Priklopnik sedeža z delovno ploščadjo

FAYMONVILLE MAX Trailer MAX200 Sattelanhänger Megatrailer

Our complete range of vehicles, including those available immediately and on short notice, can be found on our website.

Extract from the specification. Full equipment details available on request.

Loading Area:
* Loading area with hardwood floor and rear bevel approx. 1,000 mm x 8°
* 2 pairs of lashing rings (LC 5,000 daN)
Itodpfxeyvnfao Ab Hed
* 1 pair of lashing rings (LC 10,000 daN)
* 6 pairs of fold-out lashing rings (LC 5,000 daN)
* 2 pairs of fold-out lashing rings (LC 10,000 daN)
* Cut-outs in the outer frame of the loading area for fastening straps (LC 2,000 daN)

Landing Legs:
* JOST landing legs (mechanical) with 2-speed gearbox, approx. 24 t lifting capacity (approx. 50 t test load)

Axles:
* BPW axles, air suspension, disc brakes (approx. 377 mm), lift/lower function (ET 120)
* Axle tool kit

Tyres:
* Tyres: 435/50 R 19.5, brand of our choice
* TPMS tyre pressure monitoring system compliant with ECE R 141. Data transfer to the tractor unit via standardised EBS interface according to ISO 11992. For proper display, the truck must be capable of transmitting and displaying this data.

Braking System:
* Wabco braking system according to EU regulations, with EBS-E (2S2M), without connection lines to the tractor unit

Steel Construction:
* Steel structure made from high-tensile fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa)

Electrical System:
* Electrical system according to EU regulations Lighting 24 Volt ASPÖCK-NORDIK (ASS3)
* All LED side marker lights flash with the indicators
* ASPÖCK-UNIBOX at the front connection bar with sockets 24N, 24S & 15-pin connector as per ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098

Paintwork:
* Complete steel structure automatically shot-blasted after welding with a wheel blasting machine Second abrasive blasting with corundum for optimal coating adhesion
* HRM metal plating of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure optimal corrosion protection
* Final coating with 2 layers of two-component finish, single-colour in RAL 3002 Carmine Red as per RAL system 841GL
* Rear metal-coated and painted in RAL 9010 (Pure White)
* Paint structure tested in salt spray test according to ISO 9227-NSS
* Sealing of cavities with special wax

Including the following additional equipment:
* Yellow-red air couplings on the galvanised connection bar at the front
* 4 wheel chocks with holder
* 2-inch king pin
* Loading area with heavy-duty hardwood floor
* 1 spare wheel holder under the loading area, right-hand side
* Galvanised folding supports under the rear loading area bevel
* 9 pairs of stake pockets for insertable stanchions, approx. 100 x 50 mm, in the outer frame of the loading area
* One galvanised steel front wall (EN12642-XL), approx. 1,600 mm high
* Anti-slip sand coating painted on the centre beam
* 1 INOX toolbox transverse under the loading area, approx. 1,000 x 400 x 2,500 mm
* 6 pairs of WADER container pockets in the loading area, for 1x 20' container, 2x 20' containers, or 1x 40' container
* 3 pairs of transverse stake pocket rails mounted in the loading area, for insertable stanchions approx. 100 x 50 mm
* Storage for max. 9 pairs of insertable stanchions approx. 100 x 50 mm bolted to the inside of the front wall
* 2 INOX toolboxes under the loading area left and right, approx. 600 x 350 x 600 mm
* Holder for aluminium loading ramps, transverse under the loading area, behind the axles
* One beacon light supplied

Oglas je bil avtomatsko preveden. Možne so napake pri prevodu.