Priklopnik z delovno ploščadjo

MÜLLER-MITTELTAL T4 40,0 , Agrar, hydr. Rampen,3 m. Paket

Stanje: novo, največja dovoljena obremenitev: 31.630 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 9.250 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T 4: * EBS (Elektronisches Bremssystem) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Parabolic springs * Mechanical axle compensation front and rear * Tire pressure monitoring with display option in the truck via EBS signal - no truck-side installation required * Warning sign packages, front and rear * Reflective contour tape on sides and rear Fpjdpfx Afsl Th Evs Ujn * EBS multi-voltage system for 12 & 24 V electrics * Removable LED beacon at the rear * 24 V 15-pin as well as additional 12 V 7+4-pin power cable * Extended connection cables for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm towing eye and infinitely adjustable height * Tool box made of powder-coated sheet steel and spare wheel holder in basket design on right side * Enclosed single plastic mudguards at the front * Straight steel mud flaps at the rear each with splash protection (spray suppression) * Side underrun protection * Extended offset cranking by 500 mm forward * Kingpin platform extension by 520 mm with 45° angled corners and 3 recessed lockable storage compartments with lid * Chassis made from high-strength fine-grained steel * Flooring over turntable platform made of 50 mm and in low-bed platform made of 60 mm softwood * Outer boards of the drive-on ramps made of 50 mm bamboo wood * Four stake pockets per side (stakes not included) with integrated 2 t lashing point * Load securing package (Lasi package) including: 2 lashing eyes (6.4 t) front left/right on the main frame of the turntable platform; on both sides, front and rear, 1 pair of 13.4 t lashing rings on the outer frame, 4 pairs per side of 10 t swivel and drop lashing rings, loadable in all directions and integrated into the outer frame; 2 pairs of 6.4 t lashing rings per side in the excavator stick tray; 8 pairs of galvanized folding extensions for total width of 3 m (not at the rear angled section) * Side extension planks stored on the left in a compartment * Excavator stick rest above rear axle up to the end of approach slope, approx. 2,300 x 740 x 190 mm * Mechanical drop supports at rear * Hydraulic, hot-dip galvanized drive-on ramps approx. 3,000 x 720 mm * Hydraulic side ramp shifting on sliding tube from ramp axle * Loading area above kingpin: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Loaded platform height approx. 860 mm (incl. 860 mm approach slope) * Chassis, kingpin platform, drive-on ramps, mechanical folding supports at rear hot-dip galvanized * Axles, springs, air tanks, and kingpin painted in black tone * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, lastna masa: 7.500 kg, največja dovoljena obremenitev: 36.500 kg, skupna masa: 44.000 kg, konfiguracija osi: > 3 osi, dovoljena osna obremenitev (os 1): 12.000 kg, dovoljena osna obremenitev (os 2): 12.000 kg, dovoljena osna obremenitev (os 3): 12.000 kg, dolžina tovornega prostora: 9.190 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, vzmetenje: jeklo-zrak, velikost pnevmatike: 235×75 R17,5, medosna razdalja: 1.310 mm, največja hitrost: 100 km/h, Leto izdelave: 2026, Oprema: ABS, osrednja vrtljiva plošča, CETRATEK TL-89/4, nizkotilni prikolica s 4 osmi – visoka nosilnost za težke transporte CETRATEK TL-89/4 je robustna nizkotilna prikolica s 4 osmi, namenjena profesionalnemu transportu gradbene mehanizacije, kmetijske tehnike in težke delovne opreme. Velika nosilna površina, robustno podvozje in obsežna serijska oprema jo naredijo vsestransko vozilo za zahtevne transporte. Tehnični podatki: * Največja možna dovoljena masa: 48.000 kg * Dovoljena masa z vlečno prikolico premera 50 mm in v skladu s členom 70: 40.000 kg * Dovoljena masa v cestnem prometu: 24.000 kg * Nosilnost pri 40.000 kg dovoljene mase: približno 29.300 kg * Največja možna nosilnost: približno 37.300 kg * Lastna teža: približno 10.700 kg * Vlečna prikolica v serijski opremi: premer 50 mm * Alternativno premer 40 mm; v tem primeru dovoljena masa v skladu s členom 70: 28.000 kg * Skupna dolžina: 11.850 mm * Glavna nosilna površina: 6.750 mm * Gosi vrat: 2.450 mm * Nakladalna ploščad: 3.000 mm * Višina ploščadi: približno 880 mm * Širina: 2.540 + 250 + 250 mm, ročno nastavljiva * Dolžina vlečne palice: 1.950 mm * Razdalja od spenjalne glave do 1. osi: 2.630 mm * Medosna razdalja sprednje osi: 1.250 mm * Medosna razdalja zadnje osi: 1.310 mm * Širina tira: 1.850 mm * Nastavljiva višina vlečne palice: 520–800 mm * Vrteči nosilec: premer 1.100 mm, SAF * Podlaga ploščadi: jeklo + 60 mm trdega lesa DABEMA * Zadnje rampe: 3.000 × 750 mm, stransko ročno pomične Podvozje in zavorni sistem: * 4 × 12.000 kg osi TRAX * Zračna vzmet * Pnevmatike 235/75 R17,5, 16 kosov * Dovoljena hitrost: 100 km/h * WABCO 4S/2M EBS * Standardna zračna sponka, DUO-MATIC opcijsko Elektrika, hidravlika in oprema: * Napetost 12 V / 24 V * LED-osvetlitev * EBS ISO 7638 * Priključki ISO 1185, ISO 3731 in ISO 12098 * Vtičnica NATO * Vodoodporni vtični priključki * Vgrajena hidravlika z 2,2-kW hidravličnim motorjem * 2 cilindra za rampe * 2 orodna predala * 2 kovinski klini * Na vsaki strani 10 pritrdilnih točk z vlečno silo 10 t Fedpfxju Rbzvo Af Uepn * 6 pritrdilnih točk na ploščadi z vlečno silo 10 t * 4 dodatne pritrdilne točke na gosi vratu Zaščita površine in garancija: Struženje jeklenih granul, dvojno nanašanje temeljnega premaza in dvoslojni akrilni premaz v barvi RAL po želji stranke. 24 mesecev garancije na podvozje in vzmetenje, 12 mesecev na električne in hidravlične komponente ter 5 let garancije za lakiranje v skladu z garancijskimi pogoji. Na voljo številne dodatne možnosti, vključno z zavoro na zadnji osi, centralnim mazanjem, hidravličnim vitlom, hidravlično podporo na zadnji strani, daljinskim upravljanjem, aluminijastimi rampami, hidravličnimi rampnimi sistemi, zaporniki za kontejnerje in pocinkanjem. Osnovna cena od 41.688,00 € neto. Pridržana pravica do sprememb cen in tehničnih podatkov ter napak. Slike so ponazorilne in lahko prikazujejo dodatno opremo oziroma opcije.

Stanje: novo, lastna masa: 7.500 kg, največja dovoljena obremenitev: 32.500 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, naslednji pregled (TÜV): 03/2023, dolžina tovornega prostora: 9.700 mm, širina tovornega prostora: 3.000 mm, višina nakladalnega prostora: 900 mm, vzmetenje: zrak, velikost pnevmatike: 235/75r17,5, Leto izdelave: 2026, Oprema: ABS, osrednja vrtljiva plošča, TOP EQUIPMENT – INCLUDING THE FOLLOWING ACCESSORIES: Chassis frame hot-dip galvanized in immersion bath Front storage box on platform, with hinged lid Rear storage box on platform, with hinged lid Recess for excavator arm storage, lowbed – rear section 3 m equipment package without ramp incline Warning package for special permit Steel sheet toolbox Stake pocket set in outer frame Basic hydraulics for truck with rear connection Hydraulic ramp lift for one-piece ramps Hydraulic lateral ramp shift Hydraulic support legs left and right 1 pair of 6t lashing rings bolted to outer frame WABCO Smart Board pre-configured Complete SSV front left HTD409525K COC certificate of conformity OPTIONAL Fodpfx Ajglbllef Uspn Rubber flooring on ramp €1,890 net Rubber flooring on the incline €1,250 net Adjustable drawbar 40 / 50 DIN

Stanje: rabljeno, največja dovoljena obremenitev: 31.000 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, prva registracija: 07/2024, dolžina tovornega prostora: 9.290 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 950 mm, * PT 40.0 Profi ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: Fpodpfxol Tlhre Af Uon * Air suspension with lifting and lowering system, including RtR valve ----Drawbar: * Drawbar with 50 mm towing eye and height adjustment ----Lighting / Electrics: * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power connector * LED lighting system 12 / 24 V * Removable rear LED beacon * 2 LED reversing lights (activated via reverse gear) ----General equipment: * Manometer - pressure gauge for load weight determination (axles separated into 2 air suspension circuits) * Side underrun protection * Swing-down supports at the rear of the chassis frame * Mechanically adjustable warning sign sets front and rear * VA plastic quarter mudguards with spray protection * HA straight galvanized steel skirts with spray protection * Reflective contour tape on sides and rear * Tool box, galvanized steel sheet, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high ----Low loader platform: * Forepart in front of the turntable platform, approx. 490 mm long with 45° corners * ROBOT-welded anti-slip surface on the steel plate of the turntable platform * Hardwood floor on the running surfaces of the low loader platform ----Load securing (La-Si package comprising): * In front of the front wall support, 1 x 13.4 t UVV lashing point each left & right * 4 lateral holes each in the turntable platform with 2 t lashing capacity each * 1 pair of lashing points (13.4 t) hanging at the rear left & right in front of the rear support * 4 pairs of UVV lashing rings (10 t) on each side, swiveling and lowering, loadable in all directions and recessed in the outer frame * 3 pockets for stanchions per side, with simultaneous 2 t lashing facility ----Widening package: * Hot-dip galvanized mechanical folding outriggers for 3 m overall width (not in the rear taper) * Plank holder for extensions under the chassis on the left, longitudinally ----Excavator arm rest: * Excavator arm rest above HA up to the end support, approx. 2,100 mm long and approx. 190 mm deep * 2 pairs of 6.4 t lashing points each side in the excavator arm rest ----Ramps: * Hydraulic one-piece approach ramps (approx. 3,000 x 720 mm), mechanically adjustable sideways * Outer planks of ramps made from hardwood * Steel structure prepped for 6-section control valve ----Loading height: * Loading edge unladen approx. 950 mm +/- 20 mm ----Tires: * 235/75 R 17.5 tires ----Paintwork: * Chassis, turntable, folding outriggers, mechanical supports, and approach ramps hot-dip galvanized * -- Axles, air tanks, drawbar finished in a shade of black -- ----Information: * Vehicle has a day registration in 07/2024 due to missing tire pressure monitoring system, and has not been loaded/used * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Immediately available from Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 31.000 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, prva registracija: 07/2024, dolžina tovornega prostora: 9.290 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 950 mm, * PT 40.0 Profi ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 4 x 11 tonne Gigant axles ----Suspension: * Air suspension with lifting and lowering system and RtR valve ----Drawbar: * Drawbar with 50 mm towing eye and height adjustment ----Lighting / Electrical: * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power connector * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (activated via reverse gear) ----General Attachments: * Manometer (pressure gauge) for load weight determination (axles separated into 2 air suspension circuits) * Side underrun protection * Swing-down supports at the rear of the chassis frame * Mechanically adjustable warning boards, front and rear * Front axle plastic mudguards with spray protection * Rear axle straight galvanized steel side skirts with spray protection * Reflective contour tape on the sides and rear * Tool box, black powder-coated galvanized steel, approx. 1,000 mm wide, 600 mm deep, 300 mm high Fodjl Tnu Aopfx Af Uspn ----Low Loader Platform: * Front extension in front of the turntable platform, approx. 490 mm long with 45° corners * ROBOT-WELDED anti-slip coating on the steel plate of the turntable platform * Hardwood flooring on the running areas of the low-bed platform ----Load Securing (La-Si package consists of): * 1 x 13.4 t UVV lashing ring left & right in front of the headboard carrier * 4 fixing holes each side in the turntable platform, each with 2 t lashing capacity * 1 pair of lashing rings (13.4 t), suspended at the rear left & right in front of the rear carrier * 4 pairs of UVV lashing rings (10 t) per side, pivotable and lowerable, loadable in all directions and recessed into the external frame * 3 stake pockets per side, each offering 2 t lashing capability simultaneously ----Widening Package: * Hot-dip galvanized mechanical folding outriggers for 3 m overall width (not in the rear slope) * Beam bracket for widenings under the chassis on the left, longitudinally mounted ----Excavator Arm Rest: * Excavator arm rest above the rear axle up to the end cross member, approx. 2,100 mm long and approx. 190 mm deep * 2 pairs of 6.4 t lashing rings per side in the excavator arm rest ----Ramps: * Hydraulically operated one-piece drive-on ramps (approx. 3,000 x 720 mm), mechanically adjustable sideways * Outer planks of the ramps made from hardwood * Steel construction prepared for 6-way control valve ----Loading Height: * Loading edge unladen approx. 950 mm +/- 20 mm ----Tyres: * Tyres 235/75 R 17.5 ----Coating/Paintwork: * Chassis, turntable, folding outriggers, mechanical supports, and drive-on ramps hot-dip galvanized * --Axles, air tanks, drawbar painted black-- ----Infos: * Vehicle has a daily registration as of 07/2024, due to the missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery Time: * Available immediately from Egestorf