Faymonville Ilo-3 Innenlader, 9.550Mm, Mehrfach Auf Lager nakup rabljenega (41.066)

Stanje: novo, skupna masa: 78.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 850 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck in SNT design to optimize loading area length, approx. 3,700 mm long, rear with a bevel approx. 1,000 mm x 10° • For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading Area: • Extendable loading platform, approx. 8,800 mm long with rear bevel approx. 500 mm x 10° • A recess in the platform and rear bevel to accommodate the excavator dipper stick, approx. 3,950 x 580 x 370/450 mm Ramps: • One pair of two-piece steel ramps, approx. 4,350 mm long and 900 mm wide • Hydraulically folding ramp tips • Ramps hydraulically adjustable separately approx. 235 mm outwards and approx. 215 mm inwards • Hardwood decking on the beveled part of the loading area • Ramp with hardwood decking • 20 x 30 mm square climbing strips, approx. every 200 mm on the outer frame of the ramp Axles and Tyres: • TWINAXLE-II independent wheel suspension with BPW stub axles, 1st axle steered in advance, all other axles are hydromechanically forced steered • 1st axle with electromagnetic reverse lock via reverse gear and manual activation • Technical axle load: 12,000 kg • Hydr. axle compensation, hydraulic cylinders with shut-off valves • Tyres 245/70 R 17.5 • TPMS tyre pressure monitoring system according to ECE R 141 Accessories Included: • Plug-in steel front wall, approx. 400 mm high • 4 wheel chocks with holder • Front connection bar with yellow-red air couplings • 3 kW electro-hydraulic power pack for hydraulic control, except for hydraulic winches Pgedpfx Aiorvw U Se Rel • 1 spare wheel • 2 pairs of screw-in lashing rings • 1 pair of horizontal lashing rings in the rear area of the gooseneck • On the gooseneck: 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized • On the gooseneck: 1 plug-in ALU rear board, approx. 400 mm high, anodized • Approx. 40 mm thick hardwood decking on the gooseneck, checker plate over the king pin • 3.5" king pin • Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide • Load area locking with conically welded arresting profiles every 250 mm • Incl. pre-tensioning plate • 1 pair of lashing rings on the front cross member • 8 pairs of recessed, fold-out lashing rings in the outer frame of the platform • Extendable (galvanized) widenings approx. 230 mm per side • 1 pair of fixed open wheel recesses up to extension, approx. 700 x 410 mm, in the platform in front of the 1st axle • Wheel recesses with checker plate covering and 15 x 15 mm square climbing strips, approx. every 200 mm • 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm, in the platform between the 1st and 2nd axle • Wheel recesses with 15 x 15 mm square climbing strips and widenings in the lower section • ALU covers for the wheel recesses between 1st and 2nd axle, which can also be used as broadening planks • 1 pair of mechanical rear supports • 20 x 30 mm square climbing strips, approx. every 200 mm on the outer frame of the bevel of the loading area • Central lubrication system with 1 pump, BEKAMAX brand, standard grease as per NLGI-2 • Radio and cable remote control, with 2 indicator lights on the receiver for single wheel control • WABCO Smart Board system • The Smart Board is equipped with an odometer • 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and mounts for rotating beacon

Stanje: novo, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.700 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 890 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimizing loading area length, approx. 3,700 mm long, with rear tapering of approx. 1,000 mm x 6° - For tractor units: 4 x 2 and 6 x 2 Loading platform: - Loading platform, approx. 9,700 mm long, with hydraulically foldable and lowerable rear section as well as hydraulically liftable front section for driving onto the gooseneck Axles and tyres: - BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle self-steering - 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually - Technical axle load: 12,000 kg - Air suspension with lift/lower valve - 235/75 R 17.5 3PMSF twin tyres - TPMS tyre pressure monitoring system according to ECE R 141 BPW Auto Reverse Control: - Electrohydraulic auxiliary steering for the self-steering axle of a 3-axle unit - Automatic control of the self-steering axle when reversing via gyroscope sensor - Manual steering operation in forward and reverse using separate radio remote control - Manual operation enabled up to 10 km/h - System powered by separate electro-hydraulic unit Accessories included: - Removable steel front wall, approx. 400 mm high - 3 kW electro-hydraulic power pack - External beams on gooseneck with mounting holes for bolted lashing rings - First mounting hole approx. 200 mm from front, then approx. every 400 mm - One mounting hole at upper rear of external gooseneck beams for a bolted lashing ring - Grating cover with 5 mm sheet reinforcement on gooseneck and rear taper - 2" king pin - Guide plate on gooseneck for fifth wheel plate, approx. 500 mm wide - Round NATO socket at front connection bar (Maeler & Kaege VG 96 917) - 1 pair of removable side aluminium drop sides on gooseneck, approx. 400 mm high, anodized - 4 wheel chocks - Electric winch, approx. 5,400 kg pulling force, with radio remote control - Wire cable approx. 24 m long, cable ø approx. 9.5 mm, including cable pressure roller - Winch installed at the front inside the gooseneck - Continuous grating cover with 5 mm steel underlay for additional reinforcement, designed for point loads: - on the lift bed - on the loading platform - on the hydraulically lowerable rear section - Painted-on sand coating on the gooseneck covering plates and in transition areas between neck and lift bed, between lift bed and loading platform, and between loading platform and ramps - 1 spare wheel - Hydraulic lift bed, approx. 2,500 mm long, load capacity while driving in raised position: 9,000 kg - Hydraulic cylinders are fitted with load-holding valves - Cut-outs in the outer frame of the loading platform and lift bed for attaching tension straps - Extensive lashing positions - Hydraulically lowerable rear section for loading and unloading, can be raised to shorten total coupling length - Load capacity while driving in horizontal position: 10,000 kg - Shortening of total coupling length when raised: 2,350 mm - Painted-on sand coating on the complete ramp, except for the extendable galvanized part of the ramp - Hydraulically extendable rear extensions for loading and unloading - Radio remote control: Psdpfjyw Sakjx Ai Regl - Control of hydraulic lift bed - Control of hydraulic lifting of rear extension - Control of hydraulic extension of rear extension - 1st axle with starting aid - Centralized lubrication system with 1 pump - 4 warning signs, approx. 423 x 423 mm, extendable

Stanje: novo, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.700 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 890 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimal load deck length, length approx. 3,700 mm, rear end with chamfer approx. 1,000 mm x 6° - For tractor units: 4 x 2 and 6 x 2 Load deck: - Load deck, approx. 9,700 mm long with hydraulically folding and lowering rear section, as well as hydraulically liftable deck at the front for driving over the gooseneck Axles and Tyres: - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle steering on trailing arm - 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manual switch - Technical axle load: 12,000 kg - Air suspension with lifting and lowering valve Pedoyw R Sropfx Ai Rogl - 235/75 R 17.5 3PMSF twin tyres - TPMS tyre pressure monitoring system compliant with ECE R 141 Included accessories: - Plug-in steel front wall approx. 400 mm high - Yellow-red air couplings on the front connection rail - 3 kW electro-hydraulic power pack for control of hydraulic functions, except hydraulic winches - Outer beams on the gooseneck with fixing holes for screwable lashing rings - First hole approx. 200 mm from front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - One mounting hole on the upper rear area of the outer beams of the gooseneck for a screwable lashing ring - On gooseneck and rear chamfer, grating covering with 5 mm plate reinforcement - 2" kingpin - Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide - Round NATO socket on the front connection rail (Maeler & Kaege VG 96 917) - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodised - 4 wheel chocks - Electric cable winch, approx. 5,400 kg pulling force, with remote control - Wire rope approx. 24 m long, rope diameter approx. 9.5 mm, incl. rope pressure roller - Winch mounted at the front inside of the gooseneck - Plastic tarpaulin cover for the winch - Mechanical landing gear with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - Continuous grating covering with 5 mm plate reinforcement for additional strength, designed for point loads: - on the lifting bed - on the load deck - on the hydraulically lowerable rear section - Painted-on sand coating on the gooseneck covers and transitional areas between neck and lift bed, between lift bed and load deck, and between load deck and ramps - 1 spare wheel with mounting adapter under the load deck on the right in front of the axles - Hydraulic lifting bed, length approx. 2,500 mm, load capacity in driving position (raised): 9,000 kg - Hydraulic cylinders fitted with load-holding valves - Cut-outs in the outer frame of the load deck and lifting bed for lashing straps - Extensive lashing positions - Hydraulically lowerable rear section for loading/unloading and can be raised to reduce overall train length - Load capacity in driving position (horizontal): 10,000 kg - Reduction of overall train length when raised: 2,350 mm - Painted-on sand coating on the entire ramp, except for the extendable galvanised ramp section - Hydraulic, extendable rear extensions for loading and unloading - Remote control: - Lifting bed operation - Lifting device for rear extension operation - Extension of rear extension operation - 1st axle with traction aid - Central lubrication system with 1 pump - 4 warning boards, approx. 423 x 423 mm, extendable

Stanje: rabljeno, konfiguracija osi: 3 osi, prva registracija: 10/2006, skupna širina: 2.850 mm, vzmetenje: drugo, velikost pnevmatike: 285/70R19.5, barva: črn, Leto izdelave: 2006, Oprema: ABS, = Additional Options and Equipment = - Central lubrication = Remarks = Pgedpfjxbng Eox Ai Rsl Faymonville Jeep Dolly D3 Year: 10-2006. 1 x lift axle. 1 x friction-steered axle (trailing steering axle). Air suspension. Maximum technical weight: 56,000 kg. Faymonville STBZ-5VA Year: 10-2006. Pendulum axles. Removable gooseneck. Movable platform. Extendable load bed: 400 cm. Load bed dimensions: 650 + 400 cm. Gooseneck load capacity: 50,000 kg. Maximum technical weight: 119,680 kg. = Further Information = Axle Configuration Tyre size: 285/70R19.5 Brakes: Drum brakes Front Axle 1: Twin tires; Left inside tread: 15%; Left outside: 60%; Right inside: 60%; Right outside: 60%; Suspension: Air suspension Front Axle 2: Twin tires; Left inside tread: 30%; Left outside: 30%; Right inside: 40%; Right outside: 60%; Suspension: Air suspension Front Axle 3: Twin tires; Steered; Left inside tread: 30%; Left outside: 70%; Right inside: 60%; Right outside: 70%; Suspension: Air suspension Rear Axle 1: Twin tires; Steered; Left inside tread: 30%; Left outside: 60%; Right inside: 40%; Right outside: 70%; Suspension: Hydraulic suspension Rear Axle 2: Twin tires; Steered; Left inside tread: 50%; Left outside: 50%; Right inside: 30%; Right outside: 75%; Suspension: Hydraulic suspension Rear Axle 3: Twin tires; Steered; Left inside tread: 60%; Left outside: 60%; Right inside: 60%; Right outside: 60%; Suspension: Hydraulic suspension Rear Axle 4: Twin tires; Steered; Left inside tread: 60%; Left outside: 60%; Right inside: 40%; Right outside: 50%; Suspension: Hydraulic suspension Rear Axle 5: Twin tires; Steered; Left inside tread: 70%; Left outside: 70%; Right inside: 20%; Right outside: 70%; Suspension: Hydraulic suspension Weights Unladen weight: 36,600 kg Payload: 83,080 kg Gross vehicle weight: 119,680 kg Financial Information Price: On request Identification Model number: STBZ-5VA + 3 AXLE JEEP DOLLY / E = Company Information = ALL PRICES ARE NET EXPORT, Joris Versteijnen (NL-DE-GB), Wouter Greutink (NL-DE-GB-ES-IT), We speak Russian. We strive to provide accurate information; however, no rights can be derived from the listed texts.

Stanje: novo, največja dovoljena obremenitev: 90.700 kg, skupna masa: 126.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.850 mm, Oprema: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: Hydraulically lift/lower and detachable gooseneck. Length approx. 3,650 mm. Suitable for tractor units: 6x4 or 8x4 3-axle compact front bogie: Pgjdpfx Asw Tgp Dei Rol * Hook mounts at front and rear. Length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Lowbed: * ATX-A lowbed with telescopic longitudinal beams in low-profile design, fixed hardwood floor approx. 50 mm thick * With drive-over bridge hooks at the front and bolt-lug coupling at the rear * Base width: approx. 2,850 mm, length: approx. 7,150 mm, beam height: approx. 330 mm, beam width: approx. 750 mm * Loading height approx. 480 mm, ground clearance approx. 150 mm 5-axle rear bogie: * Mechanical bolt-lug coupling for attaching a lowbed at the front; rear end traverse * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * Pendulum axle 3-axle front bogie: * PENDULUM AXLES, all axles hydro-mechanically forced-steered * Hose rupture valve on axle leveling cylinder with automatic RESET function * Hydraulic cylinders with shutoff taps and locking pins for securing in raised position * Final painting of axles with 2 coats of single color 2K paint, painted in MB7350 Novagrau * Rated axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tires for front bogie: 12 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J 5-axle rear bogie: * PENDULUM AXLES, all axles hydro-mechanically forced-steered * Hose rupture valve on axle leveling cylinder with automatic RESET function * Hydraulic cylinders with shutoff taps and locking pins for securing in raised position * Final painting of axles with 2 coats of single color 2K paint, painted in MB7350 Novagrau * Rated axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tires for rear bogie: 20 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimum corrosion protection * Final painting with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, according to RAL-System 841GL Including accessories: * Steel front wall, approx. 400 mm high * Plug-in aluminum side and rear boards on gooseneck, approx. 400 mm high, anodized * 3.5" kingpin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections on gooseneck * Front bogie with separate air connection for air impact wrench * BEKA-MAX central lubrication for one 3-axle bogie * Preparation for bolt-on container positioning for 1 x 20' or 1 x 30' on the outer beams * Without container locks * Brackets on the outer beams for installing foldable extensions * One 7-pin socket left and right, front and rear on rear bogie for warning panels * BEKA-MAX central lubrication for one 5-axle bogie * On the rear bogie, socket for cable remote control for steering * Rear bogie with trough * 2 LED reversing lights mounted on rear panel * European reflector boards (red-yellow) on the rear * One mudflap at rear * One LED beacon with bracket left and right on rear cross-member * Two INOX toolboxes 855 x 340 x 390 mm on gooseneck, left and right * 1-circuit...

Stanje: rabljeno, lastna masa: 15.550 kg, največja dovoljena obremenitev: 47.450 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2024, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, Leto izdelave: 2024, Oprema: ABS, For every used semi-trailer, you will receive a current and comprehensive inspection and functional report. Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,700 mm long - Gooseneck rear with chamfer, approx. 1,000 mm x 10° Podeypb Akopfx Ai Rjgl Loading platform: - Extendable loading platform, approx. 8,800 mm long, with chamfer at the rear approx. 500 mm x 10° - A recess in the loading platform and into the chamfer to accommodate the excavator's dipper stick - Pneumatic locking with conical locking bolts and reinforced locking positions - Hardwood surface on the chamfer of the loading platform Ramps: - 1 pair of two-part steel ramps, approx. 4,350 mm long and 900 mm wide - Ramps with hardwood inlay - Hydraulically foldable ramp tips - Ramps can be hydraulically shifted approx. 235 mm outwards and 215 mm inwards individually - Square climbing strips 20 x 30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, 1st axle with forced steering, all other axles hydro-mechanically forced steered - Technical axle load: 12,000 kg - Air suspension - Tyres 235/75 R 17.5 - TPMS tyre monitoring system - TPMS tyre pressure sensors Included Accessories: - Plug-in steel front wall, approx. 400 mm high - 3kW electro-hydraulic unit for hydraulic operations - 1 spare wheel - Outer beams on the gooseneck with fixing holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings at the rear of the gooseneck - On the gooseneck: 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized - On the gooseneck: 1 plug-in ALU rear board, approx. 400 mm high, anodized - 2" kingpin - Round NATO socket at the front connection bar - 4 wheel chocks - Mechanical landing gear with 2-speed gearbox and crank - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front crossmember - 8 pairs of recessed lashing rings in the outer frame of the loading platform, foldable outwards - Extendable galvanized outriggers, approx. 230 mm per side - Wheel recesses with square climbing strips, 15 x 15 mm, open continuously in front of the axles up to the gooseneck crossmember, approx. 700 x 410 mm - ALU covers for the wheel recesses - Lockable aluminium elements fitted on the extension pipes of the outriggers - Widenable U-profiles for inserting the ALU covers - Wheel recesses with square climbing strips, 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - Lockable aluminium elements fitted on the extension pipes of the outriggers - 1 pair of mechanical rear supports - Remote steering control from both front and rear by cable remote control, with axle single-track alignment control - 1st axle with automatic lift axle function and start assist according to EU Directive 2021/535 - Under the gooseneck and at the rear crossmember left and right: 7-pin sockets with mountings for warning plates - Square climbing strips 20 x 30 mm, spaced approx. every 200 mm on the chamfered part of the loading platform outer frame - Central lubrication system with 1 pump, BEKAMAX - Radio remote control for steering in addition to cable remote - Wabco Smart Board system - 4 warning plates, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: rabljeno, lastna masa: 9.600 kg, največja dovoljena obremenitev: 30.400 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 12/2011, dolžina tovornega prostora: 13.200 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 800 mm, vzmetenje: zrak, velikost pnevmatike: 205/65R17.5, barva: zelen, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Vehicle location: Bovenden, 4 axles, SAF axles, air suspension, lifting and lowering function, 3rd and 4th axles steered, ABS (anti-lock braking system), extendable, lashing rings, attachable loading ramps, front support, rear support, side aluminium underrun protection, storage box. Body: 4-axle low-bed semi-trailer with attachable loading ramps, SAF axles, 3rd and 4th axles steered, 13 pairs of lashing rings, 10 pairs provisions for insertable stanchions, 13,200 mm loading length fully retracted, 16,800 mm loading length fully extended, 800 mm load height in the low-bed area, low-bed length retracted approx. 9,500 mm, TÜV inspection due, aluminium ramps available at an extra charge of EUR 1,500. ACCESSORY INFORMATION WITHOUT WARRANTY, subject to change, prior sale and errors excepted. Pgsdpfx Aioxxkqze Rel

Stanje: novo, lastna masa: 11.000 kg, največja dovoljena obremenitev: 38.500 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm hardwood flooring Load Area: - Extendable loading area with rear taper approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses fitted with square climbing strips 15 x 15 mm, including lower extensions Pedjup U Hzspfx Ai Regl - Between the 1st and 2nd axle, a pair of fixed wheel recesses with cover, approx. 1,610 x 970 x 400 mm - Recess in the bevel as well as protruding into the loading area for parking excavator dipper stick approx. 2,900 x 750 x 210/290 mm - 1 pair of lashing rings, installed flat at the front of the load area (LC 10,000 daN) - 5 pairs of folding lashing rings on the outside (LC 5,000 daN) - 2 pairs of folding lashing rings on the outside (LC 10,000 daN) - 2 pairs of lashing rings in the dipper stick recess (LC 5,000 daN) - Cut-outs in the outer frame of the load area for securing straps (LC 2,000 daN) - Incl. three-part removable galvanized covers over the wheel recesses – max. point load 3.5 t / pc. Two-piece Steel Ramps: - One pair of galvanized, two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood surfacing - Ramp with hydraulically folding ramp sections, hydraulic lifting gear, and hydraulically adjustable Axles and Tyres: - BPW axles and suspension, 2 rigid axles, 1 steering trailing axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lifting and lowering valve - Axle tool kit - Tyres 235/75 R 17.5 - TPMS tyre pressure monitoring system in accordance with ECE R 141 Accessories Included: - Mounts for warning signs left and right at the gooseneck and at the rear, each with socket - One spare wheel - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings at the galvanized front connector strip - 4 wheel chocks - Galvanized, extendable outriggers approx. 230 mm per side - Galvanized folding supports beneath the loading area bevel - Rear trailer bracket for rotating beacon - Cover plates for bridging the gap between ramps and load area - White reflective tape to EU regulations, sides and on extensions; rear in red - Electro-hydraulic unit installed at the rear beneath the loading area - Ramp control valves mounted on right trailer side - European reflective panels (red-yellow) on rear of trailer - Four extendable warning boards, approx. 423 x 423 mm, with position light - Bracket for rotating beacon on warning boards - Removable ALU side boards and rear board on gooseneck approx. 2,440 x 400 mm - Rear galvanized removable stakes (structure length approx. 2,560 mm) - 2 pairs of WADER container pockets in loading area for 20ft or 30ft container - 3 pairs of socket pockets for stakes 100 x 50 mm in outer frame of loading area - Removable, galvanized intermediate table with 1 pair of WADER container pockets - Square climbing strips 20 x 20 mm spaced every 200 mm on outer frame at loading bevelling - Painted sand layer on chequer plates of the gooseneck and loading area for anti-slip protection - 80 km/h speed stickers rear and both sides - Load manometer for axle load measurement, including load chart.

Stanje: novo, lastna masa: 10.700 kg, največja dovoljena obremenitev: 38.800 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17,5, barva: sivo-črna, Oprema: ABS, Gooseneck: • Gooseneck with front corners beveled at 45° and rear taper approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Extendable loading platform: • Loading platform in extendable design with rear taper approx. 1,000 mm x 8° • Cut-outs in outer frame of loading platform for attaching tensioning straps • Approx. 48 mm thick hardwood flooring; anti-slip checker plate covering above the axles Pjdpfohlz S Nsx Ai Rsgl Two-piece steel ramps: • One pair of galvanized, two-piece steel ramps with approx. 48 mm thick hardwood covering • Ramps with hydraulically foldable ramp sections, hydraulic lift system, and hydraulically adjustable • Maximum load per pair: approx. 40,000 kg Axles and tires: • BPW axles and suspension, 2 rigid axles, 1 self-steering axle • Technical axle load: 12,000 kg • Electromagnetic reverse lock, activated via reverse gear or manually • Air suspension with lift and lower valve • Axle tools • 235/75 R 17.5 3PMSF Braking system: • WABCO braking system according to EU regulations with EBS-E Paintwork: • First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component zinc dust primer • High-quality, single-color top coat in MB 7350 Novagrey applied with two-component paint • Rear section metallized and painted in RAL 9010 Landing legs: • JOST landing legs with 2-speed gearbox for 24t lifting load (50t test load) Steel construction: • Steel construction made of high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC • S690QL/S700MC Electrical system: • Electrical system in accordance with EU regulations, 24 Volt lighting • ASPÖCK-UNIBOX on front connection panel with 24N, 24S & 15-pin sockets Accessories included: • One spare wheel with holder • Galvanized steel front wall approx. 400 mm high • Yellow-red air couplings on the galvanized front connection panel • 4 wheel chocks • Rear mounting bracket for beacon light at the end of the semitrailer • Recess at rear of gooseneck for ALU approach ramps • Galvanized folding supports under the loading platform taper • Cover plates to bridge the gap between ramps and loading platform • White reflector tape per EU regulations on sides, extension, and red at rear • Electro-hydraulic unit at rear, under the loading platform • On gooseneck and ramps, left and right, each with a holder for warning signs, including socket • Operating valves for the ramps located on the right side of the trailer • ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) • Four warning panels extendable by approx. 400 mm with a position light • 3 pairs of WADER container pockets in the loading platform for one 20ft, 30ft or 40ft container • 6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading platform • Galvanized extensions, extendable by approx. 230 mm per side • 20 x 20 mm square climbing strips every 200 mm on the outer frame of the platform taper • Painted anti-slip sand layer on checker plates, above king pin and loading platform • Load gauge for axle load measurement, including load diagram • HRM metallization (High Resistance Metallisation) of the outer frame • Complete steel construction shot-blasted, then defined visible surfaces metallized and hot-finished with ZINACOR 850 (Zinc 85% - Alu 15%)

Stanje: novo, lastna masa: 15.550 kg, največja dovoljena obremenitev: 47.450 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimization of loading platform length, length approx. 3,700 mm Pgsdpfx Aiok Aht Uj Rol - Rear gooseneck with bevel approx. 1,000 mm x 10° Loading Platform: - Extendable loading platform, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° - A recess in the loading platform as well as into the bevel for accommodating the excavator dipper stick - Pneumatic locking with conical locking bolts and reinforced lock positions - Hardwood covering on the loading platform bevel Ramps: - 1 pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm - Ramps with hardwood covering - Hydraulically folding ramp tips - Ramps can be hydraulically shifted individually approx. 235 mm outward and approx. 215 mm inward - Square climbing cleats 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, 1st axle lift-steered, all other axles forced-steered with hydromechanical system - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with raising and lowering valve - Tyres 235/75 R 17.5, twin tires - TPMS tire monitoring system compliant with ECE R141 - TPMS sensors installed in all wheels including spares Accessories included: - Removable steel front wall, approx. 400 mm high - 3kW electro-hydraulic power pack for hydraulic operations, excluding hydraulic winches - Parking position on gooseneck for warning boards when not in use - 1 spare wheel - On the gooseneck: 1 pair of removable side aluminium drop sides, approx. 400 mm high, anodised - On the gooseneck: 1 removable rear aluminium drop side, approx. 400 mm high, anodised - Above the gooseneck: approx. 40 mm thick hardwood floor, chequer plate above king pin - 2" king pin - Guide plate on gooseneck for fifth wheel, approx. 500 mm wide - 4 wheel chocks - Mechanical landing gear with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - 1 intermediate table, approx. 300 mm wide - Extensions (galvanised) extendable by approx. 230 mm per side - Wheel recesses with square climbing cleats - ALU covers for the wheel recesses - 1 pair of mechanical rear supports - Remote steering at front and rear via cable remote control, with single track monitoring of axles - 1st axle with automatic lift axle function - Central lubrication system with 1 BEKAMAX brand pump - Radio remote control for remote steering, additionally to cable remote, with 2 indicator lights on the receiver as single track monitoring - Wabco Smart Board System - 4 warning boards, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for revolving beacon

Stanje: novo, lastna masa: 10.300 kg, največja dovoljena obremenitev: 39.200 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Platform: - Loading platform after the gooseneck, hydraulically liftable and lowerable, length approx. 2,800 mm, with rear chamfer approx. 1,000 mm x 8° - Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, over the axles with chequer plate covering Two-part Steel Ramps: - One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp parts, hydraulic lifting system, and hydraulically adjustable - Maximum load per pair: 40,000 kg Axles, Suspension and Tires: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated by reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tires 235/75 R 17.5 3PMSF - TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories Included: - One spare wheel with holder in front of the bulkhead - 2" kingpin - One galvanized steel front wall approx. 400 mm high - Yellow-red air couplings at the galvanized connection strip in front - 4 wheel chocks - Galvanized folding supports under the platform's rear chamfer - A holder for a rotating beacon at the rear of the trailer - Cover plates to bridge the gap between ramps and platform - White reflective tape as per EU regulations along the sides of the trailer and red at the rear - Electro-hydraulic unit at the rear, under the platform - At the gooseneck and at the ramps left and right, each with a holder for warning signs, including socket - Control valves for the ramps positioned on the right side of the trailer - European reflective plates (red-yellow) at the rear of the trailer - Manual and description on USB stick - Removable ALU side walls and rear wall on the gooseneck approx. 2,440 x 400 mm - The rear, galvanized side stakes are removable (body length approx. 2,560 mm) - An electric cable winch with radio remote control, approx. 5,400 kg lifting force, including 9.5 mm steel cable, 24 m long, with guide roller - Bolted 5 t ring for cable deflection of the winch on the gooseneck without pulley - 2 pairs WADER container pockets in the platform for a 20ft container - 6 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the platform - Lift axle on the front axle with control via TEBS E, depending on actual axle load and loading condition - 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN) - 1 pair of recessed lashing rings along the central beam at the rear chamfer (LC 10,000 daN) - Sand coating for slip resistance painted on the chequer plates on the gooseneck and on the platform - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and removable pump protection - Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm - Speed stickers 80 km/h rear and on both sides - Load manometer for determining axle loads including load chart Pjdsu Hp Hrspfx Ai Rogl - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then all defined visible surfaces metallized and hot-coated with ZINACOR 850 (zinc 85% - alu 15%)

Stanje: novo, lastna masa: 10.900 kg, največja dovoljena obremenitev: 37.100 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 890 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, obratovalna teža: 10.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the loading platform length, approx. 3,700 mm long, rear bevel approx. 1,000 mm x 6° - Technical king pin load: 18,000 kg - For tractor units: 4 x 2 and 6 x 2 Loading platform: - Loading platform, approx. 9,600 mm long with rear taper approx. 900 mm x 6° - Platform area behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, with a load capacity of up to approx. 9,000 kg - Grating surface and steel sheet floor approx. 5 mm thick as additional reinforcement on the sloped section of the platform Pjdpjuadk Njfx Ai Rsgl Ramps: - One pair of two-section AXS steel ramps, approx. 4,675 mm long and approx. 900 mm wide - Grating surface - Hydraulically folding ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 365 mm inward - Painted sand coating on the outer frame and ramp tips - Flashing lights on the outer sides of the ramp tips with control switch next to the ramp operation panel - Ramp lock in transport position with quick-release fastener Axles, suspension and tires: - BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steerable (trailing) - 1st axle with traction assistance - Operated via brake pedal in the tractor unit - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 - TPMS tire pressure sensors installed on all wheels including spare wheels Brake system: - WABCO EBS-E braking system in accordance with EU regulations Paintwork: - Trailer MB 7350 Novagrau Equipment included: - Removable front steel wall, approx. 400 mm high - 3 kW electro-hydraulic power unit for hydraulic operations, except for hydraulic winches - Gooseneck guide plate for the fifth wheel, approx. 500 mm wide - JOST Module B – static test load = 50,000 kg - Continuous grating with 5 mm steel underlay as additional reinforcement - Painted sand coating - Cutouts in the outer frame of loading platform and lift bed for hooking hydraulic ramp control valves on the right-hand side of the vehicle - 2" king pin - Central lubrication system with 1 pump, brand BEKAMAX - 1 pair of plug-in ALU side boards on the gooseneck, approx. 400 mm high, anodised - Electric winch, approx. 5,400 kg pulling force, with radio remote control - Steel wire rope approx. 24 m long, rope diameter approx. 9.5 mm, including rope pressure roller - WABCO Smart Board system - 4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, lastna masa: 10.350 kg, največja dovoljena obremenitev: 39.150 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Loading area: - Telescopic loading area with rear chamfer approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm - Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom - Between the 1st and 2nd axle, 1 pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm - 3-piece detachable galvanized covers over the wheel recesses (W 670 mm) – max. point load 5 t / pc. - Recess in the chamfer and protruding into the loading area for the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of foldable external lashing rings (LC 5,000 daN) - 2 pairs of foldable external lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) - Cutouts in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) One-piece aluminum ramps: - 1 pair one-piece ALU ramps, approx. 2,500 x 600 mm - Ramp with spring lifting mechanism and manually adjustable - Maximum load per pair: 24,000 kg Axles and tires: - BPW axles and suspension, 2 rigid axles, 1 trailing steering axle - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tyres 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 Accessories included: - 1 spare wheel with holder in front of the bulkhead - 2" kingpin - 1 galvanized steel front wall approx. 400 mm high - At the galvanized coupling rail at the front, yellow-red air couplings - 4 wheel chocks with holder at the bulkhead - Mounting point at the rear of the gooseneck for ALU ramps - Galvanized extensions, extendable by approx. 230 mm per side - Galvanized folding supports under the chamfer of the loading area - 1 holder for a rotating beacon at the rear of the trailer - White reflective tape laterally, at the extension, and red at the rear, per EU regulations - At the gooseneck and rear panel, left and right, each with a holder for warning signs including socket - On the gooseneck, plug-in ALU sideboards and rear wall, approx. 2,440 x 400 mm - The rear galvanized stakes are removable (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container - 3 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area - 1 removable galvanized intermediate table with 1 pair of WADER container pockets - 20 x 20 mm square climbing strips every 200 mm on the outer frame in the chamfer of the loading area - Anti-slip sand coating on the checker plates on the gooseneck and the loading area - Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with position light - Holder for rotating beacon on the warning signs Pgodpsiu Er Aefx Ai Rol - 80 km/h speed stickers at the rear and on both sides - Load gauge for determining axle loads including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then all defined visible surfaces metalized and hot-finished with ZINACOR 850 (Zinc 85% – Alu 15%)

Stanje: novo, lastna masa: 34.500 kg, največja dovoljena obremenitev: 106.700 kg, skupna masa: 141.200 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.150 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 580 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, obratovalna teža: 34.500 kg, Oprema: ABS, Gooseneck: - Gooseneck hydraulically lift/lowerable as well as detachable - Length approx. 3,650 mm - Extensive lashing positions - For tractor units: 6 x 4 or 8 x 4 Pgodpfx Aewhywfoi Rel 3-Axle Compact Front Bogie: - Hook mounts at front and rear - Chassis length x chassis width approx. 3,560 mm x 2,850 mm - Extensive lashing positions Excavator Deck “BB-A”: - Telescopic excavator deck “BB-A” with drive-over deck hooks at the front and bolted lug coupling at the rear - Length x base width approx. 7,150 mm x 2,850 mm - Beam height x beam width approx. 430 mm x 1,350 mm - Loading height 580 mm with 150 mm ground clearance - 5 pairs of hanging lashing rings (LC 10,600 daN) - 4 pairs of threaded blocks M30 on inner beam for mounting screw-on rings 5-Axle Rear Bogie: - Mechanical bolt-on lug coupling for fitting a lowbed front, rear end traverse - Chassis length x chassis width approx. 6,840 mm x 2,850 mm - Extensive lashing positions Pendulum Axle and Tyres (front and rear bogie): - “PENDEL-AXLE”, all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-plugs for securing in lifted position - Final paint of axles with 2 coats of 2K paint, single-colour in MB 7350 Novagrau - Technical axle load: 14,640 kg (62 km/h) - Hydraulic axle compensation - Axle tools - Tyres 285/70 R19.5 Steering Override: - Remote steering from the front and rear via cable remote control with push buttons, including axle tracking control - Socket for steering control operation on the gooseneck - Cable remote control with push buttons including axle tracking control Included accessories: - Yellow-red air couplings on galvanised front connection rail - Steel headboard approx. 400 mm high - 4 wheel chocks with holders - 2 spare wheels 285/70 R19.5 - 3.5" kingpin - Gantry with winch for spare wheel at the front side of the gooseneck - Truck hydraulic connection with flow control valve (40 l/min), including gantry for suspension of supply lines, tractor unit tank must be at least 80 litres with couplings - White reflective tape according to EU regulations on sides and extension, red at rear - Plug-in ALU side panels and rear wall on gooseneck, approx. 400 mm high, anodised - Operating lever on gooseneck protected by folding cover - Separate air connection with air pistol on gooseneck - Central lubrication system BEKAMAX with standard grease NLGI-2: 1x on the gooseneck, 1x on 3-axle bogie, 1x on 5-axle bogie - Variomax tool kit - Multi-coupling hydraulic connections in the lowbed hook area - Front bogie with separate air connection for air screwdriver - Threaded inserts (ø 40 mm) every approx. 500 mm on outside of upper flange of excavator deck for screw rings - Folding extensions with steel mats, width adjustable from approx. 2,850 mm to approx. 3,250 mm - Steel mats with rubber covering approx. 12 mm thick - Two INOX toolboxes 855 x 340 x 390 mm - Radio remote control for steering override in addition to cable remote - Painted sand layer as anti-slip measure - 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery

Stanje: novo, lastna masa: 17.250 kg, največja dovoljena obremenitev: 48.700 kg, skupna masa: 66.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 375 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 17.250 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize loading platform length, approximately 3,750 mm long - Gooseneck hydraulically liftable, lowerable, and detachable - For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Lowbed: - Lowbed with external beams, designed as a telescopic vessel bridge in low-profile construction with front extension - Length x width approx. 7,550 mm x 2,740 mm - Mechanical locking of the extension Chassis: - Rear chassis with closed outer frame - Checker plate surface and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, Suspension, and Tyres: - “PENDEL-AXLE”, all axles hydromechanically forced steered - Burst protection valve on the axle compensation cylinders with automatic reset function - Hydraulic cylinders with shut-off valves and plug pins for securing in raised position - Final coating of axles: two coats of single-color 2-component paint in "FAY-Grey-34-0260" - Technical axle load 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 Accessories: - Detachable steel front wall, approx. 400 mm high - 4 wheel chocks - Rear upper gooseneck area closed with removable cover - 1 pair of steel ramps with climbing bars and locking bolts to bridge the lowbed mounting hooks - Ramps can be positioned over or between the hooks - Mounting options for steel drive-on ramps at the rear, between the outer beams of the gooseneck - Locking point approx. every 1,000 mm on the extension - 1 lashing ring each, left and right, on the front cross member - Supply line connection strip for tractor unit, mounted at the height of outer frame profile - 6 pairs of threaded blocks on the exterior of the load floor inner beams for attaching M24 screw rings - 6 pairs of recessed lashing rings on the outside of the load floor outer beams, foldable inwards and outwards - 1 pair of threaded blocks on the front and rear of the load floor outer beams for M24 screw rings - Mounting rail for loose aluminum approach ramps on the end cross member of the vehicle - Central lubrication system with 2 pumps, brand BEKAMAX - Remote steering front and rear, cable remote controlled, with axle tracking control - 3 kW electro-hydraulic power unit for hydraulic operations, except hydraulic winches - Removable galvanized loading floor, can be placed in 3 elements between the outer beams, with hardwood covering - Foldable extensions, approx. 230 mm per side - Loose extension boards, steel-edged - 4 warning signs approx. 423 x 423 mm - Radio remote control for rear steering - 3.5” kingpin - Anti-slip coating on the left chamfer of the gooseneck - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Guide plate from gooseneck for the fifth wheel plate, approx. 800 mm wide Pedpeh Hm Tzjfx Ai Rjgl - 1 spare wheel with mounting adapter - Parking position on the gooseneck for warning signs when not in use - 2 pairs of stake pockets integrated into the chassis outer frame, for plug-in stakes approx. 100 x 50 mm - Excavator stick trough of rear chassis closed at the rear with a removable plate - Trailer color: Mercedes-Benz 7350 Novagrey

Stanje: novo, lastna masa: 17.500 kg, največja dovoljena obremenitev: 43.500 kg, skupna masa: 61.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.750 mm, višina nakladalnega prostora: 400 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - For tractor units: 6x4 or 8x4 Lowbed: - Lowbed with external beams, extendable version, "SUPER LOW" design, approx. 7,550 mm long - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking device Pgjdpfxsh Hm The Ai Rjl - Service lines are protected within the extendable beams and automatically adjust to the lowbed length Rear Undercarriage: - Rear chassis with closed outer frame, checker plate cover, and continuous prism-shaped excavator trough approx. 1,450/900 x 505 mm, open at the rear - 2 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame Axles and Tires: - "PENDULUM AXLE", all axles hydro-mechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 / 3PMSF Included Accessories: - Prepared for bolt-on container positioning for 1x 20ft or 1x 40ft container on the outer beams - 2" kingpin - Galvanized steel front wall approx. 400 mm high - One spare wheel with holder - At the galvanized front adapter bar yellow-red air couplings - 4 wheel chocks - Remote rear steering from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Hydraulic line connections from gooseneck to lowbed with multi-coupling instead of screw coupling - Electro-hydraulic power pack - White reflective tape to EU specifications on sides, extension, and rear red - 2 wooden blocks 500x250x200 mm - European reflective plates (red-yellow) on the trailer rear - At the gooseneck and rear wall left and right each a bracket for warning boards including socket - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 - Load gauge for determination of axle loads including load diagram - On the gooseneck, plug-in ALU side and rear boards approx. 2,000 x 400 mm - The rear galvanized insert posts are removable (body length approx. 2,120 mm) - Separate air connection for air gun on the gooseneck - Duomatic air coupling from gooseneck to lowbed - Rear upper section of gooseneck closed with removable cover - 1 pair of steel ramps to bridge the lowbed's pick-up hooks - Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm - Wireless remote control for rear steering in addition to cable remote, with signal lights at receiver for single-track monitoring - 6 pairs of threaded blocks between lashing rings under the top chord on the outer beams for mounting screwable RUD rings VLBG-4 - 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading bed - Foldable extensions, approx. 230 mm per side - Loading area features a painted sand layer for anti-slip protection - Dipper stick trough of rear chassis closed at front and rear with plug-in plates - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - alu 15%)

Stanje: novo, lastna masa: 9.500 kg, največja dovoljena obremenitev: 35.500 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.500 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 435/50 R 19.5, barva: siv, obratovalna teža: 9.500 kg, Oprema: ABS, Loading platform in extendable design: Loading platform with hardwood planks, rear bevel approx. 1,000 mm x 8° 1 pair of fixed integrated wheel recesses, approx. 1,610 x 970 x 400 mm 2 pairs of lashing rings (LC 5,000 daN) 1 pair of lashing rings (LC 10,000 daN) 6 pairs of fold-out lashing rings on the outside (LC 5,000 daN) 2 pairs of fold-out lashing rings on the outside (LC 10,000 daN) Cut-outs in the outer frame of the loading area for attaching tensioning straps (LC 2,000 daN) Brake system: Brake system as per EU regulations with EBS-E (2S2M) Paintwork: Premium, long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc-rich primer High-quality single-colour 2-component (2K) top coat in Nova grey Rear section metallized and painted in RAL 9010 (Pure White) No metallic paint possible Landing gear: JOST mechanical landing gear with 2-speed gearbox for 24t lifting capacity (50t test load) Steel construction: Steel construction from high-tensile fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical system: Electrical system according to EU regulations, 24 volt lighting Sockets: 24N, 24S & 15-pin Axles and tyres: BPW axles, air suspension, with disc brakes (377 mm), with lift/lower function Trailing steering axles with electro-magnetic reversing lock, actuated via reverse gear or manually Axle tool Tyres: 435/50 R 19.5 Accessories included: At the galvanized front connection strip: yellow-red air couplings 4 wheel chocks with brackets 2" kingpin Galvanized steel front wall approx. 1,600 mm high, EN12642-XL White reflective tape to EU standards on the sides, extension section and red at the rear Loading platform with heavy-duty hardwood floor 9 pairs of stake pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform 1 spare wheel holder under the platform on the right (direction of travel) Galvanized folding supports under the rear slope of the loading area Sliding mounting rails for ALU loading ramps at the rear of the vehicle European reflective plates (red-yellow) at the rear of the semi-trailer One mudflap at the rear of the semi-trailer Pgedpfx Aijk Eammj Rol Bracket for a rotating beacon at the rear of the semi-trailer At the gooseneck and on the rear panel left and right, each with a bracket for warning panels including socket One HDPE toolbox 620x360x610 under the platform on the left (direction of travel) 4 pairs of WADER container locks in the platform for 1x 20ft container or 1x 40ft container; additional locking position in the extension for a 45ft container 3 pairs of transverse stake pocket rails on the platform for 100 x 50 mm plug-in stanchions Lift axle on the front axle with control via TEBS E, depending on current axle load and loading condition Speed stickers 80 km/h on the rear and both sides Four warning boards extendable by approx. 400 mm, approx. 423 x 423 mm, with LED position light. Mounting for rotating beacon on warning boards Load gauge including axle load diagram HRM metallization (High Resistance Metallisation) of the outer frame Complete steel structure shot blasted, then specified visible surfaces metallized

Stanje: novo, lastna masa: 10.600 kg, največja dovoljena obremenitev: 35.400 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.500 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 940 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Loading area: - Loading deck in extendable design - Loading deck with hardwood planks, rear bevel approx. 500 mm x 8° - 2 pairs of lashing rings (LC 5,000 daN) - 1 pair of lashing rings (LC 10,000 daN) - 6 pairs of outward-folding lashing rings (LC 5,000 daN) - 3 pairs of outward-folding lashing rings (LC 10,000 daN) - Cut-outs in the loading deck's external frame for attaching tension belts Braking system: - Braking system in accordance with EU regulations, with EBS-E (2S2M) Painting: - First-class, durable corrosion protection for the standard shot-blasted welded frame guaranteed by a two-component (2K) zinc-rich primer - High-quality two-component (2K) top coat in solid Novagrey - Rear section metallised and painted in RAL 9010 (pure white) - Metallic paint not available Landing gear: - JOST mechanical landing gear with 2-speed gearbox, 24t lifting capacity (test load 50t) Steel construction: - Steel structure made from high-strength fine grain steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system according to EU regulations, LED lighting 24 Volt - Sockets: 2x 7-pin & 15-pin Axles and tyres: - BPW axles, air suspended, with disc brakes (377 mm), with lifting/lowering function - Hydro-mechanically forced steering Pgjdpfol Ux Rwsx Ai Rjl - Axle tools - Twin tyres 235/75 R 17.5 Accessories included: - Yellow-red air couplings at the galvanised front connection bar - 4 wheel chocks with holder - 2" king pin - Galvanised steel headboard approx. 1600 mm high - White reflective tape on the sides, sliding section and rear in red in accordance with EU regulations - Loading deck with heavy-duty hardwood floor - Rear and front steering by cable - Remote control via push buttons, with single-track monitoring of the axles - With wireless remote control for rear steering - 9 pairs of stake pockets for 100 x 50 mm plug-in stakes on the outer frame of the loading deck - Galvanised folding supports under the loading deck bevel - Sliding mounting rail for aluminium loading ramps at the rear of the vehicle - European reflective panels (red-yellow) at the trailer rear - One mud flap at the trailer rear - Mount for a beacon at the trailer rear - Mounts for warning boards including socket on gooseneck and rear panel, each left and right - Stainless steel toolbox INOX 1,500 x 390 x 810 under the loading deck, right side in driving direction - Central lubrication system BEKAMAX (Pico) with NLHI-2 multipurpose grease and removable protection around pump - 6 pairs of WADER container locks on the loading deck for 1x 20ft, 2x 20ft or 1x 40ft containers, additional locking for one 45ft container in extendable section - 4 pairs of crosswise stake pocket strips mounted in the loading area for 100 x 50 mm plug-in stakes - Lift axle on the first axle, controlled by TEBS, dependent on current axle load and load condition - 80 km/h speed stickers at the rear and on both sides - Four extendable warning boards ca. 400 mm (approx. 423 x 423 mm) with LED position light - Beacon mount on the warning boards - Load gauge for axle load determination, including load diagram - HRM metallisation (High Resistance Metallisation) on the external frame - Complete steel construction shot-blasted, then all defined visible areas metallised with ZINACOR 850 (85% zinc, 15% aluminium) by thermal spraying

Stanje: novo, lastna masa: 11.300 kg, največja dovoljena obremenitev: 36.700 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.250 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 r 22,5, barva: sivo-črna, Oprema: ABS, Loading platform: Loading platform in extendable design with pneumatically operated locking mechanism A fixed intermediate table, approx. 250 mm wide, is mounted on the central beam 8 pairs of lashing rings, foldable outwards (LC 5,000 daN) 3 pairs of lashing rings, foldable outwards (LC 10,000 daN) Openings in the outer frame of the loading platform for attaching tensioning straps (LC 2,000 daN) Axles and tyres: BPW axles and suspension, all axles with hydro-mechanical forced steering Disc brakes, technical axle load: 10,000 kg Air suspension with lift and lower valve Axle tools 6 tyres, size 385/65 R 22.5 Brake system: Brake system according to EU regulations with EBS-E (2S2M) Landing gear: JOST landing legs (mechanically operated) with 2-speed gearbox for 24 t lift load (50 t test load) Steel construction: Steel construction made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical system: Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX mounted on the front terminal board with 24N, 24S & 15-pin sockets Connections according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Pgsdpfx Aishlz Sho Rjl Paintwork: First-class, long-lasting corrosion protection of the standard grit-blasted welded frame, guaranteed by a 2-component (2K) zinc-dust primer High-quality, single-colour 2-component (2K) top coat in Novagrau Rear section metallised and painted in RAL 9010 (pure white) No metallic paint finish possible Included accessories: At the gooseneck and at the rear plate, left and right, each with a bracket for warning signs, including socket Remote steering from the front and rear via cable remote control with push buttons, with single-track control of the axles Electro-hydraulic unit 4 wheel chocks with brackets on the front wall 2" kingpin A galvanised steel front wall approx. 2,200 mm high Yellow-red air couplings on the galvanised front terminal board White reflective tape on the side, at the extension and rear in accordance with EU regulations, red at the rear European reflective plates (red-yellow) on the rear of the trailer One mud flap on the rear of the trailer Manual and documentation Bracket for a revolving warning light at the rear of the trailer Loading platform with approx. 30 mm thick wooden floor set in omega profiles 10 pairs of stake pockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading platform 1 spare wheel holder under the loading platform on the right-hand side in the driving direction 6 pairs of WADER container locks in the loading platform, for 1x 20ft container, 2x 20ft containers or 1x 40ft container; in the extension, an additional locking position is provided for a 45ft container 5 pairs of stake pocket strips, mounted transversely in the loading platform, for plug-in stanchions 100 x 50 mm A galvanised bracket mounted transversely under the loading platform (2,390 x 720 x 400 mm) Access ladder mounted on the right in the direction of travel One HDPE toolbox 1,200x500x480 mounted at the front under the loading platform on the left in the direction of travel Lift axle on the front axle with control via TEBS E depending on the current axle load and loading status Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable protection around the pump Red/white reflective tape on the extension of the loading platform On the central beam,

Stanje: novo, največja dovoljena obremenitev: 48.300 kg, skupna masa: 71.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete vehicle inventory, including vehicles available immediately and at short notice, can be found on our website. Below is an excerpt from the equipment list. Full specification available upon request. GOOSENECK: * Gooseneck with integrated single-axle running gear (pendulum axle) in a detachable version * Gooseneck hydraulically liftable and lowerable, including hydraulic connection linked to the hydraulic axle compensation of the first axles * Length: approx. 5,200 mm, with front tapering approx. 60° * Fifth wheel load according to data sheet: W25-DSR2700-12/22.7 * For tractor units: 6 x 4 or 8 x 4 * Steel front wall, plug-in type, approx. 400 mm high, with beveled design * 1 pair of mechanical supports at the front of the gooseneck * ASPÖCK-UNIBOX on the front connector panel with 24N, 24S & 15-pin sockets * 1 spare wheel holder inside the front wall of the gooseneck with jib * 2 pairs of recessed lashing rings on the gooseneck (LC 2,500 daN) * 2 pairs of recessed lashing rings on the outer frame of the running gear at the front, foldable outward (LC 10,000 daN) * 1 pair of lashing rings at the transition from running gear to loading platform (LC 10,600 daN) * On the gooseneck 1 pair of removable aluminum drop sides, approx. 400 mm high, anodized * On the gooseneck 1 removable aluminum rear wall, approx. 400 mm high, anodized * 3.5 inch kingpin * TPMS tire pressure monitoring system according to ECE R 141 Pedpfx Aieyhkqnj Regl * Round NATO socket on the front connector panel (Maeler & Kaege VG 96 917) * 1 stainless steel toolbox with 1 lid, mounted on the gooseneck on the right in the direction of travel by the aluminum drop side, approx. 1,350 x 400 x 400 mm (L x W x H) LOADING PLATFORM: * Low-bed with external beams, designed as a telescopic loading platform in low-profile design with front extension including fixed approx. 50 mm thick hardwood floor * Length x width approx. 8,000 mm x 2,740 mm * Mechanical bolt-lug coupling from low-bed to running gear for swapping the loading platform or installing extension beams * One locking position approx. every 500 mm on the extension * 4 pairs of recessed lashing rings fitted flat in the loading platform along the outer frame/external beams (LC 10,000 daN) * 1 lashing ring each on the left and right outer rear cross member (LC 10,000 daN) * Foldable extensions, approx. 230 mm per side (WITHOUT wooden boards) * Loose extension planks, steel-rimmed * Preparation for installation of bolted container positions for 1x 20’ or 1x 40’ container on the outer beams. Without container locks * 6 pairs of threaded blocks between the lashing rings under the top chord of the outer beam for mounting bolted M24 rings (LC 8,000 daN) * 2 pairs M24 bolt rings (LC 8,000 daN) included REAR RUNNING GEAR: * Rear running gear with closed outer frame, checker plate decking and continuous prism-shaped excavator trough, approx. 1,450 x 900 x 505 mm, open at the rear * PENDULUM AXLE, all axles hydro-mechanically forced-steered * Hose rupture valve on axle compensation cylinder with automatic reset function * Hydraulic cylinders with shut-off valves and foreplugs to secure in raised position * Final paint of axles in 2 layers of 2-component paint, single color, DB 7350 Novagrau * Technical axle load: 12,000 kg each * Hydraulic axle compensation * 245/70 R 17.5 3PMSF, brand at our choice * Remote steering from front and rear via cable control, with axle alignment check, no installation in the tractor unit * 4 pairs of hanging la

Stanje: novo, lastna masa: 10.000 kg, največja dovoljena obremenitev: 41.600 kg, skupna masa: 51.600 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Loading Platform: - Gooseneck, length approx. 4,100 mm with central beam - Extendable loading platform, length approx. 9,500 mm with rear taper approx. 350 mm x 10° and integrated hook-on bar for attaching loose ALU approach ramps - Pneumatic locking system with conical locking bolts and reinforced locking positions - Supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles, Suspension, and Tyres: - BPW axles and suspension, all axles hydro-mechanically forced steered - Mounted on turntable - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - Tyres 235/75 R17.5, twin-mounted Paintwork: - 6-coat surface treatment - Complete steel structure shot-blasted after welding - One coat of zinc-based primer, one coat of adhesion primer - Final paintwork with 2 layers of 2-component (acrylic) paint, single colour in MB 7350 Novagrau, followed by cavity sealing with special wax Steel Structure: - Steel structure made from high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355MPa) - S690QL/S700MC (yield strength 690MPa) - Welders certified according to DIN-EN 287-1 - Welding process MAG according to EN ISO 4063, shielding gas M21 according to EN ISO 14175 Accessories: - Steel front wall, approx. 1,600 mm high - Round NATO socket at the front connection strip - 3 kW electro-hydraulic unit for controlling hydraulic functions - 4 pairs of recessed lashing rings in the outer frame of the gooseneck - 4 pairs of stake pockets integrated into the outer frame of the gooseneck for stakes approx. 100x50 mm - 1 transverse stake pocket strip mounted in the floor of the gooseneck for stakes approx. 100x50 mm (1x rear on gooseneck) - 2'' kingpin - Mechanical landing legs with 2-speed gearbox and hand crank - JOST Module B – static test load = 50,000 kg Pjdsiuy Nlspfx Ai Rjgl - On the gooseneck and loading area, approx. 32 mm wooden flooring in ALU-omega profiles - One locking position on the extension, approx. every 500 mm - 10 pairs of recessed folding lashing rings in the outer frame of the loading area, folding outwards - 6 pairs of stake pockets integrated into the outer frame of the loading area for stakes approx. 100x50 mm - 2 transverse stake pocket strips mounted in the floor of the loading area for stakes approx. 100x50 mm - INOX toolbox approx. 1,250 x 500 x 550 mm - Tapered end crossmember of the vehicle, approx. 350 mm 10° - Integrated hook-on bar for loose ALU approach ramps at the rear crossmember of the vehicle - 1 pair of drop tube supports at the rear crossmember - Mudguards on all axles - Central lubrication system with 1 pump - Remote steering from front and rear operable via cable remote control with push button, including single-track monitoring of the axles - Under the gooseneck and at the rear crossmember, left and right, each with a 7-pin socket for warning panels - One 7-pin socket at the rear crossmember - Container locks "TWIST-LOCKS" in the loading area for transport of 2x 20ft and 1x 40ft containers - Radio remote control for rear steering in addition to cable remote control, with 2 indicator lights on the receiver for single-track monitoring - 2 axle load gauges + axle load diagram - 4 warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Standard HRM Metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible areas hot-coated in metallic finish using ZIN

Stanje: novo, lastna masa: 14.350 kg, največja dovoljena obremenitev: 53.450 kg, skupna masa: 67.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, dvižna zadnja plošča, Gooseneck: - Gooseneck in SNT design for optimization of loading bed length, length approx. 3,700 mm - Gooseneck rear with chamfer approx. 1,000 mm x 10° - For tractor units: 6x2, 6x4, 8x4 short Loading bed: - Extendable loading bed, length approx. 8,800 mm, rear chamfer approx. 500 mm x 10° - A recess in the loading bed and the chamfered section for receiving the excavator dipper stick, approx. 3,850 x 750 x 210/290 mm Two-part steel ramps: - One pair of two-part steel ramps, length approx. 4,350 mm, width approx. 900 mm Pgodpfoya E A Nex Ai Rol - Ramps with rubber covering - Ramps hydraulically adjustable individually approx. 235 mm outwards and approx. 215 mm inwards - 'Super Grip' 25 mm rubber flooring and approx. 5 mm steel plate as additional reinforcement on the rear chamfer of the loading bed - Square climbing bars 20 x 30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: - BPW axles and suspension, 1st axle steering, all other axles hydromechanically forced-steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Tires 235/75 R 17.5 - TPMS tire monitoring system according to ECE R141 - TPMS tire sensors fitted on all wheels, including spares Surface treatment: - Complete steel structure automatically blasted with shot blasting system after welding - Second blasting with corundum for optimum coating adhesion - HRM metallization of entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for best corrosion protection - Final painting with 2 layers of 2K top coat, single colour in MB 7350 Novagrau Accessories included: - Plug-in steel front wall, approx. 400 mm high - 3kW electro-hydraulic power unit for controlling hydraulic functions, with the exception of hydraulic winches - 1 spare wheel - Outer carrier on the gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings in the rear area of the gooseneck - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized - On the gooseneck, 1 plug-in ALU rear board, approx. 400 mm high, anodized - On top of the gooseneck, approx. 40 mm thick hardwood flooring, above kingpin area with checker plate cover - 2" kingpin - Round NATO socket on front connection strip - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front cross member - 8 pairs of recessed, fold-out lashing rings in the outer frame of the loading bed - Extendable (galvanized) widenings by approx. 230 mm per side - Wheel recesses with square climbing bars, 15 x 15 mm, in front of the axles fully open up to gooseneck cross beam, approx. 700 x 410 mm - Wheel recesses with square climbing bars, 15 x 15 mm, between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - ALU covers for wheel recesses, which can also be used as bridging elements for the extension or as widening boards - 1 pair mechanical rear supports - Radio and cable remote control - Lift axle on front axle - Square climbing bars 20 x 30 mm, approx. every 200 mm - Central lubrication system with 1 pump - Wabco Smart Board system - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, lastna masa: 9.300 kg, največja dovoljena obremenitev: 38.700 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.200 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R 22,5, barva: sivo-črna, Oprema: ABS, Cargo Area: • Extendable cargo area with pneumatically operated locking mechanism • Cargo platform with approx. 30 mm thick timber flooring • 7 pairs of external folding lashing rings (LC 5,000 daN) • 3 pairs of external folding lashing rings (LC 10,000 daN) • Cutouts in the outer frame of the cargo area for attaching tensioning straps (LC 2,000 daN) Axles and Tyres: • BPW axles and suspension, all axles hydromechanically forced-steered • Equipped with disc brakes • Technical axle load: 10,000 kg • Air suspension with lift and lower valve • Axle tool kit • Tyres: 385/65 R 22.5 • TPMS tire pressure monitoring system compliant with ECE R 141 Brake System: • WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Electrical System: • Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) • ASPÖCK-UNIBOX at the front control strip with 24N, 24S & 15-pin sockets • Connections as per ISO standards • 24N ISO-1185 • 24S ISO-3731 • 15-pin ISO-12098 Standard Accessories Included: • Remote-controlled steering from front and rear via cable remote control with push buttons, including single-track axle monitoring • 4 wheel chocks with holders mounted on the front wall • 2" king pin • One galvanized steel front wall, approx. 1,600 mm high • Yellow-red air couplings at the galvanized front connection strip • White reflective tape compliant with EU standards on both sides, on extension, and at the rear of the trailer in red • European reflective plates (red-yellow) at the rear of the trailer • One mud flap at the rear of the trailer • Operating manual and instructions • Mount for a revolving beacon at the rear of the trailer • Cargo area with approx. 30 mm thick timber floor inset in omega profiles • 10 pairs of stake pockets (100 x 50 mm) in the outer frame of the cargo bed • 1 spare wheel holder under the cargo area, right-hand side in the direction of travel • Electro-hydraulic unit • At the gooseneck and rear panel left/right, each with bracket for warning signs, incl. socket • Coated sand layer on the main beam as anti-slip protection • 6 pairs of WADER container pockets in the cargo area for 1x20ft, 2x20ft or 1x40ft containers; additional locking point provided in the extension for a 45ft container • 4 pairs of transverse stake pocket rails in the cargo area for plug-in stakes 100 x 50 mm • Access ladder mounted on the right side in the direction of travel • One HDPE toolbox approx. 1,200 x 500 x 480 mm at the front under the cargo bed, left in the direction of travel • BEKAMAX (Pico) centralized lubrication system with removable pump guard • Lift axle on front axle, controlled via TEBS E according to dynamic axle load and load status • Wireless remote control for steering, in addition to cable operation, with indicator lights on receiver for single-track monitoring • Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm, equipped with position light • Bracket for revolving beacon on the warning signs • 80 km/h speed sticker on rear and both sides • Load gauge for axle load determination, including load chart Pjdpfx Aieiu Etre Rsgl • HRM (High Resistance Metallisation) of the outer frame • Complete steel construction shot blasted; subsequently, defined visible surfaces metallised by hot-dip application with ZINACOR 850 (85% zinc – 15% aluminium)

Stanje: novo, največja dovoljena obremenitev: 91.640 kg, skupna masa: 126.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.850 mm, Oprema: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. Gooseneck * Gooseneck hydraulically liftable/lowerable and detachable. Length approx. 3,650 mm. For tractor units: 6 x 4 or 8 x 4 3-Axle Compact Front Bogie * Hook connection front and rear, length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Excavator Deck * Telescopic excavator deck BB-A with drive-over deck hooks at the front and pin-lug coupling at the rear * Base width: approx. 2,850 mm, length: approx. 7,150 mm, beam height: approx. 430 mm, beam width: approx. 1,350 mm * Load height approx. 580 mm with ground clearance approx. 150 mm 5-Axle Rear Bogie * Mechanical pin-lug coupling for attaching a lowbed at the front, end traverse at the rear * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * 3-axle pendulum axle Front Bogie * PENDULUM AXLE, all axles hydro-mechanically force-steered * Hose rupture valve on the axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and retaining pins for securing in lifted position * Final coating of axles with 2 coats of 2C paint, solid colour in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tyres front bogie: 12 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J, pendulum axle 5-Axle Rear Bogie * PENDULUM AXLE, all axles hydro-mechanically force-steered * Hose rupture valve on the axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and retaining pins for securing in lifted position * Final coating of axles with 2 coats of 2C paint, solid colour in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tyres rear bogie: 20 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) guaranteeing optimal corrosion protection Pgsdpfx Aisuvbdts Rjl * Final coating with 2 coats of 2K paint, solid colour in RAL 3002 Carmine Red, according to RAL system 841GL. Rims in silver grey Incl. Accessories * Steel front wall, approx. 400 mm high * Detachable ALU sideboards and tailboard, approx. 400 mm high, anodized, for installation on the gooseneck * 3.5" kingpin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections on the gooseneck * BEKA-MAX central lubrication for a 3-axle chassis * One 7-pin socket left and right at the rear of the front bogie for warning plates * Screw-in option (ø approx. 40 mm) every approx. 500 mm on the upper flange of the outer tube of the excavator deck for lashing rings (LC 16,000 daN) * Folding extensions with steel mattress, adjustable in width from approx. 2,850 mm to approx. 3,250 mm * The steel mats can be inserted in 2 positions to create a lowered loading area. Please refer to the respective load diagram for the load capacity, depending on extension width * Steel mats with rubber covering approx. 12 mm thick * One 7-pin socket left and right, front and rear on the rear bogie for warning plates * BEKA-MAX central lubrication for a 5-axle chassis * Rear bogie with socket for cable remote control for steering * Rear bogie with trough * Two INOX toolboxes, approx. 855 x 340 x 390 mm, on the gooseneck, left and right * 1-cylinder