Müller-Mitteltal Ra Prikolice nakup rabljenega (252)

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic brake system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting/lowering system and RtR valve * Smard-Board for load weight determination * Warning sign packages at the front & rear * Reflective contour tape on the sides and rear * Removable rear rotating beacon * LED lighting * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated sheet steel and spare wheel holder in basket design on right side * Front: closed single plastic mudguards * Rear: straight steel mud flaps with spray suppression * Side underrun protection * Turntable platform extended by 520 mm at the front, with 45° corners and 3 recessed, lockable storage compartments with lids * Chassis made of high-strength fine-grain steel * Decking over turntable platform made of 50 mm, and in low-bed platform of 60 mm coniferous timber * Outer planks of ramps made of hardwood * 4 stake pockets on each side (no stakes provided) with simultaneous 2 t lashing capability * Load securing package includes: 2 lashing eyes, 6.4 t, at the front left and right on the main frame of the turntable platform * On each side front and rear: 2 pairs of 13.4 t lashing rings on the outer frame and on each side 4 pairs of swiveling and lowerable 10 t lashing rings * Loadable in all directions, recessed into the outer frame * 2 pairs of 6.4 t lashing rings on the side in excavator arm recess * 8 pairs of galvanized folding outriggers for 3 m total width (not at the rear slope) * Widening planks stored in a side compartment on the left * Excavator arm recess over the rear axle to end of rear slope approx. 2,100 x 740 x 190 mm * Mechanical drop supports at rear * Hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm including hydraulic sideways ramp adjustment & load-holding valve * Loading deck over turntable: approx. 2,990 x 2,520 mm * Rear loading deck: approx. 6,780 x 2,520 mm Nodpol Tphrsfx Af Aswc * Load height loaded approx. 890 mm, +/- 20 mm (including 860 mm rear slope) * Flow divider installed * Chassis, turntable, loading ramps, folding outriggers, and mechanical drop supports hot-dip galvanized * Axles, drawbar, air reservoirs, and turntable painted in black * Tires: 235/75 R 17.5 * New vehicle, not previously registered, with manufacturer’s warranty * Errors and prior sale reserved * Available from CW 07/2026

Stanje: novo, največja dovoljena obremenitev: 14.550 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2024, * ETÜ-TA-R 19.0: * Wabco EBS-E (electronic braking system) * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 11 t Gigant axles * Air suspension, drawbar with 50 mm flange eye and height-adjustable drawbar * Jost landing gear at the front * External folding supports at the rear * Toolbox made of galvanized sheet steel approx. 650 x 350 x 320 mm mounted laterally right (black powder-coated) * Side underrun protection * Plastic quarter-mudguards * 15-pin electrical connector Nodpfx Afspk D D He Aswc * LED tail lights * Reinforcement package for drill rig transport on chassis – load height +20 mm * 50 mm softwood floor, clamped design * Preparation for subsequent fitting of container locks in front of the bulkhead * Bolt-on front wall made of smooth steel sheet * Trapezoidal-profiled side walls made of steel sheet, foldable with drop-side spring assists * Steel rear wall, retractable between the ramps – storage bracket inside front wall when not in use * Bolted rear stanchions * Perforated outer frame, approx. 45° bent, with 2 t lashing force every 480 mm * Option to install 3 t folding lashing rings every 600 mm * In each front and rear corner, 1 x 10 t lashing ring, front and end beams with multiple holes for 1.2 t lashing points * One-piece mechanical grated ramps with spring system for single-person operation, approx. 2,750 x 620 mm (collapsible to 20 mm) * Rear approach angle approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, rear folding supports, and ramps hot-dip galvanized * Axles, springs, air reservoirs, and landing gear painted black * Wheelbase: 1,310 mm * Tires: 235/75R17.5 * Drop-side panels painted RAL 9010 pure white * Side panels can be painted in any RAL color at extra cost * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available immediately from Egestorf

Stanje: novo, največja dovoljena obremenitev: 14.200 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2023, * ETÜ-TA-R 19.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 11 t Gigant axles * Air suspension * Drawbar with 50 mm flanged towing eye and height adjustment of 110 mm via offset plate * Jost support winch at the front * External folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, right side * Side underrun protection * Plastic quarter mudguards * 15-pin power connector * LED lights * Reinforcement package for drilling rig transport on the chassis * 50 mm softwood floor with clamped design * Mounting provision in front of the bulkhead for retrofitting container locks * Bolted smooth steel bulkhead * Split sidewalls made of trapezoidal-profile steel, foldable with central drop-in stanchion * Steel rear wall, can be slid in between the ramps – storage bracket when not in use located inside at the front bulkhead * Rear stanchions bolted * Perforated outer frame bent approx. 45 degrees with 2 t lashing capacity every 480 mm * Option to fit 3 t recessed lashing rings every 600 mm * Load securing package: 1 x 10 t UVV-certified lashing point in each front and rear corner, 2 x 8 t UVV-certified retractable lashing rings per side in outer frame, various holes in front and rear crossmember for 1.2 t lashing options Nedpfx Asl Tp Azef Aowc * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 3,000 x 620 mm (can be collapsed to 20 mm) * Rear drive-on angle approx. 860 mm * Chassis, drawbar, front wall, tailgate, folding supports, and ramps hot-dip galvanized * Axles, air tanks, flanged towing eye, and support winch painted in black * Loading height unladen approx. 940 mm * Loading height laden approx. 910 mm * Wheelbase: 1,810 mm * Tyres: 235/75R17.5 * Body side panels painted in RAL 9010 pure white * Side walls can be painted in any RAL shade at extra cost * Vehicle has a day registration (not in use) * Subject to errors and prior sale * Immediately available ex works Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 8.500 kg, skupna masa: 11.990 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Oprema: ABS, * KA-TA-R 11.9 Masterline: * Front wall and floor hot-dip galvanized * Wabco ABS * Emergency release device for spring-actuated cylinders * Drum brakes, 2 x 7 t Gigant axles * Parabolic springs with tandem equalizer unit * Height-adjustable (by 300 mm) hot-dip galvanized drawbar with 40 mm flange towing eye * Jost mechanical landing gear at the front * Two mechanical, hot-dip galvanized folding support legs at the rear * 15-pin electrical connector * Multi-chamber tail lamps * Hot-dip galvanized bolted underrun protection * Tool box made of galvanized steel sheet, mounted on right side Nwjdpfoq Hg D Hex Af Aec * Plastic quarter mudguards * Hot-dip galvanized chassis * Steel pallet 3-way tipper body * Continuous white-painted side walls at the top with internal tube reinforcement; foldable without center posts, with drop-side spring assist * Tailgate foldable and swinging, equipped with manual central locking * Hot-dip galvanized bolted rear stakes * Each corner equipped with 1 x 5 t lashing point and each side with 4 x 3 t lashing rings flush-mounted in the outer frame * 4 mm fine grain steel floor plate * Mesh hooks * Rear mounting rail for loading ramps * Removable steel side extensions, 500 mm high, 3 sides, swinging * Body reinforced and certified for load securing according to EN 12642 XL * 1 pair of aluminum drive-on ramps approx. 3,570 x 400 mm (load capacity 8 t per pair), suitable for rubber-tired and tracked vehicles * Rear lockable storage compartment recessed into the chassis below the loading area * Axles, springs, air tanks and landing gear painted in black * Tires 285/70 R 19.5 * Side panel color in RAL 9010 pure white * New vehicle with manufacturer’s warranty * Subject to error and prior sale * Immediately available ex-stock Egestorf, A7

Stanje: novo, največja dovoljena obremenitev: 14.200 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2023, * ETÜ-TA-R 19.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 11 t Gigant axles * Air suspension * Drawbar with 50 mm flanged towing eye and height adjustment of 110 mm via offset plate * Jost landing gear at front * External folding supports at rear * Plastic toolbox approx. 750 x 350 x 300 mm, right side * Lateral underrun protection * Plastic quarter mudguards * 15-pin power connector * LED lighting * Reinforcement package for drilling rig transport on chassis * 50 mm softwood floor, clamped version * Pre-fitted for subsequent installation of container locks in front of bulkhead * Bolted bulkhead made from smooth steel sheet * Split side walls made from trapezoidal-profile steel, fold-down with central folding stanchion * Sliding steel tailgate between ramps – storage bracket in front of bulkhead when not in use * Bolted rear stanchions * Perforated exterior frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to fit 3 t recessed lashing rings every 600 mm * Load securing package: 1 x 10 t certified lashing point in each front and rear corner, 2 x 8 t certified retractable lashing points per side, various 1.2 t lashing points in front and end crossmember * One-piece mechanical grid ramps with spring assist for single-person operation, approx. 3,000 x 620 mm (can be compressed to 20 mm) * Rear approach angle approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, folding supports, and ramps hot-dip galvanized * Axles, air tanks, flanged towing eye, and landing gear painted in black * Loading height unladen approx. 940 mm * Loading height laden approx. 910 mm Nedpfx Ajl Tp Alsf Aswc * Wheelbase: 1,810 mm * Tyres: 235/75R17.5 * Sideboard painted RAL 9010 pure white * Side wall painting in any RAL colour shade available at extra cost * Vehicle has temporary (day) registration (not in use) * Subject to errors and prior sale. * Immediately available ex works Egestorf, A7.

Stanje: novo, največja dovoljena obremenitev: 5.840 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2025, * KWH 8.8 ML: * TPMS (Tire Pressure Monitoring System) * EBS braking system * Drum brakes * BPW axle * Parabolic springs * Support winch at the front * Spring-assisted square tube support legs at the rear with base plates and safety lock pins for various support heights * Drawbar with 40 mm bolt coupling (height-adjustable) * 15-pin electrical connector Nsdpfou I Iqxsx Af Aowc * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and cross members * Enclosed steel fenders with splash guards * Closed side underrun protection, usable as advertising space * Plastic toolbox with base insert (installed horizontally), approx. 500 x 350 x 400 mm * Swiveling cable drum assembly, clear width between the drum arms 1,700 mm, with tension lock for fixing the drum at the support arm ends, as well as a central claw lock for securing the cable drum assembly to the chassis * Motor-hydraulic drum drive with oil motor * Valves and adjustable drive rollers with rubber lining * Hydraulic speed regulator and brake for the drum drive * Steel drum shaft, 76 mm in diameter, with centering and rotating ends * 1 pair of stepped centering cones made of polyamide * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) * Finish: hot-dip galvanized * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 16.000 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2024, * KA-TA-RT 21.0 ML: * Without ABS / EBS, approved for 40 km/h * Spring-loaded parking brake, drum brakes * Gigant axles * Tandem equalising unit with 100 mm wide parabolic springs * Support winch at the front * Mechanical drop-down supports at the rear * Fixed welded drawbar with low-maintenance ball coupling for K80 ball head coupling (adjustable by +77 mm / 33 mm via the head plate) with elevated bracket for connection lines * 12 V 7 + 4 pin power supply * LED lighting system 12 / 24 V with protective grille * 2 LED work lights at the rear, switchable from the towing vehicle without additional installations on the tractor unit * Side marker lamps with indicator function * Plastic quarter mudguards * Plastic toolbox approx. 750 x 350 x 300 mm, right side * Chassis made of high-tensile steel * Steel platform body, 3-way tipper with M-Strong side boards (fixed front wall, continuous side walls – without central stanchions – swinging via manual central locking as well as mechanically folding down with sideboard spring assist) * Hydraulic tailgate, 500 mm high, acts as a hydraulic chute with a 115° opening angle * 4 mm Hardox 450 steel floor * 1 x 7 t anchor point in each corner and 4 x 3 t lashing rings recessed and foldable on each side * Galvanised two-step access in front of the front wall (left side) * 1 pair of aluminium loading ramps (10 t / pair for axle spacing over 2,500 mm) 3,570 x 410 x 120 mm, suitable for rubber-tyred and tracked vehicles * 2 recessed ramp compartments at the rear of the chassis, cargo securing according to EN 12642 XL * --Coupling height loaded approx. 530 mm * Unloaded approx. 590 mm -- * Bodywork finished in RAL 9010 pure white * Chassis, drawbar, rear drop supports, underrun protection galvanised * Axles, air tanks, front support winch * K80 coupling painted in black tone * New vehicle with manufacturer's warranty Nwodpjr Dpzusfx Af Asc * Subject to errors and prior sale * Immediately available ex-works Egestorf

Stanje: novo, največja dovoljena obremenitev: 5.840 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2025, * KWH 8.8 ML: * RDÜ Tire Pressure Monitoring * EBS Brake System * Drum Brakes * BPW Axle * Parabolic Springs * Front Support Winch * Rear Square Tube Support Legs with Spring Assistance, Base Plate, and Safety Locking Pins for Adjustable Support Heights * Drawbar with 40 mm Bolt-on Eye (height adjustable, __ mm) * 15-pin Electrical Connector * LED Lighting * Flashing LED Side Marker Lights * Chassis made of torsion-resistant square tubes and cross beams * Enclosed steel mudguards with splash protection * Enclosed lateral underrun protection usable as advertising space * Plastic toolbox with floor insert (installed horizontally), approx. 500 x 350 x 400 mm * Swiveling cable drum carrier, clear width between drum arms 1,700 mm, with tension fastener for securing the drum to the carrier arms and a central pawl lock for securing the cable drum carrier to the chassis * Motor-hydraulic drum drive with oil motor Nwjdpfxsu I Iqls Af Aec * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft diameter 76 mm, with centering and rotating ends * 1 Pair of stepped Polyamide Centering Cones * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) * Finish: Hot-dip galvanized * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 6.110 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2025, * KWH 8.8 ML: Nsdou I Iqrjpfx Af Aewc * RDÜ Tire Pressure Monitoring * EBS Brake System * Drum Brakes * BPW Axle * Parabolic Springs * Front Support Wind * Rear spring-assisted square tube supports with base plate, safety locking bolts for various support heights * Drawbar with 40 mm bolt-on towing eye (height adjustable, mm) * 15-pin power connector * LED Lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and crossmembers * Enclosed steel mudguards with splash protection * Enclosed lateral underrun protection, can be used as an advertising surface * Plastic toolbox with floor lining (horizontal installation), approx. 500 x 350 x 400 mm * Swiveling cable drum superstructure, clear width between drum arms 1,700 mm, with clamp lock for securing drum at carrier arm ends, as well as a central claw lock to secure drum assembly to chassis * Motor-hydraulic drum drive with oil motor * Valves and adjustable, rubber-covered drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft with 76 mm diameter, with centering and rotating ends * 1 pair of centering cones made of polyamide, stepwise offset * Hydraulic pump unit with petrol engine * Fuel tank and hand starter * 13 HP with gear pump (150 bar) * 315/80 R 22.5 tires * Unladen weight 2,690 kg * Vehicle hot-dip galvanized * New vehicle with full manufacturer’s warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 5.840 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2025, * KWH 8.8 ML: * TPMS (Tire Pressure Monitoring System) * EBS braking system * Drum brake * BPW axle * Parabolic springs * Front support winch Nsdpfx Aou I Iq Eef Ajwc * Rear spring-assisted square tube supports with base plate, safety locking pins for variable support heights * Drawbar with 40 mm bolt coupling (height-adjustable in mm) * 15-pin electrical connector * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and cross members * Closed steel mudguards with splash protection * Closed lateral underrun protection, suitable for use as advertising space * Plastic toolbox with base insert (horizontal installation) approx. 500 x 350 x 400 mm * Swiveling cable drum mount, light width between drum arms 1,700 mm - with tension lock for drum securing at the ends of the support arms and a center-mounted claw lock for securing the cable drum mount to the chassis * Motor-hydraulic drum drive with oil motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft with 76 mm diameter, including centering and rotatable ends * 1 pair of stepped polyamide centering cones * Hydraulic power unit with diesel engine * Fuel tank and manual starter * 6.5 HP with gear pump (150 bar) * Surface hot-dip galvanized * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.500 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 t Gigant axles * Air suspension with lift and lowering function * Drawbar height adjustable by approx. 300 mm * Drawbar extension by 250 mm to 2,250 mm * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation necessary * 15-pin power connector * LED lighting * Landing gear at the front * Rear fold-out support legs mounted externally * Plastic toolbox approx. 858 x 500 x 500 mm mounted at the front right-hand side of the front wall * Side underrun protection * Plastic quarter mudguards * 50 mm softwood floor * Provisions in front of the bulkhead and at the rear for retrofitting 20" container locks * Bolted bulkhead made from smooth sheet metal * Steel side walls – trapezoidal profile – foldable, split once in the center * Steel rear wall can be slid in between the ramps; mounting fixture for storage inside in front of the bulkhead when not in use * Bolted rear stanchions * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Installation of 3 t drop lashing brackets possible every 600 mm – 4 lashing rings installed on each side Nwsdjl Th Dfspfx Af Asc * Each front and rear corner equipped with 1 x 6.3 t lashing ring * Various holes for 1.2 t lashing options in the front and rear cross members * One-piece mechanical grid ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be compacted to 20 mm) * Rear approach angle approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, folding support legs and ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye and landing gear painted in black * Side wall color freely selectable up to approx. 2 weeks before production date, but no metallic or special colors * --reinforced and certified body according to EN 12642 XL incl. load securing certificate-- * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Immediately available in Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.500 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Air suspension with lifting and lowering mechanism * Drawbar height adjustable by approx. 300 mm * Drawbar extension by 250 mm to 2,250 mm * Tire pressure monitoring with in-cab display via EBS signal – no vehicle-side installation required * 15-pin power connector * LED lighting * Front support winch * Rear external folding supports * Plastic toolbox approx. 858 x 500 x 500 mm, front right exterior on front wall * Side underride guard * Plastic quarter mudguards * 50 mm softwood flooring * Provisions in front of front wall and rear for retrofitting 20" container locks * Bolted smooth sheet front wall * Side walls made of trapezoidal-profile steel sheet, foldable, split 1x in the middle * Steel rear wall, insertable between the ramps, storage bracket for non-use inside at the front wall * Bolted rear stakes * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Installation of 3 t drop lashing eyes possible every 600 mm – 4 lashing rings each side installed * In each corner (front and rear) 1 x 6.3 t lashing ring * Various bores in front and end crossmember for 1.2 t lashing points * One-piece mechanical grating-type loading ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Rear drive-on slope approx. 860 mm * Chassis, drawbar, front wall, tailgate, folding supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and support winch painted in black * Side wall paint color freely selectable up to approx. 2 weeks before production date, metallic and special colors excluded * --Reinforced and certified body according to EN 12642 XL incl. load securing certificate-- * New vehicle with manufacturer’s warranty * Subject to errors and prior sale Nedpfxel Thvxo Af Ajwc * Available immediately Egestorf

Stanje: novo, največja dovoljena obremenitev: 8.450 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 22.420 mm, višina nakladalnega prostora: 1.500 mm, Leto izdelave: 2024, * KA-TA-R 11.9 Masterline: * includes 1 m mesh side extensions * EBS brake system * Emergency release device for spring brake cylinders * RDÜ tire pressure monitoring system * Drum brakes * 2 x 5.5 t BPW axles * Parabolic springs with tandem equalizing unit * 300 mm height-adjustable hot-dip galvanized tow bar with 40 mm flange towing eye * Jost mechanical landing gear at the front * Two mechanical hot-dip galvanized folding supports at the rear * Tool box made of galvanized steel sheet, right side * 15-pin electrical connector * Bolted underrun protection with LED tail lights * Plastic quarter mudguards * Net hooks mounted on sides and rear in the central locking compartments as well as 3 external hooks on the front wall * Hot-dip galvanized chassis * Steel 3-way tipper body, fully galvanized * Continuous, fold-down side walls without central stanchion, equipped with drop-side spring lifter * Tailgate fold-down and swinging via manual central locking * Hot-dip galvanized, bolted rear stanchion * One recessed folding 5 t lashing ring per corner and 4 folding 3 t lashing rings on each side * Recessed, folding lashing rings in the outer frame * 4 mm steel floor plate * Rear ramp channel for loading ramps * Body reinforced with load securing certificate according to EN 12642 XL * 1 pair of aluminum loading ramps approx. 3,570 x 400 mm (load capacity 8 t / pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment at the rear, recessed under the loading surface in the chassis * 235/75 R 17.5 tires * Axles, springs, air tanks, drawbar, and supports painted in black * Side wall color hot-dip galvanized * 1-meter mesh side extensions, galvanized * Sample photos * New vehicle with manufacturer warranty Nwjdpfxsp Ncl Sj Af Asc * Errors and prior sale excepted * Available immediately ex works Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 10.700 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 1.500 mm, Oprema: ABS, * KA-TA-R 14.4: * Front wall and floor hot-dip galvanized * Wabco ABS * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem equalizer unit * Height-adjustable hot-dip galvanized drawbar (approx. 300 mm) with 40 mm flanged towing eye * Jost mechanical landing gear at the front * Rear: 2 mechanical hot-dip galvanized folding supports * 15-pin power connector * Multi-chamber tail lights * Hot-dip galvanized bolted underrun protection * Tool box made of galvanized steel sheet, mounted right side * Plastic quarter mudguards Nwodsp Ncmaspfx Af Ajc * Hot-dip galvanized chassis * Steel pallet three-way tipper body * Continuous sidewalls in white, top with internal pipe reinforcement, foldable without center stanchions, with drop side spring assist * Tailgate foldable and swinging, manual central locking * Hot-dip galvanized screwed rear stanchions * Each corner equipped with 1 x 5 t lashing point, plus 4 x 3 t lashing rings recessed into the outer frame per side * 4 mm fine-grained steel floor plate * Net hooks, rear ramp mounting rail * Prepared for subsequent fitting of drop side extensions * Reinforced body with load securing certificate per EN 12642 XL * 1 pair of aluminium ramps approx. 3,570 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable rear storage compartment recessed into the chassis below the loading area * Axles, springs, air reservoir, and landing gear painted in a shade of black * Side walls painted RAL 9010 pure white * 1 meter galvanized mesh side extensions * Tyres: 285/70 R 19.5 * Sample images * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Immediately available ex works Egestorf, A7

Stanje: novo, največja dovoljena obremenitev: 16.000 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2024, * KA-TA-RT 21.0 ML: * Without ABS / EBS, approved for 40 km/h * Spring-loaded parking brake, drum brakes * Gigant axles * Tandem compensating aggregate with 100 mm wide parabolic springs * Support windlass at the front * Mechanical drop-down supports at the rear * Fixed welded drawbar with low-maintenance K80 ball coupling (offset by +77 mm / 33 mm adjustable via head plate) with elevated gantry for connection lines * 12 V 7 + 4 pole electrical wiring * LED lighting system 12 / 24 V with protective grille * 2 LED work lights at the rear, switchable from towing vehicle without vehicle-side installation * Side marker lights with indicator control * Plastic quarter mudguards * Plastic toolbox approx. 750 x 350 x 300 mm, right side * Chassis made of fine-grain steel * Steel Pal.- three-way tipper body with M-Strong side walls (fixed front wall, continuous side walls without central stanchions, swinging via manual central locking and mechanically foldable with side wall spring lifter * Hydraulic tailgate, 500 mm high, acts as a hydraulic chute with a 115° opening angle * 4 mm Hardox 450 steel floor * In each corner 1 x 7 t, and on each side 4 x 3 t recessed and foldable lashing rings * Hot-dip galvanized two-step access ladder in front of the front wall (left side) Nwjdpfer Dpz Hsx Af Ajc * 1 pair of aluminum ramps (10 t/pair with axle distance over 2,500 mm) 3,570 x 410 x 120 mm, suitable for rubber-tired and tracked vehicles * 2 rear-integrated storage compartments for aluminum ramps in the chassis; load securing according to EN 12642 XL * --Coupling height loaded approx. 530 mm * unloaded approx. 590 mm-- * Body paint finish in RAL 9010 pure white * Chassis, drawbar, rear drop supports, underrun protection are hot-dip galvanized * Axles, air tanks, front support windlass * K80 coupling painted in a shade of black * New vehicle with manufacturer warranty * Errors and prior sale reserved * Immediately available ex Egestorf

Stanje: rabljeno, lastna masa: 3.320 kg, največja dovoljena obremenitev: 10.180 kg, skupna masa: 13.500 kg, konfiguracija osi: 2 osi, prva registracija: 12/2003, naslednji pregled (TÜV): 09/2026, dolžina tovornega prostora: 5.040 mm, vzmetenje: jeklo, velikost pnevmatike: 285/70R19,5 148/145J, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 285/70R19,5 148/145J, velikost zadnje pnevmatike: 285/70R19,5 148/145J, voznikova kabina: drugo, emisijski razred: noben, Oprema: ABS, zavorni sistem na stisnjen zrak, Sidrne ušesa, doplačilo za rampe: 800 €, -- Pridržujemo si pravico do tiskarskih napak, sprememb in drugih nepravilnosti, slike so simbolične --, Več podatkov na zahtevo!, Več podrobnosti: ! Nwsdpfx Afsynr Sgs Aoc

Stanje: rabljeno, lastna masa: 7.340 kg, največja dovoljena obremenitev: 22.660 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2012, dolžina tovornega prostora: 9.200 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, Oprema: ABS, zavorni sistem na stisnjen zrak, Dolžina nakladalne površine cca 9.200 mm, nakladalna višina cca 900 mm, 16 pritrdilnih obročev, vozilo se prodaja po naročilu, pridržujemo si pravico do tiskarskih napak, napak in sprememb, slike so vzorčne. Več podatkov na: !, More Details: ! Nwsdjymw Azopfx Af Asc

Stanje: rabljeno, lastna masa: 3.680 kg, največja dovoljena obremenitev: 10.720 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, prva registracija: 11/2021, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, vzmetenje: jeklo, velikost pnevmatike: 385/55R19,5 156J, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 385/55R19,5 156J, velikost zadnje pnevmatike: 385/55R19,5 156J, voznikova kabina: drugo, emisijski razred: noben, Oprema: ABS, zavorni sistem na stisnjen zrak, KOT NOVO, široke pnevmatike, kiper ploščad CINKANA, 12 pritrdilnih obročev, stranske stene 600 mm, doplačilo za rampe 1.000 €, -- pridržujemo si pravico do tiskarskih napak, sprememb in napak, vzorčne slike --, Več podatkov na zahtevo! Nwsdeympl Iepfx Af Asc

Stanje: rabljeno, lastna masa: 5.750 kg, največja dovoljena obremenitev: 24.250 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, prva registracija: 01/1993, vzmetenje: jeklo, velikost pnevmatike: 235/75R17,5 141/140J, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75R17,5 141/140J, velikost zadnje pnevmatike: 235/75R17,5 141/140J, voznikova kabina: drugo, emisijski razred: noben, Oprema: ABS, zavorni sistem na stisnjen zrak, -- Pridržujemo si pravico do tiskarskih napak, napak in sprememb, vzorčne slike --, Več podatkov na: !, Več podrobnosti: ! Nwodeyl T Htjpfx Af Aec

Stanje: rabljeno, lastna masa: 7.340 kg, največja dovoljena obremenitev: 22.660 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2012, dolžina tovornega prostora: 9.200 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, Oprema: ABS, zavorni sistem na stisnjen zrak, Dolžina nakladalne površine cca 9.200 mm, nakladalna višina cca 900 mm, 16 pritrdilnih obročev, vozilo se prodaja po naročilu, pridržujemo si pravico do tiskarskih napak, napak in sprememb, slike so vzorčne. Več podatkov na: !, More Details: ! Nsdpoylicwsfx Af Aewc

Stanje: novo, vzmetenje: drugo, barva: drugo, vrsta prenosa: drugo, voznikova kabina: drugo, emisijski razred: noben, Equalizer block for low-bed semi-trailers incl. container locks. Price per equalizer block. -- Subject to typographical errors, mistakes, and changes. Sample images --. More data at: !, More Details: ! Nwedoyi Euqopfx Af Aoc

Stanje: rabljeno, lastna masa: 4.550 kg, največja dovoljena obremenitev: 13.450 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 10/2016, dolžina tovornega prostora: 6.540 mm, širina tovornega prostora: 2.480 mm, vzmetenje: zrak, velikost pnevmatike: 235 / 75 R 17,5, barva: bež, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235 / 75 R 17,5, velikost zadnje pnevmatike: 235 / 75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, 10 pairs of lashing rings, loading height approx. 900 mm, customer vehicle, -- subject to misprints, errors and changes -- sample images --, More data at: !, More Details: ! Njdpjyiladefx Af Aewc

Stanje: rabljeno, največja dovoljena obremenitev: 9.400 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 07/2020, dolžina tovornega prostora: 6.300 mm, širina tovornega prostora: 2.480 mm, Int.-št.: ZANDT Zelo dobro vzdrževana tandem šasija s kesonom ZANDT Cargo * TAT B 110 * Keson * Ojačano leseno dno * Težko nosilne pritrdilne tirnice * Dvoosna tandem os * Široke pnevmatike * Nastavljiva vlečna kljuka * Največja dovoljena masa 11.900 kg * Zelo dobro stanje Možna je menjava staro za novo Financiranje od 3,99% Nodpoymuz Uefx Af Aewc Pridržujemo si pravico do napak in vmesne prodaje! Podatki v tem oglasu so neobvezujoči opisi in ne predstavljajo zagotovljenih lastnosti. Prodajalec ne prevzema nobene odgovornosti za tipkarske ali prenosne napake. Oprema iz oglasa se preveri posebej. Vsi podatki v oglasih so neobvezujoči! Dostava po celotni Nemčiji na zahtevo Delovni čas: ponedeljek do četrtek od 9:00-17:00, petek od 9:00-14:00 ali po dogovoru!

Stanje: rabljeno, največja dovoljena obremenitev: 9.400 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 07/2020, dolžina tovornega prostora: 6.300 mm, širina tovornega prostora: 2.480 mm, Int. št.: ZANDT zelo dobro vzdrževana tandem ploščadna prikolica Nodpfx Afjymuz Ij Aewc ZANDT Cargo * TAT B 110 * ploščad * ojačan lesen pod * pritrdilne tirnice za težke tovore * tandem z dvema osema * široke pnevmatike * nastavljivo vlečno oje * dovoljena skupna masa 11.900 kg * zelo dobro stanje Možnost menjave starega za novo Financiranje od 3,99 % Napake in vmesna prodaja pridržane! Podatki v tem oglasu so nezavezujoči opisi in ne veljajo kot zagotovljene lastnosti. Prodajalec ne prevzema odgovornosti za tipkarske napake ali napake pri prenosu podatkov. Oprema, navedena v oglasu, je treba posebej preveriti. Vsi podatki v oglasih so nezavezujoči! Dostava po celotni Nemčiji na zahtevo Delovni čas: ponedeljek do četrtek od 9:00 do 17:00 petek od 9:00 do 14:00 in po dogovoru!!!

Stanje: rabljeno, največja dovoljena obremenitev: 4.960 kg, skupna masa: 10.500 kg, prva registracija: 04/1993, naslednji pregled (TÜV): 01/2026, dolžina tovornega prostora: 6.260 mm, širina tovornega prostora: 2.430 mm, višina nakladalnega prostora: 2.430 mm, prostornina tovornega prostora: 37 m³, 2-axle tandem refrigerated trailer 7 m with tail lift, 1 ton capacity. * THERMOKING LND-II MAX (diesel engine) and standby cooling 380 V ELECTRIC * Vehicle No. for customer inquiries: 4593 No liability for typographical or printing errors. Sale to commercial customers only. Errors and prior sale excepted. * Subject to change, prior sale, and errors. The description serves for the identification of the vehicle and does not constitute a legal warranty as per sales law. The purchase agreement description is decisive. * TOP SERVICE + QUALITY * We can provide you with tailored LEASING, FINANCING, or HIRE PURCHASE offers. Warranty insurance available on request from the insurer. * TÜV (roadworthiness inspection) / UVV tail lift inspection / tachograph calibration and installation of OBU device by our local partners. * Export license plates for 30 days. All necessary export customs documents can be provided upon request, but must be requested individually. * TOLL for Toll Collect can be arranged in-house. * Free transfer from Stuttgart Airport or Metzingen train station (Württ) * TRAIN STATION FOR ARRIVAL: 72555 METZINGEN/WÜRTT. * FOR ENGLISH * Andreas Pittas * Thomas Pittas * Alexander Pittas * Robin Pittas WHATSAPP Number * * Nwedpfsykxflox Af Ajc ---- Visit us on our website at * Over 200 vehicles in stock at all times