Faymonville Standardna Struktura nakup rabljenega (184)

Stanje: rabljeno, konfiguracija osi: 3 osi, prva registracija: 09/2014, skupna dolžina: 13.900 mm, skupna širina: 2.540 mm, vzmetenje: zrak, Leto izdelave: 2014, Dodatne informacije: Znamka: FAYMONVILLE Model: Telemax Konstrukcija: platforma (platforma, dolžina L = 13758–25258 mm, raztegljiva) Letnik: 09.2014 VIN: YAFSR314000015733 Vzmetenje: zračna vzmet Zavore: bobnaste Dimenzije: D/Š: 13900 mm / 2540 mm Mase: bruto/neto: 75000 kg / 15810 kg RAZTEGLJIVA / VSE OSI VODLJIVE Letnik modela: 2014 Vrsta vzmetenja: zračno vzmetenje Zavore: bobnaste Dvignljiva os: dvignljiva os Vrsta vzmetenja: zračno vzmetenje Zavore: bobnaste Krmiljenje: krmiljenje Vrsta vzmetenja: zračno vzmetenje Isdpfxezwkp Ij Ai Sebb Zavore: bobnaste Krmiljenje: krmiljenje = Dodatne informacije = Vzmetenje: zračno vzmetenje Prednja os: dvignljiva os Srednja os: vodljiva Zadnja os: vodljiva Prazna teža: 12.500 kg Nosilnost: 46.500 kg Dovoljena skupna masa: 59.000 kg Za dodatne informacije se obrnite na Marka Ševtšenka ali Alejandra Goyenecheja.

Stanje: rabljeno, konfiguracija osi: > 3 osi, Leto izdelave: 2009, Naprodaj je Faymonville MultiMAX 4-osni pol-prikolica nizkoploščad / globoka prikolica iz leta 2009 z dovoljeno skupno maso 71.000 kg. Prikolica ima 4 osi in hidravlične nakladalne rampe. Izjemno primerna je za prevoz gradbenih strojev, delovnih strojev, nakladalnikov, bagrov, goseničarjev in težkih gospodarskih vozil. Proizvajalec: Faymonville Model / Tip: MultiMAX / TL STZ-4AU Vrsta vozila: pol-nizkoploščad / nizkoploščadna polprikolica Prva registracija: 26.02.2009 Št. šasije / VIN: YAFTL409100009798 Število osi: 4 Dovoljena skupna masa: 71.000 kg Lastna masa po homologaciji: 16.800 kg Nosilnost (preračunano): pribl. 54.200 kg Obremenitev na os: 11.500 kg Obremenitev na zatič (pivot): 25.000 kg Dolžina vozila po homologaciji: 17,76 m Širina po homologaciji: 2,76 m Barva: bela / bež Isdpfszhu A Hex Ai Sebb 4-osna pol-nizkoploščad Hidravlične nakladalne rampe zadaj Razširljiva nakladalna površina / stranske razširitve Globokonosna izvedba za prevoz strojev Podporne noge spredaj Stranska orodjarna / zaboj za shranjevanje Rezervno kolo na labodjem vratu Privezne točke vzdolž nakladalne površine Robusten jeklen okvir Labodji vrat izvedba Osvetlitev in opozorilne table zadaj Primerna za prevoz težkega tovora in gradbenih strojev Krmarjena os = Dodatne informacije = Lastna masa: 16.800 kg Nosilnost: 54.200 kg Skupna dovoljena masa: 71.000 kg

Stanje: novo, največja dovoljena obremenitev: 46.800 kg, skupna masa: 58.000 kg, konfiguracija osi: > 3 osi, Oprema: ABS, Na naši spletni strani najdete naš celoten nabor vozil, ki so na voljo takoj ali v kratkem roku. Izbor iz opreme: Celotna oprema na zahtevo. "Labodje vrat": * "Labodje vrat" s poševnimi robovi spredaj, približno 45° in z zadnjo poševnostjo približno 750 mm x 10° * 3 pari pritrdilnih obročev (nosilnost 5.000 daN) * Prevleka iz trdega lesa, debeline približno 30 mm Nosilna plošča, raztegljiva različica: * z zadnjo poševnostjo približno 1.000 mm x 8° Iodpfx Aezk S Dmei Sjbb * 5 parov pritrdilnih obročev, z zunanjim mehanizmom za zlaganje (nosilnost 5.000 daN) * 3 pari pritrdilnih obročev, z zunanjim mehanizmom za zlaganje (nosilnost 10.000 daN) * 1 par pritrdilnih obročev, nameščen vodoravno spredaj na nosilni plošči (nosilnost 10.000 daN) * Vrezanine v zunanjem okvirju nosilne plošči za pritrditev zategovalnih trakov (nosilnost 2.000 daN) * Prevleka iz trdega lesa, debeline približno 48 mm, nad osmi protizdrsna prevleka. Osi: * Osi in vzmetenje BPW * Prva os je fiksna, vse ostale osi pa so hidravlično-mehansko sinhronizirane * Tehnična obremenitev osi: 12.000 kg na os * Zračno vzmetenje z ventilom za dvigovanje in spuščanje * Orodje za osi * Pnevmatike * 245/70 R 17.5 3PMSF * Indeks obremenitve (146/146 F) * TPMS: Sistem za nadzor tlaka v pnevmatikah, v skladu s standardom ECE R 141 Podporne noge * Podporne noge JOST (mehanske) z 2-stopenjsko prestavo za približno 24 t dvigalne nosilnosti (približno 50 t preizkusne nosilnosti) Zavorna naprava * v skladu s predpisi EU z EBS-E (4S3M) Barvanje * Celotna jeklena konstrukcija, avtomatsko obdelana s peščanjem po varjenju * Drugo peskanje s korundom za optimalno oprijemljivost prevlečnega sistema * HRM-metalizacija celotnega šasije vozila s pomočjo ZINACOR 850 (85 % cink/15 % aluminij) za zagotavljanje najboljše korozijske zaščite * Končno barvanje z 2 plastmi 2K lakom * enobarvno, v barvi RAL 3002 Karminrot, v skladu s sistemom RAL 841GL * Platišča v srebrnosivi barvi. Zadnji del metaliziran in pobarvan v barvi RAL 9010 (čista bela) * Metalizirano barvanje ni mogoče * Barvna prevleka preizkušena s testom solne megale v skladu s standardom ISO 9227-NSS * Zapiranje votlin s specialnim voskom Jeklena konstrukcija * iz visoko trdnih finozrnatih jekel * Kakovost jekla: S355J2+N/S355MC (meja tečenja 355 MPa), S690QL/S700MC (meja tečenja 690 MPa) Električni sistem * v skladu s predpisi EU Osvetlitev * 24 Volt ASPÖCK-NORDIK (ASS3) * Vse LED stranske gabaritne luči utripajo skupaj s smerokazom * ASPÖCK-UNIBOX na priključni letev spredaj s vtičnicami 24N, 24S & 15 polna * Priključek v skladu z ISO. 24N ISO-1185 24S ISO-3731 15 polna ISO-12098 Vključno z naslednjo dodatno opremo: * 2-palčni kraljevi priklop * Pocinkana jeklena sprednja stena, približno 400 mm visoka * Elektro-hidravlična agregat (± 45 kg) * Pomik sprednje in zadnje osi s kabelskim daljinskim upravljanjem preko tipk, z nadzorom ene osi (brez vgradnje v centralno mazalno enoto) * 1 par potopljenih pritrdilnih obročev vzdolž centralnega nosilca zadaj v poševnem delu (nosilnost 10.000 daN) (± 3 kg) * Na "labodjem vratu" aluminijaste bočne stene in zadnja stena, vstavljivi, približno 2.440 x 400 mm (D x V) * Zadnje pocinkane vstavne ograje je mogoče odstraniti. (dolžina nadgradnje približno 2.560 mm) (± 46 kg) * Orodje, galvanizirano, integrirano v poševni del "labodjega vrata" (± 47 kg) * 3 pari WADER žeepov za kontejnerje na nosilni plošči za 20' (30?) ali 40'? kontejner (± 30 kg) * 6 parov žeepov za vstavne ograje, približno 100 x 50 mm, v zunanjem okvi

Stanje: rabljeno, konfiguracija osi: 3 osi, prva registracija: 04/2009, skupna dolžina: 13.800 mm, skupna širina: 2.550 mm, vzmetenje: zrak, Leto izdelave: 2009, Dodatne informacije: Znamka: FAYMONVILLE Model: Telemax Konstrukcija: nizkopodna prikolica (platforma, dolžina L = 13330–17530 mm, raztegljiva / višina H = 1400 mm) Letnik: 01.2008 Vzmetenje: zračni sistem Zavore: bobnaste Dimenzije: D/Š: 13800 mm / 2550 mm Mase: polna/prazna: 59000 kg / 11310 kg VSE OSJE SO KRMILJENE Letnik modela: 2007 Iodpfxozhvqle Ai Sobb Vrsta vzmetenja: zračni sistem Zavore: bobnaste Vrsta vzmetenja: zračni sistem Zavore: bobnaste Krmiljenje: krmiljenje Vrsta vzmetenja: zračni sistem Zavore: bobnaste Krmiljenje: krmiljenje = Več informacij = Vzmetenje: zračno vzmetenje Srednja os: krmiljena Zadnja os: krmiljena Prazna teža: 11.310 kg Nosilnost: 47.690 kg Največja dovoljena masa: 59.000 kg Za več informacij se obrnite na Marka Ševtšenka ali Alejandra Goyenecheja.

Stanje: rabljeno, največja dovoljena obremenitev: 25.630 kg, skupna masa: 38.000 kg, konfiguracija osi: 2 osi, prva registracija: 11/2024, naslednji pregled (TÜV): 11/2026, Oprema: ABS,

Stanje: novo, največja dovoljena obremenitev: 45.115 kg, skupna masa: 53.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, Dodatna vozila na voljo Izvleček iz opreme. Popoln seznam opreme na zahtevo. Tovorna površina: - Tovorna površina z okoli 30 mm debelim trdim lesom - 8 parov zložljivih pritrdilnih obročev (nosilnost LC 10.000 daN) Podporne noge: - JOST mehanske podporne noge z dvojnim menjalnikom, dvižna zmogljivost ca. 24 t (preskusna obremenitev ca. 50 t) Pnevmatike: - 385/65 R 22.5 - TPMS sistem za nadzor tlaka v pnevmatikah po standardu ECE R 141. - Prenos podatkov k tovornemu vozilu poteka prek standardiziranega EBS vmesnika (ISO 11992). - Vozilo mora podpirati prikaz in prenos podatkov. Premi in vzmetenje: - BPW-premi, tehnično dovoljene osne obremenitve po 10.000 kg - 1. in 3. os hidro-mehansko prisilno vodeni, nameščeni na vrtljivem ležaju, 2. os toga - Zračno vzmetenje s funkcijo dviga in spusta - Orodje za osi Zavorni sistem: - Wabco zavorni sistem po EU predpisih z EBS-E (4S3M), brez povezovalnih vodov k vlačilcu Električna oprema: - Električna oprema po zahtevah EU, razsvetljava 24 V ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX spredaj s priključki 24N, 24S & 15-polni (po ISO: 24N ISO-1185, 24S ISO-3731, 15-polni ISO-12098) Jeklena konstrukcija: - Jeklena konstrukcija iz visoko odpornega finega zrnatega jekla - Kakovost jekla: S355J2+N/S355MC (meja tečenja 355 MPa), S690QL/S700MC (meja tečenja 690 MPa) Barvanje: - Popolna jeklena konstrukcija je po varjenju avtomatsko peskana (s strojnim peskanjem) - Druga obdelava s korundom za boljši oprijem zaščitnih premazov - Končni premaz z dvema slojema 2K barve, enobarvno v RAL 3002 karmin rdeči po standardu RAL 841GL - Zadnji del kovinsko prevlečen in lakiran v RAL 9010 (čista bela) - Platišča v srebrni barvi - Premaz testiran s preskusom v slanem razpršilu po ISO 9227-NSS - Votle dele zaščiteni s posebnim voskom Oprema: Iodpfxozhd Nio Ai Sjbb - Tovorna površina z okoli 30 mm trdim lesom - 2" King pin - Pocinkana jeklena čelna stena (EN12642-XL), pribl. 1.200 mm visoka - Spredaj rumeno-rdeče pnevmatske spojke na pocinkani priključni letvi - 4 zagozde s pritrjevalom spredaj - Odlagalno mesto za približno 1.000 mm dolge snemljive stranice v osrednjem nosilcu zadaj - Na labodjem vratu in na zadnji plošči levo/desno držalo za opozorilne table vklj. z vtičnico - Rumen odsevni trak po zahtevah EU po obodu in zadaj na priklopniku - 10 parov žepov za vzdolžne stranice (pribl. 100 x 50 mm) v zunanjem okviru - Evropske odsevne table (rdeče-rumene) na zadku priklopnika - Držalo za rotacijsko opozorilno luč na zadku - Blatnik na zadku - Navodila za uporabo in opis na USB ključku - Oznake za maksimalno hitrost 80 km/h zadaj in ob strani - Elektro-hidravlična enota - Vlečna spojka za manevriranje z ojačano nosilno traverso - Manometer za določanje osnih obremenitev vključno z obremenitveno shemo - Centralno mazalni sistem BEKAMAX (Pico) z običajno mastjo NLGI-2 in snemljivim zaščitnim pokrovom - Krmiljenje osi spredaj in zadaj s kablom (daljinsko upravljanje s tipkami), z nadzorom izravnanosti osi (brez namestitve v vlačilcu) - 7 parov pocinkanih snemljivih stranic (pribl. 100 x 50 mm, pribl. 1.000 mm visoke) - 4 prečne vrste žepov za stranice, nameščene prečno v tovorni površini (pribl. 100 x 50 mm) - Spiralni kabel za napajanje elektro-hidravlične enote in/ali električnega vitla (pribl. 35 mm², pribl. 3,5 m dolg, max. 250A) med priklopnikom in vlačilcem z NATO-NATO konektorjem Dostopna lestev...

Stanje: rabljeno, lastna masa: 9.600 kg, največja dovoljena obremenitev: 30.400 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, prva registracija: 12/2011, dolžina tovornega prostora: 13.200 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 800 mm, vzmetenje: zrak, velikost pnevmatike: 205/65R17.5, barva: zelen, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Vehicle location: Bovenden, 4 axles, SAF axles, air suspension, lifting and lowering function, 3rd and 4th axles steered, ABS (anti-lock braking system), extendable, lashing rings, attachable loading ramps, front support, rear support, side aluminium underrun protection, storage box. Body: 4-axle low-bed semi-trailer with attachable loading ramps, SAF axles, 3rd and 4th axles steered, 13 pairs of lashing rings, 10 pairs provisions for insertable stanchions, 13,200 mm loading length fully retracted, 16,800 mm loading length fully extended, 800 mm load height in the low-bed area, low-bed length retracted approx. 9,500 mm, TÜV inspection due, aluminium ramps available at an extra charge of EUR 1,500. ACCESSORY INFORMATION WITHOUT WARRANTY, subject to change, prior sale and errors excepted. Isdpfxoxxkqzj Ai Ssbb

Stanje: novo, največja dovoljena obremenitev: 36.500 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle stock, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Full specifications available upon request. * Gooseneck, approx. 4,100 mm long with central beam * Platform deck, extendable twice, approx. 9,400 mm in length * BPW axles and suspension * All axles hydro-mechanically forced steered * Technical axle load: 12,000 kg * Air suspension with lifting and lowering valve * Tires: 235/75 R 17.5 3PMSF dual mounted * WABCO brake system, EBS-E * 3 kW electro-hydraulic power unit for hydraulic operations, without installation of supply connections at the tractor unit * 4 pairs of stake pockets recessed into the outer frame of the gooseneck, for insertable stakes approx. 100 x 50 mm * 2-inch king pin * 8 pairs of stake pockets recessed into the outer frame of the platform deck, for insertable stakes approx. 100 x 50 mm * 1 lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the deck on the left in the direction of travel * Remote steering from the front and rear via cable remote control with push buttons; with single-track axle monitoring; no installation in the tractor unit * 2 axle load gauges mounted on the left side * Steel front wall, approx. 1,600 mm high * 3 transverse stake pocket strips in the platform deck, for insertable stakes approx. 100 x 50 mm * 1 transverse stake pocket strip in the gooseneck deck, for insertable stakes approx. 100 x 50 mm * 1 additional lockable INOX toolbox under the platform deck Ibjdowvzg Repfx Ai Ssb * WADER container pockets in the platform deck for transporting: 2x 20' containers or 1x 40' container * Central lubrication system with 2 pumps, brand BEKAMAX * Complete HRM metallization (High Resistance Metallisation)

Stanje: novo, največja dovoljena obremenitev: 38.370 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 960 mm, širina tovornega prostora: 254 mm, Leto izdelave: 2026, Proizvajalec: Faymonville Tip: Multimax Plus Leto izdelave: 2026 Vrsta izdelka: Novo Podatki: Gosji vrat, dolžina x širina: 3,70 x 2,48 m Ibedpfx Aezdmi Rji Sjb Tovornična površina, dolžina x širina: 9,60 x 2,54 m Število osi: 3 Nosilnost: 38.370 kg Lastna teža: +/- 11.130 kg Dovoljena skupna masa: 49.500 kg Oprema: BPW osi in vzmetenje, 1. in 2. os fiksni, 3. os vodilna. 3. os z elektro-magnetno blokado za vzvratno vožnjo, samodejno ob vzvratnem prestavljanju in ročno aktiviranje. Tehnična osna obremenitev: 12.000 kg. Nanesen peskani premaz na pokrivnih pločevinah gosjega vratu ter na prehodih med vratom in dvigovalnim ležiščem, med dvigovalnim ležiščem in tovorno površino ter med tovorno površino in rampami. 1 rezervno kolo z nosilcem pod tovorno površino desno pred osmi. Izrezi v zunanjem okviru tovorne površine in dvigovalnega ležišča za obešanje zateznih trakov (LC 2.000 daN). Dodatna oprema: električna vitla, cca 5.400 kg vlečne sile, z daljinskim upravljanjem. Jeklenica cca 24 m dolga, premer cca 9,5 mm, vključno z valjčkom za pritisk vrvi. Montaža vitla spredaj znotraj na gosjem vratu. 1 INOX zaščitna omarica za električno vitlo 5.400 kg, cca 825 x 340 x 390 mm (D x Š x V), ravna izvedba, z 1 pokrovom zgoraj in izrezom za kabel vitla. 1 INOX orodjarna, cca 620 x 300/180 x 950 mm (D x V x G), montirani levo in desno pod tovorno površino pred osmi, zadaj poševni. WABCO Smart Board sistem. Podatki o osni obremenitvi so veljavni le, ko je vozilo v nominalni višini vožnje, sicer so možna odstopanja. Smart Board ima števec prevoženih kilometrov. 1. os s pomočjo pri speljevanju. Razbremenitev zračnih blazin do 30 km/h in do 130% legalne osne obremenitve na preostalih oseh. Upravljanje preko zavornega pedala v vlečnem vozilu. Odlagalna površina za mostne elemente ramp pred osmi. Informacija: vzorčne slike Opomba: Lokacija: Essen, takoj na voljo.

Stanje: rabljeno, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, prva registracija: 09/2017, * SAF osi * Kolesni izrezi * Hidravlične nakladalne rampe, nastavljive po širini Ibodewta Aljpfx Ai Sob * Zračno vzmetenje * Možnost razširitve * Lastna teža: 11.020 kg ----Interna številka vozila: 11010----Napake in vmesna prodaja pridržane. WhatsApp podpora na voljo! Za vprašanja o vozilu ali dodatne informacije nam pišite udobno preko WhatsAppa WhatsApp nemško, angleško -- WhatsApp nemško, angleško, arabsko

Stanje: rabljeno, konfiguracija osi: 3 osi, prva registracija: 12/1997, dolžina tovornega prostora: 16.800 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 850 mm, Leto izdelave: 1997, Oprema: ABS, FAYMONVILLE NIZKOPODNOŽJE / RAZTEGLJIVI / AVTOVLEKA / krmilne osi / vitel - Isdpfx Aeybn Iwsi Sobb - MODEL: STN-3A DMC 38.000 KG LASTNA TEŽA 9.300 KG 3 OSI SAF OSI KRMLJENE OSI VITEL LISTNO VZMETENJE VIŠINA OD TAL 0,85 M VIŠINA DO BALKONA 1,35 M DOLŽINA ZLOŽENE PRIKOLICE 13,2 M DOLŽINA RAZTEGNJENE PRIKOLICE 16,8 M ŠIRINA NAKLADALNA: 2,55 M DOLŽINA BALKONA 4 M PNEVMATIKE: 235/75 R17.5 UVOŽENO NI BILO UPORABLJENO V DRŽAVI 100 % BREZ NESREČ - CENA NETO: 16.900 EUR - - CELOTNA PONUDBA NAŠEGA PODJETJA NA SPLETNI STRANI: MOŽNOST POŠILJANJA PODROBNIH FOTOGRAFIJ IN VIDEA NA WHATSAPP, VIBER ALI E-POŠTO ZA VEČ INFORMACIJ NAS KONTAKTIRAJTE TELEFONSKO. GOVORIMO NASLEDNJE JEZIKE: - Poljsko, angleško, nemško, romunsko, špansko, italijansko, francosko, turško, madžarsko, slovaško, slovensko, ruščino: - ukrajinsko, litovsko, latvijsko, estonsko, uzbeško, gruzijsko, armensko, azerbajdžansko, turkmenistansko, češko: -

Stanje: rabljeno, lastna masa: 14.100 kg, največja dovoljena obremenitev: 33.900 kg, skupna masa: 48.000 kg, konfiguracija osi: > 3 osi, prva registracija: 11/1999, vzmetenje: zrak, velikost pnevmatike: 235/75 17,5, stanje pnevmatik: 50 odstotek, barva: zelen, Leto izdelave: 1999, velikost sprednje pnevmatike: 235/75 17,5, velikost zadnje pnevmatike: 235/75 17,5, voznikova kabina: dnevna kabina, emisijski razred: noben, Oprema: registracija tovornjaka, Reference number for inquiries: 68574 Faymonville, Platform trailer * Year of manufacture: 1999 * Air suspension * Steering axle * Forced steering axle * Air supply coupling heads (red + yellow) * Connection plug: 2x 7-pin * Lifting and lowering device * Telescopic – extendable semi-trailer * Suspension: air * Gross vehicle weight: 48,000 kg * Unladen weight: 14,100 kg * Payload: 33,900 kg * Permissible total weight: 48,000 kg * Axle manufacturer: SAF * Tire condition 1st axle: 50% -- 50% - Tire size: 235/75 R17.5 * Tire condition 2nd axle: 50% -- 50% - Tire size: 235/75 R17.5 * Tire condition 3rd axle: 50% -- 50% - Tire size: 235/75 R17.5 * Tire sizes: 235/75 R17.5 * Superstructure manufacturer: ES-GE * Extension defective * Steering axles inoperative * Mobile/rollable Ijdpfxjyib Aho Ai Sjbb Liability disclaimer: Subject to alterations, prior sale, and errors excepted. Find more photos and videos on our homepage. Our comprehensive service includes, for example: * Purchase / sale / rental of commercial vehicles * Fast, uncomplicated financing solutions * Handling of all (export) documentation * Ordering export or customs license plates * Vehicle preparation: new tarpaulins, signage, painting, etc. * Professional loading and load securing * TÜV inspections and registration service * Transport of commercial vehicles Please contact our trained specialist staff—we are happy to assist you.

Stanje: novo, največja dovoljena obremenitev: 96.500 kg, skupna masa: 126.000 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 26.900 mm, skupna širina: 2.750 mm, Oprema: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: * Hydraulically lift/lowerable and detachable gooseneck, approx. 3,650 mm long * For tractor units: 6x4 or 8x4 * Truck hydraulic connection with flow control (20 l/min), incl. gantry for supply line suspension; the tractor unit tank must have at least 80 l capacity * With MAX Trailer coupling units; otherwise, coupling units to be provided ex works by the customer * Gantry with winch for spare wheel mounted at the front of the gooseneck * 3.5-inch king pin * Steel front wall approx. 400 mm high * Removable aluminium side and rear boards on the gooseneck, approx. 400 mm high, anodised finish * Control lever on the gooseneck protected by a folding cover * Operator area lighting at gooseneck, with on/off switch * One 7-pin socket each at the left and right rear of the gooseneck for warning sign * BEKA-MAX central lubrication system for one gooseneck with standard NLGI-2 grease * Hydraulic connections from the gooseneck to the low-bed via screw couplings * Access steps on the gooseneck * Four warning panels extendable by approx. 1,000 mm (approx. 423 x 423 mm) each, with one LED position lamp and bracket for beacon * Mounting adapters for 2 spare wheels * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery. Output: 9.5 kW (12.9 hp) at 3,000 rpm * Hydraulic connecting lines between powerpack and connector plate at the gooseneck * One LED worklight left and right on the rear plate of the gooseneck, individually switchable * Radio remote control for: - Operating the powerpack, start/stop of diesel engine. - Operating remote steering (in addition to cable remote), with 2 LED indicator lights on receiver for single-track control. - Lift/lower gooseneck. - Lift/lower suspension of running gear 2-axle front module: * Bolt-eye coupling front and rear. Length: approx. 2,970 mm. Module width: approx. 2,750 mm * BEKA-MAX central lubrication system for 2-axle module with standard NLGI-2 grease (not connected to steering rods) * One 7-pin socket each at the left and right rear of the front module for warning signs * Platform surface with sand coating as slip protection * Yellow reflective tape in accordance with EU regulations at the sides, on the extension, and at the rear of the trailer * One 7-pin socket for warning signs, left and right on the front module, in the axle area * Extendable outriggers approx. 230 mm per side for the 2-axle module * 1 pair M42 threaded blocks between the axles of the front module * 1 pair brackets for plug-in warning panels in the stake pockets of the exterior frame of the loading area Loading platform: * 6-axle, double telescopic loading platform with bolt-eye coupling at the front and rear chamfer approx. 500 mm x 8° * Platform length: approx. 11,000 mm * Technically extendable by: approx. 8,200 + 7,700 mm * Axle spacing: approx. 1,500 mm * Base width: approx. 2,750 mm * Hydraulic coupling pin * BEKA-MAX central lubrication system for the platform with standard NLGI-2 grease * Platform surface with sand coating as slip protection * 11 pairs of recessed lashing rings in the external frame of the loading platform, foldable outwards (LC 10,000 daN) Ibjdpjzahp Ssfx Ai Sjb * Permanently welded intermediate table, approx. 500 mm long * 1 pa...

Stanje: novo, največja dovoljena obremenitev: 42.900 kg, skupna masa: 55.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 29.000 mm, skupna širina: 2.540 mm, Oprema: ABS, The complete inventory of vehicles, including those available for immediate and short-term delivery, can be found on our website. Extract from the equipment list. Full specifications available upon request. Loading Platform: * Gooseneck, length approx. 3,900 mm with central beam * Loading platform, double extendable, length approx. 9,300 mm * A support plate, approx. 200 mm wide, is permanently welded to the central beam * Pneumatic locking system with conical locking pin and reinforced locking positions; supply lines are protected within the extendable beams and automatically adjust to the current platform length (except for the supply of the first and second locking positions) * Technical fifth wheel load: 25,000 kg Suitable for tractor units: 4 x 2, 6 x 2, and 6 x 4 * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, all axles hydro-mechanically forced steered, mounted on turntables * Technical axle load: 12,000 kg each, air suspension with lift and lower valve * 275/70 R 22.5 3PMSF twin tires. Brand at our discretion * ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for operating hydraulic functions * 3 pairs of recessed lashing rings in the outer frame of the gooseneck, foldable to the outside * 1 pair of lashing rings at the king pin (LC 10,000 daN) – all other lashing rings (LC 5,000 daN) * 3 pairs of stake pockets recessed in the outer frame of the gooseneck for plug-in stakes approx. 100 x 50 mm * 1 stake pocket bar mounted transversely on the gooseneck floor for plug-in stakes approx. 100 x 50 mm * 1x at the rear of the gooseneck * 2" king pin * Mechanical landing gear with 2-speed gearbox and crank * 8 pairs of stake pockets recessed in the outer frame of the loading platform for plug-in stakes approx. 100 x 50 mm Isdpfeyvnd Nsx Ai Sjbb * 10 pairs of recessed lashing rings in the outer frame of the loading platform, foldable to the outside * Remote steering from the front and rear via cable remote control, with axle tracking control, no installation required in the tractor unit * Last axle with air bellows venting activated when parking brake is applied * Steel front wall, approx. 1,600 mm high, certified design according to EN12642:2016 XL * Round NATO socket at the front connection bar (Maeler & Kaege VG 96 917) * 1 LED work light on each side at the landing gear, wired to the tractor unit connection bar * Approx. 32 mm wooden floor on the gooseneck and the loading platform * On the large-section extension tube, one locking position every approx. 500 mm * On the small-section extension tube, one locking position every approx. 1,000 mm, enabling locking at every approx. 500 mm * Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,500 daN) * 4 stake pocket bars mounted transversely on the loading platform floor for plug-in stakes approx. 100 x 50 mm * 4 wheel chocks with holder mounted under the loading platform * 1 lockable INOX toolbox, approx. 2,390 x 800 x 500 mm (L x W x H), mounted under the loading platform on the left in the direction of travel * 1 additional lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the loading platform on the right in the direction of travel * 1 LED work light each left and right in front of the axles, with wiring * 2 axle load gauges mounted on the left side including axle load diagram * 1st axle equipped with automatic lift axle function as well

Stanje: novo, največja dovoljena obremenitev: 30.190 kg, skupna masa: 43.000 kg, konfiguracija osi: 2 osi, Oprema: ABS, You can find our complete vehicle inventory, including vehicles available for immediate or short-term delivery, on our website. The following is an excerpt from the specifications. Complete equipment details available upon request. Load area: - Lowbed with external beams, extendable version in SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor, approx. 40 mm thick, with mechanical locking - Supply lines are protected within the extendable beams and automatically adjust to the current lowbed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for mounting bolted RUD rings Gooseneck: - Gooseneck in SNT design to optimize load area length, approx. 3,750 mm - Gooseneck hydraulically lift/lowerable and detachable Iedpfx Aoxarl Nsi Sebb - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2 Rear chassis: - Rear chassis in short version with closed outer frame and checker plate cover - Chassis with excavator recess, closed in the rear half to accommodate air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings lying flat, at the front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced-steered - Technical axle load: 12,000 kg per axle - Air suspension with raise/lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF, manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system according to ECE R 141 - Data transmission to tractor via standardized EBS interface (ISO 11992) - For proper display, the tractor must be capable of transmitting and displaying these data Braking system: - Braking system according to EU regulations with EBS-E (2S2M) Electrical system: - Electrical system in accordance with EU regulations, 24-volt lighting ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with turn indicator - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: - Steel construction of high-strength fine-grain steels - Steel qualities: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Entire steel construction automatically shot-blasted after welding - Second blasting with corundum for optimal coating adhesion - Complete vehicle chassis coated with HRM metallization using ZINACOR 850 (85% zinc / 15% aluminium) for premium corrosion protection - Top coat with 2 layers of 2K paint in RAL 3002 carmine red, single-color, according to RAL system 841GL - Rims in silver - Rear section metallized and painted in RAL 9010 (pure white) - No metallic paint possible - Paint system tested in salt spray test according to ISO 9227-NSS - Cavity sealing with special wax Including the following additional equipment: - 2-inch kingpin - One galvanized steel front wall, approx. 400 mm high - Remote-steered axles from front and rear via cable control with pushbuttons, with single-track monitoring (without installation in tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupler instead of threaded couplings - Electro-hydraulic power unit - Prepared for installation of bolted container mounts for 1x 20' or 1x 40' container on outer beams - Without container locks

Stanje: novo, največja dovoljena obremenitev: 36.040 kg, skupna masa: 53.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete inventory of immediately and short-term available vehicles can be found on our website. Excerpt from the equipment list. Full specification available on request. Gooseneck: * Gooseneck in SNT design to optimize loading deck length, approx. 3,750 mm long * Gooseneck hydraulically liftable/lowerable and detachable * For tractor units: 6 x 4 or 8 x 4 Lowbed: * Lowbed with exterior beams, extendable, SUPER LOW design, approx. 8,000 mm long * Lowbed with fixed hardwood flooring approx. 40 mm thick and mechanical locking * Supply lines routed protected within the extendable beams, automatically adapting to the lowbed length * 7 pairs of folding lashing rings outward (LC 10,000 daN) * 6 pairs of threaded mounting blocks on the inner beam for screwable RUD rings Rear chassis: Ibjdpfoy Uwu Isx Ai Sjb * Rear chassis with closed outer frame and tread plate cover * Chassis with excavator recess, closed in the rear half to house air tanks * 3 pairs of folding lashing rings outward (LC 5,000 daN) * 1 pair of folding lashing rings outward (LC 10,000 daN) * 1 pair of horizontal lashing rings, positioned front & rear on the chassis (LC 10,000 daN) Axles: * BPW axles and suspension, all axles with hydro-mechanical forced steering * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tyres: * Tyres 245/70 R 17.5 3PMSF – manufacturer at choice. Load index (146/146F) Braking system: * WABCO braking system according to EU regulations with EBS-E (2S2M) Coating: * HRM metalizing of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure optimal corrosion protection * Finished with 2 coats of 2K paint, single-colored in RAL 3002 Carmine Red, per RAL System 841GL Includes accessories: * 2-inch kingpin * One galvanized steel front bulkhead, approx. 400 mm high * At the galvanized front connection strip, yellow-red air couplings * Remote axle steering, from front and rear, operated by cable remote control with push buttons, including axle alignment monitoring (without installation on the tractor unit) * Preparation for bolt-on container lockings to accommodate 1 x 20', 1 x 40', or 1 x 45' container on the outer rails. Without container locks * Hydraulic connections from gooseneck to lowbed with a multicoupling instead of screw couplings * Electrohydraulic unit * Spiral cable (approx. 35 mm², approx. 3.5 m in length, max. 250A) for the power supply to the electrohydraulic unit and/or the electric winch, with plug connection (NATO-NATO) between trailer and tractor unit * Yellow reflective tape according to EU regulations, on the sides, extension, and at the rear of the trailer * At the gooseneck front and rear left and right, each with a holder for warning signs, including socket * Manual and documentation on USB stick * Central lubrication system with 2 pumps BEKAMAX (Pico) with standard grease NLGI-2 and removable protection for the pumps * 7 pairs of threaded blocks between the lashing rings under the top flange on the outer rail for mounting screwable RUD rings VLBG-4 * 2nd ride height, approx. 50 mm above standard ride position, selectable via manual control * On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm (L x H). The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) * Separate air connection with air gun on the gooseneck * A stainless steel toolbox, INOX, approx. 1,350 x 400 x 400 mm

Stanje: zelo dobro (rabljeno), konfiguracija osi: > 3 osi, dovoljena osna obremenitev (os 1): 10.000 kg, dovoljena osna obremenitev (os 2): 10.000 kg, dovoljena osna obremenitev (os 3): 10.000 kg, prva registracija: 03/2003, dolžina tovornega prostora: 12.500 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 1.620 mm, skupna dolžina: 12.500 mm, skupna širina: 2.550 mm, skupna višina: 1.620 mm, vzmetenje: hidravlika, velikost pnevmatike: 275 / 70 R22.5, barva: bež, Leto izdelave: 2003, Konfiguracija osi Dimenzija pnevmatik: 275 / 70 R22.5 Znamka osi: SAF Ibedpfeuu E S Sox Ai Sob Vzmetenje: hidravlično vzmetenje Zadnja os 1: Dvojna montaža; dvigljiva os; največja obremenitev osi: 10.000 kg; krmiljena Zadnja os 2: Dvojna montaža; največja obremenitev osi: 10.000 kg Zadnja os 3: Dvojna montaža; največja obremenitev osi: 10.000 kg; krmiljena Zadnja os 4: Dvojna montaža; največja obremenitev osi: 10.000 kg; krmiljena Zadnja os 5: Dvojna montaža; največja obremenitev osi: 10.000 kg; krmiljena Teže Lastna masa: 13.100 kg Nosilnost: 61.900 kg Dovoljena skupna masa: 75.000 kg Funkcionalno Višina nakladalne površine: 162 cm Stanje Tehnično stanje: zelo dobro Vizualno stanje: zelo dobro Finančne informacije Cena: na zahtevo

Stanje: novo, lastna masa: 14.350 kg, največja dovoljena obremenitev: 53.450 kg, skupna masa: 67.800 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, dvižna zadnja plošča, Gooseneck: - Gooseneck in SNT design for optimization of loading bed length, length approx. 3,700 mm - Gooseneck rear with chamfer approx. 1,000 mm x 10° - For tractor units: 6x2, 6x4, 8x4 short Loading bed: - Extendable loading bed, length approx. 8,800 mm, rear chamfer approx. 500 mm x 10° - A recess in the loading bed and the chamfered section for receiving the excavator dipper stick, approx. 3,850 x 750 x 210/290 mm Ibsdpfx Aeya E A Nji Ssb Two-part steel ramps: - One pair of two-part steel ramps, length approx. 4,350 mm, width approx. 900 mm - Ramps with rubber covering - Ramps hydraulically adjustable individually approx. 235 mm outwards and approx. 215 mm inwards - 'Super Grip' 25 mm rubber flooring and approx. 5 mm steel plate as additional reinforcement on the rear chamfer of the loading bed - Square climbing bars 20 x 30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: - BPW axles and suspension, 1st axle steering, all other axles hydromechanically forced-steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Tires 235/75 R 17.5 - TPMS tire monitoring system according to ECE R141 - TPMS tire sensors fitted on all wheels, including spares Surface treatment: - Complete steel structure automatically blasted with shot blasting system after welding - Second blasting with corundum for optimum coating adhesion - HRM metallization of entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for best corrosion protection - Final painting with 2 layers of 2K top coat, single colour in MB 7350 Novagrau Accessories included: - Plug-in steel front wall, approx. 400 mm high - 3kW electro-hydraulic power unit for controlling hydraulic functions, with the exception of hydraulic winches - 1 spare wheel - Outer carrier on the gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings in the rear area of the gooseneck - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized - On the gooseneck, 1 plug-in ALU rear board, approx. 400 mm high, anodized - On top of the gooseneck, approx. 40 mm thick hardwood flooring, above kingpin area with checker plate cover - 2" kingpin - Round NATO socket on front connection strip - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front cross member - 8 pairs of recessed, fold-out lashing rings in the outer frame of the loading bed - Extendable (galvanized) widenings by approx. 230 mm per side - Wheel recesses with square climbing bars, 15 x 15 mm, in front of the axles fully open up to gooseneck cross beam, approx. 700 x 410 mm - Wheel recesses with square climbing bars, 15 x 15 mm, between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - ALU covers for wheel recesses, which can also be used as bridging elements for the extension or as widening boards - 1 pair mechanical rear supports - Radio and cable remote control - Lift axle on front axle - Square climbing bars 20 x 30 mm, approx. every 200 mm - Central lubrication system with 1 pump - Wabco Smart Board system - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, lastna masa: 12.300 kg, največja dovoljena obremenitev: 37.200 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear chamfer of approx. 750 mm x 10° - 30 mm thick hardwood flooring Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system Gooseneck: - Gooseneck with rear chamfer of approx. 750 mm x 10° - 3 pairs of lashing rings - 30 mm thick hardwood flooring Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface Ibodpfstvfkfox Ai Seb - Ramps with hydraulically foldable ramp sections and hydraulic lifting system - Maximum load capacity per pair: 30,000 kg Loading area: - Loading area with rear chamfer of approx. 1,000 mm x 8° - Hardwood flooring approx. 48 mm thick, chequer plate flooring above the axles Axles and tires: - BPW axles and suspension, two rigid axles, one self-steering trailing axle - Air suspension with lift and lower valve - The trailing steering axle with electro-magnetic reversing lock, activated by reverse gear or manually - Tyres 235/75 R17.5 3PMSF Included accessories: - 1 spare wheel with holder - TPMS tyre pressure monitoring system according to ECE R 141 - 2" kingpin - One galvanized steel front wall - Yellow-red air couplings on the galvanized front connection rail - 4 chocks with holder on the front wall - Rear mounting area on the gooseneck for ALU approach ramps - 3 heights of aluminium planks - Galvanized folding supports under the loading area chamfer - Height-adjustable tarpaulin body (3,960 mm) - Galvanized front wall with tensioning mechanism for sliding curtain - Height adjustable by approx. 400 mm - "EDSCHA" brand roof, forward-sliding on ALU roof beam profiles, bolted to front and rear walls - 3 pairs of movable stakes in the loading platform - The superstructure is hydraulically extendable at the rear to the left and right by approx. 750 mm - Sliding roof with high-swivelling portal beam - Sliding curtain with 700 mm length surplus, with tensioning straps spaced approx. 600 mm apart - Height to top of the body: approx. 3,960 mm - Driving with open sliding roof is not permitted and will damage the curtain - Cover plates to bridge the gap between ramps and loading area - Rear electro-hydraulic unit under the loading platform - On gooseneck and ramps, each side with one holder for warning signs including socket - Ramp control valves located on right-hand side of trailer - 6 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading area - Lift axle on the front axle - Grating surface in the chamfer of the loading area C40/4 (point load 3.4 t on an area of 20 x 20 cm) - One INOX toolbox 565 x 290 x 810 mm, mounted on the right side in the direction of travel between the axles - Painted sand layer as anti-slip protection on the chequer plates on the gooseneck and loading area - BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable cover for the pump - Four extendable warning signs (approx. 400 mm each) approx. 423 x 423 mm with position light - Axle load gauge including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Entire steel structure shot-blasted, afterwards defined visible surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) hot-refined

Stanje: novo, lastna masa: 10.300 kg, največja dovoljena obremenitev: 39.200 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Platform: - Loading platform after the gooseneck, hydraulically liftable and lowerable, length approx. 2,800 mm, with rear chamfer approx. 1,000 mm x 8° - Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, over the axles with chequer plate covering Two-part Steel Ramps: - One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp parts, hydraulic lifting system, and hydraulically adjustable - Maximum load per pair: 40,000 kg Axles, Suspension and Tires: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated by reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tires 235/75 R 17.5 3PMSF - TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories Included: - One spare wheel with holder in front of the bulkhead - 2" kingpin - One galvanized steel front wall approx. 400 mm high - Yellow-red air couplings at the galvanized connection strip in front - 4 wheel chocks - Galvanized folding supports under the platform's rear chamfer - A holder for a rotating beacon at the rear of the trailer - Cover plates to bridge the gap between ramps and platform - White reflective tape as per EU regulations along the sides of the trailer and red at the rear - Electro-hydraulic unit at the rear, under the platform - At the gooseneck and at the ramps left and right, each with a holder for warning signs, including socket - Control valves for the ramps positioned on the right side of the trailer - European reflective plates (red-yellow) at the rear of the trailer - Manual and description on USB stick - Removable ALU side walls and rear wall on the gooseneck approx. 2,440 x 400 mm - The rear, galvanized side stakes are removable (body length approx. 2,560 mm) - An electric cable winch with radio remote control, approx. 5,400 kg lifting force, including 9.5 mm steel cable, 24 m long, with guide roller - Bolted 5 t ring for cable deflection of the winch on the gooseneck without pulley - 2 pairs WADER container pockets in the platform for a 20ft container - 6 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the platform - Lift axle on the front axle with control via TEBS E, depending on actual axle load and loading condition - 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN) - 1 pair of recessed lashing rings along the central beam at the rear chamfer (LC 10,000 daN) - Sand coating for slip resistance painted on the chequer plates on the gooseneck and on the platform Isdpfx Aieu Hp Hre Sebb - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and removable pump protection - Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm - Speed stickers 80 km/h rear and on both sides - Load manometer for determining axle loads including load chart - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then all defined visible surfaces metallized and hot-coated with ZINACOR 850 (zinc 85% - alu 15%)

Stanje: novo, največja dovoljena obremenitev: 90.700 kg, skupna masa: 126.000 kg, konfiguracija osi: > 3 osi, skupna širina: 2.850 mm, Oprema: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: Hydraulically lift/lower and detachable gooseneck. Length approx. 3,650 mm. Suitable for tractor units: 6x4 or 8x4 3-axle compact front bogie: * Hook mounts at front and rear. Length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Lowbed: * ATX-A lowbed with telescopic longitudinal beams in low-profile design, fixed hardwood floor approx. 50 mm thick * With drive-over bridge hooks at the front and bolt-lug coupling at the rear * Base width: approx. 2,850 mm, length: approx. 7,150 mm, beam height: approx. 330 mm, beam width: approx. 750 mm * Loading height approx. 480 mm, ground clearance approx. 150 mm 5-axle rear bogie: * Mechanical bolt-lug coupling for attaching a lowbed at the front; rear end traverse * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * Pendulum axle 3-axle front bogie: * PENDULUM AXLES, all axles hydro-mechanically forced-steered * Hose rupture valve on axle leveling cylinder with automatic RESET function * Hydraulic cylinders with shutoff taps and locking pins for securing in raised position * Final painting of axles with 2 coats of single color 2K paint, painted in MB7350 Novagrau * Rated axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tires for front bogie: 12 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J 5-axle rear bogie: * PENDULUM AXLES, all axles hydro-mechanically forced-steered * Hose rupture valve on axle leveling cylinder with automatic RESET function * Hydraulic cylinders with shutoff taps and locking pins for securing in raised position Ijdpsw Tgp Dsfx Ai Ssbb * Final painting of axles with 2 coats of single color 2K paint, painted in MB7350 Novagrau * Rated axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tires for rear bogie: 20 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimum corrosion protection * Final painting with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, according to RAL-System 841GL Including accessories: * Steel front wall, approx. 400 mm high * Plug-in aluminum side and rear boards on gooseneck, approx. 400 mm high, anodized * 3.5" kingpin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections on gooseneck * Front bogie with separate air connection for air impact wrench * BEKA-MAX central lubrication for one 3-axle bogie * Preparation for bolt-on container positioning for 1 x 20' or 1 x 30' on the outer beams * Without container locks * Brackets on the outer beams for installing foldable extensions * One 7-pin socket left and right, front and rear on rear bogie for warning panels * BEKA-MAX central lubrication for one 5-axle bogie * On the rear bogie, socket for cable remote control for steering * Rear bogie with trough * 2 LED reversing lights mounted on rear panel * European reflector boards (red-yellow) on the rear * One mudflap at rear * One LED beacon with bracket left and right on rear cross-member * Two INOX toolboxes 855 x 340 x 390 mm on gooseneck, left and right * 1-circuit...

Stanje: novo, največja dovoljena obremenitev: 25.645 kg, skupna masa: 38.000 kg, konfiguracija osi: 2 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Excerpt from the equipment list. Full equipment details available upon request. Loading Platform: - Low-bed with central beam in extendable design, length approx. 6,750 mm - 5 pairs of lashing rings, foldable outwards (LC 5,000 daN) - 1 pair of lashing rings, foldable outwards (LC 10,000 daN) - 1 pair of flush-mount lashing rings at the rear of the loading platform (LC 10,000 daN) Gooseneck: - Gooseneck hydraulically lift/lowerable and detachable Rear Running Gear: - Rear running gear in short version with closed outer frame and tread plate cover - Running gear with excavator trough, trough rear half enclosed for housing air tanks - 2 pairs of lashing rings, foldable outwards (LC 5,000 daN) - 1 pair of lashing rings, foldable outwards (LC 10,000 daN) - 1 pair of flush-mount lashing rings at the rear of the running gear (LC 10,000 daN) Axles: - BPW axles, hydromechanically forced steering - Air suspension with lifting and lowering valve Tyres: - Tyres 245/70 R 17.5 3PMSF - TPMS: tyre pressure monitoring system as per ECE R 141 Isdpfoxf Silox Ai Sobb Brake System: - Wabco braking system in compliance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality 2-component (2K) top coat, single colour RAL 3000 flame red Includes the following additional equipment: - 2 king pins - One galvanised steel front wall, approx. 400 mm high - Remote steering adjustment from front and rear via cable remote control with pushbuttons, including single-track axle alignment (without installation in the tractor unit) - Electro-hydraulic unit - Axle load gauge including axle load diagram - On the gooseneck, aluminium side boards and rear wall, plug-in type, approx. 2,440 x 400 mm (L x H). The rear galvanised plug-in stanchions are removable. (Upper body length approx. 2,560 mm) - Separate air connection with blow gun on the gooseneck - 2 work lights with switch on the trailer, mounted on left and right sides of the gooseneck platform - One INOX toolbox, approx. 1,350 x 400 x 400 mm, mounted on the gooseneck - 6 pairs of stanchion pockets for plug-in stanchions approx. 100 x 50 mm in the outer frame of the loading platform, 2 pairs in the rear frame of the running gear - Galvanised, extendable load width extensions approx. 230 mm per side - Hydraulic connections from the gooseneck to the low-bed with multi-coupling instead of screw couplings. No guarantee on seals. - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 with removable pump protection - 2 pairs of WADER container pockets in the loading platform, for 1x 20’ container - One removable galvanised intermediate platform with 1 pair of WADER container pockets - 1 pair of steel ramps to bridge over the low-bed’s loading hooks - Loading platform with painted sand layer as anti-slip protection - HRM metallization (High Resistance Metallization)

Stanje: novo, največja dovoljena obremenitev: 25.300 kg, skupna masa: 38.000 kg, konfiguracija osi: 2 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete range of vehicles, including those available for immediate and short-term delivery, can be found on our website. Excerpt from the equipment specification. Full specification available upon request. Gooseneck * Gooseneck in SNT design to optimize loading area length * Length approx. 3,750 mm, hydraulically lift-/lowerable, as well as detachable * Technical fifth-wheel load: 25,000 kg For tractors: 4 x 2 and 6 x 2 Kessel bridge * Low bed designed as telescopic Kessel bridge SUPER LOW design * Length approx. 6,850 mm * with mechanical locking * Supply lines are routed protectively within the telescopic beams and automatically adjust to the respective low bed length Rear chassis * Short version with closed outer frame and tread plate cover * Chassis with excavator recess, closed in the rear half to accommodate air tanks Axles * BPW axles and suspension, all axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve Tyres * GOODYEAR KMAX T 3PMSF (M+S) 245/70 R 17.5 twinned. Load index 143/141J (146/146F) Brake system * WABCO brand, EBS-E according to EU regulations, WITHOUT connection cable to tractor unit Paintwork * 6-coat final treatment * Complete steel construction shot-blasted after welding * 1 layer of zinc-based primer * 1 layer of adhesion primer. Final coating with 2 layers of 2K (acrylic) paint, single colour, then cavity sealing with special wax Trailer colour * RAL 3002 Carmine red * Rim colour: silver-grey * Side wall colour: Aluminium-natural Accessories included * Steel front wall, plug-in, approx. 400 mm high * 3 kW electro-hydraulic pump unit for hydraulic operation, except for hydraulic winches. Without installation of supply connectors at the tractor unit * Mounting adapter for 1 spare wheel in front of the gooseneck front wall * Outer beams of the gooseneck with mounting holes for screwable lashing rings. The first hole approx. 200 mm from the front, then approx. every 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 lashing ring each left and right on the rear chamfer of the gooseneck (LC 6,000 daN) * 2 inch kingpin * Hydraulic traverse for supporting the gooseneck on the tractor or a dolly * Air connection with air pistol on the gooseneck * 1 pair of steel ramps with climbing cleats and retaining bolts to bridge the low bed attachment hooks * 1 lashing ring each left and right on the front cross member (LC 10,000 daN) * At the outer beams of the loading area, prepared for removable loading floor * Lashing rings with retaining spring approx. every 1,200 - 1,300 mm on the inside outer beams of the loading area * Lashing rings with retaining spring approx. every 1,200 - 1,300 mm on the outermost beams of the loading area (LC 10,000 daN) Ibjdpfxov Sw E Ae Ai Sob * Cut-outs over the lashing rings on the upper flange of the outer beams * Mechanical pin-lug coupling from the low bed to the running gear, for changing the loading area or installing extension beams. With electro-pneumatic-hydraulic couplings * Outer beams of the low bed with painted-on sand layer for anti-slip protection * 2nd driving height for upper drive position, max. ± 50 mm from the normal driving position, without installation of controls from the tractor unit * 1 pair of lashing rings with retaining spring at the transition from low bed to excavator recess (LC 10,000 daN) * Front and rear chamfered edge

Stanje: novo, največja dovoljena obremenitev: 36.410 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete vehicle inventory, including vehicles available immediately or at short notice, can be found on our website. Excerpt from the equipment. Full equipment details available on request. GOOSENECK: * Gooseneck in SNT design to optimize load bed length, approx. 3,700 mm long, with rear taper approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Steel front bulkhead, removable, approx. 400 mm high Ijdpey Auh Ijfx Ai Ssbb * ASPÖCK-UNIBOX * 3 kW electric-hydraulic unit for hydraulic operations, excluding hydraulic winches * Approx. 40 mm thick hardwood cover above the gooseneck * 2-inch kingpin * Guide plate from the gooseneck for the fifth-wheel plate, approx. 500 mm wide * Receptacle at the rear of the gooseneck for aluminum drive-on ramps * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 4 wheel chocks with holders in front of the bulkhead * 1 pair of stake pockets embedded in the gooseneck, for plug-in stakes approx. 100 x 50 mm (inner chassis rail) EQUIPMENT: * Load bed approx. 8,800 mm long, extendable version approx. 4,100 mm, with rear taper approx. 500 mm x 10° * Recess in the load bed including the rear slope to accommodate the excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * Pneumatic locking with conical locking bolts and reinforced locking positions, with protected supply lines inside the extendable beams, automatically adapting to the respective load bed length * TPMS tire pressure monitoring system according to ECE R 141 * BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle steering-following * 3rd axle with electromagnetic reverse lock, activating via reverse gear or manually * Technical axle load: 12,000 kg each, air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires. Make at our discretion * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B - static test load = approx. 50,000 kg * Continuous and between-axle interrupted approx. 50 mm hardwood planking on load bed (increasing coefficient of friction) * 1 cross table, approx. 300 mm wide, for the extendable tube with large cross-section; cross table with offset load bed and extendable mounting rails for aluminum bridging elements * Load bed locking with conically welded locking profiles every approx. 250 mm, including pretensioning plate * 1 pair of lashing rings on front crossbeam (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the load bed, foldable outwards (LC 10,000 daN) * 1 pair of fixed wheel recesses in front of the axles, open up to the gooseneck crossbeam, approx. 700 x 410 mm (W x D) * Wheel recesses with approx. 15 x 15 mm square climbing strips and widened sections at the lower area (if vehicle is fitted with extendable widenings) * 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the load bed between 1st and 2nd axle * Wheel recesses with approx. 15 x 15 mm square climbing strips and widenings in lower area * Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axle, can also be used as widening planks (if vehicle is fitted with extendable widenings) * Aluminum elements lockable on the extension beams of the widenings * 1 pair of mechanical rear supports * 1st axle with traction aid * Sandblasted and painted in single color according to RAL code

Stanje: novo, največja dovoljena obremenitev: 47.300 kg, skupna masa: 58.000 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 8.600 mm, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment list. Complete equipment details available upon request. Gooseneck: * Gooseneck with chamfered front corners approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area in extendable design with rear chamfer approx. 1,000 mm x 8° * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN) * 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) * Recesses in the outer frame of the loading area for securing straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate flooring above the axles Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Tyres: * Tyres 235/75 R 17.5 3PMSF, manufacturer of our choice Axles: * BPW axles, two rigid axles, two self-tracking axles, air suspension, drum brake, with lifting/lowering function * The self-tracking axles can be locked for reversing by electro-magnetic reverse lock via reverse gear or manually * Axle tools Brake system: * WABCO brake system in compliance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system: * Electrical system in accordance with EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting * ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Premium and durable corrosion protection for the standard shot-blasted welded frame ensured by a two-component (2K) zinc dust primer * High-quality two-component (2K) topcoat, single colour, RAL 3002 Carmine Red * Rear section metallised and painted in RAL 9010 (Pure White) * Rims in silver Accessories: * Spare wheel holder in front of the front wall (without spare wheel) * 2-inch king pin * Galvanised steel front wall approx. 400 mm high * Yellow-red air couplings on the galvanised connection strip at the front * Mount in the rear area of the gooseneck for ALU loading ramps * Galvanised folding supports under the rear chamfer of the loading area * Holder for a beacon at the rear of the trailer * On the gooseneck and at the rear end panel, left and right, holders for warning signs including socket * TPMS tyre pressure monitoring system according to ECE R 141 Ibodpfjyvnfgox Ai Sjb * On the gooseneck, plug-in aluminium side walls and tailgate, approx. 2,440 x 400 mm (L x H). The rear galvanised plug-in stanchions are removable. (Body length approx. 2,560 mm) * Galvanised toolbox integrated into the chamfered gooseneck * 3 pairs of WADER container pockets recesses in the loading area for a 20' (30') or 40' container * Sliding hooks for aluminium loading ramps at the rear of the vehicle * 6 pairs of stanchion pockets for plug-in stanchions approx. 100 x 50 mm in the outer frame of the loading area * Galvanised extensions, extendable by approx. 230 mm per side * Lift axle on the front axle with control via TEBS E depending on the current axle load and current loading status * 2 LED reversing lights mounted on the rear end panel * 2 pairs Ferry-