Müller-Mitteltal Ra Prikolice nakup rabljenega (251)

Stanje: novo, največja dovoljena obremenitev: 23.500 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, * T 3: * ABS braking system * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical rear axle equalization * Side underrun protection * Swing-down supports at the rear of the chassis frame * Mechanically adjustable warning panel packages front & rear * Front closed plastic mudguards and rear straight galvanized steel skirts, each with splash guards * Reflective contour tape on sides and rear * Hinged lid (hot-dip galvanized) for the toolbox located on the turntable platform * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm – black powder-coated – mounted to the side under the chassis * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon (rotating warning light) at rear * Drawbar scissors with 40 mm towing eye and height adjustment via drawbar spring & turnbuckle * 4 stake pockets per side (stakes not included), with integrated lashing option * Load securing package consisting of: 2 lashing eyes (6.4 t) front left & right on the main frame of the turntable platform * 5 pairs of UVV folding and lowering lashing rings * Loadable in all directions and recessed into the external frame; corner loads up to 13.4 t, otherwise 10 t * 6 pairs of mechanical fold-out outriggers for total width of 3 m (not at the rear taper) * Extension boards stored in a compartment under the loading area * Digger stick rest over the rear axle up to the end beam, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings at the sides of the digger stick rest) * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable tip section and load-holding valves, hydraulically adjustable lateral ramp shift * Hydraulic flow divider in the trailer (suitable for truck hydraulic pump outputs over 40 ltr. up to max. 140 ltr./min), two-circuit hydraulics * Loading area above the turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm approach slope) * Loaded loading height approx. 860 mm +/- 30 mm adjustment unit * Chassis, turntable, fold-out outriggers, rear drop legs and drive-on ramps hot-dip galvanized Gusdpfx Astplwfjdysa * Axles, springs, drawbar scissors, air tanks, etc. painted in black * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from CW 19/2026

Stanje: novo, največja dovoljena obremenitev: 14.660 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 19.0: * Wabco EBS brake system * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes Gujdel Th Hlopfx Adysa * 2 x 10 t BPW Eco axles * Parabolic springs (110 mm wide) with tandem equalizing unit * Drawbar with 50 mm flanged tow eye and height-adjustable drawbar * Jost landing gear at the front * Rear external folding supports * Side underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED tail lights * 50 mm softwood flooring * Preparation in front of the bulkhead for retrofitting container locks * Bolted smooth sheet metal bulkhead * Sidewalls made of trapezoidal-profiled steel sheet, foldable with drop-side spring lifting device * Steel rear wall, can be inserted between the ramps (storage bracket inside front bulkhead when not in use) * Bolted rear stanchions * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to fit 3 t folding lashing rings every 600 mm * In each front and rear corner 1 x 10 t lashing ring; various holes in the front and rear crossmember for 1.2 t lashing options * Profifix lashing rail mounted centrally along longitudinal axis, lashing capacity up to LC 3000 daN * One-piece mechanical grid ramps with spring mechanism for single-person operation, approx. 2,750 x 620 mm (can be pushed together to 20 mm) * Rear drive-on slope approx. 860 mm * Chassis, drawbar, bulkhead, rear wall, ramps, and folding supports hot-dip galvanized * Platform sidewalls painted in RAL 9010 pure white * Sidewalls can be painted in any RAL color at extra cost * Axles, springs, air tank, flanged tow eye and landing gear painted black * New vehicle with full manufacturer’s warranty * Errors and prior sale excepted * Available approx. from week 21/2026 * Example images

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profile 30.0: * EBS brake system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical rear axle equalizer * Side underrun protection * Swivel supports at rear of chassis frame * Mechanically adjustable warning sign packages front and rear * Front axle: enclosed plastic mudguards; rear axle: straight galvanized steel skirts, each with splash protection * Reflective contour tape on sides and rear * Foldable galvanized lid for tool box on turntable platform * Multi-voltage system * LED tail lights * Removable beacon at rear * Drawbar with 40 mm towing eye and height adjustment via draw spring & turnbuckle * 15-pin power socket Gujdpjl Th Adjfx Adyoa * Four stake pockets per side (stakes not included), each suitable for lashing * Load securing package consisting of: 2 lashing eyes (6.4 t) front left & right on main frame of turntable platform, 5 pairs of UVV folding and lowerable lashing rings (loadable in all directions and recessed in external frame – in corners 13.4 t, otherwise 10 t) * 6 pairs of mechanical folding outriggers for up to 3 m total width (not in rear taper) * Widening planks stored in the center of the loading platform * Digger arm support over rear axle up to end cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings laterally in the digger arm support) * Single-piece hydraulic loading ramps (approx. 3,000 x 720 mm) * 4-section valve block for retrofitting hydraulic ramp lateral adjustment * Mechanical lateral ramp shift * Loading area over turntable: approx. 1,960 x 2,520 mm * Unladen loading height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height approx. 910 mm (incl. 860 mm approach slope) * Chassis, turntable, drawbar, and loading ramps hot-dip galvanized * Axles, springs, air tanks etc. painted in black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * --Gross weight of 30,000 kg technically feasible-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from CW 18/2026

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring actuators * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Last axle self-steering with electro-pneumatic steering lock ----Suspension: * Air suspension with lift and lower system plus RtR valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control unit mounted on the trailer as an infotool with pressure sensors to display total axle load * 15-pin power connector * LED lighting system 12/24V * Removable LED beacon at the rear left ----General fittings: * Side underrun protection * Landing gears at the front and mechanical swiveling supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder mounted on the right side under the chassis ----Low-loader platform: * Saddle platform with 45° chamfered front corners and front tool box made of galvanized sheet steel (W = 2,480 x H = 500 x L = 665 mm) with folding lid * 400 mm high, foldable and removable aluminum side boards (RAL 9010 pure white) on the saddle platform * Rear wall -150 mm- plugged in at the back * Rear slope on the saddle platform to the low-bed approx. 700 mm long * Saddle platform with 50 mm wooden planks and low-bed platform with 60 mm wooden planks * Tread plate above the axles ----Extensions: * 8 x mechanical folding extensions up to 3 m overall width, but not in the rear slope (extension planks available with storage on the saddle platform) * Mechanically adjustable warning sign packages at the front and rear ----Load securing (Lashing package): * On the saddle platform, 2 x 6.3 t lashing points each as well as 3 x 5 t lashing bars on each side of the outer frame * On the low-bed platform, 2 x 13.4 t lashing rings on each side as well as 4 x 10 t lashing rings, pivoting and retractable, integrated in the outer frame * 2 x 6.4 t lashing eyes on each side as well as 1 lashing point in the excavator stick recess at the rear * 2 x container locks directly after the gooseneck on the low-bed platform ----Excavator stick recess: * Excavator stick recess from the end of the last rigid axle via the steering axle to the rear cross member, continuous with internal reinforcement profile approx. L = 2,450 x W = 770 mm x D = 270 mm ----Drive-on ramps: * Mechanical one-piece hot-dip galvanized hydraulic drive-on ramps approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way control block for future customer-side retrofit of hydraulic ramp adjustment * The outer slat of the drive-on ramp is made of 50 mm hardwood * Climbing strips on the outer frame of the ramp and on the drive-up slope ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump capacity in the truck between 40 and 120 l/min) ----Loading dimensions: * Loading area saddle platform: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Loading height unladen approx. 910 mm (incl. 860 mm drive-on slope) ----Fifth wheel height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractors) ----Paintwork: * Chassis, drive-on ramps, rear folding supports, extension brackets hot-dip galvanized * Axles, landing gears, air tanks painted in a black tone * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer warranty * Subject to errors and prior sale * Sample images may include equipment not matching the offered vehicle Gedpfxopk D I Aj Adyeua ----Delivery time: * Available

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, TS 3 Profile 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Last axle is self-steering with electro-pneumatic steering lock ----Suspension: * Air suspension with lifting and lowering system and Ride-on-Road (RtR) valve ----Electrical / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control box mounted on the trailer as an information tool, with pressure sensors for total axle load display * 15-pin power connector * LED lighting system 12 / 24V * Removable LED beacon at the rear left ----General Attachments: * Lateral underrun protection * Landing legs at the front and mechanical swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder underneath the chassis, right side ----Low Loader Platform: * Fifth wheel platform with 45° chamfered front corners and front toolbox made from galvanized sheet steel, B = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm high aluminum side walls (RAL 9010 pure white) on the fifth wheel platform, foldable and removable * Rear end wall -150 mm- inserted high * Rear slope on the fifth wheel platform to the low bed, approx. 700 mm long * Fifth wheel platform with 50 mm wooden planks and low loader deck with 60 mm wooden planks * Checker plate over the axles ----Extensions: * 8 x mechanical folding extensions to a total width of 3 m, not on the rear slope (extension planks available and stowed on the fifth wheel platform) * Mechanically adjustable warning sign packages front and rear ----Load Securing (Lashing Package): * On the fifth wheel platform: 2 x 6.3 t lashing rings per side, and 3 x 5 t lashing bars on the outer frame * On the low-bed platform: 2 x 13.4 t lashing rings per side, plus 4 x 10 t swivel-mounted and retractable lashing rings recessed in the outer frame * 2 x 6.4 t lashing eyes per side, and 1 lashing ring at the rear in the excavator stick recess * 2 x container locks immediately after the gooseneck on the low-bed platform ----Excavator Stick Recess: * Excavator stick recess from the end of the last rigid axle, over the steering axle, to the end cross member, continuous with internal reinforcement profile, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Access Ramps: * Mechanically single-piece, fully hot-dip galvanized hydraulic ramps approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way control block for future customer-side retrofitting of hydraulically movable ramps * The outer board of the access ramp is made of 50 mm hardwood * Climbing bars on the outer frame of the ramp and on the approach slope ----Hydraulics: * Hydraulic flow divider in the trailer (for truck hydraulic pump flows from 40 l to 120 l/min) ----Loading Dimensions: * Fifth wheel platform loading area: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Unladen loading height approx. 910 mm (including 860 mm slope) ----Coupling Height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractors) ----Paintwork: * Chassis, access ramps, rear folding supports, extension consoles hot-dip galvanized Gjdel Tnvgspfx Adyeua * Axles, landing legs, air tanks painted in black * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Sample images may show equipment not included in the offered vehicle ----Delivery Time: * Available from c

Stanje: novo, največja dovoljena obremenitev: 8.750 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Reference number for inquiries: 11599 * NEW VEHICLE now available immediately from stock in Alsdorf * Versatile applications: construction, landscaping, agriculture, and forestry – usable as a tipper or low-loader Müller-Mitteltal KA-TA-R 11.9 Tandem Low-Loader Three-Way Tipping Trailer with Ramps * Tyres: 385/55 R19.5 (set of 4), BPW axles, parabolic springs, drum brakes * Tyre pressure monitoring system * GVW: 11,900 kg, Payload: 8,750 kg * EBS multi-voltage system for towing vehicles with 12V and 24V electrics (e.g. agricultural and forestry vehicles) * Side marker lights with indicator trigger * LED lighting system for 12V+24V with 1x 15-pin connection cable and 1 additional cable, 12V 13-pin version with dummy sockets for both electrical plugs * Hot-dip galvanized floor, 5m x 2.42m x 0.5m, laser-welded side walls, swingable, foldable and removable, preparation for later installation of side wall extensions * Lockable compartment under the tipping platform for loading ramp storage * Including aluminum ramps, 8t capacity, 3.57m long, stored in ramp bay under the tipping body * Front wall hot-dip galvanized * 4 UVV lashing rings LC 5000daN at front and rear + 8 recessed, foldable lashing eyes LC 3000daN evenly spaced in the tipping floor * Drawbar continuously height-adjustable, hot-dip galvanized, towing eye 40mm * Net hooks * Bolted, galvanized rear stakes * ---- * We are a Müller-Mitteltal dealer! Request a quote from us! * For example: from €519 net/month on 60 months, no down payment, no residual value. An offer from our financing partner FM LeasingPartner ----Our business hours Gedpfx Adeyhtwwjyjua Monday – Thursday: 08:00 – 17:00 Friday: 08:00 – 15:00 Outside business hours, we are available by appointment. We speak German, English, Polish, and French WhatsApp Leasing, financing, and trade-in possible----

Stanje: rabljeno, največja dovoljena obremenitev: 29.750 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 03/2010, naslednji pregled (TÜV): 05/2026, Mera-B 11.750 mm Lastna teža 10.250 kg Obremenitev osi 2 x 10.000 kg Nakladalna dolžina nad vrtečo ploščo 2.400 mm vklj. 350 mm poševnine Nakladalna dolžina 7.700 mm vklj. 900 mm poševnine Višina nalaganja 880 mm Širina 2.550 mm, razširljivo na 3.000 mm Utornica za odlaganje izkopalnega kraka (DxŠxV cca 2.500 x 740 x 180 mm) SAF osi z zračno vzmetenjem 2-delne hidravlične rampe, 2.100 mm + 2.000 mm dolge, 650 mm široke vklj. Rampe hidravlično nastavljive Hidravlična podpora zadaj Gsdjxpmmmopfx Adyeua Izsek za kolo za drugo osjo Izsek za sprednje kolo, zgoraj dolžina cca 2.000 mm x 1.100 mm, spodaj globina cca 350 mm Izseki za kolesa med 3. in 4. osjo Izsek za zadnje kolo, zgoraj dolžina cca 1.300 mm x 550 mm, spodaj globina cca 220 mm

Stanje: novo, največja dovoljena obremenitev: 10.970 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, KA-TA-R 14.4 - LKW tandem trostrani kiper - Nosivost serijski cca: 11.050 kg - Povećanje ukupne dozvoljene mase na 14,4 t kod guma 285/70R19.5 - Unutrašnje dimenzije: 5.000 x 2.420 x 500 mm - Visina poda pod opterećenjem: 1.040 mm - 1 šasija sa zaštitom od podletanja, vruće pocinkovana - Lakiranje: osovine sa oprugama, vazdušni rezervoari itd. u crnoj boji - 3 para upuštenih i preklopnih veznih kuka u čeličnom podu, LC 3.000 daN - ABS 2S/2M, 24 volti - 2 podizne opruge za čelične bočne stranice visine 500 mm - 1 centralno zaključavanje levo i desno, njihajuće kod nepreklopnih bočnih stranica Dodatna oprema: 1 par UVV veznih prstenova upuštenih u čelični pod, umesto na čelični pod 1 čelični pod od Hardoxa 450, debljine 4 mm Podešavanje visine vučne ruke preko ugaonog prenosa sa ručnim pogonom umesto serijskog 1 par alu rampi bez ivica (8,0 t/par), 3.500 x 400 x 105 mm pogodno za pneumaticima i guseničarima Kutija za alat Guedpfx Aoxmwiysdyoa

Stanje: rabljeno, največja dovoljena obremenitev: 22.000 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2008, Oprema: ABS, Vehicle identification number: WMM0000080052540 STRAIGHT LOADING PLATFORM Container locking device Unladen weight: 8,000 kg Gedpfxstuhv Rj Adyoua German roadworthiness test (HU): due Gigant axles with drum brakes Air suspension Platform dimensions: 9,400 mm – Loading height: 880 mm – For further measurements see image No. 4 Extendable to 3,000 mm with lighting Drawbar – 50 mm Hydraulic ramps, split – Length: 2,600 + 1,600 mm – Width: 650 mm Support legs Tyres: 235/75 R 17.5 Subject to prior sale, modifications, and errors. This description serves for general identification of the vehicle only and does not constitute a warranty in the legal sense. The details specified in the sales contract are binding. Our offer generally does not include a new roadworthiness test (TÜV). If a new inspection is required, we will be happy to provide an offer from our partner workshops. Vehicle may feature advertising decals and/or inscriptions. Our general terms and conditions of delivery and payment apply.

Stanje: rabljeno, največja dovoljena obremenitev: 14.900 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 02/2010, naslednji pregled (TÜV): 05/2025, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.550 mm, skupna širina: 2.550 mm, skupna višina: 1.300 mm, Leto izdelave: 2010, Oprema: ABS, MÜLLER MITTELTAL RA18 Trailer for Swap Containers with External Rollers 5,500 mm – 7,000 mm, German trailer, second owner Technical Data Suitable for containers with external rollers, internal length 5,500–7,000 mm, for rear loading. Dimensions: - Gross weight: 18,000 kg - Unladen weight: approx. 3,100 kg - Payload: approx. 14,900 kg - Overall length: approx. 9,400 mm - Overall width: 2,550 mm - Tyres: 385/55R22.5, approx. 40–70% tread Features: - ABS/EBS connection according to ISO 7638 (5- or 7-pin) - Chassis main frame with raised outer rails for container guidance, hot-dip galvanized - Container locking: The roll-off container is secured at 4 points by 2 pneumatic clamping units. After sliding on the container, the 4 securing claws are closed by activating a valve, clamping the container to the chassis frame. To the front, the container is additionally secured by 2 insertable lock parts (with holders), which can be positioned at various points along the guide rails. - 2x 9t BPW 420 mm drum brake axles with air suspension - Air suspension with lowering function - Frame: welded steel construction - Brake system: two-line EBS-compliant (EU standard) - DUOMATIC coupling head - Spring-loaded parking brake - Electrics: 24 volts - Multi-chamber rear lights - 15-pin plug with connecting cable - Lighting according to EU regulations - Rims: factory silver - Underrun protection: aluminum profiles - Wheel chocks with holders - 1/2 shell plastic mudguards - Toolbox (approx. 800x300x500 mm) Condition commensurate with age and mileage! Gsdpfxjvg T Nyo Adysua Delivery available at extra cost All information subject to change! Sale to businesses or for export only! NOTE: PRICE IS NET PLUS VAT German, English: JOSEF WhatsApp: We speak: German, Czech, Polish, Romanian, Russian, English

Stanje: rabljeno, skupna masa: 47.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2004, naslednji pregled (TÜV): 08/2026, * Müller Mitteltal TS3 nizkopodni polpriklopnik * Prva registracija: 11/2004 * 3 osi * Zračno vzmetenje * Gigant osi * Hidravlične dolge rampe, pomične in zložljive * Razširitve iz 2,50 m na 3,0 m širina nakladalnega prostora * Nakladalna dolžina: 8,50 m pri nakladalni višini 0,85 m * Nakladalna dolžina na vratu: 3,40 m pri nakladalni višini 1,50 m * Podpore * Neto teža: 10.260 kg * Tehnično dovoljena skupna masa: 47.000 kg * TÜV veljaven do: 08/2026 Guedpow Tgkbsfx Adyja * Tehnični pregled do: 02/2026

Stanje: novo, največja dovoljena obremenitev: 10.360 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-ER 14.4: ----Brakes: * Electronic Brake System (EBS) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * Gigant axles ----Suspension: * Air suspension with lift and lower facility ----Drawbar / Flange Eye: * Drawbar height adjustable by approx. 300 mm * 40 mm flange drawbar eye ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System with in-cab display via EBS signal; no truck-side installation required) * LED lighting system * 15-pin power connector ----General Attachments: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding support legs at the rear * Plastic toolbox, front right, mounted outside on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * 50 mm softwood flooring * Provision for retrofitting 20" container locks at front and rear * Bolted bulkhead made of smooth sheet steel * Fold-down side walls, trapezoidal profile, with drop-side spring assists * Bolted, hot-dip galvanized rear stanchions ----Load Securing: * Outer frame with holes, approx. 45° angled, 2 t lashing capacity every 480 mm * Option to install 3 t recessed lashing rings every 600 mm * Each of the front and rear corners fitted with 1 x 6.3 t lashing ring * Various holes in front and rear cross members for 1.2 t lashing options ----Ramps: * 1 pair of aluminium loading ramps, approx. 3,310 x 400 mm (load capacity 8 t per pair), suitable for pneumatic and tracked vehicles; stowed at the rear in a compartment integrated below the deck in the chassis ----Paintwork: * Hot-dip galvanized chassis, drawbar, bulkhead, and rear wall * Vehicle fully hot-dip galvanized ----Information: * New vehicle with manufacturer’s warranty * Subject to error and prior sale Gsdpfopk D Dqox Adyeua ----Delivery Time: * Available immediately ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.360 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-ER 14.4: ----Braking System: * Electronic Braking System (EBS) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * Gigant axles ----Suspension: * Air suspension with lifting and lowering system ----Drawbar / Towing Eye: * Drawbar height-adjustable by 300 mm * 40 mm flange towing eye ----Electrics / Lighting: * TPMS (tire pressure monitoring system with indicator function in the truck via EBS signal—no installation required on the truck side) * LED lighting system * 15-pin electrical connector ----General Accessories: Gsdpfjndpn Sox Adysua * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding supports at the rear * Plastic toolbox mounted front right on the front wall * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * 50 mm softwood floorboards * Preparation for subsequent installation of 20" container locks at front and rear * Bolted, smooth sheet metal front wall * Side walls made of trapezoidal-profiled steel, foldable with drop-side spring assist * Hot-dip galvanized bolt-on rear stanchions ----Load Securing: * Perforated outer frame, angled at approx. 45 degrees, with 2 t lashing points every 480 mm * Option for 3 t folding lashing brackets every 600 mm * 1 x 6.3 t lashing ring in each front and rear corner * Various holes in front and end crossmembers for 1.2 t securing points ----Ramps: * 1 pair of aluminum loading ramps, approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles, stored in a compartment underneath the loading area in the chassis, accessible from the rear ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, front wall, and rear wall * Entire vehicle hot-dip galvanized ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex works Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 14.300 kg, skupna masa: 20.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2023, naslednji pregled (TÜV): 11/2026, Leto izdelave: 2023, * HL - TA 20.0 Gujdpfsyfy Rrjx Adysa ----Brakes: * Wabco EBS-E braking system * Emergency release device for spring-loaded cylinders * Drum brakes * Duomatic brake coupling ----Axle: * 2 x SAF axles * 1st axle as lift axle (fully automatic) * Lift axle with +30 mm ride height via actuating cylinder * Start-assist for maneuvering and forced lowering onto the first axle, controlled via speed-dependent EBS-E electronics (no installation required on the truck side, additionally with cable for control from the tractor) ----Air Suspension: * Air suspension with lowering function via remote control ----Drawbar / Flange Eye: * 50 mm flange bolt towing eye - height adjustable by +77 mm and -33 mm - for 2 t support load ----Electrics / Lighting: * 15-pin power connector * 3-pin 12V auxiliary connector * LED lighting system 12 / 24V * 2 LED reversing lights, controlled via reverse gear * EBS multi-voltage system for towing vehicles with 12 & 24V electrics * Extended connector cables for agricultural and forestry vehicles * Radio remote power supply 12+24V via tail lamp ----General Attachments: * BPW landing gear at the front * Mechanically extendable underrun protection for container lengths over 6,000 mm * Speedline diamond aluminum rims * Removable pin-type towing coupling (use permitted only when underrun protection is retracted) * Closed plastic half-shell single mudguards * Two-step access in front of the front wall on the left * Shovel and broom holder in front of the front wall * 2 stainless steel toolboxes (matte), approx. 650 x 350 x 320 mm, located on the right side * Closed side underrun protection usable as advertising space ----Hydraulics: * 2-circuit hydraulic connections (engine side, from truck/tractor), designed for 180 bar (for tractor operation) * Double-acting control circuit for hydraulic tailgate (mounted right front) with operation via radio remote control ----Hooklift: * Palfinger PHT 20 SCASNSLD5 telescopic hooklift unit (serial no. 100746129, year 2023) * Base frame made of high-strength fine-grain steel * 20,000 kg pulling force * Hook height 1,570 mm * Hooklift control via radio remote control * Radio control with fast-lowering only during unloading, not during lifting * Emergency stop switches on both left and right sides * Container bearing with 4 supports on each side and 1 roller each at the rear * Hydraulic rear internal locking * 2 additional hydraulic cylinders to assist main boom lifting * 2 x mechanical drop-down supports at the rear * Certified for 20 t gross weight (2 x 9 t axles) and 2 t nose weight * Note: If the radio control is outside the charging cradle, the service brake must be applied in order to enable the remote operation. Brake couplings must always be connected to allow the hydraulic/pneumatic valves to open * Monitoring system for underrun protection to ensure it is retracted when tipping ----Loading Height: * Unladen approx. 1,300 mm with lift axle lowered ----Finish: * Chassis, drawbar, access step, underrun protection, and drop-down supports hot-dip galvanized * Axles, air reservoir, and landing gear at the front painted black * Palfinger hooklift painted in black/yellow ----Information: * Errors and prior sale excepted * Vehicle is in very good / as-new condition ----Container Dimensions: * Load compartment length: 5,500 mm * Load compartment width: 2,300 mm * Load compartment height: 1,000 mm Information: * Mounting fittings for hook systems available

Stanje: rabljeno, največja dovoljena obremenitev: 14.300 kg, skupna masa: 20.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2023, naslednji pregled (TÜV): 11/2026, Leto izdelave: 2023, * HL - TA 20.0 ----Brakes: * Wabco EBS-E braking system * Emergency release system for spring-loaded cylinders * Drum brakes * Duomatic brake connection ----Axles: * 2 x ton SAF axles * 1st axle as lift axle (fully automatic) * Lift axle with ride height +30 mm via positioning cylinder * Starting aid for shunting and mandatory lowering on the first axle – controlled via speed-dependent EBS electronics (no installation required on the truck; also with cable for operation from the tractor) ----Air Suspension: * Air suspension with lowering function via radio remote control ----Drawbar / Flange Drawbar Eye: * 50 mm flange-mounted drawbar eye, height-adjustable by +77 mm and -33 mm, for 2 t support load ----Electrics / Lighting: * 15-pin power connector * 3-pin 12V auxiliary connector * LED lighting system 12 / 24V * 2 LED reversing lights, switched via reverse gear * EBS multi-voltage system for towing vehicles with 12 & 24V electrics * Extended connecting cables for agricultural and forestry vehicles * Power supply for radio remote: 12+24 V via taillight ----General Attachments: * BPW landing leg at the front * Mechanically extendable underrun protection for container lengths over 6,000 mm * Speedline diamond-finish aluminium wheels * Split-pin towing coupling (use only with retracted underrun protection) * Enclosed plastic half-shell single mudguards * Two-step access before the front bulkhead on the left side * Shovel and broom holders in front of the front bulkhead * 2 matte stainless steel toolboxes, approx. 650 x 350 x 320 mm, mounted right side Godox Dp Atopfx Adyjua * Enclosed side protection usable as advertising space ----Hydraulics: * 2-circuit hydraulic connections (engine end from truck/tractor), rated for 180 bar (tractor operation) * Double-acting control circuit for hydraulic tailgate (mounted front right), operated via radio remote control ----Hooklift: * Palfinger PHT 20 SCASNSLD5 telescopic hook system (Serial no. 100746129, year 2023) * Base frame made of high-strength fine-grained steel * 20,000 kg pulling force * Hook height 1,570 mm * Control of hooklift via radio remote control * Remote control with rapid function when lowering, not when raising * Emergency stop switches left and right sides * Container supports with 4 lateral supports per side and one roller at the rear * Hydraulic rear internal locking * 2 additional hydraulic cylinders to assist in lifting the main arm * 2 x mechanical fall supports at the rear * Approval for 20 t gross vehicle weight (2 x 9 t axles) and 2 t support load * Note: If the radio remote is outside the charging cradle, the service brake must be applied for radio release. Brake connections must remain connected at all times so the hydraulically/pneumatically operated valves can be opened. * Monitoring system for underrun protection to ensure it is retracted when tipping ----Loading Height: * Unladen approx. 1,300 mm with lowered lift axle ----Paintwork: * Chassis, drawbar, access steps, underrun protection, and fall supports hot-dip galvanized * Axles, air tanks, front landing gear painted black * Palfinger hooklift painted black/yellow ----Information: * Errors and prior sale reserved * Vehicle is in very good / as-new condition ----Delivery time: * Vehicle is immediately available

Stanje: rabljeno, največja dovoljena obremenitev: 14.300 kg, skupna masa: 20.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2023, naslednji pregled (TÜV): 11/2026, Leto izdelave: 2023, * HL - TA 20.0 ----Braking System: * Wabco EBS-E braking system * Emergency release device for spring brake cylinders * Drum brakes * Duomatic brake connection ----Axle: * 2 x ton SAF axles * 1st axle as lift axle (fully automatic) * Lift axle with driving height +30 mm via positioning cylinder * Traction aid for shunting purposes and forced lowering onto the first axle – controlled via speed-dependent EBS electronics (no installation required on truck side, additionally supplied with cable for operation from the tractor) ----Air Suspension: * Air suspension with lowering function via radio remote control ----Drawbar / Flange Eye: * 50 mm flange screw drawbar eye – height adjustable by +77 mm and -33 mm – for 2 ton support load ----Electrics / Lighting: * 15-pin power connector * 3-pin 12V auxiliary connector * LED lighting system 12 / 24V * 2 LED reversing lamps activated by reverse gear * EBS multi-voltage system for towing vehicles with 12 & 24V electrical systems * Extended connection cables for agricultural and forestry vehicles * Power supply for radio control 12+24V via tail light ----General Attachments: * BPW landing gear at the front * Mechanical, extendable underrun protection for container lengths over 6,000 mm * Speedline diamond-cut aluminium wheels * Pin-type towing coupling (use only when underrun protection is retracted) * Closed plastic half-shell individual mudguards * Two-step access in front of the front bulkhead on the left * Shovel and broom holder in front of the front bulkhead * 2 matt stainless steel toolboxes, approx. 650 x 350 x 320 mm, right side mounted * Closed side underrun protection can be used as advertising space ----Hydraulics: * 2-circuit hydraulic connections (engine-side from truck/tractor) designed for 180 bar (tractor operation) * Double-acting control circuit for hydraulic rear door (mounted front right) operated via remote control ----Hooklift: * Palfinger PHT 20 SCASNSLD5 telescopic hooklift device (serial no. 100746129, year 2023) * Base frame made of high-strength fine-grain steel * 20,000 kg tractive force * Hook height 1,570 mm * Hooklift operated via radio remote control * Radio remote control with fast function during tipping, but not during winching * Emergency stop switches on both left and right sides * Container bed with 4 side supports each and one roll at the rear * Hydraulic rear internal locking * 2 additional hydraulic cylinders to assist with raising the main arm * 2 x mechanical folding rear supports * Approval for 20 ton gross weight (2 x 9 ton axles) and 2 ton support load * Note: If the radio control is outside the charging cradle, the service brake must be engaged to enable remote operation. Brake connections must remain connected at all times to operate the hydraulic/pneumatic control valves. * Monitoring system for underrun protection to ensure it is retracted while tipping ----Loading Height: * Unladen approx. 1,300 mm with lift axle lowered ----Paintwork: * Chassis, drawbar, access steps, underrun guard, and folding supports hot-dip galvanized * Axles, air tanks, and front landing gear painted in black * Palfinger hooklift painted in black/yellow ----Information: Gedpox Dp Agsfx Adysua * Subject to errors and prior sale * Vehicle in very good / like-new condition ----Delivery Time: * Vehicle immediately available

Stanje: rabljeno, največja dovoljena obremenitev: 14.300 kg, skupna masa: 20.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2023, naslednji pregled (TÜV): 11/2026, Leto izdelave: 2023, * HL - TA 20.0 ----Braking System: * Wabco EBS-E electronic braking system * Emergency release device for spring-actuated cylinders * Drum brakes * Duomatic brake connection ----Axle: * 2 x 9 t SAF axles * 1st axle as a lift axle (fully automatic) * Lift axle with +30 mm ride height via actuating cylinder * Start assist function for maneuvering and forced lowering on the first axle - controlled via speed-dependent EBS electronics (no truck-side installation required, additionally equipped with cable for operation from the tractor) ----Air Suspension: * Air suspension with lowering function via remote control ----Drawbar / Flange Eye: * 50 mm flanged drawbar eye – height adjustable by +77 mm and -33 mm – for 2 t vertical load ----Electrics / Lighting: * 15-pin power connector * 3-pin 12V auxiliary connector * LED lighting system 12 / 24V * 2 LED reversing lights operated via reverse gear * EBS multi-voltage system for towing vehicles with 12 & 24V electrical systems * Extended connection cables for agricultural and forestry vehicles * Wireless power supply 12+24 V via tail light ----General Add-on Parts: * BPW support winch at the front * Mechanically extendable underrun protection for container lengths over 6,000 mm * Speedline diamond-finish aluminum rims * Pin-type towing coupling (use only when underrun protection is retracted) * Enclosed plastic half-shell individual mudguards * Two-step access in front of the front wall on the left * Shovel and broom holder in front of the front wall * 2 matte stainless steel toolboxes approx. 650 x 350 x 320 mm mounted on the right side * Enclosed side impact protection can be used as advertising space ----Hydraulics: Guedpfxox Dp Ame Adysa * Dual-circuit hydraulic connections (engine side from truck / tractor) rated for 180 bar (for tractor operation) * Double-acting control circuit for hydraulic tailgate (mounted on the right in the front area), operated via remote control ----Hooklift: * Palfinger PHT 20 SCASNSLD5 telescopic hooklift unit (Serial No. 100746129, year 2023) * Main frame made of high-strength fine-grain steel * 20,000 kg pulling force * Hook height 1,570 mm * Hooklift operation via remote control * Remote control with fast function when lowering, but not when raising * Emergency stop switch on both left and right sides * Container support with 4 supports each side and 1 roller each rear * Hydraulic rear internal locking * 2 additional hydraulic cylinders to support lifting of the main arm * 2 x mechanical fall supports at the rear * Approval for 20 t total weight (2 x 9 t axles) and 2 t vertical load * Note: If the remote control is removed from the docking station, the service brake must be engaged to activate the radio control. Brake connections must remain permanently connected to operate the hydraulic/pneumatic valves * Monitoring system for underrun protection to ensure it is retracted when tipping ----Loading Height: * Unladen approx. 1,300 mm with lowered lift axle ----Paintwork: * Chassis, drawbar, step, underrun protection, and fall supports hot-dip galvanized * Axles, air tanks, and front support winch painted black * Palfinger hooklift painted black/yellow ----Information: * Errors and prior sale excepted * Vehicle is in very good / as-new condition ----Container Dimensions: * Load length: 5,500 mm * Load width: 2,300 mm * Load height: 1,000 mm Info: * Mounting brackets for hook systems according to ...

Stanje: rabljeno, prva registracija: 11/2006, Leto izdelave: 2006, MÜLLER - MITTELTAL T4 Kompakt Vrtljiva prikolica - Nizkopodna prikolica z zračno vzmetenimi in jamskimi kolesi - 4 x zračno vzmetene GIGANT - osi - zračno vzmetenje Guedpfx Aswmpbdodyea - 4 x kolesne jame - mehanske nakladalne rampe - 2 zadnja podporna noga, zložljiva - izvlečne opozorilne table - ABS - MICHELIN pnevmatike: 235/75 R 17.5 - težka izvedba: 40.000 kg skupne mase - lastna teža: 8.400 kg - skupna dolžina: 11.750 mm - vlečna zanka: 50 mm Posebej primerna za prevoz strojev za rezanje apna! - nemška prikolica - Tehnični pregled / tehnični preizkus možen na zahtevo in za doplačilo! Pridržujemo si pravico do napak in vmesne prodaje!

Stanje: rabljeno, največja dovoljena obremenitev: 4.500 kg, skupna masa: 6.500 kg, konfiguracija osi: 2 osi, prva registracija: 07/1979, naslednji pregled (TÜV): 04/2026, dolžina tovornega prostora: 4.000 mm, širina tovornega prostora: 1.900 mm, višina nakladalnega prostora: 380 mm, skupna širina: 2.500 mm, skupna višina: 3.000 mm, Leto izdelave: 1979,

Stanje: novo, največja dovoljena obremenitev: 10.800 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: ----Braking system: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensation unit ----Drawbar / Flange eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension of 250 mm for a total length of 2,250 mm ----Electrics / Lighting: * Tyre pressure monitoring with display option in the truck cab via EBS signal – no truck-side installation required * 15-pin power connector * LED lighting system 12 / 24 V * EBS multi-voltage system for tractors with 12 and 24 V electrics ----General attachments: * Landing gear at the front * External folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, mounted front right on the bulkhead exterior * Side underrun protection * Plastic quarter mudguards ----Low-bed loading area: * 50 mm softwood floor * Pre-equipment in front of the bulkhead for subsequent installation of container locks * Bolted 400 mm bulkhead made of smooth sheet * Rear stakes bolted * Drop sides with spring-assisted lifting mechanism ----Load securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Optional installation of 3 t folding lashing rings every 600 mm * 1 x 6.3 t lashing point in each of the front and rear corners * Various drill holes in the front and rear cross members for 1.2 t lashing options * Profifix lashing rail along the centre longitudinal axis, for lashing up to LC 3,000 daN ----Ramps: * One-piece hydraulic grid ramps approx. 2,750 x 600 mm (collapsible to 20 mm spacing) Gusdpfx Aerwc R Rjdysa * Hydraulic flow divider in the trailer (when hydraulic pump output in truck exceeds 40 l/min, max. 140 l/min) ----Paintwork: * Chassis, drawbar, bulkhead, mechanical rear supports and ramps hot-dip galvanized * Axles, springs, air tanks, landing gear and flange eye painted in black * Drop sides painted in RAL 9010 pure white * Side walls available painted in any RAL colour for an additional charge ----Information: * New vehicle with manufacturer warranty * Subject to prior sale and errors ----Delivery time: * Available from approx. week 16/2026

Stanje: rabljeno, največja dovoljena obremenitev: 31.000 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 07/2024, dolžina tovornega prostora: 9.290 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 950 mm, * PT 40.0 Profile: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with raising/lowering system and RtR valve * Manometer pressure display for load weight determination (axles separated into 2 air suspension circuits) * Side underrun protection * Swing-down supports at the rear of the chassis frame * Mechanically adjustable warning panel sets front and rear * Front axle: plastic quarter mudguards with spray protection * Rear axle: straight galvanized steel skirts with spray protection Gujdpfx Asl Tlhrodyea * Reflective contour markings on sides and rear * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power connector * LED lighting system 12 / 24 V * Removable LED beacon at rear * 2 LED reversing lights (activated via reverse gear) * Tow bar with 50 mm towing eye and height adjustment * Tool box made of galvanized steel, black powder coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high * Extension in front of turntable platform approx. 490 mm long with 45° corners * ROBOTER-welded anti-slip coating on the turntable platform steel plate * Load securing package consisting of: 1 x 13.4 t UVV lashing ring front left & right in front of bulkhead support, 4 mounting holes per side in the turntable platform each with 2 t lashing capacity, 1 pair of 13.4 t lashing rings suspended at rear left & right before the rear cross member, 4 pairs of 10 t UVV lashing rings per side, swiveling and lowerable, loadable in all directions and recessed into side frame, 3 stake pockets per side with 2 t lashing option each * Hot-dip galvanized mechanical folding outriggers for 3 m overall width (not on the rear slope) * Timber plank holder for width extensions under the chassis, longitudinal left * Excavator arm rest above rear axle up to end plate, approx. 2,100 mm long and 190 mm deep, 2 pairs of 6.4 t lashing rings per side in the excavator arm rest * Hardwood flooring on the running surfaces of the low-loader platform * Hydraulically operated single-piece ramps (approx. 3,000 x 720 mm), mechanically adjustable width * Ramp outer planks made of hardwood * Steel construction prepped for 6-way control sliders * Unladen loading height approx. 950 mm +/- 20 mm (chassis) * Turntable, folding outriggers, mechanical support legs, ramps are hot-dip galvanized * -- Axles, air tanks, tow bar painted black -- * Tyres 235/75 R 17.5 * Vehicle registered for one day in 07/2024, due to missing tire pressure monitoring system and was not loaded/used * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.800 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: ----Braking system: * EBS (Electronic Braking System) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange drawbar eye: * Height-adjustable drawbar, adjustable by approx. 300 mm * Drawbar extension by 250 mm to 2,250 mm ----Electrics / Lighting: * Tyre pressure monitoring with in-cab display via EBS signal – no installation required on the truck side * 15-pin power connector * LED lighting system 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics ----General attachments: * Support winch at the front * Foldable external support legs at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, mounted at front right on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low loader platform: * 50 mm softwood floor * Prepared in front of bulkhead for retrofitting container locks * Bolted 400 mm bulkhead of smooth steel plate * Bolted rear posts * Side boards with spring assist ----Load securing: * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Option for installation of 3 t folding lashing brackets every 600 mm * One 6.3 t lashing ring in each front and rear corner * Various drilled holes in bulkhead and rear cross member for 1.2 t lashing points * Profifix lashing rail, centrally along longitudinal axis, for load securing up to LC 3000 daN ----Ramps: * One-piece hydraulic grating ramps approx. 2,750 x 600 mm (can be retracted to 20 mm clearance) * Hydraulic flow divider in trailer (for hydraulic pump output in the truck of over 40 L/min to a max. of 140 L/min) ----Painting: * Chassis, drawbar, bulkhead, mechanical drop-down supports, and ramps hot-dip galvanized * Axles, springs, air tanks, front support winch, and flange drawbar eye painted black * Drop sides painted in RAL 9010 pure white * Side panels painted in RAL colour of choice at extra cost ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Sample images ----Delivery time: Gujdperwc R Aefx Adyea * Available from approx. week 16/2026

Stanje: rabljeno, največja dovoljena obremenitev: 31.000 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 07/2024, dolžina tovornega prostora: 9.290 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 950 mm, * PT 40.0 profile: * Wabco EBS-E (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lift and lowering function as well as return-to-ride valve * Pressure gauge for axle load determination (axles separated into 2 air suspension circuits) * Side underrun protection * Swing-out supports at the rear of the chassis frame * Mechanically adjustable warning panels front and rear * Front axle: plastic quarter mudguards with spray guards * Rear axle: straight, galvanized steel side skirts with spray guards * Reflective contour marking tape, side and rear Gujdsl Tnu Aepfx Adysa * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power connector * LED lighting system 12 / 24 V * Removable rear LED beacon * 2 LED reverse lights (controlled by reverse gear) * Drawbar with 50 mm towing eye and height adjustment * Tool box made of galvanized sheet steel, black powder coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high * Front section ahead of turntable platform approx. 490 mm long with 45° corners * ROBOT-welded anti-slip coating on the steel plate of the turntable platform * Load securing package consisting of: 1 x 13.4 t UVV lashing eye left & right in front of front bulkhead support, 4 holes per side in the turntable platform for 2 t lashing capacity each, 1 pair of lashing eyes (13.4 t) hanging at the rear left & right in front of the end support, 4 pairs per side of UVV lashing rings (10 t) that can be swivelled and lowered, loadable in all directions and recessed in the outer frame, 3 stake pockets per side with simultaneous 2 t lashing possibility * Hot-dip galvanized mechanical fold-out outriggers for 3 m overall width (not in the rear slope) * Plank holder for extensions mounted longitudinally under the chassis on the left * Excavator arm rest over the rear axle up to the end cross member, approx. 2,100 mm long and approx. 190 mm deep, with 2 pairs per side of 6.4 t lashing eyes in the excavator arm rest * Hardwood floor on the running surfaces of the low bed platform * Hydraulically operated one-piece loading ramps (approx. 3,000 x 720 mm), mechanically adjustable sideways * Outer boards of the loading ramps made of hardwood * Steel construction prepared for 6-valve control block * Loading edge unladen approx. 950 mm +/- 20 mm chassis * Turntable, fold-out outriggers, mechanical drop supports, loading ramps hot-dip galvanized * --Axles, air tanks, and drawbar painted in black shade-- * Tires 235/75 R 17.5 * The vehicle has a day registration from 07/2024, due to the lack of a tire pressure monitoring system, and has not been loaded or used * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 31.630 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.250 mm, širina tovornega prostora: 2.520 mm, * T 4: * EBS (electronic braking system) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Parabolic springs * Mechanical axle compensation front and rear * Tire pressure monitoring with display capability in the truck via EBS signal – no truck-side installation required * Warning panel packages front & rear * Reflective contour tape on sides and rear * EBS multi-voltage system for 12 & 24 V electrics * LED beacon (removable) on the rear * 24 V 15-pin, plus additional 12 V 7+4 pin power cable * Extended connection cables for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm towing eye and stepless height adjustment * Tool box made of powder-coated sheet steel and spare wheel holder in basket design, right-hand side * Closed single plastic mudguards at the front * Straight steel rear mudflaps each with spray suppression (splash suppression) * Side underrun protection * Extended drop member by 500 mm to the front * Turntable platform extended by 520 mm at the front with 45° corners and 3 integrated lockable storage compartments incl. lids * Chassis made of high-strength fine-grain steel * Floor over turntable platform: 50 mm, low-loader platform: 60 mm softwood * Outer planks of the loading ramps made of 50 mm bamboo wood * Four stake pockets per side (stakes not included), each with 2 t lashing capability * Load securing package includes: 2 lashing eyes 6.4 t front left and right on main turntable frame, side front and rear each 1 pair 13.4 t lashing rings on outer frame, 4 pairs per side 10 t swiveling and lowerable lashing rings loadable from all directions recessed in outer frame, 2 pairs 6.4 t lashing rings on each side in the excavator arm rest, 8 pairs galvanized folding outriggers for 3 meter total width (not at the rear bevel) * Widening planks stowed in a compartment on the left side * Excavator arm rest above the rear axle to end of approach ramp approx. 2,300 x 740 x 190 mm Gusdporczm Dofx Adyja * Mechanical drop supports at the rear * Hydraulic, hot-dip galvanized loading ramps approx. 3,000 x 720 mm * Hydraulic lateral ramp shift via sliding pipe from ramp shaft * Loading area over slewing ring: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Loaded platform height approx. 860 mm (incl. 860 mm approach ramp) * Chassis, turntable, loading ramps, mechanical folding supports rear hot-dip galvanized * Axles, springs, air reservoir and slewing ring painted in black tone * New vehicle with manufacturer's warranty * Errors and interim sale reserved * Available from CW 21 / 2026

Stanje: novo, največja dovoljena obremenitev: 10.760 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: ----Brakes: * Drum brakes * Electronic Braking System (EBS) * Emergency release device for spring-loaded cylinders ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange Drawbar Eye: * Height-adjustable drawbar (adjustable by 300 mm) * Drawbar extension by 250 mm to a total length of 2,250 mm * 40 mm flange drawbar eye ----Lighting / Electrics: * Tire Pressure Monitoring System (TPMS) * LED lighting ----General Attachments: Gjdsrvvfljpfx Adysua * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding supports at the rear * Plastic toolbox mounted front right on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood flooring * Preparation for subsequent mounting of container locks in front of the bulkhead * Bolted smooth sheet steel bulkhead * Side walls made of trapezoidal-profiled steel, foldable with board wall spring lifts * Steel rear wall, slidable between the ramps — storage bracket for unused rear wall in front of the bulkhead * Bolted rear stakes ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing force every 480 mm * Option to fit 3 t folding lashing rings every 600 mm * 1 x 6.3 t lashing ring in each of the front and rear corners * Various drill holes in the header and tail member for 1.2 t lashing options ----Ramps: * One-piece mechanical grating ramps with spring assembly for single-person operation, approx. 2,750 x 600 mm (can be collapsed to 20 mm) * Rear access slope approx. 860 mm ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, bulkhead, loading ramps, and rear wall * Drop side color in RAL 9010 pure white * Painting of the side walls in an RAL color of your choice available for an additional charge ----Information: * -- Reinforced and certified body according to EN 12642 XL incl. load securing certificate -- * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available from week 08/2026