Müller-Mitteltal T4 40,0 , Agrar, Hydr. Rampen,3 M. Paket nakup rabljenega (58.379)

Stanje: novo, največja dovoljena obremenitev: 31.630 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.250 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T 4: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Parabolic springs * Mechanical axle compensation front and rear * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * Warning plate sets front & rear * Contour tape on sides and rear, reflective * EBS multi-voltage system for 12 & 24 V electrical systems * Removable LED beacon rear * 24 V - 15-pin and additional 12 V - 7+4 pin power cable * Extended connection cables for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm towing eye, continuously height-adjustable * Powder-coated steel toolbox and spare wheel holder, basket design, right side * Front closed single plastic mudguards * Rear straight steel mudflaps, each with spray suppression (anti-spray) * Side underrun protection * Extended offset bend by 500 mm to the front * Turntable platform extension at the front by 520 mm with 45° corners and 3 integrated lockable storage compartments with covers * Chassis made from high-strength fine-grained steel * Decking above turntable platform from 50 mm softwood and on low loader platform from 60 mm softwood * Outer planks of loading ramps made from 50 mm bamboo wood * Four stake pockets per side (but no stakes included), each with a 2 t lashing point * Load securing package comprising: 2 lashing eyes (6.4 t) front left and right on the main frame of the turntable platform; front and rear, one pair of lashing rings (13.4 t) each on outer frame; four pairs of swivel and lowerable lashing rings (10 t) per side, loadable in all directions and integrated in the outer frame; two pairs of lashing rings (6.4 t) per side in excavator stick recess; eight pairs of galvanized folding outriggers for 3 m total width (not on the rear slope) * Widening planks stored on the left side in stowage compartment * Excavator stick recess above rear axle up to end of approach slope, approx. 2,300 x 740 x 190 mm * Mechanical drop supports rear * Hydraulic, hot-dip galvanized loading ramps approx. 3,000 x 720 mm * Hydraulic lateral ramp movement on slide pipe from ramp shaft * Loading area above fifth wheel: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Loaded deck height approx. 860 mm (including 860 mm approach slope) * Chassis, turntable, loading ramps and mechanical folding supports rear hot-dip galvanized * Axles, springs, air tanks and turntable painted in black * New vehicle with manufacturer's warranty Dcjdpfsrczm Dox Apwji * Subject to errors and prior sale * Available immediately ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 31.630 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.250 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T 4: * EBS (Elektronisches Bremssystem) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Parabolic springs * Mechanical axle compensation front and rear * Tire pressure monitoring with display option in the truck via EBS signal - no truck-side installation required * Warning sign packages, front and rear * Reflective contour tape on sides and rear * EBS multi-voltage system for 12 & 24 V electrics * Removable LED beacon at the rear * 24 V 15-pin as well as additional 12 V 7+4-pin power cable * Extended connection cables for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm towing eye and infinitely adjustable height * Tool box made of powder-coated sheet steel and spare wheel holder in basket design on right side * Enclosed single plastic mudguards at the front * Straight steel mud flaps at the rear each with splash protection (spray suppression) Dcodpfx Ajl Th Evepwsi * Side underrun protection * Extended offset cranking by 500 mm forward * Kingpin platform extension by 520 mm with 45° angled corners and 3 recessed lockable storage compartments with lid * Chassis made from high-strength fine-grained steel * Flooring over turntable platform made of 50 mm and in low-bed platform made of 60 mm softwood * Outer boards of the drive-on ramps made of 50 mm bamboo wood * Four stake pockets per side (stakes not included) with integrated 2 t lashing point * Load securing package (Lasi package) including: 2 lashing eyes (6.4 t) front left/right on the main frame of the turntable platform; on both sides, front and rear, 1 pair of 13.4 t lashing rings on the outer frame, 4 pairs per side of 10 t swivel and drop lashing rings, loadable in all directions and integrated into the outer frame; 2 pairs of 6.4 t lashing rings per side in the excavator stick tray; 8 pairs of galvanized folding extensions for total width of 3 m (not at the rear angled section) * Side extension planks stored on the left in a compartment * Excavator stick rest above rear axle up to the end of approach slope, approx. 2,300 x 740 x 190 mm * Mechanical drop supports at rear * Hydraulic, hot-dip galvanized drive-on ramps approx. 3,000 x 720 mm * Hydraulic side ramp shifting on sliding tube from ramp axle * Loading area above kingpin: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Loaded platform height approx. 860 mm (incl. 860 mm approach slope) * Chassis, kingpin platform, drive-on ramps, mechanical folding supports at rear hot-dip galvanized * Axles, springs, air tanks, and kingpin painted in black tone * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 16.000 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2024, * KA-TA-RT 21.0 ML ----Brakes: * Without ABS/EBS, approved for 40 km/h * Spring-loaded parking brake * Drum brakes ----Axles: * Gigant axles ----Suspension: * Tandem equalization unit with 100 mm wide parabolic springs ----Drawbar / Drawtube: * Fixed welded drawtube with low-maintenance ball joint for K80 ball coupling (offset by +77 mm / 33 mm via head plate), with raised bracket for connection lines ----Electrics / Lighting: * 12 V, 7 + 4 pin power supply * LED lighting system 12 / 24 V with protective grid * 2 LED work lights at the rear, switchable from towing vehicle without installation on towing side ----General attachments: * Support winch at the front * Mechanical drop-down supports at the rear * Side marker lights with indicator activation * Plastic quarter mudguards * Plastic toolbox approx. 750 x 350 x 300 mm mounted on the right side * Hot-dip galvanized two-step access ladder in front of the front wall (on FR left) ----Chassis: * Fine-grain steel chassis ----Tipper body: * Steel Pal.- 3-way tipper body with M-Strong side panels (front wall fixed, continuous side panels - without center stanchions - swinging via manual central locking and mechanically foldable with sideboard spring assistor) * Hydraulic tailgate, 500 mm high, functioning as hydraulic chute with a 115° opening angle * 4 mm Hardox 450 steel floor ----Load securing: * 1 x 7-tonne recessed and foldable lashing point in each corner * 4 x 3-tonne recessed and foldable lashing rings on each side ----Ramps: * 1 pair of aluminum drive-on ramps (10 t/pair with axle spacing over 2,500 mm), 3,570 x 410 x 120 mm, suitable for rubber-tired and tracked vehicles * 2 receiving compartments for aluminum drive-on ramps, recessed from behind into the chassis * Load securing according to EN 12642 XL ----Coupling height: * Laden approx. 530 mm & unladen approx. 590 mm ----Paintwork: * Superstructure painted RAL 9010 pure white * Chassis, drawtube, rear supports, underrun protection hot-dip galvanized * Axles, air tank, support winch at the front * K80 coupling painted in black shade ----Info: * New vehicle with manufacturer's warranty * Errors and prior sale excepted Dcjdpfxor Dpzus Apwsi ----Delivery time: * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 16.000 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2024, * KA-TA-RT 21.0 ML ----Braking System: * Without ABS/EBS, homologated for 40 km/h * Spring-loaded parking brake * Drum brakes ----Axles: * Gigant axles ----Suspension: * Tandem-balance unit with 100 mm wide parabolic springs ----Drawbar Eye / Drawbar: * Rigid, welded drawbar with low-maintenance ball joint for K80 ball coupling (adjustable by +77 mm / 33 mm via mounting plate) with elevated gallows for connection lines ----Electrics / Lighting: * 12 V 7 + 4-pin power supply cable * LED lighting system, 12 / 24 V with protective grilles * 2 LED work lights at the rear, switchable from the towing vehicle, no vehicle-side installation required ----General Attachments: * Landing gear at the front * Mechanical drop legs at the rear * Side marker lights with indicator control * Plastic quarter mudguards * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right-hand side * Hot-dip galvanized two-step access steps in front of the bulkhead on the left (FR) ----Chassis: * Chassis made from high-tensile fine-grained steel ----Tipper Body: * Steel pallet three-way tipper body with M-Strong side boards (fixed front wall, continuous sides without central stanchions, swinging via manual central locking, plus mechanically folding with board spring lifters) * Hydraulic tailgate, 500 mm high, engineered as a hydraulic chute with a 115° opening angle * 4 mm Hardox 450 steel floor ----Load Securing: * Each corner equipped with 1 x 7 t recessed folding lashing ring * Each side fitted with 4 x 3 t recessed folding lashing points ----Ramps: * 1 pair aluminum loading ramps (10 t/pair for axle spacing over 2,500 mm), 3,570 x 410 x 120 mm, suitable for rubber and tracked vehicles * 2 recessed storage compartments for aluminum ramps in the rear of the chassis Dcsdpor Dpz Hsfx Apwoi * Load securing compliant with EN 12642 XL ----Coupling Height: * Loaded approx. 530 mm & unladen approx. 590 mm ----Paintwork: * Bodywork painted in RAL 9010 pure white * Chassis, drawbar, rear support legs, underrun protection hot-dip galvanized * Axles, air tanks, landing gear (front) * K80 coupling painted in black ----Information: * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex works Egestorf

Stanje: rabljeno, lastna masa: 8.800 kg, največja dovoljena obremenitev: 31.200 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 04/1996, dolžina tovornega prostora: 10.000 mm, širina tovornega prostora: 2.510 mm, višina nakladalnega prostora: 1 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75R17.5, barva: rdeča, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Lokacija vozila: Bovenden, 4 osi, vrtljiva gred, listnato vzmetenje, razširljiv do 3 m, pritrdilna ušesa, dvo-delne nakladalne rampe, hidravlične rampe, zadnja podpora, stranska aluminijasta zaščita, dvojne pnevmatike, škatla za orodje. Nadgradnja: 4-osna nizkopodna prikolica s hidravličnimi dvodelnimi rampami. Višina nakladanja cca 900 mm. 4x SAF osi 10t, bobnaste zavore, vlečno uho 40 in 50 mm! Dolžina zgornje ploščadi cca 2900 mm! Dolžina spodnje ploščadi cca 7100 mm! PODATKI O DODATNI OPREMI BREZ GARANCIJE, spremembe, vmesna prodaja in napake pridržane! Dodpfxoywvhre Apwsci

Stanje: novo, največja dovoljena obremenitev: 23.500 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.380 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * PT 30 Profile: ----Braking System: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t Gigant axles ----Suspension: * Air suspension with lifting and lowering function as well as Return-to-Ride (RtR) valve ----Drawbar: Drawbar, 1,200 mm long with 40 mm draw eye and height adjustment via tension spring & turnbuckle ----Electrics / Lighting: * Smart Board mounted on the trailer as an information tool (for axle load display – front and rear separately) * Tire pressure monitoring system with display possibility in the truck via EBS signal, no installation required on the truck side * 15-pin power connector * LED lighting 12/24 V * LED beacon (removable) at the rear ----General Attachments: * Side underride protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages front and rear * Front axle (FA) plastic quarter mudguards with spray protection * Rear axle (RA) straight galvanized steel mudguards with spray protection * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm, powder-coated black, mounted right side * Box in rotating frame for accessories, with folding lid, 2 pcs. container locks permanently fitted (directly after the rotating frame platform) * 2 galvanized steps on the rotating frame, left and right ----Low-loader Platform: * ROBOT-welded anti-slip covering to the steel plate of the rotating frame platform (protruding weld beads) ----Load Securing (Load Securing Package consists of): * 2 lashing eyes (13.4 t) front left & right at the front wall crossmember * 1 pair of UVV lashing rings (13.4 t) at the front & rear, and 3 pairs UVV lashing rings (10 t) each side, pivotable and lowerable, loadable in all directions and recessed in the outer frame * 3 stake pockets each side with simultaneous 2 t lashing capability * Profifix lashing rail lengthwise in the center axis, in the flat area, for lashing up to LC 3000 daN ----Widening: * 6 pairs of mechanical folding outriggers for 3 m total width (not on rear slope) * Widening planks stored in the middle of the loading area ----Ramps: * Hydraulic one-piece drive-on ramps approx. 3,000 x 720 mm * Mechanically adjustable sideways * 4-way control block for future retrofitting of hydraulic ramp shifting ----Excavator Arm Rest: * Excavator arm rest over rear axle, continuous up to the end crossmember (total length approx. 2,100 mm) * 2 pairs of lashing eyes LC 6400 daN in the excavator arm rest, positioned laterally in the longitudinal frame ----Loading Height: Dedpfx Aotplwijpwoci * Loaded approx. 910 mm +/- 20 mm air suspension ----Coating/Paintwork: * Chassis, rotating frame, folding outriggers, fall supports, and drive-on ramps hot-dip galvanized * Axles, slewing ring, air tanks, drawbar painted in a black tone ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery Time: * Immediately available ex Egestorf

Stanje: rabljeno, lastna masa: 6.400 kg, največja dovoljena obremenitev: 23.600 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, prva registracija: 01/2013, dolžina tovornega prostora: 7.800 mm, širina tovornega prostora: 2.510 mm, višina nakladalnega prostora: 920 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75R17.5, barva: rumena, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Lokacija vozila: Bovenden, 3 osi, SAF osi, vrtljiva plošča, listnato vzmetenje, ABS (protiblokirni sistem), pritrdilne ušesce, dvoje deljene nakladalne rampe, hidravlične rampe, zadnja podpora, bočna aluminijasta zaščita, dvojna kolesa, zaboji za orodje. Nadgradnja: 3-osni polpriklopnik z nizkim podom s hidravlično dvoje deljeno nakladalno rampo (hidravlično zložljivo in bočno pomično), pocinkane rampe, 3x 10t SAF osi, bobnaste zavore, vdolbina za bagersko roko, 50 mm vlečni obroč! Zgornja ploščad cca 1500 mm, spodnja ploščad cca 6300 mm! Dolžina rampe cca 4200 mm! Dedoy R Ekijpfx Apwoci Za doplačilo je možna tudi primerna 40 mm vlečna palica! PODATKI O DODATNI OPREMI SO BREZ JAMSTVA, pridržujemo si pravico do sprememb, predprodaje in napak!

Stanje: rabljeno, lastna masa: 6.500 kg, največja dovoljena obremenitev: 23.500 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, prva registracija: 01/2008, dolžina tovornega prostora: 8.000 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 910 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75R17.5, barva: oranžna, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Vehicle location: Bovenden, leaf suspension, 3 axles, BPW axles, turntable, ABS (anti-lock braking system), lashing eyes, hydraulic ramps, rear supports, side aluminum underrun protection, twin tires, storage box Body: Hydraulic ramps, extendable to 3m. BPW axles, drum brakes, lashing rings on the outer sides. Ramp length approx. 4000mm! ACCESSORY DETAILS WITHOUT GUARANTEE, subject to change, prior sale, and errors excepted! Dcsdpfx Asqpgtmepwoi

Stanje: novo, največja dovoljena obremenitev: 23.500 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.380 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, PT 30 Profile: ----Braking System: * EBS (electronic braking system) * Emergency release mechanism for spring-actuated cylinders * Drum brakes ----Axle: * 3 x 11 t Gigant axles ----Suspension: Djdpfxsxptn Re Apwoci * Air suspension with lifting and lowering system, including RtR valve ----Drawbar: * Drawbar, 1,200 mm long, with 40 mm towing eye and height adjustment via traction spring & turnbuckle ----Electrical / Lighting: * Smart-Board information system mounted on the trailer (for axle load indication – separate front and rear display) * Tire pressure monitoring with display capability in the truck via EBS signal, no truck-side installation required * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear ----General Attachments: * Side underrun protection * Swing-out supports at the rear of the chassis frame * Mechanically adjustable warning board sets front and rear * Front axle plastic quarter mudguards with spray protection * Rear axle straight galvanized steel mud skirts with spray protection * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm, black powder-coated, mounted right side * Compartment in the bogie for accessories, with folding lid and 2 fixed container locks (directly behind the bogie platform) * 2 galvanized steps on the bogie, left and right ----Low Loader Platform: * Robot-welded non-slip overlay on the steel plate of the bogie platform (protruding weld seams) ----Load Securing (La-Si package consisting of): * 2 lashing eyes (13.4 t) front left & right on front bulkhead carrier * 1 pair of UVV lashing rings at front & rear (13.4 t) and 3 pairs of UVV lashing rings on each side (10 t), pivotable and lowerable, loadable in all directions, recessed in outer frame * 3 stake pockets on each side, each with 2 t lashing capacity * Profifix lashing rail in longitudinal axis, centered in flat area, for lashing up to LC 3000 daN ----Widening: * 6 pairs of mechanical folding outriggers for 3 m overall width (not in the rear taper) * Widening planks stored in the centre of the loading platform ----Ramps: * Hydraulic one-piece drive-on ramps, approx. 3,000 x 720 mm * Mechanically adjustable laterally * 4-way control block for future retrofit of hydraulic ramp lateral adjustment ----Excavator Arm Rest: * Excavator arm rest above rear axle, extending to the rear end crossmember (total length approx. 2,100 mm) * 2 pairs of lashing eyes LC 6400 daN in the excavator arm rest, located laterally in the main longitudinal frame ----Loading Height: * Loaded approx. 910 mm +/- 20 mm (air suspension) ----Paintwork: * Chassis, bogie, folding outriggers, drop-down supports and ramps hot-dip galvanized * Axles, slewing ring, air tanks, and drawbar painted in black ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 31.820 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 01/1980, dolžina tovornega prostora: 9.700 mm, širina tovornega prostora: 3.000 mm, skupna širina: 2.550 mm, skupna višina: 900 mm, Leto izdelave: 1980, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal T4 Low Loader Trailer * SAF axles with drum brakes * Twin tyres * Low bed with extendable loading platform * Hydraulic loading ramps, movable (2 units) * Drive-over gooseneck * Additional rear supports * Turntable construction ----Dimensions & loading area * Loading area approx. 9,800 mm * Loading width: 2,550 - 3,000 mm * Loading height: 900 mm ----* Permissible total weight: 40,000 kg * Payload: 31,820 kg * Tyres: 235/75R17.5 ----Vehicle number: 11892----Subject to errors and prior sale----Advertising and various lettering have been digitally removed. -----We are happy to assist you with any formalities arising from the purchase of a vehicle. Simply let us know your requirements and suggestions, and we will take care of the rest. Among other things, we can offer you the following services at an additional cost: ----Trade-in of your old vehicle TÜV/general inspection Complete export processing Financing brokerage Obtaining export license plates Vehicle transport Vehicle registration Dodsy Skl Iepfx Apwoci Recovery and vehicle transport ----Your VTS Team

Stanje: novo, največja dovoljena obremenitev: 23.940 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profi 30.0 ----Braking System: * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t Gigant axles ----Suspension: * Parabolic springs with mechanical rear axle equalization ----Drawbar: * Drawbar with 50 mm towing eye and height adjustment via draw spring and turnbuckle ----Lighting / Electrics: * RDÜ tire pressure monitoring * Multi-voltage system * LED tail lights 12 / 24 V * Rear removable rotating beacon * 15-pin power connector ----General Attachments: Dedel Th I Aepfx Apwjci * Lateral underrun protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages front and rear * Front: closed plastic mudguards; Rear: straight galvanized steel skirts, each with splash guards * Tool box made of galvanized sheet steel, black powder-coated, approx. 650 x 300 x 600 mm * Hinged lid (hot-dip galvanized) for tool box in the bogie platform * Four stake pockets per side (stakes not included), also suitable for lashing ----Load Securing (La-Si package consists of): * 2 lashing eyes (6.4 t) front left & right on main frame of the bogie platform * 6 pairs of UVV-certified lashing rings, foldable and lowerable, loadable in all directions, recessed into the outer frame * Corner load capacity 13.4 t, otherwise 10 t ----Widening: * 6 pairs of mechanical fold-out outriggers for max. overall width of 3 meters (except at the sloped rear) * Widening planks stored in the center of the loading area ----Ramps: * Hot-dip galvanized one-piece hydraulic drive-on ramps (approx. 3,000 x 720 mm), mechanically laterally adjustable * 4-way valve block for retrofit hydraulic lateral ramp shift ----Loading Area: * Over turntable: approx. 1,960 x 2,520 mm & unladen height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm & unladen height approx. 910 mm (including 860 mm drive-on slope) ----Tyres: * 235/75 R 17.5 twin tyres ----Unladen weight: * Approx. 5,980 kg unladen weight ----Paintwork: * Chassis, bogie, drawbar and drive-on ramps hot-dip galvanized * Axles, springs, air tanks etc. painted black ----Info: * Permissible gross weight technically up to 30,000 kg * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: Immediately available from Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 31.000 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 07/2024, dolžina tovornega prostora: 9.290 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 950 mm, * PT 40.0 Profi ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: Dcjdol Tlhrspfx Apwoi * Air suspension with lifting and lowering system, including RtR valve ----Drawbar: * Drawbar with 50 mm towing eye and height adjustment ----Lighting / Electrics: * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power connector * LED lighting system 12 / 24 V * Removable rear LED beacon * 2 LED reversing lights (activated via reverse gear) ----General equipment: * Manometer - pressure gauge for load weight determination (axles separated into 2 air suspension circuits) * Side underrun protection * Swing-down supports at the rear of the chassis frame * Mechanically adjustable warning sign sets front and rear * VA plastic quarter mudguards with spray protection * HA straight galvanized steel skirts with spray protection * Reflective contour tape on sides and rear * Tool box, galvanized steel sheet, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high ----Low loader platform: * Forepart in front of the turntable platform, approx. 490 mm long with 45° corners * ROBOT-welded anti-slip surface on the steel plate of the turntable platform * Hardwood floor on the running surfaces of the low loader platform ----Load securing (La-Si package comprising): * In front of the front wall support, 1 x 13.4 t UVV lashing point each left & right * 4 lateral holes each in the turntable platform with 2 t lashing capacity each * 1 pair of lashing points (13.4 t) hanging at the rear left & right in front of the rear support * 4 pairs of UVV lashing rings (10 t) on each side, swiveling and lowering, loadable in all directions and recessed in the outer frame * 3 pockets for stanchions per side, with simultaneous 2 t lashing facility ----Widening package: * Hot-dip galvanized mechanical folding outriggers for 3 m overall width (not in the rear taper) * Plank holder for extensions under the chassis on the left, longitudinally ----Excavator arm rest: * Excavator arm rest above HA up to the end support, approx. 2,100 mm long and approx. 190 mm deep * 2 pairs of 6.4 t lashing points each side in the excavator arm rest ----Ramps: * Hydraulic one-piece approach ramps (approx. 3,000 x 720 mm), mechanically adjustable sideways * Outer planks of ramps made from hardwood * Steel structure prepped for 6-section control valve ----Loading height: * Loading edge unladen approx. 950 mm +/- 20 mm ----Tires: * 235/75 R 17.5 tires ----Paintwork: * Chassis, turntable, folding outriggers, mechanical supports, and approach ramps hot-dip galvanized * -- Axles, air tanks, drawbar finished in a shade of black -- ----Information: * Vehicle has a day registration in 07/2024 due to missing tire pressure monitoring system, and has not been loaded/used * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Immediately available from Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 31.000 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 07/2024, dolžina tovornega prostora: 9.290 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 950 mm, * PT 40.0 Profi ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 4 x 11 tonne Gigant axles ----Suspension: * Air suspension with lifting and lowering system and RtR valve ----Drawbar: * Drawbar with 50 mm towing eye and height adjustment ----Lighting / Electrical: * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power connector * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (activated via reverse gear) ----General Attachments: * Manometer (pressure gauge) for load weight determination (axles separated into 2 air suspension circuits) * Side underrun protection * Swing-down supports at the rear of the chassis frame Dcodpfol Tnu Ajx Apwei * Mechanically adjustable warning boards, front and rear * Front axle plastic mudguards with spray protection * Rear axle straight galvanized steel side skirts with spray protection * Reflective contour tape on the sides and rear * Tool box, black powder-coated galvanized steel, approx. 1,000 mm wide, 600 mm deep, 300 mm high ----Low Loader Platform: * Front extension in front of the turntable platform, approx. 490 mm long with 45° corners * ROBOT-WELDED anti-slip coating on the steel plate of the turntable platform * Hardwood flooring on the running areas of the low-bed platform ----Load Securing (La-Si package consists of): * 1 x 13.4 t UVV lashing ring left & right in front of the headboard carrier * 4 fixing holes each side in the turntable platform, each with 2 t lashing capacity * 1 pair of lashing rings (13.4 t), suspended at the rear left & right in front of the rear carrier * 4 pairs of UVV lashing rings (10 t) per side, pivotable and lowerable, loadable in all directions and recessed into the external frame * 3 stake pockets per side, each offering 2 t lashing capability simultaneously ----Widening Package: * Hot-dip galvanized mechanical folding outriggers for 3 m overall width (not in the rear slope) * Beam bracket for widenings under the chassis on the left, longitudinally mounted ----Excavator Arm Rest: * Excavator arm rest above the rear axle up to the end cross member, approx. 2,100 mm long and approx. 190 mm deep * 2 pairs of 6.4 t lashing rings per side in the excavator arm rest ----Ramps: * Hydraulically operated one-piece drive-on ramps (approx. 3,000 x 720 mm), mechanically adjustable sideways * Outer planks of the ramps made from hardwood * Steel construction prepared for 6-way control valve ----Loading Height: * Loading edge unladen approx. 950 mm +/- 20 mm ----Tyres: * Tyres 235/75 R 17.5 ----Coating/Paintwork: * Chassis, turntable, folding outriggers, mechanical supports, and drive-on ramps hot-dip galvanized * --Axles, air tanks, drawbar painted black-- ----Infos: * Vehicle has a daily registration as of 07/2024, due to the missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery Time: * Available immediately from Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 27.300 kg, skupna masa: 36.000 kg, konfiguracija osi: 3 osi, prva registracija: 04/2013, naslednji pregled (TÜV): 08/2026, dolžina tovornega prostora: 11.700 mm, širina tovornega prostora: 3.000 mm, skupna širina: 2.550 mm, skupna višina: 3.700 mm, Oprema: ABS, * Gugalnica z zaboji za shranjevanje * Sledilne krmiljene osi * Hidravlične nakladalne rampe * Razširljiva nizkopodna ploščad ----* Dimenzija pnevmatik: 235/75R17,5 * Tehnična skupna masa: 42.000 kg * Lastna teža: 8.700 kg Dcsdpfx Apeza Rliewei * Skupna dolžina: 13.150 mm * SP veljavnost do: 02/2027 ----Številka vozila: 12148 ----Možne napake in vmesna prodaja pridržane ----Oglasi in različni napisi so bili digitalno odstranjeni. -----Z veseljem vam pomagamo pri vseh formalnostih, ki nastanejo ob nakupu vozila – sporočite nam vaše želje in predloge ter za vse ostalo bomo poskrbeli mi. Med drugim vam lahko za doplačilo ponudimo naslednje storitve: ----Odkup vašega starega vozila TÜV/SP tehnični pregled Popolna izvozna obdelava Posredovanje financiranja Urejanje izvoznih tablic Prevoz vozil Registracija vozil Reševanje in transport vozil ----VAŠ VTS TEAM

Stanje: novo, največja dovoljena obremenitev: 23.940 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profi 30.0 ----Brakes: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t Gigant axles ----Suspension: * Parabolic springs with mechanical rear axle compensation ----Drawbar: * Drawbar with 50 mm towing eye and height adjustment via drawbar spring & turnbuckle ----Lighting / Electrics: * TPMS Tire Pressure Monitoring System * Multi-voltage system * LED tail lights 12 / 24 V * Rear removable warning beacon * 15-pin power connector ----General Equipment: * Side underrun protection * Rear swing-down support legs on chassis frame * Mechanically adjustable warning panel kits front and rear * VA closed plastic mudguards in front and straight galvanized steel skirts at the rear, each with spray protection * Tool box made of galvanized steel sheet - black powder-coated - approx. 650 x 300 x 600 mm * Folding lid (hot-dip galvanized) for the toolbox in the turntable platform * Four stake pockets per side (stakes not included), also with lashing function ----Load Securing (La-Si package consisting of): * 2 lashing eyes (6.4 t) front left & right on the main frame of the turntable platform * 6 pairs of UVV folding and retractable lashing rings, loadable in all directions and countersunk into the outer frame * 13.4 t at corners, 10 t otherwise ----Widening: Dcodjl Th Nnopfx Apwsi * 6 pairs of manual folding outrigger arms for 3 m overall width (not on the sloped rear section) * Widening boards stowed in the center of the loading area ----Ramps: * Hot-dip galvanized one-piece hydraulic loading ramps (approx. 3,000 x 720 mm), mechanically adjustable sideways * 4-way hydraulic control unit pre-installed for optional hydraulic side shift of ramps ----Loading Area: * Over turntable: approx. 1,960 x 2,520 mm & unladen height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm & unladen height approx. 910 mm (incl. 860 mm entry incline) ----Tyres: * 235/75 R 17.5 twin tyres ----Unladen weight: * Approx. 5,980 kg unladen weight ----Finish: * Chassis, turntable, drawbar and loading ramps hot-dip galvanized * Axles, springs, air tanks etc. painted black ----Information: * Permissible total weight of 30,000 kg technically possible * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available ex stock Egestorf

Stanje: rabljeno, skupna masa: 47.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2004, naslednji pregled (TÜV): 08/2026, * Müller Mitteltal TS3 nizkopodni polpriklopnik * Prva registracija: 11/2004 * 3 osi * Zračno vzmetenje * Gigant osi Dcsdpfxjw Tgkbo Apwei * Hidravlične dolge rampe, pomične in zložljive * Razširitve iz 2,50 m na 3,0 m širina nakladalnega prostora * Nakladalna dolžina: 8,50 m pri nakladalni višini 0,85 m * Nakladalna dolžina na vratu: 3,40 m pri nakladalni višini 1,50 m * Podpore * Neto teža: 10.260 kg * Tehnično dovoljena skupna masa: 47.000 kg * TÜV veljaven do: 08/2026 * Tehnični pregled do: 02/2026

Stanje: novo, največja dovoljena obremenitev: 23.210 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, * T 3: * ABS zavorni sistem * Sistemska oprema za sprostitev vzmetnih cilindrov v sili * Bobnaste zavore * 3 x 11 t. BPW Eco osi * Parabolaste vzmeti * Mehanski izravnalnik osi zadaj * Stranska zaščita proti naletu * Zadnje vrtljive oporne noge na šasiji vozila * Mehansko nastavljivi opozorilni tablini paketi spredaj in zadaj Dcsdpfx Aoq Dyv Ispwji * Spredaj zaprti plastični blatniki in zadaj ravne pocinkane jeklene zaščite proti pršenju, obe s ščitniki proti brizganju * Konturirani odsevni trakovi ob straneh in zadaj * Zložljiv pokrov orodjarne (vroče pocinkan) na rotacijski ploščadi * Orodjarna iz pocinkanega jekla približno 650 x 300 x 600 mm – črno prašno barvana – ob strani pod šasijo * 15-pinski električni priključek * LED osvetlitev 12 / 24 V * LED rotacijska luč (odstranljiva) zadaj * Vlečna škarja z vlečnim ušesom 40 mm in nastavitvijo višine preko vlečne vzmeti in napenjalnega vijačnika * Na vsaki strani po 4 žepi za pilote (brez pilotov) z istočasno možnostjo pritrjevanja * Paket za varno nalaganje (La-Si): 2 pritrdilni obroči (6,4 t) spredaj levo in desno na glavnem okviru rotacijske ploščadi * 5 parov UVV vrtljivih in spuščajočih se pritrdilnih obročkov * Nosilnost v vse smeri; v vogalih zunanjega okvirja do 13,4 t, sicer 10 t * 6 parov mehanskih zložljivih podaljškov za skupno širino 3 m (ne vključuje zadnje zaokrožitve) * Razširitveni podesti shranjeni v predalu pod tovorno površino * Odlagalna površina za roko bagra nad zadnjo osjo do končnega nosilca, dolga cca. 2100 mm (2 para stranskih pritrdilnih obročkov 6,4 t v odlagalni površini) * Hidravlične zložljive rampe (pribl. 4650 x 720 mm) z hidravlično nastavljivim vrhnjim delom in varnostnimi ventili, hidravlični stranski premik ramp * Hidravlični razdelilnik v prikolici (za hidravlično črpalko v tovornjaku z zmogljivostjo nad 40 l/min, največ do 140 l/min), dvocevna hidravlika * Nakladalna površina nad vrtljivim ležajem: pribl. 1960 x 2520 mm * Zadnja nakladalna površina: pribl. 6500 x 2520 mm (vklj. 860 mm naletne rampe) * Nakladalna višina obremenjeno pribl. 860 mm +/- 30 mm prilagoditev * Šasija, rotacijska ploščad, zložljivi podaljški, padajoče oporne noge zadaj in rampe toplotno pocinkane * Osi, vzmeti, vlečna škarja, zračni rezervoar itd. lakirani v črnem odtenku * Novo vozilo z garancijo proizvajalca * Pridržujemo si pravico do sprememb in vmesne prodaje * Na voljo takoj iz Egestorfa

Stanje: novo, največja dovoljena obremenitev: 23.210 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, * T 3: * ABS zavorni sistem * Naprava za nujno sproščanje za vzmetne valje Dcodpfx Apotplwfswei * Bobnaste zavore * 3 x 11 t BPW Eco osi * Parabolične vzmeti * Mehanski izravnalnik osi zadaj * Stranska zaščita proti naletu * Zadaj na okvirju podvozja vrtljive podporne noge * Mehansko nastavljivi opozorilni tabli spredaj in zadaj * Spredaj zaprti plastični blatniki, zadaj ravne pocinkane jeklene zaščitne letve, vsaka z zaščito proti brizganju * Reflektirajoči konturni trakovi ob straneh in zadaj * Pokrov (vroče cinkan) za orodjarno na vrtljivi ploščadi * Orodjarna iz pocinkanega jekla približno 650 x 300 x 600 mm – prašno lakirana v črno – stransko pod podvozjem * 15-polni električni vtikač * LED osvetlitev 12 / 24 V * Snemljiva LED rotacijska luč zadaj * Vlečna skoba z vlečno čeljustjo 40 mm in nastavitvijo višine preko vzmeti in natezne zaponke * Na vsaki strani po 4 žepe za kole (kole niso priložene) z možnostjo pritrjevanja tovora * Paket za varovanje tovora tipa La-Si, ki vsebuje: 2 pritrditveni ušesi (6,4 t) spredaj levo in desno na glavnem okviru vrtljive ploščadi * 5 parov UVV priveznih obročev, zložljivih in nagibnih * Nosilnost v vseh smereh, v zunanjih okvirnih kotih vgrajeni 13,4 t, sicer 10 t * 6 parov mehanskih zložljivih nosilcev za širino do 3 m (ne na zadnjem poševnem delu) * Razširitvene deske shranjene v posebnem predalu pod nakladalno površino * Polica za bagersko roko nad zadnjo osjo do končnega nosilca, dolga cca. 2.100 mm (2 para 6,4 t pritrdilnih obročev ob strani police za bagersko roko) * Hidravlične zložljive rampe (cca. 4.650 x 720 mm) z hidr. izvlečnim koncem, ventili za ohranjanje bremena, hidr. stransko pomikanje ramp * Hidr. razdelilnik pretoka na prikolici (pri hidravlični črpalki na tovornjaku nad 40 l/min do največ 140 l/min), dvovodna hidravlika * Nakladalna površina nad vrtljivim ležajem: cca. 1.960 x 2.520 mm * Zadnja nakladalna površina: cca. 6.500 x 2.520 mm (vključno z 860 mm naklonskim delom) * Višina nalaganja obremenjeno cca. 860 mm +/- 30 mm kompenzacijskega agregata * Podvozje, vrtljiv okvir, zložljivi nosilci, zadnje podporne noge in nakladalne rampe vroče cinkani * Osi, vzmeti, vlečna skoba, zračni rezervoarji itd. barvano v črno * Novo vozilo z garancijo proizvajalca * Pridržujemo si pravico do napak in vmesne prodaje * Takoj dobavljivo iz Egestorfa

Stanje: rabljeno, lastna masa: 8.850 kg, največja dovoljena obremenitev: 31.150 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 08/2019, vzmetenje: jeklo, velikost pnevmatike: 235 / 75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235 / 75 R 17,5, velikost zadnje pnevmatike: 235 / 75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, Skupna dolžina tovorne površine pribl. 9.500 mm, dolžina tovorne površine nizkega ležišča pribl. 7.360 mm, višina nakladanja pribl. 910 mm, 14 parov pritrdilnih obročev, vozilo se prodaja po naročilu stranke. Pridržujemo si pravico do tiskarskih napak, sprememb in napak, slike so vzorčne. Več podatkov na zahtevo! Dodpfsziyinex Apwoci

Stanje: rabljeno, največja dovoljena obremenitev: 14.300 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, prva registracija: 02/2020, naslednji pregled (TÜV): 02/2027, dolžina tovornega prostora: 9.800 mm, širina tovornega prostora: 2.520 mm, Oprema: ABS, * ABS * Zadnje podpore Dedpfxey T Dh Ss Apwjci * BPW ECO-Plus osi * Oranžna opozorilna luč * Aluminijasta platišča * Duomatik zračni priključek ----Nadgradnja: Pocinčan nizkopodestni priklopnik (2500+7300 mm)/Višina nakladanja cca 900 mm, zadaj znižan/Naklonska višina cca 770 mm, jeklen/lesen pod in protidrsna prevleka, razširljiv na 3 m, hidravlične nakladalne rampe (zložljive za nizek nakladalni kot) s protidrsno prevleko, tudi hidravlično bočno pomične, pričvrstitveni obroči Prodaja le pravnim osebam. PRI IZVOZU JE TREBA PLAČATI SAMO NETO CENO!!!! VSE INFORMACIJE SO BREZ JAMSTVA, VKLJUČNO Z OPREMO IN DODATKI. Osnova vseh prodajnih pogodb, računov, predračunov, naročil in prodajnih pogovorov so naši splošni pogoji (glejte impressum).

Stanje: rabljeno, največja dovoljena obremenitev: 29.750 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 03/2010, naslednji pregled (TÜV): 05/2026, Mera-B 11.750 mm Lastna teža 10.250 kg Dedpoxpmmmjfx Apwjci Obremenitev osi 2 x 10.000 kg Nakladalna dolžina nad vrtečo ploščo 2.400 mm vklj. 350 mm poševnine Nakladalna dolžina 7.700 mm vklj. 900 mm poševnine Višina nalaganja 880 mm Širina 2.550 mm, razširljivo na 3.000 mm Utornica za odlaganje izkopalnega kraka (DxŠxV cca 2.500 x 740 x 180 mm) SAF osi z zračno vzmetenjem 2-delne hidravlične rampe, 2.100 mm + 2.000 mm dolge, 650 mm široke vklj. Rampe hidravlično nastavljive Hidravlična podpora zadaj Izsek za kolo za drugo osjo Izsek za sprednje kolo, zgoraj dolžina cca 2.000 mm x 1.100 mm, spodaj globina cca 350 mm Izseki za kolesa med 3. in 4. osjo Izsek za zadnje kolo, zgoraj dolžina cca 1.300 mm x 550 mm, spodaj globina cca 220 mm

Stanje: rabljeno, lastna masa: 11.000 kg, največja dovoljena obremenitev: 39.000 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/2015, naslednji pregled (TÜV): 04/2027, dolžina tovornega prostora: 9.250 mm, širina tovornega prostora: 2.720 mm, višina nakladalnega prostora: 950 mm, vzmetenje: zrak, velikost pnevmatike: 235/75R17.5, barva: modra, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Lokacija vozila: Bovenden, 5-osni, suknjič, zračno vzmetenje, zadnja os krmiljena, ABS (protiblokirni sistem), privezne točke, dvodelne nakladalne rampe, hidravlične rampe, zadnje podpore, stranska aluminijasta zaščita, dvojne gume. Djdpfey U N Nwox Apwjci Nadgradnja: 5-osna nizkopodna prikolica s hidravličnima dvodelnima nakladalnima rampama, 5x 10t Gigant osi, bobnaste zavore, zadnja os krmiljena! Na prvih treh oseh so novo nameščene zavorne obloge! PODATKI O DODATNI OPREMI BREZ GARANCIJE, spremembe, vmesna prodaja in napake so pridržane!

Stanje: novo, največja dovoljena obremenitev: 10.800 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: ----Brakes: * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with equalizing device ----Drawbar / Flange Hitch Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm to a total of 2,250 mm ----Electrics / Lighting: * Tire pressure monitoring system with display option in the truck via EBS signal – no installation required on the truck side * 15-pin power connector * LED lighting system 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics ----General Fittings: * Landing gear at the front * External folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, fitted front right outside on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Bed: * 50 mm softwood floor * Provisions in front of the bulkhead for retrofitting container locks * Bolt-on 400 mm bulkhead made of smooth sheet * Removable rear stanchions, bolted * Drop sides with spring assist ----Load securing: * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Option to install 3 t retractable lashing rings every 600 mm * 1 x 6.3 t lashing point in each front and rear corner * Various holes in the headboard and rear crossmember for 1.2 t lashing options * Profifix lashing rail centrally positioned along the longitudinal axis for securing up to LC 3000 daN ----Ramps: * One-piece hydraulic mesh drive-on ramps, approx. 2,750 x 600 mm (collapsible to 20 mm) * Hydraulic flow divider in the trailer (for hydraulic pump output on the truck of over 40 l/min up to max. 140 l/min) ----Painting: * Chassis, drawbar, bulkhead, mechanical drop supports and drive-on ramps hot-dip galvanized * Axles, springs, air reservoirs, landing gear front, and flange hitch eye painted in black shade * Drop sides painted in RAL 9010 pure white * Painting of the side walls in a RAL color of your choice available at extra charge ----Information: * New vehicle with manufacturer’s warranty * Subject to errors and prior sale Djdpferwc R Rsx Apweci ----Delivery time: * Available immediately ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting/lowering system and RtR valve * Smard board for payload weighing * Warning sign kits, front and rear * Reflective contour tape on the sides and rear * Removable rotating beacon (rear) * LED lighting * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated steel sheet and basket-type spare wheel holder, mounted right side * Front: closed single plastic mudguard * Rear: straight steel mudguards, each with spray suppression * Side underrun protection * Bogie platform extension by 520 mm with 45° corners, 3 integrated lockable storage compartments with lids * Chassis made of high-strength fine-grained steel * 50 mm softwood floor over bogie platform, 60 mm softwood on low-bed platform * Outer rails on ramps made of hardwood * 4 stake pockets per side (no stakes included); 2 t lashing possible at each * Load securing package: 2 lashing eyes (6.4 t) front left/right on main frame of bogie platform * 2 pairs of lashing rings (13.4 t) on outer frame front/rear per side; 4 pairs of lashing rings (10 t), swing-out and lowerable per side (front/rear) * All lashing points loadable in all directions and recessed into outer frame * 2 pairs of lashing rings (6.4 t) in excavator arm rest area * 8 pairs of galvanized folding outriggers for 3 m overall width (not at rear slope) * Extension planks stored left side in a storage box * Excavator arm rest above rear axle to end of rear slope, approx. 2,100 x 740 x 190 mm * Rear mechanical fall supports * Hydraulic folding ramps with hydraulically adjustable ramp tip, approx. 4,650 x 720 mm, incl. hydraulic lateral ramp adjustment & load-holding valve * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Loading height loaded approx. 890 mm, +/-20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, bogie, ramps, outriggers and mechanical fall supports hot-dip galvanized * Axles, drawbar, air reservoir and turntable in black finish * Tires: 235/75 R 17.5 * New vehicle, no initial registration, manufacturer’s warranty Dedpjl Tik Nefx Apwjci * Subject to errors and prior sale * Immediately available ex Egestorf, A7

Stanje: novo, največja dovoljena obremenitev: 13.600 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2026, * KA-TA-RT 18.0: ----Brake: * EBS (Electronic Braking System) * Emergency release for spring brake cylinders * Drum brakes ----Suspension: * Air suspension with lifting and lowering device, including Ride-Through-Release (RtR) valve and manual lowering function for loading ----Drawbar / Flanged Drawbar Eye: * Drawbar with positive-locking height adjustment * 50 mm flanged drawbar eye ----Electrics / Lighting: * 15-pin 24 V connector * LED tail lights 12 / 24 V fitted in underrun protection ----General Attachments: * Support winch at front * Fold-away rear support legs on the outside * Plastic toolbox approx. 750 x 350 x 300 mm, mounted on right side * Plastic quarter mudguards ----Tipping Body: * Steel pallet – 3-way tipper body made of high-tensile fine grain steel with high M-Strong side panels and reinforced 180 bar tipping cylinder * Fixed front wall made of smooth sheet steel * Hardwood strip for excavator bucket screwed onto front wall * Continuous side panels – fold-down without center pillar, with sideboard spring-assist lifters and swinging function via manual central locking * Bolt-on rear stanchions * Combination steel swing doors at rear, 2-leaf, asymmetrically split, able to swing open 270° and lockable (not foldable), including additional swinging frame for automatic rear door opening when tipping; locking by galvanized rotating bar lock and central locking, deactivation function for automatic rear door opening when tipping backwards with opened swing doors * 4 mm steel floor plate * Two-step access on the left front * Rear ramp track for loading ramps ----Load Securing: * One 7 t lashing ring in each corner * Four 3 t lashing eyes recessed in the outer frame on each side ----Loading Ramps: * Recessed ramp compartment at rear of chassis * 1 pair aluminium loading ramps (10 t/pair), approx. 3,570 x 410 mm, suitable for rubber-tired and tracked vehicles ----Paintwork: * Chassis, drawbar, rear stanchions, front wall, tipping platform, underrun protection, and rear supports hot-dip galvanized * Sideboards painted in any desired RAL colour (excluding special or metallic paints), can be changed up to approx. 6 weeks before completion * Axles, air tanks, flanged drawbar eye, and front support winch painted in black ----Info: * --Load securing certificate according to EN 12642 XL? Dsdovin Ucepfx Apwsci * Errors and intermediate sale reserved ----Delivery Time: * Available from approx. CW 45 / 2026