Odprta polprikolica s ponjavo

DINKEL 3-Achs-Sattelanhänger, Pritsche+Plane, LBW

Stanje: rabljeno, lastna masa: 11.950 kg, največja dovoljena obremenitev: 37.550 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, prva registracija: 02/2025, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, barva: siv, Leto izdelave: 2025, Oprema: ABS, For every used semi-trailer, you will receive a current and comprehensive inspection and functionality report. Gooseneck: - Gooseneck with rear chamfer of approx. 750 mm x 10° - 3 pairs of lashing rings - 30 mm thick hardwood flooring Two-piece steel ramps: - One pair of galvanized two-piece steel ramps, approx. 3,185 x 1,420 x 1,250 mm, with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system - Maximum load per pair: 30,000 kg Loading platform: - Loading area with rear chamfer of approx. 1,000 mm x 8° - 5 pairs of externally foldable lashing rings - 3 pairs of externally foldable lashing rings - 1 pair of flat lashing rings at the front of the loading area - Approx. 48 mm thick hardwood flooring; tread plate surface above the axles Axles and wheels: - BPW axles and suspension; two axles fixed, one self-steering axle - Air suspension with raise/lower valve - Self-steering axles with electro-magnetic reverse lock, activated via reverse gear or manually - Tyres: 235/75 R17.5 3PMSF Accessories included: - 1 spare wheel with holder - TPMS tyre pressure monitoring system in accordance with ECE R 141 - 2" kingpin - One galvanized steel bulkhead - Yellow-red air couplings at the galvanized front connector rail - 4 wheel chocks with holders - Recess at the rear of the gooseneck for ALU access ramps - 3 heights of aluminum planks - Galvanized folding supports under the chamfer of the loading platform - A holder for a revolving beacon at the rear of the trailer - Height-adjustable tarpaulin structure (3,960 mm) - Galvanized front wall with a tensioning mechanism for the sliding curtain - Height adjustment possible by approx. 400 mm - "EDSCHA" branded roof, forward-slidable on aluminum roof beam profiles, bolted to front and rear walls - 3 pairs of sliding stanchions on the loading area - Structure hydraulically extendable at the rear by approx. 750 mm to the left and right - Sliding roof with pivotable portal beam - Sliding curtain with 700 mm length reserve, tension belts spaced approx. 600 mm apart - Height to top edge of structure approx. 3,960 mm - Driving with an open sliding roof is not permitted and will lead to damage of the tarpaulin - Cover plates to bridge the gap between ramps and loading platform - Electro-hydraulic unit at the rear, under the loading platform - At the gooseneck and ramps, left and right respectively, one holder for warning signs including socket - European reflective signs (red-yellow) at the rear of the trailer - 6 pairs of stanchion pockets for plug-in stanchions 100 x 50 mm on the outer frame of the loading area - Lifting axle at the front axle with control via TEBS E depending on current axle load and loading condition - Grating surface in the chamfer of the loading platform C40/4 (point load 3.4 t on an area of 20 x 20 cm) Laedpjy Drdcofx Ahkoa - One INOX toolbox 565 x 290 x 810 mm on the right in the direction of travel, between the axles - Painted sand layer on tread plates on the gooseneck and loading platform as anti-slip protection - BEKAMAX (Pico) central lubrication system with standard grease NLGI-2 - Four warning boards, extendable by approx. 400 mm, approx. 423 x 423 mm - Axle load gauge including load diagram - HRM (High Resistance Metallisation) metallization of the outer frame - Entire steel structure shot-blasted, then all defined visible surfaces hot-finished in metallisation with ZINACOR 850 (zinc 85% - aluminum 15%)