Müller-Mitteltal Eal Prikolice nakup rabljenega (258)

Stanje: novo, največja dovoljena obremenitev: 38.900 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T5 profile 50.0: * Wabco EBS (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Last axle steering (axle lock for manoeuvring can be activated from the cab without additional truck-side installation, and additionally via a switch on the trailer); the lock must be disengaged before driving on public roads * Air suspension, lift and lowering system with RtR valve Kfjdpoxptn Djfx Ab Uja * 3rd axle liftable (ride height +30 mm with lifted axle) * Forced relief and forced lowering of the lift axle for manoeuvring (requires truck-side installation), speed-dependent activation via EBS * Smartboard infotool with pressure sensors for total axle load display per axle group * TPMS with display option in the truck via EBS signal (no truck-side installation required) * Mechanical warning sign kit for 3m total width * Drawbar 1,500 mm long with 50 mm towing eye and manual height adjustment * LED lighting system 12/24 V * Removable rear LED beacon * Toolbox, galvanised steel approx. 650 x 300 x 600 mm, mounted left side * Plastic fenders front axle, galvanised steel mud guards rear axle * Turntable platform extension with 45° corners and 3 storage compartments with lockable folding lids (lids open to rear) * Shortened low-loader deck by 500 mm to 6,280 mm incl. extended step by 500 mm to the front * Load securing package: 2 x 6.4 t lashing rings front corners, side front & rear corners each 2 x 13.4 t UVV lashing rings, 5 x 10 t UVV lashing rings per side (pivoting/lowering and loadable in all directions), 4 stake pockets per side additionally providing 2 t lashing option, 1 x 16 t UVV lashing ring on rear traverse * Rubber matting on folding ramp, approach slope, and low loader running surface * Bamboo wood inserted between main beams in excavator arm storage area * Extendable and folding outrigger extensions for 3 m total width (beam holder under chassis, right side) * Continuous excavator arm storage with reinforcement profile from last axle to rear cross member approx. L=2,350 x W=770 x H=270 mm, 2 pairs 6.4 t UVV lashing rings on sides * Hydraulic folding ramp with dual-line hydraulics and extendable tip section, approx. 4,650 x 720 mm incl. load-holding valves and hydraulic side shift * Hydraulic rear support * Hydraulic flow divider (for truck hydraulic capacity over 40 l/min up to 140 l/min) * Loaded platform height 890 mm +/- 20 mm (via air suspension) * Platform above turntable: 2,600 + 390 x 2,520 mm * Low-bed platform: 6,280 + 500 x 2,520 mm incl. 860 mm approach ramp * Chassis, turntable, drawbar, extension consoles, and access ramps hot-dip galvanised * Drawbar, axles, hydraulic axle supports, and air tanks painted black * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from week 14/2026

Stanje: rabljeno, skupna masa: 32.000 kg, konfiguracija osi: 2 osi, prva registracija: 01/2014, prostornina tovornega prostora: 10 m³, skupna širina: 2.500 mm, skupna višina: 4.000 mm, Oprema: ABS, For inquiries regarding the vehicle, Mr. Seidel will be happy to assist you (by phone at ...). ----MÜLLER MITTELTAL SF32BM/BT Concrete Mixer Semi-Trailer---- * Superstructure: Liebherr HTM 1004 10m³ * BPW axles * Drum brakes * Spring-loaded brakes * Wabco ABS * 1st axle liftable * Air suspension * Permissible total weight: 32,000 kg * Unladen weight: 6,510 kg * Payload: 25,490 kg * Tire tread depth: 1st axle 14-15 mm, 2nd axle 10 mm Upon request, we can provide you with a leasing or financing offer. Mr. Seidel (phone ...) will be happy to assist you. For more information, please visit our homepage. Kedowipfnopfx Ab Uofa !!! Subject to errors, changes, and prior sale !!!

Stanje: rabljeno, največja dovoljena obremenitev: 13.860 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2022, dolžina tovornega prostora: 6.770 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 600 mm, prostornina tovornega prostora: 10 m³, Oprema: ABS, ? pocinkano podvozje ? nizko sklopljen ? vlečno oko 50 mm Kfedpfsxb Ig Sjx Ab Uja ? zaklep za kontejner ? po 12 pritrdilnih obročev na vsaki strani ? vzvratna kamera ? bobnaste zavore ? duomatski priključek ? ABS ? zračno vzmetenje ? orodjarna ? EBS ? podporne noge ? dvojna kolesa ? BPW osi Vse informacije brez garancije / Vmesna prodaja pridržana.

Stanje: rabljeno, lastna masa: 3.450 kg, največja dovoljena obremenitev: 14.550 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 05/2010, naslednji pregled (TÜV): 07/2025, vzmetenje: zrak, velikost pnevmatike: 235/75R17.5, barva: rumena, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Vehicle location: Bovenden, 2 axles, turntable trailer, air suspension, ABS (anti-lock braking system), container locking mechanism, underrun protection, side aluminum side guard, twin tires. Body: 2-axle outer roller trailer for roll-off containers from 5.5 m to 7 m or 2x 10 m³ skip containers, BPW axles, drum brakes, pneumatic locking, pneumatic lowering drawbar. Kfsdpfsxgilmsx Ab Usa ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale, and errors!

Stanje: novo, največja dovoljena obremenitev: 8.750 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Oprema: ABS, dvižna zadnja plošča, Inquiry number: 23185-O * Available immediately New Müller-Mitteltal KA-TA-R 11.9 tandem low-loader, three-way tipper trailer with ramps * Tyres: 385/55 R19.5 (4 pieces), BPW axles, parabolic springs, drum brakes * Gross weight: 11,900 kg, payload: 8,750 kg * Tyre pressure monitoring system with display option in the truck via EBS signal * EBS 24 volt * Side marker lights with integrated indicator function * LED lighting system for 12V and 24V * 2 LED reversing lights at the rear, suitable for 12V and 24V * Galvanized floor, 5m x 2.42m x 0.5m, laser-welded side walls, swinging, foldable, and removable, prepared for later retrofitting of side wall extensions * Stay wires for the tailgate * Lockable compartment under the tipping platform for loading ramp * Including aluminum ramps, 8 t load capacity, 3.57 m long, stored in the ramp shaft under the tipping body * Front wall hot-dip galvanized * 4 UVV lashing rings LC 5000daN front and rear + 8 recessed, foldable lashing eyes LC 3000daN in the tipper floor (centrally aligned) * Stepless height-adjustable towing bar, hot-dip galvanized, towing eye 40 mm * Net hooks Kfedpfxoxmpd Ao Ab Uoa * Bolted, galvanized rear stanchions * One plastic toolbox on the right side of the chassis frame * Access step in front of the front wall ---- * We are a Müller-Mitteltal distribution partner ---- * e.g. €5 net per day with 60 months term, no down payment, no final installment. An offer by our financing partner FM LeasingPartner * We will gladly send you a non-binding offer. ---- Our business hours Monday - Thursday: 08:00 - 17:00 Friday: 08:00 - 15:00 Outside of business hours, we are available by appointment. Wir sprechen deutsch, we speak English, mowimy po polsku, on parle français, WhatsApp Leasing, financing, trade-in possible ----

Stanje: rabljeno, prva registracija: 11/2006, Leto izdelave: 2006, MÜLLER - MITTELTAL T4 Kompakt Vrtljiva prikolica - Nizkopodna prikolica z zračno vzmetenimi in jamskimi kolesi - 4 x zračno vzmetene GIGANT - osi - zračno vzmetenje - 4 x kolesne jame - mehanske nakladalne rampe - 2 zadnja podporna noga, zložljiva - izvlečne opozorilne table - ABS Kfjdpswmpbdofx Ab Uoa - MICHELIN pnevmatike: 235/75 R 17.5 - težka izvedba: 40.000 kg skupne mase - lastna teža: 8.400 kg - skupna dolžina: 11.750 mm - vlečna zanka: 50 mm Posebej primerna za prevoz strojev za rezanje apna! - nemška prikolica - Tehnični pregled / tehnični preizkus možen na zahtevo in za doplačilo! Pridržujemo si pravico do napak in vmesne prodaje!

Stanje: novo, največja dovoljena obremenitev: 38.900 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T5 profile 50.0: Kedjl Tihuspfx Ab Ujfa * Wabco EBS (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Last axle steering (axle lock for manoeuvring can be activated from the cab without additional truck-side installation, and additionally via a switch on the trailer); the lock must be disengaged before driving on public roads * Air suspension, lift and lowering system with RtR valve * 3rd axle liftable (ride height +30 mm with lifted axle) * Forced relief and forced lowering of the lift axle for manoeuvring (requires truck-side installation), speed-dependent activation via EBS * Smartboard infotool with pressure sensors for total axle load display per axle group * TPMS with display option in the truck via EBS signal (no truck-side installation required) * Mechanical warning sign kit for 3m total width * Drawbar 1,500 mm long with 50 mm towing eye and manual height adjustment * LED lighting system 12/24 V * Removable rear LED beacon * Toolbox, galvanised steel approx. 650 x 300 x 600 mm, mounted left side * Plastic fenders front axle, galvanised steel mud guards rear axle * Turntable platform extension with 45° corners and 3 storage compartments with lockable folding lids (lids open to rear) * Shortened low-loader deck by 500 mm to 6,280 mm incl. extended step by 500 mm to the front * Load securing package: 2 x 6.4 t lashing rings front corners, side front & rear corners each 2 x 13.4 t UVV lashing rings, 5 x 10 t UVV lashing rings per side (pivoting/lowering and loadable in all directions), 4 stake pockets per side additionally providing 2 t lashing option, 1 x 16 t UVV lashing ring on rear traverse * Rubber matting on folding ramp, approach slope, and low loader running surface * Bamboo wood inserted between main beams in excavator arm storage area * Extendable and folding outrigger extensions for 3 m total width (beam holder under chassis, right side) * Continuous excavator arm storage with reinforcement profile from last axle to rear cross member approx. L=2,350 x W=770 x H=270 mm, 2 pairs 6.4 t UVV lashing rings on sides * Hydraulic folding ramp with dual-line hydraulics and extendable tip section, approx. 4,650 x 720 mm incl. load-holding valves and hydraulic side shift * Hydraulic rear support * Hydraulic flow divider (for truck hydraulic capacity over 40 l/min up to 140 l/min) * Loaded platform height 890 mm +/- 20 mm (via air suspension) * Platform above turntable: 2,600 + 390 x 2,520 mm * Low-bed platform: 6,280 + 500 x 2,520 mm incl. 860 mm approach ramp * Chassis, turntable, drawbar, extension consoles, and access ramps hot-dip galvanised * Drawbar, axles, hydraulic axle supports, and air tanks painted black * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from week 14/2026

Stanje: rabljeno, številka stroja/vozila: 217, lastna masa: 3.450 kg, največja dovoljena obremenitev: 14.550 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 01/1993, vzmetenje: jeklo, velikost pnevmatike: 385/65 r22,5, medosna razdalja: 5.300 mm, barva: oranžna, Oprema: ABS, Drum brake Subject to errors and omissions Kfjdpfx Aonh Rzysb Uea

Stanje: rabljeno, največja dovoljena obremenitev: 13.860 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2022, dolžina tovornega prostora: 6.770 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 600 mm, prostornina tovornega prostora: 10 m³, Oprema: ABS, ? pocinkano ogrodje ? nizko spojeno ? vlečno uho 50 mm ? zaklep zabojnika ? po 12 priveznih obročkov na stran ? vzvratna kamera ? bobnaste zavore ? Duomatic priključek ? ABS ? zračno vzmetenje ? orodjarna ? EBS Ksdpsxb Iglsfx Ab Uefa ? podporne noge ? dvojne pnevmatike ? BPW osi Vsi podatki brez garancije / vmesna prodaja pridržana.

Stanje: rabljeno, lastna masa: 4.120 kg, največja dovoljena obremenitev: 13.880 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 03/2016, naslednji pregled (TÜV): 02/2026, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.360 mm, višina nakladalnega prostora: 900 mm, prostornina tovornega prostora: 10 m³, vzmetenje: zrak, velikost pnevmatike: 385/65R22.5, barva: rdeča, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Lokacija vozila: Bovenden, 2 osi, BPW osi, tandem, zračno vzmetenje, ABS (sistem proti blokiranju koles), zaščita proti podvozu, prednja opora, nihajna vrata. Nadgradnja: Tandemska prekucna prikolica z aluminijastimi stranicami, cca 10 m³, 2x 9t BPW osi, bobnaste zavore! Višina nakladanja cca 1510 mm! PODATKI O DODATNI OPREMI BREZ GARANCIJE, spremembe, vmesna prodaja in napake pridržane! Kfodpoxfli Eefx Ab Uea

Stanje: novo, največja dovoljena obremenitev: 14.300 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 4.995 mm, širina tovornega prostora: 2.380 mm, višina nakladalnega prostora: 900 mm, Oprema: ABS, Müller? Mitteltal KA-TA-R 19 Tandem Tipping Trailer with Bordmatik Left Side Inquiry Number: 11573 * BRAND NEW VEHICLE now finally available for immediate delivery!!! * Delivery free to your premises upon request. * Financing available through our partners FM LeasingPartner or MMV Leasing with terms from 24 to 72 months, with or without down payment, with or without final residual value. * Example: 60 months with no down payment and no residual value – €769 / month * Request your individual quote from us! We are an official Müller Mitteltal dealer. * ---- * Gross weight: 19t, Payload: 14.30t, RAL 9016 traffic white or custom paintwork upon request Kodpfswq Uihjx Ab Uefa * Reinforced and certified body built to EN 12642 XL including load securing certificate * Body – Steel 4,995mm x 2,380mm x 900mm * Right side with spring-assisted steel tailgate (2 springs), rear wall steel * Left side with Müller Bordmatic hydraulic sideboard (Bordmatik) * Removable roll tarpaulin for tipper * 4 pairs of lashing rings, recessed and foldable in 5mm steel floor, LC 3000 daN * LED lighting system 12+24 Volt replacing standard lighting * 2 LED reversing lights * Side marker lights with indicator function * BPW Eco axles, air suspension, drum brakes * 385/65R 22.5 tyres, with TPMS, EBS 2S/2M * 4 semi-round mudguards * Chassis, drawbar and foldable rear underrun protection hot-dip galvanized * Front wall platform with galvanized access step * Drawbar with 50mm eye, adjustable by +77mm / +33mm * Front support leg with crank * Foldable underrun protection for paver feeding * Removable protective grille for tail lights * ---- * Our business hours * Monday – Thursday: 08:00 – 17:00 * Friday: 08:00 – 15:00 * Outside business hours, appointments available by arrangement * We speak German, English, Russian, Polish, French * Leasing, financing, trade-in possible

Stanje: novo, največja dovoljena obremenitev: 27.940 kg, skupna masa: 36.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2025, * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes * 3 x 11 t axles * Air suspension with lift and lower function, including RtR valve * Start assist for shunting, applied to first axle via EBS – no truck-side installation – when lift axle is raised +30 mm ride height * Smart-Board installed on trailer as an info tool, with pressure sensors for total axle load indication * Rear axle as self-steering axle with electro-pneumatic steering lock * Steering lock for trailing axle controlled from driver’s cab for maneuvering purposes via EBS (no truck-side installation) * 2" king pin * 1 lift axle * Side underrun protection * Front aluminium drop support legs and rear swing-down supports on chassis * Alcoa LVL One aluminium wheels * 15-pin electrical connector * LED lighting 12/24 V * Removable rear LED beacon * 2 additional LED reverse lights * 2 LED work lights mounted on trailer sides – no truck-side installation * 7-pin power socket at rear for overlength lighting * Side marker lamps with indicator activation * Tyre pressure monitoring system with display in truck via EBS signal (no truck-side installation) * Mechanically adjustable warning sign sets front and rear * Straight steel fenders * Saddle platform with 45° bevelled front corners and front toolbox made of galvanized, powder-coated steel sheet (B = 2,480 x H = 500 x L = 665 mm), top hinged lid and side doors at the beveled corners * 400 mm aluminium side boards (RAL 9010 pure white) fold-down and removable, mounted laterally on the saddle platform * Rear wall –150 mm– slotted in * Tapered rear on the saddle platform to lowbed approx. 700 mm long with chequer plate covering and lashing bar at end for attaching aluminium ramps * Saddle and lowbed platform with 50 mm clamped wooden planks * Tear plate above the axles * Prepared for 3 mounting shafts under the saddle platform for optional aluminium ramps storage * Swing arm as a carrier for connection lines from truck to trailer Kfodpfxjwh Hdxj Ab Uja * Load securing package consisting of: outer frame of the saddle platform with punched holes, 45° bent and hole-pattern for lashing devices (2 t lashing force per point, min. 480 mm spacing), side-mounted 2 x 6.3 t recessed lashing rings per side, 1 x 16.5 t lashing ring per side at incline from lowbed to saddle platform, 2 pairs 16.5 t lashing rings in lowbed (1x on longitudinal beams after the step, 1x above the centre axle beside longitudinal beam), side 3 x 13.4 t lashing rings per outer frame (1x at start of platform step, 1x start of ramp slope, 1x end of ramp slope), 3 x 10 t each side (2x between front wheel recess and 1st axle, 1x between 2nd and 3rd axle), 3 x 5 t per side screwed to the wheel recess outer frames (2 at front, 1 at rear recess) * Extended excavator arm trough from end of last rigid axle over steering axle to end cross member, continuous with internal reinforcement profile approx. W = 770 mm x D rear = 270 / D front = 170 mm; each side 2 x 6.4 t lashing rings in the arm trough * Each side two wheel recesses, 390 mm deep and 640 mm wide for transporting wheel loaders with wheelbase 3,000–3,590 mm, tyre diameter up to 1,760 mm – retractable covers – * Second retractable cover ...

Stanje: rabljeno, številka stroja/vozila: 110, lastna masa: 8.320 kg, največja dovoljena obremenitev: 31.680 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2008, dolžina tovornega prostora: 10.300 mm, širina tovornega prostora: 2.550 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 r17,5, medosna razdalja: 6.500 mm, barva: modra, Oprema: ABS, * Drum brake Kedpfxjlpav Uj Ab Uofa * 4 axles * Wheelbase 6,500 mm * Hydraulic ramp length 2,850 mm – width 650 mm * Loading edge height 920 mm * Extendable to 3 m Subject to errors and omissions

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem equalizing unit * Tire pressure monitoring system with display capability in the truck via EBS signal, no truck-side installation required * Height-adjustable towing bar (up to 300 mm) with 40 mm flange towing eye * Mechanical landing gear at the front * Two mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, right side * 15-pin electrical connector * Multi-chamber tail lights * Bolted underrun protection * Plastic quarter mudguards * Net hooks on the sides and rear in the central locking mounts, plus two on the front wall * Main frame made of fine-grained steel * Steel pallet tipper body with rigid front wall made of smooth plate, continuous side walls – foldable without intermediate stakes, with drop side spring assist and with pendulum function via manual central locking * Bolted rear stanchions * Steel rear wall inserted in front of the ramps * Each corner with 1 x 5 t lashing point, plus 4 x 3 t lashing rings recessed in the outer frame on each side * 4 mm floor made of fine-grained steel * Two-part mechanical grid ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (manually retractable to 80 mm) Kfodotr St Hjpfx Ab Uea * Chassis, drawbar, rear stanchions, underrun protection, mechanical drop supports, as well as ramps, hot-dip galvanized * Axles, springs, air reservoir, flange towing eye and landing gear painted in black tone * Side walls and platform in RAL 9010 pure white * Painting of side walls and tipping platform in a RAL color of choice available at extra cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from calendar week 07/2026

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-ER 14.4 Flatbed: * Tire Pressure Monitoring System (TPMS) * EBS (Electronic Braking System) * Emergency Release Device for Spring Brake Cylinders * Drum Brakes * 2 x 7 t BPW Axles * Air Suspension with Lifting and Lowering System * Mechanically Adjustable 3 m Warning Sign Boards at Front and Rear * Towbar Height Adjustable by 300 mm, with 40 mm Flange Eye * Drawbar Shortened by approx. 200 mm to approx. 1,800 mm (Resulting in a B-Dimension of approx. 8,080 mm) * Front Landing Leg * Outward Folding Rear Support Legs * Plastic Toolboxes approx. 750 x 350 x 300 mm each, mounted on both the left and right sides * Side Impact Protection * Rear Underrun Protection * Plastic Quarter Mudguards * 15-Pin Electrical Socket * LED Lighting System 12 / 24 V Ksdpev D Tbksfx Ab Usfa * 2 Additional LED Reversing Lights at Rear (controlled via reverse gear) * 1 Removable LED Beacon (including bracket) at the rear * 400 mm high bolted front wall * 50 mm Softwood Floor * 2 Pairs of Container Locks (extendable to 3 m container external width) and lockable, locking dimension retracted per ISO - DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not DIN-compliant) for an overall external width of 3,000 mm * Perforated outer frame bent at approx. 45° with 2 t lashing capacity every 480 mm, installation of 3 t folding lashing rings possible every 600 mm – with 5 x 3 t UVV lashing rings fitted per side –, in each front and rear corner 1 x 6.3 t lashing ring (front, directly behind the container locks in the timber floor, and rear in the end cross member), various holes for 1.2 t lashing options in the front and rear cross members * 1 Pair of Aluminium Slide-In Ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tired and tracked vehicles * Rear storage compartment integrated into the chassis beneath the loading area * ---Chassis, drawbar, front wall, underrun protection, and rear supports hot-dip galvanized--- * Axles, air tanks, front landing leg, and flange tow eye painted in black * New vehicle with manufacturer’s warranty * Subject to prior sale and errors * Available from calendar week 09/2026

Stanje: novo, največja dovoljena obremenitev: 30.500 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Tire pressure monitoring with display capability in the truck via EBS signal - no on-truck installation required * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning sign packages front & rear * SmartBord infotool mounted with pressure sensors for total axle load display per axle group * Reflective contour tape on the sides and rear * Removable LED beacon at the rear * 15-pin power connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front closed individual plastic mudguards * Rear straight steel mud flaps each with spray suppression * Lateral underrun protection * Front section ahead of the turntable platform extended approx. 520 mm with 45° corners and 3 storage compartments incl. lockable folding lids (folding lids open to the rear) * Chassis made of high-strength fine-grained steel * Floor over the turntable platform made of 50 mm and in the low-bed platform made of 60 mm softwood * Outer planks of the loading ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing rings 6.4 t front left and right on the main frame of the turntable platform, 1 pair of 13.4 t lashing rings per side at the front and rear on the outer frame, plus 1 pair of 10 t lashing rings per side swivel- and lowerable, loadable in all directions and recessed in the outer frame, bolted 5 t lashing rings to the outer frames of wheel recesses (2 for the front and 1 for the rear wheel recess), 2 pairs of 6.4 t lashing rings at the side in the excavator arm recess * 11 pairs of folding outriggers for 3 m overall width (not at the rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for the extension boards made of sheet steel, mounted across the loading area in front of the 1st rear axle * Excavator arm trough above the rear axle to the end of the approach slope approx. 2,300 x 740 x 190 mm Kedpfx Asxmpydob Usfa * 2 wheel recesses per side, approx. 640 mm wide - front 340 mm deep, rear 220 mm deep - with retractable cover (storage for covers at the front of the turntable platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically extendable tip part approx. 4,650 x 720 mm * Hydraulic lateral ramp shift * Load platform above the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded platform height approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, turntable, folding outriggers, rear drop-down supports and loading ramps hot-dip galvanized * Axles, air tanks, and drawbar painted in black * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Errors and prior sale excepted * Available from CW 14/2026 * Sample images

Stanje: novo, največja dovoljena obremenitev: 30.500 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning sign packages at front and rear * SmartBord infotool installed with pressure sensors for total axle load display per axle group * Reflective contour tape on sides and rear * Removable LED beacon at rear * 15-pin electrical connector * LED tail lights * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Closed molded plastic single fenders at front * Straight steel rear fenders each with spray suppression (ant-splash) * Side underrun protection * Extension in front of the turntable platform approx. 520 mm with 45° corners and 3 storage compartments incl. lockable folding lids (lids open rearwards) * Chassis made of high-tensile fine-grained steel * Floor above turntable platform from 50 mm softwood, in low-bed platform from 60 mm softwood * Outer planks of ramps from 50 mm hardwood * Load securing package consisting of: 2 lashing eyes (6.4 t) at front left and right on main frame of turntable platform, 1 pair of lashing rings (13.4 t) at front and rear on side outer frame each, 1 pair of lashing rings (10 t) each side, pivoting and lowerable, loadable in all directions, recessed into the outer frame, 5 t lashing rings bolted to the outer frames at wheel recesses (2 each at front wheel recess, 1 at rear), 2 pairs of 6.4 t lashing rings at the excavator arm rest on the side * 11 pairs of folding outriggers for 3 m overall width (not in rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for ramp extension planks, made from sheet steel, transversely mounted in front of 1st rear axle * Excavator arm rest above rear axle to end of approach slope approx. 2,300 x 740 x 190 mm * 2 wheel recesses per side approx. 640 mm wide (front 340 mm deep, rear 220 mm deep) with slide-in covers (covers storage at front on turntable platform) for transporting wheel loaders with wheelbase 3,100–3,640 mm Kfjdpsxmpyksfx Ab Uea * Mechanical drop-down supports at rear * Hydraulic folding ramps with hydraulically extendable tip part approx. 4,650 x 720 mm * Hydraulic lateral ramp displacement * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded loading height approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, turntable, folding outriggers, rear supports, and ramps hot-dip galvanized * Axles, air tanks, and drawbar painted in black * Tires: 235/75R17.5 * Vehicle fully hot-dip galvanized * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from week 14 of 2026 * Sample images

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem equalizing unit * Tire pressure monitoring system with display capability in the truck via EBS signal, no installation required on the truck side * Height-adjustable drawbar (300 mm) with 40 mm flange towing eye * Mechanical landing gear at the front Ksdpfx Abotr Suce Ujfa * Rear: 2 mechanical folding support legs * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * 15-pin electrical connector * Multi-chamber tail lamps * Bolted underrun protection * Plastic quarter mudguards * Mesh hooks on the sides and rear in the central locking mounts, plus 2 hooks on the front wall * Main frame made of fine-grain steel * Steel pallet - 2-way tipper body, fixed front wall made of smooth sheet, continuous side walls (foldable without center stanchions, with drop-side spring assist mechanism), pendulum-type operation via manual central locking * Rear stanchions are bolted * Steel rear wall slides in front of the ramps * In each corner: 1 x 5 t lashing point; additionally, 4 x 3 t lashing rings each side, integrated into the outer frame * 4 mm floor made of fine-grain steel * Two-piece mechanical grating loading ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (manually retractable to 80 mm) * Chassis, drawbar, rear stanchions, underrun protection, mechanical drop-down supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and landing gear painted in black * Drop sides and platform in RAL 9010 pure white * Painting of side walls and tipping platform in any RAL color available for extra charge * New vehicle with manufacturer's warranty * Subject to prior sale and errors * Available from CW 07/2026

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-ER 14.4 Platform: * TPMS (Tire Pressure Monitoring System) * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 2 x 7-ton BPW axles * Air suspension with lifting and lowering system * Mechanically adjustable 3-meter warning panel sets, front and rear * Drawbar adjustable in height by 300 mm with 40 mm flange eye * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (thus B-dimension approx. 8,080 mm) * Landing gear/winch at the front * External foldable rear support legs * Plastic toolboxes approx. 750 x 350 x 300 mm each, on left and right sides * Side underrun protection * Rear underrun protection * Plastic quarter mudguards * 15-pin power plug * LED lighting system, 12 / 24 V * 2 additional LED reversing spotlights at the rear (wired via reverse gear) Kfsdpfev D Tbdsx Ab Uja * 1 removable LED beacon (incl. bracket) at the rear * 400 mm high bolted front wall * 50 mm softwood flooring * 2 pairs of container locks (extendable to 3 m exterior container width) and lockable; locking dimension retracted according to ISO-DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not DIN-compliant) with a total exterior width of 3,000 mm * Perforated outer frame, approx. 45 degree angled, with 2 t lashing capacity every 480 mm, possible installation of 3 t folding lashing brackets every 600 mm – on each side, 5 x 3 t UVV lashing brackets installed –, at each front and rear corner 1 x 6.3 t lashing ring (front directly behind the container locks in the wooden floor and rear in the end crossmember), various holes for 1.2 t lashing options in the front wall and end crossmember * 1 pair of aluminum insert ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tired and tracked vehicles * Rear storage compartment integrated below the loading area in the chassis * ---Chassis, drawbar, front wall, underrun protection, and rear supports hot-dip galvanized--- * Axles, air tanks, front landing gear, and flange eye painted in black * New vehicle with manufacturer warranty * Subject to errors and prior sale * Available from week 09/2026

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 2 x 7 ton Gigant axles * Parabolic springs with tandem compensation unit * Tire pressure monitoring with display capability in the truck via EBS signal, no installation required on truck side * Height-adjustable drawbar (300 mm) with 40 mm flange towing eye * Mechanical support winch at the front * Rear: 2 mechanical foldable supports * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * 15-pin electrical connector * Multi-chamber tail lights * Bolt-on underrun protection * Plastic quarter mudguards * Net hooks on sides and rear, integrated in the central locking bearings, plus 2 units on the front wall * Main frame made of fine-grain steel * Steel pallet 2-way tipper body with fixed smooth sheet front wall, continuous foldable side walls (without center stanchions, with sideboard spring lifters and manual central locking for swinging function) * Removable screw-on rear stanchions * Steel rear wall mounted in front of the ramps * In each corner: 1 x 5 ton lashing point; in each side: 4 x 3 ton lashing rings integrated into the outer frame * 4 mm floor made of fine-grain steel * Two-part mechanical grating loading ramps with aluminum tapered end, 2,150 + 1,300 mm x 600 mm (retractable to 80 mm manually) * Chassis, drawbar, rear stanchions, underrun protection, mechanical supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and support winch painted in black tone * Side boards and platform in pure white, RAL 9010 * Painting of side walls and tipper platform in any RAL color available at additional cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale Kedpfstr St Uex Ab Uofa * Available from calendar week 07/2026

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tyre pressure monitoring system * Emergency release unit for spring-actuated brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting/lowering system and RtR valve * Smard on-board weight measurement system * Warning sign packages front & rear * Reflective contour tape on sides and rear * Removable rotating beacon at the rear * LED lighting * Straight drawbar with 50 mm towing eye and infinitely height-adjustable * Tool box made of powder-coated steel sheet and basket-type spare wheel holder, right-hand side * Front closed individual plastic fenders * Rear straight steel spray guards with spray suppression * Lateral underrun protection * Turntable platform front extension by 520 mm with 45° corners and 3 recessed lockable storage compartments incl. covers * Chassis made of high-strength fine-grained steel * Turntable platform floor made of 50 mm and low-bed platform of 60 mm softwood * Outer planks of the drive-on ramps made of hardwood * Four stake pockets per side (stakes not included) and 2 t lashing point each * Lashing package comprising: Two 6.4 t lashing rings front left & right on the main frame of the turntable platform * Two pairs 13.4 t lashing rings at outer frame, front and rear, and four pairs per side 10 t lashing rings, swivel and height adjustable * Loadable in all directions and recessed into the outer frame * Two pairs 6.4 t lashing rings in the excavator arm rest area Kjdpfx Abol Tik No Uofa * Eight pairs galvanized folding outriggers for 3 m overall width (not in rear slope area) * Extension boards stored in a compartment on the left side * Excavator arm rest area above rear axle up to end of access ramp approx. 2,100 x 740 x 190 mm * Mechanical rear drop-down supports * Hydraulic folding ramps with hydraulically extendable ramp tips approx. 4,650 x 720 mm incl. hydraulic side-shifting ramps & load-holding valve * Deck area above slewing ring: approx. 2,990 x 2,520 mm * Rear load area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, turntable, drive-on ramps, folding outriggers, and mechanical drop-down supports hot-dip galvanized * Axles, drawbar, air tank, and slewing ring painted black * Tyres 235/75 R 17.5 * New vehicle without first registration, with manufacturer warranty * Subject to errors and prior sale * Available from CW 07/2025

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic brake system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting/lowering system and RtR valve * Smard-Board for load weight determination * Warning sign packages at the front & rear * Reflective contour tape on the sides and rear * Removable rear rotating beacon * LED lighting * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated sheet steel and spare wheel holder in basket design on right side * Front: closed single plastic mudguards * Rear: straight steel mud flaps with spray suppression * Side underrun protection * Turntable platform extended by 520 mm at the front, with 45° corners and 3 recessed, lockable storage compartments with lids * Chassis made of high-strength fine-grain steel * Decking over turntable platform made of 50 mm, and in low-bed platform of 60 mm coniferous timber * Outer planks of ramps made of hardwood * 4 stake pockets on each side (no stakes provided) with simultaneous 2 t lashing capability Kfsdpfx Abjl Tphrj Usa * Load securing package includes: 2 lashing eyes, 6.4 t, at the front left and right on the main frame of the turntable platform * On each side front and rear: 2 pairs of 13.4 t lashing rings on the outer frame and on each side 4 pairs of swiveling and lowerable 10 t lashing rings * Loadable in all directions, recessed into the outer frame * 2 pairs of 6.4 t lashing rings on the side in excavator arm recess * 8 pairs of galvanized folding outriggers for 3 m total width (not at the rear slope) * Widening planks stored in a side compartment on the left * Excavator arm recess over the rear axle to end of rear slope approx. 2,100 x 740 x 190 mm * Mechanical drop supports at rear * Hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm including hydraulic sideways ramp adjustment & load-holding valve * Loading deck over turntable: approx. 2,990 x 2,520 mm * Rear loading deck: approx. 6,780 x 2,520 mm * Load height loaded approx. 890 mm, +/- 20 mm (including 860 mm rear slope) * Flow divider installed * Chassis, turntable, loading ramps, folding outriggers, and mechanical drop supports hot-dip galvanized * Axles, drawbar, air reservoirs, and turntable painted in black * Tires: 235/75 R 17.5 * New vehicle, not previously registered, with manufacturer’s warranty * Errors and prior sale reserved * Available from CW 07/2026

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2025, * TS 3 Profile 30.0: * Wabco EBS-E (electronic braking system) * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco Plus axles * Air suspension with lift and lower system and RtR valve * Rear axle is self-steering with electro-pneumatic steering lock * Smartboard control box mounted as an information tool on the trailer, equipped with pressure sensors for total axle load display * Side underrun protection Ksdpsl Tnvgsfx Ab Uefa * Landing gears at front and rear with mechanical swing-down supports on the chassis * 15-pin electrical connector * LED lighting system 12/24V * Removable LED beacon on the rear left * Mechanically adjustable warning sign packages front and rear * Straight steel plate mudguards * Spare wheel holder on the right side under the chassis * Fifth wheel platform with 45° chamfered front corners and front-mounted toolbox made of galvanized steel (W = 2,480 x H = 500 x L = 665 mm) with folding lid * 400mm high aluminum side boards (RAL 9010 pure white), foldable and removable, on the fifth wheel platform * Rear wall – 150 mm – inserted high * Rear slope on the fifth wheel platform to low bed approx. 700 mm long * Fifth wheel platform with 50 mm wooden planks and low bed platform with 60 mm wooden planks * Tread plate over the axles * 8 x mechanical folding widenings to a total width of 3 meters, not at the rear slope (widening planks included, stored on the fifth wheel platform) * Load securing package: on the fifth wheel platform 2 x 6.3 t lashing rings per side, and 3 x 5 t lashing bars per side in the outer frame, in the low-bed platform per side 2 x 13.4 t lashing rings and 4 x 10 t folding/retractable lashing rings recessed in the outer frame, 2 x 6.4 t lashing eyes per side and 1 lashing ring in the excavator arm recess at the rear * Continuous excavator arm recess from the end of the last rigid axle over the steering axle to the end cross member, with internal reinforcement profiles (approx. L = 2,450 x W = 770 mm x D = 270 mm) * 2 x container locks directly after the neck in the low bed platform * Mechanically single-piece, hot-dip galvanized hydraulic loading ramps approx. 3,000 x 720 mm (mechanically adjustable laterally) * 4-way control block for future customer-side retrofit of hydraulic ramp shift * The outer board on the loading ramp is made of 50 mm hardwood * Hydraulic flow divider in the trailer (for truck hydraulic pump capacity from 40 l/min up to 120 l/min) * Loading area of the fifth wheel platform: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Unladen loading height approx. 910 mm (including 860 mm approach slope) * Saddle height approx. 1,220 mm (suitable for 2- and 3-axle tractors) * Chassis, ramps, rear folding supports, widening consoles hot-dip galvanized * Axles, landing gears, air tanks painted in a black tone * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Errors and prior sale excepted * Available from week 16/2026

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: * Wabco EBS-E (electronic braking system) * RDÜ (tire pressure monitoring system) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco Plus axles * Air suspension with lift and lower function, as well as RtR valve * Last axle steering with electro-pneumatic steering lock * Smartboard control box mounted on the trailer as info tool with pressure sensors for total axle load display * Side underrun protection * Landing gear at front and mechanical swing-down supports at rear of chassis * 15-pin power connector * LED lighting system 12/24V * LED rotating beacon (removable) at rear left * Mechanically adjustable warning sign packages front and rear * Straight steel mudguards * Spare wheel holder underneath chassis, right side Kfjdpspk D I Asfx Ab Uoa * Fifth wheel platform with 45° chamfered front corners and front tool box made of galvanized sheet steel, W = 2,480 x H = 500 x L = 665 mm with folding lid * Side of the fifth wheel platform equipped with 400 mm high aluminium drop-side boards (RAL 9010 pure white), foldable and removable * Removable rear wall – 150 mm high * Rear ramp on fifth wheel platform to lowbed, approx. 700 mm long * Fifth wheel platform fitted with 50 mm timber planks, lowbed platform with 60 mm timber planks * Chequer plate above the axles * 8 x mechanical foldable extensions to 3 m overall width (excluding rear ramp area), extension planks available with storage platform * Lashing package: On the fifth wheel platform, 2 x 6.3 t lashing rings each and 3 x 5 t lashing bars per side on the outer frame; on the lowbed platform, 2 x 13.4 t lashing rings per side plus 4 x 10 t lashing rings, pivotable and lowerable, fitted in the outer frame; 2 x 6.4 t lashing eyes per side plus 1 lashing ring in the excavator stick recess at rear * Excavator stick recess, running continuously from end of last fixed axle over the steering axle to the closing crossmember, with internal reinforcement profile, approx. L = 2,450 x W = 770 x D = 270 mm * 2 x container locks directly after the step in the lowbed platform * Mechanically operated one-piece hot-dip galvanized hydraulic ramps, approx. 3,000 x 720 mm (mechanically adjustable in width) * 4-way control block for later customer retrofitting of hydraulic ramp displacement * Outer board on ramp made of 50 mm hardwood * Hydraulic flow divider in the trailer (for truck hydraulic pump output from over 40 l/min up to 120 l/min) * Loading area of fifth wheel platform: approx. 3,935 x 2,480 mm * Lowbed loading area: approx. 8,500 x 2,520 mm * Loading height unladen approx. 910 mm (including 860 mm drive-on ramp) * Fifth wheel height approx. 1,220 mm (suitable for 2- and 3-axle tractor units) * Chassis, ramps, rear folding supports, widening consoles hot-dip galvanized * Axles, landing gear, air tanks painted in black * Hydraulic flow divider * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from week 16/2026

Stanje: novo, največja dovoljena obremenitev: 5.840 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2025, * KWH 8.8 ML: * TPMS (Tire Pressure Monitoring System) * EBS braking system * Drum brakes * BPW axle * Parabolic springs * Support winch at the front * Spring-assisted square tube support legs at the rear with base plates and safety lock pins for various support heights * Drawbar with 40 mm bolt coupling (height-adjustable) * 15-pin electrical connector * LED lighting Ksdpeu I Iqxjfx Ab Uofa * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and cross members * Enclosed steel fenders with splash guards * Closed side underrun protection, usable as advertising space * Plastic toolbox with base insert (installed horizontally), approx. 500 x 350 x 400 mm * Swiveling cable drum assembly, clear width between the drum arms 1,700 mm, with tension lock for fixing the drum at the support arm ends, as well as a central claw lock for securing the cable drum assembly to the chassis * Motor-hydraulic drum drive with oil motor * Valves and adjustable drive rollers with rubber lining * Hydraulic speed regulator and brake for the drum drive * Steel drum shaft, 76 mm in diameter, with centering and rotating ends * 1 pair of stepped centering cones made of polyamide * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) * Finish: hot-dip galvanized * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf