Tristrani nagibni priklopnik

MÜLLER-MITTELTAL 11,9 to Tandemkippanh. mit Agra vorbereitung

Stanje: novo, največja dovoljena obremenitev: 8.650 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * KA-TA-R 11,9 Masterline ----Zavore: * Wabco EBS * Sistem za sprostitev v primeru izrednih razmer za vzmetne zračne cilindre * Bobnaste zavore ----Os: * 2 x 5,5 t BPW osi ----Vzmetenje: * Parabolična vzmet z tandem sistemom za izravnavo ----Vlečna prikolica / prirobnična vlečna prikolica: * Vlečna prikolica z nastavljivo višino za 300 mm in 40 mm prirobnična vlečna prikolica ----Elektrika / osvetlitev: * Sistem za nadzor tlaka v pnevmatikah RDÜ * Večnapetostni sistem * 15-polni električni vtič * 12 V, 13-polni dodatni kabel * Podaljšani priključni kabli za gozdarska in kmetijska vlečna vozila * LED zadnje luči ----Splošni dodatni deli: * Mehanski oporni dvigalnik spredaj * Spredaj 2 mehanska zložljiva oporna nogica * Plastična orodjarna škatla na desni strani * 2-stopenjska stopnica na levi strani, v smeri vožnje, spredaj * Zaščita proti podiranju, pritrjena z vijaki * Plastični četrtni blatnik ----Nakladalna platforma: * Obešane mreže na straneh in zadaj v ležajih osrednjega zaklepanja, ter 2 kosa na čelni steni * Jeklena 3-stranska nakladalna platforma (kontinuirana stranska stena – brez osrednjih vzdolžnikov – zložljiva z vzmetjo za stransko steno, zložljiva zadnja vrata in nihajno preko ročnega osrednjega zaklepanja * 4 mm jeklena pločevina * Nosilna tirnica zadaj za nakladalne rampe ----Varovanje tovorja: * Na vsakem vogalu 1 x 5 t pritrdilno vrv * Ter na vsaki strani 4 x 3 t pritrdilne točke, vgrajene v zunanji okvir ----Rampe: Bodpol Thw Isfx Agtjln * 1 par aluminijastih nakladalnih ramp, približno 3.310 x 400 mm (nosilnost 8 t / par) za vozila s pnevmatikami in gosenicami * Zaklepni prostor na zadnji strani pod nakladalno površino, vgrajen v šasi ----Pnevmatike: * Pnevmatike 385/55 R 19,5 ----Barvanje: * Šasi, vlečna prikolica, nakladalna platforma, čelna stena, zložljive oporne nogice in zadnji vzdolžniki, vroče pocinkani * Os, vzmeti, zračni rezervoar, prirobnična vlečna prikolica in oporni dvigalnik, pobarvani v črni barvi * Barvanje stranskih sten v barvi RAL - 9010, čista bela ----Informacije: * Nadgradnja je ojačana z certifikatom za varovanje tovorja v skladu s standardom EN 12642 XL * Novo vozilo z garancijo proizvajalca * Pridržujemo si pravico do sprememb in napak ----Dobavni rok: * Dostavljivo približno v 47. tednu leta 2026

Stanje: novo, največja dovoljena obremenitev: 37.390 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Traction aid for shunting purposes engaged on the first axle via EBS (without truck-side installation) * Last axle as trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle from the driver's cab for shunting via EBS (without truck-side installation) ----Suspension: * Air suspension with lifting and lowering function as well as RtR valve ----Electrics / Lighting: * Smart Board mounted on trailer as info tool with pressure sensors for total axle load display * 15-pin electrical connector * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * 2 extra LED reversing lights * 7-pin socket at the rear for additional length lighting * Side marker lights with indicator activation * Tire pressure monitoring system with display option in the truck via EBS signal (without truck-side installation) ----General attachments: * Side underrun protection * Landing gears at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the headboard crossmember (without spare wheel) * Mechanically adjustable warning sign packages at the front and rear * Swivel arm as carrier for connection cables from truck to semi-trailer ----Lowbed platform: * Second kingpin position * Fifth wheel platform with 45° bevelled front corners and front toolbox made of galvanised, powder-coated steel sheet, W = 2,480 mm x H = 500 mm x L = 665 mm with folding lid * Side aluminium drop sides, 400 mm high (in RAL custom colour), foldable and removable * Rear wall -150 mm- high plug-in * Rear slope on the saddle platform to the lowbed approx. 700 mm long with chequer plate covering and a perforated strip at the end for attaching aluminium loading ramps * Fifth wheel platform with 50 mm clamped wooden planks and lowbed platform with 60 mm clamped wooden planks Bljdpfx Ajtpta Dsgtsn * Tread plate over the axles * 9 x mechanical folding wideners to 3 m overall width, not in rear slope (widening planks available with sealed crosswise storage compartment under the loading area) * 3 mounting shafts under the saddle platform for the storage of either aluminium loading ramps or wooden planks for wheel well covering ----Load securing (LaSi-package): Fifth wheel platform: * Perforated outer frame, 45° angled, with hole pattern for lashings (2 t lashing capacity per tie-down point at a minimum spacing of 480 mm) * 3 x 13.4 t recessed lashing rings per side in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal members after the cranking, 1 x above the central axle next to the longitudinal member) Lowbed platform: * 3 x 13.4 t lashing rings per side on the outer frame (1 x at the start of the cranked platform, 1 x at the start of the access slope, 1 x at the end of the access slope) * 2 x 10 t lashing rings per side (1 x between the front wheel well and 1st axle, 1 x between the 2nd and 3rd axle) * 3 x 5 t lashing rings per side bolted to the outer frames of the wheel wells (2 at the front wheel well, 1 at the rear wheel well) ----Excavator arm rest: * Extended excavator arm rest from end of last rigid axle over steering axle to end crossmember, continuous with internal reinforcing profile approx. W = 770 mm x D rear = 270 mm / D front = 170 mm * 2 x 6.4 t lashing rings per side in the exca

Stanje: novo, največja dovoljena obremenitev: 28.860 kg, skupna masa: 37.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes * 3 x 11 t axles * Air suspension with lift and lower function, including RtR valve * Start assist for shunting, applied to first axle via EBS – no truck-side installation – when lift axle is raised +30 mm ride height * Smart-Board installed on trailer as an info tool, with pressure sensors for total axle load indication * Rear axle as self-steering axle with electro-pneumatic steering lock * Steering lock for trailing axle controlled from driver’s cab for maneuvering purposes via EBS (no truck-side installation) * 2" king pin * 1 lift axle * Side underrun protection * Front aluminium drop support legs and rear swing-down supports on chassis * Alcoa LVL One aluminium wheels * 15-pin electrical connector Bodowh Hdxspfx Agtjln * LED lighting 12/24 V * Removable rear LED beacon * 2 additional LED reverse lights * 2 LED work lights mounted on trailer sides – no truck-side installation * 7-pin power socket at rear for overlength lighting * Side marker lamps with indicator activation * Tyre pressure monitoring system with display in truck via EBS signal (no truck-side installation) * Mechanically adjustable warning sign sets front and rear * Straight steel fenders * Saddle platform with 45° bevelled front corners and front toolbox made of galvanized, powder-coated steel sheet (B = 2,480 x H = 500 x L = 665 mm), top hinged lid and side doors at the beveled corners * 400 mm aluminium side boards (RAL 9010 pure white) fold-down and removable, mounted laterally on the saddle platform * Rear wall –150 mm– slotted in * Tapered rear on the saddle platform to lowbed approx. 700 mm long with chequer plate covering and lashing bar at end for attaching aluminium ramps * Saddle and lowbed platform with 50 mm clamped wooden planks * Tear plate above the axles * Prepared for 3 mounting shafts under the saddle platform for optional aluminium ramps storage * Swing arm as a carrier for connection lines from truck to trailer * Load securing package consisting of: outer frame of the saddle platform with punched holes, 45° bent and hole-pattern for lashing devices (2 t lashing force per point, min. 480 mm spacing), side-mounted 2 x 6.3 t recessed lashing rings per side, 1 x 16.5 t lashing ring per side at incline from lowbed to saddle platform, 2 pairs 16.5 t lashing rings in lowbed (1x on longitudinal beams after the step, 1x above the centre axle beside longitudinal beam), side 3 x 13.4 t lashing rings per outer frame (1x at start of platform step, 1x start of ramp slope, 1x end of ramp slope), 3 x 10 t each side (2x between front wheel recess and 1st axle, 1x between 2nd and 3rd axle), 3 x 5 t per side screwed to the wheel recess outer frames (2 at front, 1 at rear recess) * Extended excavator arm trough from end of last rigid axle over steering axle to end cross member, continuous with internal reinforcement profile approx. W = 770 mm x D rear = 270 / D front = 170 mm; each side 2 x 6.4 t lashing rings in the arm trough * Each side two wheel recesses, 390 mm deep and 640 mm wide for transporting wheel loaders with wheelbase 3,000–3,590 mm, tyre diameter up to 1,760 mm – retractable covers – * Second retractable cover ...