Faymonville Max Trailer 2-Achs-Tiefbett Mit Pendelachsen nakup rabljenega (57.277)

Stanje: novo, lastna masa: 12.900 kg, največja dovoljena obremenitev: 34.100 kg, skupna masa: 47.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 350 mm, vzmetenje: drugo, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 12.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm in length - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2, and 6x4 Loading Platform: - Low-bed with external beams, extendable “SUPER LOW” design, approx. 6,850 mm in length - Low-bed with fixed hardwood flooring, approx. 40 mm thick, with mechanical locking device Rear Chassis: - Rear chassis with closed outer frame, chequer plate covering, and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings, foldable to the outside - 1 pair of lashing rings recessed in the trough - 2 pairs of stake pockets for insertable stakes 100 x 50 mm in the external frame Pendulum Axle and Tyres: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and safety locking pins for securing in raised position - Axles painted with two layers of single-colour 2K paint in “FAY-Grey-34-0260” - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 - TPMS tyre pressure monitoring system according to ECE R 141 Accessories: - Preparation for the installation of bolt-on container locators for 1 x 20ft or 1 x 40ft container on the outer girders - 2" king pin - One galvanized steel front wall, approx. 400 mm high - One spare wheel - Yellow-red air couplers on the galvanized front connection bar - 4 wheel chocks Nwjdpfx Ahohlz R So Roi - Remote steering from front and rear, operable via wired remote control with push buttons, with single-track alignment control - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of screw couplings - Electro-hydraulic power unit - White reflective tape in accordance with EU regulations on sides, extension, and rear - European reflective plates (red-yellow) on the rear of the trailer - One bracket on each side of gooseneck and rear plate for warning panels, including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on outer beam for mounting screw-on RUD Rings VLBG-4 - Detachable ALU side boards and rear board on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized insertable stakes are removable (body length approx. 2,560 mm) - Gooseneck rear upper area covered with removable cover - 5 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading area - Folding extensions, approx. 230 mm per side - 2 pairs of bolted RUD Rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the mounting hooks of the low-bed - Anti-skid sand layer painted on loading surface - 80 km/h speed stickers at rear and both sides - Spoon boom trough at rear chassis closed at rear with plug-in plate - Four extendable warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for rear axle steering in addition to cable remote, with indicator lights on receiver for alignment control - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard NLGI-2 grease - Load pressure gauge for determining axle loads - HRM Metallisation (High Resistance Metallisation) of outer frame - Complete steel structure shot blasted, then all defined visible areas metallized and finished with ZINACOR 850 (zinc 85% - aluminium 15%) hot galvanizing

Stanje: novo, lastna masa: 17.500 kg, največja dovoljena obremenitev: 43.500 kg, skupna masa: 61.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.750 mm, višina nakladalnega prostora: 400 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: Nwjdpoh Hm Thsfx Ah Rei - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - For tractor units: 6x4 or 8x4 Lowbed: - Lowbed with external beams, extendable version, "SUPER LOW" design, approx. 7,550 mm long - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking device - Service lines are protected within the extendable beams and automatically adjust to the lowbed length Rear Undercarriage: - Rear chassis with closed outer frame, checker plate cover, and continuous prism-shaped excavator trough approx. 1,450/900 x 505 mm, open at the rear - 2 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame Axles and Tires: - "PENDULUM AXLE", all axles hydro-mechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 / 3PMSF Included Accessories: - Prepared for bolt-on container positioning for 1x 20ft or 1x 40ft container on the outer beams - 2" kingpin - Galvanized steel front wall approx. 400 mm high - One spare wheel with holder - At the galvanized front adapter bar yellow-red air couplings - 4 wheel chocks - Remote rear steering from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Hydraulic line connections from gooseneck to lowbed with multi-coupling instead of screw coupling - Electro-hydraulic power pack - White reflective tape to EU specifications on sides, extension, and rear red - 2 wooden blocks 500x250x200 mm - European reflective plates (red-yellow) on the trailer rear - At the gooseneck and rear wall left and right each a bracket for warning boards including socket - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 - Load gauge for determination of axle loads including load diagram - On the gooseneck, plug-in ALU side and rear boards approx. 2,000 x 400 mm - The rear galvanized insert posts are removable (body length approx. 2,120 mm) - Separate air connection for air gun on the gooseneck - Duomatic air coupling from gooseneck to lowbed - Rear upper section of gooseneck closed with removable cover - 1 pair of steel ramps to bridge the lowbed's pick-up hooks - Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm - Wireless remote control for rear steering in addition to cable remote, with signal lights at receiver for single-track monitoring - 6 pairs of threaded blocks between lashing rings under the top chord on the outer beams for mounting screwable RUD rings VLBG-4 - 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading bed - Foldable extensions, approx. 230 mm per side - Loading area features a painted sand layer for anti-slip protection - Dipper stick trough of rear chassis closed at front and rear with plug-in plates - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - alu 15%)

Stanje: rabljeno, lastna masa: 29.600 kg, največja dovoljena obremenitev: 72.400 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, prva registracija: 08/2025, dolžina tovornega prostora: 6.650 mm, širina tovornega prostora: 2.840 mm, višina nakladalnega prostora: 550 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, Leto izdelave: 2025, Oprema: ABS, Gooseneck: - Gooseneck hydraulically liftable/lowerable and detachable - Length approx. 3,650 mm - For tractor units: 6 x 4 or 8 x 4 2-axle front running gear: - Hook attachment front and rear - Frame length x frame width approx. 2,200 mm x 2,850 mm Excavator deck “BB-A”: - Telescopic excavator deck “BB-A” with drive-over bridge hooks at the front and bolt-lug coupling at the rear - Length x base width approx. 6,650 mm x 2,850 mm - Beam height x beam width approx. 400 mm x 1,350 mm - Loading height 550 mm with 150 mm ground clearance 4-axle rear running gear: - Mechanical bolt-lug coupling at the front for mounting a lowbed, end cross-member at the rear - Frame length x frame width approx. 5,480 mm x 2,850 mm Pendulum axle and tires (front and rear running gear): - “PENDEL-AXLE”, all axles hydromechanically force-steered - Burst hose valve on the axle equalization cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and safety pins to secure in raised position - Axles top-coated with 2-layer 2-component paint, single-color MB 7350 Novagrau - Technical axle load: 12,000 kg - Hydraulic axle equalization - Tires 285/70 R19.5 Remote steering: - Remote steering from front and rear, operable by cable remote via push-buttons, with axle alignment monitoring - Socket for operating remote steering at gooseneck - Cable remote with push-buttons including axle alignment monitoring Accessories included: - Galvanized connection bar at the front with yellow-red air couplings - Steel front wall approx. 400 mm high - 4 chocks - 3.5" king pin - One 7-pin socket on left and right rear of gooseneck for warning board - Boom with winch for spare wheel at the front of the gooseneck - Truck hydraulic connection with flow controller (40 l/min), including boom for supply line suspension, tractor unit tank must have at least 80 liters capacity with couplings - Plug-in ALU drop sides and rear wall for gooseneck, approx. 400 mm high, anodized - Operating lever on gooseneck protected by a folding cover - Separate air connection with air gun on the gooseneck - BEKAMAX central lubrication system with standard grease NLGI-2, 1x at gooseneck, 1x at 2-axle running gear, and 1x at 4-axle running gear - Variomax tool kit - Multi-coupling hydraulic connectors at gooseneck and in the area of the lowbed hook attachment - 2 spare wheels - Front running gear with a separate air connection for air impact wrench - Folding extensions with steel floor plates, width adjustable from approx. 2,850 mm to 3,250 mm - Steel plates can be inserted into 2 positions to obtain a lowered loading deck - Steel plates with rubber surface approx. 12 mm thick - Threaded inserts (⌀ 40 mm) every approx. 500 mm outside on the top flange of the excavator deck’s outer tube for screw rings - 2 stainless steel toolboxes approx. 855 x 340 x 390 mm left + right on the gooseneck - Radio remote control for remote steering in addition to cable remote - 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery - Steel plates adjustable in width from 2,850 mm to 3,250 mm and insertable in 2 positions for a lowered loading deck - 4 pairs of steel plates with rubber surface approx. 12 mm thick - Maximum 3,500 mm extendable tube coverable, in 500 mm increments Nwedpfx Ahszauvro Roi - Lowbed central beam provided with a painted-on sand layer as anti-slip protection - Extensive lashing points

Stanje: novo, lastna masa: 15.420 kg, največja dovoljena obremenitev: 61.080 kg, skupna masa: 76.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading Platform: Extendable loading platform with rear chamfer approx. 500 mm x 8° 8 pairs of flip-out lashing rings 1 pair of recessed lashing rings at the front of the loading area Cutouts in the outer frame for securing straps Approx. 48 mm thick hardwood flooring; checker plate above the axles Two-Part Steel Ramps: One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering. Ramps with hydraulically folding ramp sections, hydraulic lifting and hydraulic lateral movement. Max load per pair: 50,000kg. Landing Legs: • JOST landing legs (mechanical) with two-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: BPW axles and suspension, 4th and 5th axle self-steering Technical axle load: 12,000 kg 4th and 5th axle with electromagnetically operated reverse lock, activated by reverse gear and manually Tyres: 235/75 R 17.5 3PMSF Brake System: Brake system according to EU regulations with EBS-E (4S3M) Nsdol Sl Izspfx Ah Rewi Sockets and Lighting: Electrical system according to EU standards, 24 Volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets Connections per ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component (2K) zinc-rich primer High-quality single-colour 2K topcoat in MB 7350 Novagrau Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Steel Structure: High-strength fine-grained steel construction Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Accessories: One spare wheel with holder in front of the front wall 2" king pin Galvanized steel front wall approx. 400 mm high Yellow-red air couplings on the galvanized front connection panel 2 wheel chocks with holder on the front wall Mounting at the rear of the gooseneck for ALU approach ramps Bracket for beacon at trailer rear Galvanized supports under sloped area of load floor White reflective tape per EU regulations on sides, extension, and red at the rear Electro-hydraulic unit under the rear of loading platform Warning sign brackets including sockets left/right on gooseneck and rear plate Control valves for ramps mounted right side of trailer Mudflap at rear of trailer Manual and documentation on USB stick 3.5" loose king pin supplied On gooseneck: ALU side boards and rear wall, plug-in approx. 2,440 x 400 mm (LxH) Removable rear galvanized stakes (Body length approx. 2,560 mm) 3 pairs WADER container pockets for 1x 20'/30' or 1x 40' container 6 pairs stake pockets for 100 x 50 mm plug-in stakes in outer frame Galvanized extensions, extendable by approx. 230 mm per side Lift axle on front axle, controlled via TEBS E according to actual axle load and current payload Square climbing strips 20 x 20 mm every 200 mm on outer frame chamfer of load floor Checker plate coverings above the king pin and loading area...

Stanje: novo, lastna masa: 13.250 kg, največja dovoljena obremenitev: 47.550 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, vzmetenje: zrak, velikost pnevmatike: 245/70 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings 30 mm thick hardwood flooring Extendable loading platform: Loading platform in extendable design with rear chamfer approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings Nwodpjl Uxdkjfx Ah Roi 3 pairs of outward-folding lashing rings 1 pair of flat lashing rings at the front of the loading area Cut-outs in the outer frame of the loading area for inserting tension straps Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Two-part steel ramps: One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering. Ramp with hydraulically folding and unfolding parts, hydraulic lifting system, and hydraulically adjustable position. Maximum load per pair: 40,000 kg Landing legs: JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced-steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool Tires 245/70 R 17.5 Braking system: Braking system according to EU regulations with EBS-E (4S3M) without connecting lines to tractor unit Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer High-quality one-color two-component (2K) top coat in Novagrau Rear section metallized and painted in RAL 9010 (pure white) Metallic paint not possible Electrical system: Electrical system according to EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connections conforming to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" kingpin One galvanized steel headboard approx. 400 mm high At the galvanized front connection strip, yellow-red air couplings 4 wheel chocks with holders at the headboard One spare wheel with holder in front of the headboard Electro-hydraulic power unit Rear and front remote steering via cable remote control with push-buttons, with single-track control of the axles Bracket at rear of gooseneck for ALU drive-on ramps European reflector signs (red-yellow) at trailer rear White reflective tape according to EU regulations at the sides, at the extension, and red at the rear At the gooseneck and on the ramps left and right, each with a holder for warning signs including socket One holder for beacon at trailer rear Galvanized folding supports under the loading platform chamfer Ramp operating valves fitted on the right side of the trailer Cover plates to bridge the gap between ramps and loading platform One mudflap at trailer rear Manual and description on USB stick Central lubrication system BEKAMAX (Pico) with general-purpose grease NLGI-2 and removable pump guard On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm The rear galvanized stakes are removable, superstructure length approx. 2,560 mm One INOX toolbox 1,350 x 400 x 400 on the gooseneck, box covers oil filler cap 4 pairs of WADER container pockets in the loading area for a

Stanje: novo, največja dovoljena obremenitev: 38.100 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.100 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5 3PMSF, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer of approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading platform: 5 pairs of fold-out lashing rings 3 pairs of fold-out lashing rings 1 pair of horizontal lashing rings at the front of the loading area Cut-outs in the outer frame of the loading surface for hooking in tension belts Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Landing legs: JOST landing legs with 2-speed gears for a 24 t lifting capacity Axles and tyres: BPW axles, two axles are fixed, two axles are self-steering, air-suspended, with drum brakes, with lift/lower function The self-steering axles come with an electro-magnetic reverse lock, which is activated via reverse gear or manually Axle toolkit Tyres: 205/65 R17.5 3PMSF Brake system: WABCO brake system according to EU regulations with EBS-E Steel construction: Steel structure made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Electrical equipment: Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK lighting ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component zinc dust primer High-quality single-colour 2-component top coat in MB 7350 Novagrau No metallic paint possible Rear section metallized and painted in RAL 9010 Accessories included: 1 spare wheel 205/65 R 17.5 TPMS tyre pressure monitoring system acc. to ECE R 141 At the galvanized front connection strip yellow-red air couplings 4 wheel chocks with holder on front wall Bracket at rear of gooseneck for ALU access ramps Galvanized folding supports under the chamfer of the loading surface Mount for a revolving beacon at the rear of the trailer Height-adjustable curtain structure Galvanized front wall with a tension mechanism for the sliding curtains Height-adjustable by approx. 400 mm "EDSCHA" brand roof, sliding forward on ALU roof beam profiles, bolted to the front and rear wall In the loading surface, 3 pairs of sliding stakes Superstructure at rear hydraulically extendable to left and right by approx. 750 mm Sliding roof with upward swinging portal carrier Sliding tarp with 700 mm reserve length, with tension straps at intervals of approx. 600 mm Height to top edge of superstructure approx. 3,960 mm Journeys with the sliding roof open are not permitted and will damage the tarp Mounting rail for ALU access ramps at the rear of the vehicle At the gooseneck and at the rear panel left and right, each with a mount for warning signs incl. socket Nwjdpfx Aotphtmjh Rsi A mud flap at the rear of the trailer European reflector plates at the rear of the trailer 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading area Lifting axle on the front axle controlled by TEBS E depending on current axle load and load status Rear structure with closed ALU double-wing doors A sanded, anti-slip paint layer on the checker plates on the gooseneck and on the loading surface BEKAMAX centralized lubrication system with standard grease NLGI-2 and a removable guard around the pump Speed stickers 80 km/h on rear and both sides Load manometer for axle load determination including load chart

Stanje: novo, lastna masa: 34.500 kg, največja dovoljena obremenitev: 106.700 kg, skupna masa: 141.200 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.150 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 580 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, obratovalna teža: 34.500 kg, Oprema: ABS, Gooseneck: - Gooseneck hydraulically lift/lowerable as well as detachable - Length approx. 3,650 mm - Extensive lashing positions - For tractor units: 6 x 4 or 8 x 4 3-Axle Compact Front Bogie: - Hook mounts at front and rear - Chassis length x chassis width approx. 3,560 mm x 2,850 mm - Extensive lashing positions Excavator Deck “BB-A”: - Telescopic excavator deck “BB-A” with drive-over deck hooks at the front and bolted lug coupling at the rear - Length x base width approx. 7,150 mm x 2,850 mm - Beam height x beam width approx. 430 mm x 1,350 mm - Loading height 580 mm with 150 mm ground clearance - 5 pairs of hanging lashing rings (LC 10,600 daN) - 4 pairs of threaded blocks M30 on inner beam for mounting screw-on rings 5-Axle Rear Bogie: - Mechanical bolt-on lug coupling for fitting a lowbed front, rear end traverse - Chassis length x chassis width approx. 6,840 mm x 2,850 mm - Extensive lashing positions Pendulum Axle and Tyres (front and rear bogie): - “PENDEL-AXLE”, all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-plugs for securing in lifted position - Final paint of axles with 2 coats of 2K paint, single-colour in MB 7350 Novagrau - Technical axle load: 14,640 kg (62 km/h) - Hydraulic axle compensation - Axle tools - Tyres 285/70 R19.5 Steering Override: - Remote steering from the front and rear via cable remote control with push buttons, including axle tracking control - Socket for steering control operation on the gooseneck - Cable remote control with push buttons including axle tracking control Nwedpfx Ahswhywfj Rsi Included accessories: - Yellow-red air couplings on galvanised front connection rail - Steel headboard approx. 400 mm high - 4 wheel chocks with holders - 2 spare wheels 285/70 R19.5 - 3.5" kingpin - Gantry with winch for spare wheel at the front side of the gooseneck - Truck hydraulic connection with flow control valve (40 l/min), including gantry for suspension of supply lines, tractor unit tank must be at least 80 litres with couplings - White reflective tape according to EU regulations on sides and extension, red at rear - Plug-in ALU side panels and rear wall on gooseneck, approx. 400 mm high, anodised - Operating lever on gooseneck protected by folding cover - Separate air connection with air pistol on gooseneck - Central lubrication system BEKAMAX with standard grease NLGI-2: 1x on the gooseneck, 1x on 3-axle bogie, 1x on 5-axle bogie - Variomax tool kit - Multi-coupling hydraulic connections in the lowbed hook area - Front bogie with separate air connection for air screwdriver - Threaded inserts (ø 40 mm) every approx. 500 mm on outside of upper flange of excavator deck for screw rings - Folding extensions with steel mats, width adjustable from approx. 2,850 mm to approx. 3,250 mm - Steel mats with rubber covering approx. 12 mm thick - Two INOX toolboxes 855 x 340 x 390 mm - Radio remote control for steering override in addition to cable remote - Painted sand layer as anti-slip measure - 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery

Stanje: rabljeno, največja dovoljena obremenitev: 30.660 kg, skupna masa: 43.000 kg, konfiguracija osi: 2 osi, prva registracija: 03/2024, naslednji pregled (TÜV): 03/2025, Oprema: ABS, Celotno našo ponudbo vozil, vključno z vozili, ki so na voljo takoj ali v kratkem času, najdete na naši spletni strani. Izvleček iz opreme. Celotna oprema na zahtevo. Nosilna ploščad * Nizka nosilna ploščad z osrednjim nosilcem v izvlečni izvedbi * Dolžina približno 6.750 mm * 5 parov zank za pritrditev tovora, z možnostjo obračanja navzven (LC 5.000 daN) * 1 par zank za pritrditev tovora, z možnostjo obračanja navzven (LC 10.000 daN) * 1 par zank za pritrditev tovora, horizontalno nameščenih na zadnji strani nosilne plošče (LC 10.000 daN) * Napajalne cevi so zaščitene in nameščene v osrednjem nosilcu ter se prilagajajo različnim dolžinam nizke nosilne plošči. Vratna prikolica (»gosi«) * Dolžina približno 3.900 mm * Vratna prikolica, hidravlično dvigljiva in spuščana ter izvlečna * Tehnična obremenitev sedla: 23.000 kg Zadnje podvozje * Zadnje podvozje v kratki izvedbi z zaprtim zunanjim okvirjem in valjano jekleno prevleko * Podvozje z bagerjem, zadnja polovica je zaprta za namestitev rezervoarjev za zrak * 2 para zank za pritrditev tovora, z možnostjo obračanja navzven (LC 5.000 daN) * 1 par zank za pritrditev tovora, z možnostjo obračanja navzven (LC 10.000 daN) Osi * Os BPW, hidravlično-mehansko nadzorovana * Tehnična obremenitev osi: 12.000 kg na os * Zračna vzmet z ventilom za dvig in spuščanje * Orodje za osi Pnevmatike * 245/70 R 17.5 3PMSF – izbira proizvajalca * Indeks obremenitve (146/146F) Zavorna naprava * V skladu z zakonodajo EU, s sistemom EBS-E (2S2M) brez povezovalnih cevi do vlečne enote Jeklena konstrukcija * Iz visoko trdnih jekel * Vrste jekla: S355J2+N/S355MC (meja tečenja 355 MPa), S690QL/S700MC (meja tečenja 690 MPa) Barvanje * Kvalitetna 2-komponentna (2K) barva * Končna barva, enobarvna, v RAL 3002, karmin rdeča Vključno z naslednjo dodatno opremo: * 2 palčni kraljevi zatič * Pocinkana jeklena sprednja stena, približno 400 mm visoka * Nosilec za rezervno kolo pred sprednjo steno * Na pocinkani priključni letev spredaj, rumeno-rdeče zračne spojke * 4 kosi klinih s pritrdilnim nosilcem (± 5 kg) * Vodenje zadnje osi, od spredaj in zadaj, prek kabelske daljinske upravljalne enote z gumbi, z nadzorom položaja osi (brez vgradnje v vlečno enoto) * Električno-hidravlična enota (± 45 kg) * Rumeni reflektorski trak v skladu z zakonodajo EU, stransko, na izvlečni plošči in zadaj na prikolici * 1 lesen blok, približno 500x250x200 mm * Držalo za aluminijaste rampe na zadnji strani vozila * Držalo za okroglo luč na zadnji strani prikolice * Blatnik na zadnji strani prikolice * Evropske reflektorske table (rdeče-rumene) na zadnji strani prikolice * Na vratni prikolici in zadnji plošči, na levi in desni strani, držalo za opozorilne table, vključno z vtičnico * Priročnik in opis na USB-ključu * Nalepka za omejitev hitrosti 80 km/h, zadaj in na obeh straneh * Manometer za obremenitev osi, za ugotavljanje obremenitve osi, vključno z diagramom obremenitve Vključno s posebno dodatno opremo * Na vratni prikolici, aluminijaste stranske in zadnje stene, vstavljive, približno 2.440 x 400 mm (D x V) Nwsdpfxszm D Ucs Ah Rji * Zadnji pocinkani vstavni profili so odstranljivi. (Dolžina nadstavka približno 2.560 mm). (± 46 kg) * Na vratni prikolici ločena zračna priključna točka s pištolo za polnjenje z zrakom * 2 delovna reflektorja s stikalom na prikolici, nameščena na podstavku vratne prikolice, na levi in desni strani * 6 parov žepov za vstavne profile, približno 100 x 50 mm, v zunanjem okvirju nosilne plošče * 2 para v zunanjem okvirju podvozja (±

Stanje: rabljeno, največja dovoljena obremenitev: 25.630 kg, skupna masa: 38.000 kg, konfiguracija osi: 2 osi, prva registracija: 11/2024, naslednji pregled (TÜV): 11/2026, Oprema: ABS,

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, lastna masa: 12.900 kg, skupna masa: 49.000 kg, konfiguracija osi: 2 osi, prva registracija: 03/2022, Leto izdelave: 2022, Faymonville 2-axle lowbed semi-trailer MEGAMAX 2x12 t PA 2 steered axles Single-extendable, 2 x 12 t pendle axles Overall length: approx. 13,500 mm Overall width: approx. 2,550 mm Neck width: approx. 2,480 mm Load bed width: approx. 2,550 mm Chassis width: approx. 2,550 mm Technically extendable: approx. 4,700 mm Coupling height (loaded): approx. 1,205 mm Loading height (max. loaded): approx. 1,005 mm Load area length: approx. 6,850 mm Chassis length: approx. 2,600 mm King pin distance to front: approx. 1,200 mm Swing radius of tractor unit (rear): approx. 2,300 mm Swing radius (front): approx. 1,800 mm Axle spacings: approx. 1,360 mm Gooseneck: Nwedpfx Ahjy Hxd Ij Rji - Gooseneck in SNT design for optimized load floor length, length approx. 3,750 mm - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth-wheel load: 25,000 kg Boiler deck: - Deep-designed extendable boiler deck "SUPER LOW" design - Length approx. 6,850 mm, with mechanical locking system Rear chassis: - Rear chassis with closed outer frame, chequer plate and continuous prism digger recess, approx. 1,250/700 x 505 mm, open at the rear - PENDLE-AXLE, all axles hydro-mechanically forced-steered - Burst hose valve on axle compensation cylinder with automated RESET function - Hydraulic cylinders with shut-off cocks and front pins to secure lifted position - Technical axle load: 12,000 kg each - Hydraulic axle levelling Brake system: - WABCO brake system, EBS-E according to regulations Chassis tyres: - 245/70 R 17.5 3PMS Metalizing: - Complete HRM metallization (High Resistance Metallisation) - Entire steel structure shot-blasted, then hot-finished with ZINACOR 850 (Zinc 85%, Alu 15%) Painting: - 6-coat final treatment - Entire steel structure shot-blasted after welding. One layer of zinc-based primer, one adhesion primer. Final coat with 2 layers of 2K lacquer (acrylic) in a single colour, followed by cavity sealing with special wax - Trailer colour: RAL 3002 Carmine Red - Rim colour: Silver Grey - Side board colour: Natural Aluminum Steel structure: - Steel structure made of high-strength fine-grained steels. - Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690Q/S700MC (yield strength 690MPa) - MAG welding process according to EN ISO 4063

Stanje: novo, največja dovoljena obremenitev: 98.290 kg, skupna masa: 126.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, You can find our entire range of vehicles that are immediately and soon available on our website. Extract from the equipment list. Full equipment details available on request. Gooseneck: * MAX810-neck-V-30-2.70-2{DSR 2 700/ASH 1300->1400} * Gooseneck hydraulically liftable/lowerable as well as removable. Length approx. 3,650 mm * Truck hydraulic connection with flow controller (20 l/min), * incl. gallows for suspension of supply lines, tractor unit (SZM) tank must hold at least 80 l, with MAX Trailer coupling pieces; otherwise, coupling pieces to be provided by the customer ex works. * For tractor units: 6 x 4 or 8 x 4 Loading Platform MAX810-6-A-11.00-17.5-1.50-2.75-PA-X * 6-axle extendable loading platform with pin-lug coupling at the front and approx. 500 mm x 8° chamfer at the rear. * Length: approx. 11,000 mm * Technically extendable by: approx. 7,700 mm * Axle spacing: approx. 1,500 mm * Hydraulic coupling bolt. Pendulum axle 2-axle front running gear, pendulum axle * All axles are hydromechanically forced steered. * MAX810-chassis-PA-X-F-2-17.5-1.50-2.75 pin-lug coupling front and rear. * Length: approx. 2,970 mm, chassis width: approx. 2,750 mm * BEKA-MAX central lubrication for a 2-axle running gear with standard grease NLGI-2 * Extendable widenings of approx. 230 mm per side for a 2-axle running gear. (± 27 kg) PENDULUM AXLE 6-AXLE LOADING PLATFORM, PENDULUM AXLE * All axles hydromechanically forced steered. * Hose burst valve on the axle compensation cylinder with automatic reset function. * Hydraulic cylinders with shut-off valves and pre-pin for securing in raised position. * Technical axle load: 13,740 kg each (30 km/h) * Hydraulic axle compensation. TYRES * 24 x manufacturer of our choice (M+S) 245/70 R17.5 * Load index 143/141L (146/146F) * TPMS: TPMS tyre pressure monitoring system in accordance with ECE R 141. Final coating of the axles * Painted with two coats of single-colour 2-component paint in DB7350 nova grey. * PAINTING Complete steel structure automatically blasted with shot blasting system after welding. * Second blast processing with corundum for optimal adhesion of the coating system. * HRM-metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure the best corrosion protection. * PAINTING Trailer carmine red (RAL 3002) Including the following accessories * Gallows with winch for spare wheel at the front of the gooseneck. * 3.5 inch king pin * Steel front wall approx. 400 mm high. * Plug-in ALU side boards and rear wall on the gooseneck, approx. 400 mm high, anodized version. * Control lever on the gooseneck protected by a foldable cover. * Lighting of the controls on the gooseneck with on/off switch. * One 7-pin socket left and right rear on the gooseneck for the warning sign. * Load gauge on the gooseneck for axle load determination on the running gear at front and rear * BEKA-MAX central lubrication for a gooseneck with standard grease NLGI-2. * Hydraulic connections from the gooseneck to the low bed with screw couplings. * Access possibility on the gooseneck. * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery. Output: 9.5 kW (12.9 HP) at 3000 rpm, emission level: EU Stage V, max. hydraulic pressure: 280 bar, max. flow: 21 l/min, installation on the gooseneck. * Hydraulic oil tank 100 L, frame hot-dip galvanized (± 480 kg) * Hydraulic connection lines between powerpack and plug-in plate on the gooseneck. * Radio remote contr Nwodpfx Ajzbfuhsh Rji

Stanje: novo, največja dovoljena obremenitev: 30.190 kg, skupna masa: 43.000 kg, konfiguracija osi: 2 osi, Oprema: ABS, You can find our complete vehicle inventory, including vehicles available for immediate or short-term delivery, on our website. The following is an excerpt from the specifications. Complete equipment details available upon request. Load area: - Lowbed with external beams, extendable version in SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor, approx. 40 mm thick, with mechanical locking - Supply lines are protected within the extendable beams and automatically adjust to the current lowbed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for mounting bolted RUD rings Gooseneck: - Gooseneck in SNT design to optimize load area length, approx. 3,750 mm - Gooseneck hydraulically lift/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2 Rear chassis: - Rear chassis in short version with closed outer frame and checker plate cover - Chassis with excavator recess, closed in the rear half to accommodate air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings lying flat, at the front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced-steered - Technical axle load: 12,000 kg per axle - Air suspension with raise/lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF, manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system according to ECE R 141 - Data transmission to tractor via standardized EBS interface (ISO 11992) - For proper display, the tractor must be capable of transmitting and displaying these data Braking system: - Braking system according to EU regulations with EBS-E (2S2M) Electrical system: - Electrical system in accordance with EU regulations, 24-volt lighting ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with turn indicator - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: - Steel construction of high-strength fine-grain steels - Steel qualities: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Entire steel construction automatically shot-blasted after welding - Second blasting with corundum for optimal coating adhesion - Complete vehicle chassis coated with HRM metallization using ZINACOR 850 (85% zinc / 15% aluminium) for premium corrosion protection - Top coat with 2 layers of 2K paint in RAL 3002 carmine red, single-color, according to RAL system 841GL - Rims in silver - Rear section metallized and painted in RAL 9010 (pure white) - No metallic paint possible - Paint system tested in salt spray test according to ISO 9227-NSS - Cavity sealing with special wax Nwedpfx Ahexarl Nj Rji Including the following additional equipment: - 2-inch kingpin - One galvanized steel front wall, approx. 400 mm high - Remote-steered axles from front and rear via cable control with pushbuttons, with single-track monitoring (without installation in tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupler instead of threaded couplings - Electro-hydraulic power unit - Prepared for installation of bolted container mounts for 1x 20' or 1x 40' container on outer beams - Without container locks

Stanje: novo, največja dovoljena obremenitev: 25.645 kg, skupna masa: 38.000 kg, konfiguracija osi: 2 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Excerpt from the equipment list. Full equipment details available upon request. Loading Platform: - Low-bed with central beam in extendable design, length approx. 6,750 mm - 5 pairs of lashing rings, foldable outwards (LC 5,000 daN) - 1 pair of lashing rings, foldable outwards (LC 10,000 daN) - 1 pair of flush-mount lashing rings at the rear of the loading platform (LC 10,000 daN) Gooseneck: - Gooseneck hydraulically lift/lowerable and detachable Rear Running Gear: - Rear running gear in short version with closed outer frame and tread plate cover - Running gear with excavator trough, trough rear half enclosed for housing air tanks - 2 pairs of lashing rings, foldable outwards (LC 5,000 daN) - 1 pair of lashing rings, foldable outwards (LC 10,000 daN) - 1 pair of flush-mount lashing rings at the rear of the running gear (LC 10,000 daN) Axles: - BPW axles, hydromechanically forced steering - Air suspension with lifting and lowering valve Tyres: - Tyres 245/70 R 17.5 3PMSF - TPMS: tyre pressure monitoring system as per ECE R 141 Brake System: - Wabco braking system in compliance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality 2-component (2K) top coat, single colour RAL 3000 flame red Includes the following additional equipment: - 2 king pins - One galvanised steel front wall, approx. 400 mm high - Remote steering adjustment from front and rear via cable remote control with pushbuttons, including single-track axle alignment (without installation in the tractor unit) Nsdsxf Silspfx Ah Rowi - Electro-hydraulic unit - Axle load gauge including axle load diagram - On the gooseneck, aluminium side boards and rear wall, plug-in type, approx. 2,440 x 400 mm (L x H). The rear galvanised plug-in stanchions are removable. (Upper body length approx. 2,560 mm) - Separate air connection with blow gun on the gooseneck - 2 work lights with switch on the trailer, mounted on left and right sides of the gooseneck platform - One INOX toolbox, approx. 1,350 x 400 x 400 mm, mounted on the gooseneck - 6 pairs of stanchion pockets for plug-in stanchions approx. 100 x 50 mm in the outer frame of the loading platform, 2 pairs in the rear frame of the running gear - Galvanised, extendable load width extensions approx. 230 mm per side - Hydraulic connections from the gooseneck to the low-bed with multi-coupling instead of screw couplings. No guarantee on seals. - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 with removable pump protection - 2 pairs of WADER container pockets in the loading platform, for 1x 20’ container - One removable galvanised intermediate platform with 1 pair of WADER container pockets - 1 pair of steel ramps to bridge over the low-bed’s loading hooks - Loading platform with painted sand layer as anti-slip protection - HRM metallization (High Resistance Metallization)

Stanje: novo, lastna masa: 9.300 kg, največja dovoljena obremenitev: 30.100 kg, skupna masa: 39.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, Oprema: ABS, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm hardwood flooring Extendable loading platform: - Loading platform, extendable execution with rear bevel approx. 1,000 mm x 8° - 5 pairs of folding external lashing rings (LC 5,000 daN) - 3 pairs of folding external lashing rings (LC 10,000 daN) - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - Cutouts in the outer frame of the platform for attaching tie-down straps (LC 2,000 daN) - Hardwood flooring approx. 48 mm thick, over the axles with checker plate covering Landing legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Axles and tyres: - BPW axles, hydro-mechanically forced steering - Technical axle load: 12,000 kg - Air suspension with raise/lower valve - Axle tool kit - TPMS tyre pressure monitoring system according to ECE R 141 - Tyres: 235/75 R17.5 3PMSF Accessories included: Nwedoyxc Eyepfx Ah Roi - 2" kingpin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection strip - 2 wheel chocks with holder on the front wall - One spare wheel with holder in front of the front wall - Electro-hydraulic unit - Rear axle steering, operable from front and rear via cable remote control with push buttons, with axle single-track monitoring - European reflective warning plates (red-yellow) at the rear of the trailer - White reflective tape according to EU regulations on the sides and on the extension, red at the rear - Gooseneck and rear left and right brackets for warning signs, including socket - Sliding hook-in bar for ALU loading ramps at the rear of the vehicle - One bracket for a rotating beacon at the rear of the trailer - Galvanized folding supports under the rear bevel of the loading platform - One mudguard at the rear of the trailer - Operating manual and documentation on USB stick - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and removable pump protection cover - Removable ALU side boards and tailgate on the gooseneck approx. 2,440 x 400 mm - The rear galvanized stanchions are removable (body length approx. 2,560 mm) - 3 pairs of WADER container pockets in the loading platform for 1x 20ft, 1x 30ft or 1x 40ft container - 6 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform - One INOX toolbox 1,500 x 390 x 810 mm under the loading platform, right side in direction of travel - Four warning signs, extendable by approx. 400 mm, approx. 423 x 423 mm with a position light - On the warning signs a bracket for a rotating beacon - Radio remote control for rear axle steering, in addition to cable remote control, with indicator lights on receiver for single-track monitoring - On the checker plate surfaces on the gooseneck and loading platform, a painted sand layer as anti-slip protection - Speed sticker 80 km/h at the rear and on both sides - Axle load gauge for determining axle loads, including load diagram

Stanje: novo, največja dovoljena obremenitev: 39.720 kg, skupna masa: 50.960 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete range of vehicles, including immediately and short-term available units, can be found on our website. Excerpt from the equipment list. Full specification available on request. Gooseneck * With beveled front corners, approx. 45°, and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area * Extendable loading area version * 5 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of lashing rings laid flat at the front of the loading area (LC 10,000 daN) * Cut-outs in the outer frame of the loading area for securing straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Landing legs Nodpfx Aheu Sd U Uj Rswi * JOST (mechanical) with two-speed gearbox, lifting capacity approx. 24 t (test load approx. 50 t) Axles * BPW axles, two fixed, two self-steering, with drum brakes * Air suspension with raise/lower function * Self-steering axle with electromagnetic reverse lock, activated by reverse gear or manually * Tyres: 205/65 R 17.5 Braking system * Wabco braking system meeting EU regulations with EBS-E (4S3M), without interconnection lines to the tractor unit Steel Construction * Made from high-tensile fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Paintwork * First-class, long-lasting corrosion protection for the standard shot-blasted welded frame, ensured by a two-component (2K) zinc dust primer * High-grade, single-color two-component (2K) topcoat in RAL 3002 Carmine Red * Rear section metallized and finished in RAL 9010 (Pure White) * Wheels in silver Accessories included * 2-inch kingpin * Galvanized steel front wall, approx. 400 mm high * Spare wheel holder in front of the front wall * Yellow-red air couplings on galvanized front connection rail * 4 wheel chocks with holder on the front wall * Rear section of the gooseneck with mounting for aluminium ramps * Galvanized folding supports under the rear bevel of the loading area * Bracket for a beacon on the trailer’s rear * Yellow reflective tape on the sides, extension, and rear, in compliance with EU regulations * Holders for warning signs with socket on left and right of gooseneck and rear panel * TPMS tire pressure monitoring system according to ECE R 141. Data transfer to the towing vehicle is via the standardized EBS interface per ISO 11992; for correct display the towing vehicle must be able to receive and display the data * On the gooseneck: clip-on aluminium side and rear panels, approx. 2,440 x 400 mm (L x H); rear galvanized stakes are removable (body length approx. 2,560 mm) * One galvanized toolbox integrated into the beveled gooseneck * 6 pairs of WADER container pockets in loading area, for 1 x 20' container, 2 x 20' containers, or 1 x 40' container * Sliding brackets for aluminium ramps at the vehicle’s rear * 7 pairs of stake pockets for removable stakes, approx. 100 x 50 mm in the outer frame of the loading area * One galvanized transverse holder under the loading area * Galvanized, extendable outriggers for widening by approx. 230 mm per side * Lift axle on the front axle controlled by TEBS E depending on current axle load and loading condition * 5 pairs of recessed lashing rings along the central beam (LC 5,000 daN)

Stanje: rabljeno, lastna masa: 10.600 kg, največja dovoljena obremenitev: 39.400 kg, skupna masa: 50.960 kg, konfiguracija osi: 3 osi, prva registracija: 09/2024, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5, barva: siv, Leto izdelave: 2024, obratovalna teža: 10.600 kg, Oprema: ABS, Vrat: -Vrat z oblogo prevleko iz trdega lesa, debeline 30 mm -Vrat na zadnji strani v ravni izvedbi Nedpfx Ahsw Adkxj Rswi -3 pari zateznih obročev (LC 5.000 daN) Nakladalna površina z izvlečno izvedbo: -Nakladalna površina z izvlečno izvedbo -5 parov zateznih obročev, ki se zunanje odklapljajo (LC 5.000 daN) -3 pari zateznih obročev, ki se zunanje odklapljajo (LC 10.000 daN) -1 par zateznih obročev, nameščen vodoravno spredaj na nakladalni površini (LC 10.000 daN) -Izrezi na zunanjem okvirju nakladalne površine za pritrditev zategovalnih pasov (LC 2.000 daN) -Obloga iz trdega lesa, debeline približno 48 mm; nad osmi je prevleka iz valjane pločevine Podpora sedla: -JOST podpore sedla (mehanske) z 2-stopenjskim menjalnikom za 24 t nosilnosti (5 t testna nosilnost) Osi in pnevmatike: -BPW osi, dve fiksni osi, dve sledilni osi -Zračna vzmet, z bobnasto zavoro, z funkcijo dviganja/spuščanja -Sledilne osi z elektromagnetično blokado za vožnjo v vzvratno smer, ki se aktivira preko vzvratnega prestave ali ročno -Pnevmatike 205/65 R17.5 Zavorna naprava: -Zavorna naprava v skladu z uredbami EU, z EBS-E (4S3M) Jeklena konstrukcija: -Jeklena konstrukcija iz visoko trdnih finozrnatih jekel -Vrste jekel: -S355J2+N/S355MC (meja tečenja 355 MPa) -S690QL/S700MC (meja tečenja 690 MPa) Električna napeljava: -Električna napeljava v skladu z uredbami EU, razsvetljava 24 voltov, ASPÖCK-NORDIK (ASS3) -ASPÖCK-UNIBOX na priključni letvi spredaj s vtičnicami 24N, 24S in 15-polno -Barvanje: -Prvo razredna in dolgotrajna protikorozijska zaščita standardno peskane varjene konstrukcije je zagotovljena z dvokomponentnim (2K) cinkovo-prašnim temeljnim premazom -Visokokakovosten dvokomponentni (2K) končni premaz, enobarvni, v barvi Novagrau Vključena dodatna oprema: -En rezervni zračniški kolo z nosilcem pred čelno steno -2" kraljeviče -En pocinkana jeklena čelna stena, približno 400 mm visoka -Na pocinkani priključni letvi spredaj rumeno-rdeče zračne spojke -4 kosi klinih z nosilcem na čelni steni -Pocinkane zložljive podpore pod poševnino nakladalne površine -Nosilec za rotacijsko luč na zadnji strani prikolice -Podaljški, pocinkani, izvlečni za približno 230 mm na vsaki strani -Bel refleksni trak v skladu z uredbami EU, na strani, na izvlečni površini in zadaj rdeč -Na vratu in na zadnji plošči na levi in desni strani po en nosilec za opozorilne table, vključno z vtičnico -En odbijač blata na zadnji strani prikolice -Evropski odsevni znaki (rdeče-rumeni) na zadnji strani prikolice -Priročnik in navodila na USB pomnilniku -Sistem za nadzor tlaka v pnevmatikah (TPMS) v skladu z ECE R 141 -Na vratu aluminijaste stranske stene in zadnja stena, ki se vstavi, približno 2.440 x 400 mm -Zadnje, pocinkane vstavne ograje so odstranljive, dolžina nadgradnje je približno 2.560 mm -7 parov držal za kontejnerje WADER -1 x 20-čevlni kontejner na nakladalni površini; 1 x 40-čevlni kontejner na nakladalni površini; 1 x 40-čevlni kontejner nad vratom; 2 x 20-čevlni kontejner -7 parov držal za ograje za vstavne ograje 100 x 50 mm na zunanjem okvirju nakladalne površine -Dvižna os na sprednji osi z nadzorom preko TEBS E, odvisno od trenutne obremenitve osi in trenutnega stanja obremenitve -Premikajoča se letva za pritrditev aluminijastih plošč na zadnji strani vozila -Na valjani pločevini na vratu in na nakladalni površini prevleka iz peska kot zaščita pred zdrsom -Štiri opozorilne table, ki se približno za 400 mm izvlečejo, približno 423 x 423 mm, z pozicijsko lučjo -Na opozorilnih tablah nosilec za

Stanje: novo, največja dovoljena obremenitev: 73.540 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, Our complete vehicle inventory, including immediately and short-term available vehicles, can be found on our website. Excerpt from the equipment specification. Full equipment details available upon request. Gooseneck: * Hydraulically liftable/lowerable and detachable gooseneck, length approx. 3,650 mm * 2 pairs of fold-out lashing rings on the exterior (LC 5,000 daN) * 2 pairs of lashing rings on the gooseneck (LC 10,600 daN) * 1 pair of lashing rings in the center of the gooseneck (LC 10,600 daN) * Suitable for tractor units 6 x 4 or 8 x 4, 2-axle Compact front bogie: * Hook coupling front and rear, length approx. 2,200 mm * Bogie width: approx. 2,850 mm Excavator deck: * Telescopic excavator deck with drive-over deck hooks at the front and pin-eye coupling at the rear * Base width: approx. 2,850 mm * Length: approx. 6,650 mm * Beam height: approx. 400 mm * Beam width: approx. 1,350 mm * Loading height approx. 550 mm with ground clearance approx. 150 mm 4-axle rear bogie: * Mechanical pin-eye coupling at the front for connecting a low-bed trailer * Rear end cross member, bogie width: approx. 2,850 mm * Bogie length: approx. 5,480 mm Oscillating axles, all axles hydro-mechanically forced-steered * Technical axle load: 14,640 kg per axle (62 km/h) * Hydraulic axle compensation Tyres: * Front bogie: 8 x (manufacturer’s choice; M+S) 285/70 R19.5 * Rear bogie: 16 x (manufacturer’s choice; M+S) 285/70 R19.5 * Load index 150/148J Paintwork: * Complete steel structure automatically shot-blasted after welding using a turbine blasting unit. Second abrasive blasting with corundum for optimum coating adhesion * Full chassis HRM-metalized with ZINACOR 850 (85% zinc/15% aluminum) for maximum corrosion protection * Final coating in 2 layers of 2-component top coat, single color in RAL 3002 carmine red, according to RAL 841GL system Including the following accessories: * Steel front wall, approx. 400 mm high * Plug-in ALU side panels and rear wall on the gooseneck, approx. 400 mm high, anodized finish * 3.5-inch kingpin * Truck hydraulic connection with flow controller (20 l/min) * Overhead support for supply lines; tractor unit tank must hold at least 80 l * With MAX Trailer coupling pieces; otherwise, couplings to be supplied by the customer ex works * BEKA-MAX centralized lubrication for gooseneck with standard grease NLGI-2 * Tool kit Art No. 612452 Nedpfsxbmplsx Ah Rswi * Multi-coupling hydraulic connections on the gooseneck * Front bogie with separate air connection for air-powered tools * BEKA-MAX centralized lubrication for 2-axle bogie with standard grease NLGI-2 * One 7-pin socket each left and right at the rear of the front bogie for warning panels * Threading option (ø approx. 40 mm) every approx. 500 mm on the outside of the top flange of the excavator deck outer tube for screw rings (LC 16,000 daN) * Foldable extensions with steel mats, width adjustable from approx. 2,850 mm to approx. 3,250 mm * BEKA-MAX centralized lubrication for 4-axle bogie with standard grease NLGI-2 * Socket on the rear bogie for cable remote control of rear steering * Rear bogie with trough * Two stainless steel toolboxes, approx. 855 x 340 x 390 mm, mounted on the gooseneck left and right * Single-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery * Radio remote control: * Operation of the power pack, start/stop of the diesel engine * Operation of the rear steering, in addition to cable remote control * One LED work spotlight each left and

Stanje: novo, lastna masa: 9.600 kg, največja dovoljena obremenitev: 53.400 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 12.400 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.340 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22.5, barva: siv, Oprema: ABS, Platform area: - Platform with approx. 30 mm thick hardwood flooring - 10 pairs of folding lash rings (outward folding) Landing legs: - JOST landing legs with 2-speed gearbox, 24 t lifting capacity Axles and tyres: - BPW axles, technical capacity 10,000 kg per axle; first axle fixed, all other axles hydro-mechanically forced-steered, mounted on turntables - Air suspension with raise/lower valve - Axle tools included - Tyres: 385/65 R22.5 Braking system: - WABCO brake system in accordance with EU regulations, with EBS-E (4S3M) Steel construction: - Steel structure made from high-tensile fine-grained steels - Steel grades: - S355J2+N / S355MC - S690QL / S700MC Electrical system: - Electrical system according to EU regulations, 24 Volt lighting - ASPÖCK-UNIBOX on the front connection rail with 24N, 24S and 15-pin sockets - Connections according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - First-class and durable corrosion protection of the standard shot-blasted welded frame is ensured by a 2-component zinc-dust primer - High-quality 2-component topcoat, single-colour in Nova Grey - Rear section metallized and painted in RAL 9010 Accessories included: - Platform with approx. 30 mm thick hardwood flooring - 2" king pin - One galvanized steel front wall approx. 1,200 mm high, EN12642-XL - Yellow-red air couplings at the galvanized connection rail at the front - 4 wheel chocks with holders on the front wall - Storage for 1,000 mm plug-in stanchions in the rear central beam - On the gooseneck and rear panel, left and right, a mounting bracket for warning signs with socket - Remote steering from front and rear, operated via cable remote control with push-buttons; with axle tracking control - Electro-hydraulic power pack - White reflective tape as per EU regulations along the side of the trailer, red at rear - 12 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the load bed - European reflective plates at the trailer rear - One bracket for a rotary beacon at the rear of the trailer - One mudflap at the trailer rear - Manual and documentation on USB stick - Central lubrication system BEKAMAX (Pico) with standard NLGI-2 grease and removable protector for the pump - TPMS tyre pressure monitoring system: - The towing vehicle must be capable of transmitting and displaying these data for correct readout - Lift axle on the front axle, automatically controlled by TEBS E in accordance with current axle load and trailer loading status - Radio remote control for the remote steering in addition to the cable remote, with indicator lamps on the receiver for axle tracking control - 5 pairs of crosswise stanchion pocket strips on the bed for 100 x 50 mm plug-in stanchions - 80 km/h speed stickers at rear and both sides - Adjustable access ladder mounted left and right in direction of travel Nwodpjrq Dlfjfx Ah Rji - 2 reversing lights mounted at the rear panel - Load gauge for determining axle loads, including load diagram - HRM metallization of the outer frame: complete steel structure shot-blasted, then all designated visible areas hot metalized with ZINACOR 850 (Zinc 85% - Aluminum 15%)

Stanje: novo, lastna masa: 10.700 kg, največja dovoljena obremenitev: 38.800 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17,5, barva: sivo-črna, Oprema: ABS, Gooseneck: • Gooseneck with front corners beveled at 45° and rear taper approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Extendable loading platform: • Loading platform in extendable design with rear taper approx. 1,000 mm x 8° • Cut-outs in outer frame of loading platform for attaching tensioning straps • Approx. 48 mm thick hardwood flooring; anti-slip checker plate covering above the axles Two-piece steel ramps: • One pair of galvanized, two-piece steel ramps with approx. 48 mm thick hardwood covering • Ramps with hydraulically foldable ramp sections, hydraulic lift system, and hydraulically adjustable • Maximum load per pair: approx. 40,000 kg Axles and tires: • BPW axles and suspension, 2 rigid axles, 1 self-steering axle • Technical axle load: 12,000 kg • Electromagnetic reverse lock, activated via reverse gear or manually • Air suspension with lift and lower valve • Axle tools • 235/75 R 17.5 3PMSF Braking system: • WABCO braking system according to EU regulations with EBS-E Paintwork: • First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component zinc dust primer • High-quality, single-color top coat in MB 7350 Novagrey applied with two-component paint • Rear section metallized and painted in RAL 9010 Landing legs: • JOST landing legs with 2-speed gearbox for 24t lifting load (50t test load) Steel construction: • Steel construction made of high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC • S690QL/S700MC Electrical system: • Electrical system in accordance with EU regulations, 24 Volt lighting • ASPÖCK-UNIBOX on front connection panel with 24N, 24S & 15-pin sockets Accessories included: • One spare wheel with holder • Galvanized steel front wall approx. 400 mm high • Yellow-red air couplings on the galvanized front connection panel • 4 wheel chocks • Rear mounting bracket for beacon light at the end of the semitrailer • Recess at rear of gooseneck for ALU approach ramps • Galvanized folding supports under the loading platform taper • Cover plates to bridge the gap between ramps and loading platform • White reflector tape per EU regulations on sides, extension, and red at rear • Electro-hydraulic unit at rear, under the loading platform • On gooseneck and ramps, left and right, each with a holder for warning signs, including socket Nwjdpfx Ahohlz S Ns Rei • Operating valves for the ramps located on the right side of the trailer • ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) • Four warning panels extendable by approx. 400 mm with a position light • 3 pairs of WADER container pockets in the loading platform for one 20ft, 30ft or 40ft container • 6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading platform • Galvanized extensions, extendable by approx. 230 mm per side • 20 x 20 mm square climbing strips every 200 mm on the outer frame of the platform taper • Painted anti-slip sand layer on checker plates, above king pin and loading platform • Load gauge for axle load measurement, including load diagram • HRM metallization (High Resistance Metallisation) of the outer frame • Complete steel construction shot-blasted, then defined visible surfaces metallized and hot-finished with ZINACOR 850 (Zinc 85% - Alu 15%)

Stanje: novo, lastna masa: 11.000 kg, največja dovoljena obremenitev: 38.500 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm hardwood flooring Load Area: - Extendable loading area with rear taper approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses fitted with square climbing strips 15 x 15 mm, including lower extensions - Between the 1st and 2nd axle, a pair of fixed wheel recesses with cover, approx. 1,610 x 970 x 400 mm - Recess in the bevel as well as protruding into the loading area for parking excavator dipper stick approx. 2,900 x 750 x 210/290 mm - 1 pair of lashing rings, installed flat at the front of the load area (LC 10,000 daN) - 5 pairs of folding lashing rings on the outside (LC 5,000 daN) - 2 pairs of folding lashing rings on the outside (LC 10,000 daN) - 2 pairs of lashing rings in the dipper stick recess (LC 5,000 daN) - Cut-outs in the outer frame of the load area for securing straps (LC 2,000 daN) - Incl. three-part removable galvanized covers over the wheel recesses – max. point load 3.5 t / pc. Two-piece Steel Ramps: - One pair of galvanized, two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood surfacing - Ramp with hydraulically folding ramp sections, hydraulic lifting gear, and hydraulically adjustable Axles and Tyres: Nsdpfx Aeup U Hzeh Rswi - BPW axles and suspension, 2 rigid axles, 1 steering trailing axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lifting and lowering valve - Axle tool kit - Tyres 235/75 R 17.5 - TPMS tyre pressure monitoring system in accordance with ECE R 141 Accessories Included: - Mounts for warning signs left and right at the gooseneck and at the rear, each with socket - One spare wheel - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings at the galvanized front connector strip - 4 wheel chocks - Galvanized, extendable outriggers approx. 230 mm per side - Galvanized folding supports beneath the loading area bevel - Rear trailer bracket for rotating beacon - Cover plates for bridging the gap between ramps and load area - White reflective tape to EU regulations, sides and on extensions; rear in red - Electro-hydraulic unit installed at the rear beneath the loading area - Ramp control valves mounted on right trailer side - European reflective panels (red-yellow) on rear of trailer - Four extendable warning boards, approx. 423 x 423 mm, with position light - Bracket for rotating beacon on warning boards - Removable ALU side boards and rear board on gooseneck approx. 2,440 x 400 mm - Rear galvanized removable stakes (structure length approx. 2,560 mm) - 2 pairs of WADER container pockets in loading area for 20ft or 30ft container - 3 pairs of socket pockets for stakes 100 x 50 mm in outer frame of loading area - Removable, galvanized intermediate table with 1 pair of WADER container pockets - Square climbing strips 20 x 20 mm spaced every 200 mm on outer frame at loading bevelling - Painted sand layer on chequer plates of the gooseneck and loading area for anti-slip protection - 80 km/h speed stickers rear and both sides - Load manometer for axle load measurement, including load chart.

Stanje: novo, lastna masa: 29.600 kg, največja dovoljena obremenitev: 72.400 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 6.650 mm, širina tovornega prostora: 2.840 mm, višina nakladalnega prostora: 550 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, obratovalna teža: 29.600 kg, Oprema: ABS, Gooseneck: - Gooseneck hydraulically liftable/lowerable and detachable Nwedewcmhaspfx Ah Rsi - Length approx. 3,650 mm - For tractor units: 6 x 4 or 8 x 4 2-axle front bogie: - Hook mountings at front and rear - Bogie length x width approx. 2,200 mm x 2,850 mm Excavator deck "BB-A": - Telescopic excavator deck "BB-A" with drive-over bridge hooks at the front and pin-lug coupling at the rear - Length x base width approx. 6,650 mm x 2,850 mm - Beam height x beam width approx. 400 mm x 1,350 mm - Loading height 550 mm with 150 mm ground clearance 4-axle rear bogie: - Mechanical pin-lug coupling for the installation of a lowbed at the front, rear crossmember at the back - Bogie length x width approx. 5,480 mm x 2,850 mm - Multiple lashing points Pendulum axles and tyres (front and rear bogies): - "PENDULUM AXLE", all axles forced-steered via hydromechanics - Hose rupture valve on axle compensation cylinders with automatic RESET function - Hydraulic cylinders with shut-off valves and locking clips for securing in raised position - Final coating on axles: 2 layers of single-colour MB 7350 Novagrau 2K paint - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres size 285/70 R19.5 Remote steering (after-steering): - Remote steering operable from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Socket for remote steering control on gooseneck - Cable remote control with pushbuttons and single-track control included Accessories included: - Yellow and red air couplings on the galvanised front connection bar - Steel front wall approx. 400 mm high - 4 wheel chocks - 3.5" king pin - One 7-pin socket left and right at rear of gooseneck for warning boards - Hoisting jib with winch for spare wheel at the front face of the gooseneck - Truck hydraulic connection with flow control (40 l/min), including support jib for supply lines; tractor unit tank must have at least 80 litres capacity with couplings - Plug-in ALU side and rear boards on gooseneck, approx. 400 mm high, anodised - Control lever on gooseneck protected by foldable cover - Separate air connection with air gun on gooseneck - BEKAMAX central lubrication system: 1x on gooseneck, 1x on 2-axle and 1x on 4-axle bogie - Variomax tool kit - Multi-coupling hydraulic connectors on gooseneck and at lowbed hook interface - 2 spare wheels - One 7-pin socket left and right, at front and rear of rear bogie for warning boards - Front bogie with separate air connection for impact wrench - Foldable steel bed extensions, adjustable in width from approx. 2,850 mm to 3,250 mm - Steel bed inserts can be placed in 2 positions for sunken load area - Steel mats with rubber flooring, approx. 12 mm thick - Thread-in options (⌀ 40 mm) every approx. 500 mm on the upper flange of the excavator deck outer tube for eye bolts - One locking point at every approx. 500 mm on extension with mechanical lock - Socket on rear bogie for remote steering cable control - 2 reversing lights on rear panel - Four extendable warning boards (by approx. 2,000 mm), each approx. 423 x 423 mm with position lights - 1 work light left + right on rear panel of gooseneck with separate on/off switches - Two INOX toolboxes, approx. 855 x 340 x 390 mm - 1-cylinder Hatz diesel engine (Silent Pack) - Radio remote control for after-steering

Stanje: novo, lastna masa: 17.250 kg, največja dovoljena obremenitev: 48.700 kg, skupna masa: 66.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 375 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 17.250 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize loading platform length, approximately 3,750 mm long - Gooseneck hydraulically liftable, lowerable, and detachable - For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Lowbed: - Lowbed with external beams, designed as a telescopic vessel bridge in low-profile construction with front extension - Length x width approx. 7,550 mm x 2,740 mm - Mechanical locking of the extension Chassis: - Rear chassis with closed outer frame - Checker plate surface and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, Suspension, and Tyres: - “PENDEL-AXLE”, all axles hydromechanically forced steered - Burst protection valve on the axle compensation cylinders with automatic reset function - Hydraulic cylinders with shut-off valves and plug pins for securing in raised position - Final coating of axles: two coats of single-color 2-component paint in "FAY-Grey-34-0260" - Technical axle load 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 Accessories: - Detachable steel front wall, approx. 400 mm high - 4 wheel chocks - Rear upper gooseneck area closed with removable cover - 1 pair of steel ramps with climbing bars and locking bolts to bridge the lowbed mounting hooks - Ramps can be positioned over or between the hooks - Mounting options for steel drive-on ramps at the rear, between the outer beams of the gooseneck - Locking point approx. every 1,000 mm on the extension - 1 lashing ring each, left and right, on the front cross member - Supply line connection strip for tractor unit, mounted at the height of outer frame profile - 6 pairs of threaded blocks on the exterior of the load floor inner beams for attaching M24 screw rings - 6 pairs of recessed lashing rings on the outside of the load floor outer beams, foldable inwards and outwards - 1 pair of threaded blocks on the front and rear of the load floor outer beams for M24 screw rings - Mounting rail for loose aluminum approach ramps on the end cross member of the vehicle - Central lubrication system with 2 pumps, brand BEKAMAX - Remote steering front and rear, cable remote controlled, with axle tracking control - 3 kW electro-hydraulic power unit for hydraulic operations, except hydraulic winches - Removable galvanized loading floor, can be placed in 3 elements between the outer beams, with hardwood covering - Foldable extensions, approx. 230 mm per side - Loose extension boards, steel-edged - 4 warning signs approx. 423 x 423 mm - Radio remote control for rear steering - 3.5” kingpin - Anti-slip coating on the left chamfer of the gooseneck - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Guide plate from gooseneck for the fifth wheel plate, approx. 800 mm wide Nedpfx Ajh Hm Tzeh Rowi - 1 spare wheel with mounting adapter - Parking position on the gooseneck for warning signs when not in use - 2 pairs of stake pockets integrated into the chassis outer frame, for plug-in stakes approx. 100 x 50 mm - Excavator stick trough of rear chassis closed at the rear with a removable plate - Trailer color: Mercedes-Benz 7350 Novagrey

Stanje: novo, največja dovoljena obremenitev: 49.000 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with front corners chamfered at 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Extendable Loading Platform: - Loading platform, extendable design with rear chamfer of approx. 1,000 mm x 8° - 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) - 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - 1 pair of horizontal lashing rings at the front of the loading platform (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for securing straps (LC 2,000 daN) - Hardwood flooring approx. 48 mm thick, checker-plate covering above the axles Two-Part Removable Ramps: - One pair of galvanized two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp sections, hydraulic lifting mechanism, and hydraulic side-shift - Maximum load per pair: 40,000 kg Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Axles and Tyres: - BPW axles, two fixed axles and two steering axles (self-steering), air suspended, with drum brakes, raise/lower function - Self-steering axles with electro-magnetic reverse lock, can be activated by reverse gear or manually - Axle tool kit - Tyre size 235/75 R 17.5 Brake System: - Braking system according to EU regulations with EBS-E (4S3M) Steel Structure: - Steel structure made of high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Paintwork: - First-class, long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component (2K) zinc dust primer - High-quality single-tone topcoat using 2-component (2K) paint in Nova grey Electrical System: - Electrical system according to EU regulations, 24 volt lighting, ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX on the front connector strip with 24N, 24S, and 15-pin sockets Included Accessories: - 2" kingpin - Galvanized steel front wall, approx. 400 mm high - One spare wheel with holder in front of the headboard - Yellow-red air couplings on the galvanized front connector strip - 4 wheel chocks with holders on the front wall - Mount at the rear section of the gooseneck for ALU approach ramps - Galvanized folding supports underneath the loading platform chamfer - One holder for warning beacon - Cover plates to bridge the gap between ramps and loading platform - White reflective tape on the side, red on extension and rear, according to EU regulations - Electro-hydraulic power unit - At the gooseneck and ramps (left/right) a holder each for warning signs including socket - Control valves for the ramps mounted on the right side of the trailer - One mud flap at the rear of the trailer - Manual and documentation on USB stick - On the gooseneck, plug-in ALU side boards and rear wall approx. 2,440 x 400 mm - Rear galvanized plug-in stakes are removable (body length approx. 2,560 mm) Nwedpfx Aheh Etf Ro Rei - 4 pairs of WADER container pockets in the loading platform for one 20ft, two 20ft or one 40ft container - 7 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading platform - Galvanized, extendable platform wideners approx. 230 mm per side - Lift axle on the front axle with control system - 20 x 20 mm square climbing bars - BEKAMAX central lubrication system - Four warning signs extendable by approx. 400 mm eac

Stanje: novo, lastna masa: 10.600 kg, največja dovoljena obremenitev: 39.400 kg, skupna masa: 50.960 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5, barva: siv, obratovalna teža: 10.600 kg, Oprema: ABS, Gooseneck: - Gooseneck with 30 mm hardwood flooring - Gooseneck at rear in straight version - 3 pairs of lashing rings (LC 5,000 daN) Extendable load floor: - Load floor in extendable configuration - 5 pairs of lashing rings foldable outward - 3 pairs of lashing rings foldable outward - 1 pair of lashing rings laying at the front end of the load floor - Cut-outs in the outer frame of the load floor for attaching tension straps - Approx. 48 mm hardwood flooring, checker plate covering above the axles Landing legs: - JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tyres: - BPW axles, two rigid axles, two self-steering axles - Air suspension with drum brakes, with lift/lower function - The self-steering axles are equipped with an electromagnetically operated reverse lock, which can be activated via reverse gear or manually - Axle tools - Tyres 205/65 R17.5 Brake system: - Brake system compliant with EU regulations with EBS-E (4S3M) Steel structure: - Steel construction made from high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system in accordance with EU regulations, lighting 24 Volt, ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets - Connections according to ISO: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Paintwork: - High-quality and durable corrosion protection on the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer - High-quality single-colour 2-component (2K) top coat in Novagrau - Rear section metallised and painted in RAL 9010 (Pure White) Included accessories: - One spare wheel with holder in front of the bulkhead - 2" king pin - Galvanised steel front wall approx. 400 mm high Njdpjt Ag Uwefx Ah Rewi - Yellow-red air couplings on the galvanised connection bar at the front - 4 wheel chocks with holder at the front wall - Galvanised folding supports under the load floor slope - Holder for a warning beacon at the rear of the trailer - Galvanised extensions, extendable by approx. 230 mm per side - White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear - On the gooseneck and rear panel, left and right, one bracket each for warning panels including socket - European reflective markings (red-yellow) at the rear of the trailer - TPMS tyre pressure monitoring system according to ECE R 141 - On the gooseneck, plug-in ALU side walls and rear wall, approx. 2,440 x 400 mm - The rear, galvanised plug-in side stanchions are removable, length of the body approx. 2,560 mm - 7 pairs of WADER container pockets - 1x 20ft container on the load floor; 1x 40ft container on the load floor; 1x 40ft container above the gooseneck; 2x 20ft container - 7 pairs of stanchion sockets for plug-in stanchions 100 x 50 mm in the outer frame of the load floor - Lift axle on the front axle with control via TEBS E, depending on the current axle load and load condition - Sliding plug-in rail for ALU loading ramps at the rear of the vehicle - Anti-slip sand finish painted on the checker plates on the gooseneck and load floor - Four warning boards extendable by approx. 400 mm, approx. 423 x 423 mm, each with a position lamp - Holder for warning beacon on the warning boards - 80 km/h speed stickers at the rear and on both sides - Axle load gauge for determination of axle loads inclu

Stanje: novo, lastna masa: 9.300 kg, največja dovoljena obremenitev: 38.700 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.200 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R 22,5, barva: sivo-črna, Oprema: ABS, Cargo Area: • Extendable cargo area with pneumatically operated locking mechanism • Cargo platform with approx. 30 mm thick timber flooring • 7 pairs of external folding lashing rings (LC 5,000 daN) • 3 pairs of external folding lashing rings (LC 10,000 daN) • Cutouts in the outer frame of the cargo area for attaching tensioning straps (LC 2,000 daN) Axles and Tyres: • BPW axles and suspension, all axles hydromechanically forced-steered • Equipped with disc brakes • Technical axle load: 10,000 kg • Air suspension with lift and lower valve • Axle tool kit • Tyres: 385/65 R 22.5 • TPMS tire pressure monitoring system compliant with ECE R 141 Brake System: • WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Electrical System: • Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) • ASPÖCK-UNIBOX at the front control strip with 24N, 24S & 15-pin sockets • Connections as per ISO standards • 24N ISO-1185 Njdpfoiu Etrex Ah Rswi • 24S ISO-3731 • 15-pin ISO-12098 Standard Accessories Included: • Remote-controlled steering from front and rear via cable remote control with push buttons, including single-track axle monitoring • 4 wheel chocks with holders mounted on the front wall • 2" king pin • One galvanized steel front wall, approx. 1,600 mm high • Yellow-red air couplings at the galvanized front connection strip • White reflective tape compliant with EU standards on both sides, on extension, and at the rear of the trailer in red • European reflective plates (red-yellow) at the rear of the trailer • One mud flap at the rear of the trailer • Operating manual and instructions • Mount for a revolving beacon at the rear of the trailer • Cargo area with approx. 30 mm thick timber floor inset in omega profiles • 10 pairs of stake pockets (100 x 50 mm) in the outer frame of the cargo bed • 1 spare wheel holder under the cargo area, right-hand side in the direction of travel • Electro-hydraulic unit • At the gooseneck and rear panel left/right, each with bracket for warning signs, incl. socket • Coated sand layer on the main beam as anti-slip protection • 6 pairs of WADER container pockets in the cargo area for 1x20ft, 2x20ft or 1x40ft containers; additional locking point provided in the extension for a 45ft container • 4 pairs of transverse stake pocket rails in the cargo area for plug-in stakes 100 x 50 mm • Access ladder mounted on the right side in the direction of travel • One HDPE toolbox approx. 1,200 x 500 x 480 mm at the front under the cargo bed, left in the direction of travel • BEKAMAX (Pico) centralized lubrication system with removable pump guard • Lift axle on front axle, controlled via TEBS E according to dynamic axle load and load status • Wireless remote control for steering, in addition to cable operation, with indicator lights on receiver for single-track monitoring • Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm, equipped with position light • Bracket for revolving beacon on the warning signs • 80 km/h speed sticker on rear and both sides • Load gauge for axle load determination, including load chart • HRM (High Resistance Metallisation) of the outer frame • Complete steel construction shot blasted; subsequently, defined visible surfaces metallised by hot-dip application with ZINACOR 850 (85% zinc – 15% aluminium)