Priklopnik z delovno ploščadjo

MÜLLER-MITTELTAL 3-Achs Plateau, luftgefedert, hydr. Rampen

Stanje: novo, največja dovoljena obremenitev: 23.500 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.380 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, PT 30 Profile: ----Braking System: * EBS (electronic braking system) * Emergency release mechanism for spring-actuated cylinders * Drum brakes ----Axle: * 3 x 11 t Gigant axles ----Suspension: * Air suspension with lifting and lowering system, including RtR valve ----Drawbar: * Drawbar, 1,200 mm long, with 40 mm towing eye and height adjustment via traction spring & turnbuckle ----Electrical / Lighting: * Smart-Board information system mounted on the trailer (for axle load indication – separate front and rear display) * Tire pressure monitoring with display capability in the truck via EBS signal, no truck-side installation required * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear ----General Attachments: * Side underrun protection * Swing-out supports at the rear of the chassis frame * Mechanically adjustable warning board sets front and rear * Front axle plastic quarter mudguards with spray protection * Rear axle straight galvanized steel mud skirts with spray protection * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm, black powder-coated, mounted right side * Compartment in the bogie for accessories, with folding lid and 2 fixed container locks (directly behind the bogie platform) * 2 galvanized steps on the bogie, left and right Podsxptn Rjpfx Ahtogn ----Low Loader Platform: * Robot-welded non-slip overlay on the steel plate of the bogie platform (protruding weld seams) ----Load Securing (La-Si package consisting of): * 2 lashing eyes (13.4 t) front left & right on front bulkhead carrier * 1 pair of UVV lashing rings at front & rear (13.4 t) and 3 pairs of UVV lashing rings on each side (10 t), pivotable and lowerable, loadable in all directions, recessed in outer frame * 3 stake pockets on each side, each with 2 t lashing capacity * Profifix lashing rail in longitudinal axis, centered in flat area, for lashing up to LC 3000 daN ----Widening: * 6 pairs of mechanical folding outriggers for 3 m overall width (not in the rear taper) * Widening planks stored in the centre of the loading platform ----Ramps: * Hydraulic one-piece drive-on ramps, approx. 3,000 x 720 mm * Mechanically adjustable laterally * 4-way control block for future retrofit of hydraulic ramp lateral adjustment ----Excavator Arm Rest: * Excavator arm rest above rear axle, extending to the rear end crossmember (total length approx. 2,100 mm) * 2 pairs of lashing eyes LC 6400 daN in the excavator arm rest, located laterally in the main longitudinal frame ----Loading Height: * Loaded approx. 910 mm +/- 20 mm (air suspension) ----Paintwork: * Chassis, bogie, folding outriggers, drop-down supports and ramps hot-dip galvanized * Axles, slewing ring, air tanks, and drawbar painted in black ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex Egestorf

Stanje: rabljeno, lastna masa: 10.900 kg, največja dovoljena obremenitev: 43.600 kg, skupna masa: 54.500 kg, konfiguracija osi: 3 osi, prva registracija: 04/2025, dolžina tovornega prostora: 8.700 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 855 mm, velikost pnevmatike: 245/70 r17.5, barva: siv, Leto izdelave: 2025, obratovalna teža: 10.900 kg, Oprema: ABS, Gooseneck, rigid, center tube design: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Steel floor with anti-slip coating - Including perforated rail for aluminum approach ramps - 2" king pin - Manually operated BPW landing legs - 550 mm long, 8° chamfer at end of gooseneck - Front wall including park position for rear wall, 400 mm high - Spare wheel holder mounted vertically on the front side of the gooseneck - 3 pairs of recessed lashing rings (LC 5,000 daN) in the loading area of the gooseneck - Aluminum side boards, 400 mm high, comprising 2x side boards each 3,150 mm long, and rear board with stanchions (galvanized) - Rectangular aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, center - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, left - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, right Loading platform, single-extendable: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) Pgjdpfx Ahji Ai E Retjn - Fixed section at front 700 mm - Steel plate floor with anti-slip coating - Chamfered transition between fixed part and deck for bridging rails and wheel recesses - Excavator trough including elongated holes for load securing (LC 1,500 daN), length approx. 3,850 mm - Prepared for hydraulic ramps (electrical supply) - Rails to widen up to 3,000 mm - 8° chamfered vehicle rear, 550 mm long - Slide system for easy mounting/dismounting of ramps - Continuous mud flap at the rear - 1 pair of lashing points LC 10,000 daN centrally on the loading area behind the gooseneck - 7 pairs of lashing points LC 10,000 daN in the outer frame of the loading platform - 6 pairs of stanchion pockets 100 x 50 mm in the outer frame of the loading platform - 1 pair of lashing points LC 10,000 daN centrally in the rear section of the loading platform - 1 pair of stanchion pocket rails approx. center of the loading area - 1 pair of stanchion pocket rails on the fixed part - 1 pair of stanchion pocket rails behind the last axle Ramps: - Hydraulic double-folding ramps, 2,750+1,500x800 mm - Larch wood surface - Operated by remote control (wired and wireless) - Quick-change ramp (dismantling system) Chassis: - Axle brand: BPW ECO Max - 2 ride heights - 4 axles @ 10 t (technically 12 t) - Twin tires 245/70 R17.5 - 2 x rigid axles and 2 x friction-steered axles - Reverse steering lock for friction-steered axles via reverse gear - Brake system by Knorr (according to EU standards with EBS-E) - Knorr TIM G2 (Trailer Information Module) - RSS (Roll Stability Support) stability control - Load-dependent lift axle on the first axle incl. starting aid (forced lowering of lift axle via TIM possible) Accessories: - 4 wheel chocks with holder - 2 pairs of warning panels 423 mm x 423 mm, with 2 position lights and socket for rotating beacon, steplessly adjustable up to 3,950 mm - Securing points on gooseneck and on loading platform (alternatively on ramp, if available) included - Plug-in bulkhead at the end of the excavator trough - Electrohydraulic unit for ramp operation - Ramp control by wireless remote - Hydraulic rear support legs for stabilization during loading - 1 pair of additional reversing lights at the rear, activated when reversing - Larch wood widening planks (option)

Stanje: novo, največja dovoljena obremenitev: 36.020 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 435/50 R 19.5, barva: siv, Oprema: ABS, Loading platform: - Loading platform in extendable design with pneumatically operated locking mechanism - 2 pairs of lashing rings (LC 5,000 daN) - 1 pair of lashing rings (LC 10,000 daN) - 6 pairs of fold-out lashing rings (LC 5,000 daN) - 2 pairs of fold-out lashing rings (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for attaching tension belts Axles and tires: - BPW axles, air-suspended, with disc brakes (377 mm), equipped with lifting/lowering function - Self-steering axles with electromagnetically controlled reverse lock, activated via reverse gear or manually - Axle tools - Tires: 435/50 R 19.5 Brake system: - Brake system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - Premium, durable corrosion protection for the standard shot-blasted welded frame by means of two-component (2K) zinc dust primer - High-quality two-component (2K) top coat in solid Novagrau - Rear end metallized and painted in RAL 9010 (pure white) - Metallic paint not available Landing gear: - JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Steel construction: - Steel structure made of high-strength fine-grained steels. - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDICK (ASS3) lighting - ASPÖCK-UNIBOX on the front connection console with 24N, 24S & 15-pin sockets - Connections according to ISO standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Accessories included: - Yellow-red air couplings at the galvanized front connection strip Pedpji Dwlwsfx Ahtegn - 2 wheel chocks with holder - 2" kingpin - A galvanized steel front wall approx. 1,600 mm high - Yellow reflective tape as per EU regulations, on the sides, on the extension and at the rear of the trailer - European reflective signs (red-yellow) at the rear of the trailer - Loading area with approx. 38 mm thick hardwood floor - 10 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame of the platform - 1 spare wheel holder beneath the loading area on the right in the direction of travel - User manual and documentation on USB stick - One mudflap at the rear of the trailer - Bracket for a revolving beacon at the rear of the trailer - On the gooseneck and on the rear panel, left and right, each a bracket for warning boards including socket - One INOX toolbox transversely mounted beneath the platform (1,000x400x2,500mm) - 6 pairs of WADER container locks in the platform for 1x 20ft container, 2x 20ft containers or 1x 40ft container; an additional locking point is provided in the extension for a 45ft container - 3 sets of crosswise post pocket bars mounted in the platform for 100 x 50 mm plug-in posts - 60 km/h speed sticker on the rear - 2 reversing spotlights mounted on the rear panel - Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light - Mounting bracket for rotating beacon on the warning sign - HRM metallization (High Resistance Metallisation) of the outer frame - Entire steel structure shot-blasted, the defined visible surfaces then hot-finished with ZINACOR 850 metallisation (zinc 85% - aluminum 15%)

Stanje: novo, lastna masa: 10.600 kg, največja dovoljena obremenitev: 39.400 kg, skupna masa: 50.960 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5, barva: siv, obratovalna teža: 10.600 kg, Oprema: ABS, Gooseneck: - Gooseneck with 30 mm hardwood flooring - Gooseneck at rear in straight version - 3 pairs of lashing rings (LC 5,000 daN) Extendable load floor: - Load floor in extendable configuration - 5 pairs of lashing rings foldable outward - 3 pairs of lashing rings foldable outward - 1 pair of lashing rings laying at the front end of the load floor - Cut-outs in the outer frame of the load floor for attaching tension straps - Approx. 48 mm hardwood flooring, checker plate covering above the axles Landing legs: - JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tyres: - BPW axles, two rigid axles, two self-steering axles - Air suspension with drum brakes, with lift/lower function - The self-steering axles are equipped with an electromagnetically operated reverse lock, which can be activated via reverse gear or manually - Axle tools - Tyres 205/65 R17.5 Brake system: - Brake system compliant with EU regulations with EBS-E (4S3M) Steel structure: - Steel construction made from high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system in accordance with EU regulations, lighting 24 Volt, ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets - Connections according to ISO: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Paintwork: - High-quality and durable corrosion protection on the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer - High-quality single-colour 2-component (2K) top coat in Novagrau - Rear section metallised and painted in RAL 9010 (Pure White) Included accessories: - One spare wheel with holder in front of the bulkhead - 2" king pin - Galvanised steel front wall approx. 400 mm high - Yellow-red air couplings on the galvanised connection bar at the front - 4 wheel chocks with holder at the front wall - Galvanised folding supports under the load floor slope Pjdpfx Aet Ag Uwshtegn - Holder for a warning beacon at the rear of the trailer - Galvanised extensions, extendable by approx. 230 mm per side - White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear - On the gooseneck and rear panel, left and right, one bracket each for warning panels including socket - European reflective markings (red-yellow) at the rear of the trailer - TPMS tyre pressure monitoring system according to ECE R 141 - On the gooseneck, plug-in ALU side walls and rear wall, approx. 2,440 x 400 mm - The rear, galvanised plug-in side stanchions are removable, length of the body approx. 2,560 mm - 7 pairs of WADER container pockets - 1x 20ft container on the load floor; 1x 40ft container on the load floor; 1x 40ft container above the gooseneck; 2x 20ft container - 7 pairs of stanchion sockets for plug-in stanchions 100 x 50 mm in the outer frame of the load floor - Lift axle on the front axle with control via TEBS E, depending on the current axle load and load condition - Sliding plug-in rail for ALU loading ramps at the rear of the vehicle - Anti-slip sand finish painted on the checker plates on the gooseneck and load floor - Four warning boards extendable by approx. 400 mm, approx. 423 x 423 mm, each with a position lamp - Holder for warning beacon on the warning boards - 80 km/h speed stickers at the rear and on both sides - Axle load gauge for determination of axle loads inclu

Stanje: novo, lastna masa: 7.900 kg, največja dovoljena obremenitev: 41.600 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, obratovalna teža: 7.900 kg, Oprema: ABS, Swan Neck: - Swan neck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood decking Loading Area: - Loading area with rear chamfer of approx. 1,000 mm x 8° - Recess in the chamfer and encroaching into the loading area for receiving the excavator bucket stick approx. 2,900 x 750 x 210/290 mm - Cut-outs in the external frame of the loading area for attaching tension straps - Hardwood decking approx. 48 mm thick, over the axles with tread plate covering Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox, 24t lifting capacity (50t test load) Axles and Tyres: - BPW axles and suspension, 2 axles rigid, 1 axle self-steering t- Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with raising and lowering valve - TPMS tyre pressure monitoring system compliant with ECE R 141 - Tyres 235/75 R 17.5 Paintwork: - Complete steel structure blasted automatically by wheel blast machine after welding - Second blasting with corundum for optimal adherence of the coating system - Final coating: two layers of 2K top coat, solid colour in RAL MB 7350 Novagrau - Rims painted silver - Rear section metallised and coated in RAL 9010 (Pure White) - Cavity sealing with special wax Electrical System: - Electrical system according to EU standards, 24 volt ASPÖCK-NORDIK (ASS3) lighting - ASPÖCK-UNIBOX at front connection rail with sockets 2x 7-pin & 1x 15-pin Included Accessories: - Multiple lashing positions - 2" king pin - One galvanised steel front wall approx. 400 mm high - Yellow-red air couplings on galvanized front connection rail - 4 wheel chocks with holders mounted on the front wall - Receiver at rear of swan neck for ALU loading ramps - Galvanised folding supports beneath rear chamfer of loading area - Bracket for beacon at rear of trailer - Galvanised extendable outriggers, extendable by approx. 230 mm per side Psdpfx Ajunrapohtjgn - White reflector tape to EU spec at sides and rear, red at rear - Brackets for warning signs on left and right of swan neck and rear panel, including socket - ALU side boards and rear board on swan neck, removable, approx. 2,440 x 400 mm - Rear galvanised stake pockets are removable - 2 pairs WADER container pockets in loading area for 20ft container - 6 pairs stake pockets for removable stakes 100 x 50 mm in the outer frame - Adjustable hanging rail for ALU access ramps at the rear of the vehicle - Square climbing strips 20 x 20 mm every 200 mm on the outer frame of the loading area chamfer - Sand-finish anti-slip coating painted onto the tread plate on swan neck and loading area - Four warning boards extendable by approx. 400 mm, approx. 423 x 423 mm with position light - Bracket for beacon fitted to warning boards - 80 km/h speed sticker rear and on both sides - European reflective signs (Red-Yellow) at the rear of trailer - Manual and operating instructions on USB stick - HRM metallisation (High Resistance Metallisation) of the external frame - Complete steel structure shot-blasted, then specified visible surfaces metallised with ZINACOR 850 (Zinc 85% - Alu 15%) hot-finished