Faymonville 5-Achs-Doppel-Tele-Semi-Sattelauflieger nakup rabljenega (44.028)

Stanje: novo, lastna masa: 15.450 kg, največja dovoljena obremenitev: 65.550 kg, skupna masa: 80.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 21.900 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 925 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimized platform length, approx. 3,700 mm long, with rear tapering of approx. 1,000 mm x 10° Technical fifth wheel load: 30,000 kg. For tractors: 4x2, 6x2, and 6x4 Loading Platform: Double-extendable loading platform, approx. 8,800 mm long with rear taper of approx. 500 mm x 10°. A support table approx. 300 mm wide is welded to the central beam, featuring elongated slots at the front and rear for optional bridge elements that can be hooked in and repositioned Pneumatic locking with conical locking pin and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles and Tyres: BPW axles and suspension, first axle self-steering, all other axles hydraulically and mechanically forced-steered First axle equipped with an electro-magnetic reverse lockout, activated via reverse gear and manually. Technical axle load: 12,000 kg. Air suspension with lift and lower valve Manufacturer by our choice Sockets and Lighting: 24-volt lighting system in accordance with EU regulations Hjdjrigw Ropfx Akbonr ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Complete HRM metallizing Full steel construction, shot-blasted, then hot-finished with ZINACOR 850 Paintwork: 6-stage finishing process: Complete steel construction shot-blasted after welding 1 coat of zinc-based primer, 1 coat of adhesion primer. Final paintwork in 2 coats of 2K paint in single-tone DB 7350 Novagrau, followed by cavity sealing with special wax Accessories: Detachable front wall made of steel, approx. 400 mm high Connection strip for supply lines to the tractor unit, fitted at the height of the outer frame profile ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets. If your pin configuration deviates from the ISO connector standard, please inform us 3 kW electro-hydraulic power unit for hydraulic functions (excluding hydraulic winches) 1 pair of plug-in ALU sidewalls on the gooseneck, approx. 400 mm high, anodized finish 3.5'' king pin. Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide 2 wheel chocks with holder in front of the front wall Mechanical landing legs with 2-speed gearbox and crank Control valves for hydraulic ramps located on the right side of the vehicle 1 pair of mechanical rear supports Central lubrication system with 1 pump, BEKAMAX brand, using standard grease according to NLGI-2 Removable guard covering the pump(s) of the central lubrication system Remote steering from front and rear, controlled by cable remote with push buttons, with axle tracking control, no installation required on tractor unit Under the gooseneck and on the rear crossmember, one 7-pin socket with holder for warning signs each on left and right. One 7-pin socket on the rear crossmember Manual and documentation One-piece INOX stowage box, approx. 2,480 x 340 x 390 mm, straight design Please note that any special equipment and accessories will increase the unladen weight and correspondingly reduce the payload Warning package: 4 warning boards, approx. 423 x 423 mm, extendable by approx. 1,000 mm, incl. 2 LED position lights and brackets for beacon.

Stanje: novo, lastna masa: 15.420 kg, največja dovoljena obremenitev: 61.080 kg, skupna masa: 76.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading Platform: Extendable loading platform with rear chamfer approx. 500 mm x 8° 8 pairs of flip-out lashing rings 1 pair of recessed lashing rings at the front of the loading area Cutouts in the outer frame for securing straps Approx. 48 mm thick hardwood flooring; checker plate above the axles Two-Part Steel Ramps: One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering. Ramps with hydraulically folding ramp sections, hydraulic lifting and hydraulic lateral movement. Max load per pair: 50,000kg. Landing Legs: • JOST landing legs (mechanical) with two-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: BPW axles and suspension, 4th and 5th axle self-steering Technical axle load: 12,000 kg 4th and 5th axle with electromagnetically operated reverse lock, activated by reverse gear and manually Tyres: 235/75 R 17.5 3PMSF Brake System: Brake system according to EU regulations with EBS-E (4S3M) Sockets and Lighting: Electrical system according to EU standards, 24 Volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets Connections per ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component (2K) zinc-rich primer High-quality single-colour 2K topcoat in MB 7350 Novagrau Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Steel Structure: High-strength fine-grained steel construction Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Hodpfxel Sl Izs Akbenr Accessories: One spare wheel with holder in front of the front wall 2" king pin Galvanized steel front wall approx. 400 mm high Yellow-red air couplings on the galvanized front connection panel 2 wheel chocks with holder on the front wall Mounting at the rear of the gooseneck for ALU approach ramps Bracket for beacon at trailer rear Galvanized supports under sloped area of load floor White reflective tape per EU regulations on sides, extension, and red at the rear Electro-hydraulic unit under the rear of loading platform Warning sign brackets including sockets left/right on gooseneck and rear plate Control valves for ramps mounted right side of trailer Mudflap at rear of trailer Manual and documentation on USB stick 3.5" loose king pin supplied On gooseneck: ALU side boards and rear wall, plug-in approx. 2,440 x 400 mm (LxH) Removable rear galvanized stakes (Body length approx. 2,560 mm) 3 pairs WADER container pockets for 1x 20'/30' or 1x 40' container 6 pairs stake pockets for 100 x 50 mm plug-in stakes in outer frame Galvanized extensions, extendable by approx. 230 mm per side Lift axle on front axle, controlled via TEBS E according to actual axle load and current payload Square climbing strips 20 x 20 mm every 200 mm on outer frame chamfer of load floor Checker plate coverings above the king pin and loading area...

Stanje: novo, lastna masa: 15.900 kg, največja dovoljena obremenitev: 63.500 kg, skupna masa: 68.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 12.700 mm, širina tovornega prostora: 2.740 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75/r17,5, barva: siv, obratovalna teža: 52.100 kg, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimal load bed length, approx. 3,300 mm long, rear with taper approx. 1,000 mm x 10° Technical fifth wheel load: 23,000 kg For tractor units: 6x2, 6x4, and 8x4 Load bed: Extendable load bed, approx. 9,400 mm long with rear taper approx. 500 mm x 10° A recess in the load bed as well as in the tapering section for accommodating the excavator dipper stick, approx. 3,850 x 950 x 210/290 mm Pneumatic locking with conical locking bolt and reinforced locking positions, service lines are protected within the extendable beams and automatically adapt to the respective bed length Axles and Tires: BPW axles and suspension, 1st axle fixed, all other axles hydro-mechanically forced steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool 235/75 R 17.5 3PMSF twin tires Load index 143/141J (144/144F) Two-piece steel ramps: One pair of two-piece steel ramps, approx. 4,350 mm long and approx. 900 mm wide Hardwood covering Hydraulically folding ramp tips, each ramp hydraulically adjustable approx. 235 mm outward and approx. 215 mm inward Braking system: Braking system by WABCO EBS-E according to EU regulations Sockets and lighting: 24-volt lighting system Full metallization: Complete HRM metallization with ZINACOR 850 for optimal corrosion protection Surface treatment: Entire steel structure automatically blast cleaned with shot blasting after welding Second blasting treatment with corundum for optimal coating adhesion Final painting: 2 coats of 2-component paint in Novagrau, followed by sealing of cavities with special wax Rims in silver-grey Steel construction: Steel construction from high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Accessories: Plug-in steel front wall, approx. 400 mm high Connection rail for service lines to the tractor unit Spiral cable for supplying the electro-hydraulic unit and/or electric winch between trailer and tractor unit, with plug for the electro-hydraulic unit to control hydraulic operations, except for hydraulic winches Outer beam of gooseneck with mounting holes for bolted lashing rings First hole approx. 200 mm from the front, thereafter approx. every 400 mm One mounting hole in the rear upper area of the outer gooseneck beam for a bolted lashing ring Approx. 40 mm thick hardwood floor on the gooseneck, checker plate floor over the kingpin Guide plate on gooseneck for the fifth wheel plate, approx. 500 mm wide On the load bed, continuous and between the axles intermittent approx. 50 mm thick hardwood floor Load bed locking with conically welded locking profiles every 250 mm, including preload plate Slotted holes for attachable and movable bridging elements: on the fixed section behind the gooseneck at the front of the load bed 1 movable intermediate table for the extension tube with large cross-section Hedpsmfqi Isfx Akbonr Control valves for the hydraulic ramps on the right side of the vehicle Central lubrication system with 1 pump, standard grease according to NLGI-2 Radio remote control for steering operation, in addition to cable remote control, with 2 control lights on the receiver for single-track steering monitoring

Stanje: novo, lastna masa: 14.800 kg, največja dovoljena obremenitev: 61.700 kg, skupna masa: 76.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck with rear chamfer of approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Loading Platform: • Extendable loading platform with rear chamfer of approx. 500 mm x 8° • 9 pairs of folding external lashing rings • 1 pair of recessed lashing rings at the front of the loading platform • Cutouts in the outer frame of the loading platform for attaching tension belts • Approx. 48 mm thick hardwood flooring, checker plate above the axles Hsdpsma Hf Rjfx Akbsnr Landing Legs: • JOST mechanically operated landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: • BPW axles and suspension, 1st axle steering, 2nd and 3rd axle fixed, 4th and 5th axle follow-steering • Technical axle load: 12,000 kg • 1st, 4th, and 5th axles with electromagnetic reverse lock, activated via reverse gear or manually • Tyres: 235/75 R 17.5 3PMSF Brake System: • WABCO brake system in accordance with EU regulations including EBS-E (4S3M) Paintwork: • Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer • High-quality single-color two-component (2K) topcoat in MB 7350 Novagrau • Rear section metallized and painted in RAL 9010 (Pure White) Steel Construction: • Steel structure made from high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC (yield strength 355MPa) • S690QL/S700MC (yield strength 690MPa) Accessories: • One spare wheel with holder in front of the front wall • 2" king pin • Galvanized steel front wall, approx. 400 mm high • Front galvanized connection strip with yellow-red air couplings • 2 wheel chocks with holders mounted on the front wall • Rear mount on gooseneck for ALU drive-on ramps • Galvanized extendable wideners appx. 230 mm per side • Bracket for a beacon at the rear of the trailer • Galvanized supports under the chamfer of the loading platform • White reflector tape on the sides as per EU regulations, red at the extension and rear • Mounts for warning panels including socket left and right at the gooseneck and rear panel • Detachable ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • Rear galvanized plug-in stanchions removable (body length approx. 2,560 mm) • 3 pairs of WADER container pockets in the loading platform for a 20ft (30ft) or a 40ft container • 7 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform • Lifting axle on the front axle with TEBS E control according to the current axle load and loading condition • Movable mounting rails for ALU drive-on ramps at the rear of the vehicle • 20 x 20 mm square climbing strips at 200 mm intervals on the outer frame chamfer of the loading platform • BEKAMAX (Pico) centralized lubrication system with NLGI-2 standard grease and removable pump cover • Four extendable warning panels approx. 423 x 423 mm with a position light, extendable by approx. 400 mm • Holder for beacon mounted on the warning panels • European reflector plates (red-yellow) on the rear of the trailer • 80 km/h speed limit stickers at rear and both sides • Axle load gauge with load diagram included • HRM Metallisation (High Resistance Metallisation) of the outer frame • Complete steel structure is shot-blasted, then defined visible surfaces are metallized with ZINACOR 850 (zinc 85% - aluminum 15%) using hot finishing

Stanje: rabljeno, lastna masa: 10.600 kg, največja dovoljena obremenitev: 39.400 kg, skupna masa: 50.960 kg, konfiguracija osi: 3 osi, prva registracija: 09/2024, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5, barva: siv, Leto izdelave: 2024, obratovalna teža: 10.600 kg, Oprema: ABS, Vrat: -Vrat z oblogo prevleko iz trdega lesa, debeline 30 mm -Vrat na zadnji strani v ravni izvedbi -3 pari zateznih obročev (LC 5.000 daN) Nakladalna površina z izvlečno izvedbo: -Nakladalna površina z izvlečno izvedbo -5 parov zateznih obročev, ki se zunanje odklapljajo (LC 5.000 daN) -3 pari zateznih obročev, ki se zunanje odklapljajo (LC 10.000 daN) -1 par zateznih obročev, nameščen vodoravno spredaj na nakladalni površini (LC 10.000 daN) -Izrezi na zunanjem okvirju nakladalne površine za pritrditev zategovalnih pasov (LC 2.000 daN) -Obloga iz trdega lesa, debeline približno 48 mm; nad osmi je prevleka iz valjane pločevine Podpora sedla: -JOST podpore sedla (mehanske) z 2-stopenjskim menjalnikom za 24 t nosilnosti (5 t testna nosilnost) Osi in pnevmatike: -BPW osi, dve fiksni osi, dve sledilni osi -Zračna vzmet, z bobnasto zavoro, z funkcijo dviganja/spuščanja -Sledilne osi z elektromagnetično blokado za vožnjo v vzvratno smer, ki se aktivira preko vzvratnega prestave ali ročno -Pnevmatike 205/65 R17.5 Zavorna naprava: -Zavorna naprava v skladu z uredbami EU, z EBS-E (4S3M) Jeklena konstrukcija: -Jeklena konstrukcija iz visoko trdnih finozrnatih jekel -Vrste jekel: -S355J2+N/S355MC (meja tečenja 355 MPa) -S690QL/S700MC (meja tečenja 690 MPa) Električna napeljava: -Električna napeljava v skladu z uredbami EU, razsvetljava 24 voltov, ASPÖCK-NORDIK (ASS3) -ASPÖCK-UNIBOX na priključni letvi spredaj s vtičnicami 24N, 24S in 15-polno -Barvanje: -Prvo razredna in dolgotrajna protikorozijska zaščita standardno peskane varjene konstrukcije je zagotovljena z dvokomponentnim (2K) cinkovo-prašnim temeljnim premazom -Visokokakovosten dvokomponentni (2K) končni premaz, enobarvni, v barvi Novagrau Vključena dodatna oprema: -En rezervni zračniški kolo z nosilcem pred čelno steno -2" kraljeviče -En pocinkana jeklena čelna stena, približno 400 mm visoka -Na pocinkani priključni letvi spredaj rumeno-rdeče zračne spojke -4 kosi klinih z nosilcem na čelni steni -Pocinkane zložljive podpore pod poševnino nakladalne površine -Nosilec za rotacijsko luč na zadnji strani prikolice -Podaljški, pocinkani, izvlečni za približno 230 mm na vsaki strani -Bel refleksni trak v skladu z uredbami EU, na strani, na izvlečni površini in zadaj rdeč -Na vratu in na zadnji plošči na levi in desni strani po en nosilec za opozorilne table, vključno z vtičnico -En odbijač blata na zadnji strani prikolice -Evropski odsevni znaki (rdeče-rumeni) na zadnji strani prikolice -Priročnik in navodila na USB pomnilniku -Sistem za nadzor tlaka v pnevmatikah (TPMS) v skladu z ECE R 141 -Na vratu aluminijaste stranske stene in zadnja stena, ki se vstavi, približno 2.440 x 400 mm -Zadnje, pocinkane vstavne ograje so odstranljive, dolžina nadgradnje je približno 2.560 mm -7 parov držal za kontejnerje WADER -1 x 20-čevlni kontejner na nakladalni površini; 1 x 40-čevlni kontejner na nakladalni površini; 1 x 40-čevlni kontejner nad vratom; 2 x 20-čevlni kontejner -7 parov držal za ograje za vstavne ograje 100 x 50 mm na zunanjem okvirju nakladalne površine -Dvižna os na sprednji osi z nadzorom preko TEBS E, odvisno od trenutne obremenitve osi in trenutnega stanja obremenitve Hnedjw Adkxepfx Akber -Premikajoča se letva za pritrditev aluminijastih plošč na zadnji strani vozila -Na valjani pločevini na vratu in na nakladalni površini prevleka iz peska kot zaščita pred zdrsom -Štiri opozorilne table, ki se približno za 400 mm izvlečejo, približno 423 x 423 mm, z pozicijsko lučjo -Na opozorilnih tablah nosilec za

Stanje: rabljeno, lastna masa: 10.350 kg, največja dovoljena obremenitev: 37.650 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 10/2018, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 245/70 R 17,5, barva: oranžna, Leto izdelave: 2018, obratovalna teža: 10.350 kg, Oprema: ABS,

Stanje: novo, lastna masa: 15.550 kg, največja dovoljena obremenitev: 47.450 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimization of loading platform length, length approx. 3,700 mm - Rear gooseneck with bevel approx. 1,000 mm x 10° Loading Platform: - Extendable loading platform, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° - A recess in the loading platform as well as into the bevel for accommodating the excavator dipper stick - Pneumatic locking with conical locking bolts and reinforced lock positions - Hardwood covering on the loading platform bevel Ramps: - 1 pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm - Ramps with hardwood covering - Hydraulically folding ramp tips - Ramps can be hydraulically shifted individually approx. 235 mm outward and approx. 215 mm inward - Square climbing cleats 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, 1st axle lift-steered, all other axles forced-steered with hydromechanical system - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with raising and lowering valve - Tyres 235/75 R 17.5, twin tires - TPMS tire monitoring system compliant with ECE R141 - TPMS sensors installed in all wheels including spares Accessories included: - Removable steel front wall, approx. 400 mm high - 3kW electro-hydraulic power pack for hydraulic operations, excluding hydraulic winches - Parking position on gooseneck for warning boards when not in use - 1 spare wheel - On the gooseneck: 1 pair of removable side aluminium drop sides, approx. 400 mm high, anodised - On the gooseneck: 1 removable rear aluminium drop side, approx. 400 mm high, anodised - Above the gooseneck: approx. 40 mm thick hardwood floor, chequer plate above king pin - 2" king pin - Guide plate on gooseneck for fifth wheel, approx. 500 mm wide - 4 wheel chocks - Mechanical landing gear with 2-speed gearbox and crank Hnodpfx Akek Aht Ujber - JOST Modul B – static test load = 50,000 kg - 1 intermediate table, approx. 300 mm wide - Extensions (galvanised) extendable by approx. 230 mm per side - Wheel recesses with square climbing cleats - ALU covers for the wheel recesses - 1 pair of mechanical rear supports - Remote steering at front and rear via cable remote control, with single track monitoring of axles - 1st axle with automatic lift axle function - Central lubrication system with 1 BEKAMAX brand pump - Radio remote control for remote steering, additionally to cable remote, with 2 indicator lights on the receiver as single track monitoring - Wabco Smart Board System - 4 warning boards, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for revolving beacon

Stanje: novo, lastna masa: 10.700 kg, največja dovoljena obremenitev: 38.800 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17,5, barva: sivo-črna, Oprema: ABS, Gooseneck: • Gooseneck with front corners beveled at 45° and rear taper approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Extendable loading platform: • Loading platform in extendable design with rear taper approx. 1,000 mm x 8° • Cut-outs in outer frame of loading platform for attaching tensioning straps • Approx. 48 mm thick hardwood flooring; anti-slip checker plate covering above the axles Two-piece steel ramps: • One pair of galvanized, two-piece steel ramps with approx. 48 mm thick hardwood covering • Ramps with hydraulically foldable ramp sections, hydraulic lift system, and hydraulically adjustable • Maximum load per pair: approx. 40,000 kg Axles and tires: • BPW axles and suspension, 2 rigid axles, 1 self-steering axle • Technical axle load: 12,000 kg • Electromagnetic reverse lock, activated via reverse gear or manually • Air suspension with lift and lower valve • Axle tools • 235/75 R 17.5 3PMSF Braking system: • WABCO braking system according to EU regulations with EBS-E Paintwork: • First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component zinc dust primer • High-quality, single-color top coat in MB 7350 Novagrey applied with two-component paint • Rear section metallized and painted in RAL 9010 Landing legs: • JOST landing legs with 2-speed gearbox for 24t lifting load (50t test load) Steel construction: • Steel construction made of high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC • S690QL/S700MC Electrical system: • Electrical system in accordance with EU regulations, 24 Volt lighting • ASPÖCK-UNIBOX on front connection panel with 24N, 24S & 15-pin sockets Accessories included: • One spare wheel with holder Hjdpfx Aehlz S Nskbonr • Galvanized steel front wall approx. 400 mm high • Yellow-red air couplings on the galvanized front connection panel • 4 wheel chocks • Rear mounting bracket for beacon light at the end of the semitrailer • Recess at rear of gooseneck for ALU approach ramps • Galvanized folding supports under the loading platform taper • Cover plates to bridge the gap between ramps and loading platform • White reflector tape per EU regulations on sides, extension, and red at rear • Electro-hydraulic unit at rear, under the loading platform • On gooseneck and ramps, left and right, each with a holder for warning signs, including socket • Operating valves for the ramps located on the right side of the trailer • ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) • Four warning panels extendable by approx. 400 mm with a position light • 3 pairs of WADER container pockets in the loading platform for one 20ft, 30ft or 40ft container • 6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading platform • Galvanized extensions, extendable by approx. 230 mm per side • 20 x 20 mm square climbing strips every 200 mm on the outer frame of the platform taper • Painted anti-slip sand layer on checker plates, above king pin and loading platform • Load gauge for axle load measurement, including load diagram • HRM metallization (High Resistance Metallisation) of the outer frame • Complete steel construction shot-blasted, then defined visible surfaces metallized and hot-finished with ZINACOR 850 (Zinc 85% - Alu 15%)

Stanje: novo, lastna masa: 11.000 kg, največja dovoljena obremenitev: 38.500 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm hardwood flooring Load Area: - Extendable loading area with rear taper approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses fitted with square climbing strips 15 x 15 mm, including lower extensions - Between the 1st and 2nd axle, a pair of fixed wheel recesses with cover, approx. 1,610 x 970 x 400 mm - Recess in the bevel as well as protruding into the loading area for parking excavator dipper stick approx. 2,900 x 750 x 210/290 mm - 1 pair of lashing rings, installed flat at the front of the load area (LC 10,000 daN) - 5 pairs of folding lashing rings on the outside (LC 5,000 daN) - 2 pairs of folding lashing rings on the outside (LC 10,000 daN) - 2 pairs of lashing rings in the dipper stick recess (LC 5,000 daN) - Cut-outs in the outer frame of the load area for securing straps (LC 2,000 daN) - Incl. three-part removable galvanized covers over the wheel recesses – max. point load 3.5 t / pc. Two-piece Steel Ramps: - One pair of galvanized, two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood surfacing - Ramp with hydraulically folding ramp sections, hydraulic lifting gear, and hydraulically adjustable Axles and Tyres: - BPW axles and suspension, 2 rigid axles, 1 steering trailing axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lifting and lowering valve - Axle tool kit - Tyres 235/75 R 17.5 - TPMS tyre pressure monitoring system in accordance with ECE R 141 Accessories Included: - Mounts for warning signs left and right at the gooseneck and at the rear, each with socket - One spare wheel - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings at the galvanized front connector strip - 4 wheel chocks - Galvanized, extendable outriggers approx. 230 mm per side - Galvanized folding supports beneath the loading area bevel - Rear trailer bracket for rotating beacon - Cover plates for bridging the gap between ramps and load area - White reflective tape to EU regulations, sides and on extensions; rear in red - Electro-hydraulic unit installed at the rear beneath the loading area - Ramp control valves mounted on right trailer side - European reflective panels (red-yellow) on rear of trailer - Four extendable warning boards, approx. 423 x 423 mm, with position light - Bracket for rotating beacon on warning boards - Removable ALU side boards and rear board on gooseneck approx. 2,440 x 400 mm - Rear galvanized removable stakes (structure length approx. 2,560 mm) - 2 pairs of WADER container pockets in loading area for 20ft or 30ft container - 3 pairs of socket pockets for stakes 100 x 50 mm in outer frame of loading area - Removable, galvanized intermediate table with 1 pair of WADER container pockets Hjdpfeup U Hzsx Akbenr - Square climbing strips 20 x 20 mm spaced every 200 mm on outer frame at loading bevelling - Painted sand layer on chequer plates of the gooseneck and loading area for anti-slip protection - 80 km/h speed stickers rear and both sides - Load manometer for axle load measurement, including load chart.

Stanje: novo, lastna masa: 13.500 kg, največja dovoljena obremenitev: 51.500 kg, skupna masa: 69.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimizing loading platform length, length approx. 3,700 mm Gooseneck rear with chamfering approx. 1,000 mm x 10° Loading Platform: Telescopic loading platform, length approx. 8,800 mm, with rear chamfering approx. 500 mm x 10° Recess in the chamfer as well as into the loading platform to accommodate the excavator dipper stick Hsdpsk Ahugefx Akbonr Pneumatic locking with conical pin and reinforced locking positions Supply lines routed protected within the extendable beam, adapting to the respective platform length Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps individually adjustable hydraulically approx. 235 mm to the outside and approx. 215 mm to the inside Axles and Suspension: BPW axles and suspension, two rigid axles, two steering trailing axles Electromagnetic reverse lock, activated via reverse gear and manually Air suspension with lift and lower valve Axle tool Tyres: 235/75 R17.5 3PMSF twin tyres Load index: 143/141J (144/144F) Brake System: WABCO braking system, EBS-E in accordance with EU regulations Lighting System: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Metalizing: Standard HRM metallization of the outer frame Complete steel structure shot-blasted, then visible defined surfaces metallized with ZINACOR 850 (Zinc 85% - Alu 15%) hot-refined Steel Construction: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified as per DIN-EN 287-1 MAG welding process according to EN ISO 4063 Shielding gas M21 as per EN ISO 14175 Accessories Included: Front wall made of steel, plug-in, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin 24N connection per ISO-11852, 24S connection per ISO-3731, 15-pin connection per ISO-12098 Round NATO socket on the front connection strip Cable to supply electro-hydraulic unit and/or electric winch (35 mm², 3.5 m long) between trailer and tractor with connector (NATO-NATO) 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches 1 spare wheel with mounting adapter Outer beam of the gooseneck with fastening holes for screwable lashing rings. The first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included One fastening hole in the rear upper area of the gooseneck's outer beam for a screwable lashing ring 1 pair of screw-in lashing rings Approx. 40 mm thick hardwood covering above the gooseneck On the gooseneck, 1 pair of plug-in side aluminium walls, approx. 400 mm high, anodized On the gooseneck, a plug-in aluminium rear wall, approx. 400 mm high, anodized 2" kingpin Gooseneck guide plate for fifth wheel, approx. 500 mm wide 4 wheel chocks with holder Holder for aluminium approach ramps Mechanical landing gear with 2-speed gearbox and crank Continuous hardwood floor approx. 50 mm thick on the loading platform, interrupted between axles Platform locking with conically welded locking profiles every 250 mm incl. tension plate Slotted holes at the front of the loading platform for attachable and adjustable bridging elements 1 intermediate table with recessed platform, approx. 300 mm wide for the draw-out tube with large cross-section, with sheet metal covering Front and rear with slotted holes

Stanje: novo, lastna masa: 13.250 kg, največja dovoljena obremenitev: 47.550 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, vzmetenje: zrak, velikost pnevmatike: 245/70 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings 30 mm thick hardwood flooring Extendable loading platform: Loading platform in extendable design with rear chamfer approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings 3 pairs of outward-folding lashing rings 1 pair of flat lashing rings at the front of the loading area Cut-outs in the outer frame of the loading area for inserting tension straps Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Two-part steel ramps: One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering. Ramp with hydraulically folding and unfolding parts, hydraulic lifting system, and hydraulically adjustable position. Maximum load per pair: 40,000 kg Landing legs: JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced-steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool Tires 245/70 R 17.5 Braking system: Braking system according to EU regulations with EBS-E (4S3M) without connecting lines to tractor unit Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: Hnsdpjl Uxdkofx Akbor S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer High-quality one-color two-component (2K) top coat in Novagrau Rear section metallized and painted in RAL 9010 (pure white) Metallic paint not possible Electrical system: Electrical system according to EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connections conforming to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" kingpin One galvanized steel headboard approx. 400 mm high At the galvanized front connection strip, yellow-red air couplings 4 wheel chocks with holders at the headboard One spare wheel with holder in front of the headboard Electro-hydraulic power unit Rear and front remote steering via cable remote control with push-buttons, with single-track control of the axles Bracket at rear of gooseneck for ALU drive-on ramps European reflector signs (red-yellow) at trailer rear White reflective tape according to EU regulations at the sides, at the extension, and red at the rear At the gooseneck and on the ramps left and right, each with a holder for warning signs including socket One holder for beacon at trailer rear Galvanized folding supports under the loading platform chamfer Ramp operating valves fitted on the right side of the trailer Cover plates to bridge the gap between ramps and loading platform One mudflap at trailer rear Manual and description on USB stick Central lubrication system BEKAMAX (Pico) with general-purpose grease NLGI-2 and removable pump guard On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm The rear galvanized stakes are removable, superstructure length approx. 2,560 mm One INOX toolbox 1,350 x 400 x 400 on the gooseneck, box covers oil filler cap 4 pairs of WADER container pockets in the loading area for a

Stanje: novo, največja dovoljena obremenitev: 49.000 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with front corners chamfered at 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Extendable Loading Platform: - Loading platform, extendable design with rear chamfer of approx. 1,000 mm x 8° - 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) - 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - 1 pair of horizontal lashing rings at the front of the loading platform (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for securing straps (LC 2,000 daN) - Hardwood flooring approx. 48 mm thick, checker-plate covering above the axles Two-Part Removable Ramps: - One pair of galvanized two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp sections, hydraulic lifting mechanism, and hydraulic side-shift - Maximum load per pair: 40,000 kg Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Axles and Tyres: - BPW axles, two fixed axles and two steering axles (self-steering), air suspended, with drum brakes, raise/lower function - Self-steering axles with electro-magnetic reverse lock, can be activated by reverse gear or manually - Axle tool kit - Tyre size 235/75 R 17.5 Brake System: - Braking system according to EU regulations with EBS-E (4S3M) Steel Structure: - Steel structure made of high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Paintwork: - First-class, long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component (2K) zinc dust primer - High-quality single-tone topcoat using 2-component (2K) paint in Nova grey Hsdpeh Etf Rsfx Akbonr Electrical System: - Electrical system according to EU regulations, 24 volt lighting, ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX on the front connector strip with 24N, 24S, and 15-pin sockets Included Accessories: - 2" kingpin - Galvanized steel front wall, approx. 400 mm high - One spare wheel with holder in front of the headboard - Yellow-red air couplings on the galvanized front connector strip - 4 wheel chocks with holders on the front wall - Mount at the rear section of the gooseneck for ALU approach ramps - Galvanized folding supports underneath the loading platform chamfer - One holder for warning beacon - Cover plates to bridge the gap between ramps and loading platform - White reflective tape on the side, red on extension and rear, according to EU regulations - Electro-hydraulic power unit - At the gooseneck and ramps (left/right) a holder each for warning signs including socket - Control valves for the ramps mounted on the right side of the trailer - One mud flap at the rear of the trailer - Manual and documentation on USB stick - On the gooseneck, plug-in ALU side boards and rear wall approx. 2,440 x 400 mm - Rear galvanized plug-in stakes are removable (body length approx. 2,560 mm) - 4 pairs of WADER container pockets in the loading platform for one 20ft, two 20ft or one 40ft container - 7 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading platform - Galvanized, extendable platform wideners approx. 230 mm per side - Lift axle on the front axle with control system - 20 x 20 mm square climbing bars - BEKAMAX central lubrication system - Four warning signs extendable by approx. 400 mm eac

Stanje: novo, lastna masa: 10.600 kg, največja dovoljena obremenitev: 39.400 kg, skupna masa: 50.960 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5, barva: siv, obratovalna teža: 10.600 kg, Oprema: ABS, Gooseneck: - Gooseneck with 30 mm hardwood flooring - Gooseneck at rear in straight version - 3 pairs of lashing rings (LC 5,000 daN) Extendable load floor: - Load floor in extendable configuration - 5 pairs of lashing rings foldable outward - 3 pairs of lashing rings foldable outward - 1 pair of lashing rings laying at the front end of the load floor - Cut-outs in the outer frame of the load floor for attaching tension straps - Approx. 48 mm hardwood flooring, checker plate covering above the axles Landing legs: - JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tyres: - BPW axles, two rigid axles, two self-steering axles - Air suspension with drum brakes, with lift/lower function - The self-steering axles are equipped with an electromagnetically operated reverse lock, which can be activated via reverse gear or manually - Axle tools - Tyres 205/65 R17.5 Brake system: - Brake system compliant with EU regulations with EBS-E (4S3M) Steel structure: - Steel construction made from high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system in accordance with EU regulations, lighting 24 Volt, ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets - Connections according to ISO: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Paintwork: - High-quality and durable corrosion protection on the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer - High-quality single-colour 2-component (2K) top coat in Novagrau - Rear section metallised and painted in RAL 9010 (Pure White) Included accessories: - One spare wheel with holder in front of the bulkhead - 2" king pin - Galvanised steel front wall approx. 400 mm high - Yellow-red air couplings on the galvanised connection bar at the front Hnedpfx Ajt Ag Uwjkbor - 4 wheel chocks with holder at the front wall - Galvanised folding supports under the load floor slope - Holder for a warning beacon at the rear of the trailer - Galvanised extensions, extendable by approx. 230 mm per side - White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear - On the gooseneck and rear panel, left and right, one bracket each for warning panels including socket - European reflective markings (red-yellow) at the rear of the trailer - TPMS tyre pressure monitoring system according to ECE R 141 - On the gooseneck, plug-in ALU side walls and rear wall, approx. 2,440 x 400 mm - The rear, galvanised plug-in side stanchions are removable, length of the body approx. 2,560 mm - 7 pairs of WADER container pockets - 1x 20ft container on the load floor; 1x 40ft container on the load floor; 1x 40ft container above the gooseneck; 2x 20ft container - 7 pairs of stanchion sockets for plug-in stanchions 100 x 50 mm in the outer frame of the load floor - Lift axle on the front axle with control via TEBS E, depending on the current axle load and load condition - Sliding plug-in rail for ALU loading ramps at the rear of the vehicle - Anti-slip sand finish painted on the checker plates on the gooseneck and load floor - Four warning boards extendable by approx. 400 mm, approx. 423 x 423 mm, each with a position lamp - Holder for warning beacon on the warning boards - 80 km/h speed stickers at the rear and on both sides - Axle load gauge for determination of axle loads inclu

Stanje: novo, lastna masa: 22.700 kg, največja dovoljena obremenitev: 79.300 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 11.000 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 920 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 22.700 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize load platform length, approx. 3,750 mm long, rear with chamfer approx. 850 mm x 10° - Hydraulically liftable and lowerable, stroke ± 250 mm including hydraulic connection linked to the hydraulic axle compensation of the first two axles - Open in the rear third Hsdpfxek Af Sve Akbenr - For tractor units: 6 x 4 and 8 x 4 Load platform: - Extendable load platform, approx. 11,000 mm long with rear chamfer approx. 500 mm x 10° - Recess in the platform and into the chamfer for receiving the excavator dipper stick, approx. 4,240 x 900 x 440 mm - Pneumatic locking with conical locking pin and reinforced locking positions, supply lines protected within the extendable beams, automatically adapting to the actual platform length Ramps: - One pair of two-piece steel ramps approx. 4,650 mm long and 900 mm wide - Hydraulically foldable ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 215 mm inward - 25 mm "Super Grip" rubber flooring and approx. 5 mm checker plate as additional reinforcement on the chamfered section of the platform - Square climbing strips 20x30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, Suspension, and Tires: - PA-X axle system, all axles hydro-mechanically forced steered - Steering performance of the first two axles can be optimally adjusted to the platform length, both mechanically and hydraulically - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-fitted locking pins for securing in raised position - 245/70 R 17.5 3PMSF Accessories included: - Plug-in steel front wall, approx. 400 mm high - Supply line connection strip for tractor unit, mounted at the height of the outer frame profile - 1 spare wheel - Outer beams of gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from front, then every approx. 400 mm - 2 pairs of screw-in lashing rings included - Chequer plate covering over the gooseneck - On gooseneck: 1 pair of removable anodized ALU side walls, approx. 400 mm high - On gooseneck: 1 removable anodized ALU rear wall, approx. 400 mm high - 3.5" king pin / 2" king pin mounted - Guide plate of the gooseneck for fifth wheel plate, approx. 500 mm wide - 4 chocks - 4 axle load gauges - Mechanical drop tube supports at the front - 1 one-piece INOX toolbox, approx. 2,480 x 340 x 390 mm - Mechanical drop tube supports at the front - Continuous steel deck with baked-in sand layer as anti-slip protection on the platform - 1 intermediate table, approx. 500 mm wide, for the extension, with slotted holes for insertable and relocatable bridging elements - Sand coating on support surfaces of the intermediate table - Mechanical locking for securing the intermediate table on the extension - 8 pairs of stake pockets in the outer frame - Extendable (galvanized) widenings, approx. 230 mm per side - 1 pair of hydraulic rear supports - Central lubrication system - 1 reversing spotlight each on left and right rear of the vehicle - 3 kW electro-hydraulic power unit - Loose widening planks in reinforced steel U-frame - Radio and cable remote control - 4 warning signs, approx. 423 x 423 mm

Stanje: novo, največja dovoljena obremenitev: 38.800 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5 3PMSF, barva: siv, Oprema: ABS, Swan neck: - Swan neck with front corners beveled at 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm hardwood flooring Extendable load area: - Extendable load area with rear chamfer approx. 1,000 mm x 8° - 6 pairs of fold-out lashing rings (LC 5,000 daN) - 3 pairs of fold-out lashing rings (LC 10,000 daN) - 1 pair of flat lashing rings at the front of the load area (LC 10,000 daN) - Cut-outs in the external frame of the load area for attaching lashing straps (LC 2,000 daN) - Approx. 48 mm hardwood flooring, over the axles with checker plate covering Axles and Tires: - BPW axles and suspension, 2 fixed axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated by reverse gear or manually - Air suspension with lifting and lowering valve - Axle tools Hedpfx Aeuqlmnekbonr - 235/75 R 17.5 tires, 3PMSF Braking system: - WABCO braking system as per EU regulations with EBS-E (2S2M) Landing legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Accessories included: - One spare wheel with holder in front of the front wall - 2'' king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection rail - 4 wheel chocks with holder at the front wall - Rear light bracket at the rear of the trailer - Mounting points at the rear area of the swan neck for ALU loading ramps - Galvanized folding supports under the chamfer of the load area - Cover plates to bridge the gap between ramps and load area - White reflective tape according to EU standards on the sides, red at the extension and rear - Electro-hydraulic unit at the rear, under the load area - Bracket for warning panels left and right on the swan neck and ramps, including power socket - Ramp control valves mounted on the right-hand side of the trailer - One mud flap at the rear of the trailer - Manual and documentation on USB stick - On the swan neck aluminum side walls and rear wall, approx. 2,440 x 400 mm - The rear galvanized stakes are removable (body length approx. 2,560 mm) - Four warning panels extendable by approx. 400 mm, size approx. 423 x 423 mm, with position light - 3 pairs of WADER container pockets in the load area for a 20ft, 30ft, or 40ft container - 6 pairs of stake pockets 100x50 mm in the external frame of the load area - Galvanized extensions, extendable by approx. 230 mm per side - Square climbing strips 20 x 20 mm every 200 mm on the outer frame of the chamfered area of the load area - Anti-slip sand layer painted on the checker plate above the king pin and load area - Mounting for beacon on the warning panels - European reflective plates (red-yellow) at the rear of the trailer - 80 km/h speed stickers at the rear and on both sides - Load gauge for determining axle loads, including load chart - HRM metallization (High Resistance Metallisation) of the external frame - Complete steel construction shot-blasted, then the defined visible surfaces finished hot-metallized with ZINACOR 850 (zinc 85% - aluminum 15%)

Stanje: novo, lastna masa: 10.350 kg, največja dovoljena obremenitev: 39.150 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Loading area: Hedoiu Er Aspfx Akbenr - Telescopic loading area with rear chamfer approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm - Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom - Between the 1st and 2nd axle, 1 pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm - 3-piece detachable galvanized covers over the wheel recesses (W 670 mm) – max. point load 5 t / pc. - Recess in the chamfer and protruding into the loading area for the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of foldable external lashing rings (LC 5,000 daN) - 2 pairs of foldable external lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) - Cutouts in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) One-piece aluminum ramps: - 1 pair one-piece ALU ramps, approx. 2,500 x 600 mm - Ramp with spring lifting mechanism and manually adjustable - Maximum load per pair: 24,000 kg Axles and tires: - BPW axles and suspension, 2 rigid axles, 1 trailing steering axle - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tyres 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 Accessories included: - 1 spare wheel with holder in front of the bulkhead - 2" kingpin - 1 galvanized steel front wall approx. 400 mm high - At the galvanized coupling rail at the front, yellow-red air couplings - 4 wheel chocks with holder at the bulkhead - Mounting point at the rear of the gooseneck for ALU ramps - Galvanized extensions, extendable by approx. 230 mm per side - Galvanized folding supports under the chamfer of the loading area - 1 holder for a rotating beacon at the rear of the trailer - White reflective tape laterally, at the extension, and red at the rear, per EU regulations - At the gooseneck and rear panel, left and right, each with a holder for warning signs including socket - On the gooseneck, plug-in ALU sideboards and rear wall, approx. 2,440 x 400 mm - The rear galvanized stakes are removable (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container - 3 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area - 1 removable galvanized intermediate table with 1 pair of WADER container pockets - 20 x 20 mm square climbing strips every 200 mm on the outer frame in the chamfer of the loading area - Anti-slip sand coating on the checker plates on the gooseneck and the loading area - Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with position light - Holder for rotating beacon on the warning signs - 80 km/h speed stickers at the rear and on both sides - Load gauge for determining axle loads including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then all defined visible surfaces metalized and hot-finished with ZINACOR 850 (Zinc 85% – Alu 15%)

Stanje: novo, lastna masa: 9.300 kg, največja dovoljena obremenitev: 30.100 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, Oprema: ABS, Labod: •Labod z zadnjo nagnjenostjo približno 750 mm x 10° •3 pari pritrdilnih obročev (nosilnost 5.000 daN) •Prevleka iz trdega lesa, debeline 30 mm Nosilna površina z možnostjo podaljšanja: •Nosilna površina z možnostjo podaljšanja in zadnjo nagnjenostjo približno 1.000 mm x 8° •5 parov pritrdilnih obročev, z možnostjo obračanja navzven (nosilnost 5.000 daN) •3 pari pritrdilnih obročev, z možnostjo obračanja navzven (nosilnost 10.000 daN) •1 par pritrdilnih obročev, nameščenih vodoravno na sprednji strani nosilne površine (nosilnost 10.000 daN) •Izrezi na zunanjem okvirju nosilne površine za pritrditev zategovalnih trakov (nosilnost 2.000 daN) •Prevleka iz trdega lesa, debeline približno 48 mm, nad osmi protizdrsna prevleka Osi in pnevmatike: •Os BPW, hidravlično-mehanski sistem usmerjanja •Največja dovoljena obremenitev osi: 12.000 kg •Zračna vzmet z ventilom za dvigovanje in spuščanje •Sistem za nadzor tlaka v pnevmatikah TPMS, v skladu s standardom ECE R 141 Hedpfezr Egdsx Akbsnr •Pnevmatike 235/75 R17.5 3PMSF Barvanje: •Celotna jeklena konstrukcija je po varjenju obdelana s peskanjem v avtomatski napravi •Drugo peskanje s korundom za optimalno oprijemljivost prevleke •HRM-metalizacija celotnega šasija vozila s premazom ZINACOR 850 (85 % cink/15 % aluminij) za zagotovitev najboljše zaščite pred korozijo •Končni premaz z 2 slojema 2K lak, enobarven v barvi DB 7350 Novograu •Zadnji del je metaliziran in pobarvan v barvi RAL 9010 (čista bela) •Test barvanja je bil izveden v testu s solno prho po standardu ISO 9227-NSS •Zapiranje votlin s posebnim voskom Električna instalacija: •Električna instalacija v skladu s predpisi EU, osvetlitev 24 voltov ASPÖCK-NORDIK (ASS3) •Vse stranske markerice utripajo skupaj s smerniki •ASPÖCK-UNIBOX na priključnem panelu spredaj, z vtičnicami 24N, 24S in 15-polno •Dodatna oprema: •2" kraljevi člen •Ena pocinkana jeklena sprednja stena, približno 400 mm visoka •Na pocinkani priključni plošči spredaj, rumeno-rdeče zračne spojke •2 kosov zavornega klina z nosilcem na sprednji steni •Ena rezervna pnevmatika z nosilcem pred sprednjo steno •Elektro-hidravlična agregat •Pomožno krmiljenje, upravljanje od spredaj in zadaj s kabelskim daljinskim upravljalnikom prek gumbov, z nadzorom sledenja osi •Evropske odbijajoče table (rdeče-rumene) na zadnji strani prikolice •Bela odbijajoča trakovi v skladu s predpisi EU, nameščeni ob strani in na podaljšku, zadaj rdeče •Na labodu in zadnji strani, na levi in desni strani, po en nosilec za opozorilne table, vključno z vtičnico •Drseča priključna letev za aluminijaste rampe na zadnji strani vozila •Pocinkane zložljive opore pod nagnjenostjo nosilne površine •En ščitnik proti umazaniji na zadnji strani prikolice •Priročnik in opis •Centralni sistem mazanja BEKAMAX (Pico) z normalno mastjo NLGI-2 in odstranljivim pokrovom okoli črpalke •Na labodu so aluminijaste bočne stene in zadnja stena, ki se lahko vstavijo, približno 2.440 x 400 mm •Zadnje, pocinkane vstavne okvirje je mogoče odstraniti (dolžina nadgradnje približno 2.560 mm) •3 pari WADER-jevih žepov za kontejnerje na nosilni površini za 1x 20-ft, 1x 30-ft ali 1x 40-ft kontejner •6 parov žepov za okvirje za vstavne okvirje 100 x 50 mm v zunanjem okvirju nosilne površine •Ena orodjarna omara INOX 1.500 x 390 x 810 pod nosilno površino, na desni strani v smeri vožnje •Štirje opozorilni znaki, ki se lahko iztegnejo za približno 400 mm, približno 423 x 423 mm z pozicijsko lučjo •Radiokrmiljenje za pomožno krmiljenje, poleg kabelskega daljins

Stanje: novo, lastna masa: 9.300 kg, največja dovoljena obremenitev: 30.100 kg, skupna masa: 39.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, Oprema: ABS, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm hardwood flooring Extendable loading platform: - Loading platform, extendable execution with rear bevel approx. 1,000 mm x 8° - 5 pairs of folding external lashing rings (LC 5,000 daN) - 3 pairs of folding external lashing rings (LC 10,000 daN) - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - Cutouts in the outer frame of the platform for attaching tie-down straps (LC 2,000 daN) - Hardwood flooring approx. 48 mm thick, over the axles with checker plate covering Landing legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Axles and tyres: Hedpfx Asyxc Eyjkbsnr - BPW axles, hydro-mechanically forced steering - Technical axle load: 12,000 kg - Air suspension with raise/lower valve - Axle tool kit - TPMS tyre pressure monitoring system according to ECE R 141 - Tyres: 235/75 R17.5 3PMSF Accessories included: - 2" kingpin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection strip - 2 wheel chocks with holder on the front wall - One spare wheel with holder in front of the front wall - Electro-hydraulic unit - Rear axle steering, operable from front and rear via cable remote control with push buttons, with axle single-track monitoring - European reflective warning plates (red-yellow) at the rear of the trailer - White reflective tape according to EU regulations on the sides and on the extension, red at the rear - Gooseneck and rear left and right brackets for warning signs, including socket - Sliding hook-in bar for ALU loading ramps at the rear of the vehicle - One bracket for a rotating beacon at the rear of the trailer - Galvanized folding supports under the rear bevel of the loading platform - One mudguard at the rear of the trailer - Operating manual and documentation on USB stick - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and removable pump protection cover - Removable ALU side boards and tailgate on the gooseneck approx. 2,440 x 400 mm - The rear galvanized stanchions are removable (body length approx. 2,560 mm) - 3 pairs of WADER container pockets in the loading platform for 1x 20ft, 1x 30ft or 1x 40ft container - 6 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform - One INOX toolbox 1,500 x 390 x 810 mm under the loading platform, right side in direction of travel - Four warning signs, extendable by approx. 400 mm, approx. 423 x 423 mm with a position light - On the warning signs a bracket for a rotating beacon - Radio remote control for rear axle steering, in addition to cable remote control, with indicator lights on receiver for single-track monitoring - On the checker plate surfaces on the gooseneck and loading platform, a painted sand layer as anti-slip protection - Speed sticker 80 km/h at the rear and on both sides - Axle load gauge for determining axle loads, including load diagram

Stanje: rabljeno, lastna masa: 10.900 kg, največja dovoljena obremenitev: 43.600 kg, skupna masa: 54.500 kg, konfiguracija osi: 3 osi, prva registracija: 04/2025, dolžina tovornega prostora: 8.700 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 855 mm, velikost pnevmatike: 245/70 r17.5, barva: siv, Leto izdelave: 2025, obratovalna teža: 10.900 kg, Oprema: ABS, Gooseneck, rigid, center tube design: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Steel floor with anti-slip coating - Including perforated rail for aluminum approach ramps - 2" king pin - Manually operated BPW landing legs - 550 mm long, 8° chamfer at end of gooseneck - Front wall including park position for rear wall, 400 mm high - Spare wheel holder mounted vertically on the front side of the gooseneck - 3 pairs of recessed lashing rings (LC 5,000 daN) in the loading area of the gooseneck Hnsdpfx Aoi Ai E Rokbor - Aluminum side boards, 400 mm high, comprising 2x side boards each 3,150 mm long, and rear board with stanchions (galvanized) - Rectangular aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, center - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, left - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, right Loading platform, single-extendable: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Fixed section at front 700 mm - Steel plate floor with anti-slip coating - Chamfered transition between fixed part and deck for bridging rails and wheel recesses - Excavator trough including elongated holes for load securing (LC 1,500 daN), length approx. 3,850 mm - Prepared for hydraulic ramps (electrical supply) - Rails to widen up to 3,000 mm - 8° chamfered vehicle rear, 550 mm long - Slide system for easy mounting/dismounting of ramps - Continuous mud flap at the rear - 1 pair of lashing points LC 10,000 daN centrally on the loading area behind the gooseneck - 7 pairs of lashing points LC 10,000 daN in the outer frame of the loading platform - 6 pairs of stanchion pockets 100 x 50 mm in the outer frame of the loading platform - 1 pair of lashing points LC 10,000 daN centrally in the rear section of the loading platform - 1 pair of stanchion pocket rails approx. center of the loading area - 1 pair of stanchion pocket rails on the fixed part - 1 pair of stanchion pocket rails behind the last axle Ramps: - Hydraulic double-folding ramps, 2,750+1,500x800 mm - Larch wood surface - Operated by remote control (wired and wireless) - Quick-change ramp (dismantling system) Chassis: - Axle brand: BPW ECO Max - 2 ride heights - 4 axles @ 10 t (technically 12 t) - Twin tires 245/70 R17.5 - 2 x rigid axles and 2 x friction-steered axles - Reverse steering lock for friction-steered axles via reverse gear - Brake system by Knorr (according to EU standards with EBS-E) - Knorr TIM G2 (Trailer Information Module) - RSS (Roll Stability Support) stability control - Load-dependent lift axle on the first axle incl. starting aid (forced lowering of lift axle via TIM possible) Accessories: - 4 wheel chocks with holder - 2 pairs of warning panels 423 mm x 423 mm, with 2 position lights and socket for rotating beacon, steplessly adjustable up to 3,950 mm - Securing points on gooseneck and on loading platform (alternatively on ramp, if available) included - Plug-in bulkhead at the end of the excavator trough - Electrohydraulic unit for ramp operation - Ramp control by wireless remote - Hydraulic rear support legs for stabilization during loading - 1 pair of additional reversing lights at the rear, activated when reversing - Larch wood widening planks (option)

Stanje: rabljeno, lastna masa: 14.995 kg, največja dovoljena obremenitev: 50.805 kg, skupna masa: 65.800 kg, konfiguracija osi: 3 osi, prva registracija: 10/2023, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, barva: siv, Leto izdelave: 2023, obratovalna teža: 14.995 kg, Oprema: ABS, For every used semi-trailer, you will receive a current and comprehensive inspection and functionality report. Gooseneck: - Gooseneck with rear bevel, approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading platform: - Extendable loading platform with rear bevel, approx. 500 mm x 8° - 6 pairs of fold-out lashing rings to the outside (LC 5,000 daN) - 4 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) - 1 intermediate section, 250 mm - Cut-outs in the outer frame of the loading area for inserting tensioning straps (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, chequer plate over the axles Hnodpfov Hr Axjx Akbor Axles and tyres: - BPW axles with hydro-mechanical forced steering - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - Axle tools - Tyres 235/75 R17.5 Braking system: - Braking system according to EU regulations with EBS-E (4S3M) Accessories included: - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings mounted on the galvanized connection strip at the front - 4 chocks with holders on the front wall - One spare wheel with holder in front of the front wall - Electro-hydraulic power unit - Remote steering from front and rear via cable remote control with push buttons, including single-track control of the axles - Mounting for ALU ramps at the rear of the gooseneck - Hot-dip galvanized, extendable side extensions, approx. 230 mm per side - European reflector boards (red-yellow) at the rear of the trailer - White reflective tape as per EU standards on the sides, on the extension, and red at the rear - Bracket for warning signs on left/right of gooseneck and rear panel, incl. socket - Galvanized folding supports under the loading platform’s rear bevel - Holder for a beacon at the rear of the trailer - Central lubrication system with 2 BEKAMAX (Pico) pumps, NLGI-2 standard grease and removable cover for the pump - Mud flap at the rear of the trailer - Manual and documentation - On the gooseneck: insertable ALU side boards and rear wall, approx. 2,440 x 400 mm - Removable galvanized stanchions at the rear (body length approx. 2,560 mm) - 4 pairs of WADER container locks recessed in the loading platform for 1x 20ft, 2x 20ft, 1x 40ft, or 1x 45ft container - 8 pairs of pockets for removable stanchions, 100 x 50 mm, in the outer frame of the loading platform - Adjustable hook rails for ALU ramps at the rear of the vehicle - Lift axle on the front axle, controlled by TEBS E depending on current axle load and loading condition - Four warning panels, extendable approx. 400 mm, approx. 423 x 423 mm, each with position lamp - Mounting on warning panels for beacon - Radio remote control for remote steering in addition to cable remote control, with indicator lights on the receiver for single-track control - Painted-in sand layer on chequer plates, above the king pin and on the loading area for anti-slip protection - 80 km/h speed limit decal at the rear - Load pressure gauge for axle load determination, including load chart

Stanje: novo, lastna masa: 11.300 kg, največja dovoljena obremenitev: 36.700 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.250 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 r 22,5, barva: sivo-črna, Oprema: ABS, Loading platform: Loading platform in extendable design with pneumatically operated locking mechanism A fixed intermediate table, approx. 250 mm wide, is mounted on the central beam 8 pairs of lashing rings, foldable outwards (LC 5,000 daN) 3 pairs of lashing rings, foldable outwards (LC 10,000 daN) Openings in the outer frame of the loading platform for attaching tensioning straps (LC 2,000 daN) Axles and tyres: BPW axles and suspension, all axles with hydro-mechanical forced steering Disc brakes, technical axle load: 10,000 kg Air suspension with lift and lower valve Axle tools 6 tyres, size 385/65 R 22.5 Brake system: Brake system according to EU regulations with EBS-E (2S2M) Landing gear: JOST landing legs (mechanically operated) with 2-speed gearbox for 24 t lift load (50 t test load) Steel construction: Steel construction made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical system: Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX mounted on the front terminal board with 24N, 24S & 15-pin sockets Connections according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: First-class, long-lasting corrosion protection of the standard grit-blasted welded frame, guaranteed by a 2-component (2K) zinc-dust primer High-quality, single-colour 2-component (2K) top coat in Novagrau Rear section metallised and painted in RAL 9010 (pure white) No metallic paint finish possible Included accessories: At the gooseneck and at the rear plate, left and right, each with a bracket for warning signs, including socket Remote steering from the front and rear via cable remote control with push buttons, with single-track control of the axles Electro-hydraulic unit 4 wheel chocks with brackets on the front wall 2" kingpin A galvanised steel front wall approx. 2,200 mm high Yellow-red air couplings on the galvanised front terminal board White reflective tape on the side, at the extension and rear in accordance with EU regulations, red at the rear European reflective plates (red-yellow) on the rear of the trailer One mud flap on the rear of the trailer Manual and documentation Bracket for a revolving warning light at the rear of the trailer Loading platform with approx. 30 mm thick wooden floor set in omega profiles 10 pairs of stake pockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading platform 1 spare wheel holder under the loading platform on the right-hand side in the driving direction Hnedpfx Ashlz Shokbor 6 pairs of WADER container locks in the loading platform, for 1x 20ft container, 2x 20ft containers or 1x 40ft container; in the extension, an additional locking position is provided for a 45ft container 5 pairs of stake pocket strips, mounted transversely in the loading platform, for plug-in stanchions 100 x 50 mm A galvanised bracket mounted transversely under the loading platform (2,390 x 720 x 400 mm) Access ladder mounted on the right in the direction of travel One HDPE toolbox 1,200x500x480 mounted at the front under the loading platform on the left in the direction of travel Lift axle on the front axle with control via TEBS E depending on the current axle load and loading status Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable protection around the pump Red/white reflective tape on the extension of the loading platform On the central beam,

Stanje: rabljeno, skupna masa: 70.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/1998, Oprema: ABS, Vehicle identification number: XL952N5SAWL007036 Fifth wheel load: 20,000 kg - Axle loads: 5 x 10,000 kg Unladen weight: 13,100 kg Roadworthiness test (HU) due Neck length: 4,100 mm Coupling height: 1,250 mm Low-bed: Length: 9,200 mm (650 mm thereof chamfered) -- Width: 2,525 mm -- Loading height: 880 mm Extendable by 6,200 mm Widenable to 3,000 mm Hnodpfxeyx N Dvo Akber Detachable rails Axle load (technical): 5 x 10,000 kg SAF axles with drum brakes Axles 1, 2: liftable Axles 5, 6: friction-steered Tyres: 235/75 R 17.5 ===== Subject to changes, prior sale and errors. The description is for general identification of the vehicle and does not constitute a warranty in the legal sense. The purchase contract description is binding. Our offer is generally without new roadworthiness inspection (TÜV approval). If a new TÜV approval is required, we will gladly provide you with an offer from our partner workshops! Vehicle may be stickered and/or lettered with advertisements. Our general terms and conditions of delivery and payment apply.

Stanje: rabljeno, lastna masa: 10.650 kg, največja dovoljena obremenitev: 40.310 kg, skupna masa: 50.960 kg, konfiguracija osi: 3 osi, prva registracija: 04/2025, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 760 mm, skupna dolžina: 13.100 mm, skupna širina: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5, barva: siv, Leto izdelave: 2025, Oprema: ABS, Za vsak rabljen priklopnik prejmete aktualno in celovito poročilo o pregledu in funkcionalnosti. Gosi vrat: -Gosi vrat s trdo leseno oblogo debeline 30 mm -Gosi vrat zadaj v ravni izvedbi -3 pari pritrdilnih obročev (nosilnost 5.000 daN) Nosilna površina v izvlečni izvedbi: -Nosilna površina v izvlečni izvedbi -5 parov pritrdilnih obročev, ki se zložijo navzven (nosilnost 5.000 daN) -3 pari pritrdilnih obročev, ki se zložijo navzven (nosilnost 10.000 daN) -1 par pritrdilnih obročev, nameščenih v ležečem položaju na sprednji strani nosilne površine (nosilnost 10.000 daN) -Izrezi na zunanjem okvirju nosilne površine za obešanje zateznih trakov (nosilnost 2.000 daN) -Trda lesena obloga debeline približno 48 mm, nad osmi je obloga iz valjane pločevine Osi in pnevmatike: -Osi BPW, dve osi fiksni, dve osi s krmiljenjem -Zračna vzmetenje, s bobnastimi zavorami, z funkcijo dvigovanja/spuščanja -Krmiljene osi z elektromagnetsko blokado za vzvratno vožnjo, ki se aktivira s prestavo za vzvratno vožnjo ali ročno Hnedpfexwnfmox Akbjr -Orodje za osi -Pnevmatike 205/65 R17.5 -Sistem za nadzor tlaka v pnevmatikah TPMS, v skladu s standardom ECE R 141 Dodatna oprema vključena: -En rezervni kolesni komplet z nosilcem pred čelno steno -2" kraljevska vlečna glava -Pocinkana jeklena čelna stena, približno 400 mm visoka -Na pocinkani priključni letev spredaj, rumeno-rdeče zračne spojke -4 kosi zavor, z nosilcem na čelni steni -Pocinkane zložljive opore pod poševnino nosilne površine -Nosilec za rotacijsko luč na zadnji strani priklopnika -Razširitve, pocinkane, izvlečne za približno 230 mm na stran -Bel odsevni trak v skladu z direktivami EU, nameščen na boku, na izvlečnem delu in zadaj rdeče barve -Na gosi vratu in na zadnji plošči, na levi in desni strani, nosilci za opozorilne table, vključno z vtičnico -Lovilec umazanije na zadnji strani priklopnika -Evropske odsevne table (rdeče-rumene) na zadnji strani priklopnika -Na gosi vratu in na zadnji steni, ALU stranske plošče in zadnja plošča, ki se vstavi, približno 2.440 x 400 mm -Zadnji, pocinkani stranski nosilci so snemljivi. Dolžina nadgradnje približno 2.560 mm -7 parov WADER posod za zabojnike: -1 x 20-stopični zabojnik na nosilni površini -1 x 40-stopični zabojnik na nosilni površini -1 x 40-stopični zabojnik nad gosi vratom -2 x 20-stopični zabojniki -Podporni blok z 1 parom WADER posod za zabojnike (največja nosilnost približno 20.000 kg) -7 parov posod za stranske nosilce za vstavne nosilce 100 x 50 mm v zunanjem okvirju nosilne površine -Dvignjena os na sprednji osi, upravljanje preko TEBS E, odvisno od trenutne obremenitve osi in trenutnega stanja obremenitve -Pomikalna vstavna letev za ALU rampe na zadnji strani vozila -Na valjani pločevini na gosi vratu in na nosilni površini, nanos plasti peska za preprečevanje zdrsavanja -Štiri izvlečne opozorilne table, približno 400 mm, približno 423 x 423 mm, z pozicijsko lučjo -Na opozorilnih tablah nosilec za rotacijsko luč -Nalepka za omejitev hitrosti 80 km/h zadaj in na obeh straneh -Merilnik obremenitve za ugotavljanje obremenitve osi, vključno s tabelo obremenitve

Stanje: novo, največja dovoljena obremenitev: 42.900 kg, skupna masa: 55.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 29.000 mm, skupna širina: 2.540 mm, Oprema: ABS, The complete inventory of vehicles, including those available for immediate and short-term delivery, can be found on our website. Extract from the equipment list. Full specifications available upon request. Hsdpfx Akoyvnd Nobsnr Loading Platform: * Gooseneck, length approx. 3,900 mm with central beam * Loading platform, double extendable, length approx. 9,300 mm * A support plate, approx. 200 mm wide, is permanently welded to the central beam * Pneumatic locking system with conical locking pin and reinforced locking positions; supply lines are protected within the extendable beams and automatically adjust to the current platform length (except for the supply of the first and second locking positions) * Technical fifth wheel load: 25,000 kg Suitable for tractor units: 4 x 2, 6 x 2, and 6 x 4 * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, all axles hydro-mechanically forced steered, mounted on turntables * Technical axle load: 12,000 kg each, air suspension with lift and lower valve * 275/70 R 22.5 3PMSF twin tires. Brand at our discretion * ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for operating hydraulic functions * 3 pairs of recessed lashing rings in the outer frame of the gooseneck, foldable to the outside * 1 pair of lashing rings at the king pin (LC 10,000 daN) – all other lashing rings (LC 5,000 daN) * 3 pairs of stake pockets recessed in the outer frame of the gooseneck for plug-in stakes approx. 100 x 50 mm * 1 stake pocket bar mounted transversely on the gooseneck floor for plug-in stakes approx. 100 x 50 mm * 1x at the rear of the gooseneck * 2" king pin * Mechanical landing gear with 2-speed gearbox and crank * 8 pairs of stake pockets recessed in the outer frame of the loading platform for plug-in stakes approx. 100 x 50 mm * 10 pairs of recessed lashing rings in the outer frame of the loading platform, foldable to the outside * Remote steering from the front and rear via cable remote control, with axle tracking control, no installation required in the tractor unit * Last axle with air bellows venting activated when parking brake is applied * Steel front wall, approx. 1,600 mm high, certified design according to EN12642:2016 XL * Round NATO socket at the front connection bar (Maeler & Kaege VG 96 917) * 1 LED work light on each side at the landing gear, wired to the tractor unit connection bar * Approx. 32 mm wooden floor on the gooseneck and the loading platform * On the large-section extension tube, one locking position every approx. 500 mm * On the small-section extension tube, one locking position every approx. 1,000 mm, enabling locking at every approx. 500 mm * Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,500 daN) * 4 stake pocket bars mounted transversely on the loading platform floor for plug-in stakes approx. 100 x 50 mm * 4 wheel chocks with holder mounted under the loading platform * 1 lockable INOX toolbox, approx. 2,390 x 800 x 500 mm (L x W x H), mounted under the loading platform on the left in the direction of travel * 1 additional lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the loading platform on the right in the direction of travel * 1 LED work light each left and right in front of the axles, with wiring * 2 axle load gauges mounted on the left side including axle load diagram * 1st axle equipped with automatic lift axle function as well

Stanje: novo, največja dovoljena obremenitev: 96.500 kg, skupna masa: 126.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 26.900 mm, skupna širina: 2.750 mm, Oprema: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: * Hydraulically lift/lowerable and detachable gooseneck, approx. 3,650 mm long * For tractor units: 6x4 or 8x4 * Truck hydraulic connection with flow control (20 l/min), incl. gantry for supply line suspension; the tractor unit tank must have at least 80 l capacity * With MAX Trailer coupling units; otherwise, coupling units to be provided ex works by the customer * Gantry with winch for spare wheel mounted at the front of the gooseneck * 3.5-inch king pin * Steel front wall approx. 400 mm high * Removable aluminium side and rear boards on the gooseneck, approx. 400 mm high, anodised finish * Control lever on the gooseneck protected by a folding cover * Operator area lighting at gooseneck, with on/off switch * One 7-pin socket each at the left and right rear of the gooseneck for warning sign * BEKA-MAX central lubrication system for one gooseneck with standard NLGI-2 grease * Hydraulic connections from the gooseneck to the low-bed via screw couplings * Access steps on the gooseneck * Four warning panels extendable by approx. 1,000 mm (approx. 423 x 423 mm) each, with one LED position lamp and bracket for beacon * Mounting adapters for 2 spare wheels * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery. Output: 9.5 kW (12.9 hp) at 3,000 rpm * Hydraulic connecting lines between powerpack and connector plate at the gooseneck * One LED worklight left and right on the rear plate of the gooseneck, individually switchable * Radio remote control for: - Operating the powerpack, start/stop of diesel engine. - Operating remote steering (in addition to cable remote), with 2 LED indicator lights on receiver for single-track control. - Lift/lower gooseneck. - Lift/lower suspension of running gear 2-axle front module: * Bolt-eye coupling front and rear. Length: approx. 2,970 mm. Module width: approx. 2,750 mm * BEKA-MAX central lubrication system for 2-axle module with standard NLGI-2 grease (not connected to steering rods) * One 7-pin socket each at the left and right rear of the front module for warning signs * Platform surface with sand coating as slip protection * Yellow reflective tape in accordance with EU regulations at the sides, on the extension, and at the rear of the trailer * One 7-pin socket for warning signs, left and right on the front module, in the axle area * Extendable outriggers approx. 230 mm per side for the 2-axle module * 1 pair M42 threaded blocks between the axles of the front module Hodszahp Sjpfx Akbsnr * 1 pair brackets for plug-in warning panels in the stake pockets of the exterior frame of the loading area Loading platform: * 6-axle, double telescopic loading platform with bolt-eye coupling at the front and rear chamfer approx. 500 mm x 8° * Platform length: approx. 11,000 mm * Technically extendable by: approx. 8,200 + 7,700 mm * Axle spacing: approx. 1,500 mm * Base width: approx. 2,750 mm * Hydraulic coupling pin * BEKA-MAX central lubrication system for the platform with standard NLGI-2 grease * Platform surface with sand coating as slip protection * 11 pairs of recessed lashing rings in the external frame of the loading platform, foldable outwards (LC 10,000 daN) * Permanently welded intermediate table, approx. 500 mm long * 1 pa...