Faymonville Faymonville F-S43-1Aaf / Raztegljiv / Hidravlične Rampe nakup rabljenega (28.847)

Stanje: novo, lastna masa: 12.900 kg, največja dovoljena obremenitev: 34.100 kg, skupna masa: 47.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 350 mm, vzmetenje: drugo, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 12.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm in length - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2, and 6x4 Loading Platform: - Low-bed with external beams, extendable “SUPER LOW” design, approx. 6,850 mm in length - Low-bed with fixed hardwood flooring, approx. 40 mm thick, with mechanical locking device Rear Chassis: - Rear chassis with closed outer frame, chequer plate covering, and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings, foldable to the outside - 1 pair of lashing rings recessed in the trough - 2 pairs of stake pockets for insertable stakes 100 x 50 mm in the external frame Blsdpfx Aehlz R Somtoi Pendulum Axle and Tyres: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and safety locking pins for securing in raised position - Axles painted with two layers of single-colour 2K paint in “FAY-Grey-34-0260” - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 - TPMS tyre pressure monitoring system according to ECE R 141 Accessories: - Preparation for the installation of bolt-on container locators for 1 x 20ft or 1 x 40ft container on the outer girders - 2" king pin - One galvanized steel front wall, approx. 400 mm high - One spare wheel - Yellow-red air couplers on the galvanized front connection bar - 4 wheel chocks - Remote steering from front and rear, operable via wired remote control with push buttons, with single-track alignment control - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of screw couplings - Electro-hydraulic power unit - White reflective tape in accordance with EU regulations on sides, extension, and rear - European reflective plates (red-yellow) on the rear of the trailer - One bracket on each side of gooseneck and rear plate for warning panels, including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on outer beam for mounting screw-on RUD Rings VLBG-4 - Detachable ALU side boards and rear board on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized insertable stakes are removable (body length approx. 2,560 mm) - Gooseneck rear upper area covered with removable cover - 5 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading area - Folding extensions, approx. 230 mm per side - 2 pairs of bolted RUD Rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the mounting hooks of the low-bed - Anti-skid sand layer painted on loading surface - 80 km/h speed stickers at rear and both sides - Spoon boom trough at rear chassis closed at rear with plug-in plate - Four extendable warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for rear axle steering in addition to cable remote, with indicator lights on receiver for alignment control - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard NLGI-2 grease - Load pressure gauge for determining axle loads - HRM Metallisation (High Resistance Metallisation) of outer frame - Complete steel structure shot blasted, then all defined visible areas metallized and finished with ZINACOR 850 (zinc 85% - aluminium 15%) hot galvanizing

Stanje: novo, lastna masa: 15.450 kg, največja dovoljena obremenitev: 65.550 kg, skupna masa: 80.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 21.900 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 925 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimized platform length, approx. 3,700 mm long, with rear tapering of approx. 1,000 mm x 10° Technical fifth wheel load: 30,000 kg. For tractors: 4x2, 6x2, and 6x4 Loading Platform: Double-extendable loading platform, approx. 8,800 mm long with rear taper of approx. 500 mm x 10°. A support table approx. 300 mm wide is welded to the central beam, featuring elongated slots at the front and rear for optional bridge elements that can be hooked in and repositioned Pneumatic locking with conical locking pin and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles and Tyres: BPW axles and suspension, first axle self-steering, all other axles hydraulically and mechanically forced-steered First axle equipped with an electro-magnetic reverse lockout, activated via reverse gear and manually. Technical axle load: 12,000 kg. Air suspension with lift and lower valve Manufacturer by our choice Sockets and Lighting: 24-volt lighting system in accordance with EU regulations ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Complete HRM metallizing Full steel construction, shot-blasted, then hot-finished with ZINACOR 850 Paintwork: 6-stage finishing process: Complete steel construction shot-blasted after welding 1 coat of zinc-based primer, 1 coat of adhesion primer. Final paintwork in 2 coats of 2K paint in single-tone DB 7350 Novagrau, followed by cavity sealing with special wax Accessories: Bsdpferigw Rox Amteli Detachable front wall made of steel, approx. 400 mm high Connection strip for supply lines to the tractor unit, fitted at the height of the outer frame profile ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets. If your pin configuration deviates from the ISO connector standard, please inform us 3 kW electro-hydraulic power unit for hydraulic functions (excluding hydraulic winches) 1 pair of plug-in ALU sidewalls on the gooseneck, approx. 400 mm high, anodized finish 3.5'' king pin. Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide 2 wheel chocks with holder in front of the front wall Mechanical landing legs with 2-speed gearbox and crank Control valves for hydraulic ramps located on the right side of the vehicle 1 pair of mechanical rear supports Central lubrication system with 1 pump, BEKAMAX brand, using standard grease according to NLGI-2 Removable guard covering the pump(s) of the central lubrication system Remote steering from front and rear, controlled by cable remote with push buttons, with axle tracking control, no installation required on tractor unit Under the gooseneck and on the rear crossmember, one 7-pin socket with holder for warning signs each on left and right. One 7-pin socket on the rear crossmember Manual and documentation One-piece INOX stowage box, approx. 2,480 x 340 x 390 mm, straight design Please note that any special equipment and accessories will increase the unladen weight and correspondingly reduce the payload Warning package: 4 warning boards, approx. 423 x 423 mm, extendable by approx. 1,000 mm, incl. 2 LED position lights and brackets for beacon.

Stanje: novo, lastna masa: 34.500 kg, največja dovoljena obremenitev: 106.700 kg, skupna masa: 141.200 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.150 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 580 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, obratovalna teža: 34.500 kg, Oprema: ABS, Gooseneck: - Gooseneck hydraulically lift/lowerable as well as detachable - Length approx. 3,650 mm - Extensive lashing positions - For tractor units: 6 x 4 or 8 x 4 3-Axle Compact Front Bogie: - Hook mounts at front and rear - Chassis length x chassis width approx. 3,560 mm x 2,850 mm - Extensive lashing positions Excavator Deck “BB-A”: - Telescopic excavator deck “BB-A” with drive-over deck hooks at the front and bolted lug coupling at the rear - Length x base width approx. 7,150 mm x 2,850 mm - Beam height x beam width approx. 430 mm x 1,350 mm - Loading height 580 mm with 150 mm ground clearance - 5 pairs of hanging lashing rings (LC 10,600 daN) - 4 pairs of threaded blocks M30 on inner beam for mounting screw-on rings 5-Axle Rear Bogie: - Mechanical bolt-on lug coupling for fitting a lowbed front, rear end traverse - Chassis length x chassis width approx. 6,840 mm x 2,850 mm - Extensive lashing positions Pendulum Axle and Tyres (front and rear bogie): - “PENDEL-AXLE”, all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-plugs for securing in lifted position - Final paint of axles with 2 coats of 2K paint, single-colour in MB 7350 Novagrau - Technical axle load: 14,640 kg (62 km/h) - Hydraulic axle compensation - Axle tools - Tyres 285/70 R19.5 Steering Override: - Remote steering from the front and rear via cable remote control with push buttons, including axle tracking control - Socket for steering control operation on the gooseneck - Cable remote control with push buttons including axle tracking control Included accessories: Blodpfx Aswhywfjmtji - Yellow-red air couplings on galvanised front connection rail - Steel headboard approx. 400 mm high - 4 wheel chocks with holders - 2 spare wheels 285/70 R19.5 - 3.5" kingpin - Gantry with winch for spare wheel at the front side of the gooseneck - Truck hydraulic connection with flow control valve (40 l/min), including gantry for suspension of supply lines, tractor unit tank must be at least 80 litres with couplings - White reflective tape according to EU regulations on sides and extension, red at rear - Plug-in ALU side panels and rear wall on gooseneck, approx. 400 mm high, anodised - Operating lever on gooseneck protected by folding cover - Separate air connection with air pistol on gooseneck - Central lubrication system BEKAMAX with standard grease NLGI-2: 1x on the gooseneck, 1x on 3-axle bogie, 1x on 5-axle bogie - Variomax tool kit - Multi-coupling hydraulic connections in the lowbed hook area - Front bogie with separate air connection for air screwdriver - Threaded inserts (ø 40 mm) every approx. 500 mm on outside of upper flange of excavator deck for screw rings - Folding extensions with steel mats, width adjustable from approx. 2,850 mm to approx. 3,250 mm - Steel mats with rubber covering approx. 12 mm thick - Two INOX toolboxes 855 x 340 x 390 mm - Radio remote control for steering override in addition to cable remote - Painted sand layer as anti-slip measure - 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery

Stanje: novo, lastna masa: 14.350 kg, največja dovoljena obremenitev: 53.450 kg, skupna masa: 67.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, dvižna zadnja plošča, Gooseneck: - Gooseneck in SNT design for optimization of loading bed length, length approx. 3,700 mm - Gooseneck rear with chamfer approx. 1,000 mm x 10° - For tractor units: 6x2, 6x4, 8x4 short Loading bed: - Extendable loading bed, length approx. 8,800 mm, rear chamfer approx. 500 mm x 10° - A recess in the loading bed and the chamfered section for receiving the excavator dipper stick, approx. 3,850 x 750 x 210/290 mm Two-part steel ramps: - One pair of two-part steel ramps, length approx. 4,350 mm, width approx. 900 mm - Ramps with rubber covering - Ramps hydraulically adjustable individually approx. 235 mm outwards and approx. 215 mm inwards - 'Super Grip' 25 mm rubber flooring and approx. 5 mm steel plate as additional reinforcement on the rear chamfer of the loading bed - Square climbing bars 20 x 30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: - BPW axles and suspension, 1st axle steering, all other axles hydromechanically forced-steered - Technical axle load: 12,000 kg Bljdpfx Aeya E A Nomtoi - 1st axle with electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Tires 235/75 R 17.5 - TPMS tire monitoring system according to ECE R141 - TPMS tire sensors fitted on all wheels, including spares Surface treatment: - Complete steel structure automatically blasted with shot blasting system after welding - Second blasting with corundum for optimum coating adhesion - HRM metallization of entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for best corrosion protection - Final painting with 2 layers of 2K top coat, single colour in MB 7350 Novagrau Accessories included: - Plug-in steel front wall, approx. 400 mm high - 3kW electro-hydraulic power unit for controlling hydraulic functions, with the exception of hydraulic winches - 1 spare wheel - Outer carrier on the gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings in the rear area of the gooseneck - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized - On the gooseneck, 1 plug-in ALU rear board, approx. 400 mm high, anodized - On top of the gooseneck, approx. 40 mm thick hardwood flooring, above kingpin area with checker plate cover - 2" kingpin - Round NATO socket on front connection strip - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front cross member - 8 pairs of recessed, fold-out lashing rings in the outer frame of the loading bed - Extendable (galvanized) widenings by approx. 230 mm per side - Wheel recesses with square climbing bars, 15 x 15 mm, in front of the axles fully open up to gooseneck cross beam, approx. 700 x 410 mm - Wheel recesses with square climbing bars, 15 x 15 mm, between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - ALU covers for wheel recesses, which can also be used as bridging elements for the extension or as widening boards - 1 pair mechanical rear supports - Radio and cable remote control - Lift axle on front axle - Square climbing bars 20 x 30 mm, approx. every 200 mm - Central lubrication system with 1 pump - Wabco Smart Board system - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, največja dovoljena obremenitev: 38.800 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5 3PMSF, barva: siv, Oprema: ABS, Swan neck: - Swan neck with front corners beveled at 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm hardwood flooring Extendable load area: - Extendable load area with rear chamfer approx. 1,000 mm x 8° - 6 pairs of fold-out lashing rings (LC 5,000 daN) - 3 pairs of fold-out lashing rings (LC 10,000 daN) - 1 pair of flat lashing rings at the front of the load area (LC 10,000 daN) - Cut-outs in the external frame of the load area for attaching lashing straps (LC 2,000 daN) - Approx. 48 mm hardwood flooring, over the axles with checker plate covering Axles and Tires: - BPW axles and suspension, 2 fixed axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated by reverse gear or manually - Air suspension with lifting and lowering valve - Axle tools - 235/75 R 17.5 tires, 3PMSF Braking system: - WABCO braking system as per EU regulations with EBS-E (2S2M) Landing legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Accessories included: - One spare wheel with holder in front of the front wall - 2'' king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection rail - 4 wheel chocks with holder at the front wall - Rear light bracket at the rear of the trailer - Mounting points at the rear area of the swan neck for ALU loading ramps - Galvanized folding supports under the chamfer of the load area - Cover plates to bridge the gap between ramps and load area - White reflective tape according to EU standards on the sides, red at the extension and rear - Electro-hydraulic unit at the rear, under the load area Bedeuqlmnepfx Amteli - Bracket for warning panels left and right on the swan neck and ramps, including power socket - Ramp control valves mounted on the right-hand side of the trailer - One mud flap at the rear of the trailer - Manual and documentation on USB stick - On the swan neck aluminum side walls and rear wall, approx. 2,440 x 400 mm - The rear galvanized stakes are removable (body length approx. 2,560 mm) - Four warning panels extendable by approx. 400 mm, size approx. 423 x 423 mm, with position light - 3 pairs of WADER container pockets in the load area for a 20ft, 30ft, or 40ft container - 6 pairs of stake pockets 100x50 mm in the external frame of the load area - Galvanized extensions, extendable by approx. 230 mm per side - Square climbing strips 20 x 20 mm every 200 mm on the outer frame of the chamfered area of the load area - Anti-slip sand layer painted on the checker plate above the king pin and load area - Mounting for beacon on the warning panels - European reflective plates (red-yellow) at the rear of the trailer - 80 km/h speed stickers at the rear and on both sides - Load gauge for determining axle loads, including load chart - HRM metallization (High Resistance Metallisation) of the external frame - Complete steel construction shot-blasted, then the defined visible surfaces finished hot-metallized with ZINACOR 850 (zinc 85% - aluminum 15%)

Stanje: novo, lastna masa: 7.900 kg, največja dovoljena obremenitev: 41.600 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, obratovalna teža: 7.900 kg, Oprema: ABS, Swan Neck: - Swan neck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood decking Loading Area: - Loading area with rear chamfer of approx. 1,000 mm x 8° - Recess in the chamfer and encroaching into the loading area for receiving the excavator bucket stick approx. 2,900 x 750 x 210/290 mm - Cut-outs in the external frame of the loading area for attaching tension straps - Hardwood decking approx. 48 mm thick, over the axles with tread plate covering Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox, 24t lifting capacity (50t test load) Axles and Tyres: - BPW axles and suspension, 2 axles rigid, 1 axle self-steering Blsdpfxjunrapj Amtji t- Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with raising and lowering valve - TPMS tyre pressure monitoring system compliant with ECE R 141 - Tyres 235/75 R 17.5 Paintwork: - Complete steel structure blasted automatically by wheel blast machine after welding - Second blasting with corundum for optimal adherence of the coating system - Final coating: two layers of 2K top coat, solid colour in RAL MB 7350 Novagrau - Rims painted silver - Rear section metallised and coated in RAL 9010 (Pure White) - Cavity sealing with special wax Electrical System: - Electrical system according to EU standards, 24 volt ASPÖCK-NORDIK (ASS3) lighting - ASPÖCK-UNIBOX at front connection rail with sockets 2x 7-pin & 1x 15-pin Included Accessories: - Multiple lashing positions - 2" king pin - One galvanised steel front wall approx. 400 mm high - Yellow-red air couplings on galvanized front connection rail - 4 wheel chocks with holders mounted on the front wall - Receiver at rear of swan neck for ALU loading ramps - Galvanised folding supports beneath rear chamfer of loading area - Bracket for beacon at rear of trailer - Galvanised extendable outriggers, extendable by approx. 230 mm per side - White reflector tape to EU spec at sides and rear, red at rear - Brackets for warning signs on left and right of swan neck and rear panel, including socket - ALU side boards and rear board on swan neck, removable, approx. 2,440 x 400 mm - Rear galvanised stake pockets are removable - 2 pairs WADER container pockets in loading area for 20ft container - 6 pairs stake pockets for removable stakes 100 x 50 mm in the outer frame - Adjustable hanging rail for ALU access ramps at the rear of the vehicle - Square climbing strips 20 x 20 mm every 200 mm on the outer frame of the loading area chamfer - Sand-finish anti-slip coating painted onto the tread plate on swan neck and loading area - Four warning boards extendable by approx. 400 mm, approx. 423 x 423 mm with position light - Bracket for beacon fitted to warning boards - 80 km/h speed sticker rear and on both sides - European reflective signs (Red-Yellow) at the rear of trailer - Manual and operating instructions on USB stick - HRM metallisation (High Resistance Metallisation) of the external frame - Complete steel structure shot-blasted, then specified visible surfaces metallised with ZINACOR 850 (Zinc 85% - Alu 15%) hot-finished

Stanje: novo, lastna masa: 12.800 kg, največja dovoljena obremenitev: 36.200 kg, skupna masa: 49.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 375 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 12.800 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimised loading platform length, approx. 3,750 mm in length - Gooseneck can be raised/lowered hydraulically and is detachable - Technical fifth wheel load: 25,000 kg - For tractor units: 4 x 2, 6 x 2, and 6 x 4 Loading platform: - Low-bed with external beams, designed as a telescopic vessel bridge in low-profile construction with front extension - Length 6,850 mm x width 2,540 mm - One locking position approx. every 1,000 mm on the extension Rear running gear: - Rear running gear with closed outer frame featuring checker plate cover and continuous prism excavator recess, approx. 1,250/700 x 505 mm, open at the rear Axles, suspension and tyres: - “PENDLE-AXLE”, all axles force-steered hydro-mechanically - Hose rupture valves on axle equalising cylinders with automatic reset function - Hydraulic cylinders with shut-off valves and pre-locking pins for securing in raised position - Final coat for axles with two layers of 2K acrylic paint, single-colour in “FAY-Grey-34-0260” - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres: 245/70 R 17.5 Bsdpfx Ajvy Edcsmtsli - TPMS tyre pressure monitoring system in accordance with ECE R 14 - TPMS sensors installed in all wheels, incl. spare wheels Included accessories: - Plug-in steel front wall, approx. 400 mm high - 3 kW electro-hydraulic unit for hydraulic operations, except for hydraulic winches - One spare wheel with mounting adapter - External beams of the gooseneck with mounting holes for bolt-on lashing rings - Plug-in ALU side walls on the gooseneck, approx. 400 mm high, anodised - One plug-in ALU rear wall on the gooseneck, approx. 400 mm high, anodised - Checker plate covering on the gooseneck - Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide - Operating area lighting at the gooseneck with on/off switch - Hydraulic traverse to support the gooseneck on the tractor or a dolly - 2" king pin - Anti-slip stickers on the left chamfer of the gooseneck - The rear upper area of the gooseneck is closed with a removable cover - 4 wheel chocks with holders - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of screw couplings - 1 pair of steel ramps with climbing strips and retaining bolts for bridging the low-bed mounting hooks - The ramps can be placed over or between the hooks - Mounting option for steel drive-on ramps at the rear between the external beams of the gooseneck - Prepared for bolt-on container locks for 1 x 20ft on the external beams - Mechanical pin and lug coupling from low-bed to running gear for exchanging the loading platform or inserting extension beams - With electro-pneumatic-hydraulic couplings - The outer beams of the low-bed are coated with painted-on sand layer as anti-slip protection - Removable (galvanised) load floor, can be inserted in 3 elements between the external beams, with hardwood surface - Foldable extensions, approx. 230 mm per side - Hanging strip at the front of the rear running gear to the low-bed for loose approach ramps - 2 pairs of stake pockets recessed into the outer frame of the running gear, for plug-in stakes approx. 100 x 50 mm - Hanging strip for loose ALU approach ramps at the rear cross member of the vehicle - Central lubrication system with 2 pumps - Radio and cable remote control - 4 extendable warning signs, approx. 423 mm x 423 mm - Numerous lashing positions

Stanje: novo, lastna masa: 15.900 kg, največja dovoljena obremenitev: 63.500 kg, skupna masa: 68.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 12.700 mm, širina tovornega prostora: 2.740 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75/r17,5, barva: siv, obratovalna teža: 52.100 kg, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimal load bed length, approx. 3,300 mm long, rear with taper approx. 1,000 mm x 10° Technical fifth wheel load: 23,000 kg For tractor units: 6x2, 6x4, and 8x4 Load bed: Extendable load bed, approx. 9,400 mm long with rear taper approx. 500 mm x 10° A recess in the load bed as well as in the tapering section for accommodating the excavator dipper stick, approx. 3,850 x 950 x 210/290 mm Pneumatic locking with conical locking bolt and reinforced locking positions, service lines are protected within the extendable beams and automatically adapt to the respective bed length Axles and Tires: BPW axles and suspension, 1st axle fixed, all other axles hydro-mechanically forced steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool 235/75 R 17.5 3PMSF twin tires Load index 143/141J (144/144F) Two-piece steel ramps: One pair of two-piece steel ramps, approx. 4,350 mm long and approx. 900 mm wide Hardwood covering Hydraulically folding ramp tips, each ramp hydraulically adjustable approx. 235 mm outward and approx. 215 mm inward Braking system: Braking system by WABCO EBS-E according to EU regulations Sockets and lighting: 24-volt lighting system Full metallization: Complete HRM metallization with ZINACOR 850 for optimal corrosion protection Surface treatment: Bjdemfqi Ijpfx Amteli Entire steel structure automatically blast cleaned with shot blasting after welding Second blasting treatment with corundum for optimal coating adhesion Final painting: 2 coats of 2-component paint in Novagrau, followed by sealing of cavities with special wax Rims in silver-grey Steel construction: Steel construction from high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Accessories: Plug-in steel front wall, approx. 400 mm high Connection rail for service lines to the tractor unit Spiral cable for supplying the electro-hydraulic unit and/or electric winch between trailer and tractor unit, with plug for the electro-hydraulic unit to control hydraulic operations, except for hydraulic winches Outer beam of gooseneck with mounting holes for bolted lashing rings First hole approx. 200 mm from the front, thereafter approx. every 400 mm One mounting hole in the rear upper area of the outer gooseneck beam for a bolted lashing ring Approx. 40 mm thick hardwood floor on the gooseneck, checker plate floor over the kingpin Guide plate on gooseneck for the fifth wheel plate, approx. 500 mm wide On the load bed, continuous and between the axles intermittent approx. 50 mm thick hardwood floor Load bed locking with conically welded locking profiles every 250 mm, including preload plate Slotted holes for attachable and movable bridging elements: on the fixed section behind the gooseneck at the front of the load bed 1 movable intermediate table for the extension tube with large cross-section Control valves for the hydraulic ramps on the right side of the vehicle Central lubrication system with 1 pump, standard grease according to NLGI-2 Radio remote control for steering operation, in addition to cable remote control, with 2 control lights on the receiver for single-track steering monitoring

Stanje: novo, lastna masa: 6.350 kg, največja dovoljena obremenitev: 38.650 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22,5, Oprema: ABS, Loading Platform: - 2 pairs of folding external lashing rings (LC 5,000 daN) Bodpfx Aeiu Etksmtjli - 24 pairs of cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) Landing Legs: - JOST mechanical landing legs with 2-speed gearbox, 24 t lifting capacity (50 t test load) Axles and Tyres: - BPW axles, air suspended, with disc brakes (430 mm), lift/lower function - Tyres: 385/65 R 22.5 Braking System: - WABCO braking system compliant with EU regulations featuring EBS-E (2S2M) Paintwork: - Premium and durable corrosion protection of the standard grit-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) top coat in single-tone MB 7350 Novagrau - Rear section metallized and painted in RAL 9010 (pure white) - Metallic paintwork not possible Steel Construction: - Steel construction made from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical System: - Electrical system in accordance with EU regulations - Lighting: 24 volt - ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connection bar with 24N, 24S, and 15-pin sockets - Connection standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Accessories included: - Yellow-red air couplings at the galvanized front connection bar - 4 wheel chocks with holders - 2" king pin - Galvanized steel front wall approx. 1,600 mm high, EN12642-XL - White reflector tape according to EU regulations, lateral and rear red - European reflective panels (red-yellow) at the rear of the trailer - Loading platform with approx. 30 mm thick hardwood flooring, framed in omega profiles - 10 pairs of stanchion sockets for 100 x 50 mm plug-in stakes in the outer frame - 3 pairs of transverse stanchion rack strips, fitted in the loading platform, for 100 x 50 mm plug-in stakes - Bracket for 1,000 mm plug-in stakes, rear in the central beam - 1 spare wheel carrier under the loading platform on the right hand side - 1 mudflap at the rear of the trailer - Manual and description on USB stick - Bracket for beacon at the rear of the trailer - Holders for warning signs including socket at the gooseneck and left/right rear panel - 6 pairs of WADER container locks on the loading platform for 1x 20ft, 2x 20ft, or 1x 40ft container, flush with rear - 80 km/h speed stickers at the rear and both sides - Four warning signs, extendable by approx. 400 mm, approx. 423 x 423 mm, with LED position light - Load gauge for axle load determination including load diagram - HRM (High Resistance Metallisation) of the outer frame - Complete steel structure is grit blasted, then defined visible surfaces are metallized with ZINACOR 850 (zinc 85% - aluminium 15%) by hot coating

Stanje: novo, lastna masa: 8.300 kg, največja dovoljena obremenitev: 36.700 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.080 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R 22.5, barva: siv, Oprema: ABS, dvižna zadnja plošča, Loading platform: Loading platform in extendable design with pneumatically operated locking mechanism Cutouts in the outer frame of the loading platform for attaching lashing straps Landing legs: JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity Axles and tires: BPW axles, air-suspended, with disc brakes (430 mm), with lift/lower function Trailing steering axle with electromagnetic reverse lock, activated via reverse gear or manually Axle tools Tires 385/65 R 22.5 Braking system: WABCO braking system in accordance with EU regulations with EBS-E Paintwork: Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer A high-quality single-color 2-component topcoat in MB 7350 Novagrau Rear section metallized and painted in RAL 9010 No metallic paint available Steel construction: Steel construction made of high-strength fine-grained steels Steel grades: S355J2+N / S355MC S690QL / S700MC Electrical system: Electrical system in accordance with EU regulations Bodpfxoikyh Ho Amtjli Lighting: 24 Volt ASPÖCK-NORDIK ASPÖCK-UNIBOX at the front connection bar with 24N, 24S and 15-pin sockets Connection according to ISO Accessories included: Front galvanized connection bar with yellow-red air couplings One galvanized steel front wall approx. 1,600 mm high, EN12642-XL 4 wheel chocks with holders White reflector tape according to EU regulations on the sides, on the extension, and in red at the rear European reflective plates at the rear of the trailer Loading platform with approx. 30 mm thick hardwood floor enclosed in omega profiles 10 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading platform 1 spare wheel holder under the loading platform, right-hand side in the direction of travel Manual and description One holder for a rotating beacon at the rear of the trailer On the gooseneck and each side of the rear plate (left and right), a bracket for warning panels incl. socket Anti-slip sand layer painted onto the central beam 6 pairs of WADER container pockets in the loading platform, for 1x 20ft container, 2x 20ft containers, or 1x 40ft container; the extension includes an additional locking point for one 45ft container 4 pairs of transverse stake pocket rails mounted in the loading platform for plug-in stakes 100 x 50 mm One galvanized holder transversely under the loading platform, 2,390 x 720 x 400 mm Access ladder mounted right-hand side in direction of travel Front axle lift axle with control via TEBS E depending on current axle load and load status Load manometer for determining axle loads, including load chart HRM metallization of the outer frame: complete steel structure shot-blasted, then the defined visible surfaces metallized hot-finished with ZINACOR 850

Stanje: novo, največja dovoljena obremenitev: 36.020 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 435/50 R 19.5, barva: siv, Oprema: ABS, Loading platform: - Loading platform in extendable design with pneumatically operated locking mechanism - 2 pairs of lashing rings (LC 5,000 daN) - 1 pair of lashing rings (LC 10,000 daN) - 6 pairs of fold-out lashing rings (LC 5,000 daN) - 2 pairs of fold-out lashing rings (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for attaching tension belts Bljdpei Dwlwefx Amtoi Axles and tires: - BPW axles, air-suspended, with disc brakes (377 mm), equipped with lifting/lowering function - Self-steering axles with electromagnetically controlled reverse lock, activated via reverse gear or manually - Axle tools - Tires: 435/50 R 19.5 Brake system: - Brake system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - Premium, durable corrosion protection for the standard shot-blasted welded frame by means of two-component (2K) zinc dust primer - High-quality two-component (2K) top coat in solid Novagrau - Rear end metallized and painted in RAL 9010 (pure white) - Metallic paint not available Landing gear: - JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Steel construction: - Steel structure made of high-strength fine-grained steels. - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDICK (ASS3) lighting - ASPÖCK-UNIBOX on the front connection console with 24N, 24S & 15-pin sockets - Connections according to ISO standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Accessories included: - Yellow-red air couplings at the galvanized front connection strip - 2 wheel chocks with holder - 2" kingpin - A galvanized steel front wall approx. 1,600 mm high - Yellow reflective tape as per EU regulations, on the sides, on the extension and at the rear of the trailer - European reflective signs (red-yellow) at the rear of the trailer - Loading area with approx. 38 mm thick hardwood floor - 10 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame of the platform - 1 spare wheel holder beneath the loading area on the right in the direction of travel - User manual and documentation on USB stick - One mudflap at the rear of the trailer - Bracket for a revolving beacon at the rear of the trailer - On the gooseneck and on the rear panel, left and right, each a bracket for warning boards including socket - One INOX toolbox transversely mounted beneath the platform (1,000x400x2,500mm) - 6 pairs of WADER container locks in the platform for 1x 20ft container, 2x 20ft containers or 1x 40ft container; an additional locking point is provided in the extension for a 45ft container - 3 sets of crosswise post pocket bars mounted in the platform for 100 x 50 mm plug-in posts - 60 km/h speed sticker on the rear - 2 reversing spotlights mounted on the rear panel - Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light - Mounting bracket for rotating beacon on the warning sign - HRM metallization (High Resistance Metallisation) of the outer frame - Entire steel structure shot-blasted, the defined visible surfaces then hot-finished with ZINACOR 850 metallisation (zinc 85% - aluminum 15%)

Stanje: novo, največja dovoljena obremenitev: 40.320 kg, skupna masa: 50.960 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Selection of equipment. Complete specification available on request. Gooseneck: * Gooseneck with rear bevel approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick. Loading area with 5 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Landing Gear: JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Tyres: * 205/65 R17.5 tyres – manufacturer of our choice TPMS: * TPMS tyre pressure monitoring system in accordance with ECE R 141 Axles: * BPW axles, two rigid and two self-steering axles * Air suspension with lift/lower function * Drum brakes * Self-steering axles with electromagnetic reversing lock, activated via reverse gear or manually Brake system: * WABCO brake system compliant with EU regulations and EBS-E (4S3M) Electrical system: * Electrical system according to EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with indicator * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: * Steel structure made of high-strength fine grain steel * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) for optimal corrosion protection * Trailer colour RAL 3002 Carmine Red * Rims Silver Grey * Tarp RAL 9006 (brilliant direct) Options included: * At the gooseneck and at the rear, left and right, one bracket each for warning signs, including socket * 2-inch king pin * One galvanized steel front wall * Yellow-red air couplings at the galvanized front connection strip * 4 wheel chocks with holder on the front wall * 3 tiers of wooden boards Bodpfx Amsy Aug Djtjli * Galvanized folding supports under the loading area bevel * One bracket for a revolving warning light at the rear end of the trailer * Height-adjustable curtain structure – approx. 3,960 mm? * Galvanized front wall with tensioning mechanism for sliding curtains. Height adjustable by approx. 400 mm * Roof brand EDSCHA, can be slid forward on ALU roof profile beams (bolted to front and rear wall) * 3 pairs of movable stanchions in the loading area * Body hydraulically extendable to the left and right at the rear by approx. 750 mm * Sliding roof with fold-up portal beam * Sliding tarp with 700 mm reserve in length; tie-down straps at approx. 600 mm intervals. Height upper edge of body approx. 3,960 mm (loaded) * Driving with the sliding roof open is not permitted and will damage the tarp * Body at the rear closed with anodized ALU swing doors * Latch-on rail for ALU loading ramps at the rear of the vehicle * Control valves for hydraulic widening fitted to the right-hand side of the trailer * White reflective tape as per EU regulations on the sides, red at the rear * Electro-hydraulic unit under the rear loading area * One mudguard at the rear of the trailer * European reflective signs (red-yellow) at the rear of the trailer * Hand…

Stanje: novo, največja dovoljena obremenitev: 36.410 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete vehicle inventory, including vehicles available immediately or at short notice, can be found on our website. Excerpt from the equipment. Full equipment details available on request. GOOSENECK: * Gooseneck in SNT design to optimize load bed length, approx. 3,700 mm long, with rear taper approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Steel front bulkhead, removable, approx. 400 mm high * ASPÖCK-UNIBOX * 3 kW electric-hydraulic unit for hydraulic operations, excluding hydraulic winches * Approx. 40 mm thick hardwood cover above the gooseneck * 2-inch kingpin * Guide plate from the gooseneck for the fifth-wheel plate, approx. 500 mm wide Blsdey Auh Ispfx Amtoi * Receptacle at the rear of the gooseneck for aluminum drive-on ramps * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 4 wheel chocks with holders in front of the bulkhead * 1 pair of stake pockets embedded in the gooseneck, for plug-in stakes approx. 100 x 50 mm (inner chassis rail) EQUIPMENT: * Load bed approx. 8,800 mm long, extendable version approx. 4,100 mm, with rear taper approx. 500 mm x 10° * Recess in the load bed including the rear slope to accommodate the excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * Pneumatic locking with conical locking bolts and reinforced locking positions, with protected supply lines inside the extendable beams, automatically adapting to the respective load bed length * TPMS tire pressure monitoring system according to ECE R 141 * BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle steering-following * 3rd axle with electromagnetic reverse lock, activating via reverse gear or manually * Technical axle load: 12,000 kg each, air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires. Make at our discretion * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B - static test load = approx. 50,000 kg * Continuous and between-axle interrupted approx. 50 mm hardwood planking on load bed (increasing coefficient of friction) * 1 cross table, approx. 300 mm wide, for the extendable tube with large cross-section; cross table with offset load bed and extendable mounting rails for aluminum bridging elements * Load bed locking with conically welded locking profiles every approx. 250 mm, including pretensioning plate * 1 pair of lashing rings on front crossbeam (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the load bed, foldable outwards (LC 10,000 daN) * 1 pair of fixed wheel recesses in front of the axles, open up to the gooseneck crossbeam, approx. 700 x 410 mm (W x D) * Wheel recesses with approx. 15 x 15 mm square climbing strips and widened sections at the lower area (if vehicle is fitted with extendable widenings) * 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the load bed between 1st and 2nd axle * Wheel recesses with approx. 15 x 15 mm square climbing strips and widenings in lower area * Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axle, can also be used as widening planks (if vehicle is fitted with extendable widenings) * Aluminum elements lockable on the extension beams of the widenings * 1 pair of mechanical rear supports * 1st axle with traction aid * Sandblasted and painted in single color according to RAL code

Stanje: novo, največja dovoljena obremenitev: 36.020 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete inventory of vehicles available for immediate or short-term delivery on our website. Partial equipment listing. Full equipment details available upon request. Bljdey Auhujpfx Amtei Gooseneck: * Gooseneck with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area with rear bevel approx. 1,000 mm x 8° * 5 pairs of outward folding lashing rings (LC 5,000 daN) * 3 pairs of outward folding lashing rings (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) * Hardwood flooring approx. 48 mm thick, with checker plate covering over the axles Two-part steel ramps: * One pair of galvanized two-piece steel ramps, approx. 3,185 + 1,420 x 1,250 mm, with grating surface C40/5 (point load approx. 2.8 t on an area of approx. 20 x 20 cm) * Ramp with hydraulically folding ramp sections and hydraulic lifting mechanism * Maximum load per pair: 30,000 kg Landing legs: * JOST landing gears (manual) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, can be activated via reverse gear and manually * Air suspension with raise and lower valve Tyres: * 235/75 R 17.5 3PMSF tyres – manufacturer at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Brake system: * WABCO brake system compliant with EU regulations with EBS-E (2S2M) without connectors to the tractor unit Steel structure: * Steel construction made from high-tensile fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system in accordance with EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX at the front connector strip with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * HRM metalizing of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for optimal corrosion protection * Final coating with 2 layers of two-component topcoat, single colour in RAL 3002 carmine red, in accordance with RAL System 841GL * Rear section metalized and painted RAL 9010 (Pure White) * Wheels in silver Including accessories: * One bracket for warning signs on both sides at the gooseneck and at the rear, including socket * 1 spare wheel holder under the loading area on the right-hand side * 2" kingpin * Galvanized steel front wall * Yellow-red air couplings on the galvanized connector strip at the front * 4 wheel chocks with holders on the front wall * 3 height-adjustable wooden planks * Galvanized folding supports under the loading area bevel * Bracket for a rotating beacon at the rear of the trailer * Height-adjustable tarpaulin frame (approx. 3,960 mm) * Galvanized front wall with tensioning mechanism for sliding curtains, height-adjustable by approx. 400 mm * EDSCHA roof, forward-sliding, on aluminium roof beam profiles (bolted with front and rear wall) * 3 pairs of sliding stakes in the loading area * Superstructure can be hydraulically widened at the rear to left and right by approx. 750 mm * Sliding roof with liftable portal carrier * Sliding tarpaulin with approx. 700 mm slack in length, with tensioning straps spaced approx. 600 mm

Stanje: novo, največja dovoljena obremenitev: 37.980 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: * Gooseneck with approx. 45° beveled front corners and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approx. 30 mm thick Loading platform (extendable version): * Extendable loading platform with rear chamfer approx. 1,000 mm x 8° * 6 pairs of folding-out lashing rings (LC 5,000 daN) * 3 pairs of folding-out lashing rings (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front of the loading platform (LC 10,000 daN) * Cut-outs in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) * Hardwood flooring, approx. 48 mm thick, with checker plate over the axles Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lift capacity (approx. 50 t static load) Tyres: * 235/75 R 17.5 3PMSF tyres – manufacturer at our discretion TPMS: * TPMS tyre pressure monitoring system in accordance with ECE R 141. Data transmission to the tractor unit is via the standardised EBS interface per ISO 11992. For correct display, the tractor unit must be able to transmit and display these data. Axles: * BPW axles and suspension, 2 rigid axles, 1 steering trailing axle * Technical axle load: 12,000 kg each * Electromagnetic reversing lock activated by reverse gear and manually * Air suspension with lift/lower valve * Axle tools Brake system: * Brake system compliant with EU regulations with EBS-E (2S2M), no connecting lines to the tractor unit Steel construction: * Steel construction made from high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: * Complete steel structure automatically shot-blasted after welding with blast wheel machine * Secondary blasting with corundum for optimal coating adhesion * Final painting with 2 layers of 2K topcoat, single colour RAL 3002 Carmine Red as per RAL System 841GL * Rims in silver-grey * Rear section metallized and painted in RAL 9010 (pure white) * Paint system tested in salt spray test per ISO 9227-NSS Bodpfxjy Aufme Amtsli * Cavity sealing with special wax Electrical system: * Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights synchronized with the indicator * ASPÖCK-UNIBOX at the front connector rail with sockets: 24N, 24S, & 15-pin according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Accessories included: * 2-inch king pin * One galvanized steel front wall, approx. 400 mm high * One spare wheel carrier in front of the front wall * Yellow-red air couplings on the galvanized front connection rail * 4 chock blocks with holder at the front wall * Mount at the rear of the gooseneck for ALU approach ramps * Galvanized folding supports under the loading platform rear chamfer * At the gooseneck and on the rear panel, left and right, each with a bracket for warning signs including socket * Load gauge for determining axle loads with load diagram * On the gooseneck, plug-in aluminium side and rear walls, approx. 2,440 x 400 mm (L x H). The rear galvanized plug-in stanchions are removable. (Superstructure length approx. 2,560 mm) * One galvanized toolbox integrated in the beveled gooseneck * 3 pairs WADER C

Stanje: dober (rabljeno), številka stroja/vozila: YAFTL6002R0035345, dolžina tovornega prostora: 14.800 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 9.000 mm, Leto izdelave: 2024, = Dodatne možnosti in oprema = Blodpfx Amjx Rtiastsi - Zračno vzmetenje zadaj - Zračno vzmetenje spredaj - Bobnasti zavorni sistem = Dodatne informacije = Nosilnost: 81.100 kg Skupna dovoljena masa: 81.100 kg Tehnično stanje: dobro Vizualno stanje: dobro Stanje sprednjih pnevmatik: 60 Sprednje pnevmatike: 245/70 R17.5 Zadnje pnevmatike: 245/70 R17.5 Zadnji pregled: 28.12.2025 Za več informacij kontaktirajte Lastas Sales.

Stanje: zelo dobro (rabljeno), prva registracija: 09/2015, dolžina tovornega prostora: 20.180 mm, širina tovornega prostora: 3.000 mm, barva: drugo, Leto izdelave: 2015, Damage: none YAFTL2007F0017329 = Further Information = Unladen weight: 13,600 kg Payload: 28,400 kg Gross vehicle weight: 42,000 kg Technical condition: very good Visual condition: very good Price: On request Registration number: DW205AH = Company Information = If you have any questions or suggestions, don't hesitate to contact us. We guarantee a response within 8 hours. Prices are exclusive of VAT. No rights can be derived from the information provided. Bodpsymrb Sefx Amtsli Office Phone: MOB: Dutch - English - German - French - Spanish - Italian (Available on WhatsApp and Viber.) MOB: Dutch (Available on WhatsApp and Viber.) When making a payment by bank transfer, the funds must be transferred to our bank account listed below. Always check the payment details stated on our website. If you have received different information, please contact us. If you have any doubts, please call us so we can verify the invoice and/or payment. Bank details: Rabobank Laan van Limburg 2 4701BP Roosendaal IBAN: NL 89 RABO EORI/VAT/TAX: NL857401B(01) BIC/SWIFT: RABONL2U

Stanje: novo, skupna masa: 78.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 850 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck in SNT design to optimize loading area length, approx. 3,700 mm long, rear with a bevel approx. 1,000 mm x 10° • For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading Area: • Extendable loading platform, approx. 8,800 mm long with rear bevel approx. 500 mm x 10° • A recess in the platform and rear bevel to accommodate the excavator dipper stick, approx. 3,950 x 580 x 370/450 mm Ramps: • One pair of two-piece steel ramps, approx. 4,350 mm long and 900 mm wide • Hydraulically folding ramp tips • Ramps hydraulically adjustable separately approx. 235 mm outwards and approx. 215 mm inwards • Hardwood decking on the beveled part of the loading area • Ramp with hardwood decking • 20 x 30 mm square climbing strips, approx. every 200 mm on the outer frame of the ramp Axles and Tyres: • TWINAXLE-II independent wheel suspension with BPW stub axles, 1st axle steered in advance, all other axles are hydromechanically forced steered • 1st axle with electromagnetic reverse lock via reverse gear and manual activation • Technical axle load: 12,000 kg • Hydr. axle compensation, hydraulic cylinders with shut-off valves • Tyres 245/70 R 17.5 Bedpjrvw U Ssfx Amteli • TPMS tyre pressure monitoring system according to ECE R 141 Accessories Included: • Plug-in steel front wall, approx. 400 mm high • 4 wheel chocks with holder • Front connection bar with yellow-red air couplings • 3 kW electro-hydraulic power pack for hydraulic control, except for hydraulic winches • 1 spare wheel • 2 pairs of screw-in lashing rings • 1 pair of horizontal lashing rings in the rear area of the gooseneck • On the gooseneck: 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized • On the gooseneck: 1 plug-in ALU rear board, approx. 400 mm high, anodized • Approx. 40 mm thick hardwood decking on the gooseneck, checker plate over the king pin • 3.5" king pin • Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide • Load area locking with conically welded arresting profiles every 250 mm • Incl. pre-tensioning plate • 1 pair of lashing rings on the front cross member • 8 pairs of recessed, fold-out lashing rings in the outer frame of the platform • Extendable (galvanized) widenings approx. 230 mm per side • 1 pair of fixed open wheel recesses up to extension, approx. 700 x 410 mm, in the platform in front of the 1st axle • Wheel recesses with checker plate covering and 15 x 15 mm square climbing strips, approx. every 200 mm • 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm, in the platform between the 1st and 2nd axle • Wheel recesses with 15 x 15 mm square climbing strips and widenings in the lower section • ALU covers for the wheel recesses between 1st and 2nd axle, which can also be used as broadening planks • 1 pair of mechanical rear supports • 20 x 30 mm square climbing strips, approx. every 200 mm on the outer frame of the bevel of the loading area • Central lubrication system with 1 pump, BEKAMAX brand, standard grease as per NLGI-2 • Radio and cable remote control, with 2 indicator lights on the receiver for single wheel control • WABCO Smart Board system • The Smart Board is equipped with an odometer • 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and mounts for rotating beacon

Stanje: novo, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.700 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 890 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimizing loading area length, approx. 3,700 mm long, with rear tapering of approx. 1,000 mm x 6° - For tractor units: 4 x 2 and 6 x 2 Loading platform: - Loading platform, approx. 9,700 mm long, with hydraulically foldable and lowerable rear section as well as hydraulically liftable front section for driving onto the gooseneck Axles and tyres: - BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle self-steering - 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually - Technical axle load: 12,000 kg - Air suspension with lift/lower valve - 235/75 R 17.5 3PMSF twin tyres - TPMS tyre pressure monitoring system according to ECE R 141 BPW Auto Reverse Control: - Electrohydraulic auxiliary steering for the self-steering axle of a 3-axle unit - Automatic control of the self-steering axle when reversing via gyroscope sensor - Manual steering operation in forward and reverse using separate radio remote control - Manual operation enabled up to 10 km/h - System powered by separate electro-hydraulic unit Accessories included: - Removable steel front wall, approx. 400 mm high - 3 kW electro-hydraulic power pack - External beams on gooseneck with mounting holes for bolted lashing rings - First mounting hole approx. 200 mm from front, then approx. every 400 mm - One mounting hole at upper rear of external gooseneck beams for a bolted lashing ring - Grating cover with 5 mm sheet reinforcement on gooseneck and rear taper - 2" king pin - Guide plate on gooseneck for fifth wheel plate, approx. 500 mm wide - Round NATO socket at front connection bar (Maeler & Kaege VG 96 917) - 1 pair of removable side aluminium drop sides on gooseneck, approx. 400 mm high, anodized - 4 wheel chocks - Electric winch, approx. 5,400 kg pulling force, with radio remote control Bodjyw Sakspfx Amtoli - Wire cable approx. 24 m long, cable ø approx. 9.5 mm, including cable pressure roller - Winch installed at the front inside the gooseneck - Continuous grating cover with 5 mm steel underlay for additional reinforcement, designed for point loads: - on the lift bed - on the loading platform - on the hydraulically lowerable rear section - Painted-on sand coating on the gooseneck covering plates and in transition areas between neck and lift bed, between lift bed and loading platform, and between loading platform and ramps - 1 spare wheel - Hydraulic lift bed, approx. 2,500 mm long, load capacity while driving in raised position: 9,000 kg - Hydraulic cylinders are fitted with load-holding valves - Cut-outs in the outer frame of the loading platform and lift bed for attaching tension straps - Extensive lashing positions - Hydraulically lowerable rear section for loading and unloading, can be raised to shorten total coupling length - Load capacity while driving in horizontal position: 10,000 kg - Shortening of total coupling length when raised: 2,350 mm - Painted-on sand coating on the complete ramp, except for the extendable galvanized part of the ramp - Hydraulically extendable rear extensions for loading and unloading - Radio remote control: - Control of hydraulic lift bed - Control of hydraulic lifting of rear extension - Control of hydraulic extension of rear extension - 1st axle with starting aid - Centralized lubrication system with 1 pump - 4 warning signs, approx. 423 x 423 mm, extendable

Stanje: novo, največja dovoljena obremenitev: 47.300 kg, skupna masa: 58.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.600 mm, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment list. Complete equipment details available upon request. Gooseneck: * Gooseneck with chamfered front corners approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area in extendable design with rear chamfer approx. 1,000 mm x 8° * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN) * 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) * Recesses in the outer frame of the loading area for securing straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate flooring above the axles Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Tyres: * Tyres 235/75 R 17.5 3PMSF, manufacturer of our choice Axles: * BPW axles, two rigid axles, two self-tracking axles, air suspension, drum brake, with lifting/lowering function * The self-tracking axles can be locked for reversing by electro-magnetic reverse lock via reverse gear or manually * Axle tools Brake system: * WABCO brake system in compliance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system: * Electrical system in accordance with EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting * ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Premium and durable corrosion protection for the standard shot-blasted welded frame ensured by a two-component (2K) zinc dust primer * High-quality two-component (2K) topcoat, single colour, RAL 3002 Carmine Red * Rear section metallised and painted in RAL 9010 (Pure White) * Rims in silver Accessories: * Spare wheel holder in front of the front wall (without spare wheel) * 2-inch king pin * Galvanised steel front wall approx. 400 mm high * Yellow-red air couplings on the galvanised connection strip at the front * Mount in the rear area of the gooseneck for ALU loading ramps * Galvanised folding supports under the rear chamfer of the loading area Bedpfxeyvnfgj Amteli * Holder for a beacon at the rear of the trailer * On the gooseneck and at the rear end panel, left and right, holders for warning signs including socket * TPMS tyre pressure monitoring system according to ECE R 141 * On the gooseneck, plug-in aluminium side walls and tailgate, approx. 2,440 x 400 mm (L x H). The rear galvanised plug-in stanchions are removable. (Body length approx. 2,560 mm) * Galvanised toolbox integrated into the chamfered gooseneck * 3 pairs of WADER container pockets recesses in the loading area for a 20' (30') or 40' container * Sliding hooks for aluminium loading ramps at the rear of the vehicle * 6 pairs of stanchion pockets for plug-in stanchions approx. 100 x 50 mm in the outer frame of the loading area * Galvanised extensions, extendable by approx. 230 mm per side * Lift axle on the front axle with control via TEBS E depending on the current axle load and current loading status * 2 LED reversing lights mounted on the rear end panel * 2 pairs Ferry-

Stanje: rabljeno, največja dovoljena obremenitev: 44.420 kg, skupna masa: 53.000 kg, konfiguracija osi: 3 osi, prva registracija: 04/2025, naslednji pregled (TÜV): 04/2026, dolžina tovornega prostora: 11.500 mm, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete range of immediately and soon available vehicles on our website. Excerpt from the equipment. Complete equipment details on request. Loading platform: * Loading bed with approx. 30 mm thick hardwood floor * 9 pairs of folding lashing rings towards the outside (LC 10,000 daN) * 10 pairs of stake pockets in the outer frame of the loading platform for plug-in stakes approx. 100 x 50 mm Landing gear / Support legs: * Hydraulic landing gear Tyres: * Tyres 385/65 R 22.5 - MICHELIN MULTI High Load 164K Bedpfjyu Eu Ijx Amtoli TPMS: * TPMS tyre pressure monitoring system according to ECE R 141. Data transmission to the truck is carried out via the standardised EBS interface according to ISO 11992. For correct display, the truck must be capable of transmitting and displaying this data. Axles and suspension: * BPW axles, technical capacity 10,000 kg each, first axle hydro-mechanically steered, second axle fixed, and third axle hydro-mechanically forced-steered, mounted on turntable * Air suspension with raise/lower valve Brake system: * WABCO brake system according to EU regulations with EBS-E (4S3M), without connecting lines to the tractor unit Electrical system: * Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front connection rail with sockets 24N, 24S & 15-pin connectors according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Coating: * Entire steel construction shot-blasted automatically after welding using a turbine blast machine * Second blasting treatment with corundum for optimal adhesion of the coating system * HRM metallisation of the entire chassis with ZINACOR 850 (85% zinc/15% aluminum) for maximum corrosion protection * Final coating with 2 layers of 2K topcoat, single color in RAL 9005 Jet Black as per RAL System 841GL * Rear section metallised and painted in RAL 9010 (Pure White) * Rims in silver grey * Coating tested by salt spray test according to ISO 9227-NSS * Cavities sealed with special wax Included accessories: * Loading platform with approx. 30 mm thick hardwood floor * 2-inch king pin * One galvanized steel front wall (EN12642-XL), approx. 1,200 mm high * DUOMATIK air couplings at the galvanized connection rail at the front * Storage for approx. 1,000 mm plug-in stakes, rear in the central beam * On the gooseneck and on the rear panel left and right, each with a bracket for warning panels including socket * White reflective tape in accordance with EU regulations on the sides and red at the rear * 10 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading platform * European reflective plates (red-yellow) at the rear of the trailer * One holder for a rotating beacon at the rear of the trailer * One mud flap at the rear of the trailer * Manual and description on USB stick * BEKAMAX central lubrication system (Pico) with standard grease NLGI-2 and removable pump cover * 4 wheel chocks with holder on the front wall * Steering from the front and rear via cable remote control with push buttons, with axle tracking control (without installation in the tractor unit) * Electro-hydraulic unit * 6 pairs of galvanized plug-in stakes, approx. 100 x 50 mm, approx. 1,000 mm high * 5 pairs of crosswise stake pocket bars mounted in the loading plat

Stanje: novo, skupna masa: 80.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Further vehicles available – excerpt from the equipment list. Full equipment details on request. GOOSENECK: * Gooseneck in SNT design for optimized loading bed length, length approx. 3,700 mm, rear with chamfer approx. 1,000 mm x 10° * For tractor units: 4x2, 6x2, and 6x4 * Front steel bulkhead, plug-in, approx. 400 mm high * ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for controlling hydraulic functions (excluding hydraulic winches) * Outer beams of the gooseneck with mounting holes for bolted lashing rings. First hole approx. 200 mm from the front, then approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair horizontal lashing rings at the rear section of the gooseneck (LC 10,000 daN) * On the gooseneck: 1 pair removable ALU side boards approx. 400 mm high, anodized finish * On the gooseneck: 1 removable ALU rear board approx. 400 mm high, anodized finish * Over the gooseneck: approx. 40 mm hardwood flooring, over the king pin checker plate covering * 3.5-inch king pin * Gooseneck guide plate for the fifth-wheel plate, approx. 500 mm wide * Round NATO socket at the front connection bar (Maeler & Kaege VG 96 917) * 2 pairs of suspended lashing rings with retaining spring on the outer beams of the gooseneck (LC 5,000 daN) LOADING BED: * Loading bed, extendable version, length approx. 8,800 mm with chamfer at the rear approx. 500 mm x 10° * Pneumatic locking with conical locking bolt and reinforced locking positions, supply lines are protected within the extendable beams and automatically adapt to the respective bed length * BPW axles and suspension, first axle hydraulically steered, all other axles hydro-mechanically forced steered * First axle with electro-magnetic reverse lock, activated by reverse gear and manually * Technical axle load: 12,000 kg each Bedpfxoxarmae Amteli * Air suspension with lifting and lowering valve * 235/75 R 17.5 3PMSF twin tyres – manufacturer at our discretion * Mechanical landing legs with 2-speed gearbox and crank. JOST Modul B – static test load = 50,000 kg * Continuous hardwood flooring (approx. 50 mm thick) on the bed and between axles (interrupted), increasing friction coefficient. – Slots for attachable and adjustable bridging elements * At the front of the bed – 1 movable intermediate table approx. 300 mm wide for the large-section telescopic tube, with checker plate covering. – Front and rear slots for attachable and adjustable bridging elements * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 7 pairs of recessed folding lashing rings on the outer frame of the bed (LC 10,000 daN) * Extensions (galvanized), extendable by approx. 230 mm per side (without wooden planks) * 1 pair mechanical rear supports * Remote-controlled steering from front and rear via cable remote control, with single-track control of axles, without installation in the tractor unit * TPMS tire pressure monitoring sensors installed in all wheels * Locking of the bed with conically welded retaining profiles every 500 mm * Locking control left and right on the trailer * For the intermediate table approx. 300 mm wide, a mechanical lock for securing the table in the extension * 5 pairs of threaded blocks on the extendable beam for mounting M20 screw rings (LC 5,000 daN) BRAKING SYSTEM

Stanje: novo, največja dovoljena obremenitev: 90.700 kg, skupna masa: 126.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.850 mm, Oprema: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: Hydraulically lift/lower and detachable gooseneck. Length approx. 3,650 mm. Suitable for tractor units: 6x4 or 8x4 3-axle compact front bogie: * Hook mounts at front and rear. Length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Lowbed: * ATX-A lowbed with telescopic longitudinal beams in low-profile design, fixed hardwood floor approx. 50 mm thick * With drive-over bridge hooks at the front and bolt-lug coupling at the rear * Base width: approx. 2,850 mm, length: approx. 7,150 mm, beam height: approx. 330 mm, beam width: approx. 750 mm * Loading height approx. 480 mm, ground clearance approx. 150 mm 5-axle rear bogie: * Mechanical bolt-lug coupling for attaching a lowbed at the front; rear end traverse * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * Pendulum axle 3-axle front bogie: * PENDULUM AXLES, all axles hydro-mechanically forced-steered * Hose rupture valve on axle leveling cylinder with automatic RESET function * Hydraulic cylinders with shutoff taps and locking pins for securing in raised position * Final painting of axles with 2 coats of single color 2K paint, painted in MB7350 Novagrau * Rated axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tires for front bogie: 12 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J 5-axle rear bogie: * PENDULUM AXLES, all axles hydro-mechanically forced-steered * Hose rupture valve on axle leveling cylinder with automatic RESET function * Hydraulic cylinders with shutoff taps and locking pins for securing in raised position * Final painting of axles with 2 coats of single color 2K paint, painted in MB7350 Novagrau * Rated axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tires for rear bogie: 20 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimum corrosion protection Bedpfxow Tgp Ds Amtsli * Final painting with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, according to RAL-System 841GL Including accessories: * Steel front wall, approx. 400 mm high * Plug-in aluminum side and rear boards on gooseneck, approx. 400 mm high, anodized * 3.5" kingpin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections on gooseneck * Front bogie with separate air connection for air impact wrench * BEKA-MAX central lubrication for one 3-axle bogie * Preparation for bolt-on container positioning for 1 x 20' or 1 x 30' on the outer beams * Without container locks * Brackets on the outer beams for installing foldable extensions * One 7-pin socket left and right, front and rear on rear bogie for warning panels * BEKA-MAX central lubrication for one 5-axle bogie * On the rear bogie, socket for cable remote control for steering * Rear bogie with trough * 2 LED reversing lights mounted on rear panel * European reflector boards (red-yellow) on the rear * One mudflap at rear * One LED beacon with bracket left and right on rear cross-member * Two INOX toolboxes 855 x 340 x 390 mm on gooseneck, left and right * 1-circuit...

Stanje: novo, lastna masa: 14.800 kg, največja dovoljena obremenitev: 61.700 kg, skupna masa: 76.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck with rear chamfer of approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Loading Platform: • Extendable loading platform with rear chamfer of approx. 500 mm x 8° • 9 pairs of folding external lashing rings • 1 pair of recessed lashing rings at the front of the loading platform • Cutouts in the outer frame of the loading platform for attaching tension belts • Approx. 48 mm thick hardwood flooring, checker plate above the axles Landing Legs: • JOST mechanically operated landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: • BPW axles and suspension, 1st axle steering, 2nd and 3rd axle fixed, 4th and 5th axle follow-steering • Technical axle load: 12,000 kg • 1st, 4th, and 5th axles with electromagnetic reverse lock, activated via reverse gear or manually Bodema Hf Repfx Amtoli • Tyres: 235/75 R 17.5 3PMSF Brake System: • WABCO brake system in accordance with EU regulations including EBS-E (4S3M) Paintwork: • Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer • High-quality single-color two-component (2K) topcoat in MB 7350 Novagrau • Rear section metallized and painted in RAL 9010 (Pure White) Steel Construction: • Steel structure made from high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC (yield strength 355MPa) • S690QL/S700MC (yield strength 690MPa) Accessories: • One spare wheel with holder in front of the front wall • 2" king pin • Galvanized steel front wall, approx. 400 mm high • Front galvanized connection strip with yellow-red air couplings • 2 wheel chocks with holders mounted on the front wall • Rear mount on gooseneck for ALU drive-on ramps • Galvanized extendable wideners appx. 230 mm per side • Bracket for a beacon at the rear of the trailer • Galvanized supports under the chamfer of the loading platform • White reflector tape on the sides as per EU regulations, red at the extension and rear • Mounts for warning panels including socket left and right at the gooseneck and rear panel • Detachable ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • Rear galvanized plug-in stanchions removable (body length approx. 2,560 mm) • 3 pairs of WADER container pockets in the loading platform for a 20ft (30ft) or a 40ft container • 7 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform • Lifting axle on the front axle with TEBS E control according to the current axle load and loading condition • Movable mounting rails for ALU drive-on ramps at the rear of the vehicle • 20 x 20 mm square climbing strips at 200 mm intervals on the outer frame chamfer of the loading platform • BEKAMAX (Pico) centralized lubrication system with NLGI-2 standard grease and removable pump cover • Four extendable warning panels approx. 423 x 423 mm with a position light, extendable by approx. 400 mm • Holder for beacon mounted on the warning panels • European reflector plates (red-yellow) on the rear of the trailer • 80 km/h speed limit stickers at rear and both sides • Axle load gauge with load diagram included • HRM Metallisation (High Resistance Metallisation) of the outer frame • Complete steel structure is shot-blasted, then defined visible surfaces are metallized with ZINACOR 850 (zinc 85% - aluminum 15%) using hot finishing

Stanje: novo, največja dovoljena obremenitev: 37.075 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our full stock of immediately and soon-available vehicles on our website. Selected features listed below. Complete specification available upon request. Gooseneck: * Gooseneck with beveled front corners approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring approx. 30 mm thick Load area: * Load area hydraulically raisable and lowerable after the gooseneck, length approx. 2,800 mm, with rear chamfer approx. 1,000 mm x 8° Bledsyhkqzjpfx Amtoi * 6 pairs of outward-folding lashing rings (LC 5,000 daN) * 2 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of inward-folding lashing rings on the front central beam (LC 10,000 daN) * Cutouts in the external frame of the loading area for attaching tensioning straps (LC 2,000 daN) * Grating surface C40/4 (point load approx. 2.3 t on an area of approx. 20 x 20 cm), checkered plate surface above the axles Two-part steel ramps: * One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with grating surface C40/4 (point load approx. 2.2 t on an area of approx. 20 x 20 cm) * Ramp with hydraulically foldable ramp sections. Hydraulic lifting system, hydraulically extendable * Maximum load capacity per pair: approx. 40,000 kg Landing legs: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 steering trailing axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lockout, activated by reverse gear and manually * Air suspension with lift and lower valve Brake system: * WABCO brake system in accordance with EU regulations with EBS-E (2S2M) Tyres: * 235/75 R 17.5 3PMSF – Brand of our choice TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Paintwork: * HRM metallization of the complete vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimal corrosion protection * Final coating with two layers of 2K topcoat, single color in RAL 3002 Carmine Red according to RAL system 841GL * Wheels in silver-grey Included equipment: * 2" kingpin * One galvanized steel front wall, approx. 400 mm high * Grating surface in the gooseneck’s chamfer C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * Grating surface in the load area’s chamfer C40/4 (point load approx. 3.4 t on an area of approx. 20 x 20 cm) * Sand coating applied as slip protection to the checkered plates above the kingpin and loading area * Electro-hydraulic power unit under the rear of the load area * On the gooseneck: removable aluminum side and rear walls, approx. 2,440 x 400 mm (L x H). The galvanized rear stakes are removable. (Body length approx. 2,560 mm) * One electric cable winch with radio remote control, approx. 5,400 kg line pull, incl. approx. 9.5 mm steel cable, approx. 24 m long, with cable guide roller * Bolted 5 t ring for guiding the winch cable on the neck without a deflection roller * One galvanized toolbox integrated into the chamfered gooseneck, with opening for winch * Grating surface on gooseneck C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * 7 pairs of stake pockets for approx. 100 x 50 mm slip-in stakes in the outer frame of the loading area * Lift axle on the front axle, controlled by TEBS E depending on current axle load and loading condition * 7 pairs of... [Text truncated - please provide remaining content for further translation if needed.]