Platforma

Faymonville MAX Trailer 3-Achs-Mega-Tele-Plateau-Radmulden

Loading platform in extendable design:
Loading platform with hardwood planks, rear bevel approx. 1,000 mm x 8°
1 pair of fixed integrated wheel recesses, approx. 1,610 x 970 x 400 mm
2 pairs of lashing rings (LC 5,000 daN)
1 pair of lashing rings (LC 10,000 daN)
6 pairs of fold-out lashing rings on the outside (LC 5,000 daN)
2 pairs of fold-out lashing rings on the outside (LC 10,000 daN)
Cut-outs in the outer frame of the loading area for attaching tensioning straps (LC 2,000 daN)

Brake system:
Brake system as per EU regulations with EBS-E (2S2M)

Paintwork:
Premium, long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc-rich primer
High-quality single-colour 2-component (2K) top coat in Nova grey
Rear section metallized and painted in RAL 9010 (Pure White)
No metallic paint possible

Landing gear:
JOST mechanical landing gear with 2-speed gearbox for 24t lifting capacity (50t test load)
Pgedpfx Afek Eammj Neu

Steel construction:
Steel construction from high-tensile fine-grain steels
Steel grades:
S355J2+N/S355MC (yield strength 355 MPa)
S690QL/S700MC (yield strength 690 MPa)

Electrical system:
Electrical system according to EU regulations, 24 volt lighting
Sockets: 24N, 24S & 15-pin

Axles and tyres:
BPW axles, air suspension, with disc brakes (377 mm), with lift/lower function
Trailing steering axles with electro-magnetic reversing lock, actuated via reverse gear or manually
Axle tool
Tyres: 435/50 R 19.5

Accessories included:
At the galvanized front connection strip: yellow-red air couplings
4 wheel chocks with brackets
2" kingpin
Galvanized steel front wall approx. 1,600 mm high, EN12642-XL
White reflective tape to EU standards on the sides, extension section and red at the rear
Loading platform with heavy-duty hardwood floor
9 pairs of stake pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform
1 spare wheel holder under the platform on the right (direction of travel)
Galvanized folding supports under the rear slope of the loading area
Sliding mounting rails for ALU loading ramps at the rear of the vehicle
European reflective plates (red-yellow) at the rear of the semi-trailer
One mudflap at the rear of the semi-trailer
Bracket for a rotating beacon at the rear of the semi-trailer
At the gooseneck and on the rear panel left and right, each with a bracket for warning panels including socket
One HDPE toolbox 620x360x610 under the platform on the left (direction of travel)
4 pairs of WADER container locks in the platform for 1x 20ft container or 1x 40ft container; additional locking position in the extension for a 45ft container
3 pairs of transverse stake pocket rails on the platform for 100 x 50 mm plug-in stanchions
Lift axle on the front axle with control via TEBS E, depending on current axle load and loading condition
Speed stickers 80 km/h on the rear and both sides
Four warning boards extendable by approx. 400 mm, approx. 423 x 423 mm, with LED position light. Mounting for rotating beacon on warning boards
Load gauge including axle load diagram
HRM metallization (High Resistance Metallisation) of the outer frame
Complete steel structure shot blasted, then specified visible surfaces metallized

Oglas je bil preveden samodejno, zaradi česar je morda prišlo do napak pri prevodu.