Faymonville Standardna Struktura nakup rabljenega (185)

Stanje: novo, lastna masa: 6.350 kg, največja dovoljena obremenitev: 38.650 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22,5, Oprema: ABS, Loading Platform: - 2 pairs of folding external lashing rings (LC 5,000 daN) - 24 pairs of cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) Landing Legs: - JOST mechanical landing legs with 2-speed gearbox, 24 t lifting capacity (50 t test load) Axles and Tyres: - BPW axles, air suspended, with disc brakes (430 mm), lift/lower function - Tyres: 385/65 R 22.5 Braking System: - WABCO braking system compliant with EU regulations featuring EBS-E (2S2M) Paintwork: - Premium and durable corrosion protection of the standard grit-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) top coat in single-tone MB 7350 Novagrau - Rear section metallized and painted in RAL 9010 (pure white) - Metallic paintwork not possible Steel Construction: - Steel construction made from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical System: - Electrical system in accordance with EU regulations - Lighting: 24 volt - ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connection bar with 24N, 24S, and 15-pin sockets Gksdpfjiu Etkex Af Rjb - Connection standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Accessories included: - Yellow-red air couplings at the galvanized front connection bar - 4 wheel chocks with holders - 2" king pin - Galvanized steel front wall approx. 1,600 mm high, EN12642-XL - White reflector tape according to EU regulations, lateral and rear red - European reflective panels (red-yellow) at the rear of the trailer - Loading platform with approx. 30 mm thick hardwood flooring, framed in omega profiles - 10 pairs of stanchion sockets for 100 x 50 mm plug-in stakes in the outer frame - 3 pairs of transverse stanchion rack strips, fitted in the loading platform, for 100 x 50 mm plug-in stakes - Bracket for 1,000 mm plug-in stakes, rear in the central beam - 1 spare wheel carrier under the loading platform on the right hand side - 1 mudflap at the rear of the trailer - Manual and description on USB stick - Bracket for beacon at the rear of the trailer - Holders for warning signs including socket at the gooseneck and left/right rear panel - 6 pairs of WADER container locks on the loading platform for 1x 20ft, 2x 20ft, or 1x 40ft container, flush with rear - 80 km/h speed stickers at the rear and both sides - Four warning signs, extendable by approx. 400 mm, approx. 423 x 423 mm, with LED position light - Load gauge for axle load determination including load diagram - HRM (High Resistance Metallisation) of the outer frame - Complete steel structure is grit blasted, then defined visible surfaces are metallized with ZINACOR 850 (zinc 85% - aluminium 15%) by hot coating

Stanje: novo, skupna masa: 80.000 kg, konfiguracija osi: > 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Further vehicles available – excerpt from the equipment list. Full equipment details on request. GOOSENECK: * Gooseneck in SNT design for optimized loading bed length, length approx. 3,700 mm, rear with chamfer approx. 1,000 mm x 10° * For tractor units: 4x2, 6x2, and 6x4 * Front steel bulkhead, plug-in, approx. 400 mm high * ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for controlling hydraulic functions (excluding hydraulic winches) * Outer beams of the gooseneck with mounting holes for bolted lashing rings. First hole approx. 200 mm from the front, then approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair horizontal lashing rings at the rear section of the gooseneck (LC 10,000 daN) * On the gooseneck: 1 pair removable ALU side boards approx. 400 mm high, anodized finish * On the gooseneck: 1 removable ALU rear board approx. 400 mm high, anodized finish * Over the gooseneck: approx. 40 mm hardwood flooring, over the king pin checker plate covering * 3.5-inch king pin * Gooseneck guide plate for the fifth-wheel plate, approx. 500 mm wide * Round NATO socket at the front connection bar (Maeler & Kaege VG 96 917) * 2 pairs of suspended lashing rings with retaining spring on the outer beams of the gooseneck (LC 5,000 daN) LOADING BED: * Loading bed, extendable version, length approx. 8,800 mm with chamfer at the rear approx. 500 mm x 10° * Pneumatic locking with conical locking bolt and reinforced locking positions, supply lines are protected within the extendable beams and automatically adapt to the respective bed length * BPW axles and suspension, first axle hydraulically steered, all other axles hydro-mechanically forced steered * First axle with electro-magnetic reverse lock, activated by reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * 235/75 R 17.5 3PMSF twin tyres – manufacturer at our discretion * Mechanical landing legs with 2-speed gearbox and crank. JOST Modul B – static test load = 50,000 kg * Continuous hardwood flooring (approx. 50 mm thick) on the bed and between axles (interrupted), increasing friction coefficient. – Slots for attachable and adjustable bridging elements * At the front of the bed – 1 movable intermediate table approx. 300 mm wide for the large-section telescopic tube, with checker plate covering. – Front and rear slots for attachable and adjustable bridging elements * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 7 pairs of recessed folding lashing rings on the outer frame of the bed (LC 10,000 daN) * Extensions (galvanized), extendable by approx. 230 mm per side (without wooden planks) * 1 pair mechanical rear supports * Remote-controlled steering from front and rear via cable remote control, with single-track control of axles, without installation in the tractor unit Gjdpfx Aexarmasf Rjkb * TPMS tire pressure monitoring sensors installed in all wheels * Locking of the bed with conically welded retaining profiles every 500 mm * Locking control left and right on the trailer * For the intermediate table approx. 300 mm wide, a mechanical lock for securing the table in the extension * 5 pairs of threaded blocks on the extendable beam for mounting M20 screw rings (LC 5,000 daN) BRAKING SYSTEM

Stanje: novo, največja dovoljena obremenitev: 36.410 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete vehicle inventory, including vehicles available immediately or at short notice, can be found on our website. Excerpt from the equipment. Full equipment details available on request. GOOSENECK: * Gooseneck in SNT design to optimize load bed length, approx. 3,700 mm long, with rear taper approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Steel front bulkhead, removable, approx. 400 mm high * ASPÖCK-UNIBOX * 3 kW electric-hydraulic unit for hydraulic operations, excluding hydraulic winches * Approx. 40 mm thick hardwood cover above the gooseneck * 2-inch kingpin * Guide plate from the gooseneck for the fifth-wheel plate, approx. 500 mm wide * Receptacle at the rear of the gooseneck for aluminum drive-on ramps * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 4 wheel chocks with holders in front of the bulkhead * 1 pair of stake pockets embedded in the gooseneck, for plug-in stakes approx. 100 x 50 mm (inner chassis rail) EQUIPMENT: * Load bed approx. 8,800 mm long, extendable version approx. 4,100 mm, with rear taper approx. 500 mm x 10° * Recess in the load bed including the rear slope to accommodate the excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * Pneumatic locking with conical locking bolts and reinforced locking positions, with protected supply lines inside the extendable beams, automatically adapting to the respective load bed length * TPMS tire pressure monitoring system according to ECE R 141 * BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle steering-following * 3rd axle with electromagnetic reverse lock, activating via reverse gear or manually * Technical axle load: 12,000 kg each, air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires. Make at our discretion * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B - static test load = approx. 50,000 kg * Continuous and between-axle interrupted approx. 50 mm hardwood planking on load bed (increasing coefficient of friction) * 1 cross table, approx. 300 mm wide, for the extendable tube with large cross-section; cross table with offset load bed and extendable mounting rails for aluminum bridging elements * Load bed locking with conically welded locking profiles every approx. 250 mm, including pretensioning plate * 1 pair of lashing rings on front crossbeam (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the load bed, foldable outwards (LC 10,000 daN) * 1 pair of fixed wheel recesses in front of the axles, open up to the gooseneck crossbeam, approx. 700 x 410 mm (W x D) Gksdpfxoy Auh Ie Af Rsb * Wheel recesses with approx. 15 x 15 mm square climbing strips and widened sections at the lower area (if vehicle is fitted with extendable widenings) * 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the load bed between 1st and 2nd axle * Wheel recesses with approx. 15 x 15 mm square climbing strips and widenings in lower area * Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axle, can also be used as widening planks (if vehicle is fitted with extendable widenings) * Aluminum elements lockable on the extension beams of the widenings * 1 pair of mechanical rear supports * 1st axle with traction aid * Sandblasted and painted in single color according to RAL code

Stanje: novo, največja dovoljena obremenitev: 48.300 kg, skupna masa: 71.000 kg, konfiguracija osi: > 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete vehicle inventory, including vehicles available immediately and at short notice, can be found on our website. Below is an excerpt from the equipment list. Full specification available upon request. GOOSENECK: * Gooseneck with integrated single-axle running gear (pendulum axle) in a detachable version * Gooseneck hydraulically liftable and lowerable, including hydraulic connection linked to the hydraulic axle compensation of the first axles * Length: approx. 5,200 mm, with front tapering approx. 60° * Fifth wheel load according to data sheet: W25-DSR2700-12/22.7 * For tractor units: 6 x 4 or 8 x 4 * Steel front wall, plug-in type, approx. 400 mm high, with beveled design * 1 pair of mechanical supports at the front of the gooseneck * ASPÖCK-UNIBOX on the front connector panel with 24N, 24S & 15-pin sockets * 1 spare wheel holder inside the front wall of the gooseneck with jib * 2 pairs of recessed lashing rings on the gooseneck (LC 2,500 daN) * 2 pairs of recessed lashing rings on the outer frame of the running gear at the front, foldable outward (LC 10,000 daN) * 1 pair of lashing rings at the transition from running gear to loading platform (LC 10,600 daN) * On the gooseneck 1 pair of removable aluminum drop sides, approx. 400 mm high, anodized * On the gooseneck 1 removable aluminum rear wall, approx. 400 mm high, anodized * 3.5 inch kingpin * TPMS tire pressure monitoring system according to ECE R 141 * Round NATO socket on the front connector panel (Maeler & Kaege VG 96 917) * 1 stainless steel toolbox with 1 lid, mounted on the gooseneck on the right in the direction of travel by the aluminum drop side, approx. 1,350 x 400 x 400 mm (L x W x H) LOADING PLATFORM: * Low-bed with external beams, designed as a telescopic loading platform in low-profile design with front extension including fixed approx. 50 mm thick hardwood floor * Length x width approx. 8,000 mm x 2,740 mm * Mechanical bolt-lug coupling from low-bed to running gear for swapping the loading platform or installing extension beams * One locking position approx. every 500 mm on the extension * 4 pairs of recessed lashing rings fitted flat in the loading platform along the outer frame/external beams (LC 10,000 daN) * 1 lashing ring each on the left and right outer rear cross member (LC 10,000 daN) * Foldable extensions, approx. 230 mm per side (WITHOUT wooden boards) * Loose extension planks, steel-rimmed * Preparation for installation of bolted container positions for 1x 20’ or 1x 40’ container on the outer beams. Without container locks * 6 pairs of threaded blocks between the lashing rings under the top chord of the outer beam for mounting bolted M24 rings (LC 8,000 daN) Gjdjyhkqnopfx Af Rjkb * 2 pairs M24 bolt rings (LC 8,000 daN) included REAR RUNNING GEAR: * Rear running gear with closed outer frame, checker plate decking and continuous prism-shaped excavator trough, approx. 1,450 x 900 x 505 mm, open at the rear * PENDULUM AXLE, all axles hydro-mechanically forced-steered * Hose rupture valve on axle compensation cylinder with automatic reset function * Hydraulic cylinders with shut-off valves and foreplugs to secure in raised position * Final paint of axles in 2 layers of 2-component paint, single color, DB 7350 Novagrau * Technical axle load: 12,000 kg each * Hydraulic axle compensation * 245/70 R 17.5 3PMSF, brand at our choice * Remote steering from front and rear via cable control, with axle alignment check, no installation in the tractor unit * 4 pairs of hanging la

Stanje: novo, lastna masa: 9.600 kg, največja dovoljena obremenitev: 53.400 kg, skupna masa: 63.000 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 12.400 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.340 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22.5, barva: siv, Oprema: ABS, Platform area: - Platform with approx. 30 mm thick hardwood flooring - 10 pairs of folding lash rings (outward folding) Landing legs: - JOST landing legs with 2-speed gearbox, 24 t lifting capacity Axles and tyres: - BPW axles, technical capacity 10,000 kg per axle; first axle fixed, all other axles hydro-mechanically forced-steered, mounted on turntables Godpfxsrq Dlfe Af Rokb - Air suspension with raise/lower valve - Axle tools included - Tyres: 385/65 R22.5 Braking system: - WABCO brake system in accordance with EU regulations, with EBS-E (4S3M) Steel construction: - Steel structure made from high-tensile fine-grained steels - Steel grades: - S355J2+N / S355MC - S690QL / S700MC Electrical system: - Electrical system according to EU regulations, 24 Volt lighting - ASPÖCK-UNIBOX on the front connection rail with 24N, 24S and 15-pin sockets - Connections according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - First-class and durable corrosion protection of the standard shot-blasted welded frame is ensured by a 2-component zinc-dust primer - High-quality 2-component topcoat, single-colour in Nova Grey - Rear section metallized and painted in RAL 9010 Accessories included: - Platform with approx. 30 mm thick hardwood flooring - 2" king pin - One galvanized steel front wall approx. 1,200 mm high, EN12642-XL - Yellow-red air couplings at the galvanized connection rail at the front - 4 wheel chocks with holders on the front wall - Storage for 1,000 mm plug-in stanchions in the rear central beam - On the gooseneck and rear panel, left and right, a mounting bracket for warning signs with socket - Remote steering from front and rear, operated via cable remote control with push-buttons; with axle tracking control - Electro-hydraulic power pack - White reflective tape as per EU regulations along the side of the trailer, red at rear - 12 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the load bed - European reflective plates at the trailer rear - One bracket for a rotary beacon at the rear of the trailer - One mudflap at the trailer rear - Manual and documentation on USB stick - Central lubrication system BEKAMAX (Pico) with standard NLGI-2 grease and removable protector for the pump - TPMS tyre pressure monitoring system: - The towing vehicle must be capable of transmitting and displaying these data for correct readout - Lift axle on the front axle, automatically controlled by TEBS E in accordance with current axle load and trailer loading status - Radio remote control for the remote steering in addition to the cable remote, with indicator lamps on the receiver for axle tracking control - 5 pairs of crosswise stanchion pocket strips on the bed for 100 x 50 mm plug-in stanchions - 80 km/h speed stickers at rear and both sides - Adjustable access ladder mounted left and right in direction of travel - 2 reversing lights mounted at the rear panel - Load gauge for determining axle loads, including load diagram - HRM metallization of the outer frame: complete steel structure shot-blasted, then all designated visible areas hot metalized with ZINACOR 850 (Zinc 85% - Aluminum 15%)

Stanje: novo, lastna masa: 9.450 kg, največja dovoljena obremenitev: 35.550 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.500 mm, širina tovornega prostora: 1.560 mm, skupna širina: 2.550 mm, velikost pnevmatike: 385/65 R 22,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck designed as a loading platform with aluminum chequer plate covering - Front chamfered approx. 45° - Hydraulic lifting arm, lifting and lowering range approx. -280/+250 mm - Two king pin positions at DSR 2,300 and 2,000 mm - Compatible with tractor units: 4x2, 6x2, or 6x4 Loading Bay: - Loading bay, length approx. 9,500 mm, fitted with angle profiles at the bottom for pallet accommodation (distance from king pin to center of axle assembly approx. 8,000 mm) Axles, Suspension, and Tires: - BPW axle stubs with drum brakes and independent wheel suspension, hydraulic axle leveling with lifting and lowering function - Lowering lock on axles in case of suspension hose rupture, designed for maximum pallet height of 150 mm - Tires: 385/65 R 22.5 - TPMS tire pressure monitoring sensors installed in all wheels including spare wheels - TPMS system in accordance with ECE R 141 Surface Treatment: - Complete steel structure, shot-blasted automatically after welding Gjdpeygvc Hofx Af Rjkb - Second blasting with corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for maximum corrosion protection - Final coating with two layers of 2K topcoat, single-color in Novagrau (DB 7350) - Paint system tested with salt spray test according to ISO 9227-NSS; cavity sealing with special wax Included Accessories: - Steel front wall, plug-in, approx. 400 mm high - Toolbox with lid, integrated in the rear area of the gooseneck, approx. 640 x 700 x 215 mm - Plug-in ALU rear wall on the gooseneck, approx. 400 mm high, anodized - 1 pair of foldable ALU side boards on the gooseneck, approx. 400 mm high, anodized - 2" king pin - 3 pairs of recessed lashing rings on the gooseneck (LC 6,300 daN) - Front connector strip with yellow-red air couplings; illuminated operation for gooseneck, suspension, and hydraulic bracing, with on/off switch - Mechanical drop-leg supports for approx. 48,000 kg support load - Access ladder mounted front right, with 2 plug-in handrails - WABCO Roll Stability Support (RSS) - On the longitudinal beams, 9 pairs of lashing rings (LC 6,300 daN) - On the longitudinal beams, a grating platform level with the load securing rails - Hydraulic preinstallation including control unit for installation of 3 pairs of our hydraulic load restraints - First and last axle, left and right, manually liftable - Storage box behind axle assembly, left and right, splash-water protected - Rear chamfer for easier pallet insertion - Eyes on the rear crossmember for mechanical bracing - 7-pin socket on rear crossmember - Electro-hydraulic unit - 4 wheel chocks with holders - 2 axle load gauges mounted on the left side including axle load chart - 3 pairs of hydraulic load restraints with swivel arm, adjustable on the longitudinal beams - Rear door with cross bracing, hinged left and hydraulically locked right, horizontally lockable at 90°, 105°, and 270° - Folding underrun protection for transporting up to 4 empty standard pallets - 1 spare wheel - License plate bracket with lighting, rear left on trailer - Round NATO socket on the front connector strip (Maeler & Kaege VG 96 917) - Central lubrication system with 1 pump, BEKAMAX brand, standard grease execution

Stanje: novo, največja dovoljena obremenitev: 30.190 kg, skupna masa: 43.000 kg, konfiguracija osi: 2 osi, Oprema: ABS, You can find our complete vehicle inventory, including vehicles available for immediate or short-term delivery, on our website. The following is an excerpt from the specifications. Complete equipment details available upon request. Load area: - Lowbed with external beams, extendable version in SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor, approx. 40 mm thick, with mechanical locking - Supply lines are protected within the extendable beams and automatically adjust to the current lowbed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for mounting bolted RUD rings Gooseneck: - Gooseneck in SNT design to optimize load area length, approx. 3,750 mm - Gooseneck hydraulically lift/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2 Rear chassis: - Rear chassis in short version with closed outer frame and checker plate cover - Chassis with excavator recess, closed in the rear half to accommodate air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings lying flat, at the front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced-steered - Technical axle load: 12,000 kg per axle - Air suspension with raise/lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF, manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system according to ECE R 141 - Data transmission to tractor via standardized EBS interface (ISO 11992) - For proper display, the tractor must be capable of transmitting and displaying these data Braking system: - Braking system according to EU regulations with EBS-E (2S2M) Electrical system: - Electrical system in accordance with EU regulations, 24-volt lighting ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with turn indicator - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: - Steel construction of high-strength fine-grain steels - Steel qualities: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Entire steel construction automatically shot-blasted after welding - Second blasting with corundum for optimal coating adhesion - Complete vehicle chassis coated with HRM metallization using ZINACOR 850 (85% zinc / 15% aluminium) for premium corrosion protection - Top coat with 2 layers of 2K paint in RAL 3002 carmine red, single-color, according to RAL system 841GL - Rims in silver - Rear section metallized and painted in RAL 9010 (pure white) - No metallic paint possible - Paint system tested in salt spray test according to ISO 9227-NSS - Cavity sealing with special wax Including the following additional equipment: - 2-inch kingpin Gkedjxarl Njpfx Af Rob - One galvanized steel front wall, approx. 400 mm high - Remote-steered axles from front and rear via cable control with pushbuttons, with single-track monitoring (without installation in tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupler instead of threaded couplings - Electro-hydraulic power unit - Prepared for installation of bolted container mounts for 1x 20' or 1x 40' container on outer beams - Without container locks

Stanje: rabljeno, barva: rumena, Leto izdelave: 2013, Faymonville STZ-3UB. Leto: 2013. 10-tonske osi SAF. Teža: 12.300 kg. Nosilnost: 29.700 kg. Maksimalna teža: 42.000 kg. Obremenitev pete: 18.000 kg. Servovolk z 3 krmilnimi osmi. Razcepljena talna površina. Gkedpfszyaxksx Af Rob Vinska. Aluminijaste plošče na sprednjem delu. Hidravlični sistem prikolice, združljiv z NATO. Radijski daljinski upravljalnik. Zračna vzmet. Hidravlični most od talne površine do sprednjega dela. Dolžina: 3000 mm. 2 točki hidravličnih opornikov na zadnji strani. 2-smerne hidravlične rampe: Dolžina: 2800 + 1700 mm. Dimenzije: Sprednji del: D: 3750 mm. Š: 2500 mm. V: 1380 mm. Višina pete: 1150 mm. Talna površina: D: 9600 mm. Š: 2550 mm. V: 900 mm. Pnevmatike: 245/70R17,5, 80 %. ID št: 676. Splošni pogoji poslovanja podjetja Heinhuis veljajo za vse oglase, ponudbe in cenitve podjetja Heinhuis, za vse pogodbe, sklenjene s podjetjem Heinhuis, in za pogajanja, ki jim predhodijo. S kakršnim koli odgovorom potrdite veljavnost splošnih pogojev poslovanja podjetja Heinhuis in izjavljate, da ste se z njimi seznanili. Naše cene so izvozne neto cene. = Dodatne informacije = Leto izdelave: 2013 Lastna teža: 12.300 kg Nosilnost: 29.700 kg Maksimalna dovoljena masa: 42.000 kg = Informacije o podjetju = Za več informacij:

Stanje: novo, lastna masa: 29.600 kg, največja dovoljena obremenitev: 72.400 kg, skupna masa: 102.000 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 6.650 mm, širina tovornega prostora: 2.840 mm, višina nakladalnega prostora: 550 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, obratovalna teža: 29.600 kg, Oprema: ABS, Gooseneck: - Gooseneck hydraulically liftable/lowerable and detachable - Length approx. 3,650 mm - For tractor units: 6 x 4 or 8 x 4 2-axle front bogie: - Hook mountings at front and rear - Bogie length x width approx. 2,200 mm x 2,850 mm Excavator deck "BB-A": - Telescopic excavator deck "BB-A" with drive-over bridge hooks at the front and pin-lug coupling at the rear - Length x base width approx. 6,650 mm x 2,850 mm - Beam height x beam width approx. 400 mm x 1,350 mm - Loading height 550 mm with 150 mm ground clearance 4-axle rear bogie: - Mechanical pin-lug coupling for the installation of a lowbed at the front, rear crossmember at the back - Bogie length x width approx. 5,480 mm x 2,850 mm - Multiple lashing points Pendulum axles and tyres (front and rear bogies): - "PENDULUM AXLE", all axles forced-steered via hydromechanics - Hose rupture valve on axle compensation cylinders with automatic RESET function - Hydraulic cylinders with shut-off valves and locking clips for securing in raised position - Final coating on axles: 2 layers of single-colour MB 7350 Novagrau 2K paint - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres size 285/70 R19.5 Remote steering (after-steering): - Remote steering operable from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Socket for remote steering control on gooseneck - Cable remote control with pushbuttons and single-track control included Accessories included: - Yellow and red air couplings on the galvanised front connection bar - Steel front wall approx. 400 mm high - 4 wheel chocks - 3.5" king pin - One 7-pin socket left and right at rear of gooseneck for warning boards - Hoisting jib with winch for spare wheel at the front face of the gooseneck - Truck hydraulic connection with flow control (40 l/min), including support jib for supply lines; tractor unit tank must have at least 80 litres capacity with couplings - Plug-in ALU side and rear boards on gooseneck, approx. 400 mm high, anodised - Control lever on gooseneck protected by foldable cover - Separate air connection with air gun on gooseneck - BEKAMAX central lubrication system: 1x on gooseneck, 1x on 2-axle and 1x on 4-axle bogie - Variomax tool kit - Multi-coupling hydraulic connectors on gooseneck and at lowbed hook interface - 2 spare wheels - One 7-pin socket left and right, at front and rear of rear bogie for warning boards - Front bogie with separate air connection for impact wrench Gkodpfewcmhaox Af Rjb - Foldable steel bed extensions, adjustable in width from approx. 2,850 mm to 3,250 mm - Steel bed inserts can be placed in 2 positions for sunken load area - Steel mats with rubber flooring, approx. 12 mm thick - Thread-in options (⌀ 40 mm) every approx. 500 mm on the upper flange of the excavator deck outer tube for eye bolts - One locking point at every approx. 500 mm on extension with mechanical lock - Socket on rear bogie for remote steering cable control - 2 reversing lights on rear panel - Four extendable warning boards (by approx. 2,000 mm), each approx. 423 x 423 mm with position lights - 1 work light left + right on rear panel of gooseneck with separate on/off switches - Two INOX toolboxes, approx. 855 x 340 x 390 mm - 1-cylinder Hatz diesel engine (Silent Pack) - Radio remote control for after-steering

Stanje: novo, lastna masa: 14.800 kg, največja dovoljena obremenitev: 61.700 kg, skupna masa: 76.500 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck with rear chamfer of approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Loading Platform: • Extendable loading platform with rear chamfer of approx. 500 mm x 8° • 9 pairs of folding external lashing rings • 1 pair of recessed lashing rings at the front of the loading platform • Cutouts in the outer frame of the loading platform for attaching tension belts • Approx. 48 mm thick hardwood flooring, checker plate above the axles Landing Legs: • JOST mechanically operated landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: • BPW axles and suspension, 1st axle steering, 2nd and 3rd axle fixed, 4th and 5th axle follow-steering • Technical axle load: 12,000 kg • 1st, 4th, and 5th axles with electromagnetic reverse lock, activated via reverse gear or manually • Tyres: 235/75 R 17.5 3PMSF Brake System: • WABCO brake system in accordance with EU regulations including EBS-E (4S3M) Paintwork: • Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer • High-quality single-color two-component (2K) topcoat in MB 7350 Novagrau • Rear section metallized and painted in RAL 9010 (Pure White) Steel Construction: • Steel structure made from high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC (yield strength 355MPa) • S690QL/S700MC (yield strength 690MPa) Accessories: • One spare wheel with holder in front of the front wall • 2" king pin • Galvanized steel front wall, approx. 400 mm high • Front galvanized connection strip with yellow-red air couplings • 2 wheel chocks with holders mounted on the front wall • Rear mount on gooseneck for ALU drive-on ramps • Galvanized extendable wideners appx. 230 mm per side • Bracket for a beacon at the rear of the trailer • Galvanized supports under the chamfer of the loading platform • White reflector tape on the sides as per EU regulations, red at the extension and rear • Mounts for warning panels including socket left and right at the gooseneck and rear panel • Detachable ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • Rear galvanized plug-in stanchions removable (body length approx. 2,560 mm) • 3 pairs of WADER container pockets in the loading platform for a 20ft (30ft) or a 40ft container • 7 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform Godpfx Asma Hf Rof Rekb • Lifting axle on the front axle with TEBS E control according to the current axle load and loading condition • Movable mounting rails for ALU drive-on ramps at the rear of the vehicle • 20 x 20 mm square climbing strips at 200 mm intervals on the outer frame chamfer of the loading platform • BEKAMAX (Pico) centralized lubrication system with NLGI-2 standard grease and removable pump cover • Four extendable warning panels approx. 423 x 423 mm with a position light, extendable by approx. 400 mm • Holder for beacon mounted on the warning panels • European reflector plates (red-yellow) on the rear of the trailer • 80 km/h speed limit stickers at rear and both sides • Axle load gauge with load diagram included • HRM Metallisation (High Resistance Metallisation) of the outer frame • Complete steel structure is shot-blasted, then defined visible surfaces are metallized with ZINACOR 850 (zinc 85% - aluminum 15%) using hot finishing

Stanje: novo, lastna masa: 10.600 kg, največja dovoljena obremenitev: 39.400 kg, skupna masa: 50.960 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5, barva: siv, obratovalna teža: 10.600 kg, Oprema: ABS, Gooseneck: - Gooseneck with 30 mm hardwood flooring - Gooseneck at rear in straight version - 3 pairs of lashing rings (LC 5,000 daN) Extendable load floor: - Load floor in extendable configuration - 5 pairs of lashing rings foldable outward - 3 pairs of lashing rings foldable outward - 1 pair of lashing rings laying at the front end of the load floor Gkedpfx Afot Ag Uws Rsb - Cut-outs in the outer frame of the load floor for attaching tension straps - Approx. 48 mm hardwood flooring, checker plate covering above the axles Landing legs: - JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tyres: - BPW axles, two rigid axles, two self-steering axles - Air suspension with drum brakes, with lift/lower function - The self-steering axles are equipped with an electromagnetically operated reverse lock, which can be activated via reverse gear or manually - Axle tools - Tyres 205/65 R17.5 Brake system: - Brake system compliant with EU regulations with EBS-E (4S3M) Steel structure: - Steel construction made from high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system in accordance with EU regulations, lighting 24 Volt, ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets - Connections according to ISO: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Paintwork: - High-quality and durable corrosion protection on the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer - High-quality single-colour 2-component (2K) top coat in Novagrau - Rear section metallised and painted in RAL 9010 (Pure White) Included accessories: - One spare wheel with holder in front of the bulkhead - 2" king pin - Galvanised steel front wall approx. 400 mm high - Yellow-red air couplings on the galvanised connection bar at the front - 4 wheel chocks with holder at the front wall - Galvanised folding supports under the load floor slope - Holder for a warning beacon at the rear of the trailer - Galvanised extensions, extendable by approx. 230 mm per side - White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear - On the gooseneck and rear panel, left and right, one bracket each for warning panels including socket - European reflective markings (red-yellow) at the rear of the trailer - TPMS tyre pressure monitoring system according to ECE R 141 - On the gooseneck, plug-in ALU side walls and rear wall, approx. 2,440 x 400 mm - The rear, galvanised plug-in side stanchions are removable, length of the body approx. 2,560 mm - 7 pairs of WADER container pockets - 1x 20ft container on the load floor; 1x 40ft container on the load floor; 1x 40ft container above the gooseneck; 2x 20ft container - 7 pairs of stanchion sockets for plug-in stanchions 100 x 50 mm in the outer frame of the load floor - Lift axle on the front axle with control via TEBS E, depending on the current axle load and load condition - Sliding plug-in rail for ALU loading ramps at the rear of the vehicle - Anti-slip sand finish painted on the checker plates on the gooseneck and load floor - Four warning boards extendable by approx. 400 mm, approx. 423 x 423 mm, each with a position lamp - Holder for warning beacon on the warning boards - 80 km/h speed stickers at the rear and on both sides - Axle load gauge for determination of axle loads inclu

Stanje: novo, lastna masa: 15.450 kg, največja dovoljena obremenitev: 65.550 kg, skupna masa: 80.000 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 21.900 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 925 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimized platform length, approx. 3,700 mm long, with rear tapering of approx. 1,000 mm x 10° Technical fifth wheel load: 30,000 kg. For tractors: 4x2, 6x2, and 6x4 Loading Platform: Double-extendable loading platform, approx. 8,800 mm long with rear taper of approx. 500 mm x 10°. A support table approx. 300 mm wide is welded to the central beam, featuring elongated slots at the front and rear for optional bridge elements that can be hooked in and repositioned Pneumatic locking with conical locking pin and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles and Tyres: BPW axles and suspension, first axle self-steering, all other axles hydraulically and mechanically forced-steered First axle equipped with an electro-magnetic reverse lockout, activated via reverse gear and manually. Technical axle load: 12,000 kg. Air suspension with lift and lower valve Manufacturer by our choice Sockets and Lighting: 24-volt lighting system in accordance with EU regulations ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Complete HRM metallizing Full steel construction, shot-blasted, then hot-finished with ZINACOR 850 Paintwork: 6-stage finishing process: Complete steel construction shot-blasted after welding 1 coat of zinc-based primer, 1 coat of adhesion primer. Final paintwork in 2 coats of 2K paint in single-tone DB 7350 Novagrau, followed by cavity sealing with special wax Accessories: Detachable front wall made of steel, approx. 400 mm high Connection strip for supply lines to the tractor unit, fitted at the height of the outer frame profile ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets. If your pin configuration deviates from the ISO connector standard, please inform us 3 kW electro-hydraulic power unit for hydraulic functions (excluding hydraulic winches) 1 pair of plug-in ALU sidewalls on the gooseneck, approx. 400 mm high, anodized finish 3.5'' king pin. Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide 2 wheel chocks with holder in front of the front wall Mechanical landing legs with 2-speed gearbox and crank Gedjrigw Rspfx Af Rjkb Control valves for hydraulic ramps located on the right side of the vehicle 1 pair of mechanical rear supports Central lubrication system with 1 pump, BEKAMAX brand, using standard grease according to NLGI-2 Removable guard covering the pump(s) of the central lubrication system Remote steering from front and rear, controlled by cable remote with push buttons, with axle tracking control, no installation required on tractor unit Under the gooseneck and on the rear crossmember, one 7-pin socket with holder for warning signs each on left and right. One 7-pin socket on the rear crossmember Manual and documentation One-piece INOX stowage box, approx. 2,480 x 340 x 390 mm, straight design Please note that any special equipment and accessories will increase the unladen weight and correspondingly reduce the payload Warning package: 4 warning boards, approx. 423 x 423 mm, extendable by approx. 1,000 mm, incl. 2 LED position lights and brackets for beacon.

Stanje: novo, lastna masa: 15.420 kg, največja dovoljena obremenitev: 61.080 kg, skupna masa: 76.500 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading Platform: Extendable loading platform with rear chamfer approx. 500 mm x 8° 8 pairs of flip-out lashing rings 1 pair of recessed lashing rings at the front of the loading area Cutouts in the outer frame for securing straps Approx. 48 mm thick hardwood flooring; checker plate above the axles Two-Part Steel Ramps: One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering. Ramps with hydraulically folding ramp sections, hydraulic lifting and hydraulic lateral movement. Max load per pair: 50,000kg. Landing Legs: • JOST landing legs (mechanical) with two-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: BPW axles and suspension, 4th and 5th axle self-steering Technical axle load: 12,000 kg 4th and 5th axle with electromagnetically operated reverse lock, activated by reverse gear and manually Tyres: 235/75 R 17.5 3PMSF Brake System: Brake system according to EU regulations with EBS-E (4S3M) Godsl Sl Izspfx Af Rskb Sockets and Lighting: Electrical system according to EU standards, 24 Volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets Connections per ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component (2K) zinc-rich primer High-quality single-colour 2K topcoat in MB 7350 Novagrau Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Steel Structure: High-strength fine-grained steel construction Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Accessories: One spare wheel with holder in front of the front wall 2" king pin Galvanized steel front wall approx. 400 mm high Yellow-red air couplings on the galvanized front connection panel 2 wheel chocks with holder on the front wall Mounting at the rear of the gooseneck for ALU approach ramps Bracket for beacon at trailer rear Galvanized supports under sloped area of load floor White reflective tape per EU regulations on sides, extension, and red at the rear Electro-hydraulic unit under the rear of loading platform Warning sign brackets including sockets left/right on gooseneck and rear plate Control valves for ramps mounted right side of trailer Mudflap at rear of trailer Manual and documentation on USB stick 3.5" loose king pin supplied On gooseneck: ALU side boards and rear wall, plug-in approx. 2,440 x 400 mm (LxH) Removable rear galvanized stakes (Body length approx. 2,560 mm) 3 pairs WADER container pockets for 1x 20'/30' or 1x 40' container 6 pairs stake pockets for 100 x 50 mm plug-in stakes in outer frame Galvanized extensions, extendable by approx. 230 mm per side Lift axle on front axle, controlled via TEBS E according to actual axle load and current payload Square climbing strips 20 x 20 mm every 200 mm on outer frame chamfer of load floor Checker plate coverings above the king pin and loading area...

Stanje: rabljeno, barva: rdeča, Leto izdelave: 2016, Faymonville F-S43-1BGS. Letnik: 2016. 9-tonske osi SAF. Teža: 9030 kg. Maksimalna teža: 45.000 kg. Nosilnost pripetka: 18.000 kg. 7,5 metra, raztegljivo. Hidravlični sistem, upravljanje iz kabine tovornjaka (NATO). EBS ABS ALB. Daljinski upravljalnik. Servo volan na 3 krmilnih osi. Zračna vzmetitev. Priprava za pritrdilne elemente (twistlocks). Dimenzije ploščadi: D: 13.600 mm. Š: 2550 mm. V: 1480 mm. Pnevmatike: 385/65R22,5, 50% ostale življenjske dobe. ID št.: 561. Splošni pogoji poslovanja podjetja Heinhuis veljajo za vse oglase, ponudbe in kalkulacije podjetja Heinhuis, vse pogodbe, sklenjene s podjetjem Heinhuis, in pogajanja, ki jim predhodijo. S kakršnim koli odgovorom potrdite veljavnost splošnih pogojev poslovanja podjetja Heinhuis in izjavljate, da ste se seznanili s temi splošnimi pogoji poslovanja. Naše cene so izvozne neto cene. = Dodatne informacije = Letnik: 2016 Lastna teža: 9.030 kg Nosilnost: 35.970 kg Dovoljena skupna masa: 45.000 kg Raztegljiva nadgradnja: Da Gksdpfx Afozybx Es Reb = Podatki o podjetju = Za več informacij:

Stanje: rabljeno, največja dovoljena obremenitev: 36.515 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2023, naslednji pregled (TÜV): 05/2027, Oprema: ABS, Izvod opreme: Gjdpfozqiiasx Af Rokb V-priklop: V-priklop s poševnimi robovi, spredaj pribl. 45° in zadaj pribl. 750 mm x 10°. 3 pari pritrdilnih obročev (LC 5.000 daN). Tla iz trdega lesa, debeline pribl. 30 mm. Platforma z raztegljivo izvedbo: Platforma z raztegljivo izvedbo in zadaj poševnimi robovi pribl. 1.000 mm x 8°. 5 parov pritrdilnih obročev, zunanji, z možnostjo zlaganja (LC 5.000 daN). 3 pari pritrdilnih obročev, zunanji, z možnostjo zlaganja (LC 10.000 daN). 1 par pritrdilnih obročev, nameščen vodoravno na sprednjem delu platforme (LC 10.000 daN). Tla iz trdega lesa, debeline pribl. 48 mm, nad osmi rebrasto jeklo. Osi: Osi BPW in vzmetenje, vse osi so hidravlično-mehansko prisilno usmerjene. Tehnična obremenitev osi: 12.000 kg na os. Zračno vzmetenje z ventilom za dvig in spuščanje. Orodje za osi. Pnevmatike: Pnevmatike 245/70 R 17.5 3PMSF, indeks obremenitve (146/146 F) – znamka po naši izbiri. Podporne noge: JOST podporne noge (mehanske) z 2-stopenjskim menjalnikom za pribl. 24 t nosilnosti (pribl. 50 t testna obremenitev). Zavorna sistema: Zavorna sistema v skladu z direktivami EU s sistemom EBS-E (2S2M) brez povezovalnih vodov do vlečne enote. Lakiranje: Odlična in dolgotrajna protikorozijska zaščita standardno peskanega jeklenega okvirja, zagotovljena s 2-komponentno (2K) osnovo z večjo vsebino cinka. Kakovostno 2-komponentno (2K) končno lakiranje v eni barvi, RAL 3002, karminska rdeča. Zadnji del je metaliziran in lakiran v RAL 9010 (čista bela). Metalizirano lakiranje ni mogoče. Jeklena konstrukcija: Jeklena konstrukcija iz visoko trdnih finozrnatih jekel. Vrste jekla: S355J2+N/S355MC (meja tečenja 355 MPa), S690QL/S700MC (meja tečenja 690 MPa). Električna napeljava: Električna napeljava v skladu z direktivami EU, razsvetljava 24 voltov ASPÖCK-NORDIK (ASS3), ASPÖCK-UNIBOX na sprednji priključni plošči z vtičnicami 24N, 24S in 15-polna. Priključek v skladu s standardom ISO. 24N ISO-1185, 24S ISO-3731, 15-polni ISO-12098. Vključeno naslednje dodatne opreme: - 2-palčni kraljevi zatič - pocinkana jeklena sprednja plošča, pribl. 400 mm visoka - rumeno-rdeče zračne spojke na pocinkani sprednji priključni plošči - 4 klini z nosilci na sprednji plošči (± 5 kg) - nosilec za rezervno kolo pred sprednjo ploščo - elektro-hidravlična agregat (± 45 kg) - dodatno krmiljenje od spredaj in zadaj s kabelskega daljinskega upravljalnika preko gumbov, z nadzorom enoslednosti osi (brez vgradnje v vlečno enoto) - nosilec na zadnjem delu V-priklopa za aluminijaste rampe - evropske odsevne table (rdeče-rumene) na zadnjem delu prikolice - rumen odsevni trak v skladu z direktivami EU na straneh, na raztegljivi platformi in na zadnji strani prikolice - na V-priklopu in zadnji plošči, na levi in desni strani, po en nosilec za opozorilne table, vključno z vtičnico - nosilec za okroglo luč na zadnji strani prikolice - pocinkani zložljivi nosilci pod poševnino platforme - odbijač blata na zadnji strani prikolice - priročnik in opis na USB-pomnilniku - nalepka za omejitev hitrosti 80 km/h na zadnji strani in na obeh straneh - manometer za obremenitev osi, za ugotavljanje obremenitve osi, vključno z diagramom obremenitve.

Stanje: dober (rabljeno), konfiguracija osi: 2 osi, dovoljena osna obremenitev (os 1): 12.000 kg, dovoljena osna obremenitev (os 2): 12.000 kg, vzmetenje: hidravlika, velikost pnevmatike: 245/70R17,5, barva: siv, Leto izdelave: 2016, Faymonville F-S42-2ACB. Letnik: 2016. 12 ton osi SAF Pendel-X. Teža: 12.700 kg. Nosilnost: 36.300 kg. Maksimalna teža: 49.000 kg. Nosilnost pete: 25.000 kg. Raztegljivost: 4,2 metra. Razširitev: 3 metre. 2 x 25 cm razširitev, vključno z možnostjo razširitve. Hidravlično vzmetenje. Hidravlično odstranljiva vlečna prikolica (gooseneck). Hidravlični sistem, združljiv z NATO. Radijski daljinski upravljalnik. EBS ABS ALB. Aluminijaste plošče na prikolici. 3 odstranljivi deli tal. Prevleka iz cinka. Dimenzije: Prikolica (gooseneck): D: 3700 mm. Š: 2480 mm. V: 1600 mm. Višina pete: 1200 mm. Platforma: D: 6350 mm. Š: 2550 mm. V: 350 mm. Debelina tal: 220 mm. Zadnji del prikolice: D: 2600 mm. Gkjdpfx Afozp Nrro Rsb Š: 2550 mm. V: 1000 mm. Pnevmatike: 245/70R17,5, 70 %. Nemška prikolica! ID št.: 565. Splošni pogoji Heinhuis veljajo za vse oglase, ponudbe in cenitve družbe Heinhuis, vse pogodbe, sklenjene s strani družbe Heinhuis, in pogajanja, ki jim sledijo. S kakršnim koli odzivom potrdite veljavnost splošnih pogojev družbe Heinhuis in izjavljate, da ste se seznanili s temi splošnimi pogoji. Naše cene so izvozne neto cene. = Dodatne informacije = Splošne informacije Letnik: 2016 Konfiguracija osi Velikost pnevmatik: 245/70R17,5 Znamka osi: SAF Pendel-X Vzmetenje: hidravlično vzmetenje Zadnja os 1: dvojne pnevmatike; maks. obremenitev osi: 12.000 kg; krmiljena; profil pnevmatik levo znotraj: 70 %; profil pnevmatik levo zunaj: 70 %; profil pnevmatik desno znotraj: 70 %; profil pnevmatik desno zunaj: 70 % Zadnja os 2: dvojne pnevmatike; maks. obremenitev osi: 12.000 kg; krmiljena; profil pnevmatik levo znotraj: 70 %; profil pnevmatik levo zunaj: 70 %; profil pnevmatik desno znotraj: 70 %; profil pnevmatik desno zunaj: 70 % Teže Lastna teža: 12.700 kg Nosilnost: 36.300 kg Maksimalna dovoljena masa: 49.000 kg Stanje Tehnično stanje: dobro Vizualno stanje: dobro = Informacije o podjetju = Za več informacij:

Stanje: rabljeno, barva: rumena, Leto izdelave: 2013, Faymonville STZ-3UB. Letnik: 2013. 10-tonske osi SAF. Teža: 12.300 kg. Nosilnost: 29.700 kg. Maksimalna teža: 42.000 kg. Obremenitev kraljice: 18.000 kg. Servo volan, 3 krmiljene osi. Režana plošča. Vinska. Aluminijaste plošče na sprednjem delu. Hidravlični sistem prikolice, združljiv z NATO. Radijski daljinski upravljalnik. Zračna vzmetitev. Hidravlični most, ki se dviga od tal do sprednjega dela. Dolžina: 3000 mm. 2 dvižna oporna točka na zadnji strani, hidravlična. 2-delna hidravlična rampa: Dolžina: 2800 + 1700 mm. Dimenzije: Sprednji del: D: 3750 mm. Š: 2500 mm. Gsdpezybhyjfx Af Rjkb V: 1380 mm. Višina kraljice: 1150 mm. Plošča: D: 9600 mm. Š: 2550 mm. V: 900 mm. Pnevmatike: 245/70R17,5, 80 %. ID št.: 436. Splošni pogoji poslovanja družbe Heinhuis veljajo za vsa oglaševanja, ponudbe in ponudbe družbe Heinhuis, za vsa sklenjena sporazuma s podjetjem Heinhuis in za pogajanja, ki jim sledijo. S kakršnim koli odgovorom potrjujete veljavnost splošnih pogojev poslovanja družbe Heinhuis in izjavljate, da ste se seznanili s temi splošnimi pogoji poslovanja. Naše cene so izvozne neto cene. = Dodatne informacije = Letnik: 2013 Lastna teža: 12.300 kg Nosilnost: 29.700 kg Dovoljena skupna masa: 42.000 kg = Podatki o podjetju = Za več informacij:

Stanje: novo, lastna masa: 10.000 kg, največja dovoljena obremenitev: 41.600 kg, skupna masa: 51.600 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Loading Platform: - Gooseneck, length approx. 4,100 mm with central beam - Extendable loading platform, length approx. 9,500 mm with rear taper approx. 350 mm x 10° and integrated hook-on bar for attaching loose ALU approach ramps - Pneumatic locking system with conical locking bolts and reinforced locking positions - Supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles, Suspension, and Tyres: - BPW axles and suspension, all axles hydro-mechanically forced steered - Mounted on turntable - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - Tyres 235/75 R17.5, twin-mounted Paintwork: - 6-coat surface treatment - Complete steel structure shot-blasted after welding - One coat of zinc-based primer, one coat of adhesion primer - Final paintwork with 2 layers of 2-component (acrylic) paint, single colour in MB 7350 Novagrau, followed by cavity sealing with special wax Steel Structure: - Steel structure made from high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355MPa) - S690QL/S700MC (yield strength 690MPa) - Welders certified according to DIN-EN 287-1 - Welding process MAG according to EN ISO 4063, shielding gas M21 according to EN ISO 14175 Accessories: - Steel front wall, approx. 1,600 mm high - Round NATO socket at the front connection strip - 3 kW electro-hydraulic unit for controlling hydraulic functions - 4 pairs of recessed lashing rings in the outer frame of the gooseneck - 4 pairs of stake pockets integrated into the outer frame of the gooseneck for stakes approx. 100x50 mm - 1 transverse stake pocket strip mounted in the floor of the gooseneck for stakes approx. 100x50 mm (1x rear on gooseneck) - 2'' kingpin - Mechanical landing legs with 2-speed gearbox and hand crank - JOST Module B – static test load = 50,000 kg - On the gooseneck and loading area, approx. 32 mm wooden flooring in ALU-omega profiles - One locking position on the extension, approx. every 500 mm - 10 pairs of recessed folding lashing rings in the outer frame of the loading area, folding outwards - 6 pairs of stake pockets integrated into the outer frame of the loading area for stakes approx. 100x50 mm Gedpfxeiuy Nlj Af Rekb - 2 transverse stake pocket strips mounted in the floor of the loading area for stakes approx. 100x50 mm - INOX toolbox approx. 1,250 x 500 x 550 mm - Tapered end crossmember of the vehicle, approx. 350 mm 10° - Integrated hook-on bar for loose ALU approach ramps at the rear crossmember of the vehicle - 1 pair of drop tube supports at the rear crossmember - Mudguards on all axles - Central lubrication system with 1 pump - Remote steering from front and rear operable via cable remote control with push button, including single-track monitoring of the axles - Under the gooseneck and at the rear crossmember, left and right, each with a 7-pin socket for warning panels - One 7-pin socket at the rear crossmember - Container locks "TWIST-LOCKS" in the loading area for transport of 2x 20ft and 1x 40ft containers - Radio remote control for rear steering in addition to cable remote control, with 2 indicator lights on the receiver for single-track monitoring - 2 axle load gauges + axle load diagram - 4 warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Standard HRM Metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible areas hot-coated in metallic finish using ZIN

Stanje: rabljeno, barva: rdeča, Leto izdelave: 2020, Faymonville F-S43-1AAF. Leto: 2020. 12 ton SAF osi. Največja dovoljena masa: 61.000 kg. Nosilnost kraljevega bolta: 25.000 kg. Servo volan, 3 volanske osi. Hidravlični sistem, združljiv z NATO. EBS ABS ALB. 2 x raztegljiva: 1: 8,15 metra. 2: 8,45 metra. Skupna dolžina: 16,5 metra! Orodjarna + aluminijaste plošče na prikolici. 2 x 25 cm razširjeno. Radijski daljinski upravljalnik. Rezervna pnevmatika. Hidravlično vzmetenje (levi in desni del ločeno). Centralni sistem za mazanje. Prevlečeno s cinkom. Dodatna vmesna platforma: 50 cm. 2-smerne hidravlične rampe: - Dolžina: 2800 mm + 1400 mm. - Hidravlična premikanje od leve proti desni. Dimenzije: Priključek: D: 3650 mm. Š: 2550 mm. V: 1550 mm. Višina kraljevega bolta: 1300 mm. Platforma: D: 12.000 mm. Š: 2550 mm. V: 950 mm. Pnevmatike: 245/70R17,5, 80 %. Odlično stanje! Gedpfx Afjzya R He Rekb ID št.: 601. Splošni pogoji poslovanja podjetja Heinhuis veljajo za vse oglase, ponudbe in cenitve podjetja Heinhuis, vse pogodbe, sklenjene s podjetjem Heinhuis, in za pogajanja, ki jim sledijo. S kakršnimkoli odgovorom sprejemate veljavnost splošnih pogojev poslovanja podjetja Heinhuis in izjavljate, da ste se seznanili s temi splošnimi pogoji poslovanja. Naše cene so izvozne neto cene. = Dodatne informacije = Leto izdelave: 2020. Največja dovoljena masa: 61.000 kg. Raztegljiva nadgradnja: Da. = Podatki o podjetju = Za več informacij:

Stanje: novo, lastna masa: 11.000 kg, največja dovoljena obremenitev: 38.500 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm hardwood flooring Load Area: - Extendable loading area with rear taper approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses fitted with square climbing strips 15 x 15 mm, including lower extensions - Between the 1st and 2nd axle, a pair of fixed wheel recesses with cover, approx. 1,610 x 970 x 400 mm - Recess in the bevel as well as protruding into the loading area for parking excavator dipper stick approx. 2,900 x 750 x 210/290 mm - 1 pair of lashing rings, installed flat at the front of the load area (LC 10,000 daN) - 5 pairs of folding lashing rings on the outside (LC 5,000 daN) - 2 pairs of folding lashing rings on the outside (LC 10,000 daN) - 2 pairs of lashing rings in the dipper stick recess (LC 5,000 daN) - Cut-outs in the outer frame of the load area for securing straps (LC 2,000 daN) - Incl. three-part removable galvanized covers over the wheel recesses – max. point load 3.5 t / pc. Two-piece Steel Ramps: - One pair of galvanized, two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood surfacing - Ramp with hydraulically folding ramp sections, hydraulic lifting gear, and hydraulically adjustable Axles and Tyres: - BPW axles and suspension, 2 rigid axles, 1 steering trailing axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lifting and lowering valve - Axle tool kit - Tyres 235/75 R 17.5 - TPMS tyre pressure monitoring system in accordance with ECE R 141 Accessories Included: - Mounts for warning signs left and right at the gooseneck and at the rear, each with socket - One spare wheel - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings at the galvanized front connector strip - 4 wheel chocks - Galvanized, extendable outriggers approx. 230 mm per side - Galvanized folding supports beneath the loading area bevel - Rear trailer bracket for rotating beacon - Cover plates for bridging the gap between ramps and load area - White reflective tape to EU regulations, sides and on extensions; rear in red - Electro-hydraulic unit installed at the rear beneath the loading area Gksdpfx Afoup U Hzo Rjb - Ramp control valves mounted on right trailer side - European reflective panels (red-yellow) on rear of trailer - Four extendable warning boards, approx. 423 x 423 mm, with position light - Bracket for rotating beacon on warning boards - Removable ALU side boards and rear board on gooseneck approx. 2,440 x 400 mm - Rear galvanized removable stakes (structure length approx. 2,560 mm) - 2 pairs of WADER container pockets in loading area for 20ft or 30ft container - 3 pairs of socket pockets for stakes 100 x 50 mm in outer frame of loading area - Removable, galvanized intermediate table with 1 pair of WADER container pockets - Square climbing strips 20 x 20 mm spaced every 200 mm on outer frame at loading bevelling - Painted sand layer on chequer plates of the gooseneck and loading area for anti-slip protection - 80 km/h speed stickers rear and both sides - Load manometer for axle load measurement, including load chart.

Stanje: rabljeno, barva: rdeča, Leto izdelave: 2016, Faymonville F-S43-1EJB. Leto: 2016. 9-tonske osi BPW. Maksimalna teža: 45.000 kg. Nosilnost čepa: 18.000 kg. EBS ABS ALB. Hidravlični sistem, primeren za standard NATO. Hidravlično vzmetenje. 9500 mm. Pnevmatike: 385/65R22,5, 80-odstotna obraba. Številka ID: 521. Splošni pogoji poslovanja družbe Heinhuis veljajo za vse oglase, ponudbe in cenitve družbe Heinhuis, za vse pogodbe, ki jih sklene družba Heinhuis, ter za pogovore, ki jim predhodijo. S kakršnim koli odgovorom se strinjate z veljavnostjo splošnih pogojev poslovanja družbe Heinhuis in potrđujete, da ste se seznanili s temi splošnimi pogoji poslovanja. Naše cene so izvozne neto cene. = Dodatne informacije = Leto izdelave: 2016 GVW: 45.000 kg Gjdpfxezyp T Do Af Rekb = Informacije o podjetju = Za več informacij:

Stanje: novo, lastna masa: 22.700 kg, največja dovoljena obremenitev: 79.300 kg, skupna masa: 102.000 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 11.000 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 920 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 22.700 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize load platform length, approx. 3,750 mm long, rear with chamfer approx. 850 mm x 10° - Hydraulically liftable and lowerable, stroke ± 250 mm including hydraulic connection linked to the hydraulic axle compensation of the first two axles - Open in the rear third - For tractor units: 6 x 4 and 8 x 4 Load platform: - Extendable load platform, approx. 11,000 mm long with rear chamfer approx. 500 mm x 10° - Recess in the platform and into the chamfer for receiving the excavator dipper stick, approx. 4,240 x 900 x 440 mm - Pneumatic locking with conical locking pin and reinforced locking positions, supply lines protected within the extendable beams, automatically adapting to the actual platform length Ramps: - One pair of two-piece steel ramps approx. 4,650 mm long and 900 mm wide - Hydraulically foldable ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 215 mm inward - 25 mm "Super Grip" rubber flooring and approx. 5 mm checker plate as additional reinforcement on the chamfered section of the platform - Square climbing strips 20x30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, Suspension, and Tires: - PA-X axle system, all axles hydro-mechanically forced steered - Steering performance of the first two axles can be optimally adjusted to the platform length, both mechanically and hydraulically - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-fitted locking pins for securing in raised position - 245/70 R 17.5 3PMSF Accessories included: - Plug-in steel front wall, approx. 400 mm high - Supply line connection strip for tractor unit, mounted at the height of the outer frame profile - 1 spare wheel - Outer beams of gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from front, then every approx. 400 mm - 2 pairs of screw-in lashing rings included - Chequer plate covering over the gooseneck - On gooseneck: 1 pair of removable anodized ALU side walls, approx. 400 mm high - On gooseneck: 1 removable anodized ALU rear wall, approx. 400 mm high - 3.5" king pin / 2" king pin mounted - Guide plate of the gooseneck for fifth wheel plate, approx. 500 mm wide - 4 chocks - 4 axle load gauges - Mechanical drop tube supports at the front - 1 one-piece INOX toolbox, approx. 2,480 x 340 x 390 mm - Mechanical drop tube supports at the front - Continuous steel deck with baked-in sand layer as anti-slip protection on the platform - 1 intermediate table, approx. 500 mm wide, for the extension, with slotted holes for insertable and relocatable bridging elements - Sand coating on support surfaces of the intermediate table Godpfxok Af Svs Af Rskb - Mechanical locking for securing the intermediate table on the extension - 8 pairs of stake pockets in the outer frame - Extendable (galvanized) widenings, approx. 230 mm per side - 1 pair of hydraulic rear supports - Central lubrication system - 1 reversing spotlight each on left and right rear of the vehicle - 3 kW electro-hydraulic power unit - Loose widening planks in reinforced steel U-frame - Radio and cable remote control - 4 warning signs, approx. 423 x 423 mm

Stanje: rabljeno, barva: modra, Leto izdelave: 2017, Faymonville F-S42-1ACA. Letnik: 2017. 11,2-tonske osi SAF. Teža: 12.110 kg. Nosilnost: 25.890 kg. Gkodpjzya Rgofx Af Rjb Maksimalna teža: 38.000 kg. Nosilnost priklopa: 18.000 kg. Sistem EBS ABS ALB. Hidravlični sistem priklopnega vozila, združljiv s standardom NATO. Hidravlično snemljiv priklop. Zračna vzmetitev. Rezervno kolo. Servo volan. Daljinski upravljalnik. 5-metrska raztegljiva platforma. Dimenzije: Osnava: D: 4000 mm. Š: 2550 mm. V: 1550 mm. Višina priklopa: 1200 mm. Platforma: D: 6300 mm. Š: 1000 - 2540 - 3000 mm. V: 450 mm. Debelina platforme: 300 mm. Zadnja stran priklopnika: D: 2800 mm. Š: 2550 mm. V: 950 mm. Pnevmatike: 235/75R17,5, 80 %. Na voljo 2 kosa! Priklopnik nemške izdelave! Številka ID: 596. Splošni pogoji Heinhuis veljajo za vse oglase, ponudbe in cenitve družbe Heinhuis, za vsa sklenjena sporazuma s strani Heinhuis in za pogajanja, ki predhodijo tem sporazumom. S kakršnim koli odzivom potrjujete veljavnost splošnih pogojev družbe Heinhuis in izjavljate, da ste se seznanili s temi splošnimi pogoji. Naše cene so izvozne neto cene. = Dodatne informacije = Letnik: 2017 Lastna teža: 12.110 kg Nosilnost: 25.890 kg Dovoljena skupna masa: 38.000 kg Raztegljiv nadgradni del: Da = Informacije o podjetju = Za več informacij:

Stanje: novo, konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 10.000 kg, dovoljena osna obremenitev (os 2): 10.000 kg, dovoljena osna obremenitev (os 3): 10.000 kg, dolžina tovornega prostora: 29.000 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 2.850 mm, skupna dolžina: 29.000 mm, skupna širina: 2.540 mm, skupna višina: 2.850 mm, vzmetenje: zrak, velikost pnevmatike: 385/65-R22.5, Leto izdelave: 2026, Oprema: ABS, - BPW-osovine - EBS - Zračno vzmetenje - Kolutne zavore - Centralno mazanje Gsdpfezhxgiox Af Rekb NOVO MAX210-Z-3AA-13.60-22.5-2.54, neposredno na zalogi Tehnični podatki MAX210-Z-3AA-13.60-22.5-2.54 Skupna masa: 48.000 kg / Pritisk na sklopki: 18.000 kg / Osna obremenitev: 30.000 kg / Lastna teža: 11.456 kg / Nosilnost cca.: 36.544 kg / Višina sklopke (naloženo): 1.150–1.250 mm / Polmer obračanja: 2.300 mm Dolžina nakladalne površine: 13.600 mm / 2-krat izvlečna (2 x 770 mm) do 2.900 mm / Medosna razdalja: 1.810 mm Tehnični opis: Izvlečna nakladalna površina s pnevmatsko zaporo / V osrednjem škatlastem okvirju je fiksna vmesna miza ± 250 mm / 8 parov navzven preklopnih pritrdilnih ušes (LC 5.000 daN) / 3 pari navzven preklopnih pritrdilnih ušes (LC 10.000 daN) / Izrezi v zunanjem okviru za obešanje trakov (LC 2.000 daN) Pnevmatike: Pnevmatike 385/65 R22.5 (znamka: Goodyear) Sistem za nadzor tlaka v pnevmatikah (TPMS): TPMS v skladu z ECE R 141 Osovine: BPW-osovine s kolutnimi zavorami, zračno vzmetene z dvižno/spustnim ventilom. Vse osi hidromehansko prisilno krmiljene. Tehnična osna obremenitev: 10.000 kg (ET 0) Zavorni sistem: WABCO zavorni sistem v skladu z EU-predpisi z EBS-E sistemom (2S2M), brez priključnega kabla na traktor. Jeklena konstrukcija: Jeklena konstrukcija iz visokokakovostnega drobnozrnatega jekla. Kakovost jekla: S355J2+N/S355MC (meja elastičnosti 355 MPa) / S690QL/S700MC (meja elastičnosti 690 MPa) Električna napeljava: Električna napeljava v skladu z EU predpisi, osvetlitev 24 V ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX na pocinkani priključni letvi spredaj s 24N-, 24S- in 15-polnimi vtičnicami. Priključki po ISO / 24N ISO-1185 / 24S ISO-3731 / 15-polni ISO-12098 Opozorilne table: Pod gosjim vratom in zadaj, levo in desno, nosilec za opozorilne table z vtičnico. Opcije: • Manevriranje spredaj in zadaj prek kablovskega daljinca z nadzorom PDC osvetlitve za poravnavo osi (brez montaže na traktor) • Elektrohidravlična enota (cca. 45 kg) • 2 zagozdi za kolesa z nosilcem na pregradi • Kraljevski zatič 2" • Pocinkana jeklena pregrada, cca. 1.600 mm visoka, EN12642-XL • Bela odsevna letev v skladu z EU-predpisi po celotni dolžini in širini. Rdeča zadaj. • EU označevalne table (rdeče-rumene) zadaj. • Nosilec za rotacijsko luč zadaj. • Nakladalna tla iz 30 mm debelega trdega lesa, ojačana z omega profili (cca. 298 kg). • 10 parov držal za kole (cca. 100 x 50 mm), v zunanjem okviru nakladalnega poda. • 1 nosilec za rezervno kolo pod nakladalnim podom desno. • BEKAMAX (Pico) centralni sistem mazanja z 2 črpalkama. • 6 parov izrezov v nakladalnem podu za WADER kontejnerske ključavnice, za 1 x 20', 2 x 20', 1 x 40' ali 1 x 45' kontejner. • 5 parov profilov za kole, nameščenih prečno v nakladalno dno, za kole 100 x 50 mm • Pocinkan prostor za shranjevanje pod nakladalnim podom (2.390 x 720 x 400 mm) • Kljuke za vrvi (8 mm), na vsakih cca. 500 mm pod robnim profilom gosjega vratu in nakladalnega poda • Lestev za vzpenjanje, nameščena levo v smeri vožnje • Inox orodjarna • LED razsvetljava • 10 parov vtičnih kolov (100 x 50 mm, dolžina 1.000 mm) • 8 kontejnerskih ključavnic Splošne informacije Letnik izdelave: 2026...

Stanje: dober (rabljeno), konfiguracija osi: > 3 osi, dovoljena osna obremenitev (os 1): 7.600 kg, dovoljena osna obremenitev (os 2): 7.600 kg, dovoljena osna obremenitev (os 3): 7.600 kg, prva registracija: 03/2013, vzmetenje: zrak, velikost pnevmatike: 205/65R17,5, barva: rdeča, Leto izdelave: 2013, = Dodatne možnosti in dodatna oprema = - Zračna vzmet - Centralno mazanje = Opombe = Faymonville STN-4UBX. Letnik: 2013. 7,6-tonske osi SAF. Maks. dovoljena masa: 40.000 kg. Obremenitev kraljevega boljena: 18.000 kg. Hidravlični sistem po standardu NATO. EBS, ABS, ALB. Aluminijaste stranske stene na vratu prikolice. Vrvni vitel z daljinskim upravljalnikom. Hidravlična ploščad (povezava med tovorno površino in vratom prikolice): - Dolžina: 3000 mm. Tlak s vzdolžnimi rezi. Centralni sistem za mazanje. Prevožena razdalja osi: 329.395 km. Zračna vzmet. 3. in 4. os sta izvedeni kot sledilne osi. Hidravlične rampe (2-delne): - Dolžina: 3000 + 1750 mm. - Hidravlično nastavljive vstran. Dimenzije: Vrat prikolice: D: 3750 mm. Š: 2480 mm. V: 1400 mm. Višina kraljevega boljena: 1150 mm. Tovorna površina: D: 9630 mm. Š: 2550 mm. V: 800 mm. Pnevmatike: 205/65R17,5 (globina profila 80 %). Nemška prikolica! ID št.: 518. Za vse oglase, ponudbe in ponudbe podjetja Heinhuis ter za vse pogodbe, sklenjene s podjetjem Heinhuis, in za pogajanja, ki jim predhodijo, veljajo splošni pogoji podjetja Heinhuis. Z vsakim obliko stika potrjujete veljavnost splošnih pogojev podjetja Heinhuis in izjavljate, da ste se seznanili s temi splošnimi pogoji. Naše cene so neto izvozne cene. = Dodatne informacije = Konfiguracija osi Velikost pnevmatik: 205/65R17,5 Znamka osi: SAF Vzmetenje: Zračna vzmet Zadnja os 1: Dvojne pnevmatike; maks. obremenitev osi: 7600 kg; globina profila leve notranje pnevmatike: 80 %; globina profila leve zunanje pnevmatike: 80 %; globina profila desne notranje pnevmatike: 80 %; globina profila desne zunanje pnevmatike: 80 % Zadnja os 2: Dvojne pnevmatike; maks. obremenitev osi: 7600 kg; globina profila leve notranje pnevmatike: 80 %; globina profila leve zunanje pnevmatike: 80 %; globina profila desne notranje pnevmatike: 80 %; globina profila desne zunanje pnevmatike: 80 % Zadnja os 3: Dvojne pnevmatike; maks. obremenitev osi: 7600 kg; vodljiva; globina profila leve notranje pnevmatike: 80 %; globina profila leve zunanje pnevmatike: 80 %; globina profila desne notranje pnevmatike: 80 %; globina profila desne zunanje pnevmatike: 80 % Zadnja os 4: Dvojne pnevmatike; maks. obremenitev osi: 7600 kg; vodljiva; globina profila leve notranje pnevmatike: 80 %; globina profila leve zunanje pnevmatike: 80 %; globina profila desne notranje pnevmatike: 80 %; globina profila desne zunanje pnevmatike: 80 % Teže Dovoljena masa: 40.000 kg Gkodpezzxnasfx Af Rjb Funkcionalnost Višina tovorne površine: 80 cm Stanje Tehnično stanje: dobro Vizualno stanje: dobro Poškodbe: brez = Podatki o podjetju = Za več informacij: