Polpriklopnik z nizkim ležiščem za prevoz gradbenih strojev

Faymonville 4-1+3-A-Semi-Twinaxle II-Rampen-MultiMAX

Gooseneck:
• Gooseneck in SNT design to optimize loading area length, approx. 3,700 mm long, rear with a bevel approx. 1,000 mm x 10°
• For tractor units: 4 x 2, 6 x 2 and 6 x 4

Loading Area:
• Extendable loading platform, approx. 8,800 mm long with rear bevel approx. 500 mm x 10°
• A recess in the platform and rear bevel to accommodate the excavator dipper stick, approx. 3,950 x 580 x 370/450 mm

Ramps:
• One pair of two-piece steel ramps, approx. 4,350 mm long and 900 mm wide
• Hydraulically folding ramp tips
• Ramps hydraulically adjustable separately approx. 235 mm outwards and approx. 215 mm inwards
• Hardwood decking on the beveled part of the loading area
• Ramp with hardwood decking
• 20 x 30 mm square climbing strips, approx. every 200 mm on the outer frame of the ramp

Axles and Tyres:
• TWINAXLE-II independent wheel suspension with BPW stub axles, 1st axle steered in advance, all other axles are hydromechanically forced steered
• 1st axle with electromagnetic reverse lock via reverse gear and manual activation
• Technical axle load: 12,000 kg
• Hydr. axle compensation, hydraulic cylinders with shut-off valves
• Tyres 245/70 R 17.5
• TPMS tyre pressure monitoring system according to ECE R 141

Accessories Included:
• Plug-in steel front wall, approx. 400 mm high
• 4 wheel chocks with holder
• Front connection bar with yellow-red air couplings
• 3 kW electro-hydraulic power pack for hydraulic control, except for hydraulic winches
• 1 spare wheel
• 2 pairs of screw-in lashing rings
• 1 pair of horizontal lashing rings in the rear area of the gooseneck
• On the gooseneck: 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized
Cgodpfervw U Ssx Abpjw
• On the gooseneck: 1 plug-in ALU rear board, approx. 400 mm high, anodized
• Approx. 40 mm thick hardwood decking on the gooseneck, checker plate over the king pin
• 3.5" king pin
• Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide
• Load area locking with conically welded arresting profiles every 250 mm
• Incl. pre-tensioning plate
• 1 pair of lashing rings on the front cross member
• 8 pairs of recessed, fold-out lashing rings in the outer frame of the platform
• Extendable (galvanized) widenings approx. 230 mm per side
• 1 pair of fixed open wheel recesses up to extension, approx. 700 x 410 mm, in the platform in front of the 1st axle
• Wheel recesses with checker plate covering and 15 x 15 mm square climbing strips, approx. every 200 mm
• 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm, in the platform between the 1st and 2nd axle
• Wheel recesses with 15 x 15 mm square climbing strips and widenings in the lower section
• ALU covers for the wheel recesses between 1st and 2nd axle, which can also be used as broadening planks
• 1 pair of mechanical rear supports
• 20 x 30 mm square climbing strips, approx. every 200 mm on the outer frame of the bevel of the loading area
• Central lubrication system with 1 pump, BEKAMAX brand, standard grease as per NLGI-2
• Radio and cable remote control, with 2 indicator lights on the receiver for single wheel control
• WABCO Smart Board system
• The Smart Board is equipped with an odometer
• 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and mounts for rotating beacon

Oglas je bil avtomatsko preveden. Možne so napake pri prevodu.