Faymonville Euromax Stz-3Aub nakup rabljenega (242)

Stanje: novo, največja dovoljena obremenitev: 36.040 kg, skupna masa: 53.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete inventory of immediately and short-term available vehicles can be found on our website. Iijdpfx Agjy Uwu Ie Eef Excerpt from the equipment list. Full specification available on request. Gooseneck: * Gooseneck in SNT design to optimize loading deck length, approx. 3,750 mm long * Gooseneck hydraulically liftable/lowerable and detachable * For tractor units: 6 x 4 or 8 x 4 Lowbed: * Lowbed with exterior beams, extendable, SUPER LOW design, approx. 8,000 mm long * Lowbed with fixed hardwood flooring approx. 40 mm thick and mechanical locking * Supply lines routed protected within the extendable beams, automatically adapting to the lowbed length * 7 pairs of folding lashing rings outward (LC 10,000 daN) * 6 pairs of threaded mounting blocks on the inner beam for screwable RUD rings Rear chassis: * Rear chassis with closed outer frame and tread plate cover * Chassis with excavator recess, closed in the rear half to house air tanks * 3 pairs of folding lashing rings outward (LC 5,000 daN) * 1 pair of folding lashing rings outward (LC 10,000 daN) * 1 pair of horizontal lashing rings, positioned front & rear on the chassis (LC 10,000 daN) Axles: * BPW axles and suspension, all axles with hydro-mechanical forced steering * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tyres: * Tyres 245/70 R 17.5 3PMSF – manufacturer at choice. Load index (146/146F) Braking system: * WABCO braking system according to EU regulations with EBS-E (2S2M) Coating: * HRM metalizing of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure optimal corrosion protection * Finished with 2 coats of 2K paint, single-colored in RAL 3002 Carmine Red, per RAL System 841GL Includes accessories: * 2-inch kingpin * One galvanized steel front bulkhead, approx. 400 mm high * At the galvanized front connection strip, yellow-red air couplings * Remote axle steering, from front and rear, operated by cable remote control with push buttons, including axle alignment monitoring (without installation on the tractor unit) * Preparation for bolt-on container lockings to accommodate 1 x 20', 1 x 40', or 1 x 45' container on the outer rails. Without container locks * Hydraulic connections from gooseneck to lowbed with a multicoupling instead of screw couplings * Electrohydraulic unit * Spiral cable (approx. 35 mm², approx. 3.5 m in length, max. 250A) for the power supply to the electrohydraulic unit and/or the electric winch, with plug connection (NATO-NATO) between trailer and tractor unit * Yellow reflective tape according to EU regulations, on the sides, extension, and at the rear of the trailer * At the gooseneck front and rear left and right, each with a holder for warning signs, including socket * Manual and documentation on USB stick * Central lubrication system with 2 pumps BEKAMAX (Pico) with standard grease NLGI-2 and removable protection for the pumps * 7 pairs of threaded blocks between the lashing rings under the top flange on the outer rail for mounting screwable RUD rings VLBG-4 * 2nd ride height, approx. 50 mm above standard ride position, selectable via manual control * On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm (L x H). The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) * Separate air connection with air gun on the gooseneck * A stainless steel toolbox, INOX, approx. 1,350 x 400 x 400 mm

Stanje: novo, konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 12.000 kg, dovoljena osna obremenitev (os 2): 12.000 kg, dovoljena osna obremenitev (os 3): 12.000 kg, skupna dolžina: 17.700 mm, skupna širina: 2.990 mm, skupna višina: 3.810 mm, vzmetenje: hidravlika, velikost pnevmatike: 245/70 R17.5 Double Fitted (143/141J), barva: rdeča, Leto izdelave: 2024, Oprema: dvižna zadnja plošča, Color: Red Payload: 100,250 kg Weights: King pin load: 38,000 kg Axle load: 12,000 kg Total axle load: 96,000 kg Gross vehicle weight (GVW): 134,000 kg Unladen weight: 33,750 kg Loading capacity: 100,250 kg Axles: Axle brand: BPW ECO PLUS Hydraulic suspension 7 steered axles (2nd axle rigid) First two axles liftable Drum brakes SN 3020 brakes for ABS, with sensors Tyres: 245/70 R17.5 twin tires Load index 143/141J Dimensions: Length: 17,700 mm Extensions: 19,500 mm Max. extended length: 37,900 mm Loading platform width: 3,990 / 3,450 mm Loading platform height: 1,050 mm +/- 150 mm Height: 3,815 mm Additional information: NATO plug Hydraulically foldable ramps Outriggers + planks for widening the loading platform Electro-hydraulic pump for trailer functions Spare wheel + holder Work lights Rear bumper with lights 2.0” king pin Central lubrication system Lashing rings Wooden loading platform Marker boards for oversize load Remote control = Further information = General information Year of manufacture: 2024 Axle configuration Tyre size: 245/70 R17.5 twin tires (143/141J) Axle brand: BPW ECO PLUS Brakes: drum brakes Suspension: hydraulic suspension Rear axle 1: twin tires; lift axle; max. axle load 12,000 kg; steered; Tyre tread left inside: 100%; left outside: 100%; right inside: 100%; right outside: 100% Rear axle 2: twin tires; lift axle; max. axle load 12,000 kg; Tyre tread left inside: 100%; left outside: 100%; right inside: 100%; right outside: 100% Rear axle 3: twin tires; max. axle load 12,000 kg; steered; Tyre tread left inside: 100%; left outside: 100%; right inside: 100%; right outside: 100% Rear axle 4: twin tires; max. axle load 12,000 kg; steered; Tyre tread left inside: 100%; left outside: 100%; right inside: 100%; right outside: 100% Rear axle 5: twin tires; max. axle load 12,000 kg; steered; Tyre tread left inside: 100%; left outside: 100%; right inside: 100%; right outside: 100% Iiedpsuu E Tijfx Ag Ejf Rear axle 6: twin tires; max. axle load 12,000 kg; steered; Tyre tread left inside: 100%; left outside: 100%; right inside: 100%; right outside: 100% Rear axle 7: twin tires; max. axle load 12,000 kg; steered; Tyre tread left inside: 100%; left outside: 100%; right inside: 100%; right outside: 100% Rear axle 8: twin tires; max. axle load 12,000 kg; steered; Tyre tread left inside: 100%; left outside: 100%; right inside: 100%; right outside: 100% Weights Unladen weight: 33,750 kg Payload: 100,250 kg Gross vehicle weight: 134,000 kg Functional Loading platform height: 105 cm Extendable body: Yes Condition General condition: very good Technical condition: very good Visual condition: very good Financial information Price: On request

Stanje: zelo dobro (rabljeno), konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 12.000 kg, dovoljena osna obremenitev (os 2): 12.000 kg, dovoljena osna obremenitev (os 3): 12.000 kg, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.550 mm, skupna dolžina: 13.600 mm, skupna širina: 2.540 mm, skupna višina: 1.550 mm, vzmetenje: zrak, velikost pnevmatike: 275 / 70 R22.5 – Good Year, barva: rdeča, Leto izdelave: 2024, Color: Red Payload: 60,800 kg Extendable Main Features Manufacturer: Faymonville Type: F-S44-1BBY Triple Extendable Flatbed Chassis Number: YAFSR4009S0036724 Year: NEW / Unused Weights/Loading Capacity King pin load: 28,000 kg Axle load: 12,000 kg Total axle load: 48,000 kg Gross Vehicle Weight (GVW): 76,000 kg Unladen weight: 15,200 kg Payload: 60,800 kg Axles Axle Manufacturer: BPW Air suspension All axles with hydraulic steering WABCO braking system with EBS Tyres: 275/70 R22.5 – Goodyear Load index: 148/145M Dimensions Length: 13,600 mm Extensions: 7,200 mm + 7,400 mm + 7,600 mm Max. extended length: 35,800 mm Load floor width: 2,540 mm Height: 1,550 mm (+/- 100 mm) Additional Information High-resistance metallisation of the steel structure NATO plug connector Lashing rings Stake pockets Wooden load floor Mechanical landing gear Electro-hydraulic pump for trailer functions Spare wheel Rear bumper with lights King pin 2.0" + 3.5" Central lubrication system with 2 BEKAMAX pumps = Further Information = General Information Year of manufacture: 2024 Iiedpfxev I Dqqe Ag Esf Axle configuration Tyre size: 275/70 R22.5 – Goodyear Axle brand: BPW Suspension: Air suspension Rear axle 1: Twin tires; Max. axle load: 12,000 kg; Steered; Tyre tread left inner: 100%; Tyre tread left outer: 100%; Tyre tread right inner: 100%; Tyre tread right outer: 100% Rear axle 2: Twin tires; Max. axle load: 12,000 kg; Steered; Tyre tread left inner: 100%; Tyre tread left outer: 100%; Tyre tread right inner: 100%; Tyre tread right outer: 100% Rear axle 3: Twin tires; Max. axle load: 12,000 kg; Steered; Tyre tread left inner: 100%; Tyre tread left outer: 100%; Tyre tread right inner: 100%; Tyre tread right outer: 100% Rear axle 4: Twin tires; Max. axle load: 12,000 kg; Steered; Tyre tread left inner: 100%; Tyre tread left outer: 100%; Tyre tread right inner: 100%; Tyre tread right outer: 100% Weights Unladen weight: 15,200 kg Payload: 60,800 kg Gross vehicle weight: 76,000 kg Functional Loading platform height: 155 cm Extendable superstructure: Yes Condition Technical condition: Very good Visual condition: Very good

Stanje: zelo dobro (rabljeno), konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 10.000 kg, dovoljena osna obremenitev (os 2): 10.000 kg, dovoljena osna obremenitev (os 3): 10.000 kg, prva registracija: 03/2003, dolžina tovornega prostora: 12.500 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 1.620 mm, skupna dolžina: 12.500 mm, skupna širina: 2.550 mm, skupna višina: 1.620 mm, vzmetenje: hidravlika, velikost pnevmatike: 275 / 70 R22.5, barva: bež, Leto izdelave: 2003, Konfiguracija osi Dimenzija pnevmatik: 275 / 70 R22.5 Znamka osi: SAF Vzmetenje: hidravlično vzmetenje Zadnja os 1: Dvojna montaža; dvigljiva os; največja obremenitev osi: 10.000 kg; krmiljena Zadnja os 2: Dvojna montaža; največja obremenitev osi: 10.000 kg Zadnja os 3: Dvojna montaža; največja obremenitev osi: 10.000 kg; krmiljena Zadnja os 4: Dvojna montaža; največja obremenitev osi: 10.000 kg; krmiljena Zadnja os 5: Dvojna montaža; največja obremenitev osi: 10.000 kg; krmiljena Teže Lastna masa: 13.100 kg Nosilnost: 61.900 kg Dovoljena skupna masa: 75.000 kg Funkcionalno Višina nakladalne površine: 162 cm Stanje Tehnično stanje: zelo dobro Vizualno stanje: zelo dobro Finančne informacije Cena: na zahtevo Iijdpsuu E S Sefx Ag Esf

Stanje: rabljeno, lastna masa: 10.350 kg, največja dovoljena obremenitev: 37.650 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 10/2018, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 245/70 R 17,5, barva: oranžna, Leto izdelave: 2018, obratovalna teža: 10.350 kg, Oprema: ABS,

Stanje: novo, skupna dolžina: 19.000 mm, skupna širina: 600 mm, skupna višina: 450 mm, Leto izdelave: 2022, Colour: Red Load capacity: 430,000 kg Extendable Iiedpfxsuu Hixs Ag Ejf Manufacturer: Faymonville Model: G-Module Vesseldeck Year: 2022 Compatible with Goldhofer THP SL Coupling Heads G-Modul-SL lowbed coupling head Hydraulically extendable Base width: 3,000 mm Hydraulically widenable to 4,700 mm Beam height: 450 mm Coupling length: 1,200 mm Weight: 4,500 kg 4 pairs of lashing rings (LC 16,000 daN) 2 alignment pins Control panel for hydraulic adjustments Colour: RAL 3002 Telescopic Beams 1 pair of telescopic beams Length: 8,000 mm + 5,000 mm Total length: 13,000 mm Construction height: 450 mm Beam width: 450/600 mm Weight: 9,600 kg Lashing rings every 1,000 mm LC 10,000 daN 430 MTO Compression joint at front and rear Colour: RAL 3002 Elongation Beams 1 pair of elongation beams Coupling length: 6,000 mm Construction height: 450 mm Beam width: 450/600 mm Weight: 4,300 kg Lashing rings every 1,000 mm LC 10,000 daN 560 MTO Compression joint at front and rear Colour: RAL 3002 Coupling Pin 1 hydraulic coupling pin for G-Module 1 connecting lines kit for G-Module coupling pin = Further information = Year of manufacture: 2022 Unladen weight: 18,500 kg Overall condition: very good Technical condition: very good Visual condition: very good Price: On request

Stanje: rabljeno, številka stroja/vozila: YAFSR31200001xxxx, Leto izdelave: 2012, Prosimo, na zahtevo navedite referenčno številko: 23457 Tehnične specifikacije: Letnik modela: 2012 EU-odobritev velja do: 28.02.2027 3 osi Dolžina: 1325 cm Neto teža: 12.178 kg Dovoljena največja masa: 59.000 kg 12-tonske osi Vrtljive na vseh osi Pripravljeno za dostavo Opis: 2012 Faymonville Telemax prikolica s platformo, s skupno dolžino 27 m v popolnoma iztegnjenem stanju. Podaljšek znaša 14 metrov. Pripravljeno za dostavo. Tehnični pregled: Da EU-odobritev velja do: 28.02.2027 Lastna teža: 12178 Skupna teža: 59000 Model: telemax prikolica s platformo, z 27-metrskim podaljškom = Dodatne informacije = Iiodpfx Agezqlx Rs Eof Za dodatne informacije se obrnite na ATS Norway.

Stanje: rabljeno, konfiguracija osi: 3 osi, prva registracija: 12/1997, dolžina tovornega prostora: 16.800 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 850 mm, Leto izdelave: 1997, Oprema: ABS, FAYMONVILLE NIZKOPODNOŽJE / RAZTEGLJIVI / AVTOVLEKA / krmilne osi / vitel - - MODEL: STN-3A DMC 38.000 KG LASTNA TEŽA 9.300 KG 3 OSI SAF OSI KRMLJENE OSI VITEL LISTNO VZMETENJE VIŠINA OD TAL 0,85 M VIŠINA DO BALKONA 1,35 M DOLŽINA ZLOŽENE PRIKOLICE 13,2 M DOLŽINA RAZTEGNJENE PRIKOLICE 16,8 M ŠIRINA NAKLADALNA: 2,55 M DOLŽINA BALKONA 4 M PNEVMATIKE: 235/75 R17.5 UVOŽENO NI BILO UPORABLJENO V DRŽAVI 100 % BREZ NESREČ - CENA NETO: 16.900 EUR - - CELOTNA PONUDBA NAŠEGA PODJETJA NA SPLETNI STRANI: MOŽNOST POŠILJANJA PODROBNIH FOTOGRAFIJ IN VIDEA NA WHATSAPP, VIBER ALI E-POŠTO ZA VEČ INFORMACIJ NAS KONTAKTIRAJTE TELEFONSKO. GOVORIMO NASLEDNJE JEZIKE: - Poljsko, angleško, nemško, romunsko, špansko, italijansko, francosko, turško, madžarsko, slovaško, slovensko, ruščino: - ukrajinsko, litovsko, latvijsko, estonsko, uzbeško, gruzijsko, armensko, azerbajdžansko, turkmenistansko, češko: - Isdpfxjybn Iwj Ag Eoif

Stanje: novo, lastna masa: 9.600 kg, največja dovoljena obremenitev: 53.400 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 12.400 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.340 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22.5, barva: siv, Oprema: ABS, Platform area: - Platform with approx. 30 mm thick hardwood flooring - 10 pairs of folding lash rings (outward folding) Landing legs: - JOST landing legs with 2-speed gearbox, 24 t lifting capacity Axles and tyres: - BPW axles, technical capacity 10,000 kg per axle; first axle fixed, all other axles hydro-mechanically forced-steered, mounted on turntables - Air suspension with raise/lower valve - Axle tools included - Tyres: 385/65 R22.5 Braking system: - WABCO brake system in accordance with EU regulations, with EBS-E (4S3M) Steel construction: - Steel structure made from high-tensile fine-grained steels - Steel grades: - S355J2+N / S355MC - S690QL / S700MC Electrical system: - Electrical system according to EU regulations, 24 Volt lighting - ASPÖCK-UNIBOX on the front connection rail with 24N, 24S and 15-pin sockets - Connections according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - First-class and durable corrosion protection of the standard shot-blasted welded frame is ensured by a 2-component zinc-dust primer - High-quality 2-component topcoat, single-colour in Nova Grey - Rear section metallized and painted in RAL 9010 Accessories included: - Platform with approx. 30 mm thick hardwood flooring - 2" king pin - One galvanized steel front wall approx. 1,200 mm high, EN12642-XL - Yellow-red air couplings at the galvanized connection rail at the front - 4 wheel chocks with holders on the front wall - Storage for 1,000 mm plug-in stanchions in the rear central beam - On the gooseneck and rear panel, left and right, a mounting bracket for warning signs with socket - Remote steering from front and rear, operated via cable remote control with push-buttons; with axle tracking control - Electro-hydraulic power pack - White reflective tape as per EU regulations along the side of the trailer, red at rear - 12 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the load bed - European reflective plates at the trailer rear - One bracket for a rotary beacon at the rear of the trailer - One mudflap at the trailer rear - Manual and documentation on USB stick - Central lubrication system BEKAMAX (Pico) with standard NLGI-2 grease and removable protector for the pump - TPMS tyre pressure monitoring system: - The towing vehicle must be capable of transmitting and displaying these data for correct readout Isdporq Dlfofx Ag Eoif - Lift axle on the front axle, automatically controlled by TEBS E in accordance with current axle load and trailer loading status - Radio remote control for the remote steering in addition to the cable remote, with indicator lamps on the receiver for axle tracking control - 5 pairs of crosswise stanchion pocket strips on the bed for 100 x 50 mm plug-in stanchions - 80 km/h speed stickers at rear and both sides - Adjustable access ladder mounted left and right in direction of travel - 2 reversing lights mounted at the rear panel - Load gauge for determining axle loads, including load diagram - HRM metallization of the outer frame: complete steel structure shot-blasted, then all designated visible areas hot metalized with ZINACOR 850 (Zinc 85% - Aluminum 15%)

Stanje: novo, lastna masa: 15.550 kg, največja dovoljena obremenitev: 47.450 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimization of loading platform length, length approx. 3,700 mm - Rear gooseneck with bevel approx. 1,000 mm x 10° Loading Platform: - Extendable loading platform, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° - A recess in the loading platform as well as into the bevel for accommodating the excavator dipper stick - Pneumatic locking with conical locking bolts and reinforced lock positions - Hardwood covering on the loading platform bevel Ramps: - 1 pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm - Ramps with hardwood covering - Hydraulically folding ramp tips - Ramps can be hydraulically shifted individually approx. 235 mm outward and approx. 215 mm inward - Square climbing cleats 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, 1st axle lift-steered, all other axles forced-steered with hydromechanical system - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with raising and lowering valve - Tyres 235/75 R 17.5, twin tires - TPMS tire monitoring system compliant with ECE R141 - TPMS sensors installed in all wheels including spares Accessories included: - Removable steel front wall, approx. 400 mm high - 3kW electro-hydraulic power pack for hydraulic operations, excluding hydraulic winches - Parking position on gooseneck for warning boards when not in use - 1 spare wheel - On the gooseneck: 1 pair of removable side aluminium drop sides, approx. 400 mm high, anodised - On the gooseneck: 1 removable rear aluminium drop side, approx. 400 mm high, anodised - Above the gooseneck: approx. 40 mm thick hardwood floor, chequer plate above king pin - 2" king pin - Guide plate on gooseneck for fifth wheel, approx. 500 mm wide - 4 wheel chocks - Mechanical landing gear with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - 1 intermediate table, approx. 300 mm wide - Extensions (galvanised) extendable by approx. 230 mm per side - Wheel recesses with square climbing cleats - ALU covers for the wheel recesses Ijdpfxek Aht Us Ag Esif - 1 pair of mechanical rear supports - Remote steering at front and rear via cable remote control, with single track monitoring of axles - 1st axle with automatic lift axle function - Central lubrication system with 1 BEKAMAX brand pump - Radio remote control for remote steering, additionally to cable remote, with 2 indicator lights on the receiver as single track monitoring - Wabco Smart Board System - 4 warning boards, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for revolving beacon

Stanje: novo, lastna masa: 15.420 kg, največja dovoljena obremenitev: 61.080 kg, skupna masa: 76.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading Platform: Extendable loading platform with rear chamfer approx. 500 mm x 8° 8 pairs of flip-out lashing rings 1 pair of recessed lashing rings at the front of the loading area Cutouts in the outer frame for securing straps Approx. 48 mm thick hardwood flooring; checker plate above the axles Two-Part Steel Ramps: One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering. Ramps with hydraulically folding ramp sections, hydraulic lifting and hydraulic lateral movement. Max load per pair: 50,000kg. Landing Legs: • JOST landing legs (mechanical) with two-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: BPW axles and suspension, 4th and 5th axle self-steering Technical axle load: 12,000 kg 4th and 5th axle with electromagnetically operated reverse lock, activated by reverse gear and manually Tyres: 235/75 R 17.5 3PMSF Brake System: Brake system according to EU regulations with EBS-E (4S3M) Sockets and Lighting: Electrical system according to EU standards, 24 Volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets Connections per ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component (2K) zinc-rich primer High-quality single-colour 2K topcoat in MB 7350 Novagrau Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Steel Structure: High-strength fine-grained steel construction Steel grades: S355J2+N/S355MC (yield strength 355MPa) Iijdpol Sl Izofx Ag Ejf S690QL/S700MC (yield strength 690MPa) Accessories: One spare wheel with holder in front of the front wall 2" king pin Galvanized steel front wall approx. 400 mm high Yellow-red air couplings on the galvanized front connection panel 2 wheel chocks with holder on the front wall Mounting at the rear of the gooseneck for ALU approach ramps Bracket for beacon at trailer rear Galvanized supports under sloped area of load floor White reflective tape per EU regulations on sides, extension, and red at the rear Electro-hydraulic unit under the rear of loading platform Warning sign brackets including sockets left/right on gooseneck and rear plate Control valves for ramps mounted right side of trailer Mudflap at rear of trailer Manual and documentation on USB stick 3.5" loose king pin supplied On gooseneck: ALU side boards and rear wall, plug-in approx. 2,440 x 400 mm (LxH) Removable rear galvanized stakes (Body length approx. 2,560 mm) 3 pairs WADER container pockets for 1x 20'/30' or 1x 40' container 6 pairs stake pockets for 100 x 50 mm plug-in stakes in outer frame Galvanized extensions, extendable by approx. 230 mm per side Lift axle on front axle, controlled via TEBS E according to actual axle load and current payload Square climbing strips 20 x 20 mm every 200 mm on outer frame chamfer of load floor Checker plate coverings above the king pin and loading area...

Stanje: novo, lastna masa: 10.700 kg, največja dovoljena obremenitev: 38.800 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17,5, barva: sivo-črna, Oprema: ABS, Gooseneck: • Gooseneck with front corners beveled at 45° and rear taper approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Extendable loading platform: • Loading platform in extendable design with rear taper approx. 1,000 mm x 8° • Cut-outs in outer frame of loading platform for attaching tensioning straps • Approx. 48 mm thick hardwood flooring; anti-slip checker plate covering above the axles Two-piece steel ramps: • One pair of galvanized, two-piece steel ramps with approx. 48 mm thick hardwood covering • Ramps with hydraulically foldable ramp sections, hydraulic lift system, and hydraulically adjustable • Maximum load per pair: approx. 40,000 kg Axles and tires: • BPW axles and suspension, 2 rigid axles, 1 self-steering axle • Technical axle load: 12,000 kg • Electromagnetic reverse lock, activated via reverse gear or manually • Air suspension with lift and lower valve • Axle tools • 235/75 R 17.5 3PMSF Braking system: • WABCO braking system according to EU regulations with EBS-E Paintwork: • First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component zinc dust primer • High-quality, single-color top coat in MB 7350 Novagrey applied with two-component paint • Rear section metallized and painted in RAL 9010 Landing legs: • JOST landing legs with 2-speed gearbox for 24t lifting load (50t test load) Steel construction: • Steel construction made of high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC • S690QL/S700MC Electrical system: • Electrical system in accordance with EU regulations, 24 Volt lighting • ASPÖCK-UNIBOX on front connection panel with 24N, 24S & 15-pin sockets Accessories included: • One spare wheel with holder • Galvanized steel front wall approx. 400 mm high • Yellow-red air couplings on the galvanized front connection panel • 4 wheel chocks • Rear mounting bracket for beacon light at the end of the semitrailer • Recess at rear of gooseneck for ALU approach ramps • Galvanized folding supports under the loading platform taper • Cover plates to bridge the gap between ramps and loading platform • White reflector tape per EU regulations on sides, extension, and red at rear • Electro-hydraulic unit at rear, under the loading platform Iiedpfxohlz S Ne Ag Eef • On gooseneck and ramps, left and right, each with a holder for warning signs, including socket • Operating valves for the ramps located on the right side of the trailer • ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) • Four warning panels extendable by approx. 400 mm with a position light • 3 pairs of WADER container pockets in the loading platform for one 20ft, 30ft or 40ft container • 6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading platform • Galvanized extensions, extendable by approx. 230 mm per side • 20 x 20 mm square climbing strips every 200 mm on the outer frame of the platform taper • Painted anti-slip sand layer on checker plates, above king pin and loading platform • Load gauge for axle load measurement, including load diagram • HRM metallization (High Resistance Metallisation) of the outer frame • Complete steel construction shot-blasted, then defined visible surfaces metallized and hot-finished with ZINACOR 850 (Zinc 85% - Alu 15%)

Stanje: novo, lastna masa: 11.000 kg, največja dovoljena obremenitev: 38.500 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm hardwood flooring Load Area: - Extendable loading area with rear taper approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses fitted with square climbing strips 15 x 15 mm, including lower extensions - Between the 1st and 2nd axle, a pair of fixed wheel recesses with cover, approx. 1,610 x 970 x 400 mm - Recess in the bevel as well as protruding into the loading area for parking excavator dipper stick approx. 2,900 x 750 x 210/290 mm - 1 pair of lashing rings, installed flat at the front of the load area (LC 10,000 daN) Iijdpfx Agsup U Hzs Ejf - 5 pairs of folding lashing rings on the outside (LC 5,000 daN) - 2 pairs of folding lashing rings on the outside (LC 10,000 daN) - 2 pairs of lashing rings in the dipper stick recess (LC 5,000 daN) - Cut-outs in the outer frame of the load area for securing straps (LC 2,000 daN) - Incl. three-part removable galvanized covers over the wheel recesses – max. point load 3.5 t / pc. Two-piece Steel Ramps: - One pair of galvanized, two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood surfacing - Ramp with hydraulically folding ramp sections, hydraulic lifting gear, and hydraulically adjustable Axles and Tyres: - BPW axles and suspension, 2 rigid axles, 1 steering trailing axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lifting and lowering valve - Axle tool kit - Tyres 235/75 R 17.5 - TPMS tyre pressure monitoring system in accordance with ECE R 141 Accessories Included: - Mounts for warning signs left and right at the gooseneck and at the rear, each with socket - One spare wheel - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings at the galvanized front connector strip - 4 wheel chocks - Galvanized, extendable outriggers approx. 230 mm per side - Galvanized folding supports beneath the loading area bevel - Rear trailer bracket for rotating beacon - Cover plates for bridging the gap between ramps and load area - White reflective tape to EU regulations, sides and on extensions; rear in red - Electro-hydraulic unit installed at the rear beneath the loading area - Ramp control valves mounted on right trailer side - European reflective panels (red-yellow) on rear of trailer - Four extendable warning boards, approx. 423 x 423 mm, with position light - Bracket for rotating beacon on warning boards - Removable ALU side boards and rear board on gooseneck approx. 2,440 x 400 mm - Rear galvanized removable stakes (structure length approx. 2,560 mm) - 2 pairs of WADER container pockets in loading area for 20ft or 30ft container - 3 pairs of socket pockets for stakes 100 x 50 mm in outer frame of loading area - Removable, galvanized intermediate table with 1 pair of WADER container pockets - Square climbing strips 20 x 20 mm spaced every 200 mm on outer frame at loading bevelling - Painted sand layer on chequer plates of the gooseneck and loading area for anti-slip protection - 80 km/h speed stickers rear and both sides - Load manometer for axle load measurement, including load chart.

Stanje: novo, lastna masa: 9.450 kg, največja dovoljena obremenitev: 35.550 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.500 mm, širina tovornega prostora: 1.560 mm, skupna širina: 2.550 mm, velikost pnevmatike: 385/65 R 22,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck designed as a loading platform with aluminum chequer plate covering - Front chamfered approx. 45° - Hydraulic lifting arm, lifting and lowering range approx. -280/+250 mm - Two king pin positions at DSR 2,300 and 2,000 mm - Compatible with tractor units: 4x2, 6x2, or 6x4 Loading Bay: - Loading bay, length approx. 9,500 mm, fitted with angle profiles at the bottom for pallet accommodation (distance from king pin to center of axle assembly approx. 8,000 mm) Axles, Suspension, and Tires: - BPW axle stubs with drum brakes and independent wheel suspension, hydraulic axle leveling with lifting and lowering function - Lowering lock on axles in case of suspension hose rupture, designed for maximum pallet height of 150 mm - Tires: 385/65 R 22.5 - TPMS tire pressure monitoring sensors installed in all wheels including spare wheels - TPMS system in accordance with ECE R 141 Surface Treatment: - Complete steel structure, shot-blasted automatically after welding - Second blasting with corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for maximum corrosion protection - Final coating with two layers of 2K topcoat, single-color in Novagrau (DB 7350) - Paint system tested with salt spray test according to ISO 9227-NSS; cavity sealing with special wax Included Accessories: - Steel front wall, plug-in, approx. 400 mm high - Toolbox with lid, integrated in the rear area of the gooseneck, approx. 640 x 700 x 215 mm - Plug-in ALU rear wall on the gooseneck, approx. 400 mm high, anodized - 1 pair of foldable ALU side boards on the gooseneck, approx. 400 mm high, anodized - 2" king pin Iedpsygvc Hofx Ag Ejif - 3 pairs of recessed lashing rings on the gooseneck (LC 6,300 daN) - Front connector strip with yellow-red air couplings; illuminated operation for gooseneck, suspension, and hydraulic bracing, with on/off switch - Mechanical drop-leg supports for approx. 48,000 kg support load - Access ladder mounted front right, with 2 plug-in handrails - WABCO Roll Stability Support (RSS) - On the longitudinal beams, 9 pairs of lashing rings (LC 6,300 daN) - On the longitudinal beams, a grating platform level with the load securing rails - Hydraulic preinstallation including control unit for installation of 3 pairs of our hydraulic load restraints - First and last axle, left and right, manually liftable - Storage box behind axle assembly, left and right, splash-water protected - Rear chamfer for easier pallet insertion - Eyes on the rear crossmember for mechanical bracing - 7-pin socket on rear crossmember - Electro-hydraulic unit - 4 wheel chocks with holders - 2 axle load gauges mounted on the left side including axle load chart - 3 pairs of hydraulic load restraints with swivel arm, adjustable on the longitudinal beams - Rear door with cross bracing, hinged left and hydraulically locked right, horizontally lockable at 90°, 105°, and 270° - Folding underrun protection for transporting up to 4 empty standard pallets - 1 spare wheel - License plate bracket with lighting, rear left on trailer - Round NATO socket on the front connector strip (Maeler & Kaege VG 96 917) - Central lubrication system with 1 pump, BEKAMAX brand, standard grease execution

Stanje: novo, lastna masa: 12.300 kg, največja dovoljena obremenitev: 37.200 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear chamfer of approx. 750 mm x 10° - 30 mm thick hardwood flooring Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system Gooseneck: - Gooseneck with rear chamfer of approx. 750 mm x 10° - 3 pairs of lashing rings - 30 mm thick hardwood flooring Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system - Maximum load capacity per pair: 30,000 kg Loading area: Iisdpfx Ajtvfkfsg Eof - Loading area with rear chamfer of approx. 1,000 mm x 8° - Hardwood flooring approx. 48 mm thick, chequer plate flooring above the axles Axles and tires: - BPW axles and suspension, two rigid axles, one self-steering trailing axle - Air suspension with lift and lower valve - The trailing steering axle with electro-magnetic reversing lock, activated by reverse gear or manually - Tyres 235/75 R17.5 3PMSF Included accessories: - 1 spare wheel with holder - TPMS tyre pressure monitoring system according to ECE R 141 - 2" kingpin - One galvanized steel front wall - Yellow-red air couplings on the galvanized front connection rail - 4 chocks with holder on the front wall - Rear mounting area on the gooseneck for ALU approach ramps - 3 heights of aluminium planks - Galvanized folding supports under the loading area chamfer - Height-adjustable tarpaulin body (3,960 mm) - Galvanized front wall with tensioning mechanism for sliding curtain - Height adjustable by approx. 400 mm - "EDSCHA" brand roof, forward-sliding on ALU roof beam profiles, bolted to front and rear walls - 3 pairs of movable stakes in the loading platform - The superstructure is hydraulically extendable at the rear to the left and right by approx. 750 mm - Sliding roof with high-swivelling portal beam - Sliding curtain with 700 mm length surplus, with tensioning straps spaced approx. 600 mm apart - Height to top of the body: approx. 3,960 mm - Driving with open sliding roof is not permitted and will damage the curtain - Cover plates to bridge the gap between ramps and loading area - Rear electro-hydraulic unit under the loading platform - On gooseneck and ramps, each side with one holder for warning signs including socket - Ramp control valves located on right-hand side of trailer - 6 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading area - Lift axle on the front axle - Grating surface in the chamfer of the loading area C40/4 (point load 3.4 t on an area of 20 x 20 cm) - One INOX toolbox 565 x 290 x 810 mm, mounted on the right side in the direction of travel between the axles - Painted sand layer as anti-slip protection on the chequer plates on the gooseneck and loading area - BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable cover for the pump - Four extendable warning signs (approx. 400 mm each) approx. 423 x 423 mm with position light - Axle load gauge including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Entire steel structure shot-blasted, afterwards defined visible surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) hot-refined

Stanje: novo, lastna masa: 29.600 kg, največja dovoljena obremenitev: 72.400 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 6.650 mm, širina tovornega prostora: 2.840 mm, višina nakladalnega prostora: 550 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, obratovalna teža: 29.600 kg, Oprema: ABS, Gooseneck: - Gooseneck hydraulically liftable/lowerable and detachable - Length approx. 3,650 mm - For tractor units: 6 x 4 or 8 x 4 2-axle front bogie: - Hook mountings at front and rear - Bogie length x width approx. 2,200 mm x 2,850 mm Excavator deck "BB-A": - Telescopic excavator deck "BB-A" with drive-over bridge hooks at the front and pin-lug coupling at the rear - Length x base width approx. 6,650 mm x 2,850 mm - Beam height x beam width approx. 400 mm x 1,350 mm - Loading height 550 mm with 150 mm ground clearance 4-axle rear bogie: - Mechanical pin-lug coupling for the installation of a lowbed at the front, rear crossmember at the back - Bogie length x width approx. 5,480 mm x 2,850 mm - Multiple lashing points Pendulum axles and tyres (front and rear bogies): - "PENDULUM AXLE", all axles forced-steered via hydromechanics - Hose rupture valve on axle compensation cylinders with automatic RESET function - Hydraulic cylinders with shut-off valves and locking clips for securing in raised position - Final coating on axles: 2 layers of single-colour MB 7350 Novagrau 2K paint - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres size 285/70 R19.5 Remote steering (after-steering): - Remote steering operable from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Socket for remote steering control on gooseneck - Cable remote control with pushbuttons and single-track control included Accessories included: - Yellow and red air couplings on the galvanised front connection bar - Steel front wall approx. 400 mm high - 4 wheel chocks - 3.5" king pin - One 7-pin socket left and right at rear of gooseneck for warning boards - Hoisting jib with winch for spare wheel at the front face of the gooseneck - Truck hydraulic connection with flow control (40 l/min), including support jib for supply lines; tractor unit tank must have at least 80 litres capacity with couplings - Plug-in ALU side and rear boards on gooseneck, approx. 400 mm high, anodised - Control lever on gooseneck protected by foldable cover - Separate air connection with air gun on gooseneck - BEKAMAX central lubrication system: 1x on gooseneck, 1x on 2-axle and 1x on 4-axle bogie - Variomax tool kit - Multi-coupling hydraulic connectors on gooseneck and at lowbed hook interface - 2 spare wheels - One 7-pin socket left and right, at front and rear of rear bogie for warning boards - Front bogie with separate air connection for impact wrench - Foldable steel bed extensions, adjustable in width from approx. 2,850 mm to 3,250 mm - Steel bed inserts can be placed in 2 positions for sunken load area - Steel mats with rubber flooring, approx. 12 mm thick - Thread-in options (⌀ 40 mm) every approx. 500 mm on the upper flange of the excavator deck outer tube for eye bolts - One locking point at every approx. 500 mm on extension with mechanical lock - Socket on rear bogie for remote steering cable control - 2 reversing lights on rear panel Ijdpfx Agowcmhas Eoif - Four extendable warning boards (by approx. 2,000 mm), each approx. 423 x 423 mm with position lights - 1 work light left + right on rear panel of gooseneck with separate on/off switches - Two INOX toolboxes, approx. 855 x 340 x 390 mm - 1-cylinder Hatz diesel engine (Silent Pack) - Radio remote control for after-steering

Stanje: novo, lastna masa: 10.300 kg, največja dovoljena obremenitev: 39.200 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Platform: - Loading platform after the gooseneck, hydraulically liftable and lowerable, length approx. 2,800 mm, with rear chamfer approx. 1,000 mm x 8° - Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, over the axles with chequer plate covering Two-part Steel Ramps: - One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp parts, hydraulic lifting system, and hydraulically adjustable - Maximum load per pair: 40,000 kg Axles, Suspension and Tires: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated by reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tires 235/75 R 17.5 3PMSF - TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories Included: - One spare wheel with holder in front of the bulkhead Iodpfxeu Hp Hro Ag Eoif - 2" kingpin - One galvanized steel front wall approx. 400 mm high - Yellow-red air couplings at the galvanized connection strip in front - 4 wheel chocks - Galvanized folding supports under the platform's rear chamfer - A holder for a rotating beacon at the rear of the trailer - Cover plates to bridge the gap between ramps and platform - White reflective tape as per EU regulations along the sides of the trailer and red at the rear - Electro-hydraulic unit at the rear, under the platform - At the gooseneck and at the ramps left and right, each with a holder for warning signs, including socket - Control valves for the ramps positioned on the right side of the trailer - European reflective plates (red-yellow) at the rear of the trailer - Manual and description on USB stick - Removable ALU side walls and rear wall on the gooseneck approx. 2,440 x 400 mm - The rear, galvanized side stakes are removable (body length approx. 2,560 mm) - An electric cable winch with radio remote control, approx. 5,400 kg lifting force, including 9.5 mm steel cable, 24 m long, with guide roller - Bolted 5 t ring for cable deflection of the winch on the gooseneck without pulley - 2 pairs WADER container pockets in the platform for a 20ft container - 6 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the platform - Lift axle on the front axle with control via TEBS E, depending on actual axle load and loading condition - 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN) - 1 pair of recessed lashing rings along the central beam at the rear chamfer (LC 10,000 daN) - Sand coating for slip resistance painted on the chequer plates on the gooseneck and on the platform - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and removable pump protection - Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm - Speed stickers 80 km/h rear and on both sides - Load manometer for determining axle loads including load chart - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then all defined visible surfaces metallized and hot-coated with ZINACOR 850 (zinc 85% - alu 15%)

Stanje: novo, lastna masa: 10.900 kg, največja dovoljena obremenitev: 37.100 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 890 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, obratovalna teža: 10.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the loading platform length, approx. 3,700 mm long, rear bevel approx. 1,000 mm x 6° - Technical king pin load: 18,000 kg - For tractor units: 4 x 2 and 6 x 2 Loading platform: - Loading platform, approx. 9,600 mm long with rear taper approx. 900 mm x 6° - Platform area behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, with a load capacity of up to approx. 9,000 kg - Grating surface and steel sheet floor approx. 5 mm thick as additional reinforcement on the sloped section of the platform Ramps: - One pair of two-section AXS steel ramps, approx. 4,675 mm long and approx. 900 mm wide - Grating surface - Hydraulically folding ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 365 mm inward - Painted sand coating on the outer frame and ramp tips - Flashing lights on the outer sides of the ramp tips with control switch next to the ramp operation panel - Ramp lock in transport position with quick-release fastener Axles, suspension and tires: - BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steerable (trailing) - 1st axle with traction assistance - Operated via brake pedal in the tractor unit - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 - TPMS tire pressure sensors installed on all wheels including spare wheels Brake system: - WABCO EBS-E braking system in accordance with EU regulations Paintwork: - Trailer MB 7350 Novagrau Equipment included: - Removable front steel wall, approx. 400 mm high - 3 kW electro-hydraulic power unit for hydraulic operations, except for hydraulic winches - Gooseneck guide plate for the fifth wheel, approx. 500 mm wide - JOST Module B – static test load = 50,000 kg - Continuous grating with 5 mm steel underlay as additional reinforcement - Painted sand coating - Cutouts in the outer frame of loading platform and lift bed for hooking hydraulic ramp control valves on the right-hand side of the vehicle - 2" king pin Ijdpfx Aeuadk Nsg Ejif - Central lubrication system with 1 pump, brand BEKAMAX - 1 pair of plug-in ALU side boards on the gooseneck, approx. 400 mm high, anodised - Electric winch, approx. 5,400 kg pulling force, with radio remote control - Steel wire rope approx. 24 m long, rope diameter approx. 9.5 mm, including rope pressure roller - WABCO Smart Board system - 4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, lastna masa: 13.500 kg, največja dovoljena obremenitev: 51.500 kg, skupna masa: 69.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimizing loading platform length, length approx. 3,700 mm Gooseneck rear with chamfering approx. 1,000 mm x 10° Loading Platform: Telescopic loading platform, length approx. 8,800 mm, with rear chamfering approx. 500 mm x 10° Recess in the chamfer as well as into the loading platform to accommodate the excavator dipper stick Pneumatic locking with conical pin and reinforced locking positions Supply lines routed protected within the extendable beam, adapting to the respective platform length Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps individually adjustable hydraulically approx. 235 mm to the outside and approx. 215 mm to the inside Axles and Suspension: BPW axles and suspension, two rigid axles, two steering trailing axles Electromagnetic reverse lock, activated via reverse gear and manually Air suspension with lift and lower valve Axle tool Tyres: 235/75 R17.5 3PMSF twin tyres Load index: 143/141J (144/144F) Brake System: WABCO braking system, EBS-E in accordance with EU regulations Lighting System: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Metalizing: Standard HRM metallization of the outer frame Complete steel structure shot-blasted, then visible defined surfaces metallized with ZINACOR 850 (Zinc 85% - Alu 15%) hot-refined Iiodpfxok Ahugj Ag Esf Steel Construction: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified as per DIN-EN 287-1 MAG welding process according to EN ISO 4063 Shielding gas M21 as per EN ISO 14175 Accessories Included: Front wall made of steel, plug-in, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin 24N connection per ISO-11852, 24S connection per ISO-3731, 15-pin connection per ISO-12098 Round NATO socket on the front connection strip Cable to supply electro-hydraulic unit and/or electric winch (35 mm², 3.5 m long) between trailer and tractor with connector (NATO-NATO) 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches 1 spare wheel with mounting adapter Outer beam of the gooseneck with fastening holes for screwable lashing rings. The first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included One fastening hole in the rear upper area of the gooseneck's outer beam for a screwable lashing ring 1 pair of screw-in lashing rings Approx. 40 mm thick hardwood covering above the gooseneck On the gooseneck, 1 pair of plug-in side aluminium walls, approx. 400 mm high, anodized On the gooseneck, a plug-in aluminium rear wall, approx. 400 mm high, anodized 2" kingpin Gooseneck guide plate for fifth wheel, approx. 500 mm wide 4 wheel chocks with holder Holder for aluminium approach ramps Mechanical landing gear with 2-speed gearbox and crank Continuous hardwood floor approx. 50 mm thick on the loading platform, interrupted between axles Platform locking with conically welded locking profiles every 250 mm incl. tension plate Slotted holes at the front of the loading platform for attachable and adjustable bridging elements 1 intermediate table with recessed platform, approx. 300 mm wide for the draw-out tube with large cross-section, with sheet metal covering Front and rear with slotted holes

Stanje: novo, lastna masa: 17.500 kg, največja dovoljena obremenitev: 43.500 kg, skupna masa: 61.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.750 mm, višina nakladalnega prostora: 400 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - For tractor units: 6x4 or 8x4 Lowbed: - Lowbed with external beams, extendable version, "SUPER LOW" design, approx. 7,550 mm long - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking device - Service lines are protected within the extendable beams and automatically adjust to the lowbed length Rear Undercarriage: - Rear chassis with closed outer frame, checker plate cover, and continuous prism-shaped excavator trough approx. 1,450/900 x 505 mm, open at the rear - 2 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame Ijdpfx Aeh Hm Theg Ejif Axles and Tires: - "PENDULUM AXLE", all axles hydro-mechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 / 3PMSF Included Accessories: - Prepared for bolt-on container positioning for 1x 20ft or 1x 40ft container on the outer beams - 2" kingpin - Galvanized steel front wall approx. 400 mm high - One spare wheel with holder - At the galvanized front adapter bar yellow-red air couplings - 4 wheel chocks - Remote rear steering from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Hydraulic line connections from gooseneck to lowbed with multi-coupling instead of screw coupling - Electro-hydraulic power pack - White reflective tape to EU specifications on sides, extension, and rear red - 2 wooden blocks 500x250x200 mm - European reflective plates (red-yellow) on the trailer rear - At the gooseneck and rear wall left and right each a bracket for warning boards including socket - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 - Load gauge for determination of axle loads including load diagram - On the gooseneck, plug-in ALU side and rear boards approx. 2,000 x 400 mm - The rear galvanized insert posts are removable (body length approx. 2,120 mm) - Separate air connection for air gun on the gooseneck - Duomatic air coupling from gooseneck to lowbed - Rear upper section of gooseneck closed with removable cover - 1 pair of steel ramps to bridge the lowbed's pick-up hooks - Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm - Wireless remote control for rear steering in addition to cable remote, with signal lights at receiver for single-track monitoring - 6 pairs of threaded blocks between lashing rings under the top chord on the outer beams for mounting screwable RUD rings VLBG-4 - 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading bed - Foldable extensions, approx. 230 mm per side - Loading area features a painted sand layer for anti-slip protection - Dipper stick trough of rear chassis closed at front and rear with plug-in plates - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - alu 15%)

Stanje: novo, lastna masa: 13.250 kg, največja dovoljena obremenitev: 47.550 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, vzmetenje: zrak, velikost pnevmatike: 245/70 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings 30 mm thick hardwood flooring Extendable loading platform: Loading platform in extendable design with rear chamfer approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings 3 pairs of outward-folding lashing rings 1 pair of flat lashing rings at the front of the loading area Cut-outs in the outer frame of the loading area for inserting tension straps Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Two-part steel ramps: One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering. Ramp with hydraulically folding and unfolding parts, hydraulic lifting system, and hydraulically adjustable position. Maximum load per pair: 40,000 kg Landing legs: JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced-steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool Tires 245/70 R 17.5 Braking system: Braking system according to EU regulations with EBS-E (4S3M) without connecting lines to tractor unit Ijdpfx Agsl Uxdke Eoif Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer High-quality one-color two-component (2K) top coat in Novagrau Rear section metallized and painted in RAL 9010 (pure white) Metallic paint not possible Electrical system: Electrical system according to EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connections conforming to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" kingpin One galvanized steel headboard approx. 400 mm high At the galvanized front connection strip, yellow-red air couplings 4 wheel chocks with holders at the headboard One spare wheel with holder in front of the headboard Electro-hydraulic power unit Rear and front remote steering via cable remote control with push-buttons, with single-track control of the axles Bracket at rear of gooseneck for ALU drive-on ramps European reflector signs (red-yellow) at trailer rear White reflective tape according to EU regulations at the sides, at the extension, and red at the rear At the gooseneck and on the ramps left and right, each with a holder for warning signs including socket One holder for beacon at trailer rear Galvanized folding supports under the loading platform chamfer Ramp operating valves fitted on the right side of the trailer Cover plates to bridge the gap between ramps and loading platform One mudflap at trailer rear Manual and description on USB stick Central lubrication system BEKAMAX (Pico) with general-purpose grease NLGI-2 and removable pump guard On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm The rear galvanized stakes are removable, superstructure length approx. 2,560 mm One INOX toolbox 1,350 x 400 x 400 on the gooseneck, box covers oil filler cap 4 pairs of WADER container pockets in the loading area for a

Stanje: novo, lastna masa: 17.250 kg, največja dovoljena obremenitev: 48.700 kg, skupna masa: 66.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 375 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 17.250 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize loading platform length, approximately 3,750 mm long Isdpfsh Hm Tzex Ag Eoif - Gooseneck hydraulically liftable, lowerable, and detachable - For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Lowbed: - Lowbed with external beams, designed as a telescopic vessel bridge in low-profile construction with front extension - Length x width approx. 7,550 mm x 2,740 mm - Mechanical locking of the extension Chassis: - Rear chassis with closed outer frame - Checker plate surface and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, Suspension, and Tyres: - “PENDEL-AXLE”, all axles hydromechanically forced steered - Burst protection valve on the axle compensation cylinders with automatic reset function - Hydraulic cylinders with shut-off valves and plug pins for securing in raised position - Final coating of axles: two coats of single-color 2-component paint in "FAY-Grey-34-0260" - Technical axle load 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 Accessories: - Detachable steel front wall, approx. 400 mm high - 4 wheel chocks - Rear upper gooseneck area closed with removable cover - 1 pair of steel ramps with climbing bars and locking bolts to bridge the lowbed mounting hooks - Ramps can be positioned over or between the hooks - Mounting options for steel drive-on ramps at the rear, between the outer beams of the gooseneck - Locking point approx. every 1,000 mm on the extension - 1 lashing ring each, left and right, on the front cross member - Supply line connection strip for tractor unit, mounted at the height of outer frame profile - 6 pairs of threaded blocks on the exterior of the load floor inner beams for attaching M24 screw rings - 6 pairs of recessed lashing rings on the outside of the load floor outer beams, foldable inwards and outwards - 1 pair of threaded blocks on the front and rear of the load floor outer beams for M24 screw rings - Mounting rail for loose aluminum approach ramps on the end cross member of the vehicle - Central lubrication system with 2 pumps, brand BEKAMAX - Remote steering front and rear, cable remote controlled, with axle tracking control - 3 kW electro-hydraulic power unit for hydraulic operations, except hydraulic winches - Removable galvanized loading floor, can be placed in 3 elements between the outer beams, with hardwood covering - Foldable extensions, approx. 230 mm per side - Loose extension boards, steel-edged - 4 warning signs approx. 423 x 423 mm - Radio remote control for rear steering - 3.5” kingpin - Anti-slip coating on the left chamfer of the gooseneck - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Guide plate from gooseneck for the fifth wheel plate, approx. 800 mm wide - 1 spare wheel with mounting adapter - Parking position on the gooseneck for warning signs when not in use - 2 pairs of stake pockets integrated into the chassis outer frame, for plug-in stakes approx. 100 x 50 mm - Excavator stick trough of rear chassis closed at the rear with a removable plate - Trailer color: Mercedes-Benz 7350 Novagrey

Stanje: novo, največja dovoljena obremenitev: 49.000 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with front corners chamfered at 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Extendable Loading Platform: - Loading platform, extendable design with rear chamfer of approx. 1,000 mm x 8° - 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) - 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - 1 pair of horizontal lashing rings at the front of the loading platform (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for securing straps (LC 2,000 daN) - Hardwood flooring approx. 48 mm thick, checker-plate covering above the axles Two-Part Removable Ramps: - One pair of galvanized two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp sections, hydraulic lifting mechanism, and hydraulic side-shift - Maximum load per pair: 40,000 kg Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Axles and Tyres: - BPW axles, two fixed axles and two steering axles (self-steering), air suspended, with drum brakes, raise/lower function - Self-steering axles with electro-magnetic reverse lock, can be activated by reverse gear or manually - Axle tool kit - Tyre size 235/75 R 17.5 Brake System: - Braking system according to EU regulations with EBS-E (4S3M) Steel Structure: - Steel structure made of high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Isdsh Etf Rspfx Ag Esif Paintwork: - First-class, long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component (2K) zinc dust primer - High-quality single-tone topcoat using 2-component (2K) paint in Nova grey Electrical System: - Electrical system according to EU regulations, 24 volt lighting, ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX on the front connector strip with 24N, 24S, and 15-pin sockets Included Accessories: - 2" kingpin - Galvanized steel front wall, approx. 400 mm high - One spare wheel with holder in front of the headboard - Yellow-red air couplings on the galvanized front connector strip - 4 wheel chocks with holders on the front wall - Mount at the rear section of the gooseneck for ALU approach ramps - Galvanized folding supports underneath the loading platform chamfer - One holder for warning beacon - Cover plates to bridge the gap between ramps and loading platform - White reflective tape on the side, red on extension and rear, according to EU regulations - Electro-hydraulic power unit - At the gooseneck and ramps (left/right) a holder each for warning signs including socket - Control valves for the ramps mounted on the right side of the trailer - One mud flap at the rear of the trailer - Manual and documentation on USB stick - On the gooseneck, plug-in ALU side boards and rear wall approx. 2,440 x 400 mm - Rear galvanized plug-in stakes are removable (body length approx. 2,560 mm) - 4 pairs of WADER container pockets in the loading platform for one 20ft, two 20ft or one 40ft container - 7 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading platform - Galvanized, extendable platform wideners approx. 230 mm per side - Lift axle on the front axle with control system - 20 x 20 mm square climbing bars - BEKAMAX central lubrication system - Four warning signs extendable by approx. 400 mm eac

Stanje: novo, lastna masa: 12.900 kg, največja dovoljena obremenitev: 34.100 kg, skupna masa: 47.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 350 mm, vzmetenje: drugo, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 12.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm in length - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2, and 6x4 Loading Platform: - Low-bed with external beams, extendable “SUPER LOW” design, approx. 6,850 mm in length - Low-bed with fixed hardwood flooring, approx. 40 mm thick, with mechanical locking device Rear Chassis: - Rear chassis with closed outer frame, chequer plate covering, and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings, foldable to the outside - 1 pair of lashing rings recessed in the trough - 2 pairs of stake pockets for insertable stakes 100 x 50 mm in the external frame Pendulum Axle and Tyres: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and safety locking pins for securing in raised position - Axles painted with two layers of single-colour 2K paint in “FAY-Grey-34-0260” - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 Ijdpfxshlz R Se Ag Esif - TPMS tyre pressure monitoring system according to ECE R 141 Accessories: - Preparation for the installation of bolt-on container locators for 1 x 20ft or 1 x 40ft container on the outer girders - 2" king pin - One galvanized steel front wall, approx. 400 mm high - One spare wheel - Yellow-red air couplers on the galvanized front connection bar - 4 wheel chocks - Remote steering from front and rear, operable via wired remote control with push buttons, with single-track alignment control - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of screw couplings - Electro-hydraulic power unit - White reflective tape in accordance with EU regulations on sides, extension, and rear - European reflective plates (red-yellow) on the rear of the trailer - One bracket on each side of gooseneck and rear plate for warning panels, including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on outer beam for mounting screw-on RUD Rings VLBG-4 - Detachable ALU side boards and rear board on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized insertable stakes are removable (body length approx. 2,560 mm) - Gooseneck rear upper area covered with removable cover - 5 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading area - Folding extensions, approx. 230 mm per side - 2 pairs of bolted RUD Rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the mounting hooks of the low-bed - Anti-skid sand layer painted on loading surface - 80 km/h speed stickers at rear and both sides - Spoon boom trough at rear chassis closed at rear with plug-in plate - Four extendable warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for rear axle steering in addition to cable remote, with indicator lights on receiver for alignment control - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard NLGI-2 grease - Load pressure gauge for determining axle loads - HRM Metallisation (High Resistance Metallisation) of outer frame - Complete steel structure shot blasted, then all defined visible areas metallized and finished with ZINACOR 850 (zinc 85% - aluminium 15%) hot galvanizing

Stanje: novo, največja dovoljena obremenitev: 38.100 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.100 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5 3PMSF, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer of approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading platform: 5 pairs of fold-out lashing rings 3 pairs of fold-out lashing rings 1 pair of horizontal lashing rings at the front of the loading area Cut-outs in the outer frame of the loading surface for hooking in tension belts Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Landing legs: JOST landing legs with 2-speed gears for a 24 t lifting capacity Axles and tyres: BPW axles, two axles are fixed, two axles are self-steering, air-suspended, with drum brakes, with lift/lower function The self-steering axles come with an electro-magnetic reverse lock, which is activated via reverse gear or manually Axle toolkit Tyres: 205/65 R17.5 3PMSF Brake system: WABCO brake system according to EU regulations with EBS-E Steel construction: Iodpfjtphtmsx Ag Ejif Steel structure made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Electrical equipment: Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK lighting ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component zinc dust primer High-quality single-colour 2-component top coat in MB 7350 Novagrau No metallic paint possible Rear section metallized and painted in RAL 9010 Accessories included: 1 spare wheel 205/65 R 17.5 TPMS tyre pressure monitoring system acc. to ECE R 141 At the galvanized front connection strip yellow-red air couplings 4 wheel chocks with holder on front wall Bracket at rear of gooseneck for ALU access ramps Galvanized folding supports under the chamfer of the loading surface Mount for a revolving beacon at the rear of the trailer Height-adjustable curtain structure Galvanized front wall with a tension mechanism for the sliding curtains Height-adjustable by approx. 400 mm "EDSCHA" brand roof, sliding forward on ALU roof beam profiles, bolted to the front and rear wall In the loading surface, 3 pairs of sliding stakes Superstructure at rear hydraulically extendable to left and right by approx. 750 mm Sliding roof with upward swinging portal carrier Sliding tarp with 700 mm reserve length, with tension straps at intervals of approx. 600 mm Height to top edge of superstructure approx. 3,960 mm Journeys with the sliding roof open are not permitted and will damage the tarp Mounting rail for ALU access ramps at the rear of the vehicle At the gooseneck and at the rear panel left and right, each with a mount for warning signs incl. socket A mud flap at the rear of the trailer European reflector plates at the rear of the trailer 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading area Lifting axle on the front axle controlled by TEBS E depending on current axle load and load status Rear structure with closed ALU double-wing doors A sanded, anti-slip paint layer on the checker plates on the gooseneck and on the loading surface BEKAMAX centralized lubrication system with standard grease NLGI-2 and a removable guard around the pump Speed stickers 80 km/h on rear and both sides Load manometer for axle load determination including load chart