Müller-Mitteltal Eal Prikolice nakup rabljenega (245)

Stanje: novo, največja dovoljena obremenitev: 6.110 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2025, * KWH 8.8 ML: * TPMS (Tire Pressure Monitoring System) * EBS braking system * Drum brakes * BPW axle * Parabolic springs * Support winch at the front * Spring-assisted square tube supports at the rear with base plate, safety locking pins for various support heights * Drawbar with 40 mm screw-in towing eye (height adjustable mm) * 15-pin electrical connector Kedpfsu I Iqfex Ab Heww * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and crossbeams * Enclosed steel mudguards with splash protection * Enclosed lateral underrun protection, usable as advertising space * Plastic toolbox with base insert (horizontal installation) approx. 500 x 350 x 400 mm * Swiveling cable drum assembly, width between drum arms 1,700 mm, with tension lock for securing the drum at the support arm ends, as well as locking of the cable drum assembly to the chassis via a centrally positioned claw lock * Motor-hydraulic drum drive with oil motor * Valves and adjustable rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft with 76 mm diameter, with centering and rotating ends * 1 pair of centering cones made of polyamide, stepped * Hydraulic pump unit with petrol engine, including hand and electric starter * Fuel tank and hand starter * 13 HP with gear pump (150 bar) * 315/80 R 22.5 tires * 2,690 kg unladen weight * Vehicle hot-dip galvanized * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available in Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.620 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 600 mm, Leto izdelave: 2026, * KA-TA-R 14.4: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal—no truck-side installation required * Drum brakes * 2 x 7 ton Gigant axles * Parabolic springs with tandem equalizer assembly * Height-adjustable drawbar (approx. 300 mm) with 40 mm flange towing eye * Jost mechanical landing gear at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm mounted at the front right side of the chassis * 15-pin power connector * LED tail lights 12/24 V * Bolt-on underrun protection * Plastic quarter mudguards * Net hooks in the central locking area as well as 2 on the front wall * Chassis made of fine-grain steel * Steel pallet 3-way tipper body with reinforced Strong sideboards (continuous upper side walls with internal reinforcement tube—without center stanchions—can be folded down with board wall assist spring) * Bolted rear stanchions * Combination steel swing rear doors, 2-wing asymmetrically split, swiveling and lockable up to 270°—not foldable—additionally with pendulum frame for automatic tailgate opening during tipping process, locking via galvanized rotary bar lock at rear and central locking system, deactivation function for automatic tailgate when tipping backwards with opened swing door * Each corner fitted with 1 x 5 ton lashing point and 4 x 3 ton lashing rings on each side, recessed into the outer frame * 4 mm floor plate made of fine-grain steel * Rear guide rail for loading ramps * Reinforced body with load securing certificate * 1 pair aluminum loading ramps approx. 3,570 x 410 mm (load capacity 10 tons/pair), suitable for pneumatic-tyre and tracked vehicles * Lockable storage compartment from the rear, recessed under the loading deck in the chassis for the ramps * Drawbar, underrun protection, rear stanchion, and rear folding supports hot-dip galvanized * Axles, springs, air tank, and landing gear painted in a black tone * Tires: 358/55 R 19.5 * Sideboard paint finish in RAL 9010 pure white * Custom RAL colors for side walls available at extra cost * Errors and prior sale excepted * Immediately available from calendar week 10/2026 Kjdpfxjx Hm Rio Ab Heww * Sample images

Stanje: novo, največja dovoljena obremenitev: 10.620 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 600 mm, Leto izdelave: 2026, * KA-TA-R 14.4: * Wabco EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Tyre pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem equaliser unit * Drawbar height adjustable by approx. 300 mm, with 40 mm flange towing eye * Jost mechanical landing gear at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm on the right-hand side at the front of the chassis * 15-pin power connector * LED taillights 12/24 V * Bolt-on underrun protection * Plastic quarter mudguards * Net hooks at the central lock bearings as well as 2 at the front wall Ksdpfx Abjx Hm Rcs Heww * Chassis made from high-tensile fine-grain steel * Steel pallet 3-way tipper body with reinforced Strong side walls (continuous upper side walls with internal tube reinforcement — without central stanchions — foldable with drop-side spring assistance) * Rear stanchions bolted * Combination steel double-wing rear door, asymmetrically split, can be swung and locked 270°, not foldable, with additional pendulum frame for automatic tailgate opening when tipping, locking via galvanised rotary bar latch at the rear and central locking, deactivation function for automatic rear door operation when tipping in reverse with open wing door * Lashing points: 1 x 5 t per corner and 4 x 3 t per side, integrated in the outer frame * 4 mm floor plate made of fine-grain steel * Rear ramp receiving rail * Reinforced body with load securing certificate * 1 pair aluminium loading ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tyred and tracked vehicles * Lockable rear storage compartment recessed beneath the loading surface in the chassis for ramps * Drawbar, underrun protection, rear stanchion, and rear folding supports hot-dip galvanised * Axles, springs, air tank, and landing gear painted in black * Tyres 358/55 R 19.5 * Sideboard coating in RAL 9010 pure white * Side wall paint in an RAL colour of choice available at extra cost * Errors and prior sale excepted * Available immediately from calendar week 10/2026 * Sample images

Stanje: rabljeno, največja dovoljena obremenitev: 5.900 kg, skupna masa: 9.000 kg, konfiguracija osi: 2 osi, prva registracija: 05/2020, dolžina tovornega prostora: 5.370 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, prostornina tovornega prostora: 5 m³, Oprema: ABS, * ABS * 5-komorna zadnja svetla * Podesivi vučni uređaj po visini Kwedpfx Aboyncyho Hew * Gigant osovine * Prednji oslonac na navijanje ----Nadgradnja: Niskopodni prikolica, približna visina utovara 870 mm, zadnji deo zakošen, visina uspona približno 780 mm, opružno rasterećene čelične stranice levo i desno, drveno dno, prstenovi i ušice za vezivanje. Opružno rasterećene i bočno pomične rampe za uspon sa vatrootpornim i protivkliznim rešetkastim prečkama od pocinkovanog čelika (dužina cca 2.600 mm), automatska zadnja podrška povezana s upravljanjem rampama, plastična kutija za alat ispred prednjeg zida. Šasija/prednji zid/vučno vratilo/zadnji zid/rampe i stubići pocinkovani. Prodaja isključivo pravnim licima. KOD IZVOZA SE PLAĆA SAMO CENA BEZ PDV-A!!!!! SVE INFORMACIJE BEZ GARANCIJE, POSEBNO OPREMA I DODACI. Osnov za sve kupoprodajne ugovore, fakture, profakture, narudžbine i prodajne razgovore su naši Opšti uslovi poslovanja (vidi Impressum).

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal ETÜ-TA-R 14.4 Tandem | Low Loader | Platform | Trailer Kwsdpoyndh Hofx Ab Hjw Available immediately | Reference number for inquiries: 11611 | Delivery to your address possible * We are happy to provide you with an individual offer * ---- * Gross weight: 14.4 t, Payload: 10.95 t * LED lighting system * GIGANT axles, EBS, twin tires 235/75R 17.5, parabolic springs * Tire pressure monitoring system (TPMS) * 6.27 m x 2.47 m platform with galvanized 400 mm front wall * Excavator bucket rest made of hardwood, bolted to the front wall * Floor height unladen 930 mm / laden 870 mm * One-piece ramps with hot-dip galvanized grid surface, slip-resistant design, retractable down to approx. 20 mm. Secured by retaining bar and diagonal brace * Ramp lifter with upright, adjustable springs for easy one-man operation * 4 UVV drop lashings (LC 6300 daN) * Perforated outer frame (45°-bent with hole pattern for lashing equipment, lashing force per lashing point LC 2000 daN at a minimum spacing of 480 mm. Installation of drop lashings LC 3000 daN at approx. 600 mm spacing possible), closely spaced cross-stiffeners, high-ribbed front and rear closure with rear loading ramp, hot-dip galvanized * 10 UVV lashing rings LC 3000 daN retractable in the existing hole grid in the outer frame, additional * Additional lashing options via bore holes (Ø 50 mm, LC 1200 daN) in the front and rear crossmembers * Toolbox in front of the front wall * Side marker lights with indicator function * 50 mm thick softwood floor. Chassis hot-dip galvanized * Height-adjustable landing gear at the front, folding supports at the rear * Retrofitting of 2 container locks possible * Drawbar with 40 mm towing eye (hot-dip galvanized), height adjustable, 50 mm eye possible on request * 1 removable LED warning light at the rear * ---- * Leasing, hire purchase, financing, trade-in possible * Example: 510 euros for 60 months’ term, no down payment, no final installment * ---- * Our opening hours: * Monday - Thursday: 08:00 - 17:00 * Friday: 08:00 - 15:00 Outside of business hours, viewings possible by appointment. We speak German, English, Polish, and French Leasing, financing, trade-in possible

Stanje: novo, največja dovoljena obremenitev: 16.400 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2024, * T3 Profile 30.0: * EBS-E (Electronic Braking System) * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11-ton BPW Eco axles * Air suspension with lift/lower system * SmartBoard as trailer infotool with pressure sensors for axle load display per axle group * Side underrun protection * Mechanically adjustable warning panels front and rear * Front axle: closed plastic mudguards; rear axle: straight galvanized steel skirts, each with spray protection * Folding (hot-dip galvanized) lid for the toolbox on the bogie platform * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm (black powder-coated) mounted right side * 15-pin electrical connector * LED lighting 12/24 V * LED beacon (removable) at rear * Side marker lights with indicator function * Drawbar with 40 mm towing eye and height adjustment via traction spring and turnbuckle * Tire pressure monitoring system with display option in truck via EBS signal (no truck-side installation required) * Rubber lining on folding ramps as well as on the access slope, left and right (approx. 860 mm long) * Rubber lining on the longitudinal beams from front to rear crossmember * Hardwood floor on the running surfaces of the low-bed platform * Each side with 4 stake pockets, with simultaneous 2-ton lashing capacity * Load securing package consists of: 5 pairs of UVV lashing rings, swiveling and lowerable, loadable in all directions and integrated in the outer frame—in the corners 13.4 tons, elsewhere 10 tons * 6 pairs of mechanical folding outriggers for total width of 3 meters (not possible in rear slope) * Board holder under the loading area, lengthwise * Roller stop raised in front of front crossmember with 1 x 6.4-ton lashing eye on each side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable tip section and load-holding valves * Hydraulic lateral ramp shift * Hydraulic rear support (single-stage cylinder) Kwsdpfx Absq Dyvco Hsw * Hydraulic flow divider in trailer (for hydraulic pump flow in truck over 40 to max. 140 l/min) * Hydraulic control block splash-proof * Two-line hydraulics * Platform over kingpin: approx. 1,960 x 2,520 mm * Rear platform: approx. 6,500 x 2,520 mm (including 860 mm access slope) * Loaded deck height approx. 890 mm +/- 20 mm (air suspension) * Chassis, bogie, roller stop, folding width extensions & loading ramps hot-dip galvanized * Axles, turntable, drawbar, air tank, etc. painted black * Loaded height: approx. 890 mm +/- 20 mm * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from calendar week 20 of 2026

Stanje: novo, največja dovoljena obremenitev: 20.500 kg, skupna masa: 27.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TR 27.0 flatbed: * EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lifting and lowering function, including RTR function * 1st axle liftable * Last axle as trailing steering axle with electro-pneumatic steering lock via reverse PIN (lock of the trailing axle from the tractor for maneuvering purposes – no installation required on the truck side – connected via PIN 10 in the 15-pin connector, for maneuvering only, not for public road use) * SmartBoard control box as an infotool with pressure sensors for total axle load display * Tire pressure monitoring with display option in the truck via EBS signal, no installation required on truck side * Fixed center drawbar with 50 mm flanged towing eye (loaded 900 mm, height adjustment at head plate) * Mechanical landing gear at the front, mechanical swiveling supports at the rear of the chassis * Hydraulic flow divider * Continuous side walls (without center stanchion) up to the approach slope * Folding rear stanchions * Steel rear wall slid in front of the rear stanchions * Mechanically adjustable warning panel kit at front and rear * Toolbox made of galvanized sheet steel – black powder-coated – approx. 650 x 300 x 600 mm, mounted right side * 15-pin electrical connector * LED tail lights * Removable LED beacon including bracket and installation Kwedpor Dpzxofx Ab How * 2 x LED reverse lights at rear of vehicle (activated via reverse gear) * Flashing LED side marker lights * 60 mm larch/Douglas fir wooden floor * 400 mm plug-in steel front wall * Perforated outer frame, approx. 45° bent, with provisions for mounting 3 t drop lashing brackets * In each corner 1 x 10 t lashing ring, additionally on each side 2 x 10 t and 3 x 6.3 t lashing rings * Various holes for 1.2 t lashing options in front and end crossmembers * Hydraulic one-piece loading ramps, approx. 3,000 x 720 mm, mechanically adjustable laterally * 4-section hydraulic control block for possible retrofitting of hydraulic ramp sliding * Chassis, drawbar, front wall, mechanical rear supports, loading ramps hot-dip galvanized * Axles, air tanks, flanged towing eye, and front landing gear painted in a shade of black * Hydraulic flow divider in the trailer (for truck-side hydraulic pump capacity of over 40 l/min up to 120 l/min) * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Available from week 13/2026 * Sample pictures (photos of the vehicle may differ due to special equipment)

Stanje: novo, največja dovoljena obremenitev: 20.500 kg, skupna masa: 27.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TR 27.0 Flatbed: * EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 9 t BPW Eco-axles * Air suspension with lift/lower system and RTR function * 1st axle liftable Ksdpfxsr Dpz Ao Ab Hjww * Rear axle as trailing steering axle with electro-pneumatic steering lock via PIN in reverse gear (locking of the trailing axle from the towing vehicle for maneuvering purposes – no installation required on truck side – assigned to PIN 10 in the 15-pin connector, only for maneuvering, not for use on public roads) * SmartBoard operating box as infotool with pressure sensors for total axle load display * Tire pressure monitoring with display option in the truck via EBS signal, no installation required on truck side * Fixed central drawbar with 50 mm flange eye (loaded 900 mm, height adjustment at the head plate) * Mechanical landing leg at the front, mechanical swivel supports at the rear on the chassis * Mechanically adjustable warning board package front and rear * Toolboxes made of galvanized sheet steel – black powder-coated – approx. 650 x 300 x 600 mm mounted on right-hand side * Hydraulic flow divider * Continuous side walls (without center stake) up to the drive-on slope * Folding rear posts * Steel rear wall inserted in front of the rear posts * 15-pin electrical plug * LED tail lights * Removable LED beacon including bracket and installation * 2 x LED reversing lights at vehicle rear (activated by reverse gear) * Flashing LED side marker lights * 60 mm larch/douglas fir timber floor * 400 mm steel front wall slotted in place * Perforated outer frame approx. 45° angled, with provision for mounting 3 t folding lashing rings * 1 x 10 t lashing ring at each corner, plus 2 x 10 t and 3 x 6.3 t lashing rings per side * Various holes in the front and rear crossmembers for 1.2 t lashing capability * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm, mechanically adjustable laterally * Four-way hydraulic control valve for potential retrofit of hydraulic ramp shifting * Chassis, drawbar, front wall, rear mechanical props, loading ramps, and tailgate hot-dip galvanized * Axles, air tanks, flange eye, and front landing leg painted in black * Hydraulic flow divider in trailer (for hydraulic pump output in truck from over 40 l/min to 120 l/min) * New vehicle with manufacturer’s warranty * Errors and prior sale reserved * Available from week 13/2026 * Sample pictures (photos of the vehicle may differ due to special equipment)

Stanje: novo, največja dovoljena obremenitev: 16.400 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2024, * T3 Profile 30.0: * EBS-E (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Air suspension with lifting and lowering function * SmartBoard as information tool on the trailer with pressure sensors for axle load display per axle group * Side underrun protection * Manually adjustable warning sign sets at front and rear * Front axle closed plastic mudguards and rear axle straight galvanized steel skirts, each with splash guards * Hinged lid (hot-dip galvanized) for the toolbox on the turntable platform * Toolbox made of galvanized sheet steel, approx. 650 x 300 x 600 mm (black powder-coated), mounted right side * 15-pin electric connector * LED lighting 12 / 24 V * Removable LED beacon at the rear * Side marker lights with indicator control * Drawbar with 40 mm towing eye and height adjustment by tension spring & turnbuckle * Tire pressure monitoring system with display option in the truck cab via EBS signal (no in-truck installation required) * Rubber covering on folding ramps as well as on drive-up slopes left and right (approx. 860 mm long) * Rubber covering on longitudinal beams from front to end crossmember * Hardwood flooring on the running surfaces of the low-bed platform * Four stake pockets per side, each with 2 t lashing capacity * Load securing package consists of: 5 pairs of UVV-compliant lashing rings, tilting and retractable, loadable in all directions and recessed into the outer frame - in the corners 13.4 t, otherwise 10 t * Six pairs of manual folding extensions for 3 m total width (not at rear slope) * Plank holder under the loading platform, longitudinal direction * Raised roller stop before front crossmember with one 6.4 t lashing eye per side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extended ramp tip and load-holding valves * Hydraulic lateral ramp shift * Hydraulically operated rear support (single-stage cylinder) * Hydraulic flow divider in the trailer (for hydraulic pump output in truck over 40 l/min up to max. 140 l/min) * Hydraulic control block, splash-proof * Two-line hydraulic system * Loading area above slewing ring: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (including 860 mm run-up slope) * Loaded loading height: approx. 890 mm +/- 20 mm (air suspension) * Chassis, turntable, roller stop, folding extensions & drive-up ramps hot-dip galvanized * Axles, slewing ring, drawbar, air tanks, etc. painted in black tone Kjdotplv Nspfx Ab Howw * Loaded loading height: approx. 890mm +/- 20mm * New vehicle with manufacturer warranty * Subject to errors and prior sale * Available from week 20/2026

Stanje: novo, največja dovoljena obremenitev: 13.410 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 4.995 mm, širina tovornega prostora: 2.380 mm, višina nakladalnega prostora: 900 mm, prostornina tovornega prostora: 11 m³, Leto izdelave: 2026, * Wabco EBS-E (electronic braking system with RSS) * Emergency release device for spring-loaded cylinders * Drum brakes * Tire pressure monitoring system with display option in the truck dashboard via EBS signal (no truck-side installation required) * 2 x 9-ton Gigant axles * Air suspension with ride height control during tipping operation * Drawbar with 50 mm flange-type towing eye (adjustable by +77 mm and -33 mm via offset plate) * Jost landing gear at the front * Foldable galvanized steel underrun protection for paver loading * Closed individual plastic mudguards * Standing platform on the front wall * Manual sliding tarpaulin * 15-pin electrical connector * LED tail lights with galvanized protective cover * Chassis made of high-tensile fine-grained steel * Steel 3-way tipper body (side walls with full-length MM profile, without central stanchion, pendulum-mounted with manual central locking and foldable left-side wall with drop-side spring lift) * Sliding tarpaulin in RAL 7038 agate grey, tarpaulin tensioned with lateral ratchet straps and front/rear tensioning bungees * Front wall platform made of grating with access step at the drawbar and a handrail on the front wall * Rear wall made of HBW 400 steel, pendulum-mounted with automatic two-hook lock * 5 mm steel floor made of HBW 450 steel * 4 x 3-ton recessed and foldable lashing rings per side, embedded into steel floor * Reinforced and certified body according to EN 12642 XL incl. load securing certificate up to 19 tons * Tipping bridge and side walls in RAL 9010 pure white * Sideboard panels painted in RAL 9010 pure white * Painting of side walls in any RAL colour possible at extra cost * Chassis painted in RAL 9011 graphite black * New vehicle with full manufacturer's warranty * Errors and prior sale reserved * Immediately available ex Egestorf Kwjdpfjxl Nkgsx Ab Hsw

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal ETÜ-TA-R 14.4 Tandem Low Loader ? Platform ? Trailer Immediately available | Inquiry No.: 27678 | Delivery to your address possible * We are happy to provide you with an individual offer * ---- * GVW: 14.4t, Payload: 10.95t * LED lighting system * GIGANT axles, EBS, twin tires 235/75R 17.5, parabolic springs * Tire pressure monitoring system (TPMS) * 6.27m x 2.47m platform with galvanized front wall, 400mm high * Excavator bucket rest made of hardwood, bolted to the front wall * Deck height unladen 930mm / laden 870mm * One-piece ramps with hot-dip galvanized grid grating, anti-slip design, can be pushed together to approx. 20 mm, secured by retaining rods and diagonal supports * Ramp lift with vertically mounted, adjustable springs for easy single-person operation Kodpfx Absyadz Re Hjww * 4 UVV drop lashing rings (LC 6300 daN) * Perforated outer frame (45° angled with hole pattern for lashing equipment, lashing force per point LC 2000 daN with a minimum spacing of 480 mm. Installation of drop lashing rings LC 3000 daN at approx. 600 mm intervals possible) with close cross profiling, high-webbed front and rear closures and rear drive-on slope, hot-dip galvanized * 10 UVV lashing rings LC 3000 daN, retractable into existing hole grid in outer frame, additionally * Further lashing points by drilled holes (Ø 50 mm, LC 1200 daN) in the front and rear crossmember * Toolbox in front of the bulkhead * Side marker lights with indicator function * Softwood floor, 50 mm thick. Chassis hot-dip galvanized * 2 container locks recessed in the front crossmember * Height-adjustable telescopic landing gear at the front, fold-down supports at the rear * Drawbar with 40 mm towing eye (hot-dip galvanized), height adjustable; 50 mm eye available on request * 1 removable LED warning beacon at the rear ---- * Leasing, hire-purchase, financing, trade-in possible * For example: 515 euros at 60 months term, no down payment, no final installment * ---- * Our opening hours * Monday - Thursday: 08:00 - 17:00 * Friday: 08:00 - 15:00 Outside opening hours available by appointment We speak German, English, Polish, French Leasing, financing, trade-in possible

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 02/1992, Leto izdelave: 1992, Oprema: ABS, Müller-Mitteltal roll-off prikolica Nemško vozilo Kjdpfx Aext Sd Ssb Howw = Dodatne informacije = Lastna masa: 3.140 kg Nosilnost: 14.860 kg Skupna dovoljena masa: 18.000 kg Prodajna cena: € 1.500, US$ 1.771

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 09/1993, Leto izdelave: 1993, Oprema: ABS, = Additional Options and Accessories = - Electronic Braking System (EBS) = Notes = Müller-Mitteltal lowbed trailer 2-axle low loader ZSA Drive-on ramps IDNR 892 Processing We are happy to provide you with advice, contract signing, or vehicle collection at our dealership. Please schedule an appointment. If you are unable to visit us in person, we offer complete processing via telephone/email/WhatsApp/fax. Upon request, we can deliver your new vehicle directly to your door. This ensures you receive the best price, maximum security, and convenience when taking delivery. We are also happy to accept your used vehicle as a trade-in. We offer the option of a digital vehicle evaluation based on your vehicle photos, even without visiting the dealership. Our specialized purchasing team guarantees you the highest possible price. Upon request, we can deliver your new "used" vehicle nationwide directly to your doorstep and take your old vehicle in part-exchange. Financing – Leasing Immediate approval and settlement of existing financing. Your specialist partner for passenger cars, transporters, commercial vehicles, and construction machinery. ITC GmbH & Co. KG Siemensstraße 7 32312 Lübbecke (industrial area) Constantly over 400 vehicles in stock. The information provided in advertisements, on the internet, price tags, and images are non-binding descriptions and do not constitute guaranteed features. The seller assumes no liability or warranty for errors in typing or data transmission. Listed equipment may need to be checked separately. Offers are generally made without new TÜV approval; we will be happy to provide you with an offer via our partner workshop. Errors and prior sale excepted. = Further Information = Unladen weight: 4,600 kg Kedpfx Asxt Rw Rjb Hsww Payload: 13,400 kg Gross vehicle weight: 18,000 kg Sales price: €6,500, US$7,673

Stanje: novo, največja dovoljena obremenitev: 10.500 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ - TA -R 14.4 ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders Kwodsx Ipapepfx Ab Hjw * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating aggregate ----Drawbar / Drawbar Eye: * Drawbar adjustable in height by 300 mm – drawbar extension by 250 mm to 2,250 mm * 40 mm flanged drawbar eye ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal (no truck-side installation required) * 15-pin power connector * LED tail lights 12 / 24 V * LED rotating beacon (removable) at rear ----General Attachments: * Support winch in front * Externally mounted hot-dip galvanized folding supports at rear * Plastic toolbox approx. 858 x 500 x 500 mm, front right, outside at the front wall * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * Preparation in front of front wall for retrofitting container locks * Bolted front wall made of smooth sheet metal * Sidewalls made of trapezoidal profile steel sheet, foldable with drop-side spring-assisted lifting device * Steel rear wall can be slid between the ramps – storage bracket for unused rear wall inside by the front wall * Rear stanchions bolted * Rear approach angle approx. 860 mm ----Flooring: * 50 mm softwood floor * 12 mm thick and 270 mm wide rubber strips on the inside of ramps * 12 mm thick and 210 mm wide rubber strips on the approach slope and externally on the low-bed platform (from front wall to end sill) ----Load securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Installation of 3 t drop lashing rings every 600 mm possible * 1 x 6.3 t lashing ring at each front and rear corner * Various drill holes in front wall and end sill for 1.2 t lashing options ----Ramps: * One-piece mech. grating ramps with spring system for one-man operation, approx. 2,750 x 870 mm (can be compressed to 20 mm) ----Paintwork: * Chassis, drawbar, front wall, tailgate, and ramps hot-dip galvanized * Axles, springs, air tank, and flanged drawbar eye painted black * Sidewalls painted RAL 9010 pure white ----Info: * --Reinforced and certified body according to EN 12642 XL incl. load securing certificate-- * Errors and prior sale excepted * New vehicle with manufacturer’s warranty ----Delivery time: Vehicle is immediately available

Stanje: novo, največja dovoljena obremenitev: 10.500 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * First inspection (ETÜ) - TA -R 14.4 ----Brake System: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with equalizing unit ----Drawbar / Flange Eye: * Height-adjustable drawbar by approx. 300 mm - drawbar extension by 250 mm to 2,250 mm total length * 40 mm flange-type towing eye ----Electrics / Lighting: * Tire pressure monitoring with display option in the truck via EBS signal (without truck-side installation) * 15-pin electrical connector * LED rear lights 12 / 24 V * Removable LED beacon at rear ----General Attachments: * Landing leg at the front * Externally mounted hot-dip galvanized folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, externally mounted on the front right end wall * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * Preparation in front of the bulkhead for later installation of container locks * Bolted smooth steel bulkhead * Foldable steel side walls with trapezoidal profile, with drop-side spring assist * Removable steel rear wall, stowable inside at the front of the bulkhead when not in use * Bolted rear stanchions Kwodpfxex Ipbas Ab Hsw * Rear ramp bevel approx. 860 mm ----Flooring: * 50 mm softwood flooring * 12 mm thick and 270 mm wide rubber strips on the inside of the loading ramps * 12 mm thick and 210 mm wide rubber strips on the ramp bevel and on the exterior of the low loader platform (from front bulkhead to rear cross member) ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Possible installation of 3 t folding lashing rings every 600 mm * 1 x 6.3 t lashing ring in each of the front and rear corners * Various drillings in the front and rear cross members for 1.2 t lashing options ----Ramps: * One-piece mechanical grating ramps with spring assistance for single-person operation, approx. 2,750 x 870 mm (collapsible to 20 mm thickness) ----Paint Finish: * Chassis, drawbar, front wall, tailgate, and ramps hot-dip galvanized * Axles, springs, air tanks, and flange eye painted in black * Side walls painted in RAL 9010 pure white ----Information: * Reinforced and certified superstructure according to EN 12642 XL, including load securing certificate * Subject to errors and prior sale * New vehicle with manufacturer’s warranty ----Delivery time: Vehicle is immediately available ex Eggerstorf

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 04/2005, barva: črn, Leto izdelave: 2005, Oprema: ABS, = Further Options and Accessories = - Spare wheel - Twin tyres = Notes = Müller Mitteltal 2-axle T5 2AL low-bed trailer with ramps Air suspension BPW axles ABS ZSA Tyres 60% GR 235R17.5 ID No. 665 We look forward to welcoming you for consultation, contract signing, or vehicle collection at our dealership. Please make an appointment in advance. If a visit to our dealership is not possible, we offer a complete transaction process by phone, email, WhatsApp, or fax. Upon request, we can deliver your new vehicle directly to your door. This ensures you the best price, maximum security, and convenience when purchasing your vehicle. Trade-in We are happy to accept your used vehicle as a trade-in. We also offer the possibility of a digital vehicle appraisal using your vehicle photos, even without a dealership visit. Our specialised purchasing team guarantees you the highest possible price. Upon request, we can deliver your new pre-owned vehicle nationwide to your doorstep and collect your trade-in vehicle. Financing - Leasing Immediate approval and settlement of existing financing agreements. Your specialised partner for passenger cars, transporters, commercial vehicles, and construction machinery ITC GmbH & Co. KG Kwsdpfx Abexw T Uas Hjw Siemensstraße 7 32312 Lübbecke (Industrial Estate) Visit our website at Constantly over 400 vehicles in stock The details provided in ads, on the internet, price tags, and images are non-binding descriptions and do not constitute guaranteed features. The seller assumes no liability/warranty for typographical or data transmission errors. Listed equipment may need to be checked separately. This offer is generally without new TÜV inspection; we will gladly submit an offer from our partner workshop if required. Subject to errors and prior sale. = Further Information = Unladen weight: 8,900 kg Payload: 26,100 kg gross vehicle weight: 35,000 kg Sale price: €17,999, US$21,180

Stanje: novo, največja dovoljena obremenitev: 8.750 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal KA-TA-R 11.9 Tandem Low-bed Three-way Tipper Trailer with Ramps Reference number for inquiries: 11612 * BRAND-NEW VEHICLE, available immediately, painted in RAL 9016 traffic white * Delivery to your site possible for an additional charge! * Gross weight: 11,900 kg, payload: 8,750 kg * Galvanized floor, 5m x 2.42m x 0.5m; side walls are pendulum-mounted, foldable, and removable; prepared for later fitting of side wall extensions * Bulkhead is hot-dip galvanized * Lockable compartment under the tipping bed for loading ramps * Includes access ramps, 3.31m, 8t pair * 4 UVV lashing rings LC 5000daN at front and rear * 8 lashing eyes LC 3000daN recessed and foldable in the tipper floor (centered) * Net hooks * Drawbar infinitely height-adjustable, hot-dip galvanized, tow eye 40mm * Frame galvanized * Tyres 235/75R 17.5, (4 units), BPW axles, parabolic springs * Tire pressure monitoring Kwjdjyl Ebpopfx Ab Hew * EBS (Electronic Braking System) * LED lighting system for 12+24 volts * Side marker lights with indicator activation * Bolted, galvanized rear stanchions * Excavator bucket rest mounted on the bulkhead ---- Please request an offer from us. Additional equipment available on request. Financing from as little as €405 net/month over 72 months with no down payment and no final balloon payment. Offer provided by our financing partner "FM LeasingPartner". ---- Our business hours: Monday - Thursday: 08:00 - 17:00 Friday: 08:00 - 15:00 Appointments outside opening hours possible by arrangement. WhatsApp Leasing, financing, and trade-in available----

Stanje: novo, največja dovoljena obremenitev: 10.900 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, ETÜ-TA-R 14.4 ----Brake System: * EBS electronic braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Air suspension ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm up to 2,250 mm * 40 mm flange towing eye ----Lighting / Electrical: * TPMS (Tire Pressure Monitoring System) * LED tail lights 12 / 24 V * 15-pin power connector ----General Attachments: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding supports at the rear * Plastic toolbox mounted externally at the front right on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood floor * Preparation in front of the bulkhead for retrofitting container locks * Bolted smooth sheet metal bulkhead * Trapezoidal-profiled, fold-down steel side walls with drop-side spring assists * Steel rear wall, can be stowed between the ramp holders when not in use, inside in front of the bulkhead * Bolted rear stanchions * Rear drive-on slope approx. 860 mm ----Load Securing: * Perforated outer frame, edged at approx. 45 degrees with 2 t lashing capacity every 480 mm * Installation of 3 t fold-down lashing rings possible every 600 mm * 1 x 6.3 t lashing ring at each front and rear corner * Various holes for 1.2 t lashing options in bulkhead and rear crossmember ----Ramps: * One-piece mechanical grating drive-up ramps with spring mechanism for one-man operation, approx. 2,750 x 600 mm (collapsible down to 20 mm) ----Paintwork: Kedpfx Abeq Dyvyo Hjww * Hot-dip galvanized chassis as well as drawbar, bulkhead, rear wall, tailgate, and drive-up ramps * Side wall color in RAL 9010 pure white * Painting of side walls in any RAL color available at extra cost ----Info: * — Reinforced and certified body according to EN 12642 XL including load securing certificate — * New vehicle with manufacturer warranty * Errors and prior sale excepted ----Delivery time: * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 31.900 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release for spring-actuated cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lift/lowering function and RtR valve ----Drawbar: * Straight drawbar with 50 mm towing eye and continuously adjustable height ----Electrics / Lighting: * Tire pressure monitoring system with display option in truck dashboard via EBS signal – no installation required on truck * SmartBoard as infotool with pressure sensors for axle load display per axle group * 15-pin power connector * LED taillights * Removable LED beacon at rear ----General attachments: * Warning plates front & rear * 2 x toolboxes made of galvanized, powder-coated sheet steel approx. 650 x 300 x 600 mm, right side * Closed single plastic mudguards at front * Straight steel spray suppression panels at rear, each with spray suppression Kedpfx Abeylfvmo Hjww * Side underrun protection ----Low-bed platform: * Turntable/platform extension by 520 mm with 45° corners and 3 recessed storage compartments incl. lids and lockable * Flooring on turntable platform made of 50 mm softwood; on low-bed platform made of 60 mm softwood * 20 mm rubber covering instead of timber in drive lane area with a well length of 6,780 mm including sloped ramp * Rubber coating on the ramp left and right, approx. 860 mm length * 4 stake pockets per side (stakes not included) with simultaneous 2 t lashing point capability ----Chassis: * Chassis made of high-strength fine-grain steel ----Load securing (Lasi package): Turntable/platform: * 2 pairs of 13.4 t lashing eyes in outer frame of turntable/platform Low-bed: * 4 pairs of 10 t lashing rings per side on the outer frame, foldable and loadable in all directions * 2 pairs of 13.4 t swiveling lashing rings at rear on each side ----Ramps: * Rubber covering on foldable access ramps * Hydraulic folding ramps with hydraulic tip extension approx. 4,650 x 720 mm * Hydraulically lateral ramp shift & load-holding valves ----Rear support: * Hydraulic rear support ----Widening: * 8 pairs of galvanized folding outriggers for 3 m overall width (not on rear bevel) * Widening boards stowed on left side compartment ----Excavator boom trough: * Excavator boom trough above rear axle to end of slope approx. L=2,100 mm x W=740 x D=190 mm * 2 pairs of 6.4 t lashing rings at sides in excavator trough ----Hydraulics: * Hydraulic flow divider in trailer (for truck hydraulic pump outlet above 40 up to max. 120 ltr./min.) ----Loading dimensions: * Rear loading platform: approx. 6,780 x 2,520 mm (incl. 860 mm ramp) * Platform above turntable: approx. 2,990 x 2,520 mm ----Loading height: * Loaded approx. 890 mm, +/- 20 mm ----Paintwork: * Reflective contour tape at sides and rear * Chassis, turntable, access ramps and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks and turntable painted in black tone ----Info: * New vehicle with manufacturer warranty * Errors and prior sale reserved * Sample images may show special equipment ----Lead time: * Vehicle available from approx. week 23/2026

Stanje: novo, največja dovoljena obremenitev: 13.490 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, TRA-Kombi 18.0: 3-in-1 = for hook-lift containers, skip containers, and as a low loader ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 10.5 t axles ----Suspension: * Air suspension with manual lowering at rear ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm towing eye and height adjustment ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System), display possible in the truck via EBS signal (no truck-side installation required) * LED tail lights 12 / 24 V * 15-pin electrical connector ----General Attachments: * Tool box made of powder-coated sheet steel * Spare wheel holder in basket design on the right side * Closed side underrun protection * Plastic 1/4 mudguards with splash protection * Plastic rear impact bumpers * Foldable "A" sign rear plate ----Loading Area: Kedsl Tld Iopfx Ab Howw * Hot-dip galvanized main frame with raised outer frame for guiding rolling containers * Steel sheet floor with roll recesses in the bogie area * For hook-lift container transport: container length from 5,500 to 7,000 mm possible * Pneumatic 4-point locker and mechanically plug-in front stops in the runway * Transport of up to 2 skip containers with max. 10 m³ volume possible * Includes 8 repositionable container stops for lateral centering, front 4 stops with swiveling shackle * Weld bead as anti-slip surface in the inclined entry area * Mechanical rear landing supports ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning devices for positive and force-fit securing, with 4 cloverleaf-style lashing brackets on each side * 1 pair of 13.4 t UVV lashing rings at the front * On each side, 4 x 8 t lashing eyes recessed into the outer frame ----Ramps: * Aluminium approach ramps (10.6 t / pair), 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable rear storage compartment) ----Paintwork: * Reflective contour tape on sides and rear * Frame hot-dip galvanized * Axles and drawbar painted black ----Info: * Load securing certificate according to DIN 30722-1 * Load securing certificates according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * --Permissible total gross weight technically possible: 20,000 kg-- * New vehicle with factory warranty, no initial registration * Errors and prior sale excepted ----Delivery time: * Available immediately ex Egstorf

Stanje: novo, največja dovoljena obremenitev: 31.900 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, T 4 Profi 40.0 Kwodpfxoylfvgj Ab Hjw ----Brake System: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lifting and lowering system and RtR valve ----Drawbar: * Straight drawbar with 50 mm towing eye and stepless height adjustment ----Electrics / Lighting: * Tire pressure monitoring system with display capability in the truck display via EBS signal – no truck-side installation required * SmartBoard infotool with pressure sensors for axle load display by axle group * 15-pin power connector * LED taillights * Removable rear LED rotating beacon ----General Attachments: * Warning sign package front & rear * 2 x toolboxes made of galvanized (powder-coated) sheet steel, approx. 650 x 300 x 600 mm, mounted right-hand side * Closed single plastic fender at the front * Straight rear steel mudguards with spray protection (anti-spray mist) * Side underrun protection ----Low Loader Deck: * Turntable platform extension by 520 mm with 45° corners and 3 recessed storage compartments including lockable lids * Floor over turntable platform made of 50 mm and on the low loader platform of 60 mm softwood * 20 mm rubber flooring in the running area instead of wooden floor, with a recessed bed length of 6,780 mm including the ramp slope * Rubber flooring on ramp slope left and right, approx. 860 mm long * Four stake pockets per side (stakes not included), each with 2 t lashing capability ----Chassis: * Chassis made of high-strength fine-grained steel ----Load Securing (Lashing Package): Turntable Platform: * 2 pairs of 13.4 t lashing rings on the outer frame of the turntable platform Recessed Bed: * Four pairs of 10 t folding and multi-directional lashing rings per side on the outer frame * Two pairs of 13.4 t swivel lashing rings each at the rear left and right ----Ramps: * Rubber covering on foldable ramps * Hydraulic folding ramps with hydraulically extendable tip, approx. 4,650 x 720 mm * Hydraulic lateral ramp adjustment & load-holding valves ----Rear Support: * Hydraulic rear support ----Widening: * 8 pairs of galvanized folding outriggers for 3 m total width (not at the rear slope) * Widening planks stored in a side compartment on the left ----Dipper Stick Rest: * Dipper stick rest over rear axle to end of ramp slope, approx. L=2,100 mm x W=740 x D=190 mm * 2 pairs of 6.4 t lashing rings on the sides of the dipper stick rest ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump output from the truck over 40 – max. 120 l/min) ----Loading Dimensions: * Rear cargo area: approx. 6,780 x 2,520 mm (incl. 860 mm ramp slope) * Area above turntable: approx. 2,990 x 2,520 mm ----Loading Height: * Loaded approx. 890 mm, +/- 20 mm ----Paintwork: * Reflective contour tape on sides and rear * Chassis, turntable, ramps, and outriggers hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in black ----Info: * New vehicle with manufacturer warranty * Subject to errors and prior sale * Sample images may include special equipment ----Delivery Time: * Vehicle available from approx. week 23/2026

Stanje: novo, največja dovoljena obremenitev: 13.490 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, TRA-Kombi 18.0: * 3-in-1 solution: suitable for roll-off containers, skip containers, and as a low-loader ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 10.5 t axles ----Suspension: * Air suspension with manual lowering at the rear ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long with 40 mm towing eye and height adjustment device ----Electrical / Lighting: * Tire pressure monitoring system (TPMS), display capability in truck via EBS signal (no truck-side installation required) * LED rear lights 12/24 V * 15-pin power connector ----General Attachments: * Tool box made of powder-coated sheet steel * Spare wheel carrier (basket type) on the right side * Closed side underrun protection * Plastic quarter mudguards with splash protection * Plastic rear impact protection buffers * Foldable A-sign at the rear ----Loading Platform: * Hot-dip galvanized main frame with raised outer frame for guiding roll containers * Steel deck with recessed rollers in the bogie area * Can transport roll-off containers with a container length of 5,500 – 7,000 mm * Pneumatic 4-point clamp locking and mechanical plug-in stop angles at the front of the guide track * Transport of up to 2 skip containers with a max. volume of 10 m³ possible * Includes 8 repositionable bin stops for lateral centering of the skips, front 4 stops plug-in with pivoting stop * Weld bead as anti-slip coating in the ramp area of the track * Mechanical drop-down supports at the rear ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the side for securing with tensioning elements, 4 cloverleaf-type lashing brackets per side * 1 pair of 13.4 t UVV lashing rings to the front * 4 x 8 t recessed lashing eyes per side in the outer frame ----Ramps: * Aluminum loading ramps (10.6 t/pair) 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Paintwork: * Reflective contour tape on sides and rear * Frame hot-dip galvanized * Axles and drawbar painted black Kwsdpswb Raksfx Ab Hsw ----Additional Information: * Load securing certificate according to DIN 30722-1 * Load securing certificates according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * --Permissible gross weight of 20,000 kg technically possible-- * New vehicle without initial registration, with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available from Egstorf

Stanje: novo, največja dovoljena obremenitev: 13.490 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, TRA-Kombi 18.0: 3 in 1 = suitable for hooklift containers, skip containers, and as a low-bed trailer ----Braking System: * EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10.5 t axles ----Suspension: * Air suspension with manual rear lowering ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm tow eye and height adjustment device ----Electrical / Lighting: Kwodpfx Ael Tnwzob Hjw * TPMS (Tire Pressure Monitoring System), display capability in the truck via EBS signal (no truck-side installation required) * LED tail lights, 12 / 24 V * 15-pin power connector ----General Attachments: * Tool box made of powder-coated sheet steel * Spare wheel holder, basket design, right side * Enclosed side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear impact protection buffer * Folding A-sign at the rear ----Loading Platform: * Hot-dip galvanized main frame with raised outer frame to guide roll-off containers * Steel sheet floor with roller recesses in the bogie area * When transporting roll-off containers: container length from 5,500 - 7,000 mm possible * Pneumatic 4-point container locking system and mechanically lockable stop angles at the front of the track * Transport of up to 2 skip containers with max. 10 m³ capacity possible * Includes 8 repositionable skip stops for lateral centering, the front 4 are plug-in with pendulum-mounted stops * Weld bead as anti-slip surface in the inclined ramp area * Mechanical rear drop supports ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning elements for positive and non-positive securing of skips, 4 lashing brackets each (shamrock design) on the sides * 1 pair of 13.4 t UVV lashing rings forward * 4 x 8 t lashing eyes recessed in the outer frame on each side ----Ramps: * Aluminum loading ramps (10.6 t / pair) 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Painting: * Reflective contour markings, sides & rear * Frame hot-dip galvanized * Axles, drawbar painted black ----Information: * Load securing certificate according to DIN 30722-1 * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 * --Permissible gross weight of 20,000 kg technically possible-- * New vehicle without initial registration, with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex Egstorf

Stanje: novo, največja dovoljena obremenitev: 10.900 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, ETÜ-TA-R 14.4 ----Braking System: * EBS Electronic Braking System * Emergency release mechanism for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Air suspension ----Tow Bar / Flange Towing Eye: * Height-adjustable tow bar, adjustable by 300 mm * Tow bar extension by 250 mm to a total of 2,250 mm * 40 mm flange towing eye ----Lighting / Electrics: * Tire pressure monitoring system (TPMS) * LED rear lights 12 / 24 V * 15-pin power connector ----General Attachments: * Jost landing gear at the front * Externally mounted hot-dip galvanized folding supports at the rear * Plastic toolbox on the front right side of the headboard * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood floor * Preparation in front of the headboard for retrofitting container locks * Bolted headboard made of smooth sheet metal * Trapezoidal profiled drop-side walls made of steel, foldable with drop-side spring assist * Steel rear wall insertable between ramp mounts; when not in use, stowed inside in front of the headboard * Bolt-on rear posts * Rear approach angle approx. 860 mm ----Load Securing: Kedjpk Dv Repfx Ab Hsww * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Possible installation of 3 t drop lashing rings every 600 mm * One 6.3 t lashing point in each front and rear corner * Various holes in the front and rear cross member for 1.2 t lashing options ----Ramps: * One-piece mechanical grid ramps with spring assistance for single-person operation, approx. 2,750 x 600 mm (can be telescoped down to 20 mm) ----Painting: * Hot-dip galvanized chassis as well as tow bar, headboard, rear wall, tailgate, and ramps * Side wall color RAL 9010 pure white * Painting of side walls in a RAL color of choice available at extra cost ----Information: * --Reinforced and certified body according to EN 12642 XL incl. load securing certificate-- * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Available immediately ex works Egestorf

Stanje: rabljeno, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 02/2021, naslednji pregled (TÜV): 08/2026, dolžina tovornega prostora: 4.800 mm, širina tovornega prostora: 2.430 mm, višina nakladalnega prostora: 500 mm, Oprema: ABS, Müller-Mitteltal nizkopodni kesonski priklopnik - Nizkopodni in dvosmerni kesonski priklopnik v enem vozilu - Vlečno uho 40 mm - Pnevmatski zavorni sistem - Podporna stojala za nakladanje in razkladanje - Gigant osi - Pnevmatske gume: 235/75 R 17,5 Kwedpfx Ajyk Rfkjb Hsw - Bobnaste zavore - Lastna teža: 3.620 kg - Nastavljiva višina drogov - TÜV veljaven do: 08.2026 - SP veljaven do: 02.2026 - SP veljaven do: - Dolžina tovornega prostora: 4.800 mm - Širina tovornega prostora: 2.430 mm - Višina stranic: 0,5 m Pridržujemo si pravico do napak in vmesne prodaje. Interna številka vozila: 11349.