Faymonville 3-Achs-Tiefbett 3X10 T Außenträger nakup rabljenega (65.618)

Stanje: novo, skupna masa: 78.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 850 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck in SNT design to optimize loading area length, approx. 3,700 mm long, rear with a bevel approx. 1,000 mm x 10° • For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading Area: • Extendable loading platform, approx. 8,800 mm long with rear bevel approx. 500 mm x 10° • A recess in the platform and rear bevel to accommodate the excavator dipper stick, approx. 3,950 x 580 x 370/450 mm Ramps: • One pair of two-piece steel ramps, approx. 4,350 mm long and 900 mm wide • Hydraulically folding ramp tips • Ramps hydraulically adjustable separately approx. 235 mm outwards and approx. 215 mm inwards • Hardwood decking on the beveled part of the loading area • Ramp with hardwood decking • 20 x 30 mm square climbing strips, approx. every 200 mm on the outer frame of the ramp Axles and Tyres: • TWINAXLE-II independent wheel suspension with BPW stub axles, 1st axle steered in advance, all other axles are hydromechanically forced steered • 1st axle with electromagnetic reverse lock via reverse gear and manual activation • Technical axle load: 12,000 kg Blodpjrvw U Sefx An Tjl • Hydr. axle compensation, hydraulic cylinders with shut-off valves • Tyres 245/70 R 17.5 • TPMS tyre pressure monitoring system according to ECE R 141 Accessories Included: • Plug-in steel front wall, approx. 400 mm high • 4 wheel chocks with holder • Front connection bar with yellow-red air couplings • 3 kW electro-hydraulic power pack for hydraulic control, except for hydraulic winches • 1 spare wheel • 2 pairs of screw-in lashing rings • 1 pair of horizontal lashing rings in the rear area of the gooseneck • On the gooseneck: 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized • On the gooseneck: 1 plug-in ALU rear board, approx. 400 mm high, anodized • Approx. 40 mm thick hardwood decking on the gooseneck, checker plate over the king pin • 3.5" king pin • Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide • Load area locking with conically welded arresting profiles every 250 mm • Incl. pre-tensioning plate • 1 pair of lashing rings on the front cross member • 8 pairs of recessed, fold-out lashing rings in the outer frame of the platform • Extendable (galvanized) widenings approx. 230 mm per side • 1 pair of fixed open wheel recesses up to extension, approx. 700 x 410 mm, in the platform in front of the 1st axle • Wheel recesses with checker plate covering and 15 x 15 mm square climbing strips, approx. every 200 mm • 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm, in the platform between the 1st and 2nd axle • Wheel recesses with 15 x 15 mm square climbing strips and widenings in the lower section • ALU covers for the wheel recesses between 1st and 2nd axle, which can also be used as broadening planks • 1 pair of mechanical rear supports • 20 x 30 mm square climbing strips, approx. every 200 mm on the outer frame of the bevel of the loading area • Central lubrication system with 1 pump, BEKAMAX brand, standard grease as per NLGI-2 • Radio and cable remote control, with 2 indicator lights on the receiver for single wheel control • WABCO Smart Board system • The Smart Board is equipped with an odometer • 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and mounts for rotating beacon

Stanje: novo, lastna masa: 15.420 kg, največja dovoljena obremenitev: 61.080 kg, skupna masa: 76.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading Platform: Extendable loading platform with rear chamfer approx. 500 mm x 8° 8 pairs of flip-out lashing rings 1 pair of recessed lashing rings at the front of the loading area Cutouts in the outer frame for securing straps Approx. 48 mm thick hardwood flooring; checker plate above the axles Two-Part Steel Ramps: One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering. Ramps with hydraulically folding ramp sections, hydraulic lifting and hydraulic lateral movement. Max load per pair: 50,000kg. Bedpfx Aol Sl Izjn Tjll Landing Legs: • JOST landing legs (mechanical) with two-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: BPW axles and suspension, 4th and 5th axle self-steering Technical axle load: 12,000 kg 4th and 5th axle with electromagnetically operated reverse lock, activated by reverse gear and manually Tyres: 235/75 R 17.5 3PMSF Brake System: Brake system according to EU regulations with EBS-E (4S3M) Sockets and Lighting: Electrical system according to EU standards, 24 Volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets Connections per ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component (2K) zinc-rich primer High-quality single-colour 2K topcoat in MB 7350 Novagrau Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Steel Structure: High-strength fine-grained steel construction Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Accessories: One spare wheel with holder in front of the front wall 2" king pin Galvanized steel front wall approx. 400 mm high Yellow-red air couplings on the galvanized front connection panel 2 wheel chocks with holder on the front wall Mounting at the rear of the gooseneck for ALU approach ramps Bracket for beacon at trailer rear Galvanized supports under sloped area of load floor White reflective tape per EU regulations on sides, extension, and red at the rear Electro-hydraulic unit under the rear of loading platform Warning sign brackets including sockets left/right on gooseneck and rear plate Control valves for ramps mounted right side of trailer Mudflap at rear of trailer Manual and documentation on USB stick 3.5" loose king pin supplied On gooseneck: ALU side boards and rear wall, plug-in approx. 2,440 x 400 mm (LxH) Removable rear galvanized stakes (Body length approx. 2,560 mm) 3 pairs WADER container pockets for 1x 20'/30' or 1x 40' container 6 pairs stake pockets for 100 x 50 mm plug-in stakes in outer frame Galvanized extensions, extendable by approx. 230 mm per side Lift axle on front axle, controlled via TEBS E according to actual axle load and current payload Square climbing strips 20 x 20 mm every 200 mm on outer frame chamfer of load floor Checker plate coverings above the king pin and loading area...

Stanje: novo, lastna masa: 9.600 kg, največja dovoljena obremenitev: 53.400 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 12.400 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.340 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22.5, barva: siv, Oprema: ABS, Platform area: - Platform with approx. 30 mm thick hardwood flooring - 10 pairs of folding lash rings (outward folding) Landing legs: - JOST landing legs with 2-speed gearbox, 24 t lifting capacity Axles and tyres: - BPW axles, technical capacity 10,000 kg per axle; first axle fixed, all other axles hydro-mechanically forced-steered, mounted on turntables - Air suspension with raise/lower valve - Axle tools included - Tyres: 385/65 R22.5 Braking system: - WABCO brake system in accordance with EU regulations, with EBS-E (4S3M) Steel construction: - Steel structure made from high-tensile fine-grained steels - Steel grades: - S355J2+N / S355MC - S690QL / S700MC Bsdpfx Aerq Dlfsn Tsll Electrical system: - Electrical system according to EU regulations, 24 Volt lighting - ASPÖCK-UNIBOX on the front connection rail with 24N, 24S and 15-pin sockets - Connections according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - First-class and durable corrosion protection of the standard shot-blasted welded frame is ensured by a 2-component zinc-dust primer - High-quality 2-component topcoat, single-colour in Nova Grey - Rear section metallized and painted in RAL 9010 Accessories included: - Platform with approx. 30 mm thick hardwood flooring - 2" king pin - One galvanized steel front wall approx. 1,200 mm high, EN12642-XL - Yellow-red air couplings at the galvanized connection rail at the front - 4 wheel chocks with holders on the front wall - Storage for 1,000 mm plug-in stanchions in the rear central beam - On the gooseneck and rear panel, left and right, a mounting bracket for warning signs with socket - Remote steering from front and rear, operated via cable remote control with push-buttons; with axle tracking control - Electro-hydraulic power pack - White reflective tape as per EU regulations along the side of the trailer, red at rear - 12 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the load bed - European reflective plates at the trailer rear - One bracket for a rotary beacon at the rear of the trailer - One mudflap at the trailer rear - Manual and documentation on USB stick - Central lubrication system BEKAMAX (Pico) with standard NLGI-2 grease and removable protector for the pump - TPMS tyre pressure monitoring system: - The towing vehicle must be capable of transmitting and displaying these data for correct readout - Lift axle on the front axle, automatically controlled by TEBS E in accordance with current axle load and trailer loading status - Radio remote control for the remote steering in addition to the cable remote, with indicator lamps on the receiver for axle tracking control - 5 pairs of crosswise stanchion pocket strips on the bed for 100 x 50 mm plug-in stanchions - 80 km/h speed stickers at rear and both sides - Adjustable access ladder mounted left and right in direction of travel - 2 reversing lights mounted at the rear panel - Load gauge for determining axle loads, including load diagram - HRM metallization of the outer frame: complete steel structure shot-blasted, then all designated visible areas hot metalized with ZINACOR 850 (Zinc 85% - Aluminum 15%)

Stanje: novo, lastna masa: 13.500 kg, največja dovoljena obremenitev: 51.500 kg, skupna masa: 69.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimizing loading platform length, length approx. 3,700 mm Gooseneck rear with chamfering approx. 1,000 mm x 10° Loading Platform: Telescopic loading platform, length approx. 8,800 mm, with rear chamfering approx. 500 mm x 10° Recess in the chamfer as well as into the loading platform to accommodate the excavator dipper stick Pneumatic locking with conical pin and reinforced locking positions Supply lines routed protected within the extendable beam, adapting to the respective platform length Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps individually adjustable hydraulically approx. 235 mm to the outside and approx. 215 mm to the inside Axles and Suspension: BPW axles and suspension, two rigid axles, two steering trailing axles Electromagnetic reverse lock, activated via reverse gear and manually Air suspension with lift and lower valve Axle tool Tyres: 235/75 R17.5 3PMSF twin tyres Load index: 143/141J (144/144F) Brake System: WABCO braking system, EBS-E in accordance with EU regulations Lighting System: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Metalizing: Standard HRM metallization of the outer frame Complete steel structure shot-blasted, then visible defined surfaces metallized with ZINACOR 850 (Zinc 85% - Alu 15%) hot-refined Steel Construction: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified as per DIN-EN 287-1 MAG welding process according to EN ISO 4063 Shielding gas M21 as per EN ISO 14175 Accessories Included: Front wall made of steel, plug-in, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin 24N connection per ISO-11852, 24S connection per ISO-3731, 15-pin connection per ISO-12098 Round NATO socket on the front connection strip Cable to supply electro-hydraulic unit and/or electric winch (35 mm², 3.5 m long) between trailer and tractor with connector (NATO-NATO) 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches 1 spare wheel with mounting adapter Outer beam of the gooseneck with fastening holes for screwable lashing rings. The first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included One fastening hole in the rear upper area of the gooseneck's outer beam for a screwable lashing ring 1 pair of screw-in lashing rings Approx. 40 mm thick hardwood covering above the gooseneck On the gooseneck, 1 pair of plug-in side aluminium walls, approx. 400 mm high, anodized On the gooseneck, a plug-in aluminium rear wall, approx. 400 mm high, anodized Bedok Ahugjpfx An Tjll 2" kingpin Gooseneck guide plate for fifth wheel, approx. 500 mm wide 4 wheel chocks with holder Holder for aluminium approach ramps Mechanical landing gear with 2-speed gearbox and crank Continuous hardwood floor approx. 50 mm thick on the loading platform, interrupted between axles Platform locking with conically welded locking profiles every 250 mm incl. tension plate Slotted holes at the front of the loading platform for attachable and adjustable bridging elements 1 intermediate table with recessed platform, approx. 300 mm wide for the draw-out tube with large cross-section, with sheet metal covering Front and rear with slotted holes

Stanje: novo, največja dovoljena obremenitev: 38.100 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.100 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5 3PMSF, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer of approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading platform: 5 pairs of fold-out lashing rings 3 pairs of fold-out lashing rings 1 pair of horizontal lashing rings at the front of the loading area Cut-outs in the outer frame of the loading surface for hooking in tension belts Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Bedotphtmopfx An Toll Landing legs: JOST landing legs with 2-speed gears for a 24 t lifting capacity Axles and tyres: BPW axles, two axles are fixed, two axles are self-steering, air-suspended, with drum brakes, with lift/lower function The self-steering axles come with an electro-magnetic reverse lock, which is activated via reverse gear or manually Axle toolkit Tyres: 205/65 R17.5 3PMSF Brake system: WABCO brake system according to EU regulations with EBS-E Steel construction: Steel structure made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Electrical equipment: Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK lighting ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component zinc dust primer High-quality single-colour 2-component top coat in MB 7350 Novagrau No metallic paint possible Rear section metallized and painted in RAL 9010 Accessories included: 1 spare wheel 205/65 R 17.5 TPMS tyre pressure monitoring system acc. to ECE R 141 At the galvanized front connection strip yellow-red air couplings 4 wheel chocks with holder on front wall Bracket at rear of gooseneck for ALU access ramps Galvanized folding supports under the chamfer of the loading surface Mount for a revolving beacon at the rear of the trailer Height-adjustable curtain structure Galvanized front wall with a tension mechanism for the sliding curtains Height-adjustable by approx. 400 mm "EDSCHA" brand roof, sliding forward on ALU roof beam profiles, bolted to the front and rear wall In the loading surface, 3 pairs of sliding stakes Superstructure at rear hydraulically extendable to left and right by approx. 750 mm Sliding roof with upward swinging portal carrier Sliding tarp with 700 mm reserve length, with tension straps at intervals of approx. 600 mm Height to top edge of superstructure approx. 3,960 mm Journeys with the sliding roof open are not permitted and will damage the tarp Mounting rail for ALU access ramps at the rear of the vehicle At the gooseneck and at the rear panel left and right, each with a mount for warning signs incl. socket A mud flap at the rear of the trailer European reflector plates at the rear of the trailer 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading area Lifting axle on the front axle controlled by TEBS E depending on current axle load and load status Rear structure with closed ALU double-wing doors A sanded, anti-slip paint layer on the checker plates on the gooseneck and on the loading surface BEKAMAX centralized lubrication system with standard grease NLGI-2 and a removable guard around the pump Speed stickers 80 km/h on rear and both sides Load manometer for axle load determination including load chart

Stanje: novo, največja dovoljena obremenitev: 49.000 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with front corners chamfered at 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Extendable Loading Platform: - Loading platform, extendable design with rear chamfer of approx. 1,000 mm x 8° - 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) Blsdeh Etf Rjpfx An Tsl - 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - 1 pair of horizontal lashing rings at the front of the loading platform (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for securing straps (LC 2,000 daN) - Hardwood flooring approx. 48 mm thick, checker-plate covering above the axles Two-Part Removable Ramps: - One pair of galvanized two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp sections, hydraulic lifting mechanism, and hydraulic side-shift - Maximum load per pair: 40,000 kg Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Axles and Tyres: - BPW axles, two fixed axles and two steering axles (self-steering), air suspended, with drum brakes, raise/lower function - Self-steering axles with electro-magnetic reverse lock, can be activated by reverse gear or manually - Axle tool kit - Tyre size 235/75 R 17.5 Brake System: - Braking system according to EU regulations with EBS-E (4S3M) Steel Structure: - Steel structure made of high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Paintwork: - First-class, long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component (2K) zinc dust primer - High-quality single-tone topcoat using 2-component (2K) paint in Nova grey Electrical System: - Electrical system according to EU regulations, 24 volt lighting, ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX on the front connector strip with 24N, 24S, and 15-pin sockets Included Accessories: - 2" kingpin - Galvanized steel front wall, approx. 400 mm high - One spare wheel with holder in front of the headboard - Yellow-red air couplings on the galvanized front connector strip - 4 wheel chocks with holders on the front wall - Mount at the rear section of the gooseneck for ALU approach ramps - Galvanized folding supports underneath the loading platform chamfer - One holder for warning beacon - Cover plates to bridge the gap between ramps and loading platform - White reflective tape on the side, red on extension and rear, according to EU regulations - Electro-hydraulic power unit - At the gooseneck and ramps (left/right) a holder each for warning signs including socket - Control valves for the ramps mounted on the right side of the trailer - One mud flap at the rear of the trailer - Manual and documentation on USB stick - On the gooseneck, plug-in ALU side boards and rear wall approx. 2,440 x 400 mm - Rear galvanized plug-in stakes are removable (body length approx. 2,560 mm) - 4 pairs of WADER container pockets in the loading platform for one 20ft, two 20ft or one 40ft container - 7 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading platform - Galvanized, extendable platform wideners approx. 230 mm per side - Lift axle on the front axle with control system - 20 x 20 mm square climbing bars - BEKAMAX central lubrication system - Four warning signs extendable by approx. 400 mm eac

Stanje: novo, lastna masa: 15.450 kg, največja dovoljena obremenitev: 65.550 kg, skupna masa: 80.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 21.900 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 925 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimized platform length, approx. 3,700 mm long, with rear tapering of approx. 1,000 mm x 10° Technical fifth wheel load: 30,000 kg. For tractors: 4x2, 6x2, and 6x4 Bsdpfx Ajrigw Rsn Toll Loading Platform: Double-extendable loading platform, approx. 8,800 mm long with rear taper of approx. 500 mm x 10°. A support table approx. 300 mm wide is welded to the central beam, featuring elongated slots at the front and rear for optional bridge elements that can be hooked in and repositioned Pneumatic locking with conical locking pin and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles and Tyres: BPW axles and suspension, first axle self-steering, all other axles hydraulically and mechanically forced-steered First axle equipped with an electro-magnetic reverse lockout, activated via reverse gear and manually. Technical axle load: 12,000 kg. Air suspension with lift and lower valve Manufacturer by our choice Sockets and Lighting: 24-volt lighting system in accordance with EU regulations ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Complete HRM metallizing Full steel construction, shot-blasted, then hot-finished with ZINACOR 850 Paintwork: 6-stage finishing process: Complete steel construction shot-blasted after welding 1 coat of zinc-based primer, 1 coat of adhesion primer. Final paintwork in 2 coats of 2K paint in single-tone DB 7350 Novagrau, followed by cavity sealing with special wax Accessories: Detachable front wall made of steel, approx. 400 mm high Connection strip for supply lines to the tractor unit, fitted at the height of the outer frame profile ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets. If your pin configuration deviates from the ISO connector standard, please inform us 3 kW electro-hydraulic power unit for hydraulic functions (excluding hydraulic winches) 1 pair of plug-in ALU sidewalls on the gooseneck, approx. 400 mm high, anodized finish 3.5'' king pin. Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide 2 wheel chocks with holder in front of the front wall Mechanical landing legs with 2-speed gearbox and crank Control valves for hydraulic ramps located on the right side of the vehicle 1 pair of mechanical rear supports Central lubrication system with 1 pump, BEKAMAX brand, using standard grease according to NLGI-2 Removable guard covering the pump(s) of the central lubrication system Remote steering from front and rear, controlled by cable remote with push buttons, with axle tracking control, no installation required on tractor unit Under the gooseneck and on the rear crossmember, one 7-pin socket with holder for warning signs each on left and right. One 7-pin socket on the rear crossmember Manual and documentation One-piece INOX stowage box, approx. 2,480 x 340 x 390 mm, straight design Please note that any special equipment and accessories will increase the unladen weight and correspondingly reduce the payload Warning package: 4 warning boards, approx. 423 x 423 mm, extendable by approx. 1,000 mm, incl. 2 LED position lights and brackets for beacon.

Stanje: novo, lastna masa: 13.250 kg, največja dovoljena obremenitev: 47.550 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, vzmetenje: zrak, velikost pnevmatike: 245/70 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings 30 mm thick hardwood flooring Extendable loading platform: Loading platform in extendable design with rear chamfer approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings 3 pairs of outward-folding lashing rings 1 pair of flat lashing rings at the front of the loading area Cut-outs in the outer frame of the loading area for inserting tension straps Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Two-part steel ramps: One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering. Ramp with hydraulically folding and unfolding parts, hydraulic lifting system, and hydraulically adjustable position. Maximum load per pair: 40,000 kg Landing legs: Bledpfx Anel Uxdko Tjl JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced-steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool Tires 245/70 R 17.5 Braking system: Braking system according to EU regulations with EBS-E (4S3M) without connecting lines to tractor unit Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer High-quality one-color two-component (2K) top coat in Novagrau Rear section metallized and painted in RAL 9010 (pure white) Metallic paint not possible Electrical system: Electrical system according to EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connections conforming to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" kingpin One galvanized steel headboard approx. 400 mm high At the galvanized front connection strip, yellow-red air couplings 4 wheel chocks with holders at the headboard One spare wheel with holder in front of the headboard Electro-hydraulic power unit Rear and front remote steering via cable remote control with push-buttons, with single-track control of the axles Bracket at rear of gooseneck for ALU drive-on ramps European reflector signs (red-yellow) at trailer rear White reflective tape according to EU regulations at the sides, at the extension, and red at the rear At the gooseneck and on the ramps left and right, each with a holder for warning signs including socket One holder for beacon at trailer rear Galvanized folding supports under the loading platform chamfer Ramp operating valves fitted on the right side of the trailer Cover plates to bridge the gap between ramps and loading platform One mudflap at trailer rear Manual and description on USB stick Central lubrication system BEKAMAX (Pico) with general-purpose grease NLGI-2 and removable pump guard On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm The rear galvanized stakes are removable, superstructure length approx. 2,560 mm One INOX toolbox 1,350 x 400 x 400 on the gooseneck, box covers oil filler cap 4 pairs of WADER container pockets in the loading area for a

Stanje: novo, lastna masa: 22.700 kg, največja dovoljena obremenitev: 79.300 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 11.000 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 920 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 22.700 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize load platform length, approx. 3,750 mm long, rear with chamfer approx. 850 mm x 10° - Hydraulically liftable and lowerable, stroke ± 250 mm including hydraulic connection linked to the hydraulic axle compensation of the first two axles - Open in the rear third - For tractor units: 6 x 4 and 8 x 4 Load platform: - Extendable load platform, approx. 11,000 mm long with rear chamfer approx. 500 mm x 10° - Recess in the platform and into the chamfer for receiving the excavator dipper stick, approx. 4,240 x 900 x 440 mm - Pneumatic locking with conical locking pin and reinforced locking positions, supply lines protected within the extendable beams, automatically adapting to the actual platform length Ramps: - One pair of two-piece steel ramps approx. 4,650 mm long and 900 mm wide - Hydraulically foldable ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 215 mm inward - 25 mm "Super Grip" rubber flooring and approx. 5 mm checker plate as additional reinforcement on the chamfered section of the platform - Square climbing strips 20x30 mm, spaced approx. every 200 mm on the outer frame of the ramp Bjdek Af Svepfx An Tjll Axles, Suspension, and Tires: - PA-X axle system, all axles hydro-mechanically forced steered - Steering performance of the first two axles can be optimally adjusted to the platform length, both mechanically and hydraulically - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-fitted locking pins for securing in raised position - 245/70 R 17.5 3PMSF Accessories included: - Plug-in steel front wall, approx. 400 mm high - Supply line connection strip for tractor unit, mounted at the height of the outer frame profile - 1 spare wheel - Outer beams of gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from front, then every approx. 400 mm - 2 pairs of screw-in lashing rings included - Chequer plate covering over the gooseneck - On gooseneck: 1 pair of removable anodized ALU side walls, approx. 400 mm high - On gooseneck: 1 removable anodized ALU rear wall, approx. 400 mm high - 3.5" king pin / 2" king pin mounted - Guide plate of the gooseneck for fifth wheel plate, approx. 500 mm wide - 4 chocks - 4 axle load gauges - Mechanical drop tube supports at the front - 1 one-piece INOX toolbox, approx. 2,480 x 340 x 390 mm - Mechanical drop tube supports at the front - Continuous steel deck with baked-in sand layer as anti-slip protection on the platform - 1 intermediate table, approx. 500 mm wide, for the extension, with slotted holes for insertable and relocatable bridging elements - Sand coating on support surfaces of the intermediate table - Mechanical locking for securing the intermediate table on the extension - 8 pairs of stake pockets in the outer frame - Extendable (galvanized) widenings, approx. 230 mm per side - 1 pair of hydraulic rear supports - Central lubrication system - 1 reversing spotlight each on left and right rear of the vehicle - 3 kW electro-hydraulic power unit - Loose widening planks in reinforced steel U-frame - Radio and cable remote control - 4 warning signs, approx. 423 x 423 mm

Stanje: novo, lastna masa: 10.600 kg, največja dovoljena obremenitev: 39.400 kg, skupna masa: 50.960 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5, barva: siv, obratovalna teža: 10.600 kg, Oprema: ABS, Gooseneck: - Gooseneck with 30 mm hardwood flooring - Gooseneck at rear in straight version - 3 pairs of lashing rings (LC 5,000 daN) Extendable load floor: - Load floor in extendable configuration - 5 pairs of lashing rings foldable outward - 3 pairs of lashing rings foldable outward - 1 pair of lashing rings laying at the front end of the load floor - Cut-outs in the outer frame of the load floor for attaching tension straps - Approx. 48 mm hardwood flooring, checker plate covering above the axles Landing legs: - JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tyres: - BPW axles, two rigid axles, two self-steering axles - Air suspension with drum brakes, with lift/lower function - The self-steering axles are equipped with an electromagnetically operated reverse lock, which can be activated via reverse gear or manually - Axle tools - Tyres 205/65 R17.5 Brake system: - Brake system compliant with EU regulations with EBS-E (4S3M) Steel structure: - Steel construction made from high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system in accordance with EU regulations, lighting 24 Volt, ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets - Connections according to ISO: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Paintwork: - High-quality and durable corrosion protection on the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer - High-quality single-colour 2-component (2K) top coat in Novagrau - Rear section metallised and painted in RAL 9010 (Pure White) Included accessories: - One spare wheel with holder in front of the bulkhead - 2" king pin - Galvanised steel front wall approx. 400 mm high - Yellow-red air couplings on the galvanised connection bar at the front - 4 wheel chocks with holder at the front wall - Galvanised folding supports under the load floor slope - Holder for a warning beacon at the rear of the trailer - Galvanised extensions, extendable by approx. 230 mm per side - White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear - On the gooseneck and rear panel, left and right, one bracket each for warning panels including socket - European reflective markings (red-yellow) at the rear of the trailer - TPMS tyre pressure monitoring system according to ECE R 141 - On the gooseneck, plug-in ALU side walls and rear wall, approx. 2,440 x 400 mm - The rear, galvanised plug-in side stanchions are removable, length of the body approx. 2,560 mm - 7 pairs of WADER container pockets - 1x 20ft container on the load floor; 1x 40ft container on the load floor; 1x 40ft container above the gooseneck; 2x 20ft container - 7 pairs of stanchion sockets for plug-in stanchions 100 x 50 mm in the outer frame of the load floor - Lift axle on the front axle with control via TEBS E, depending on the current axle load and load condition - Sliding plug-in rail for ALU loading ramps at the rear of the vehicle - Anti-slip sand finish painted on the checker plates on the gooseneck and load floor - Four warning boards extendable by approx. 400 mm, approx. 423 x 423 mm, each with a position lamp Blodpfxst Ag Uwj An Tjl - Holder for warning beacon on the warning boards - 80 km/h speed stickers at the rear and on both sides - Axle load gauge for determination of axle loads inclu

Stanje: novo, lastna masa: 15.900 kg, največja dovoljena obremenitev: 63.500 kg, skupna masa: 68.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 12.700 mm, širina tovornega prostora: 2.740 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75/r17,5, barva: siv, obratovalna teža: 52.100 kg, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimal load bed length, approx. 3,300 mm long, rear with taper approx. 1,000 mm x 10° Technical fifth wheel load: 23,000 kg For tractor units: 6x2, 6x4, and 8x4 Load bed: Extendable load bed, approx. 9,400 mm long with rear taper approx. 500 mm x 10° A recess in the load bed as well as in the tapering section for accommodating the excavator dipper stick, approx. 3,850 x 950 x 210/290 mm Pneumatic locking with conical locking bolt and reinforced locking positions, service lines are protected within the extendable beams and automatically adapt to the respective bed length Axles and Tires: BPW axles and suspension, 1st axle fixed, all other axles hydro-mechanically forced steered Bjdpfxsmfqi Ij An Tsll Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool 235/75 R 17.5 3PMSF twin tires Load index 143/141J (144/144F) Two-piece steel ramps: One pair of two-piece steel ramps, approx. 4,350 mm long and approx. 900 mm wide Hardwood covering Hydraulically folding ramp tips, each ramp hydraulically adjustable approx. 235 mm outward and approx. 215 mm inward Braking system: Braking system by WABCO EBS-E according to EU regulations Sockets and lighting: 24-volt lighting system Full metallization: Complete HRM metallization with ZINACOR 850 for optimal corrosion protection Surface treatment: Entire steel structure automatically blast cleaned with shot blasting after welding Second blasting treatment with corundum for optimal coating adhesion Final painting: 2 coats of 2-component paint in Novagrau, followed by sealing of cavities with special wax Rims in silver-grey Steel construction: Steel construction from high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Accessories: Plug-in steel front wall, approx. 400 mm high Connection rail for service lines to the tractor unit Spiral cable for supplying the electro-hydraulic unit and/or electric winch between trailer and tractor unit, with plug for the electro-hydraulic unit to control hydraulic operations, except for hydraulic winches Outer beam of gooseneck with mounting holes for bolted lashing rings First hole approx. 200 mm from the front, thereafter approx. every 400 mm One mounting hole in the rear upper area of the outer gooseneck beam for a bolted lashing ring Approx. 40 mm thick hardwood floor on the gooseneck, checker plate floor over the kingpin Guide plate on gooseneck for the fifth wheel plate, approx. 500 mm wide On the load bed, continuous and between the axles intermittent approx. 50 mm thick hardwood floor Load bed locking with conically welded locking profiles every 250 mm, including preload plate Slotted holes for attachable and movable bridging elements: on the fixed section behind the gooseneck at the front of the load bed 1 movable intermediate table for the extension tube with large cross-section Control valves for the hydraulic ramps on the right side of the vehicle Central lubrication system with 1 pump, standard grease according to NLGI-2 Radio remote control for steering operation, in addition to cable remote control, with 2 control lights on the receiver for single-track steering monitoring

Stanje: novo, lastna masa: 14.800 kg, največja dovoljena obremenitev: 61.700 kg, skupna masa: 76.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck with rear chamfer of approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Loading Platform: • Extendable loading platform with rear chamfer of approx. 500 mm x 8° • 9 pairs of folding external lashing rings • 1 pair of recessed lashing rings at the front of the loading platform • Cutouts in the outer frame of the loading platform for attaching tension belts • Approx. 48 mm thick hardwood flooring, checker plate above the axles Landing Legs: • JOST mechanically operated landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: Blsdpfx Aema Hf Ren Tol • BPW axles and suspension, 1st axle steering, 2nd and 3rd axle fixed, 4th and 5th axle follow-steering • Technical axle load: 12,000 kg • 1st, 4th, and 5th axles with electromagnetic reverse lock, activated via reverse gear or manually • Tyres: 235/75 R 17.5 3PMSF Brake System: • WABCO brake system in accordance with EU regulations including EBS-E (4S3M) Paintwork: • Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer • High-quality single-color two-component (2K) topcoat in MB 7350 Novagrau • Rear section metallized and painted in RAL 9010 (Pure White) Steel Construction: • Steel structure made from high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC (yield strength 355MPa) • S690QL/S700MC (yield strength 690MPa) Accessories: • One spare wheel with holder in front of the front wall • 2" king pin • Galvanized steel front wall, approx. 400 mm high • Front galvanized connection strip with yellow-red air couplings • 2 wheel chocks with holders mounted on the front wall • Rear mount on gooseneck for ALU drive-on ramps • Galvanized extendable wideners appx. 230 mm per side • Bracket for a beacon at the rear of the trailer • Galvanized supports under the chamfer of the loading platform • White reflector tape on the sides as per EU regulations, red at the extension and rear • Mounts for warning panels including socket left and right at the gooseneck and rear panel • Detachable ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • Rear galvanized plug-in stanchions removable (body length approx. 2,560 mm) • 3 pairs of WADER container pockets in the loading platform for a 20ft (30ft) or a 40ft container • 7 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform • Lifting axle on the front axle with TEBS E control according to the current axle load and loading condition • Movable mounting rails for ALU drive-on ramps at the rear of the vehicle • 20 x 20 mm square climbing strips at 200 mm intervals on the outer frame chamfer of the loading platform • BEKAMAX (Pico) centralized lubrication system with NLGI-2 standard grease and removable pump cover • Four extendable warning panels approx. 423 x 423 mm with a position light, extendable by approx. 400 mm • Holder for beacon mounted on the warning panels • European reflector plates (red-yellow) on the rear of the trailer • 80 km/h speed limit stickers at rear and both sides • Axle load gauge with load diagram included • HRM Metallisation (High Resistance Metallisation) of the outer frame • Complete steel structure is shot-blasted, then defined visible surfaces are metallized with ZINACOR 850 (zinc 85% - aluminum 15%) using hot finishing

Stanje: rabljeno, lastna masa: 10.600 kg, največja dovoljena obremenitev: 39.400 kg, skupna masa: 50.960 kg, konfiguracija osi: 3 osi, prva registracija: 09/2024, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5, barva: siv, Leto izdelave: 2024, obratovalna teža: 10.600 kg, Oprema: ABS, Vrat: -Vrat z oblogo prevleko iz trdega lesa, debeline 30 mm -Vrat na zadnji strani v ravni izvedbi -3 pari zateznih obročev (LC 5.000 daN) Nakladalna površina z izvlečno izvedbo: -Nakladalna površina z izvlečno izvedbo -5 parov zateznih obročev, ki se zunanje odklapljajo (LC 5.000 daN) -3 pari zateznih obročev, ki se zunanje odklapljajo (LC 10.000 daN) -1 par zateznih obročev, nameščen vodoravno spredaj na nakladalni površini (LC 10.000 daN) -Izrezi na zunanjem okvirju nakladalne površine za pritrditev zategovalnih pasov (LC 2.000 daN) -Obloga iz trdega lesa, debeline približno 48 mm; nad osmi je prevleka iz valjane pločevine Podpora sedla: -JOST podpore sedla (mehanske) z 2-stopenjskim menjalnikom za 24 t nosilnosti (5 t testna nosilnost) Osi in pnevmatike: -BPW osi, dve fiksni osi, dve sledilni osi -Zračna vzmet, z bobnasto zavoro, z funkcijo dviganja/spuščanja -Sledilne osi z elektromagnetično blokado za vožnjo v vzvratno smer, ki se aktivira preko vzvratnega prestave ali ročno -Pnevmatike 205/65 R17.5 Zavorna naprava: -Zavorna naprava v skladu z uredbami EU, z EBS-E (4S3M) Jeklena konstrukcija: -Jeklena konstrukcija iz visoko trdnih finozrnatih jekel -Vrste jekel: -S355J2+N/S355MC (meja tečenja 355 MPa) -S690QL/S700MC (meja tečenja 690 MPa) Bjdpfx Anew Adkxj Tsll Električna napeljava: -Električna napeljava v skladu z uredbami EU, razsvetljava 24 voltov, ASPÖCK-NORDIK (ASS3) -ASPÖCK-UNIBOX na priključni letvi spredaj s vtičnicami 24N, 24S in 15-polno -Barvanje: -Prvo razredna in dolgotrajna protikorozijska zaščita standardno peskane varjene konstrukcije je zagotovljena z dvokomponentnim (2K) cinkovo-prašnim temeljnim premazom -Visokokakovosten dvokomponentni (2K) končni premaz, enobarvni, v barvi Novagrau Vključena dodatna oprema: -En rezervni zračniški kolo z nosilcem pred čelno steno -2" kraljeviče -En pocinkana jeklena čelna stena, približno 400 mm visoka -Na pocinkani priključni letvi spredaj rumeno-rdeče zračne spojke -4 kosi klinih z nosilcem na čelni steni -Pocinkane zložljive podpore pod poševnino nakladalne površine -Nosilec za rotacijsko luč na zadnji strani prikolice -Podaljški, pocinkani, izvlečni za približno 230 mm na vsaki strani -Bel refleksni trak v skladu z uredbami EU, na strani, na izvlečni površini in zadaj rdeč -Na vratu in na zadnji plošči na levi in desni strani po en nosilec za opozorilne table, vključno z vtičnico -En odbijač blata na zadnji strani prikolice -Evropski odsevni znaki (rdeče-rumeni) na zadnji strani prikolice -Priročnik in navodila na USB pomnilniku -Sistem za nadzor tlaka v pnevmatikah (TPMS) v skladu z ECE R 141 -Na vratu aluminijaste stranske stene in zadnja stena, ki se vstavi, približno 2.440 x 400 mm -Zadnje, pocinkane vstavne ograje so odstranljive, dolžina nadgradnje je približno 2.560 mm -7 parov držal za kontejnerje WADER -1 x 20-čevlni kontejner na nakladalni površini; 1 x 40-čevlni kontejner na nakladalni površini; 1 x 40-čevlni kontejner nad vratom; 2 x 20-čevlni kontejner -7 parov držal za ograje za vstavne ograje 100 x 50 mm na zunanjem okvirju nakladalne površine -Dvižna os na sprednji osi z nadzorom preko TEBS E, odvisno od trenutne obremenitve osi in trenutnega stanja obremenitve -Premikajoča se letva za pritrditev aluminijastih plošč na zadnji strani vozila -Na valjani pločevini na vratu in na nakladalni površini prevleka iz peska kot zaščita pred zdrsom -Štiri opozorilne table, ki se približno za 400 mm izvlečejo, približno 423 x 423 mm, z pozicijsko lučjo -Na opozorilnih tablah nosilec za

Stanje: novo, največja dovoljena obremenitev: 73.540 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, Our complete vehicle inventory, including immediately and short-term available vehicles, can be found on our website. Excerpt from the equipment specification. Full equipment details available upon request. Gooseneck: * Hydraulically liftable/lowerable and detachable gooseneck, length approx. 3,650 mm * 2 pairs of fold-out lashing rings on the exterior (LC 5,000 daN) * 2 pairs of lashing rings on the gooseneck (LC 10,600 daN) * 1 pair of lashing rings in the center of the gooseneck (LC 10,600 daN) * Suitable for tractor units 6 x 4 or 8 x 4, 2-axle Compact front bogie: * Hook coupling front and rear, length approx. 2,200 mm * Bogie width: approx. 2,850 mm Excavator deck: * Telescopic excavator deck with drive-over deck hooks at the front and pin-eye coupling at the rear * Base width: approx. 2,850 mm * Length: approx. 6,650 mm * Beam height: approx. 400 mm * Beam width: approx. 1,350 mm * Loading height approx. 550 mm with ground clearance approx. 150 mm 4-axle rear bogie: * Mechanical pin-eye coupling at the front for connecting a low-bed trailer * Rear end cross member, bogie width: approx. 2,850 mm * Bogie length: approx. 5,480 mm Oscillating axles, all axles hydro-mechanically forced-steered * Technical axle load: 14,640 kg per axle (62 km/h) * Hydraulic axle compensation Tyres: * Front bogie: 8 x (manufacturer’s choice; M+S) 285/70 R19.5 * Rear bogie: 16 x (manufacturer’s choice; M+S) 285/70 R19.5 * Load index 150/148J Paintwork: * Complete steel structure automatically shot-blasted after welding using a turbine blasting unit. Second abrasive blasting with corundum for optimum coating adhesion * Full chassis HRM-metalized with ZINACOR 850 (85% zinc/15% aluminum) for maximum corrosion protection * Final coating in 2 layers of 2-component top coat, single color in RAL 3002 carmine red, according to RAL 841GL system Including the following accessories: * Steel front wall, approx. 400 mm high * Plug-in ALU side panels and rear wall on the gooseneck, approx. 400 mm high, anodized finish * 3.5-inch kingpin * Truck hydraulic connection with flow controller (20 l/min) * Overhead support for supply lines; tractor unit tank must hold at least 80 l * With MAX Trailer coupling pieces; otherwise, couplings to be supplied by the customer ex works * BEKA-MAX centralized lubrication for gooseneck with standard grease NLGI-2 * Tool kit Art No. 612452 * Multi-coupling hydraulic connections on the gooseneck * Front bogie with separate air connection for air-powered tools Bsdpfjxbmplex An Tsll * BEKA-MAX centralized lubrication for 2-axle bogie with standard grease NLGI-2 * One 7-pin socket each left and right at the rear of the front bogie for warning panels * Threading option (ø approx. 40 mm) every approx. 500 mm on the outside of the top flange of the excavator deck outer tube for screw rings (LC 16,000 daN) * Foldable extensions with steel mats, width adjustable from approx. 2,850 mm to approx. 3,250 mm * BEKA-MAX centralized lubrication for 4-axle bogie with standard grease NLGI-2 * Socket on the rear bogie for cable remote control of rear steering * Rear bogie with trough * Two stainless steel toolboxes, approx. 855 x 340 x 390 mm, mounted on the gooseneck left and right * Single-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery * Radio remote control: * Operation of the power pack, start/stop of the diesel engine * Operation of the rear steering, in addition to cable remote control * One LED work spotlight each left and

Stanje: rabljeno, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, prva registracija: 09/2017, * SAF osi * Kolesni izrezi * Hidravlične nakladalne rampe, nastavljive po širini Blodpowta Alsfx An Tsl * Zračno vzmetenje * Možnost razširitve * Lastna teža: 11.020 kg ----Interna številka vozila: 11010----Napake in vmesna prodaja pridržane. WhatsApp podpora na voljo! Za vprašanja o vozilu ali dodatne informacije nam pišite udobno preko WhatsAppa WhatsApp nemško, angleško -- WhatsApp nemško, angleško, arabsko

Stanje: novo, lastna masa: 10.300 kg, največja dovoljena obremenitev: 39.200 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Platform: - Loading platform after the gooseneck, hydraulically liftable and lowerable, length approx. 2,800 mm, with rear chamfer approx. 1,000 mm x 8° - Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, over the axles with chequer plate covering Two-part Steel Ramps: - One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp parts, hydraulic lifting system, and hydraulically adjustable - Maximum load per pair: 40,000 kg Axles, Suspension and Tires: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated by reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tires 235/75 R 17.5 3PMSF - TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories Included: - One spare wheel with holder in front of the bulkhead - 2" kingpin - One galvanized steel front wall approx. 400 mm high - Yellow-red air couplings at the galvanized connection strip in front - 4 wheel chocks - Galvanized folding supports under the platform's rear chamfer - A holder for a rotating beacon at the rear of the trailer - Cover plates to bridge the gap between ramps and platform - White reflective tape as per EU regulations along the sides of the trailer and red at the rear - Electro-hydraulic unit at the rear, under the platform - At the gooseneck and at the ramps left and right, each with a holder for warning signs, including socket - Control valves for the ramps positioned on the right side of the trailer - European reflective plates (red-yellow) at the rear of the trailer Bsdpfxou Hp Hrs An Toll - Manual and description on USB stick - Removable ALU side walls and rear wall on the gooseneck approx. 2,440 x 400 mm - The rear, galvanized side stakes are removable (body length approx. 2,560 mm) - An electric cable winch with radio remote control, approx. 5,400 kg lifting force, including 9.5 mm steel cable, 24 m long, with guide roller - Bolted 5 t ring for cable deflection of the winch on the gooseneck without pulley - 2 pairs WADER container pockets in the platform for a 20ft container - 6 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the platform - Lift axle on the front axle with control via TEBS E, depending on actual axle load and loading condition - 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN) - 1 pair of recessed lashing rings along the central beam at the rear chamfer (LC 10,000 daN) - Sand coating for slip resistance painted on the chequer plates on the gooseneck and on the platform - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and removable pump protection - Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm - Speed stickers 80 km/h rear and on both sides - Load manometer for determining axle loads including load chart - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then all defined visible surfaces metallized and hot-coated with ZINACOR 850 (zinc 85% - alu 15%)

Stanje: novo, lastna masa: 14.350 kg, največja dovoljena obremenitev: 53.450 kg, skupna masa: 67.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, dvižna zadnja plošča, Gooseneck: - Gooseneck in SNT design for optimization of loading bed length, length approx. 3,700 mm - Gooseneck rear with chamfer approx. 1,000 mm x 10° - For tractor units: 6x2, 6x4, 8x4 short Loading bed: - Extendable loading bed, length approx. 8,800 mm, rear chamfer approx. 500 mm x 10° - A recess in the loading bed and the chamfered section for receiving the excavator dipper stick, approx. 3,850 x 750 x 210/290 mm Two-part steel ramps: - One pair of two-part steel ramps, length approx. 4,350 mm, width approx. 900 mm - Ramps with rubber covering - Ramps hydraulically adjustable individually approx. 235 mm outwards and approx. 215 mm inwards - 'Super Grip' 25 mm rubber flooring and approx. 5 mm steel plate as additional reinforcement on the rear chamfer of the loading bed - Square climbing bars 20 x 30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: - BPW axles and suspension, 1st axle steering, all other axles hydromechanically forced-steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Tires 235/75 R 17.5 - TPMS tire monitoring system according to ECE R141 - TPMS tire sensors fitted on all wheels, including spares Surface treatment: - Complete steel structure automatically blasted with shot blasting system after welding - Second blasting with corundum for optimum coating adhesion - HRM metallization of entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for best corrosion protection - Final painting with 2 layers of 2K top coat, single colour in MB 7350 Novagrau Accessories included: - Plug-in steel front wall, approx. 400 mm high - 3kW electro-hydraulic power unit for controlling hydraulic functions, with the exception of hydraulic winches - 1 spare wheel - Outer carrier on the gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings in the rear area of the gooseneck - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized - On the gooseneck, 1 plug-in ALU rear board, approx. 400 mm high, anodized - On top of the gooseneck, approx. 40 mm thick hardwood flooring, above kingpin area with checker plate cover - 2" kingpin - Round NATO socket on front connection strip - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front cross member - 8 pairs of recessed, fold-out lashing rings in the outer frame of the loading bed - Extendable (galvanized) widenings by approx. 230 mm per side - Wheel recesses with square climbing bars, 15 x 15 mm, in front of the axles fully open up to gooseneck cross beam, approx. 700 x 410 mm - Wheel recesses with square climbing bars, 15 x 15 mm, between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - ALU covers for wheel recesses, which can also be used as bridging elements for the extension or as widening boards - 1 pair mechanical rear supports - Radio and cable remote control - Lift axle on front axle - Square climbing bars 20 x 30 mm, approx. every 200 mm Bledjya E A Njpfx An Tsl - Central lubrication system with 1 pump - Wabco Smart Board system - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, največja dovoljena obremenitev: 50.400 kg, skupna masa: 65.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment specification. Full specification available on request. GOOSENECK * Gooseneck in SNT design to optimize platform length, approx. length 3,700 mm, with rear bevel of approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high Bjdpfxstx Nwno An Tjll * ASPÖCK-UNIBOX at the front connection rail with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, except for hydraulic winches * 1 pair of detachable ALU side walls, approx. 400 mm high, anodized finish * 1 detachable ALU rear wall, approx. 400 mm high, anodized finish * Over the gooseneck, approx. 40 mm thick hardwood flooring, over the king pin with checker plate covering * 2-inch king pin * Mount at the rear of the gooseneck for ALU drive-on ramps * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) LOAD PLATFORM * Extendable load platform, approx. length 8,800 mm, with rear bevel approx. 500 mm x 10° * Recess in platform and rear bevel for accommodating an excavator dipper stick, approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st axle self-steering, all other axles hydro-mechanically forced steered * 1st axle with electromagnetic reversing lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with lift and lower valve * Tires: 235/75 R 17.5 3PMSF twin tires * Mechanical landing legs with 2-speed gearbox and crank, JOST Modul B - static test load = approx. 50,000 kg * Platform with continuous and between-axles interrupted 50 mm thick hardwood flooring (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable galvanized side extensions by approx. 230 mm each side (without wooden planks) * Wheel wells with square climbing strips, approx. 15 x 15 mm in front of the axles, continuous opening up to the cross member of the gooseneck, approx. 700 x 410 mm (W x D) * ALU covers for the wheel wells, usable as bridging elements for the extension OR as width extension planks * Lockable aluminium elements on the extension tubes of the side extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel wells with square climbing strips, approx. 15 x 15 mm between the 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * ALU covers for the wheel wells, usable as bridging elements for the extension OR as width extension planks * Lockable aluminium elements on the extension tubes of the side extensions * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with single-track monitoring of the axles, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-part steel ramps, type: DR-15/60-900-4350-KG-HV-M, approx. length 4,350 mm and width approx. 900 mm * Hydraulically folding ramp tips * Ramps hydraulically adjustable individually by approx. 235 mm outward and approx. 215 mm inward * Super Grip rubber surface approx. 25 mm and steel surface approx. 5 mm as additional

Stanje: novo, največja dovoljena obremenitev: 67.200 kg, skupna masa: 85.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete inventory of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment features. Full equipment details upon request. GOOSENECK * Gooseneck in SNT design for optimized loading platform length, approx. 3,700 mm long, with a rear chamfer approx. 1,000 mm x 10° * For tractor units: 6x2, 6x4, and short 8x4 * Plug-in steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for controlling hydraulic functions, excluding hydraulic winches Bedpfsrgzv Nox An Tjll * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in ALU sideboards, approx. 400 mm high, anodized finish * One plug-in ALU rearboard, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood flooring above the gooseneck, checker plate flooring above the king pin * 3.5 inch king pin * Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide * Round NATO socket on the front connection bar (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow control, incl. bracket for suspension of supply lines (Faymonville couplings) * 2 pairs of stake pockets sunk into the gooseneck, for plug-in stakes approx. 100 x 50 mm LOADING DECK * Extendable loading deck, length approx. 11,000 mm, rear chamfer approx. 500 mm x 10° * Pneumatic locking with conical locking bolt and reinforced lock positions, supply lines are routed protected in the extendable beams and automatically adjust to the respective platform length * BPW axles and suspension, 1st axle steerable, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Tyres: 235/75 R 17.5 3PMSF, twin tyres * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B - static test load = approx. 50,000 kg * Continuous 50 mm thick hardwood flooring on the loading deck, interrupted between the axles (increases coefficient of friction) * Slotted holes for attachable and re-positionable bridging elements: - on the fixed section behind the gooseneck - at the front of the loading area * 1 sliding intermediate table, approx. 500 mm wide, for the extension tube with large cross-section, with checker plate flooring, slotted holes front and rear for attachable and repositionable bridging elements * 1 pair of recessed horizontal lashing rings at the front of the fixed platform section (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the deck, fold-out to the outside (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering operated from both front and rear via cable remote control, with axle tracking control, no installation in the tractor unit * 1st axle with automatic lift-axle function and start-up aid according to EU Directive 2021/535 * Under the gooseneck and on the rear cross member, one 7-pin socket each on left and right, with bracket for warning signs * Painted sand coating on the outer frame of the platform as well as on the checker plates of the platform and in the transition area between the loading deck

Stanje: rabljeno, številka stroja/vozila: ***YAMT13XX6K0104043, konfiguracija osi: 3 osi, prva registracija: 01/2019, skupna dolžina: 13.800 mm, skupna širina: 2.550 mm, skupna višina: 3.410 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, barva: drugo, Leto izdelave: 2019, Chassis Chassis height: 87 cm Kingpin / Fifth wheel diameter: 2 inches Height of kingpin / drawbar: 120 cm Special transport 2-piece road plates: ✓ Hydraulic ramps: ✓ Loading deck length: 930 cm Ramp length: 395 cm Gooseneck length: 415 cm Low loader: ✓ Maximum width: 300 cm (25 cm per side) Max. length: 1380 cm Extendable: ✓ Tank Fuel: ✓ = Further Information = Blodpfx Aou H D R Esn Tol Axle configuration Tyre size: 235/75 R17.5 Axle brand: Saf Brakes: Drum brakes Suspension: Air suspension Axle 1: Twin tyres; Tyre tread left outer: 60%; Tyre tread right outer: 60% Axle 2: Twin tyres; Tyre tread left outer: 20%; Tyre tread right outer: 30% Axle 3: Twin tyres; Steering; Tyre tread left outer: 55%; Tyre tread right outer: 50% Weights Unladen weight: 10,040 kg Payload: 30,960 kg Gross vehicle weight: 41,000 kg Functional Body make: Faymonville Loading platform height: 87 cm Identification Registration number: C505325 = Company Information = For more information on this unit please call: or e-mail: . A full stock overview can be found at: . Please do not forget to subscribe to our newsletter for weekly updates on our stock.

Stanje: rabljeno, lastna masa: 7.000 kg, največja dovoljena obremenitev: 23.000 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, prva registracija: 01/2021, dolžina tovornega prostora: 8.100 mm, vzmetenje: zrak, velikost pnevmatike: 235/75R17,5 --/140J, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75R17,5 --/140J, velikost zadnje pnevmatike: 235/75R17,5 --/140J, voznikova kabina: drugo, emisijski razred: noben, Oprema: ABS, zavorni sistem na stisnjen zrak, Dolžina tovornega prostora pribl. 8.100 mm, nakladalna višina pribl. 890 mm, pritrdilna ušesa, -- tiskarske napake, napake in spremembe so pridržane, slikovni zgledi --, Več podatkov na: !, Več podrobnosti: ! Blodpfx Anjzymm Uo Tol

Stanje: rabljeno, lastna masa: 10.860 kg, največja dovoljena obremenitev: 37.140 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/2018, vzmetenje: zrak, velikost pnevmatike: 235/75 R17,5 140J, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R17,5 140J, velikost zadnje pnevmatike: 235/75 R17,5 140J, voznikova kabina: drugo, emisijski razred: noben, Oprema: ABS, zavorni sistem na stisnjen zrak, Gumijasta obloga, 2-delna rampa z rešetkastimi nosilci, rampe po celotni širini, elektro-hidravlična črpalka za rampe ali preko tovornjakove hidravlike, -- Pridržujemo si pravico do tiskarskih napak, napak in sprememb, vzorčne slike --, Več podatkov na: !, Več podrobnosti: ! Blodpfx Aozygc Nsn Tjl

Stanje: rabljeno, prevoženi kilometri: 130.100 km, moč: 368 kW (500,34 KM), prva registracija: 01/2018, vrsta goriva: dizel, lastna masa: 11.725 kg, največja dovoljena obremenitev: 14.275 kg, skupna masa: 26.000 kg, velikost pnevmatike: 315/80R22,5 156/L, konfiguracija osi: 3 osi, medosna razdalja: 4.800 mm, naslednji pregled (TÜV): 08/2026, gorivo: dizel, zavore: intarder, barva: drugo, voznikova kabina: spalna kabina, vrsta prenosa: samodejen, emisijski razred: Euro 6, vzmetenje: jeklo-zrak, velikost sprednje pnevmatike: 315/80R22,5 156/L, velikost zadnje pnevmatike: 315/80R22,5 /150K, Oprema: ABS, klimatska naprava, navigacijski sistem, spojka prikolice, tempomat, zapora diferenciala, zavorni sistem na stisnjen zrak, Meiler odklopni priklopnik, tip: RS 21.67, -- pridržane pravice do tiskarskih napak, napak in sprememb, ilustrativne slike --, več podatkov najdete tukaj: !, več podrobnosti: ! Bledpfx Aszygcvon Tsl

Stanje: novo, lastna masa: 7.200 kg, največja dovoljena obremenitev: 31.800 kg, skupna masa: 39.000 kg, konfiguracija osi: 3 osi, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, Length of upper deck approx. 4,180 mm, lower deck length approx. 9,400 mm, front wall approx. 800 mm high, 14 stake pockets in the outer frame, 8 removable stakes, 3 cross stake rails, 24 lashing eyes, 4 pairs of container locks. -- Subject to misprints, errors and modifications; sample images shown --, More data at: !, More details: ! Bedpfx Anozygane Tjll

Stanje: rabljeno, lastna masa: 10.720 kg, največja dovoljena obremenitev: 37.280 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 02/2019, naslednji pregled (TÜV): 02/2027, vzmetenje: zrak, velikost pnevmatike: 245/70 R17,5 ---/141J, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 245/70 R17,5 ---/141J, velikost zadnje pnevmatike: 245/70 R17,5 ---/141J, voznikova kabina: drugo, emisijski razred: noben, Oprema: ABS, zavorni sistem na stisnjen zrak, popolnoma prevozen, -- pridržujemo si pravico do tiskarskih napak, napak in sprememb, vzorčne slike --, Več podatkov na: !, Več podrobnosti: ! Blsdpfezygazjx An Tel