Platforma

Faymonville 3-Achs-Mega-Tele-Plateau zwangsgelenkt

Stanje: novo, največja dovoljena obremenitev: 50.400 kg, skupna masa: 65.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment specification. Full specification available on request. GOOSENECK * Gooseneck in SNT design to optimize platform length, approx. length 3,700 mm, with rear bevel of approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX at the front connection rail with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, except for hydraulic winches * 1 pair of detachable ALU side walls, approx. 400 mm high, anodized finish * 1 detachable ALU rear wall, approx. 400 mm high, anodized finish * Over the gooseneck, approx. 40 mm thick hardwood flooring, over the king pin with checker plate covering * 2-inch king pin * Mount at the rear of the gooseneck for ALU drive-on ramps * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) LOAD PLATFORM * Extendable load platform, approx. length 8,800 mm, with rear bevel approx. 500 mm x 10° * Recess in platform and rear bevel for accommodating an excavator dipper stick, approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st axle self-steering, all other axles hydro-mechanically forced steered Itodotx Nwnepfx Ab Uer * 1st axle with electromagnetic reversing lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with lift and lower valve * Tires: 235/75 R 17.5 3PMSF twin tires * Mechanical landing legs with 2-speed gearbox and crank, JOST Modul B - static test load = approx. 50,000 kg * Platform with continuous and between-axles interrupted 50 mm thick hardwood flooring (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable galvanized side extensions by approx. 230 mm each side (without wooden planks) * Wheel wells with square climbing strips, approx. 15 x 15 mm in front of the axles, continuous opening up to the cross member of the gooseneck, approx. 700 x 410 mm (W x D) * ALU covers for the wheel wells, usable as bridging elements for the extension OR as width extension planks * Lockable aluminium elements on the extension tubes of the side extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel wells with square climbing strips, approx. 15 x 15 mm between the 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * ALU covers for the wheel wells, usable as bridging elements for the extension OR as width extension planks * Lockable aluminium elements on the extension tubes of the side extensions * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with single-track monitoring of the axles, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-part steel ramps, type: DR-15/60-900-4350-KG-HV-M, approx. length 4,350 mm and width approx. 900 mm * Hydraulically folding ramp tips * Ramps hydraulically adjustable individually by approx. 235 mm outward and approx. 215 mm inward * Super Grip rubber surface approx. 25 mm and steel surface approx. 5 mm as additional

Stanje: rabljeno, Leto izdelave: 1999, Payload: 19,990 kg Gross vehicle weight (GVW): 8,010 kg Front tire condition: 70% Rear tire condition: 70% Front tires: 245/70 R 17.5 Itedpoutw I Nofx Ab Uor Rear tires: 245/70 R 17.5 For further information, please contact PFEIFER GROUP.

Stanje: novo, največja dovoljena obremenitev: 36.020 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 435/50 R 19.5, barva: siv, Oprema: ABS, Loading platform: - Loading platform in extendable design with pneumatically operated locking mechanism - 2 pairs of lashing rings (LC 5,000 daN) - 1 pair of lashing rings (LC 10,000 daN) - 6 pairs of fold-out lashing rings (LC 5,000 daN) - 2 pairs of fold-out lashing rings (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for attaching tension belts Axles and tires: - BPW axles, air-suspended, with disc brakes (377 mm), equipped with lifting/lowering function - Self-steering axles with electromagnetically controlled reverse lock, activated via reverse gear or manually - Axle tools - Tires: 435/50 R 19.5 Brake system: - Brake system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - Premium, durable corrosion protection for the standard shot-blasted welded frame by means of two-component (2K) zinc dust primer - High-quality two-component (2K) top coat in solid Novagrau - Rear end metallized and painted in RAL 9010 (pure white) - Metallic paint not available Landing gear: - JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Steel construction: - Steel structure made of high-strength fine-grained steels. - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDICK (ASS3) lighting - ASPÖCK-UNIBOX on the front connection console with 24N, 24S & 15-pin sockets - Connections according to ISO standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Accessories included: - Yellow-red air couplings at the galvanized front connection strip - 2 wheel chocks with holder - 2" kingpin - A galvanized steel front wall approx. 1,600 mm high - Yellow reflective tape as per EU regulations, on the sides, on the extension and at the rear of the trailer - European reflective signs (red-yellow) at the rear of the trailer - Loading area with approx. 38 mm thick hardwood floor - 10 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame of the platform - 1 spare wheel holder beneath the loading area on the right in the direction of travel - User manual and documentation on USB stick - One mudflap at the rear of the trailer Iedpfsi Dwlwjx Ab Ujtr - Bracket for a revolving beacon at the rear of the trailer - On the gooseneck and on the rear panel, left and right, each a bracket for warning boards including socket - One INOX toolbox transversely mounted beneath the platform (1,000x400x2,500mm) - 6 pairs of WADER container locks in the platform for 1x 20ft container, 2x 20ft containers or 1x 40ft container; an additional locking point is provided in the extension for a 45ft container - 3 sets of crosswise post pocket bars mounted in the platform for 100 x 50 mm plug-in posts - 60 km/h speed sticker on the rear - 2 reversing spotlights mounted on the rear panel - Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light - Mounting bracket for rotating beacon on the warning sign - HRM metallization (High Resistance Metallisation) of the outer frame - Entire steel structure shot-blasted, the defined visible surfaces then hot-finished with ZINACOR 850 metallisation (zinc 85% - aluminum 15%)

Stanje: novo, lastna masa: 6.350 kg, največja dovoljena obremenitev: 38.650 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22,5, Oprema: ABS, Loading Platform: - 2 pairs of folding external lashing rings (LC 5,000 daN) - 24 pairs of cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) Landing Legs: - JOST mechanical landing legs with 2-speed gearbox, 24 t lifting capacity (50 t test load) Axles and Tyres: - BPW axles, air suspended, with disc brakes (430 mm), lift/lower function - Tyres: 385/65 R 22.5 Braking System: - WABCO braking system compliant with EU regulations featuring EBS-E (2S2M) Paintwork: - Premium and durable corrosion protection of the standard grit-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) top coat in single-tone MB 7350 Novagrau - Rear section metallized and painted in RAL 9010 (pure white) - Metallic paintwork not possible Steel Construction: - Steel construction made from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical System: - Electrical system in accordance with EU regulations - Lighting: 24 volt - ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connection bar with 24N, 24S, and 15-pin sockets - Connection standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Accessories included: - Yellow-red air couplings at the galvanized front connection bar - 4 wheel chocks with holders - 2" king pin - Galvanized steel front wall approx. 1,600 mm high, EN12642-XL - White reflector tape according to EU regulations, lateral and rear red - European reflective panels (red-yellow) at the rear of the trailer - Loading platform with approx. 30 mm thick hardwood flooring, framed in omega profiles - 10 pairs of stanchion sockets for 100 x 50 mm plug-in stakes in the outer frame - 3 pairs of transverse stanchion rack strips, fitted in the loading platform, for 100 x 50 mm plug-in stakes Isdoiu Etkepfx Ab Ujtr - Bracket for 1,000 mm plug-in stakes, rear in the central beam - 1 spare wheel carrier under the loading platform on the right hand side - 1 mudflap at the rear of the trailer - Manual and description on USB stick - Bracket for beacon at the rear of the trailer - Holders for warning signs including socket at the gooseneck and left/right rear panel - 6 pairs of WADER container locks on the loading platform for 1x 20ft, 2x 20ft, or 1x 40ft container, flush with rear - 80 km/h speed stickers at the rear and both sides - Four warning signs, extendable by approx. 400 mm, approx. 423 x 423 mm, with LED position light - Load gauge for axle load determination including load diagram - HRM (High Resistance Metallisation) of the outer frame - Complete steel structure is grit blasted, then defined visible surfaces are metallized with ZINACOR 850 (zinc 85% - aluminium 15%) by hot coating

Stanje: novo, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.550 mm, skupna višina: 1.040 mm, Oprema: ABS, NEW VEHICLE Kässbohrer extendable platform MEGA SPA MR3 with wheel recesses Color: Nova Grey Availability: approx. 6 months after receipt of order # Fifth-wheel load: 18,000 kg # Coupling height: 950 mm # Extendable to 6,900 mm Axles / Braking system: # BPW axles with 17.5" drum brakes # 3rd axle as trailing steering axle # 1st axle as lift axle # WABCO braking system 4S/3M # 13 x Continental HTR 2 245/70/17.5" on steel rims # Jost landing legs, 24 t capacity # 2 x 7-pin and 1 x 15-pin electrical connections # 24V lighting system by Aspöck # 2 plastic wheel chocks Equipment: # Wheel recesses with hardwood covers # Non-removable sliding table, 300 mm length # 1 pair of aluminum loading ramps, 2,400 mm long, 600 mm wide, capacity 32,000 kg included # 30 mm hardwood floor # Oversize transport kit (4x galvanized oversize plates with LEDs + 1x rotating beacon) # Toolbox mounted on the right in direction of travel # 6x2 holes for container locks, suitable for transporting 1x20", 1x40" or 1x45" containers # 4 removable container twistlocks # Stake holders mounted on the front wall, without stakes # 4 rows of stake pockets # 10 x 2 stake pockets in the frame # 8 x 2 lashing rings (10 t), 5 x 2 lashing rings (8 t), 108 lashing points in the outer frame, each rated to 2 t # Storage box for aluminum ramps under the chassis behind the third axle # Front wall 1,500 mm + 500 mm high, with Code XL certificate! # Chassis KTL coated and painted in MB7350 nova grey # Front wall MB7350 nova grey Isdpsgimw Ujfx Ab Uetr ----Subject to errors, changes, and prior sale! Location: KTH-Trailer GmbH in Goch

Stanje: novo, največja dovoljena obremenitev: 34.660 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete stock of immediately and soon available vehicles on our website. Excerpt from the equipment. Full equipment list available on request. Loading platform * Double-extendable design with pneumatically operated locking mechanism * 2 pairs of recessed lashing rings (LC 5,000 daN) * 1 pair of recessed lashing rings (LC 10,000 daN) * 7 pairs of fold-out external lashing rings (LC 5,000 daN) * 3 pairs of fold-out external lashing rings (LC 10,000 daN) * Cutouts in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Landing legs * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load) Tyres * 235/75 R 17.5 3PMSF Axles * BPW axles, hydro-mechanically forced steering * Air suspension with lift and lower valve Brake system * In accordance with EU regulations, with EBS-E (2S2M) without connecting lines to the tractor unit Steel construction * Made from high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Painting * Premium and durable corrosion protection for the standard shot-blasted welded frame is ensured by a 2-component (2K) zinc primer * High-quality 2-component (2K) topcoat, single-color in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) * Rims in silver Including accessories * Rear and front remote steering by cable remote control with push buttons, with axle tracking control (without installation in the tractor unit) * Electro-hydraulic power pack * 4 wheel chocks with holder on the front bulkhead * 2-inch king pin * At the galvanized connection bar at the front, yellow and red air couplings * Yellow reflective tape as per EU regulations on the sides, extension, and rear of the trailer * European reflective plates (red-yellow) at the rear of the trailer * One mud flap at the rear of the trailer * Manual and documentation on USB stick * Loading platform with heavy-duty hardwood floor * 10 pairs of stake pockets for plug-in stanchions (100 x 50 mm) in the outer frame of the loading platform Ijdpfx Abok Ugace Ustr * Mounting bracket for a rotating beacon at the rear of the trailer * Galvanized supports under the slope of the loading platform * A mounting bracket for a rotating beacon at the rear of the trailer * Mounting rail for aluminium loading ramps at the rear of the vehicle * 80 km/h speed stickers on the rear and both sides * Load gauge for determining axle loads including load diagram * Galvanized steel front wall (EN12642-XL), approx. 1,600 mm high * Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable protection for the pumps * Spiral cable to power the electro-hydraulic unit and/or the electric winch (approx. 35 mm², approx. 3.5 m long, max. 250 A) between trailer and tractor unit with plug connection (NATO-NATO) * Anti-slip sand layer painted on central beam * 6 pairs of WADER container pockets in the loading floor, for 1 x 20' container, 2 x 20' containers or 1 x 40' container, additional locking point in the extension section for one 45' container * 5 crosswise stake pocket bars mounted in the loading floor for plug-in stanchions 100 x 50 mm * Space for up to 9 pairs of plug-in stanchions ca. 100x50 mm, inside front bulkhead * One INOX toolbox, approx. 1,500 x 390 x 810 mm, under the loading platform on both left and right in the direction of travel * Four warning signs, extendable b

Stanje: zelo dobro (rabljeno), konfiguracija osi: 2 osi, prva registracija: 09/2018, barva: rdeča, Leto izdelave: 2018, Oprema: ABS, = Further options and accessories = - Air suspension = Further information = Rear axle 1: Twin tires Rear axle 2: Twin tires; Steerable Unladen weight: 8,940 kg Loading platform height: 90 cm Extendable body: Yes Technical condition: very good Optical condition: very good Price: On request DANSON HLB45 2-AXLE EXTENDABLE SEMI LOWLOADER 2X SAF AXLES 1X STEERING AXLE (SELF-STEERING) TIRE SIZE 245/70/R17.5 EXTENDABLE LOADING PLATFORM LENGTH 740 CM + 500 CM EXTENDABLE, TOTAL LOADING PLATFORM LENGTH 1240 CM LOADING PLATFORM WIDTH 255 CM + 2X 102.5 CM EXTENDABLE, TOTAL LOADING PLATFORM WIDTH 460 CM !!! PLATFORM HEIGHT ± 90 CM GOOSENECK 40 CM LENGTH LASHING EYES, ROPE POTS, TWISTLOCKS FOLLOW US ON INSTAGRAM: GEURTSTRUCKS WE SPEAK GERMAN HABLAMOS ESPANOL Itedpfxeux Ad Ue Ab Uer WE SPEAK ENGLISH

Stanje: novo, lastna masa: 13.250 kg, največja dovoljena obremenitev: 47.550 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, vzmetenje: zrak, velikost pnevmatike: 245/70 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings 30 mm thick hardwood flooring Extendable loading platform: Loading platform in extendable design with rear chamfer approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings 3 pairs of outward-folding lashing rings 1 pair of flat lashing rings at the front of the loading area Cut-outs in the outer frame of the loading area for inserting tension straps Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Two-part steel ramps: One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering. Ramp with hydraulically folding and unfolding parts, hydraulic lifting system, and hydraulically adjustable position. Maximum load per pair: 40,000 kg Landing legs: JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced-steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool Tires 245/70 R 17.5 Braking system: Braking system according to EU regulations with EBS-E (4S3M) without connecting lines to tractor unit Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer High-quality one-color two-component (2K) top coat in Novagrau Rear section metallized and painted in RAL 9010 (pure white) Metallic paint not possible Electrical system: Electrical system according to EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connections conforming to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" kingpin One galvanized steel headboard approx. 400 mm high At the galvanized front connection strip, yellow-red air couplings 4 wheel chocks with holders at the headboard Itsdjl Uxdkopfx Ab Uor One spare wheel with holder in front of the headboard Electro-hydraulic power unit Rear and front remote steering via cable remote control with push-buttons, with single-track control of the axles Bracket at rear of gooseneck for ALU drive-on ramps European reflector signs (red-yellow) at trailer rear White reflective tape according to EU regulations at the sides, at the extension, and red at the rear At the gooseneck and on the ramps left and right, each with a holder for warning signs including socket One holder for beacon at trailer rear Galvanized folding supports under the loading platform chamfer Ramp operating valves fitted on the right side of the trailer Cover plates to bridge the gap between ramps and loading platform One mudflap at trailer rear Manual and description on USB stick Central lubrication system BEKAMAX (Pico) with general-purpose grease NLGI-2 and removable pump guard On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm The rear galvanized stakes are removable, superstructure length approx. 2,560 mm One INOX toolbox 1,350 x 400 x 400 on the gooseneck, box covers oil filler cap 4 pairs of WADER container pockets in the loading area for a

Stanje: novo, lastna masa: 9.300 kg, največja dovoljena obremenitev: 38.700 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.200 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R 22,5, barva: sivo-črna, Oprema: ABS, Cargo Area: • Extendable cargo area with pneumatically operated locking mechanism • Cargo platform with approx. 30 mm thick timber flooring • 7 pairs of external folding lashing rings (LC 5,000 daN) • 3 pairs of external folding lashing rings (LC 10,000 daN) • Cutouts in the outer frame of the cargo area for attaching tensioning straps (LC 2,000 daN) Axles and Tyres: • BPW axles and suspension, all axles hydromechanically forced-steered • Equipped with disc brakes • Technical axle load: 10,000 kg • Air suspension with lift and lower valve • Axle tool kit • Tyres: 385/65 R 22.5 • TPMS tire pressure monitoring system compliant with ECE R 141 Brake System: • WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Electrical System: • Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) • ASPÖCK-UNIBOX at the front control strip with 24N, 24S & 15-pin sockets • Connections as per ISO standards • 24N ISO-1185 • 24S ISO-3731 • 15-pin ISO-12098 Standard Accessories Included: • Remote-controlled steering from front and rear via cable remote control with push buttons, including single-track axle monitoring • 4 wheel chocks with holders mounted on the front wall • 2" king pin • One galvanized steel front wall, approx. 1,600 mm high • Yellow-red air couplings at the galvanized front connection strip • White reflective tape compliant with EU standards on both sides, on extension, and at the rear of the trailer in red • European reflective plates (red-yellow) at the rear of the trailer • One mud flap at the rear of the trailer • Operating manual and instructions • Mount for a revolving beacon at the rear of the trailer • Cargo area with approx. 30 mm thick timber floor inset in omega profiles • 10 pairs of stake pockets (100 x 50 mm) in the outer frame of the cargo bed • 1 spare wheel holder under the cargo area, right-hand side in the direction of travel • Electro-hydraulic unit • At the gooseneck and rear panel left/right, each with bracket for warning signs, incl. socket • Coated sand layer on the main beam as anti-slip protection • 6 pairs of WADER container pockets in the cargo area for 1x20ft, 2x20ft or 1x40ft containers; additional locking point provided in the extension for a 45ft container • 4 pairs of transverse stake pocket rails in the cargo area for plug-in stakes 100 x 50 mm • Access ladder mounted on the right side in the direction of travel • One HDPE toolbox approx. 1,200 x 500 x 480 mm at the front under the cargo bed, left in the direction of travel • BEKAMAX (Pico) centralized lubrication system with removable pump guard • Lift axle on front axle, controlled via TEBS E according to dynamic axle load and load status • Wireless remote control for steering, in addition to cable operation, with indicator lights on receiver for single-track monitoring • Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm, equipped with position light • Bracket for revolving beacon on the warning signs • 80 km/h speed sticker on rear and both sides • Load gauge for axle load determination, including load chart • HRM (High Resistance Metallisation) of the outer frame • Complete steel construction shot blasted; subsequently, defined visible surfaces metallised by hot-dip application with ZINACOR 850 (85% zinc – 15% aluminium) Itedpeiu Etrjfx Ab Uor

Stanje: novo, lastna masa: 11.300 kg, največja dovoljena obremenitev: 36.700 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.250 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 r 22,5, barva: sivo-črna, Oprema: ABS, Loading platform: Loading platform in extendable design with pneumatically operated locking mechanism A fixed intermediate table, approx. 250 mm wide, is mounted on the central beam 8 pairs of lashing rings, foldable outwards (LC 5,000 daN) 3 pairs of lashing rings, foldable outwards (LC 10,000 daN) Openings in the outer frame of the loading platform for attaching tensioning straps (LC 2,000 daN) Axles and tyres: BPW axles and suspension, all axles with hydro-mechanical forced steering Disc brakes, technical axle load: 10,000 kg Air suspension with lift and lower valve Axle tools 6 tyres, size 385/65 R 22.5 Brake system: Brake system according to EU regulations with EBS-E (2S2M) Landing gear: JOST landing legs (mechanically operated) with 2-speed gearbox for 24 t lift load (50 t test load) Steel construction: Steel construction made of high-strength fine-grained steels Steel grades: Itsdpfx Abshlz Shj Ujr S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical system: Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX mounted on the front terminal board with 24N, 24S & 15-pin sockets Connections according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: First-class, long-lasting corrosion protection of the standard grit-blasted welded frame, guaranteed by a 2-component (2K) zinc-dust primer High-quality, single-colour 2-component (2K) top coat in Novagrau Rear section metallised and painted in RAL 9010 (pure white) No metallic paint finish possible Included accessories: At the gooseneck and at the rear plate, left and right, each with a bracket for warning signs, including socket Remote steering from the front and rear via cable remote control with push buttons, with single-track control of the axles Electro-hydraulic unit 4 wheel chocks with brackets on the front wall 2" kingpin A galvanised steel front wall approx. 2,200 mm high Yellow-red air couplings on the galvanised front terminal board White reflective tape on the side, at the extension and rear in accordance with EU regulations, red at the rear European reflective plates (red-yellow) on the rear of the trailer One mud flap on the rear of the trailer Manual and documentation Bracket for a revolving warning light at the rear of the trailer Loading platform with approx. 30 mm thick wooden floor set in omega profiles 10 pairs of stake pockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading platform 1 spare wheel holder under the loading platform on the right-hand side in the driving direction 6 pairs of WADER container locks in the loading platform, for 1x 20ft container, 2x 20ft containers or 1x 40ft container; in the extension, an additional locking position is provided for a 45ft container 5 pairs of stake pocket strips, mounted transversely in the loading platform, for plug-in stanchions 100 x 50 mm A galvanised bracket mounted transversely under the loading platform (2,390 x 720 x 400 mm) Access ladder mounted on the right in the direction of travel One HDPE toolbox 1,200x500x480 mounted at the front under the loading platform on the left in the direction of travel Lift axle on the front axle with control via TEBS E depending on the current axle load and loading status Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable protection around the pump Red/white reflective tape on the extension of the loading platform On the central beam,