approx. 2,900 x 750 x 210/290 mm [L x W x H]) * 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 2 pairs of fold-out lashing rings (LC 10,000 daN) * 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) * Cutouts in the outer frame of the loading area for fastening ratchet straps (LC 2,000 daN) Two-part steel ramps: * One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm hardwood covering * Ramp with hydraulically folding ramp sections and hydraulic lifting mechanism, hydraulically movable * Maximum load per pair: 40,000 kg Landing legs: JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated via reverse gear and manually * Air suspension with lifting and lowering valve Tyres: * Tyres 235/75 R 17.5 3PMSF – manufacturer of our choice TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Kodpfsyhkq Ujx Ab Hodi Braking system: * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure the best corrosion protection * Final painting with 2 coats of 2-component topcoat, single-colour in RAL 3002 Carmine Red, according to the RAL 841GL system * Rims in silver grey Including the following additional equipment: * 2" kingpin * Galvanized steel front wall, approx. 400 mm high * 3 pairs of recessed lashing rings along the central beam (LC 5,000 daN) * Rear electro-hydraulic unit, under the loading area * On the gooseneck, aluminium side and rear plug-in walls, approx. 2,440 x 400 mm (L x H). The rear galvanized stanchions are removable. (Superstructure length approx. 2,560 mm) * One galvanized toolbox integrated in the tapered gooseneck * 2 pairs of WADER container pockets in the loading area for one 20' or 30' container * 3 pairs of stanchion pockets for plug-in stanchions approx. 100 x 50 mm in the outer frame of the loading area * 3 additional pairs of removable, galvanized covers over the wheel recess – max. point load 3.5 t/pc * One removable galvanized intermediate table with 1 pair of WADER container pockets * 1 additional, hang-in intermediate table, approx. 300 mm wide * Interm

Stanje: novo, največja dovoljena obremenitev: 37.820 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Excerpt from the equipment. Complete specification available on request. Gooseneck: - Gooseneck with front corners beveled approx. 45° and rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring approx. 30 mm thick Loading Platform: - 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) - Wheel recesses with square climbing stripes approx. 15 x 15 mm, including widenings at the bottom - Between the 1st and 2nd axles, one fixed pair of wheel recesses approx. 1,610 x 700 x 400 mm (L x W x D) - Incl. 3-part removable galvanized covers over the wheel recesses (W approx. 670 mm), max. point load approx. 5 t/piece - Recess in the bevel and extending into the loading platform for accommodating excavator stick (approx. 2,900 x 750 x 210/290 mm (L x W x H)) - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of folding-out lashing rings (LC 5,000 daN) - 3 pairs of folding-out lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) - Cut-outs in the outer frame of the platform for attaching tension belts (LC 2,000 daN) One-Piece Steel Ramps: - 1 pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering - Ramp with hydraulic lifting system, hydraulically adjustable - Maximum load per pair: 40,000 kg - In accordance with Regulation 1230/2012/EU, ramps shorter than 300 mm do not need to be considered in the vehicle length in transport position Landing Gear: - JOST landing gears (mechanical) with 2-speed gearbox for approx. 24 t lift capacity (approx. 50 t test load) Axles: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load per axle: 12,000 kg - Electro-magnetic reverse lockout, activated via reverse gear and manually - Air suspension with raise/lower valve - Axle tool Tyres: - Tyres 235/75 R 17.5 3PMSF, brand of our choice - TPMS tyre monitoring system as per ECE R 141. Data transmission to the tractor unit via the standardized EBS interface according to ISO 11992. To display correctly, the tractor unit must be able to receive and show this data. Brake System: - WABCO brake system in compliance with EU regulations, with EBS-E (2S2M) without connecting lines to the tractor unit Steel Construction: - Steel structure made from high-tensile fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355MPa); S690QL/S700MC (yield strength 690MPa) Electrical System: - Electrical system in accordance with EU regulations - 24 Volt lighting ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at the front terminal bar with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - Complete steel structure automatically shot blasted with a turbine blasting system after welding Kedpfow Tpqwox Ab Hedi - Second blasting process with corundum for optimum coating adhesion - HRM metallization of the entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for optimal corrosion protection - Final paint with two layers of 2K topcoat, single color in RAL 3002 Carmine Red, according to the RAL 841GL system - Rims in silver - Rear section metallized and in RAL 9010 (con...

Stanje: novo, lastna masa: 17.500 kg, največja dovoljena obremenitev: 43.500 kg, skupna masa: 61.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.750 mm, višina nakladalnega prostora: 400 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - For tractor units: 6x4 or 8x4 Lowbed: - Lowbed with external beams, extendable version, "SUPER LOW" design, approx. 7,550 mm long - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking device - Service lines are protected within the extendable beams and automatically adjust to the lowbed length Rear Undercarriage: - Rear chassis with closed outer frame, checker plate cover, and continuous prism-shaped excavator trough approx. 1,450/900 x 505 mm, open at the rear - 2 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame Axles and Tires: - "PENDULUM AXLE", all axles hydro-mechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 / 3PMSF Included Accessories: - Prepared for bolt-on container positioning for 1x 20ft or 1x 40ft container on the outer beams - 2" kingpin - Galvanized steel front wall approx. 400 mm high - One spare wheel with holder Kodpsh Hm Thsfx Ab Hsdi - At the galvanized front adapter bar yellow-red air couplings - 4 wheel chocks - Remote rear steering from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Hydraulic line connections from gooseneck to lowbed with multi-coupling instead of screw coupling - Electro-hydraulic power pack - White reflective tape to EU specifications on sides, extension, and rear red - 2 wooden blocks 500x250x200 mm - European reflective plates (red-yellow) on the trailer rear - At the gooseneck and rear wall left and right each a bracket for warning boards including socket - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 - Load gauge for determination of axle loads including load diagram - On the gooseneck, plug-in ALU side and rear boards approx. 2,000 x 400 mm - The rear galvanized insert posts are removable (body length approx. 2,120 mm) - Separate air connection for air gun on the gooseneck - Duomatic air coupling from gooseneck to lowbed - Rear upper section of gooseneck closed with removable cover - 1 pair of steel ramps to bridge the lowbed's pick-up hooks - Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm - Wireless remote control for rear steering in addition to cable remote, with signal lights at receiver for single-track monitoring - 6 pairs of threaded blocks between lashing rings under the top chord on the outer beams for mounting screwable RUD rings VLBG-4 - 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading bed - Foldable extensions, approx. 230 mm per side - Loading area features a painted sand layer for anti-slip protection - Dipper stick trough of rear chassis closed at front and rear with plug-in plates - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - alu 15%)

Stanje: novo, največja dovoljena obremenitev: 37.635 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete stock of vehicles, including those available immediately or at short notice, can be found on our website. Excerpt from the equipment features. Full equipment list available on request. Gooseneck: * Gooseneck with beveled front corners approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick One-piece steel ramps: * One pair of galvanized, one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering * Ramp with hydraulic lifting mechanism, hydraulically adjustable * Maximum load per pair: 40,000 kg In accordance with Regulation 1230/2012/EU, ramps with a length less than 300 mm do not need to be included in the vehicle length when in transport position Loading platform: * 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing strips approx. 15 x 15 mm and extensions at the lower section * Between the 1st and 2nd axle, one pair of fixed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D). Includes 3-piece removable galvanized covers over the wheel recesses (approx. 670 mm wide) - max. point load 5 t/piece * Recess in the chamfer and extending into the loading platform for excavator boom (approx. 2,900 x 750 x 210/290 mm (L x W x H)) * 1 pair of flat lashing rings at the front of the loading platform (LC 10,000 daN) * 5 pairs of outward folding lashing rings (LC 5,000 daN) * 3 pairs of outward folding lashing rings (LC 10,000 daN). 2 pairs of lashing rings in the excavator boom recess (LC 5,000 daN) * Cut-outs in the outer frame of the platform for securing straps (LC 2,000 daN) Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t static test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 trailing steering axle * Technical axle load: 12,000 kg each * Electromagnetic reversing lock, activated via reverse gear and manually * Air suspension with lift and lowering valve * Axle tools Tyres: * Tyres 235/75 R 17.5 3PMSF – manufacturer at our discretion * TPMS: Tyre Pressure Monitoring System in accordance with ECE R 141. Data transmission to the towing vehicle via the standardised EBS interface per ISO 11992. For correct display, the towing vehicle must be able to relay and display this data Braking system: * WABCO braking system compliant with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Steel structure: * Steel structure made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Electrical system: * Electrical system compliant with EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting * ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets * Connections as per ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paint finish: * Complete steel structure automatically blasted with turbine blasting machine after welding * Secondary shot-blasting with corundum for optimum coating adhesion * Top coat: 2 layers of 2K finish, single colour in RAL 3002 Carmine Red, as per RAL system 841GL * Wheels in silver Kdodpoxtc Ubjfx Ab Hji * Rear section metallized and painted in RAL 9010 (Pure White) * Paint system tested with salt spray test in accordance with ISO 9227-NSS * Cavity sealing with specialist wax Including the following additional equipment: * 2-inch king pin * One ver

Stanje: novo, največja dovoljena obremenitev: 50.400 kg, skupna masa: 65.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment specification. Full specification available on request. GOOSENECK * Gooseneck in SNT design to optimize platform length, approx. length 3,700 mm, with rear bevel of approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX at the front connection rail with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, except for hydraulic winches * 1 pair of detachable ALU side walls, approx. 400 mm high, anodized finish * 1 detachable ALU rear wall, approx. 400 mm high, anodized finish * Over the gooseneck, approx. 40 mm thick hardwood flooring, over the king pin with checker plate covering * 2-inch king pin * Mount at the rear of the gooseneck for ALU drive-on ramps * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) LOAD PLATFORM * Extendable load platform, approx. length 8,800 mm, with rear bevel approx. 500 mm x 10° Kodotx Nwnspfx Ab Hjdi * Recess in platform and rear bevel for accommodating an excavator dipper stick, approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st axle self-steering, all other axles hydro-mechanically forced steered * 1st axle with electromagnetic reversing lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with lift and lower valve * Tires: 235/75 R 17.5 3PMSF twin tires * Mechanical landing legs with 2-speed gearbox and crank, JOST Modul B - static test load = approx. 50,000 kg * Platform with continuous and between-axles interrupted 50 mm thick hardwood flooring (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable galvanized side extensions by approx. 230 mm each side (without wooden planks) * Wheel wells with square climbing strips, approx. 15 x 15 mm in front of the axles, continuous opening up to the cross member of the gooseneck, approx. 700 x 410 mm (W x D) * ALU covers for the wheel wells, usable as bridging elements for the extension OR as width extension planks * Lockable aluminium elements on the extension tubes of the side extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel wells with square climbing strips, approx. 15 x 15 mm between the 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * ALU covers for the wheel wells, usable as bridging elements for the extension OR as width extension planks * Lockable aluminium elements on the extension tubes of the side extensions * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with single-track monitoring of the axles, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-part steel ramps, type: DR-15/60-900-4350-KG-HV-M, approx. length 4,350 mm and width approx. 900 mm * Hydraulically folding ramp tips * Ramps hydraulically adjustable individually by approx. 235 mm outward and approx. 215 mm inward * Super Grip rubber surface approx. 25 mm and steel surface approx. 5 mm as additional

Stanje: rabljeno, prevoženi kilometri: 71.470 km, moč: 375 kW (509,86 KM), velikost pnevmatike: 385/65 R22.5, konfiguracija osi: 6x6, barva: zelen, vrsta prenosa: samodejen, emisijski razred: Euro 6, vzmetenje: jeklo, skupna dolžina: 7.920 mm, skupna širina: 2.550 mm, skupna višina: 3.690 mm, Leto izdelave: 2024, Oprema: ABS, centralno zaklepanje, električno nastavljivo ogledalo, električno upravljanje oken, klimatska naprava, zapora diferenciala, = Dodatne opcije i oprema = - Klima uređaj - Radio - Klizni ili panoramski krov = Dodatne informacije = Ovjes: lisnate opruge Osovina 1: Dimenzije gume: 385/65 R22.5; Kočnice: disk kočnice Osovina 2: Dimenzije gume: 315/80 R22,5 Osovina 3: Dimenzije gume: 315/80 R22,5 Kedpfjxz Traex Ab Hodi Sopstvena masa: 13.537 kg Nosivost: 12.463 kg Dozvoljena ukupna masa: 26.000 kg

Stanje: novo, največja dovoljena obremenitev: 30.190 kg, skupna masa: 43.000 kg, konfiguracija osi: 2 osi, Oprema: ABS, You can find our complete vehicle inventory, including vehicles available for immediate or short-term delivery, on our website. The following is an excerpt from the specifications. Complete equipment details available upon request. Load area: - Lowbed with external beams, extendable version in SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor, approx. 40 mm thick, with mechanical locking - Supply lines are protected within the extendable beams and automatically adjust to the current lowbed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for mounting bolted RUD rings Gooseneck: - Gooseneck in SNT design to optimize load area length, approx. 3,750 mm - Gooseneck hydraulically lift/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2 Rear chassis: - Rear chassis in short version with closed outer frame and checker plate cover Kdjdpexarl Nofx Ab Hji - Chassis with excavator recess, closed in the rear half to accommodate air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings lying flat, at the front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced-steered - Technical axle load: 12,000 kg per axle - Air suspension with raise/lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF, manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system according to ECE R 141 - Data transmission to tractor via standardized EBS interface (ISO 11992) - For proper display, the tractor must be capable of transmitting and displaying these data Braking system: - Braking system according to EU regulations with EBS-E (2S2M) Electrical system: - Electrical system in accordance with EU regulations, 24-volt lighting ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with turn indicator - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: - Steel construction of high-strength fine-grain steels - Steel qualities: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Entire steel construction automatically shot-blasted after welding - Second blasting with corundum for optimal coating adhesion - Complete vehicle chassis coated with HRM metallization using ZINACOR 850 (85% zinc / 15% aluminium) for premium corrosion protection - Top coat with 2 layers of 2K paint in RAL 3002 carmine red, single-color, according to RAL system 841GL - Rims in silver - Rear section metallized and painted in RAL 9010 (pure white) - No metallic paint possible - Paint system tested in salt spray test according to ISO 9227-NSS - Cavity sealing with special wax Including the following additional equipment: - 2-inch kingpin - One galvanized steel front wall, approx. 400 mm high - Remote-steered axles from front and rear via cable control with pushbuttons, with single-track monitoring (without installation in tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupler instead of threaded couplings - Electro-hydraulic power unit - Prepared for installation of bolted container mounts for 1x 20' or 1x 40' container on outer beams - Without container locks

Stanje: novo, lastna masa: 13.500 kg, največja dovoljena obremenitev: 51.500 kg, skupna masa: 69.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimizing loading platform length, length approx. 3,700 mm Gooseneck rear with chamfering approx. 1,000 mm x 10° Loading Platform: Telescopic loading platform, length approx. 8,800 mm, with rear chamfering approx. 500 mm x 10° Recess in the chamfer as well as into the loading platform to accommodate the excavator dipper stick Pneumatic locking with conical pin and reinforced locking positions Supply lines routed protected within the extendable beam, adapting to the respective platform length Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps individually adjustable hydraulically approx. 235 mm to the outside and approx. 215 mm to the inside Axles and Suspension: BPW axles and suspension, two rigid axles, two steering trailing axles Electromagnetic reverse lock, activated via reverse gear and manually Air suspension with lift and lower valve Axle tool Tyres: 235/75 R17.5 3PMSF twin tyres Load index: 143/141J (144/144F) Brake System: WABCO braking system, EBS-E in accordance with EU regulations Lighting System: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Metalizing: Standard HRM metallization of the outer frame Complete steel structure shot-blasted, then visible defined surfaces metallized with ZINACOR 850 (Zinc 85% - Alu 15%) hot-refined Steel Construction: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified as per DIN-EN 287-1 MAG welding process according to EN ISO 4063 Shielding gas M21 as per EN ISO 14175 Accessories Included: Front wall made of steel, plug-in, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin 24N connection per ISO-11852, 24S connection per ISO-3731, 15-pin connection per ISO-12098 Round NATO socket on the front connection strip Cable to supply electro-hydraulic unit and/or electric winch (35 mm², 3.5 m long) between trailer and tractor with connector (NATO-NATO) 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches 1 spare wheel with mounting adapter Outer beam of the gooseneck with fastening holes for screwable lashing rings. The first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included One fastening hole in the rear upper area of the gooseneck's outer beam for a screwable lashing ring 1 pair of screw-in lashing rings Approx. 40 mm thick hardwood covering above the gooseneck On the gooseneck, 1 pair of plug-in side aluminium walls, approx. 400 mm high, anodized Kjdpfxek Ahugj Ab Hjdi On the gooseneck, a plug-in aluminium rear wall, approx. 400 mm high, anodized 2" kingpin Gooseneck guide plate for fifth wheel, approx. 500 mm wide 4 wheel chocks with holder Holder for aluminium approach ramps Mechanical landing gear with 2-speed gearbox and crank Continuous hardwood floor approx. 50 mm thick on the loading platform, interrupted between axles Platform locking with conically welded locking profiles every 250 mm incl. tension plate Slotted holes at the front of the loading platform for attachable and adjustable bridging elements 1 intermediate table with recessed platform, approx. 300 mm wide for the draw-out tube with large cross-section, with sheet metal covering Front and rear with slotted holes