Faymonville Max Trailer Max200 Sattelanhänger Megatrailer nakup rabljenega (30.037)

Stanje: novo, največja dovoljena obremenitev: 36.245 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.500 mm, skupna širina: 2.540 mm, Oprema: ABS, Our complete range of vehicles, including those available immediately and on short notice, can be found on our website. Extract from the specification. Full equipment details available on request. Loading Area: * Loading area with hardwood floor and rear bevel approx. 1,000 mm x 8° * 2 pairs of lashing rings (LC 5,000 daN) * 1 pair of lashing rings (LC 10,000 daN) * 6 pairs of fold-out lashing rings (LC 5,000 daN) * 2 pairs of fold-out lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the loading area for fastening straps (LC 2,000 daN) Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox, approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles, air suspension, disc brakes (approx. 377 mm), lift/lower function (ET 120) * Axle tool kit Tyres: * Tyres: 435/50 R 19.5, brand of our choice * TPMS tyre pressure monitoring system compliant with ECE R 141. Data transfer to the tractor unit via standardised EBS interface according to ISO 11992. For proper display, the truck must be capable of transmitting and displaying this data. Braking System: * Wabco braking system according to EU regulations, with EBS-E (2S2M), without connection lines to the tractor unit Steel Construction: * Steel structure made from high-tensile fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical System: * Electrical system according to EU regulations Lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicators * ASPÖCK-UNIBOX at the front connection bar with sockets 24N, 24S & 15-pin connector as per ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: * Complete steel structure automatically shot-blasted after welding with a wheel blasting machine Second abrasive blasting with corundum for optimal coating adhesion * HRM metal plating of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure optimal corrosion protection * Final coating with 2 layers of two-component finish, single-colour in RAL 3002 Carmine Red as per RAL system 841GL * Rear metal-coated and painted in RAL 9010 (Pure White) * Paint structure tested in salt spray test according to ISO 9227-NSS * Sealing of cavities with special wax Including the following additional equipment: * Yellow-red air couplings on the galvanised connection bar at the front * 4 wheel chocks with holder * 2-inch king pin * Loading area with heavy-duty hardwood floor Bsdpfsyvnfasx Al Hjlg * 1 spare wheel holder under the loading area, right-hand side * Galvanised folding supports under the rear loading area bevel * 9 pairs of stake pockets for insertable stanchions, approx. 100 x 50 mm, in the outer frame of the loading area * One galvanised steel front wall (EN12642-XL), approx. 1,600 mm high * Anti-slip sand coating painted on the centre beam * 1 INOX toolbox transverse under the loading area, approx. 1,000 x 400 x 2,500 mm * 6 pairs of WADER container pockets in the loading area, for 1x 20' container, 2x 20' containers, or 1x 40' container * 3 pairs of transverse stake pocket rails mounted in the loading area, for insertable stanchions approx. 100 x 50 mm * Storage for max. 9 pairs of insertable stanchions approx. 100 x 50 mm bolted to the inside of the front wall * 2 INOX toolboxes under the loading area left and right, approx. 600 x 350 x 600 mm * Holder for aluminium loading ramps, transverse under the loading area, behind the axles * One beacon light supplied

Stanje: rabljeno, največja dovoljena obremenitev: 37.535 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 08/2024, naslednji pregled (TÜV): 08/2026, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt from the equipment list. Full equipment details available upon request. Loading Platform: * Extendable loading platform with pneumatically actuated locking mechanism * 7 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * Cutouts in the outer frame of the loading platform for attaching lashing straps (LC 2,000 daN) Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles, air-suspended, with disc brakes (approx. 430 mm), with lift/lower function. Technical axle load: 10,000 kg each (ET0) * Follow-up steering axle with electro-magnetic reverse lock, activated via reverse gear or manually * Axle tool Tyres: * Tyres 385/65 R 22.5 Braking System: Bedpfexgk U Njx Al Hslg * Braking system compliant with EU regulations with EBS-E (2S2M) without interconnecting lines to the tractor unit Steel Structure: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Paintwork: * Premium and long-lasting corrosion protection for the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer * High-quality 2-component (2K) single-colour top coat finish in RAL 3002 carmine red * Silver rims * Rear section metallised and painted in RAL 9010 (pure white) Including the following additional equipment: * Yellow-red air couplings at the galvanised front connection panel * 4 wheel chocks with holders * 2-inch kingpin * Yellow reflector tape according to EU regulations, at the sides, on the extension, and rear of trailer * European reflector plates (red-yellow) at the rear of the trailer * Loading platform equipped with approx. 30 mm thick wooden floor, enclosed in omega profiles * 10 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading area * Storage for up to 9 pairs of plug-in stakes approx. 100 x 50 mm, bolted to the inside of the front wall * 1 spare wheel holder under the loading platform, left side in the direction of travel, without spare wheel * 1 mudflap at the rear of the trailer * Manual and description on USB stick * One bracket for a warning beacon at the rear of the trailer * On the gooseneck and rear panel, each left and right, a bracket for warning boards including socket * 80 km/h speed label at rear and on both sides * Load manometer for axle load determination including load diagram * Galvanised steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container locks in the loading floor, for 1x 20' container, 2x 20' containers or 1x 40' container flush with the rear * Stainless steel toolbox, approx. 600 x 350 x 600 mm, under the loading platform, left side in direction of travel * 4 pairs of stake pocket rails mounted lengthwise on the loading platform, for plug-in stakes 80 x 50 mm * Lift axle on the front axle, controlled by TEBS E depending on current axle load and loading status * 2 LED reverse lights mounted on the rear panel * HRM metallisation (High Resistance Metallisation)

Stanje: novo, največja dovoljena obremenitev: 38.500 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete vehicle inventory, including immediately and short-term available vehicles, can be found on our website. Excerpt from the equipment list. Full specification available upon request. EQUIPMENT: * Gooseneck, approx. 4,100 mm long, with central beam * Extendable loading platform, approx. 9,400 mm long, with rear bevel approx. 350 mm x 10° and integrated hook-in strip for attaching loose aluminium access ramps * Pneumatic locking with conical locking pin and reinforced locking positions; supply lines are routed protected inside the extendable beams and automatically adjust to the current platform length * Technical fifth-wheel load: 18,000 kg * Suitable for 4x2 and 6x2 tractor units * TPMS tire pressure monitoring system in accordance with ECE R 141 Bodpfx Aljy Augde Helg * BPW axles and suspension, all axles hydro-mechanically forced steered, mounted on turntables * Technical axle load: 12,000 kg per axle * Air suspension with lifting and lowering valve * 235/75 R 17.5 3PMSF twin tires. Brand subject to availability * ASPÖCK-UNIBOX * 3 kW electro-hydraulic pump unit for controlling hydraulic functions. Without installation of supply ports on the tractor unit * 4 pairs of recessed lashing rings in the outer frame of the gooseneck: - the first three pairs lying flat (LC 10,000 daN) - the rear pair foldable outward (LC 10,000 daN) * 4 pairs of stake pockets recessed in the outer frame of the gooseneck, for plug-in stakes approx. 100 x 50 mm * 2 inch kingpin * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B - static test load approx. 50,000 kg * Approx. 32 mm timber floor on gooseneck and platform, encased in aluminium omega profiles * 10 pairs of recessed lashing rings, foldable outward, in the outer frame of the platform * In front of the last axle and on the rear cross member of the semi-trailer, 1 pair of lashing rings each (LC 10,000 daN) * All other lashing rings (LC 5,000 daN) * 6 pairs of stake pockets recessed in the outer frame of the platform, for plug-in stakes approx. 100 x 50 mm * 1 spare wheel holder under the loading platform, on the right in the direction of travel * 1 lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the loading platform, left side in direction of travel * Bevel at the rear cross member of the vehicle, approx. 350 mm x 10° * Integrated hook-in strip for loose aluminium access ramps at the rear cross member of the vehicle * 1 pair of drop-in supports at the rear cross member * Remote steered axles from the front and rear using cable remote control, with single-track axle alignment, no installation required in the tractor unit * Round NATO socket at the front connector socket panel (Maeler & Kaege VG 96 917) * 1 LED work light on each side, left and right, mounted on the front wall with wiring to the connector socket for the tractor unit * On the extension an additional locking point every 500 mm * Holder for plug-in stakes, for storage when not in use, inside the front wall of the gooseneck * 4 wheel chocks with holder under the loading platform * Galvanized, sliding width extensions, extendable by approx. 230 mm per side (without timber planks) * 1 LED work light each side, left and right, in front of the axles with wiring to the connector socket for the tractor unit * 2 axle load gauges mounted on the left-hand side including axle load diagram * 1st axle with traction aid * Mounts for warning signs under the gooseneck and at left and right on the rear cross member * A

Stanje: rabljeno, največja dovoljena obremenitev: 36.650 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2021, naslednji pregled (TÜV): 11/2025, Oprema: ABS, Equipment extract Load area: - Load platform with extendable design featuring pneumatically operated locking system. - 2 pairs of flat lashing rings (LC 5,000 daN). Bsdpfx Alex Epzno Hjlg - 1 pair of lashing rings in the gooseneck (LC 10,000 daN). - 6 pairs of outward-folding lashing rings (LC 5,000 daN). - 3 pairs of outward-folding lashing rings (LC 10,000 daN). - Cut-outs in the outer frame of the load platform for attaching tensioning straps (LC 2,000 daN). Landing legs: - JOST mechanical landing legs with 2-speed gearbox, approx. 24 t lifting capacity (approx. 50 t test load). Tyres: - Tyres 245/70 R 17.5 – brand at our discretion. Load index (146/146F). Axles: - BPW axles, hydro-mechanically forced steering. - Air suspension with raising and lowering valve. - Axle tools. Brake system: - Brake system compliant with EU regulations with EBS-E (2S2M), without connection lines to the tractor unit. Steel construction: - Steel structure made of high-strength fine-grain steel grades: S355J2+N/S355MC (yield strength 355 MPa) and S690QL/S700MC (yield strength 690 MPa). Painting: - Premium, durable corrosion protection through 2-component (2K) zinc dust primer applied to the standard shot-blasted welded frame. - High-quality 2-component (2K) topcoat, single-color in RAL 3002 Carmine Red. - Rear section metallized and painted in RAL 9010 Pure White. - Rims silver (no metallic paint available). Electrical system: - Electrical installation as per EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3). - ASPÖCK-UNIBOX on the front connection rail with 24N, 24S & 15-pin sockets according to ISO (24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098). Warning signs: - One holder each on the gooseneck and rear panel, left and right, for warning signs including socket. Including the following additional features: - Remote steering from front and rear via cable remote with push buttons, includes single-track control of the axles (no installation in the tractor unit required). - Electro-hydraulic unit (± 45 kg). - 4 wheel chocks with holders on the front wall (± 5 kg). - 2-inch kingpin. - One galvanized steel front wall (EN12642-XL), approx. 1,600 mm high (± 35 kg). - Yellow-red air couplings on the galvanized front connection rail. - Yellow reflector tape in accordance with EU regulations on the sides, extension, and rear of the trailer. - European reflector signs (red-yellow) on the rear of the trailer. - One mud flap on the rear of the trailer. - Manual and description on USB stick. - Holder for a beacon on the rear of the trailer. - Load platform with heavy-duty hardwood floor. - 9 pairs of stake pockets, approx. 100 x 50 mm, in the outer frame of the load area (± 27 kg). - Extensions, galvanized, extendable up to approx. 230 mm each side (± 230 kg). - Spiral cable for supplying the electro-hydraulic unit and/or electric winch (approx. 35 mm², approx. 3.5 m long, max. 250 A) between trailer and tractor unit with NATO-NATO connections. - Galvanized supports under the sloped section of the load area. - Anti-slip sand coating applied to the central beam. - 6 pairs of WADER container locks in the load area for 1x20' container, 2x20' containers or 1x40' container; an additional locking position is provided in the extension for a 45' container (± 90 kg). - 4 pairs of transverse stake pocket strips, mounted across the load area for loose stakes approx. 100 x 50 mm (± 145 kg). - Storage for max. 9 pairs of loose stakes, approx. 100 x 50 mm, on the inside of front wall.

Stanje: novo, največja dovoljena obremenitev: 36.500 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle stock, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Full specifications available upon request. * Gooseneck, approx. 4,100 mm long with central beam * Platform deck, extendable twice, approx. 9,400 mm in length * BPW axles and suspension * All axles hydro-mechanically forced steered * Technical axle load: 12,000 kg * Air suspension with lifting and lowering valve * Tires: 235/75 R 17.5 3PMSF dual mounted * WABCO brake system, EBS-E * 3 kW electro-hydraulic power unit for hydraulic operations, without installation of supply connections at the tractor unit * 4 pairs of stake pockets recessed into the outer frame of the gooseneck, for insertable stakes approx. 100 x 50 mm * 2-inch king pin * 8 pairs of stake pockets recessed into the outer frame of the platform deck, for insertable stakes approx. 100 x 50 mm * 1 lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the deck on the left in the direction of travel Bljdpfewvzg Rsx Al Heg * Remote steering from the front and rear via cable remote control with push buttons; with single-track axle monitoring; no installation in the tractor unit * 2 axle load gauges mounted on the left side * Steel front wall, approx. 1,600 mm high * 3 transverse stake pocket strips in the platform deck, for insertable stakes approx. 100 x 50 mm * 1 transverse stake pocket strip in the gooseneck deck, for insertable stakes approx. 100 x 50 mm * 1 additional lockable INOX toolbox under the platform deck * WADER container pockets in the platform deck for transporting: 2x 20' containers or 1x 40' container * Central lubrication system with 2 pumps, brand BEKAMAX * Complete HRM metallization (High Resistance Metallisation)

Stanje: rabljeno, skupna masa: 39.500 kg, konfiguracija osi: 3 osi, prva registracija: 07/2022, dolžina tovornega prostora: 13.400 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 890 mm, Leto izdelave: 2022, Oprema: ABS, lfd 12389 LOW-LOADER MAX TRAILER 3-axle F-S43-1AAF / EXTENDABLE 4500 mm / STEERED AXLE Make/Manufacturer: MAX TRAILERS First registration: 07/2022 Dimensions: 13,400 x 2,540 x 890 mm Gross vehicle weight: 49,500 kg Unladen weight: 10,284 kg Payload: approx. 38,000 kg Kingpin load: 18,000 kg Air suspension with raise/lower function Drum brakes ABS EBS Mileage: 142,000 km Axle make: BPW 10.5 t Lifting axle Steered axle Trailing steering axle Lash rings Superstructure paint: red Chassis paint: GALVANIZED / RED Tyres: 12 units Tread depth: 7 - 10 mm Rear axle tyres: 235/75 R 17.5 MAX = FAYMONVILLE MAX 100 Ideal for concrete slabs / timber walls / precast concrete components etc. Side extension: 1,200 mm / hardwood floor Rear loading edge: 890 mm Lowered: 840 mm Bledpfx Aljy Ag Ads Heg Container locks for: 1 x 40/30 and 20 ft containers Includes 4 x twistlocks Stake pockets + 5 t lashing rings on floor EXTENDABLE by 4,500 mm in 500 mm increments Intermediate table can be removed TRAILING STEERED AXLE ALUMINIUM AIR TANK / HOT-DIP GALVANIZED EXCELLENT CONDITION!!!!! Currently, sample images from 06.2025 All details subject to change, prior sale reserved! If you have any questions regarding this or other vehicles, please call us. If you have any questions about this or another trailer/car, please call us.

Stanje: rabljeno, lastna masa: 14.995 kg, največja dovoljena obremenitev: 50.805 kg, skupna masa: 65.800 kg, konfiguracija osi: 3 osi, prva registracija: 10/2023, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, barva: siv, Leto izdelave: 2023, obratovalna teža: 14.995 kg, Oprema: ABS, For every used semi-trailer, you will receive a current and comprehensive inspection and functionality report. Gooseneck: - Gooseneck with rear bevel, approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading platform: - Extendable loading platform with rear bevel, approx. 500 mm x 8° - 6 pairs of fold-out lashing rings to the outside (LC 5,000 daN) - 4 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) - 1 intermediate section, 250 mm - Cut-outs in the outer frame of the loading area for inserting tensioning straps (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, chequer plate over the axles Axles and tyres: - BPW axles with hydro-mechanical forced steering - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - Axle tools - Tyres 235/75 R17.5 Braking system: - Braking system according to EU regulations with EBS-E (4S3M) Blsdpfx Alsv Hr Axs Hsg Accessories included: - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings mounted on the galvanized connection strip at the front - 4 chocks with holders on the front wall - One spare wheel with holder in front of the front wall - Electro-hydraulic power unit - Remote steering from front and rear via cable remote control with push buttons, including single-track control of the axles - Mounting for ALU ramps at the rear of the gooseneck - Hot-dip galvanized, extendable side extensions, approx. 230 mm per side - European reflector boards (red-yellow) at the rear of the trailer - White reflective tape as per EU standards on the sides, on the extension, and red at the rear - Bracket for warning signs on left/right of gooseneck and rear panel, incl. socket - Galvanized folding supports under the loading platform’s rear bevel - Holder for a beacon at the rear of the trailer - Central lubrication system with 2 BEKAMAX (Pico) pumps, NLGI-2 standard grease and removable cover for the pump - Mud flap at the rear of the trailer - Manual and documentation - On the gooseneck: insertable ALU side boards and rear wall, approx. 2,440 x 400 mm - Removable galvanized stanchions at the rear (body length approx. 2,560 mm) - 4 pairs of WADER container locks recessed in the loading platform for 1x 20ft, 2x 20ft, 1x 40ft, or 1x 45ft container - 8 pairs of pockets for removable stanchions, 100 x 50 mm, in the outer frame of the loading platform - Adjustable hook rails for ALU ramps at the rear of the vehicle - Lift axle on the front axle, controlled by TEBS E depending on current axle load and loading condition - Four warning panels, extendable approx. 400 mm, approx. 423 x 423 mm, each with position lamp - Mounting on warning panels for beacon - Radio remote control for remote steering in addition to cable remote control, with indicator lights on the receiver for single-track control - Painted-in sand layer on chequer plates, above the king pin and on the loading area for anti-slip protection - 80 km/h speed limit decal at the rear - Load pressure gauge for axle load determination, including load chart

Stanje: zelo dobro (rabljeno), konfiguracija osi: 2 osi, dovoljena osna obremenitev (os 1): 10.500 kg, dovoljena osna obremenitev (os 2): 10.500 kg, prva registracija: 06/2017, skupna dolžina: 7.000 mm, skupna širina: 2.500 mm, skupna višina: 880 mm, vzmetenje: zrak, velikost pnevmatike: 235/70 R17.5, stanje pnevmatik: 75 odstotek, barva: drugo, Leto izdelave: 2017, Oprema: ABS, = Dodatne možnosti in oprema = - 2 osi - Zračno vzmetenje Bjdey D Hl Iopfx Al Hjlg = Dodatne informacije = Konfiguracija osi Dimenzije pnevmatik: 235/70 R17.5 Profil pnevmatik: 75 % Zavore: bobnaste zavore Zadnja os 1: dvojna montaža; Največja obremenitev osi: 10.500 kg Zadnja os 2: dvojna montaža; Največja obremenitev osi: 10.500 kg Teža Dovoljena skupna masa: 21.000 kg Stanje Tehnično stanje: zelo dobro Vizualno stanje: zelo dobro Poškodbe: nobene Identifikacija Registrska številka: QALO590

Stanje: novo, največja dovoljena obremenitev: 40.320 kg, skupna masa: 50.960 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Selection of equipment. Complete specification available on request. Blsdoy Aug Dopfx Al Hsg Gooseneck: * Gooseneck with rear bevel approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick. Loading area with 5 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Landing Gear: JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Tyres: * 205/65 R17.5 tyres – manufacturer of our choice TPMS: * TPMS tyre pressure monitoring system in accordance with ECE R 141 Axles: * BPW axles, two rigid and two self-steering axles * Air suspension with lift/lower function * Drum brakes * Self-steering axles with electromagnetic reversing lock, activated via reverse gear or manually Brake system: * WABCO brake system compliant with EU regulations and EBS-E (4S3M) Electrical system: * Electrical system according to EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with indicator * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: * Steel structure made of high-strength fine grain steel * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) for optimal corrosion protection * Trailer colour RAL 3002 Carmine Red * Rims Silver Grey * Tarp RAL 9006 (brilliant direct) Options included: * At the gooseneck and at the rear, left and right, one bracket each for warning signs, including socket * 2-inch king pin * One galvanized steel front wall * Yellow-red air couplings at the galvanized front connection strip * 4 wheel chocks with holder on the front wall * 3 tiers of wooden boards * Galvanized folding supports under the loading area bevel * One bracket for a revolving warning light at the rear end of the trailer * Height-adjustable curtain structure – approx. 3,960 mm? * Galvanized front wall with tensioning mechanism for sliding curtains. Height adjustable by approx. 400 mm * Roof brand EDSCHA, can be slid forward on ALU roof profile beams (bolted to front and rear wall) * 3 pairs of movable stanchions in the loading area * Body hydraulically extendable to the left and right at the rear by approx. 750 mm * Sliding roof with fold-up portal beam * Sliding tarp with 700 mm reserve in length; tie-down straps at approx. 600 mm intervals. Height upper edge of body approx. 3,960 mm (loaded) * Driving with the sliding roof open is not permitted and will damage the tarp * Body at the rear closed with anodized ALU swing doors * Latch-on rail for ALU loading ramps at the rear of the vehicle * Control valves for hydraulic widening fitted to the right-hand side of the trailer * White reflective tape as per EU regulations on the sides, red at the rear * Electro-hydraulic unit under the rear loading area * One mudguard at the rear of the trailer * European reflective signs (red-yellow) at the rear of the trailer * Hand…

Stanje: novo, največja dovoljena obremenitev: 58.860 kg, skupna masa: 73.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete range of vehicles, including those available immediately and at short notice, on our website. Excerpt from the equipment list. Full specification available on request. Gooseneck: * Gooseneck with approx. 45° chamfered front corners and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring, approx. 30 mm thick Extendable loading platform: * Extendable loading platform with rear chamfer approx. 500 mm x 8° * 8 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Cutouts in the outer frame of the loading platform for attaching tensioning straps (LC 2,000 daN) * Hardwood flooring, approx. 48 mm thick; checker plate flooring over the axles Two-piece steel ramps: * One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 900 mm, with Super Grip rubber coating * Ramp with hydraulically folding and unfolding ramp sections * Hydraulic lifting mechanism, hydraulically adjustable * Maximum load per pair: 50,000 kg * In accordance with Regulation 1230/2012/EU, ramps with a length less than 300 mm do not need to be included in the overall vehicle length of 16,500 mm when in driving position Axles: * BPW axles and suspension, 1st axle with steering, 2nd and 3rd rigid, 4th and 5th axles trailing-steered, air suspension, with raise/lower function, drum brakes * Trailing steering axles with electromagnetic reverse lock, activated via reverse gear or manually * Technical axle load: 12,000 kg each Tyres: * Tyres 235/75 R 17.5 3PMSF – make of our choice TPMS: * TPMS tyre pressure monitoring system according to ECE R 141. Data transmission to the truck via standardized EBS interface according to ISO 11992. For correct display, the truck must be capable of receiving and displaying this data Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Brake system: * Wabco brake system in compliance with EU regulations with EBS-E (4S3M), without connecting lines to the tractor unit Blodpfx Aloy Augwj Hsg Steel structure: * Steel structure made from high-tensile fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Electrical system: * Electrical system in accordance with EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Complete steel structure automatically shot blasted after welding with a blast wheel system * Second blasting treatment with corundum for optimum adhesion of the coating system * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for maximum corrosion protection * Final paint finish with two coats of 2K topcoat, single color in RAL 3002 carmine red according to RAL system 841GL * Rear section metallized and painted in RAL 9010 (pure white) Including the following additional equipment: * 2-inch king pin * One galvanized steel front wall, approx. 400 mm high * A spare wheel carrier in front of the front wall * Yellow-red air couplings at the galvanized front connection strip * A bracket for a rotating beacon at the rear of the trailer * Galvanized supports under the chamfered section of the loading platform * Super Grip 2 rubber coati

Stanje: novo, največja dovoljena obremenitev: 36.020 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete inventory of vehicles available for immediate or short-term delivery on our website. Partial equipment listing. Full equipment details available upon request. Gooseneck: * Gooseneck with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area with rear bevel approx. 1,000 mm x 8° * 5 pairs of outward folding lashing rings (LC 5,000 daN) * 3 pairs of outward folding lashing rings (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) * Hardwood flooring approx. 48 mm thick, with checker plate covering over the axles Two-part steel ramps: * One pair of galvanized two-piece steel ramps, approx. 3,185 + 1,420 x 1,250 mm, with grating surface C40/5 (point load approx. 2.8 t on an area of approx. 20 x 20 cm) * Ramp with hydraulically folding ramp sections and hydraulic lifting mechanism * Maximum load per pair: 30,000 kg Landing legs: * JOST landing gears (manual) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, can be activated via reverse gear and manually * Air suspension with raise and lower valve Tyres: * 235/75 R 17.5 3PMSF tyres – manufacturer at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Brake system: * WABCO brake system compliant with EU regulations with EBS-E (2S2M) without connectors to the tractor unit Steel structure: * Steel construction made from high-tensile fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system in accordance with EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX at the front connector strip with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * HRM metalizing of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for optimal corrosion protection * Final coating with 2 layers of two-component topcoat, single colour in RAL 3002 carmine red, in accordance with RAL System 841GL * Rear section metalized and painted RAL 9010 (Pure White) * Wheels in silver Including accessories: * One bracket for warning signs on both sides at the gooseneck and at the rear, including socket * 1 spare wheel holder under the loading area on the right-hand side * 2" kingpin * Galvanized steel front wall * Yellow-red air couplings on the galvanized connector strip at the front * 4 wheel chocks with holders on the front wall * 3 height-adjustable wooden planks * Galvanized folding supports under the loading area bevel * Bracket for a rotating beacon at the rear of the trailer * Height-adjustable tarpaulin frame (approx. 3,960 mm) * Galvanized front wall with tensioning mechanism for sliding curtains, height-adjustable by approx. 400 mm * EDSCHA roof, forward-sliding, on aluminium roof beam profiles (bolted with front and rear wall) * 3 pairs of sliding stakes in the loading area Blodsy Auhuspfx Al Heg * Superstructure can be hydraulically widened at the rear to left and right by approx. 750 mm * Sliding roof with liftable portal carrier * Sliding tarpaulin with approx. 700 mm slack in length, with tensioning straps spaced approx. 600 mm

Stanje: novo, največja dovoljena obremenitev: 37.980 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: * Gooseneck with approx. 45° beveled front corners and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approx. 30 mm thick Loading platform (extendable version): * Extendable loading platform with rear chamfer approx. 1,000 mm x 8° * 6 pairs of folding-out lashing rings (LC 5,000 daN) * 3 pairs of folding-out lashing rings (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front of the loading platform (LC 10,000 daN) * Cut-outs in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) * Hardwood flooring, approx. 48 mm thick, with checker plate over the axles Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lift capacity (approx. 50 t static load) Tyres: * 235/75 R 17.5 3PMSF tyres – manufacturer at our discretion TPMS: * TPMS tyre pressure monitoring system in accordance with ECE R 141. Data transmission to the tractor unit is via the standardised EBS interface per ISO 11992. For correct display, the tractor unit must be able to transmit and display these data. Axles: Bljdpfxjy Aufmo Al Hsg * BPW axles and suspension, 2 rigid axles, 1 steering trailing axle * Technical axle load: 12,000 kg each * Electromagnetic reversing lock activated by reverse gear and manually * Air suspension with lift/lower valve * Axle tools Brake system: * Brake system compliant with EU regulations with EBS-E (2S2M), no connecting lines to the tractor unit Steel construction: * Steel construction made from high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: * Complete steel structure automatically shot-blasted after welding with blast wheel machine * Secondary blasting with corundum for optimal coating adhesion * Final painting with 2 layers of 2K topcoat, single colour RAL 3002 Carmine Red as per RAL System 841GL * Rims in silver-grey * Rear section metallized and painted in RAL 9010 (pure white) * Paint system tested in salt spray test per ISO 9227-NSS * Cavity sealing with special wax Electrical system: * Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights synchronized with the indicator * ASPÖCK-UNIBOX at the front connector rail with sockets: 24N, 24S, & 15-pin according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Accessories included: * 2-inch king pin * One galvanized steel front wall, approx. 400 mm high * One spare wheel carrier in front of the front wall * Yellow-red air couplings on the galvanized front connection rail * 4 chock blocks with holder at the front wall * Mount at the rear of the gooseneck for ALU approach ramps * Galvanized folding supports under the loading platform rear chamfer * At the gooseneck and on the rear panel, left and right, each with a bracket for warning signs including socket * Load gauge for determining axle loads with load diagram * On the gooseneck, plug-in aluminium side and rear walls, approx. 2,440 x 400 mm (L x H). The rear galvanized plug-in stanchions are removable. (Superstructure length approx. 2,560 mm) * One galvanized toolbox integrated in the beveled gooseneck * 3 pairs WADER C

Stanje: dober (rabljeno), konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 10.500 kg, dovoljena osna obremenitev (os 2): 10.500 kg, dovoljena osna obremenitev (os 3): 10.500 kg, prva registracija: 11/2022, skupna dolžina: 13.900 mm, skupna širina: 2.550 mm, skupna višina: 2.400 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 17.5, medosna razdalja: 2.300 mm, Leto izdelave: 2022, Oprema: ABS, = Additional Options and Equipment = - EBS (Electronic Braking System) - Rear air suspension - Spare wheel = Notes = - Faymonville / Max Trailer 3-axle low loader (Type: MAX100) - Loading platform dimensions: length 930 cm x width 254 cm - Extendable up to: 1280 cm (+350 cm) - Loading height: 91 cm - Lashing rings - Wheel recess - Widening inserts - Gooseneck dimensions: length 252 cm x width 247 cm x height 40 cm - Loading height: 149 cm - 2 ALTEC aluminium loading ramps (Type: VFR120) - Dimensions: length 235 cm x width 47 cm - Maximum incline: 30% (16.5°) - 10.5-ton axles! - 18-tonne fifth wheel pressure! - 49.5 tonnes gross vehicle weight! (Technical) - LIKE NEW CONDITION! - Always stored indoors! - Only 20,000 km driven! Bljdpeyztt Tefx Al Hog = Further Information = Axle configuration Tyre size: 235/75 17.5 Axle brand: BPW Suspension: air suspension Rear axle 1: twin tyres; max. axle load: 10,500 kg; tyre tread left inner: 70%; tyre tread left outer: 70%; tyre tread right inner: 70%; tyre tread right outer: 70% Rear axle 2: twin tyres; max. axle load: 10,500 kg; tyre tread left outer: 80%; tyre tread right outer: 80% Rear axle 3: twin tyres; max. axle load: 10,500 kg; steered; tyre tread left inner: 70%; tyre tread left outer: 70%; tyre tread right inner: 70%; tyre tread right outer: 70% Weights Unladen weight: 10,069 kg Payload: 35,931 kg gross vehicle weight: 46,000 kg Maintenance, history and condition Number of owners: 1 APK (MOT equivalent): valid until 11.2026 Technical condition: good Visual condition: good Identification Registration number: OT-87-PP Product Safety Manufacturer: Clean Mat Trucks B.V. Wageningsestraat 17 6673DB ANDELST, NL

Stanje: rabljeno, lastna masa: 11.200 kg, največja dovoljena obremenitev: 36.800 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 10/2025, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Leto izdelave: 2025, Oprema: ABS, For every used semi-trailer, you receive a current & comprehensive inspection and function report. Gooseneck: - Gooseneck with rear bevel of approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood floor Extendable loading area: - Telescopic loading area with rear incline approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses with 15 x 15 mm square climbing strips and widened sections in the lower area - Between the 1st and 2nd axle, 1 pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm - Incl. 3-piece removable galvanized covers over the wheel recesses (width 670 mm) – max. point load 5 t / pc - Recess in the incline and extending into the loading area for accommodating the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of swing-out lashing rings (LC 5,000 daN) - 2 pairs of swing-out lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator dipper recess (LC 5,000 daN) - Cutouts in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) Ramps: - One pair of galvanized, two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp sections, hydraulic lifting unit, and hydraulically adjustable - Maximum load per pair: 40,000 kg Axles and tires: - BPW axles and suspension, 2 rigid axles, 1 trailing self-steer axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock operable via reverse gear and manual activation - Air suspension with raise and lower valve - Axle tools - TPMS tire pressure monitoring system compliant with ECE R 141 - Tires: 235/75 R17.5 3PMSF Accessories included: - Bracket for warning signs on the gooseneck and at the rear, left and right, each with socket - One spare wheel with holder in front of the bulkhead - 2" kingpin - Galvanized steel front wall approx. 400 mm high - Yellow-red air couplings at the front galvanized connection rail - 4 wheel chocks with holders - Galvanized, extendable width extensions approx. 230 mm per side - Galvanized folding supports under the incline of the loading area - Cover plates to bridge the gap between ramps and loading area - White reflective tape on sides and on extendable section, rear in red, according to EU regulations - Electro-hydraulic unit at the rear, under the loading area Bledpfx Asyyldusl Hog - European reflector boards (red-yellow) on the rear of the semi-trailer - Four extendable warning signs, each approx. 423 x 423 mm with position lamp (extend approx. 400 mm) - Bracket for rotating beacon on the warning signs - On the gooseneck, plug-in aluminium side and rear boards approx. 2,440 x 400 mm - Rear, galvanized plug-in stanchions removable (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container - 3 pairs of stanchion pockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading area - Removable, galvanized intermediate table with 1 pair of WADER container pockets - 20 x 20 mm square climbing strips every 200 mm on the outer frame of the loading area incline - Painted sand layer as anti-slip protection on chequer plates on the gooseneck and loading area - Speed sticker 80 km/h on rear and both sides - Load manometer for determining axle loads, including load chart

Stanje: novo, skupna masa: 58.000 kg, Leto izdelave: 2026, MAX100 4 A 8.60 U Low Loader Semi-Trailer Technical Specifications Speed: 80 km/h Gross weight: 60,800 kg Fifth-wheel load: 18,000 kg Axle load: 42,800 kg Unladen weight: Payload: Gooseneck length: 3,850 mm Loaded fifth-wheel height: 1,250 mm Loading area length: 8,600 mm Extendable by: 5,400 mm Axle spacing: 1,360 mm Rear steering radius: 2,300 mm Loading height at max. load: 860 mm Overall width: 2,540 mm Suspension travel: -55/+145 mm Technical Description Gooseneck With front corners chamfered at 45° and rear bevel approx. 760 mm x 10° 3 pairs of lashing rings (LC 5,000 daN) Hardwood flooring, 30 mm thick Loading area, extendable version with rear bevel approx. 1,000 mm x 8° 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) 1 pair of horizontal lashing rings at front of loading area (LC 10,000 daN) Hardwood flooring approx. 48 mm thick, checker plate over axles Ramps Two-piece steel ramps One pair of galvanized two-piece steel ramps approx. 2,750 + 1,400 mm x 800 mm with approx. 48 mm thick hardwood covering Ramp with hydraulically folding ramp sections, hydraulic lifting system and hydraulically adjustable. Maximum load capacity per pair: 40,000 kg Tyres 235/75 R 17.5 Braking system in accordance with EU standards with EBS-E (4S3M) without connecting lines to the tractor unit Paintwork First-class, durable corrosion protection of the standard shot-blasted welded frame guaranteed by 2-component zinc-dust primer High-quality 2-component (2K) topcoat, single-color finish in RAL shades of your choice Rear section metallized and painted in RAL 9010 (pure white) Landing Gears: JOST mechanical landing gears with 2-speed gearbox for 24 t Lifting capacity (test load 50 t) Steel structure made of high-strength fine-grain steels. Steel Grades: Steel structure made of high-strength fine-grain steel S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrics in accordance with EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets. Connection in accordance with ISO. 24N ISO-1185 24S ISO-3731 15 pin ISO-12098 Accessories included: One galvanized steel front wall approx. 400 mm high 2" king pin 4 wheel chocks with holder on the front wall Bracket for a rotating beacon at rear of the trailer SAF axles, two fixed axles, one trailing-steering axle, air-suspended, with drum brake, with lifting/lowering function. Trailing steering axle with electro-magnetic reverse lock, can be activated via reverse gear or manually. Axle tools Mounting at the rear of the gooseneck for ALU loading ramps Galvanized folding supports under the bevel of the loading area Mechanical safety lock for the loading area Blsdpfeg Sk T Dox Al Heg One spare wheel with holder in front of the front wall Yellow reflective tape along the sides, extension and rear of trailer, in accordance with EU regulations. At the galvanized front connection strip, yellow-red air couplings On gooseneck and rear plate left and right, each with mount for warning plates and socket included Mudflap at trailer rear Manual and documentation On gooseneck, plug-in ALU sideboards and rear wall approx. 2,440 x 400 mm (L x H) The rear galvanized stake pockets are removable Body length approx. 2,560 mm, +/- 46 kg 3 pairs WADER container locks in the loading area for a 20', 30' or 40' container (± 30 kg) 6 pairs of stake pockets for plug-in stakes

Stanje: rabljeno, lastna masa: 10.650 kg, največja dovoljena obremenitev: 40.310 kg, skupna masa: 50.960 kg, konfiguracija osi: 3 osi, prva registracija: 10/2024, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5, barva: siv, Leto izdelave: 2024, obratovalna teža: 10.650 kg, Oprema: ABS, For every used semi-trailer, you receive a current and complete inspection and functional report. Gooseneck: - Gooseneck with 30 mm thick hardwood flooring - Rear section of gooseneck straight design - 3 pairs of lashing rings (LC 5,000 daN) Loading area: - Extendable loading area design - 5 pairs of fold-out lashing rings (LC 5,000 daN) - 3 pairs of fold-out lashing rings (LC 10,000 daN) - 1 pair of flush-mounted lashing rings at the front of the loading area (LC 10,000 daN) - Cutouts in the outer frame of the loading area for attaching tensioning straps (LC 2,000 daN) - Hardwood flooring approx. 48 mm thick, with checker plate flooring over the axles Axles and Tyres: - BPW axles, two fixed and two self-steering axles - Air suspension, drum brakes, with raise/lower function - Self-steering axles with electro-magnetic reverse lock, activatable via reverse gear or manually - Axle tools - Tyres 205/65 R17.5 Braking system: - WABCO braking system according to EU regulations with EBS-E (4S3M) Steel construction: - Steel construction made from high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355MPa) - S690QL/S700MC (yield strength 690MPa) Paintwork: - First-class, long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) top coat finish, single color, in Nova Grey Accessories included: - Spare wheel holder in front of the front wall - 2" king pin - Galvanized steel front wall, approx. 400 mm high - On the galvanized connector bar at the front, yellow-red air couplings - 4 wheel chocks with holders at the front wall - Galvanized folding supports under the loading area slope - Bracket for a revolving beacon at the rear of the trailer - Extendable galvanized side extensions, approx. 230 mm per side - White reflective tape on the sides in accordance with EU regulations, at extension and red at the rear - Mounts for warning boards on both sides of the gooseneck and rear apron, including socket - Rear mudflap - European reflective signs (red-yellow) at the rear of the trailer - TPMS tyre pressure monitoring system according to ECE R 141 - Plug-in ALU side and rear walls on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized plug-in stanchions are removable (body length approx. 2,560 mm) - 7 pairs of WADER container pockets: 1x 20ft container on the loading area; 1x 40ft container on the loading area; 1x 40ft container over the gooseneck; 2x 20ft container - 7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the loading area - Lift axle on the front axle with TEBS E control depending on current axle load and load condition - Movable hanging rail for ALU loading ramps at the rear of the vehicle - Sanded anti-slip coating painted on checker plates on the gooseneck and loading platform - Four approx. 400 mm extendable warning boards, approx. 423 x 423 mm, with position light - Mount for beacon on warning boards Blodpjxfa E Ujfx Al Hog - 80 km/h speed stickers on the rear and both sides - Load gauge for axle load determination, including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then all defined visible surfaces hot galvanized with ZINACOR 850 metallization (zinc 85%, aluminium 15%)

Stanje: rabljeno, lastna masa: 13.200 kg, največja dovoljena obremenitev: 52.800 kg, skupna masa: 66.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/2025, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 245/70 R 17,5, barva: siv, Leto izdelave: 2025, Oprema: ABS, For every used semi-trailer, you will receive a current and comprehensive inspection and function report. Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Extendable Load Area: - Extendable load area with rear chamfer approx. 1,000 mm x 8° - 5 pairs of fold-out lashing rings (LC 5,000 daN) - 3 pairs of fold-out lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the front of the loading platform (LC 10,000 daN) - Cutouts in the outer frame for attaching tension belts (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Axles and Tyres: - BPW axles and suspension, 1st axle rigid, all others hydro-mechanically forced-steered - Technical axle load: 12,000 kg - Air suspension with raise and lower valve - Tyres 245/70 R 17.5 - TPMS tyre pressure monitoring system according to ECE R 141 Bjdsyffd Djpfx Al Holg Two-part Steel Ramps: - One pair of galvanized two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramp sections hydraulically foldable and retractable, with hydraulic lifting and shifting - Max load per pair: 40,000 kg Included Accessories: - 2'' king pin - Galvanized steel front wall approx. 400 mm high - Yellow and red air couplings to the galvanized coupling rail at the front - 4 wheel chocks - One spare wheel - Electro-hydraulic power unit - Remote steering front and rear via cable remote control with push buttons, including axle alignment monitoring - Mounting at the rear of the gooseneck for ALU approach ramps - EU reflective panels (red-yellow) at the rear of the trailer - White reflective tape on sides, extension and rear in red (per EU regulations) - At the gooseneck and ramps, left and right, holder for warning boards including socket - Holder for a rotating beacon at the rear of the trailer - Galvanized folding supports under the chamfered load area - Ramp control valves mounted on the right trailer side - Cover plates to bridge the gap between ramps and load area - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 - On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm - Rear galvanized plug-in stanchions removable (structure length approx. 2,560 mm) - INOX toolbox 1,350x400x400 mounted on the gooseneck, box covers oil filler cap - 4 pairs of WADER container lock pockets on load area, for 1x 20ft, 2x 20ft, 1x 40ft or 1x 45ft container - 7 pairs of stake pockets for 100 x 50 mm plug-in stanchions in outer frame - Galvanized, extendable platform wideners approx. 230 mm per side - Square-section climbing strips 20 x 20 mm every 200 mm on the outer frame of the chamfer - Lift axle on front axle with TEBS E control, based on axle load and loading condition - Four extendable warning signs, approx. 400 mm extension, dimensions 423 x 423 mm each with position light - Radio remote control for rear axle steering, in addition to cable remote, with signal lights for axle alignment on receiver - Anti-slip sand coating painted on checker plate surfaces of gooseneck and load area - 80 km/h speed decals rear and on both sides

Stanje: novo, največja dovoljena obremenitev: 47.300 kg, skupna masa: 58.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.600 mm, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment list. Complete equipment details available upon request. Gooseneck: * Gooseneck with chamfered front corners approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area in extendable design with rear chamfer approx. 1,000 mm x 8° * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN) * 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) * Recesses in the outer frame of the loading area for securing straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate flooring above the axles Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Tyres: * Tyres 235/75 R 17.5 3PMSF, manufacturer of our choice Axles: * BPW axles, two rigid axles, two self-tracking axles, air suspension, drum brake, with lifting/lowering function * The self-tracking axles can be locked for reversing by electro-magnetic reverse lock via reverse gear or manually * Axle tools Brake system: * WABCO brake system in compliance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system: * Electrical system in accordance with EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting * ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Premium and durable corrosion protection for the standard shot-blasted welded frame ensured by a two-component (2K) zinc dust primer * High-quality two-component (2K) topcoat, single colour, RAL 3002 Carmine Red * Rear section metallised and painted in RAL 9010 (Pure White) * Rims in silver Accessories: * Spare wheel holder in front of the front wall (without spare wheel) * 2-inch king pin * Galvanised steel front wall approx. 400 mm high * Yellow-red air couplings on the galvanised connection strip at the front * Mount in the rear area of the gooseneck for ALU loading ramps * Galvanised folding supports under the rear chamfer of the loading area Bodpfsyvnfgsx Al Hjlg * Holder for a beacon at the rear of the trailer * On the gooseneck and at the rear end panel, left and right, holders for warning signs including socket * TPMS tyre pressure monitoring system according to ECE R 141 * On the gooseneck, plug-in aluminium side walls and tailgate, approx. 2,440 x 400 mm (L x H). The rear galvanised plug-in stanchions are removable. (Body length approx. 2,560 mm) * Galvanised toolbox integrated into the chamfered gooseneck * 3 pairs of WADER container pockets recesses in the loading area for a 20' (30') or 40' container * Sliding hooks for aluminium loading ramps at the rear of the vehicle * 6 pairs of stanchion pockets for plug-in stanchions approx. 100 x 50 mm in the outer frame of the loading area * Galvanised extensions, extendable by approx. 230 mm per side * Lift axle on the front axle with control via TEBS E depending on the current axle load and current loading status * 2 LED reversing lights mounted on the rear end panel * 2 pairs Ferry-

Stanje: rabljeno, največja dovoljena obremenitev: 44.420 kg, skupna masa: 53.000 kg, konfiguracija osi: 3 osi, prva registracija: 04/2025, naslednji pregled (TÜV): 04/2026, dolžina tovornega prostora: 11.500 mm, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete range of immediately and soon available vehicles on our website. Excerpt from the equipment. Complete equipment details on request. Loading platform: * Loading bed with approx. 30 mm thick hardwood floor * 9 pairs of folding lashing rings towards the outside (LC 10,000 daN) * 10 pairs of stake pockets in the outer frame of the loading platform for plug-in stakes approx. 100 x 50 mm Landing gear / Support legs: * Hydraulic landing gear Tyres: * Tyres 385/65 R 22.5 - MICHELIN MULTI High Load 164K TPMS: * TPMS tyre pressure monitoring system according to ECE R 141. Data transmission to the truck is carried out via the standardised EBS interface according to ISO 11992. For correct display, the truck must be capable of transmitting and displaying this data. Axles and suspension: * BPW axles, technical capacity 10,000 kg each, first axle hydro-mechanically steered, second axle fixed, and third axle hydro-mechanically forced-steered, mounted on turntable * Air suspension with raise/lower valve Brake system: * WABCO brake system according to EU regulations with EBS-E (4S3M), without connecting lines to the tractor unit Electrical system: * Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front connection rail with sockets 24N, 24S & 15-pin connectors according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Coating: * Entire steel construction shot-blasted automatically after welding using a turbine blast machine * Second blasting treatment with corundum for optimal adhesion of the coating system * HRM metallisation of the entire chassis with ZINACOR 850 (85% zinc/15% aluminum) for maximum corrosion protection * Final coating with 2 layers of 2K topcoat, single color in RAL 9005 Jet Black as per RAL System 841GL * Rear section metallised and painted in RAL 9010 (Pure White) * Rims in silver grey * Coating tested by salt spray test according to ISO 9227-NSS * Cavities sealed with special wax Included accessories: * Loading platform with approx. 30 mm thick hardwood floor * 2-inch king pin * One galvanized steel front wall (EN12642-XL), approx. 1,200 mm high * DUOMATIK air couplings at the galvanized connection rail at the front * Storage for approx. 1,000 mm plug-in stakes, rear in the central beam * On the gooseneck and on the rear panel left and right, each with a bracket for warning panels including socket * White reflective tape in accordance with EU regulations on the sides and red at the rear * 10 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading platform * European reflective plates (red-yellow) at the rear of the trailer * One holder for a rotating beacon at the rear of the trailer * One mud flap at the rear of the trailer * Manual and description on USB stick * BEKAMAX central lubrication system (Pico) with standard grease NLGI-2 and removable pump cover Blsdjyu Eu Iopfx Al Heg * 4 wheel chocks with holder on the front wall * Steering from the front and rear via cable remote control with push buttons, with axle tracking control (without installation in the tractor unit) * Electro-hydraulic unit * 6 pairs of galvanized plug-in stakes, approx. 100 x 50 mm, approx. 1,000 mm high * 5 pairs of crosswise stake pocket bars mounted in the loading plat

Stanje: novo, največja dovoljena obremenitev: 90.700 kg, skupna masa: 126.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.850 mm, Oprema: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: Hydraulically lift/lower and detachable gooseneck. Length approx. 3,650 mm. Suitable for tractor units: 6x4 or 8x4 3-axle compact front bogie: * Hook mounts at front and rear. Length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Lowbed: * ATX-A lowbed with telescopic longitudinal beams in low-profile design, fixed hardwood floor approx. 50 mm thick * With drive-over bridge hooks at the front and bolt-lug coupling at the rear * Base width: approx. 2,850 mm, length: approx. 7,150 mm, beam height: approx. 330 mm, beam width: approx. 750 mm * Loading height approx. 480 mm, ground clearance approx. 150 mm 5-axle rear bogie: * Mechanical bolt-lug coupling for attaching a lowbed at the front; rear end traverse * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * Pendulum axle 3-axle front bogie: * PENDULUM AXLES, all axles hydro-mechanically forced-steered * Hose rupture valve on axle leveling cylinder with automatic RESET function * Hydraulic cylinders with shutoff taps and locking pins for securing in raised position * Final painting of axles with 2 coats of single color 2K paint, painted in MB7350 Novagrau * Rated axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tires for front bogie: 12 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J 5-axle rear bogie: * PENDULUM AXLES, all axles hydro-mechanically forced-steered * Hose rupture valve on axle leveling cylinder with automatic RESET function * Hydraulic cylinders with shutoff taps and locking pins for securing in raised position * Final painting of axles with 2 coats of single color 2K paint, painted in MB7350 Novagrau * Rated axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tires for rear bogie: 20 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimum corrosion protection * Final painting with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, according to RAL-System 841GL Bedpjw Tgp Dofx Al Holg Including accessories: * Steel front wall, approx. 400 mm high * Plug-in aluminum side and rear boards on gooseneck, approx. 400 mm high, anodized * 3.5" kingpin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections on gooseneck * Front bogie with separate air connection for air impact wrench * BEKA-MAX central lubrication for one 3-axle bogie * Preparation for bolt-on container positioning for 1 x 20' or 1 x 30' on the outer beams * Without container locks * Brackets on the outer beams for installing foldable extensions * One 7-pin socket left and right, front and rear on rear bogie for warning panels * BEKA-MAX central lubrication for one 5-axle bogie * On the rear bogie, socket for cable remote control for steering * Rear bogie with trough * 2 LED reversing lights mounted on rear panel * European reflector boards (red-yellow) on the rear * One mudflap at rear * One LED beacon with bracket left and right on rear cross-member * Two INOX toolboxes 855 x 340 x 390 mm on gooseneck, left and right * 1-circuit...

Stanje: novo, lastna masa: 11.000 kg, največja dovoljena obremenitev: 38.500 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm hardwood flooring Load Area: - Extendable loading area with rear taper approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses fitted with square climbing strips 15 x 15 mm, including lower extensions - Between the 1st and 2nd axle, a pair of fixed wheel recesses with cover, approx. 1,610 x 970 x 400 mm - Recess in the bevel as well as protruding into the loading area for parking excavator dipper stick approx. 2,900 x 750 x 210/290 mm - 1 pair of lashing rings, installed flat at the front of the load area (LC 10,000 daN) - 5 pairs of folding lashing rings on the outside (LC 5,000 daN) - 2 pairs of folding lashing rings on the outside (LC 10,000 daN) - 2 pairs of lashing rings in the dipper stick recess (LC 5,000 daN) - Cut-outs in the outer frame of the load area for securing straps (LC 2,000 daN) - Incl. three-part removable galvanized covers over the wheel recesses – max. point load 3.5 t / pc. Two-piece Steel Ramps: Bsdpfx Ajup U Hzel Hslg - One pair of galvanized, two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood surfacing - Ramp with hydraulically folding ramp sections, hydraulic lifting gear, and hydraulically adjustable Axles and Tyres: - BPW axles and suspension, 2 rigid axles, 1 steering trailing axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lifting and lowering valve - Axle tool kit - Tyres 235/75 R 17.5 - TPMS tyre pressure monitoring system in accordance with ECE R 141 Accessories Included: - Mounts for warning signs left and right at the gooseneck and at the rear, each with socket - One spare wheel - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings at the galvanized front connector strip - 4 wheel chocks - Galvanized, extendable outriggers approx. 230 mm per side - Galvanized folding supports beneath the loading area bevel - Rear trailer bracket for rotating beacon - Cover plates for bridging the gap between ramps and load area - White reflective tape to EU regulations, sides and on extensions; rear in red - Electro-hydraulic unit installed at the rear beneath the loading area - Ramp control valves mounted on right trailer side - European reflective panels (red-yellow) on rear of trailer - Four extendable warning boards, approx. 423 x 423 mm, with position light - Bracket for rotating beacon on warning boards - Removable ALU side boards and rear board on gooseneck approx. 2,440 x 400 mm - Rear galvanized removable stakes (structure length approx. 2,560 mm) - 2 pairs of WADER container pockets in loading area for 20ft or 30ft container - 3 pairs of socket pockets for stakes 100 x 50 mm in outer frame of loading area - Removable, galvanized intermediate table with 1 pair of WADER container pockets - Square climbing strips 20 x 20 mm spaced every 200 mm on outer frame at loading bevelling - Painted sand layer on chequer plates of the gooseneck and loading area for anti-slip protection - 80 km/h speed stickers rear and both sides - Load manometer for axle load measurement, including load chart.

Stanje: novo, lastna masa: 10.700 kg, največja dovoljena obremenitev: 38.800 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17,5, barva: sivo-črna, Oprema: ABS, Gooseneck: • Gooseneck with front corners beveled at 45° and rear taper approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Extendable loading platform: • Loading platform in extendable design with rear taper approx. 1,000 mm x 8° • Cut-outs in outer frame of loading platform for attaching tensioning straps • Approx. 48 mm thick hardwood flooring; anti-slip checker plate covering above the axles Two-piece steel ramps: • One pair of galvanized, two-piece steel ramps with approx. 48 mm thick hardwood covering • Ramps with hydraulically foldable ramp sections, hydraulic lift system, and hydraulically adjustable • Maximum load per pair: approx. 40,000 kg Axles and tires: • BPW axles and suspension, 2 rigid axles, 1 self-steering axle • Technical axle load: 12,000 kg • Electromagnetic reverse lock, activated via reverse gear or manually • Air suspension with lift and lower valve • Axle tools • 235/75 R 17.5 3PMSF Braking system: • WABCO braking system according to EU regulations with EBS-E Paintwork: • First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component zinc dust primer • High-quality, single-color top coat in MB 7350 Novagrey applied with two-component paint • Rear section metallized and painted in RAL 9010 Landing legs: • JOST landing legs with 2-speed gearbox for 24t lifting load (50t test load) Steel construction: • Steel construction made of high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC • S690QL/S700MC Electrical system: • Electrical system in accordance with EU regulations, 24 Volt lighting • ASPÖCK-UNIBOX on front connection panel with 24N, 24S & 15-pin sockets Accessories included: • One spare wheel with holder • Galvanized steel front wall approx. 400 mm high • Yellow-red air couplings on the galvanized front connection panel • 4 wheel chocks • Rear mounting bracket for beacon light at the end of the semitrailer • Recess at rear of gooseneck for ALU approach ramps • Galvanized folding supports under the loading platform taper • Cover plates to bridge the gap between ramps and loading platform • White reflector tape per EU regulations on sides, extension, and red at rear Bledehlz S Nopfx Al Hjg • Electro-hydraulic unit at rear, under the loading platform • On gooseneck and ramps, left and right, each with a holder for warning signs, including socket • Operating valves for the ramps located on the right side of the trailer • ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) • Four warning panels extendable by approx. 400 mm with a position light • 3 pairs of WADER container pockets in the loading platform for one 20ft, 30ft or 40ft container • 6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading platform • Galvanized extensions, extendable by approx. 230 mm per side • 20 x 20 mm square climbing strips every 200 mm on the outer frame of the platform taper • Painted anti-slip sand layer on checker plates, above king pin and loading platform • Load gauge for axle load measurement, including load diagram • HRM metallization (High Resistance Metallisation) of the outer frame • Complete steel construction shot-blasted, then defined visible surfaces metallized and hot-finished with ZINACOR 850 (Zinc 85% - Alu 15%)

Stanje: novo, lastna masa: 10.300 kg, največja dovoljena obremenitev: 39.200 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Platform: - Loading platform after the gooseneck, hydraulically liftable and lowerable, length approx. 2,800 mm, with rear chamfer approx. 1,000 mm x 8° - Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, over the axles with chequer plate covering Two-part Steel Ramps: - One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp parts, hydraulic lifting system, and hydraulically adjustable - Maximum load per pair: 40,000 kg Axles, Suspension and Tires: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated by reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tires 235/75 R 17.5 3PMSF - TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories Included: - One spare wheel with holder in front of the bulkhead - 2" kingpin - One galvanized steel front wall approx. 400 mm high - Yellow-red air couplings at the galvanized connection strip in front - 4 wheel chocks - Galvanized folding supports under the platform's rear chamfer - A holder for a rotating beacon at the rear of the trailer - Cover plates to bridge the gap between ramps and platform - White reflective tape as per EU regulations along the sides of the trailer and red at the rear - Electro-hydraulic unit at the rear, under the platform - At the gooseneck and at the ramps left and right, each with a holder for warning signs, including socket - Control valves for the ramps positioned on the right side of the trailer - European reflective plates (red-yellow) at the rear of the trailer - Manual and description on USB stick - Removable ALU side walls and rear wall on the gooseneck approx. 2,440 x 400 mm - The rear, galvanized side stakes are removable (body length approx. 2,560 mm) - An electric cable winch with radio remote control, approx. 5,400 kg lifting force, including 9.5 mm steel cable, 24 m long, with guide roller - Bolted 5 t ring for cable deflection of the winch on the gooseneck without pulley - 2 pairs WADER container pockets in the platform for a 20ft container - 6 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the platform - Lift axle on the front axle with control via TEBS E, depending on actual axle load and loading condition - 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN) - 1 pair of recessed lashing rings along the central beam at the rear chamfer (LC 10,000 daN) Bodpfx Alou Hp Hro Hslg - Sand coating for slip resistance painted on the chequer plates on the gooseneck and on the platform - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and removable pump protection - Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm - Speed stickers 80 km/h rear and on both sides - Load manometer for determining axle loads including load chart - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then all defined visible surfaces metallized and hot-coated with ZINACOR 850 (zinc 85% - alu 15%)

Stanje: novo, lastna masa: 14.800 kg, največja dovoljena obremenitev: 61.700 kg, skupna masa: 76.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck with rear chamfer of approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Loading Platform: • Extendable loading platform with rear chamfer of approx. 500 mm x 8° • 9 pairs of folding external lashing rings • 1 pair of recessed lashing rings at the front of the loading platform • Cutouts in the outer frame of the loading platform for attaching tension belts • Approx. 48 mm thick hardwood flooring, checker plate above the axles Landing Legs: • JOST mechanically operated landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: • BPW axles and suspension, 1st axle steering, 2nd and 3rd axle fixed, 4th and 5th axle follow-steering • Technical axle load: 12,000 kg • 1st, 4th, and 5th axles with electromagnetic reverse lock, activated via reverse gear or manually • Tyres: 235/75 R 17.5 3PMSF Brake System: • WABCO brake system in accordance with EU regulations including EBS-E (4S3M) Paintwork: • Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer • High-quality single-color two-component (2K) topcoat in MB 7350 Novagrau • Rear section metallized and painted in RAL 9010 (Pure White) Steel Construction: • Steel structure made from high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC (yield strength 355MPa) • S690QL/S700MC (yield strength 690MPa) Accessories: • One spare wheel with holder in front of the front wall • 2" king pin • Galvanized steel front wall, approx. 400 mm high • Front galvanized connection strip with yellow-red air couplings • 2 wheel chocks with holders mounted on the front wall Blsdpfxjma Hf Ro Al Hsg • Rear mount on gooseneck for ALU drive-on ramps • Galvanized extendable wideners appx. 230 mm per side • Bracket for a beacon at the rear of the trailer • Galvanized supports under the chamfer of the loading platform • White reflector tape on the sides as per EU regulations, red at the extension and rear • Mounts for warning panels including socket left and right at the gooseneck and rear panel • Detachable ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • Rear galvanized plug-in stanchions removable (body length approx. 2,560 mm) • 3 pairs of WADER container pockets in the loading platform for a 20ft (30ft) or a 40ft container • 7 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform • Lifting axle on the front axle with TEBS E control according to the current axle load and loading condition • Movable mounting rails for ALU drive-on ramps at the rear of the vehicle • 20 x 20 mm square climbing strips at 200 mm intervals on the outer frame chamfer of the loading platform • BEKAMAX (Pico) centralized lubrication system with NLGI-2 standard grease and removable pump cover • Four extendable warning panels approx. 423 x 423 mm with a position light, extendable by approx. 400 mm • Holder for beacon mounted on the warning panels • European reflector plates (red-yellow) on the rear of the trailer • 80 km/h speed limit stickers at rear and both sides • Axle load gauge with load diagram included • HRM Metallisation (High Resistance Metallisation) of the outer frame • Complete steel structure is shot-blasted, then defined visible surfaces are metallized with ZINACOR 850 (zinc 85% - aluminum 15%) using hot finishing

Stanje: novo, lastna masa: 10.350 kg, največja dovoljena obremenitev: 39.150 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Loading area: - Telescopic loading area with rear chamfer approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm - Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom - Between the 1st and 2nd axle, 1 pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm - 3-piece detachable galvanized covers over the wheel recesses (W 670 mm) – max. point load 5 t / pc. - Recess in the chamfer and protruding into the loading area for the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of foldable external lashing rings (LC 5,000 daN) - 2 pairs of foldable external lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) - Cutouts in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) One-piece aluminum ramps: - 1 pair one-piece ALU ramps, approx. 2,500 x 600 mm - Ramp with spring lifting mechanism and manually adjustable - Maximum load per pair: 24,000 kg Axles and tires: - BPW axles and suspension, 2 rigid axles, 1 trailing steering axle - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool Bodpfx Aleiu Er Ao Hjlg - Tyres 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 Accessories included: - 1 spare wheel with holder in front of the bulkhead - 2" kingpin - 1 galvanized steel front wall approx. 400 mm high - At the galvanized coupling rail at the front, yellow-red air couplings - 4 wheel chocks with holder at the bulkhead - Mounting point at the rear of the gooseneck for ALU ramps - Galvanized extensions, extendable by approx. 230 mm per side - Galvanized folding supports under the chamfer of the loading area - 1 holder for a rotating beacon at the rear of the trailer - White reflective tape laterally, at the extension, and red at the rear, per EU regulations - At the gooseneck and rear panel, left and right, each with a holder for warning signs including socket - On the gooseneck, plug-in ALU sideboards and rear wall, approx. 2,440 x 400 mm - The rear galvanized stakes are removable (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container - 3 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area - 1 removable galvanized intermediate table with 1 pair of WADER container pockets - 20 x 20 mm square climbing strips every 200 mm on the outer frame in the chamfer of the loading area - Anti-slip sand coating on the checker plates on the gooseneck and the loading area - Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with position light - Holder for rotating beacon on the warning signs - 80 km/h speed stickers at the rear and on both sides - Load gauge for determining axle loads including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then all defined visible surfaces metalized and hot-finished with ZINACOR 850 (Zinc 85% – Alu 15%)