Faymonville 3-Achs-Tiefbett 3X10 T Außenträger nakup rabljenega (64.461)

Stanje: novo, največja dovoljena obremenitev: 36.040 kg, skupna masa: 53.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete inventory of immediately and short-term available vehicles can be found on our website. Excerpt from the equipment list. Full specification available on request. Gooseneck: * Gooseneck in SNT design to optimize loading deck length, approx. 3,750 mm long * Gooseneck hydraulically liftable/lowerable and detachable * For tractor units: 6 x 4 or 8 x 4 Lowbed: * Lowbed with exterior beams, extendable, SUPER LOW design, approx. 8,000 mm long * Lowbed with fixed hardwood flooring approx. 40 mm thick and mechanical locking * Supply lines routed protected within the extendable beams, automatically adapting to the lowbed length * 7 pairs of folding lashing rings outward (LC 10,000 daN) Podpfx Ajy Uwu Iem Togl * 6 pairs of threaded mounting blocks on the inner beam for screwable RUD rings Rear chassis: * Rear chassis with closed outer frame and tread plate cover * Chassis with excavator recess, closed in the rear half to house air tanks * 3 pairs of folding lashing rings outward (LC 5,000 daN) * 1 pair of folding lashing rings outward (LC 10,000 daN) * 1 pair of horizontal lashing rings, positioned front & rear on the chassis (LC 10,000 daN) Axles: * BPW axles and suspension, all axles with hydro-mechanical forced steering * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tyres: * Tyres 245/70 R 17.5 3PMSF – manufacturer at choice. Load index (146/146F) Braking system: * WABCO braking system according to EU regulations with EBS-E (2S2M) Coating: * HRM metalizing of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure optimal corrosion protection * Finished with 2 coats of 2K paint, single-colored in RAL 3002 Carmine Red, per RAL System 841GL Includes accessories: * 2-inch kingpin * One galvanized steel front bulkhead, approx. 400 mm high * At the galvanized front connection strip, yellow-red air couplings * Remote axle steering, from front and rear, operated by cable remote control with push buttons, including axle alignment monitoring (without installation on the tractor unit) * Preparation for bolt-on container lockings to accommodate 1 x 20', 1 x 40', or 1 x 45' container on the outer rails. Without container locks * Hydraulic connections from gooseneck to lowbed with a multicoupling instead of screw couplings * Electrohydraulic unit * Spiral cable (approx. 35 mm², approx. 3.5 m in length, max. 250A) for the power supply to the electrohydraulic unit and/or the electric winch, with plug connection (NATO-NATO) between trailer and tractor unit * Yellow reflective tape according to EU regulations, on the sides, extension, and at the rear of the trailer * At the gooseneck front and rear left and right, each with a holder for warning signs, including socket * Manual and documentation on USB stick * Central lubrication system with 2 pumps BEKAMAX (Pico) with standard grease NLGI-2 and removable protection for the pumps * 7 pairs of threaded blocks between the lashing rings under the top flange on the outer rail for mounting screwable RUD rings VLBG-4 * 2nd ride height, approx. 50 mm above standard ride position, selectable via manual control * On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm (L x H). The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) * Separate air connection with air gun on the gooseneck * A stainless steel toolbox, INOX, approx. 1,350 x 400 x 400 mm

Stanje: novo, lastna masa: 34.500 kg, največja dovoljena obremenitev: 106.700 kg, skupna masa: 141.200 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.150 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 580 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, obratovalna teža: 34.500 kg, Oprema: ABS, Gooseneck: - Gooseneck hydraulically lift/lowerable as well as detachable - Length approx. 3,650 mm - Extensive lashing positions - For tractor units: 6 x 4 or 8 x 4 3-Axle Compact Front Bogie: - Hook mounts at front and rear - Chassis length x chassis width approx. 3,560 mm x 2,850 mm - Extensive lashing positions Podpfx Amjwhywfe Tsgl Excavator Deck “BB-A”: - Telescopic excavator deck “BB-A” with drive-over deck hooks at the front and bolted lug coupling at the rear - Length x base width approx. 7,150 mm x 2,850 mm - Beam height x beam width approx. 430 mm x 1,350 mm - Loading height 580 mm with 150 mm ground clearance - 5 pairs of hanging lashing rings (LC 10,600 daN) - 4 pairs of threaded blocks M30 on inner beam for mounting screw-on rings 5-Axle Rear Bogie: - Mechanical bolt-on lug coupling for fitting a lowbed front, rear end traverse - Chassis length x chassis width approx. 6,840 mm x 2,850 mm - Extensive lashing positions Pendulum Axle and Tyres (front and rear bogie): - “PENDEL-AXLE”, all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-plugs for securing in lifted position - Final paint of axles with 2 coats of 2K paint, single-colour in MB 7350 Novagrau - Technical axle load: 14,640 kg (62 km/h) - Hydraulic axle compensation - Axle tools - Tyres 285/70 R19.5 Steering Override: - Remote steering from the front and rear via cable remote control with push buttons, including axle tracking control - Socket for steering control operation on the gooseneck - Cable remote control with push buttons including axle tracking control Included accessories: - Yellow-red air couplings on galvanised front connection rail - Steel headboard approx. 400 mm high - 4 wheel chocks with holders - 2 spare wheels 285/70 R19.5 - 3.5" kingpin - Gantry with winch for spare wheel at the front side of the gooseneck - Truck hydraulic connection with flow control valve (40 l/min), including gantry for suspension of supply lines, tractor unit tank must be at least 80 litres with couplings - White reflective tape according to EU regulations on sides and extension, red at rear - Plug-in ALU side panels and rear wall on gooseneck, approx. 400 mm high, anodised - Operating lever on gooseneck protected by folding cover - Separate air connection with air pistol on gooseneck - Central lubrication system BEKAMAX with standard grease NLGI-2: 1x on the gooseneck, 1x on 3-axle bogie, 1x on 5-axle bogie - Variomax tool kit - Multi-coupling hydraulic connections in the lowbed hook area - Front bogie with separate air connection for air screwdriver - Threaded inserts (ø 40 mm) every approx. 500 mm on outside of upper flange of excavator deck for screw rings - Folding extensions with steel mats, width adjustable from approx. 2,850 mm to approx. 3,250 mm - Steel mats with rubber covering approx. 12 mm thick - Two INOX toolboxes 855 x 340 x 390 mm - Radio remote control for steering override in addition to cable remote - Painted sand layer as anti-slip measure - 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery

Stanje: novo, lastna masa: 17.250 kg, največja dovoljena obremenitev: 48.700 kg, skupna masa: 66.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 375 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 17.250 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize loading platform length, approximately 3,750 mm long - Gooseneck hydraulically liftable, lowerable, and detachable - For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Lowbed: - Lowbed with external beams, designed as a telescopic vessel bridge in low-profile construction with front extension - Length x width approx. 7,550 mm x 2,740 mm Psdpfeh Hm Tzex Am Togl - Mechanical locking of the extension Chassis: - Rear chassis with closed outer frame - Checker plate surface and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, Suspension, and Tyres: - “PENDEL-AXLE”, all axles hydromechanically forced steered - Burst protection valve on the axle compensation cylinders with automatic reset function - Hydraulic cylinders with shut-off valves and plug pins for securing in raised position - Final coating of axles: two coats of single-color 2-component paint in "FAY-Grey-34-0260" - Technical axle load 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 Accessories: - Detachable steel front wall, approx. 400 mm high - 4 wheel chocks - Rear upper gooseneck area closed with removable cover - 1 pair of steel ramps with climbing bars and locking bolts to bridge the lowbed mounting hooks - Ramps can be positioned over or between the hooks - Mounting options for steel drive-on ramps at the rear, between the outer beams of the gooseneck - Locking point approx. every 1,000 mm on the extension - 1 lashing ring each, left and right, on the front cross member - Supply line connection strip for tractor unit, mounted at the height of outer frame profile - 6 pairs of threaded blocks on the exterior of the load floor inner beams for attaching M24 screw rings - 6 pairs of recessed lashing rings on the outside of the load floor outer beams, foldable inwards and outwards - 1 pair of threaded blocks on the front and rear of the load floor outer beams for M24 screw rings - Mounting rail for loose aluminum approach ramps on the end cross member of the vehicle - Central lubrication system with 2 pumps, brand BEKAMAX - Remote steering front and rear, cable remote controlled, with axle tracking control - 3 kW electro-hydraulic power unit for hydraulic operations, except hydraulic winches - Removable galvanized loading floor, can be placed in 3 elements between the outer beams, with hardwood covering - Foldable extensions, approx. 230 mm per side - Loose extension boards, steel-edged - 4 warning signs approx. 423 x 423 mm - Radio remote control for rear steering - 3.5” kingpin - Anti-slip coating on the left chamfer of the gooseneck - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Guide plate from gooseneck for the fifth wheel plate, approx. 800 mm wide - 1 spare wheel with mounting adapter - Parking position on the gooseneck for warning signs when not in use - 2 pairs of stake pockets integrated into the chassis outer frame, for plug-in stakes approx. 100 x 50 mm - Excavator stick trough of rear chassis closed at the rear with a removable plate - Trailer color: Mercedes-Benz 7350 Novagrey

Stanje: novo, lastna masa: 17.500 kg, največja dovoljena obremenitev: 43.500 kg, skupna masa: 61.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.750 mm, višina nakladalnega prostora: 400 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - For tractor units: 6x4 or 8x4 Lowbed: - Lowbed with external beams, extendable version, "SUPER LOW" design, approx. 7,550 mm long - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking device - Service lines are protected within the extendable beams and automatically adjust to the lowbed length Rear Undercarriage: - Rear chassis with closed outer frame, checker plate cover, and continuous prism-shaped excavator trough approx. 1,450/900 x 505 mm, open at the rear - 2 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame Axles and Tires: - "PENDULUM AXLE", all axles hydro-mechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 / 3PMSF Included Accessories: - Prepared for bolt-on container positioning for 1x 20ft or 1x 40ft container on the outer beams - 2" kingpin - Galvanized steel front wall approx. 400 mm high - One spare wheel with holder - At the galvanized front adapter bar yellow-red air couplings - 4 wheel chocks - Remote rear steering from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Hydraulic line connections from gooseneck to lowbed with multi-coupling instead of screw coupling - Electro-hydraulic power pack - White reflective tape to EU specifications on sides, extension, and rear red - 2 wooden blocks 500x250x200 mm - European reflective plates (red-yellow) on the trailer rear - At the gooseneck and rear wall left and right each a bracket for warning boards including socket - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 - Load gauge for determination of axle loads including load diagram - On the gooseneck, plug-in ALU side and rear boards approx. 2,000 x 400 mm - The rear galvanized insert posts are removable (body length approx. 2,120 mm) - Separate air connection for air gun on the gooseneck Podpfx Amsh Hm Ths Togl - Duomatic air coupling from gooseneck to lowbed - Rear upper section of gooseneck closed with removable cover - 1 pair of steel ramps to bridge the lowbed's pick-up hooks - Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm - Wireless remote control for rear steering in addition to cable remote, with signal lights at receiver for single-track monitoring - 6 pairs of threaded blocks between lashing rings under the top chord on the outer beams for mounting screwable RUD rings VLBG-4 - 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading bed - Foldable extensions, approx. 230 mm per side - Loading area features a painted sand layer for anti-slip protection - Dipper stick trough of rear chassis closed at front and rear with plug-in plates - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - alu 15%)

Stanje: rabljeno, lastna masa: 10.350 kg, največja dovoljena obremenitev: 37.650 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 10/2018, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 245/70 R 17,5, barva: oranžna, Leto izdelave: 2018, obratovalna teža: 10.350 kg, Oprema: ABS,

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, lastna masa: 12.900 kg, skupna masa: 49.000 kg, konfiguracija osi: 2 osi, prva registracija: 03/2022, Leto izdelave: 2022, Faymonville 2-axle lowbed semi-trailer MEGAMAX 2x12 t PA 2 steered axles Single-extendable, 2 x 12 t pendle axles Overall length: approx. 13,500 mm Overall width: approx. 2,550 mm Neck width: approx. 2,480 mm Load bed width: approx. 2,550 mm Chassis width: approx. 2,550 mm Technically extendable: approx. 4,700 mm Coupling height (loaded): approx. 1,205 mm Loading height (max. loaded): approx. 1,005 mm Load area length: approx. 6,850 mm Chassis length: approx. 2,600 mm King pin distance to front: approx. 1,200 mm Swing radius of tractor unit (rear): approx. 2,300 mm Swing radius (front): approx. 1,800 mm Axle spacings: approx. 1,360 mm Gooseneck: - Gooseneck in SNT design for optimized load floor length, length approx. 3,750 mm - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth-wheel load: 25,000 kg Boiler deck: - Deep-designed extendable boiler deck "SUPER LOW" design - Length approx. 6,850 mm, with mechanical locking system Rear chassis: - Rear chassis with closed outer frame, chequer plate and continuous prism digger recess, approx. 1,250/700 x 505 mm, open at the rear - PENDLE-AXLE, all axles hydro-mechanically forced-steered - Burst hose valve on axle compensation cylinder with automated RESET function - Hydraulic cylinders with shut-off cocks and front pins to secure lifted position - Technical axle load: 12,000 kg each - Hydraulic axle levelling Brake system: - WABCO brake system, EBS-E according to regulations Chassis tyres: - 245/70 R 17.5 3PMS Metalizing: - Complete HRM metallization (High Resistance Metallisation) - Entire steel structure shot-blasted, then hot-finished with ZINACOR 850 (Zinc 85%, Alu 15%) Painting: - 6-coat final treatment - Entire steel structure shot-blasted after welding. One layer of zinc-based primer, one adhesion primer. Final coat with 2 layers of 2K lacquer (acrylic) in a single colour, followed by cavity sealing with special wax - Trailer colour: RAL 3002 Carmine Red - Rim colour: Silver Grey - Side board colour: Natural Aluminum Pgodsy Hxd Iopfx Am Tjl Steel structure: - Steel structure made of high-strength fine-grained steels. - Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690Q/S700MC (yield strength 690MPa) - MAG welding process according to EN ISO 4063

Stanje: novo, največja dovoljena obremenitev: 90.700 kg, skupna masa: 126.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.850 mm, Oprema: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: Hydraulically lift/lower and detachable gooseneck. Length approx. 3,650 mm. Suitable for tractor units: 6x4 or 8x4 3-axle compact front bogie: * Hook mounts at front and rear. Length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Lowbed: * ATX-A lowbed with telescopic longitudinal beams in low-profile design, fixed hardwood floor approx. 50 mm thick * With drive-over bridge hooks at the front and bolt-lug coupling at the rear * Base width: approx. 2,850 mm, length: approx. 7,150 mm, beam height: approx. 330 mm, beam width: approx. 750 mm * Loading height approx. 480 mm, ground clearance approx. 150 mm 5-axle rear bogie: * Mechanical bolt-lug coupling for attaching a lowbed at the front; rear end traverse * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * Pendulum axle 3-axle front bogie: * PENDULUM AXLES, all axles hydro-mechanically forced-steered * Hose rupture valve on axle leveling cylinder with automatic RESET function * Hydraulic cylinders with shutoff taps and locking pins for securing in raised position * Final painting of axles with 2 coats of single color 2K paint, painted in MB7350 Novagrau * Rated axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tires for front bogie: 12 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J 5-axle rear bogie: * PENDULUM AXLES, all axles hydro-mechanically forced-steered * Hose rupture valve on axle leveling cylinder with automatic RESET function * Hydraulic cylinders with shutoff taps and locking pins for securing in raised position * Final painting of axles with 2 coats of single color 2K paint, painted in MB7350 Novagrau * Rated axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tires for rear bogie: 20 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimum corrosion protection * Final painting with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, according to RAL-System 841GL Including accessories: * Steel front wall, approx. 400 mm high * Plug-in aluminum side and rear boards on gooseneck, approx. 400 mm high, anodized * 3.5" kingpin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections on gooseneck * Front bogie with separate air connection for air impact wrench * BEKA-MAX central lubrication for one 3-axle bogie * Preparation for bolt-on container positioning for 1 x 20' or 1 x 30' on the outer beams * Without container locks * Brackets on the outer beams for installing foldable extensions * One 7-pin socket left and right, front and rear on rear bogie for warning panels * BEKA-MAX central lubrication for one 5-axle bogie * On the rear bogie, socket for cable remote control for steering Pgsdpfx Amow Tgp Do Tjl * Rear bogie with trough * 2 LED reversing lights mounted on rear panel * European reflector boards (red-yellow) on the rear * One mudflap at rear * One LED beacon with bracket left and right on rear cross-member * Two INOX toolboxes 855 x 340 x 390 mm on gooseneck, left and right * 1-circuit...

Stanje: rabljeno, lastna masa: 15.550 kg, največja dovoljena obremenitev: 47.450 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2024, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, Leto izdelave: 2024, Oprema: ABS, For every used semi-trailer, you will receive a current and comprehensive inspection and functional report. Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,700 mm long - Gooseneck rear with chamfer, approx. 1,000 mm x 10° Loading platform: - Extendable loading platform, approx. 8,800 mm long, with chamfer at the rear approx. 500 mm x 10° - A recess in the loading platform and into the chamfer to accommodate the excavator's dipper stick - Pneumatic locking with conical locking bolts and reinforced locking positions - Hardwood surface on the chamfer of the loading platform Ramps: - 1 pair of two-part steel ramps, approx. 4,350 mm long and 900 mm wide - Ramps with hardwood inlay - Hydraulically foldable ramp tips - Ramps can be hydraulically shifted approx. 235 mm outwards and 215 mm inwards individually - Square climbing strips 20 x 30 mm, spaced approx. every 200 mm on the outer frame of the ramp Pjdjypb Akspfx Am Togl Axles and Suspension: - BPW axles and suspension, 1st axle with forced steering, all other axles hydro-mechanically forced steered - Technical axle load: 12,000 kg - Air suspension - Tyres 235/75 R 17.5 - TPMS tyre monitoring system - TPMS tyre pressure sensors Included Accessories: - Plug-in steel front wall, approx. 400 mm high - 3kW electro-hydraulic unit for hydraulic operations - 1 spare wheel - Outer beams on the gooseneck with fixing holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings at the rear of the gooseneck - On the gooseneck: 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized - On the gooseneck: 1 plug-in ALU rear board, approx. 400 mm high, anodized - 2" kingpin - Round NATO socket at the front connection bar - 4 wheel chocks - Mechanical landing gear with 2-speed gearbox and crank - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front crossmember - 8 pairs of recessed lashing rings in the outer frame of the loading platform, foldable outwards - Extendable galvanized outriggers, approx. 230 mm per side - Wheel recesses with square climbing strips, 15 x 15 mm, open continuously in front of the axles up to the gooseneck crossmember, approx. 700 x 410 mm - ALU covers for the wheel recesses - Lockable aluminium elements fitted on the extension pipes of the outriggers - Widenable U-profiles for inserting the ALU covers - Wheel recesses with square climbing strips, 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - Lockable aluminium elements fitted on the extension pipes of the outriggers - 1 pair of mechanical rear supports - Remote steering control from both front and rear by cable remote control, with axle single-track alignment control - 1st axle with automatic lift axle function and start assist according to EU Directive 2021/535 - Under the gooseneck and at the rear crossmember left and right: 7-pin sockets with mountings for warning plates - Square climbing strips 20 x 30 mm, spaced approx. every 200 mm on the chamfered part of the loading platform outer frame - Central lubrication system with 1 pump, BEKAMAX - Radio remote control for steering in addition to cable remote - Wabco Smart Board system - 4 warning plates, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, lastna masa: 11.000 kg, največja dovoljena obremenitev: 38.500 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm hardwood flooring Load Area: - Extendable loading area with rear taper approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses fitted with square climbing strips 15 x 15 mm, including lower extensions - Between the 1st and 2nd axle, a pair of fixed wheel recesses with cover, approx. 1,610 x 970 x 400 mm - Recess in the bevel as well as protruding into the loading area for parking excavator dipper stick approx. 2,900 x 750 x 210/290 mm - 1 pair of lashing rings, installed flat at the front of the load area (LC 10,000 daN) - 5 pairs of folding lashing rings on the outside (LC 5,000 daN) - 2 pairs of folding lashing rings on the outside (LC 10,000 daN) - 2 pairs of lashing rings in the dipper stick recess (LC 5,000 daN) - Cut-outs in the outer frame of the load area for securing straps (LC 2,000 daN) - Incl. three-part removable galvanized covers over the wheel recesses – max. point load 3.5 t / pc. Two-piece Steel Ramps: - One pair of galvanized, two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood surfacing - Ramp with hydraulically folding ramp sections, hydraulic lifting gear, and hydraulically adjustable Axles and Tyres: - BPW axles and suspension, 2 rigid axles, 1 steering trailing axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lifting and lowering valve - Axle tool kit - Tyres 235/75 R 17.5 - TPMS tyre pressure monitoring system in accordance with ECE R 141 Accessories Included: - Mounts for warning signs left and right at the gooseneck and at the rear, each with socket - One spare wheel - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings at the galvanized front connector strip - 4 wheel chocks - Galvanized, extendable outriggers approx. 230 mm per side - Galvanized folding supports beneath the loading area bevel - Rear trailer bracket for rotating beacon - Cover plates for bridging the gap between ramps and load area - White reflective tape to EU regulations, sides and on extensions; rear in red - Electro-hydraulic unit installed at the rear beneath the loading area - Ramp control valves mounted on right trailer side - European reflective panels (red-yellow) on rear of trailer - Four extendable warning boards, approx. 423 x 423 mm, with position light Pgodpsup U Hzefx Am Tjl - Bracket for rotating beacon on warning boards - Removable ALU side boards and rear board on gooseneck approx. 2,440 x 400 mm - Rear galvanized removable stakes (structure length approx. 2,560 mm) - 2 pairs of WADER container pockets in loading area for 20ft or 30ft container - 3 pairs of socket pockets for stakes 100 x 50 mm in outer frame of loading area - Removable, galvanized intermediate table with 1 pair of WADER container pockets - Square climbing strips 20 x 20 mm spaced every 200 mm on outer frame at loading bevelling - Painted sand layer on chequer plates of the gooseneck and loading area for anti-slip protection - 80 km/h speed stickers rear and both sides - Load manometer for axle load measurement, including load chart.

Stanje: novo, lastna masa: 10.700 kg, največja dovoljena obremenitev: 38.800 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17,5, barva: sivo-črna, Oprema: ABS, Gooseneck: • Gooseneck with front corners beveled at 45° and rear taper approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Extendable loading platform: • Loading platform in extendable design with rear taper approx. 1,000 mm x 8° • Cut-outs in outer frame of loading platform for attaching tensioning straps • Approx. 48 mm thick hardwood flooring; anti-slip checker plate covering above the axles Two-piece steel ramps: • One pair of galvanized, two-piece steel ramps with approx. 48 mm thick hardwood covering • Ramps with hydraulically foldable ramp sections, hydraulic lift system, and hydraulically adjustable • Maximum load per pair: approx. 40,000 kg Axles and tires: • BPW axles and suspension, 2 rigid axles, 1 self-steering axle • Technical axle load: 12,000 kg • Electromagnetic reverse lock, activated via reverse gear or manually • Air suspension with lift and lower valve • Axle tools • 235/75 R 17.5 3PMSF Braking system: • WABCO braking system according to EU regulations with EBS-E Paintwork: • First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component zinc dust primer • High-quality, single-color top coat in MB 7350 Novagrey applied with two-component paint • Rear section metallized and painted in RAL 9010 Landing legs: • JOST landing legs with 2-speed gearbox for 24t lifting load (50t test load) Steel construction: • Steel construction made of high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC • S690QL/S700MC Electrical system: • Electrical system in accordance with EU regulations, 24 Volt lighting • ASPÖCK-UNIBOX on front connection panel with 24N, 24S & 15-pin sockets Accessories included: • One spare wheel with holder • Galvanized steel front wall approx. 400 mm high • Yellow-red air couplings on the galvanized front connection panel • 4 wheel chocks • Rear mounting bracket for beacon light at the end of the semitrailer • Recess at rear of gooseneck for ALU approach ramps • Galvanized folding supports under the loading platform taper • Cover plates to bridge the gap between ramps and loading platform • White reflector tape per EU regulations on sides, extension, and red at rear • Electro-hydraulic unit at rear, under the loading platform • On gooseneck and ramps, left and right, each with a holder for warning signs, including socket • Operating valves for the ramps located on the right side of the trailer Psdohlz S Nepfx Am Tsgl • ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) • Four warning panels extendable by approx. 400 mm with a position light • 3 pairs of WADER container pockets in the loading platform for one 20ft, 30ft or 40ft container • 6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading platform • Galvanized extensions, extendable by approx. 230 mm per side • 20 x 20 mm square climbing strips every 200 mm on the outer frame of the platform taper • Painted anti-slip sand layer on checker plates, above king pin and loading platform • Load gauge for axle load measurement, including load diagram • HRM metallization (High Resistance Metallisation) of the outer frame • Complete steel construction shot-blasted, then defined visible surfaces metallized and hot-finished with ZINACOR 850 (Zinc 85% - Alu 15%)

Stanje: novo, lastna masa: 15.550 kg, največja dovoljena obremenitev: 47.450 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimization of loading platform length, length approx. 3,700 mm - Rear gooseneck with bevel approx. 1,000 mm x 10° Loading Platform: - Extendable loading platform, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° - A recess in the loading platform as well as into the bevel for accommodating the excavator dipper stick - Pneumatic locking with conical locking bolts and reinforced lock positions - Hardwood covering on the loading platform bevel Ramps: - 1 pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm - Ramps with hardwood covering - Hydraulically folding ramp tips - Ramps can be hydraulically shifted individually approx. 235 mm outward and approx. 215 mm inward - Square climbing cleats 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, 1st axle lift-steered, all other axles forced-steered with hydromechanical system - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with raising and lowering valve - Tyres 235/75 R 17.5, twin tires - TPMS tire monitoring system compliant with ECE R141 - TPMS sensors installed in all wheels including spares Accessories included: - Removable steel front wall, approx. 400 mm high - 3kW electro-hydraulic power pack for hydraulic operations, excluding hydraulic winches - Parking position on gooseneck for warning boards when not in use - 1 spare wheel - On the gooseneck: 1 pair of removable side aluminium drop sides, approx. 400 mm high, anodised - On the gooseneck: 1 removable rear aluminium drop side, approx. 400 mm high, anodised - Above the gooseneck: approx. 40 mm thick hardwood floor, chequer plate above king pin Pgodpfx Ask Aht Usm Tel - 2" king pin - Guide plate on gooseneck for fifth wheel, approx. 500 mm wide - 4 wheel chocks - Mechanical landing gear with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - 1 intermediate table, approx. 300 mm wide - Extensions (galvanised) extendable by approx. 230 mm per side - Wheel recesses with square climbing cleats - ALU covers for the wheel recesses - 1 pair of mechanical rear supports - Remote steering at front and rear via cable remote control, with single track monitoring of axles - 1st axle with automatic lift axle function - Central lubrication system with 1 BEKAMAX brand pump - Radio remote control for remote steering, additionally to cable remote, with 2 indicator lights on the receiver as single track monitoring - Wabco Smart Board System - 4 warning boards, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for revolving beacon

Stanje: novo, lastna masa: 29.600 kg, največja dovoljena obremenitev: 72.400 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 6.650 mm, širina tovornega prostora: 2.840 mm, višina nakladalnega prostora: 550 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, obratovalna teža: 29.600 kg, Oprema: ABS, Gooseneck: - Gooseneck hydraulically liftable/lowerable and detachable - Length approx. 3,650 mm - For tractor units: 6 x 4 or 8 x 4 2-axle front bogie: - Hook mountings at front and rear - Bogie length x width approx. 2,200 mm x 2,850 mm Excavator deck "BB-A": - Telescopic excavator deck "BB-A" with drive-over bridge hooks at the front and pin-lug coupling at the rear - Length x base width approx. 6,650 mm x 2,850 mm - Beam height x beam width approx. 400 mm x 1,350 mm - Loading height 550 mm with 150 mm ground clearance 4-axle rear bogie: - Mechanical pin-lug coupling for the installation of a lowbed at the front, rear crossmember at the back - Bogie length x width approx. 5,480 mm x 2,850 mm - Multiple lashing points Pendulum axles and tyres (front and rear bogies): - "PENDULUM AXLE", all axles forced-steered via hydromechanics - Hose rupture valve on axle compensation cylinders with automatic RESET function - Hydraulic cylinders with shut-off valves and locking clips for securing in raised position - Final coating on axles: 2 layers of single-colour MB 7350 Novagrau 2K paint - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres size 285/70 R19.5 Remote steering (after-steering): - Remote steering operable from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Socket for remote steering control on gooseneck Podpfswcmhajx Am Tsgl - Cable remote control with pushbuttons and single-track control included Accessories included: - Yellow and red air couplings on the galvanised front connection bar - Steel front wall approx. 400 mm high - 4 wheel chocks - 3.5" king pin - One 7-pin socket left and right at rear of gooseneck for warning boards - Hoisting jib with winch for spare wheel at the front face of the gooseneck - Truck hydraulic connection with flow control (40 l/min), including support jib for supply lines; tractor unit tank must have at least 80 litres capacity with couplings - Plug-in ALU side and rear boards on gooseneck, approx. 400 mm high, anodised - Control lever on gooseneck protected by foldable cover - Separate air connection with air gun on gooseneck - BEKAMAX central lubrication system: 1x on gooseneck, 1x on 2-axle and 1x on 4-axle bogie - Variomax tool kit - Multi-coupling hydraulic connectors on gooseneck and at lowbed hook interface - 2 spare wheels - One 7-pin socket left and right, at front and rear of rear bogie for warning boards - Front bogie with separate air connection for impact wrench - Foldable steel bed extensions, adjustable in width from approx. 2,850 mm to 3,250 mm - Steel bed inserts can be placed in 2 positions for sunken load area - Steel mats with rubber flooring, approx. 12 mm thick - Thread-in options (⌀ 40 mm) every approx. 500 mm on the upper flange of the excavator deck outer tube for eye bolts - One locking point at every approx. 500 mm on extension with mechanical lock - Socket on rear bogie for remote steering cable control - 2 reversing lights on rear panel - Four extendable warning boards (by approx. 2,000 mm), each approx. 423 x 423 mm with position lights - 1 work light left + right on rear panel of gooseneck with separate on/off switches - Two INOX toolboxes, approx. 855 x 340 x 390 mm - 1-cylinder Hatz diesel engine (Silent Pack) - Radio remote control for after-steering

Stanje: novo, lastna masa: 10.900 kg, največja dovoljena obremenitev: 37.100 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 890 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, obratovalna teža: 10.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the loading platform length, approx. 3,700 mm long, rear bevel approx. 1,000 mm x 6° - Technical king pin load: 18,000 kg - For tractor units: 4 x 2 and 6 x 2 Loading platform: - Loading platform, approx. 9,600 mm long with rear taper approx. 900 mm x 6° - Platform area behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, with a load capacity of up to approx. 9,000 kg - Grating surface and steel sheet floor approx. 5 mm thick as additional reinforcement on the sloped section of the platform Ramps: - One pair of two-section AXS steel ramps, approx. 4,675 mm long and approx. 900 mm wide - Grating surface - Hydraulically folding ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 365 mm inward - Painted sand coating on the outer frame and ramp tips - Flashing lights on the outer sides of the ramp tips with control switch next to the ramp operation panel - Ramp lock in transport position with quick-release fastener Axles, suspension and tires: - BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steerable (trailing) - 1st axle with traction assistance - Operated via brake pedal in the tractor unit - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 - TPMS tire pressure sensors installed on all wheels including spare wheels Brake system: - WABCO EBS-E braking system in accordance with EU regulations Paintwork: - Trailer MB 7350 Novagrau Equipment included: - Removable front steel wall, approx. 400 mm high - 3 kW electro-hydraulic power unit for hydraulic operations, except for hydraulic winches - Gooseneck guide plate for the fifth wheel, approx. 500 mm wide - JOST Module B – static test load = 50,000 kg - Continuous grating with 5 mm steel underlay as additional reinforcement Pgedpfxeuadk Nj Am Tjl - Painted sand coating - Cutouts in the outer frame of loading platform and lift bed for hooking hydraulic ramp control valves on the right-hand side of the vehicle - 2" king pin - Central lubrication system with 1 pump, brand BEKAMAX - 1 pair of plug-in ALU side boards on the gooseneck, approx. 400 mm high, anodised - Electric winch, approx. 5,400 kg pulling force, with radio remote control - Steel wire rope approx. 24 m long, rope diameter approx. 9.5 mm, including rope pressure roller - WABCO Smart Board system - 4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, lastna masa: 10.350 kg, največja dovoljena obremenitev: 39.150 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Loading area: - Telescopic loading area with rear chamfer approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm - Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom - Between the 1st and 2nd axle, 1 pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm - 3-piece detachable galvanized covers over the wheel recesses (W 670 mm) – max. point load 5 t / pc. - Recess in the chamfer and protruding into the loading area for the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of foldable external lashing rings (LC 5,000 daN) - 2 pairs of foldable external lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) - Cutouts in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) Psdpfx Amsiu Er Ae Tegl One-piece aluminum ramps: - 1 pair one-piece ALU ramps, approx. 2,500 x 600 mm - Ramp with spring lifting mechanism and manually adjustable - Maximum load per pair: 24,000 kg Axles and tires: - BPW axles and suspension, 2 rigid axles, 1 trailing steering axle - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tyres 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 Accessories included: - 1 spare wheel with holder in front of the bulkhead - 2" kingpin - 1 galvanized steel front wall approx. 400 mm high - At the galvanized coupling rail at the front, yellow-red air couplings - 4 wheel chocks with holder at the bulkhead - Mounting point at the rear of the gooseneck for ALU ramps - Galvanized extensions, extendable by approx. 230 mm per side - Galvanized folding supports under the chamfer of the loading area - 1 holder for a rotating beacon at the rear of the trailer - White reflective tape laterally, at the extension, and red at the rear, per EU regulations - At the gooseneck and rear panel, left and right, each with a holder for warning signs including socket - On the gooseneck, plug-in ALU sideboards and rear wall, approx. 2,440 x 400 mm - The rear galvanized stakes are removable (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container - 3 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area - 1 removable galvanized intermediate table with 1 pair of WADER container pockets - 20 x 20 mm square climbing strips every 200 mm on the outer frame in the chamfer of the loading area - Anti-slip sand coating on the checker plates on the gooseneck and the loading area - Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with position light - Holder for rotating beacon on the warning signs - 80 km/h speed stickers at the rear and on both sides - Load gauge for determining axle loads including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then all defined visible surfaces metalized and hot-finished with ZINACOR 850 (Zinc 85% – Alu 15%)

Stanje: novo, lastna masa: 12.900 kg, največja dovoljena obremenitev: 34.100 kg, skupna masa: 47.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 350 mm, vzmetenje: drugo, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 12.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm in length - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2, and 6x4 Loading Platform: - Low-bed with external beams, extendable “SUPER LOW” design, approx. 6,850 mm in length - Low-bed with fixed hardwood flooring, approx. 40 mm thick, with mechanical locking device Rear Chassis: - Rear chassis with closed outer frame, chequer plate covering, and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings, foldable to the outside - 1 pair of lashing rings recessed in the trough - 2 pairs of stake pockets for insertable stakes 100 x 50 mm in the external frame Pendulum Axle and Tyres: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and safety locking pins for securing in raised position - Axles painted with two layers of single-colour 2K paint in “FAY-Grey-34-0260” - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 - TPMS tyre pressure monitoring system according to ECE R 141 Accessories: - Preparation for the installation of bolt-on container locators for 1 x 20ft or 1 x 40ft container on the outer girders - 2" king pin - One galvanized steel front wall, approx. 400 mm high - One spare wheel - Yellow-red air couplers on the galvanized front connection bar - 4 wheel chocks - Remote steering from front and rear, operable via wired remote control with push buttons, with single-track alignment control Pgedpfxjhlz R Se Am Tjl - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of screw couplings - Electro-hydraulic power unit - White reflective tape in accordance with EU regulations on sides, extension, and rear - European reflective plates (red-yellow) on the rear of the trailer - One bracket on each side of gooseneck and rear plate for warning panels, including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on outer beam for mounting screw-on RUD Rings VLBG-4 - Detachable ALU side boards and rear board on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized insertable stakes are removable (body length approx. 2,560 mm) - Gooseneck rear upper area covered with removable cover - 5 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading area - Folding extensions, approx. 230 mm per side - 2 pairs of bolted RUD Rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the mounting hooks of the low-bed - Anti-skid sand layer painted on loading surface - 80 km/h speed stickers at rear and both sides - Spoon boom trough at rear chassis closed at rear with plug-in plate - Four extendable warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for rear axle steering in addition to cable remote, with indicator lights on receiver for alignment control - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard NLGI-2 grease - Load pressure gauge for determining axle loads - HRM Metallisation (High Resistance Metallisation) of outer frame - Complete steel structure shot blasted, then all defined visible areas metallized and finished with ZINACOR 850 (zinc 85% - aluminium 15%) hot galvanizing

Stanje: novo, lastna masa: 9.500 kg, največja dovoljena obremenitev: 35.500 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.500 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 435/50 R 19.5, barva: siv, obratovalna teža: 9.500 kg, Oprema: ABS, Loading platform in extendable design: Loading platform with hardwood planks, rear bevel approx. 1,000 mm x 8° 1 pair of fixed integrated wheel recesses, approx. 1,610 x 970 x 400 mm 2 pairs of lashing rings (LC 5,000 daN) 1 pair of lashing rings (LC 10,000 daN) 6 pairs of fold-out lashing rings on the outside (LC 5,000 daN) 2 pairs of fold-out lashing rings on the outside (LC 10,000 daN) Cut-outs in the outer frame of the loading area for attaching tensioning straps (LC 2,000 daN) Brake system: Brake system as per EU regulations with EBS-E (2S2M) Paintwork: Premium, long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc-rich primer High-quality single-colour 2-component (2K) top coat in Nova grey Rear section metallized and painted in RAL 9010 (Pure White) No metallic paint possible Landing gear: JOST mechanical landing gear with 2-speed gearbox for 24t lifting capacity (50t test load) Steel construction: Pgsdpok Eammsfx Am Tjl Steel construction from high-tensile fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical system: Electrical system according to EU regulations, 24 volt lighting Sockets: 24N, 24S & 15-pin Axles and tyres: BPW axles, air suspension, with disc brakes (377 mm), with lift/lower function Trailing steering axles with electro-magnetic reversing lock, actuated via reverse gear or manually Axle tool Tyres: 435/50 R 19.5 Accessories included: At the galvanized front connection strip: yellow-red air couplings 4 wheel chocks with brackets 2" kingpin Galvanized steel front wall approx. 1,600 mm high, EN12642-XL White reflective tape to EU standards on the sides, extension section and red at the rear Loading platform with heavy-duty hardwood floor 9 pairs of stake pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform 1 spare wheel holder under the platform on the right (direction of travel) Galvanized folding supports under the rear slope of the loading area Sliding mounting rails for ALU loading ramps at the rear of the vehicle European reflective plates (red-yellow) at the rear of the semi-trailer One mudflap at the rear of the semi-trailer Bracket for a rotating beacon at the rear of the semi-trailer At the gooseneck and on the rear panel left and right, each with a bracket for warning panels including socket One HDPE toolbox 620x360x610 under the platform on the left (direction of travel) 4 pairs of WADER container locks in the platform for 1x 20ft container or 1x 40ft container; additional locking position in the extension for a 45ft container 3 pairs of transverse stake pocket rails on the platform for 100 x 50 mm plug-in stanchions Lift axle on the front axle with control via TEBS E, depending on current axle load and loading condition Speed stickers 80 km/h on the rear and both sides Four warning boards extendable by approx. 400 mm, approx. 423 x 423 mm, with LED position light. Mounting for rotating beacon on warning boards Load gauge including axle load diagram HRM metallization (High Resistance Metallisation) of the outer frame Complete steel structure shot blasted, then specified visible surfaces metallized

Stanje: novo, lastna masa: 10.600 kg, največja dovoljena obremenitev: 35.400 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.500 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 940 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Loading area: - Loading deck in extendable design - Loading deck with hardwood planks, rear bevel approx. 500 mm x 8° - 2 pairs of lashing rings (LC 5,000 daN) - 1 pair of lashing rings (LC 10,000 daN) - 6 pairs of outward-folding lashing rings (LC 5,000 daN) - 3 pairs of outward-folding lashing rings (LC 10,000 daN) - Cut-outs in the loading deck's external frame for attaching tension belts Braking system: - Braking system in accordance with EU regulations, with EBS-E (2S2M) Painting: - First-class, durable corrosion protection for the standard shot-blasted welded frame guaranteed by a two-component (2K) zinc-rich primer - High-quality two-component (2K) top coat in solid Novagrey - Rear section metallised and painted in RAL 9010 (pure white) - Metallic paint not available Landing gear: - JOST mechanical landing gear with 2-speed gearbox, 24t lifting capacity (test load 50t) Steel construction: - Steel structure made from high-strength fine grain steels - Steel grades: Pgsdpfxjl Ux Rws Am Tol - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system according to EU regulations, LED lighting 24 Volt - Sockets: 2x 7-pin & 15-pin Axles and tyres: - BPW axles, air suspended, with disc brakes (377 mm), with lifting/lowering function - Hydro-mechanically forced steering - Axle tools - Twin tyres 235/75 R 17.5 Accessories included: - Yellow-red air couplings at the galvanised front connection bar - 4 wheel chocks with holder - 2" king pin - Galvanised steel headboard approx. 1600 mm high - White reflective tape on the sides, sliding section and rear in red in accordance with EU regulations - Loading deck with heavy-duty hardwood floor - Rear and front steering by cable - Remote control via push buttons, with single-track monitoring of the axles - With wireless remote control for rear steering - 9 pairs of stake pockets for 100 x 50 mm plug-in stakes on the outer frame of the loading deck - Galvanised folding supports under the loading deck bevel - Sliding mounting rail for aluminium loading ramps at the rear of the vehicle - European reflective panels (red-yellow) at the trailer rear - One mud flap at the trailer rear - Mount for a beacon at the trailer rear - Mounts for warning boards including socket on gooseneck and rear panel, each left and right - Stainless steel toolbox INOX 1,500 x 390 x 810 under the loading deck, right side in driving direction - Central lubrication system BEKAMAX (Pico) with NLHI-2 multipurpose grease and removable protection around pump - 6 pairs of WADER container locks on the loading deck for 1x 20ft, 2x 20ft or 1x 40ft containers, additional locking for one 45ft container in extendable section - 4 pairs of crosswise stake pocket strips mounted in the loading area for 100 x 50 mm plug-in stakes - Lift axle on the first axle, controlled by TEBS, dependent on current axle load and load condition - 80 km/h speed stickers at the rear and on both sides - Four extendable warning boards ca. 400 mm (approx. 423 x 423 mm) with LED position light - Beacon mount on the warning boards - Load gauge for axle load determination, including load diagram - HRM metallisation (High Resistance Metallisation) on the external frame - Complete steel construction shot-blasted, then all defined visible areas metallised with ZINACOR 850 (85% zinc, 15% aluminium) by thermal spraying

Stanje: novo, lastna masa: 11.300 kg, največja dovoljena obremenitev: 36.700 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.250 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 r 22,5, barva: sivo-črna, Oprema: ABS, Loading platform: Loading platform in extendable design with pneumatically operated locking mechanism A fixed intermediate table, approx. 250 mm wide, is mounted on the central beam 8 pairs of lashing rings, foldable outwards (LC 5,000 daN) 3 pairs of lashing rings, foldable outwards (LC 10,000 daN) Pgjdpfshlz Shsx Am Tsl Openings in the outer frame of the loading platform for attaching tensioning straps (LC 2,000 daN) Axles and tyres: BPW axles and suspension, all axles with hydro-mechanical forced steering Disc brakes, technical axle load: 10,000 kg Air suspension with lift and lower valve Axle tools 6 tyres, size 385/65 R 22.5 Brake system: Brake system according to EU regulations with EBS-E (2S2M) Landing gear: JOST landing legs (mechanically operated) with 2-speed gearbox for 24 t lift load (50 t test load) Steel construction: Steel construction made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical system: Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX mounted on the front terminal board with 24N, 24S & 15-pin sockets Connections according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: First-class, long-lasting corrosion protection of the standard grit-blasted welded frame, guaranteed by a 2-component (2K) zinc-dust primer High-quality, single-colour 2-component (2K) top coat in Novagrau Rear section metallised and painted in RAL 9010 (pure white) No metallic paint finish possible Included accessories: At the gooseneck and at the rear plate, left and right, each with a bracket for warning signs, including socket Remote steering from the front and rear via cable remote control with push buttons, with single-track control of the axles Electro-hydraulic unit 4 wheel chocks with brackets on the front wall 2" kingpin A galvanised steel front wall approx. 2,200 mm high Yellow-red air couplings on the galvanised front terminal board White reflective tape on the side, at the extension and rear in accordance with EU regulations, red at the rear European reflective plates (red-yellow) on the rear of the trailer One mud flap on the rear of the trailer Manual and documentation Bracket for a revolving warning light at the rear of the trailer Loading platform with approx. 30 mm thick wooden floor set in omega profiles 10 pairs of stake pockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading platform 1 spare wheel holder under the loading platform on the right-hand side in the driving direction 6 pairs of WADER container locks in the loading platform, for 1x 20ft container, 2x 20ft containers or 1x 40ft container; in the extension, an additional locking position is provided for a 45ft container 5 pairs of stake pocket strips, mounted transversely in the loading platform, for plug-in stanchions 100 x 50 mm A galvanised bracket mounted transversely under the loading platform (2,390 x 720 x 400 mm) Access ladder mounted on the right in the direction of travel One HDPE toolbox 1,200x500x480 mounted at the front under the loading platform on the left in the direction of travel Lift axle on the front axle with control via TEBS E depending on the current axle load and loading status Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable protection around the pump Red/white reflective tape on the extension of the loading platform On the central beam,

Stanje: novo, lastna masa: 9.450 kg, največja dovoljena obremenitev: 35.550 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.500 mm, širina tovornega prostora: 1.560 mm, skupna širina: 2.550 mm, velikost pnevmatike: 385/65 R 22,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck designed as a loading platform with aluminum chequer plate covering - Front chamfered approx. 45° - Hydraulic lifting arm, lifting and lowering range approx. -280/+250 mm Pgodjygvc Hepfx Am Tsl - Two king pin positions at DSR 2,300 and 2,000 mm - Compatible with tractor units: 4x2, 6x2, or 6x4 Loading Bay: - Loading bay, length approx. 9,500 mm, fitted with angle profiles at the bottom for pallet accommodation (distance from king pin to center of axle assembly approx. 8,000 mm) Axles, Suspension, and Tires: - BPW axle stubs with drum brakes and independent wheel suspension, hydraulic axle leveling with lifting and lowering function - Lowering lock on axles in case of suspension hose rupture, designed for maximum pallet height of 150 mm - Tires: 385/65 R 22.5 - TPMS tire pressure monitoring sensors installed in all wheels including spare wheels - TPMS system in accordance with ECE R 141 Surface Treatment: - Complete steel structure, shot-blasted automatically after welding - Second blasting with corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for maximum corrosion protection - Final coating with two layers of 2K topcoat, single-color in Novagrau (DB 7350) - Paint system tested with salt spray test according to ISO 9227-NSS; cavity sealing with special wax Included Accessories: - Steel front wall, plug-in, approx. 400 mm high - Toolbox with lid, integrated in the rear area of the gooseneck, approx. 640 x 700 x 215 mm - Plug-in ALU rear wall on the gooseneck, approx. 400 mm high, anodized - 1 pair of foldable ALU side boards on the gooseneck, approx. 400 mm high, anodized - 2" king pin - 3 pairs of recessed lashing rings on the gooseneck (LC 6,300 daN) - Front connector strip with yellow-red air couplings; illuminated operation for gooseneck, suspension, and hydraulic bracing, with on/off switch - Mechanical drop-leg supports for approx. 48,000 kg support load - Access ladder mounted front right, with 2 plug-in handrails - WABCO Roll Stability Support (RSS) - On the longitudinal beams, 9 pairs of lashing rings (LC 6,300 daN) - On the longitudinal beams, a grating platform level with the load securing rails - Hydraulic preinstallation including control unit for installation of 3 pairs of our hydraulic load restraints - First and last axle, left and right, manually liftable - Storage box behind axle assembly, left and right, splash-water protected - Rear chamfer for easier pallet insertion - Eyes on the rear crossmember for mechanical bracing - 7-pin socket on rear crossmember - Electro-hydraulic unit - 4 wheel chocks with holders - 2 axle load gauges mounted on the left side including axle load chart - 3 pairs of hydraulic load restraints with swivel arm, adjustable on the longitudinal beams - Rear door with cross bracing, hinged left and hydraulically locked right, horizontally lockable at 90°, 105°, and 270° - Folding underrun protection for transporting up to 4 empty standard pallets - 1 spare wheel - License plate bracket with lighting, rear left on trailer - Round NATO socket on the front connector strip (Maeler & Kaege VG 96 917) - Central lubrication system with 1 pump, BEKAMAX brand, standard grease execution

Stanje: novo, največja dovoljena obremenitev: 48.300 kg, skupna masa: 71.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete vehicle inventory, including vehicles available immediately and at short notice, can be found on our website. Below is an excerpt from the equipment list. Full specification available upon request. GOOSENECK: * Gooseneck with integrated single-axle running gear (pendulum axle) in a detachable version * Gooseneck hydraulically liftable and lowerable, including hydraulic connection linked to the hydraulic axle compensation of the first axles * Length: approx. 5,200 mm, with front tapering approx. 60° * Fifth wheel load according to data sheet: W25-DSR2700-12/22.7 * For tractor units: 6 x 4 or 8 x 4 * Steel front wall, plug-in type, approx. 400 mm high, with beveled design Psdpfxsyhkqns Am Togl * 1 pair of mechanical supports at the front of the gooseneck * ASPÖCK-UNIBOX on the front connector panel with 24N, 24S & 15-pin sockets * 1 spare wheel holder inside the front wall of the gooseneck with jib * 2 pairs of recessed lashing rings on the gooseneck (LC 2,500 daN) * 2 pairs of recessed lashing rings on the outer frame of the running gear at the front, foldable outward (LC 10,000 daN) * 1 pair of lashing rings at the transition from running gear to loading platform (LC 10,600 daN) * On the gooseneck 1 pair of removable aluminum drop sides, approx. 400 mm high, anodized * On the gooseneck 1 removable aluminum rear wall, approx. 400 mm high, anodized * 3.5 inch kingpin * TPMS tire pressure monitoring system according to ECE R 141 * Round NATO socket on the front connector panel (Maeler & Kaege VG 96 917) * 1 stainless steel toolbox with 1 lid, mounted on the gooseneck on the right in the direction of travel by the aluminum drop side, approx. 1,350 x 400 x 400 mm (L x W x H) LOADING PLATFORM: * Low-bed with external beams, designed as a telescopic loading platform in low-profile design with front extension including fixed approx. 50 mm thick hardwood floor * Length x width approx. 8,000 mm x 2,740 mm * Mechanical bolt-lug coupling from low-bed to running gear for swapping the loading platform or installing extension beams * One locking position approx. every 500 mm on the extension * 4 pairs of recessed lashing rings fitted flat in the loading platform along the outer frame/external beams (LC 10,000 daN) * 1 lashing ring each on the left and right outer rear cross member (LC 10,000 daN) * Foldable extensions, approx. 230 mm per side (WITHOUT wooden boards) * Loose extension planks, steel-rimmed * Preparation for installation of bolted container positions for 1x 20’ or 1x 40’ container on the outer beams. Without container locks * 6 pairs of threaded blocks between the lashing rings under the top chord of the outer beam for mounting bolted M24 rings (LC 8,000 daN) * 2 pairs M24 bolt rings (LC 8,000 daN) included REAR RUNNING GEAR: * Rear running gear with closed outer frame, checker plate decking and continuous prism-shaped excavator trough, approx. 1,450 x 900 x 505 mm, open at the rear * PENDULUM AXLE, all axles hydro-mechanically forced-steered * Hose rupture valve on axle compensation cylinder with automatic reset function * Hydraulic cylinders with shut-off valves and foreplugs to secure in raised position * Final paint of axles in 2 layers of 2-component paint, single color, DB 7350 Novagrau * Technical axle load: 12,000 kg each * Hydraulic axle compensation * 245/70 R 17.5 3PMSF, brand at our choice * Remote steering from front and rear via cable control, with axle alignment check, no installation in the tractor unit * 4 pairs of hanging la

Stanje: novo, lastna masa: 6.350 kg, največja dovoljena obremenitev: 38.650 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22,5, Oprema: ABS, Loading Platform: - 2 pairs of folding external lashing rings (LC 5,000 daN) - 24 pairs of cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) Landing Legs: - JOST mechanical landing legs with 2-speed gearbox, 24 t lifting capacity (50 t test load) Axles and Tyres: - BPW axles, air suspended, with disc brakes (430 mm), lift/lower function - Tyres: 385/65 R 22.5 Braking System: - WABCO braking system compliant with EU regulations featuring EBS-E (2S2M) Paintwork: - Premium and durable corrosion protection of the standard grit-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) top coat in single-tone MB 7350 Novagrau - Rear section metallized and painted in RAL 9010 (pure white) - Metallic paintwork not possible Steel Construction: - Steel construction made from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical System: - Electrical system in accordance with EU regulations - Lighting: 24 volt - ASPÖCK-NORDIK (ASS3) Pgodpfjiu Etkjx Am Tjl - ASPÖCK-UNIBOX at the front connection bar with 24N, 24S, and 15-pin sockets - Connection standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Accessories included: - Yellow-red air couplings at the galvanized front connection bar - 4 wheel chocks with holders - 2" king pin - Galvanized steel front wall approx. 1,600 mm high, EN12642-XL - White reflector tape according to EU regulations, lateral and rear red - European reflective panels (red-yellow) at the rear of the trailer - Loading platform with approx. 30 mm thick hardwood flooring, framed in omega profiles - 10 pairs of stanchion sockets for 100 x 50 mm plug-in stakes in the outer frame - 3 pairs of transverse stanchion rack strips, fitted in the loading platform, for 100 x 50 mm plug-in stakes - Bracket for 1,000 mm plug-in stakes, rear in the central beam - 1 spare wheel carrier under the loading platform on the right hand side - 1 mudflap at the rear of the trailer - Manual and description on USB stick - Bracket for beacon at the rear of the trailer - Holders for warning signs including socket at the gooseneck and left/right rear panel - 6 pairs of WADER container locks on the loading platform for 1x 20ft, 2x 20ft, or 1x 40ft container, flush with rear - 80 km/h speed stickers at the rear and both sides - Four warning signs, extendable by approx. 400 mm, approx. 423 x 423 mm, with LED position light - Load gauge for axle load determination including load diagram - HRM (High Resistance Metallisation) of the outer frame - Complete steel structure is grit blasted, then defined visible surfaces are metallized with ZINACOR 850 (zinc 85% - aluminium 15%) by hot coating

Stanje: novo, lastna masa: 8.300 kg, največja dovoljena obremenitev: 36.700 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.080 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R 22.5, barva: siv, Oprema: ABS, dvižna zadnja plošča, Loading platform: Loading platform in extendable design with pneumatically operated locking mechanism Cutouts in the outer frame of the loading platform for attaching lashing straps Landing legs: JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity Axles and tires: BPW axles, air-suspended, with disc brakes (430 mm), with lift/lower function Trailing steering axle with electromagnetic reverse lock, activated via reverse gear or manually Axle tools Tires 385/65 R 22.5 Braking system: WABCO braking system in accordance with EU regulations with EBS-E Paintwork: Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer A high-quality single-color 2-component topcoat in MB 7350 Novagrau Rear section metallized and painted in RAL 9010 No metallic paint available Steel construction: Steel construction made of high-strength fine-grained steels Steel grades: S355J2+N / S355MC S690QL / S700MC Electrical system: Electrical system in accordance with EU regulations Lighting: 24 Volt ASPÖCK-NORDIK ASPÖCK-UNIBOX at the front connection bar with 24N, 24S and 15-pin sockets Connection according to ISO Accessories included: Front galvanized connection bar with yellow-red air couplings One galvanized steel front wall approx. 1,600 mm high, EN12642-XL 4 wheel chocks with holders White reflector tape according to EU regulations on the sides, on the extension, and in red at the rear European reflective plates at the rear of the trailer Loading platform with approx. 30 mm thick hardwood floor enclosed in omega profiles 10 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading platform 1 spare wheel holder under the loading platform, right-hand side in the direction of travel Manual and description One holder for a rotating beacon at the rear of the trailer On the gooseneck and each side of the rear plate (left and right), a bracket for warning panels incl. socket Anti-slip sand layer painted onto the central beam 6 pairs of WADER container pockets in the loading platform, for 1x 20ft container, 2x 20ft containers, or 1x 40ft container; the extension includes an additional locking point for one 45ft container 4 pairs of transverse stake pocket rails mounted in the loading platform for plug-in stakes 100 x 50 mm One galvanized holder transversely under the loading platform, 2,390 x 720 x 400 mm Access ladder mounted right-hand side in direction of travel Front axle lift axle with control via TEBS E depending on current axle load and load status Load manometer for determining axle loads, including load chart Pedpfsikyh Hex Am Tjgl HRM metallization of the outer frame: complete steel structure shot-blasted, then the defined visible surfaces metallized hot-finished with ZINACOR 850

Stanje: novo, lastna masa: 10.000 kg, največja dovoljena obremenitev: 41.600 kg, skupna masa: 51.600 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Loading Platform: - Gooseneck, length approx. 4,100 mm with central beam - Extendable loading platform, length approx. 9,500 mm with rear taper approx. 350 mm x 10° and integrated hook-on bar for attaching loose ALU approach ramps - Pneumatic locking system with conical locking bolts and reinforced locking positions - Supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles, Suspension, and Tyres: - BPW axles and suspension, all axles hydro-mechanically forced steered - Mounted on turntable - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - Tyres 235/75 R17.5, twin-mounted Pgjdpfjiuy Nlox Am Tjl Paintwork: - 6-coat surface treatment - Complete steel structure shot-blasted after welding - One coat of zinc-based primer, one coat of adhesion primer - Final paintwork with 2 layers of 2-component (acrylic) paint, single colour in MB 7350 Novagrau, followed by cavity sealing with special wax Steel Structure: - Steel structure made from high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355MPa) - S690QL/S700MC (yield strength 690MPa) - Welders certified according to DIN-EN 287-1 - Welding process MAG according to EN ISO 4063, shielding gas M21 according to EN ISO 14175 Accessories: - Steel front wall, approx. 1,600 mm high - Round NATO socket at the front connection strip - 3 kW electro-hydraulic unit for controlling hydraulic functions - 4 pairs of recessed lashing rings in the outer frame of the gooseneck - 4 pairs of stake pockets integrated into the outer frame of the gooseneck for stakes approx. 100x50 mm - 1 transverse stake pocket strip mounted in the floor of the gooseneck for stakes approx. 100x50 mm (1x rear on gooseneck) - 2'' kingpin - Mechanical landing legs with 2-speed gearbox and hand crank - JOST Module B – static test load = 50,000 kg - On the gooseneck and loading area, approx. 32 mm wooden flooring in ALU-omega profiles - One locking position on the extension, approx. every 500 mm - 10 pairs of recessed folding lashing rings in the outer frame of the loading area, folding outwards - 6 pairs of stake pockets integrated into the outer frame of the loading area for stakes approx. 100x50 mm - 2 transverse stake pocket strips mounted in the floor of the loading area for stakes approx. 100x50 mm - INOX toolbox approx. 1,250 x 500 x 550 mm - Tapered end crossmember of the vehicle, approx. 350 mm 10° - Integrated hook-on bar for loose ALU approach ramps at the rear crossmember of the vehicle - 1 pair of drop tube supports at the rear crossmember - Mudguards on all axles - Central lubrication system with 1 pump - Remote steering from front and rear operable via cable remote control with push button, including single-track monitoring of the axles - Under the gooseneck and at the rear crossmember, left and right, each with a 7-pin socket for warning panels - One 7-pin socket at the rear crossmember - Container locks "TWIST-LOCKS" in the loading area for transport of 2x 20ft and 1x 40ft containers - Radio remote control for rear steering in addition to cable remote control, with 2 indicator lights on the receiver for single-track monitoring - 2 axle load gauges + axle load diagram - 4 warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Standard HRM Metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible areas hot-coated in metallic finish using ZIN

Stanje: novo, največja dovoljena obremenitev: 36.020 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 435/50 R 19.5, barva: siv, Oprema: ABS, Loading platform: - Loading platform in extendable design with pneumatically operated locking mechanism - 2 pairs of lashing rings (LC 5,000 daN) - 1 pair of lashing rings (LC 10,000 daN) - 6 pairs of fold-out lashing rings (LC 5,000 daN) - 2 pairs of fold-out lashing rings (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for attaching tension belts Axles and tires: - BPW axles, air-suspended, with disc brakes (377 mm), equipped with lifting/lowering function - Self-steering axles with electromagnetically controlled reverse lock, activated via reverse gear or manually - Axle tools - Tires: 435/50 R 19.5 Brake system: - Brake system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - Premium, durable corrosion protection for the standard shot-blasted welded frame by means of two-component (2K) zinc dust primer - High-quality two-component (2K) top coat in solid Novagrau - Rear end metallized and painted in RAL 9010 (pure white) - Metallic paint not available Landing gear: Pgodpfji Dwlwex Am Tol - JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Steel construction: - Steel structure made of high-strength fine-grained steels. - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDICK (ASS3) lighting - ASPÖCK-UNIBOX on the front connection console with 24N, 24S & 15-pin sockets - Connections according to ISO standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Accessories included: - Yellow-red air couplings at the galvanized front connection strip - 2 wheel chocks with holder - 2" kingpin - A galvanized steel front wall approx. 1,600 mm high - Yellow reflective tape as per EU regulations, on the sides, on the extension and at the rear of the trailer - European reflective signs (red-yellow) at the rear of the trailer - Loading area with approx. 38 mm thick hardwood floor - 10 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame of the platform - 1 spare wheel holder beneath the loading area on the right in the direction of travel - User manual and documentation on USB stick - One mudflap at the rear of the trailer - Bracket for a revolving beacon at the rear of the trailer - On the gooseneck and on the rear panel, left and right, each a bracket for warning boards including socket - One INOX toolbox transversely mounted beneath the platform (1,000x400x2,500mm) - 6 pairs of WADER container locks in the platform for 1x 20ft container, 2x 20ft containers or 1x 40ft container; an additional locking point is provided in the extension for a 45ft container - 3 sets of crosswise post pocket bars mounted in the platform for 100 x 50 mm plug-in posts - 60 km/h speed sticker on the rear - 2 reversing spotlights mounted on the rear panel - Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light - Mounting bracket for rotating beacon on the warning sign - HRM metallization (High Resistance Metallisation) of the outer frame - Entire steel structure shot-blasted, the defined visible surfaces then hot-finished with ZINACOR 850 metallisation (zinc 85% - aluminum 15%)