Müller-Mitteltal Eal Prikolice nakup rabljenega (246)

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem equalizing unit * Tire pressure monitoring system with display capability in the truck via EBS signal, no installation required on the truck side * Height-adjustable drawbar (300 mm) with 40 mm flange towing eye * Mechanical landing gear at the front * Rear: 2 mechanical folding support legs * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * 15-pin electrical connector * Multi-chamber tail lamps * Bolted underrun protection * Plastic quarter mudguards * Mesh hooks on the sides and rear in the central locking mounts, plus 2 hooks on the front wall * Main frame made of fine-grain steel * Steel pallet - 2-way tipper body, fixed front wall made of smooth sheet, continuous side walls (foldable without center stanchions, with drop-side spring assist mechanism), pendulum-type operation via manual central locking * Rear stanchions are bolted Bwodjtr Sucopfx Adnow * Steel rear wall slides in front of the ramps * In each corner: 1 x 5 t lashing point; additionally, 4 x 3 t lashing rings each side, integrated into the outer frame * 4 mm floor made of fine-grain steel * Two-piece mechanical grating loading ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (manually retractable to 80 mm) * Chassis, drawbar, rear stanchions, underrun protection, mechanical drop-down supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and landing gear painted in black * Drop sides and platform in RAL 9010 pure white * Painting of side walls and tipping platform in any RAL color available for extra charge * New vehicle with manufacturer's warranty * Subject to prior sale and errors * Available from CW 07/2026

Stanje: rabljeno, skupna masa: 32.000 kg, konfiguracija osi: 2 osi, prva registracija: 01/2014, prostornina tovornega prostora: 10 m³, skupna širina: 2.500 mm, skupna višina: 4.000 mm, Oprema: ABS, For inquiries regarding the vehicle, Mr. Seidel will be happy to assist you (by phone at ...). ----MÜLLER MITTELTAL SF32BM/BT Concrete Mixer Semi-Trailer---- * Superstructure: Liebherr HTM 1004 10m³ * BPW axles * Drum brakes * Spring-loaded brakes * Wabco ABS * 1st axle liftable Bedowipfnepfx Adnoww * Air suspension * Permissible total weight: 32,000 kg * Unladen weight: 6,510 kg * Payload: 25,490 kg * Tire tread depth: 1st axle 14-15 mm, 2nd axle 10 mm Upon request, we can provide you with a leasing or financing offer. Mr. Seidel (phone ...) will be happy to assist you. For more information, please visit our homepage. !!! Subject to errors, changes, and prior sale !!!

Stanje: rabljeno, največja dovoljena obremenitev: 13.750 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 10/2003, dolžina tovornega prostora: 6.600 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 1.000 mm, skupna širina: 2.550 mm, Skupna masa: 18.000 kg Prazna masa: 4.250 kg Nosilnost: 13.750 kg Skupna dolžina: 8.800 mm Dolžina nakladalnega prostora: 6.600 mm Širina: skupna širina 2.550 mm / širina kesona 2.470 mm Višina nakladanja: ca. 1.000 mm Dodatne informacije - 800 mm stranice + zložljiva zadnja vrata - Prednja stena 1.200 mm Bjdpfx Adexnvkfonoww - Zaščita proti naletu - Gigant osi - Dvojna kolesa 235/75R17,5 - Zračno vzmetenje - Zadnji predal za rampe - Hitrospustni ventil - Vodilo za rampe - 4 težki pritrditveni elementi - 6 parov pritrdilnih obročev

Stanje: novo, največja dovoljena obremenitev: 14.300 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 4.995 mm, širina tovornega prostora: 2.380 mm, višina nakladalnega prostora: 900 mm, Oprema: ABS, Müller? Mitteltal KA-TA-R 19 Tandem Tipping Trailer with Bordmatik Left Side Inquiry Number: 11573 * BRAND NEW VEHICLE now finally available for immediate delivery!!! * Delivery free to your premises upon request. * Financing available through our partners FM LeasingPartner or MMV Leasing with terms from 24 to 72 months, with or without down payment, with or without final residual value. * Example: 60 months with no down payment and no residual value – €769 / month * Request your individual quote from us! We are an official Müller Mitteltal dealer. * ---- * Gross weight: 19t, Payload: 14.30t, RAL 9016 traffic white or custom paintwork upon request * Reinforced and certified body built to EN 12642 XL including load securing certificate * Body – Steel 4,995mm x 2,380mm x 900mm * Right side with spring-assisted steel tailgate (2 springs), rear wall steel * Left side with Müller Bordmatic hydraulic sideboard (Bordmatik) * Removable roll tarpaulin for tipper * 4 pairs of lashing rings, recessed and foldable in 5mm steel floor, LC 3000 daN * LED lighting system 12+24 Volt replacing standard lighting * 2 LED reversing lights * Side marker lights with indicator function * BPW Eco axles, air suspension, drum brakes * 385/65R 22.5 tyres, with TPMS, EBS 2S/2M * 4 semi-round mudguards * Chassis, drawbar and foldable rear underrun protection hot-dip galvanized * Front wall platform with galvanized access step * Drawbar with 50mm eye, adjustable by +77mm / +33mm * Front support leg with crank * Foldable underrun protection for paver feeding * Removable protective grille for tail lights * ---- * Our business hours * Monday – Thursday: 08:00 – 17:00 Bwodpfx Adjwq Uihenew * Friday: 08:00 – 15:00 * Outside business hours, appointments available by arrangement * We speak German, English, Russian, Polish, French * Leasing, financing, trade-in possible

Stanje: rabljeno, lastna masa: 3.450 kg, največja dovoljena obremenitev: 14.550 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 05/2010, naslednji pregled (TÜV): 07/2025, vzmetenje: zrak, velikost pnevmatike: 235/75R17.5, barva: rumena, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Vehicle location: Bovenden, 2 axles, turntable trailer, air suspension, ABS (anti-lock braking system), container locking mechanism, underrun protection, side aluminum side guard, twin tires. Body: 2-axle outer roller trailer for roll-off containers from 5.5 m to 7 m or 2x 10 m³ skip containers, BPW axles, drum brakes, pneumatic locking, pneumatic lowering drawbar. ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale, and errors! Bjdpfxjxgilme Adnoww

Stanje: rabljeno, skupna masa: 47.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2004, naslednji pregled (TÜV): 08/2026, * Müller Mitteltal TS3 nizkopodni polpriklopnik * Prva registracija: 11/2004 * 3 osi * Zračno vzmetenje Bwodpfx Adjw Tgkbsnew * Gigant osi * Hidravlične dolge rampe, pomične in zložljive * Razširitve iz 2,50 m na 3,0 m širina nakladalnega prostora * Nakladalna dolžina: 8,50 m pri nakladalni višini 0,85 m * Nakladalna dolžina na vratu: 3,40 m pri nakladalni višini 1,50 m * Podpore * Neto teža: 10.260 kg * Tehnično dovoljena skupna masa: 47.000 kg * TÜV veljaven do: 08/2026 * Tehnični pregled do: 02/2026

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 2 x 7 ton Gigant axles * Parabolic springs with tandem compensation unit * Tire pressure monitoring with display capability in the truck via EBS signal, no installation required on truck side * Height-adjustable drawbar (300 mm) with 40 mm flange towing eye * Mechanical support winch at the front * Rear: 2 mechanical foldable supports Bwjdpetr St Uefx Adnow * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * 15-pin electrical connector * Multi-chamber tail lights * Bolt-on underrun protection * Plastic quarter mudguards * Net hooks on sides and rear, integrated in the central locking bearings, plus 2 units on the front wall * Main frame made of fine-grain steel * Steel pallet 2-way tipper body with fixed smooth sheet front wall, continuous foldable side walls (without center stanchions, with sideboard spring lifters and manual central locking for swinging function) * Removable screw-on rear stanchions * Steel rear wall mounted in front of the ramps * In each corner: 1 x 5 ton lashing point; in each side: 4 x 3 ton lashing rings integrated into the outer frame * 4 mm floor made of fine-grain steel * Two-part mechanical grating loading ramps with aluminum tapered end, 2,150 + 1,300 mm x 600 mm (retractable to 80 mm manually) * Chassis, drawbar, rear stanchions, underrun protection, mechanical supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and support winch painted in black tone * Side boards and platform in pure white, RAL 9010 * Painting of side walls and tipper platform in any RAL color available at additional cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from calendar week 07/2026

Stanje: rabljeno, največja dovoljena obremenitev: 10.550 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, prva registracija: 03/2024, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.500 mm, skupna širina: 2.550 mm, skupna višina: 3.100 mm, Müller Mitteltal Low Loader Trailer ---- New low loader from Müller Mitteltal, extensive special equipment. * Hot-dip galvanized * Wooden floor * Side marker lights with indicator activation * LED lighting system * Platform design, 400 mm * Platform extension up to 7,000 mm * Increased to 14,000 kg gross vehicle weight * Air suspension 17.5'' (BPW) incl. EBS / connector * Lifting and lowering with WABCO TASC RtR valve Bwedpfx Adswd Sx Honjw * ALU compressed air tanks * Swiveling towing eye 40/50 mm for tandem trailer (coupling height 56 mm with 40 mm eyelet due to height offset) * 4 Twist Lock container locks * 14 UVV lashing rings * 2 stainless steel toolboxes 350 mm x 320 mm * Ramps made of ALU with tapered section / two-piece 2150 mm + 1300 mm x 600 mm / minimum internal spacing 80 mm! * 2 LED work lights * 2 LED reversing lights ----* Whatsapp: You are welcome to contact us via Whatsapp; we can send you more pictures and a video there. * Export: Would you like to purchase the vehicle outside the EU? We can prepare all necessary customs documents for you. International customers from all over the world are welcome! Net sales are only possible with a 19% security deposit. * Viewing: Please always arrange an appointment with us to view the vehicle. * Note: The information provided here does not represent a guaranteed specification. The details in the purchase contract are decisive. Subject to errors and changes in equipment. * You are also welcome to contact us in English. ?..professional vehicle trading since 2009!

Stanje: rabljeno, lastna masa: 4.120 kg, največja dovoljena obremenitev: 13.880 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 03/2016, naslednji pregled (TÜV): 02/2026, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.360 mm, višina nakladalnega prostora: 900 mm, prostornina tovornega prostora: 10 m³, vzmetenje: zrak, velikost pnevmatike: 385/65R22.5, barva: rdeča, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Lokacija vozila: Bovenden, 2 osi, BPW osi, tandem, zračno vzmetenje, ABS (sistem proti blokiranju koles), zaščita proti podvozu, prednja opora, nihajna vrata. Nadgradnja: Tandemska prekucna prikolica z aluminijastimi stranicami, cca 10 m³, 2x 9t BPW osi, bobnaste zavore! Višina nakladanja cca 1510 mm! PODATKI O DODATNI OPREMI BREZ GARANCIJE, spremembe, vmesna prodaja in napake pridržane! Bwodpfx Aoxfli Ejdnow

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-ER 14.4 Platform: * TPMS (Tire Pressure Monitoring System) * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes Bjdev D Tbdepfx Adneww * 2 x 7-ton BPW axles * Air suspension with lifting and lowering system * Mechanically adjustable 3-meter warning panel sets, front and rear * Drawbar adjustable in height by 300 mm with 40 mm flange eye * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (thus B-dimension approx. 8,080 mm) * Landing gear/winch at the front * External foldable rear support legs * Plastic toolboxes approx. 750 x 350 x 300 mm each, on left and right sides * Side underrun protection * Rear underrun protection * Plastic quarter mudguards * 15-pin power plug * LED lighting system, 12 / 24 V * 2 additional LED reversing spotlights at the rear (wired via reverse gear) * 1 removable LED beacon (incl. bracket) at the rear * 400 mm high bolted front wall * 50 mm softwood flooring * 2 pairs of container locks (extendable to 3 m exterior container width) and lockable; locking dimension retracted according to ISO-DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not DIN-compliant) with a total exterior width of 3,000 mm * Perforated outer frame, approx. 45 degree angled, with 2 t lashing capacity every 480 mm, possible installation of 3 t folding lashing brackets every 600 mm – on each side, 5 x 3 t UVV lashing brackets installed –, at each front and rear corner 1 x 6.3 t lashing ring (front directly behind the container locks in the wooden floor and rear in the end crossmember), various holes for 1.2 t lashing options in the front wall and end crossmember * 1 pair of aluminum insert ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tired and tracked vehicles * Rear storage compartment integrated below the loading area in the chassis * ---Chassis, drawbar, front wall, underrun protection, and rear supports hot-dip galvanized--- * Axles, air tanks, front landing gear, and flange eye painted in black * New vehicle with manufacturer warranty * Subject to errors and prior sale * Available from week 09/2026

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tyre pressure monitoring system * Emergency release unit for spring-actuated brake cylinders Bjdpfxel Tik Ns Adnoww * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting/lowering system and RtR valve * Smard on-board weight measurement system * Warning sign packages front & rear * Reflective contour tape on sides and rear * Removable rotating beacon at the rear * LED lighting * Straight drawbar with 50 mm towing eye and infinitely height-adjustable * Tool box made of powder-coated steel sheet and basket-type spare wheel holder, right-hand side * Front closed individual plastic fenders * Rear straight steel spray guards with spray suppression * Lateral underrun protection * Turntable platform front extension by 520 mm with 45° corners and 3 recessed lockable storage compartments incl. covers * Chassis made of high-strength fine-grained steel * Turntable platform floor made of 50 mm and low-bed platform of 60 mm softwood * Outer planks of the drive-on ramps made of hardwood * Four stake pockets per side (stakes not included) and 2 t lashing point each * Lashing package comprising: Two 6.4 t lashing rings front left & right on the main frame of the turntable platform * Two pairs 13.4 t lashing rings at outer frame, front and rear, and four pairs per side 10 t lashing rings, swivel and height adjustable * Loadable in all directions and recessed into the outer frame * Two pairs 6.4 t lashing rings in the excavator arm rest area * Eight pairs galvanized folding outriggers for 3 m overall width (not in rear slope area) * Extension boards stored in a compartment on the left side * Excavator arm rest area above rear axle up to end of access ramp approx. 2,100 x 740 x 190 mm * Mechanical rear drop-down supports * Hydraulic folding ramps with hydraulically extendable ramp tips approx. 4,650 x 720 mm incl. hydraulic side-shifting ramps & load-holding valve * Deck area above slewing ring: approx. 2,990 x 2,520 mm * Rear load area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, turntable, drive-on ramps, folding outriggers, and mechanical drop-down supports hot-dip galvanized * Axles, drawbar, air tank, and slewing ring painted black * Tyres 235/75 R 17.5 * New vehicle without first registration, with manufacturer warranty * Subject to errors and prior sale * Available from CW 07/2025

Stanje: novo, največja dovoljena obremenitev: 20.200 kg, skupna masa: 27.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TR 27.0 flatbed: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lifting and lowering function and RTR feature * 1st axle liftable * Last axle as trailing steering axle with electro-pneumatic steering lock triggered via reverse gear pin (lock of the trailing axle from the towing vehicle for shunting purposes – no truck-side installation required – assigned to PIN 10 in the 15-pin connector, for shunting only, not for public road traffic) * SmartBoard control box as information tool with pressure sensors for total axle load indication * Tire pressure monitoring with display option in the truck via EBS signal, no truck-side installation required * Fixed center drawbar with 50 mm flange eye (loaded 900 mm, mm height adjustment at the head plate) * Mechanical landing gear at the front, mechanical swing-down supports at the rear of the chassis * Hydraulic flow divider * Continuous side walls (without center stanchion) up to the loading slope * Foldable rear stanchions * Steel tailboard inserted in front of the rear stanchions * Mechanically adjustable warning sign package front and rear * Toolboxes made of galvanized sheet steel - black powder-coated - approx. 650 x 300 x 600 mm, mounted on the right side * 15-pin power connector * LED taillights * Removable LED beacon including bracket and installation * 2 x LED reversing lights at the rear of the vehicle (switched via reverse gear) * Flashing LED side marker lights * 60 mm larch/Douglas fir timber floor * 400 mm plug-in steel front wall * Perforated outer frame, bent approx. 45 degrees with fixture for mounting 3 t folding lashing rings * In each corner: 1 x 10 t lashing ring; additionally, 2 x 10 t and 3 x 6.3 t lashing rings on each side * Various boreholes in front and end beams for 1.2 t lashing options * Hydraulic one-piece loading ramps, approx. 3,000 x 720 mm, mechanically adjustable sideways * 4-way hydraulic control block for optional retrofitting of hydraulic ramp shift * Chassis, drawbar, front wall, mechanical rear supports, loading ramps hot-dip galvanized * Axles, air tanks, flange eye and front landing gear painted in black tone Bwjdpsr Dpzxsfx Adnow * Hydraulic flow divider in the trailer (for hydraulic pump output in the truck over 40 l/min up to 120 l/min) * New vehicle with manufacturer warranty * Errors and prior sale excepted * Available from week 13/2026 * Sample images

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic brake system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting/lowering system and RtR valve * Smard-Board for load weight determination * Warning sign packages at the front & rear * Reflective contour tape on the sides and rear * Removable rear rotating beacon * LED lighting Bodpfx Ajl Tphrsdnsww * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated sheet steel and spare wheel holder in basket design on right side * Front: closed single plastic mudguards * Rear: straight steel mud flaps with spray suppression * Side underrun protection * Turntable platform extended by 520 mm at the front, with 45° corners and 3 recessed, lockable storage compartments with lids * Chassis made of high-strength fine-grain steel * Decking over turntable platform made of 50 mm, and in low-bed platform of 60 mm coniferous timber * Outer planks of ramps made of hardwood * 4 stake pockets on each side (no stakes provided) with simultaneous 2 t lashing capability * Load securing package includes: 2 lashing eyes, 6.4 t, at the front left and right on the main frame of the turntable platform * On each side front and rear: 2 pairs of 13.4 t lashing rings on the outer frame and on each side 4 pairs of swiveling and lowerable 10 t lashing rings * Loadable in all directions, recessed into the outer frame * 2 pairs of 6.4 t lashing rings on the side in excavator arm recess * 8 pairs of galvanized folding outriggers for 3 m total width (not at the rear slope) * Widening planks stored in a side compartment on the left * Excavator arm recess over the rear axle to end of rear slope approx. 2,100 x 740 x 190 mm * Mechanical drop supports at rear * Hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm including hydraulic sideways ramp adjustment & load-holding valve * Loading deck over turntable: approx. 2,990 x 2,520 mm * Rear loading deck: approx. 6,780 x 2,520 mm * Load height loaded approx. 890 mm, +/- 20 mm (including 860 mm rear slope) * Flow divider installed * Chassis, turntable, loading ramps, folding outriggers, and mechanical drop supports hot-dip galvanized * Axles, drawbar, air reservoirs, and turntable painted in black * Tires: 235/75 R 17.5 * New vehicle, not previously registered, with manufacturer’s warranty * Errors and prior sale reserved * Available from CW 07/2026

Stanje: novo, največja dovoljena obremenitev: 13.350 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 4.995 mm, širina tovornega prostora: 2.380 mm, višina nakladalnega prostora: 900 mm, prostornina tovornega prostora: 11 m³, Leto izdelave: 2026, * Wabco EBS-E (electronic braking system with RSS) * Emergency release unit for spring-actuated cylinders * Drum brakes * Tire pressure monitoring system with display capability in truck dashboard via EBS signal – without installation on truck * 2 x 9 t Gigant axles * Air suspension with level control during tipping operation * Drawbar with 50 mm flange eye (adjustable by +77 mm and -33 mm via offset plate) * Jost landing gear at front Bwedpfxoxl Nkgj Adnjw * Foldable, galvanized steel underride guard for paver feeding * Enclosed plastic single fenders * Standing platform on front wall * Manual roll tarp * 15-pin power connector * LED tail lights with galvanized protective hood * Chassis made of fine-grained steel * Steel three-way tipper body (side walls with MM-profile – continuous without center stanchion – swinging via manual central locking and foldable with drop-side spring lifters) * Roll tarp similar to RAL 7038 agate grey, with tarpaulin tensioning using ratchet straps at the sides and tensioning rubbers at front and rear * Front wall platform made from grating with access step on drawbar and grab handle on front wall * Rear wall – made of HBW 400 steel – swinging via automatic 2-claw lock * 5 mm steel floor made of HBW 450 steel * Four recessed and foldable 3 t lashing rings per side – embedded in steel floor * Reinforced and certified superstructure according to EN 12642 XL incl. load securing certificate up to 19 t * Tipping platform and side walls in RAL 9010 pure white * Painting of drop sides in RAL 9010 pure white * Painting of side walls in a RAL color shade available at extra charge * Chassis painted in RAL 9011 graphite black * New vehicle with full manufacturer’s warranty * Subject to errors and prior sale * Available from calendar week 11/2026 * Sample images

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2025, * TS 3 Profile 30.0: * Wabco EBS-E (electronic braking system) * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco Plus axles * Air suspension with lift and lower system and RtR valve * Rear axle is self-steering with electro-pneumatic steering lock * Smartboard control box mounted as an information tool on the trailer, equipped with pressure sensors for total axle load display * Side underrun protection * Landing gears at front and rear with mechanical swing-down supports on the chassis * 15-pin electrical connector * LED lighting system 12/24V * Removable LED beacon on the rear left * Mechanically adjustable warning sign packages front and rear * Straight steel plate mudguards * Spare wheel holder on the right side under the chassis * Fifth wheel platform with 45° chamfered front corners and front-mounted toolbox made of galvanized steel (W = 2,480 x H = 500 x L = 665 mm) with folding lid * 400mm high aluminum side boards (RAL 9010 pure white), foldable and removable, on the fifth wheel platform * Rear wall – 150 mm – inserted high * Rear slope on the fifth wheel platform to low bed approx. 700 mm long * Fifth wheel platform with 50 mm wooden planks and low bed platform with 60 mm wooden planks * Tread plate over the axles Bwjdpfx Ael Tnvgsdnow * 8 x mechanical folding widenings to a total width of 3 meters, not at the rear slope (widening planks included, stored on the fifth wheel platform) * Load securing package: on the fifth wheel platform 2 x 6.3 t lashing rings per side, and 3 x 5 t lashing bars per side in the outer frame, in the low-bed platform per side 2 x 13.4 t lashing rings and 4 x 10 t folding/retractable lashing rings recessed in the outer frame, 2 x 6.4 t lashing eyes per side and 1 lashing ring in the excavator arm recess at the rear * Continuous excavator arm recess from the end of the last rigid axle over the steering axle to the end cross member, with internal reinforcement profiles (approx. L = 2,450 x W = 770 mm x D = 270 mm) * 2 x container locks directly after the neck in the low bed platform * Mechanically single-piece, hot-dip galvanized hydraulic loading ramps approx. 3,000 x 720 mm (mechanically adjustable laterally) * 4-way control block for future customer-side retrofit of hydraulic ramp shift * The outer board on the loading ramp is made of 50 mm hardwood * Hydraulic flow divider in the trailer (for truck hydraulic pump capacity from 40 l/min up to 120 l/min) * Loading area of the fifth wheel platform: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Unladen loading height approx. 910 mm (including 860 mm approach slope) * Saddle height approx. 1,220 mm (suitable for 2- and 3-axle tractors) * Chassis, ramps, rear folding supports, widening consoles hot-dip galvanized * Axles, landing gears, air tanks painted in a black tone * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Errors and prior sale excepted * Available from week 16/2026

Stanje: novo, največja dovoljena obremenitev: 20.200 kg, skupna masa: 27.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TR 27.0 platform: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lifting and lowering system including RTR function * 1st axle liftable * Rear axle as trailing steering axle with electro-pneumatic steering lock activated by reverse gear pin (steering lock for the trailing axle from the tractor, for shunting purposes only—no installation required on the truck—assigned to pin 10 in the 15-pin connector, for shunting only, not permitted for public road use) * SmartBoard control unit as an infotool with pressure sensors for total axle load display * Tire pressure monitoring with display in the truck via EBS signal, no truck-side installation required * Fixed central drawbar with 50 mm flange eye (loaded: 900 mm, adjustable height at the head plate) * Mechanical landing gear at the front, mechanical swing-down supports at the rear of the chassis * Mechanically adjustable warning sign package at front and rear * Toolbox made of galvanized steel sheet—black powder coated—approx. 650 x 300 x 600 mm, right side * Hydraulic flow divider * Continuous sidewalls (without center stake) up to the drive-on slope * Folding rear stanchions * Steel rear wall slid in front of the rear stanchions * 15-pin electrical connector * LED tail lights * Removable LED beacon, including bracket and installation * 2 x LED reversing lights at vehicle rear (actuated by reverse gear) * Flashing LED side marker lights * 60 mm larch/douglas fir wooden floor * 400 mm plug-in steel front wall * Perforated outer frame, approx. 45° angled, with provisions for mounting 3 t folding lashing brackets * One 10 t lashing ring in each corner, plus two 10 t and three 6.3 t lashing rings per side * Various holes in front and rear crossmembers for 1.2 t lashing possibilities * Hydraulic one-piece drive-on ramps, approx. 3,000 x 720 mm, mechanically adjustable sideways * 4-bank hydraulic control valve for possible retrofitting of hydraulic ramp shift * Chassis, drawbar, front wall, rear mechanical supports, drive-on ramps, and tailgate hot-dip galvanized * Axles, air tanks, flange drawbar eye, and front landing gear painted in black Bwedpfx Adjr Dpz Asnew * Hydraulic flow divider in trailer (for hydraulic pump output in the truck above 40 l/min up to 120 l/min) * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from week 13/2026 * Sample images

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: * Wabco EBS-E (electronic braking system) * RDÜ (tire pressure monitoring system) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco Plus axles * Air suspension with lift and lower function, as well as RtR valve * Last axle steering with electro-pneumatic steering lock * Smartboard control box mounted on the trailer as info tool with pressure sensors for total axle load display * Side underrun protection * Landing gear at front and mechanical swing-down supports at rear of chassis * 15-pin power connector * LED lighting system 12/24V * LED rotating beacon (removable) at rear left * Mechanically adjustable warning sign packages front and rear * Straight steel mudguards * Spare wheel holder underneath chassis, right side * Fifth wheel platform with 45° chamfered front corners and front tool box made of galvanized sheet steel, W = 2,480 x H = 500 x L = 665 mm with folding lid * Side of the fifth wheel platform equipped with 400 mm high aluminium drop-side boards (RAL 9010 pure white), foldable and removable * Removable rear wall – 150 mm high * Rear ramp on fifth wheel platform to lowbed, approx. 700 mm long * Fifth wheel platform fitted with 50 mm timber planks, lowbed platform with 60 mm timber planks * Chequer plate above the axles * 8 x mechanical foldable extensions to 3 m overall width (excluding rear ramp area), extension planks available with storage platform * Lashing package: On the fifth wheel platform, 2 x 6.3 t lashing rings each and 3 x 5 t lashing bars per side on the outer frame; on the lowbed platform, 2 x 13.4 t lashing rings per side plus 4 x 10 t lashing rings, pivotable and lowerable, fitted in the outer frame; 2 x 6.4 t lashing eyes per side plus 1 lashing ring in the excavator stick recess at rear * Excavator stick recess, running continuously from end of last fixed axle over the steering axle to the closing crossmember, with internal reinforcement profile, approx. L = 2,450 x W = 770 x D = 270 mm * 2 x container locks directly after the step in the lowbed platform * Mechanically operated one-piece hot-dip galvanized hydraulic ramps, approx. 3,000 x 720 mm (mechanically adjustable in width) * 4-way control block for later customer retrofitting of hydraulic ramp displacement * Outer board on ramp made of 50 mm hardwood * Hydraulic flow divider in the trailer (for truck hydraulic pump output from over 40 l/min up to 120 l/min) * Loading area of fifth wheel platform: approx. 3,935 x 2,480 mm * Lowbed loading area: approx. 8,500 x 2,520 mm * Loading height unladen approx. 910 mm (including 860 mm drive-on ramp) * Fifth wheel height approx. 1,220 mm (suitable for 2- and 3-axle tractor units) * Chassis, ramps, rear folding supports, widening consoles hot-dip galvanized * Axles, landing gear, air tanks painted in black Bodpfjpk D I Aox Adneww * Hydraulic flow divider * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from week 16/2026

Stanje: novo, največja dovoljena obremenitev: 37.390 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2025, * TS 3 RM ML 30.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 t BPW axles * Air suspension with lifting and lowering function as well as RtR valve * Traction aid for shunting purposes switched to the first axle via EBS (no installation required on the truck side) * Smart-Board mounted as an information tool on the trailer with pressure sensors for total axle load display * Last axle as self-steering axle with electro-pneumatic steering lock * Steering lock for self-steering axle can be activated from the driver's cab for shunting purposes via EBS (no installation required on the truck side) * 2nd king pin position 2 Bjdpfsq Euakox Adnjww * Side underrun protection, landing gear at the front and swinging support legs at the rear of the chassis * 15-pin electrical connector * LED lighting 12/24 V * LED beacon (removable) at rear * 2 additional LED reversing lights * 7-pin socket at the rear for oversized load lighting * Side marker lights with indicator control * Tire pressure monitoring with display option in the truck via EBS signal (no installation required on the truck side) * Mechanically adjustable warning plate packages at front and rear * Straight steel sheet mudguards * Spare wheel holder in front of the bulkhead cross member (without spare wheel) * Gooseneck platform with 45° chamfered front corners and front toolbox made of galvanized, powder-coated steel sheet, W=2,480 x H=500 x L=665 mm, with hinged lid * 400 mm drop-side aluminum boards on the sides of the gooseneck platform (RAL color of choice), foldable and removable * Rear wall inserted at 150 mm height * Rear slope on the gooseneck platform to the lowbed approx. 700 mm long with checker plate covering; hole strip at the end for hooking in aluminum drive-on ramps * Gooseneck platform with 50 mm clamped wooden planks and lowbed platform with 60 mm clamped wooden planks * Tear plate over the axles * 9x manual fold-out extensions up to 3 m total width, but not in rear slope (extending boards present with closed storage box fitted transverse to the direction of travel under the loading area) * 3 mounting shafts under the gooseneck platform for storage of optional aluminum ramps or wooden planks for wheel well covering * Pivoting arm as a carrier for connection lines from the truck to the trailer * Load securing package consisting of: gooseneck platform with perforated outer frame, 45° angled, hole pattern for lashing devices (2 t lashing capacity per lashing point with minimum spacing of 480 mm) * Each side with 3 x 13.4 t recessed lashing rings in the floor (1x on the gooseneck platform, 1x on longitudinal frame after camber, 1x over the center axle next to the longitudinal frame) * Each side with 3 x 13.4 t lashing rings on outer frame (1x start of gooseneck camber, 1x beginning of ramp, 1x end of ramp) * Each side with 2 x 10 t lashing rings (1x between front wheel well and first axle, 1x between second and third axle) * Each side with 3 x 5 t lashing rings bolted to the outer frames of the wheel wells (2 on the front, 1 on the rear wheel well) * Extended excavator boom trough from end of last rigid axle over steering axle to the end cross member, continuously with internal reinforcement profile approx. W=770 mm x Depth rear=270 mm / Depth front=170 mm, each side with 2 x 6.4 t lashing rings in the excavator boom trough * Each side with 2 wheel wells, 390 mm deep and 640 mm wide, for transporting wheel loaders with a

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2025, * T3 Profile 30.0: * EBS brake system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical rear axle equalization * Side underrun protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning signs front and rear * Front closed plastic mudguards and rear straight galvanized steel skirts, each with splash protection * Reflective contour markings on the sides and rear * Hinged lid (hot-dip galvanized) for toolbox on the turntable platform * Multi-voltage system * LED tail lights * Removable revolving beacon at the rear * Drawbar with 40 mm towing eye, height adjustment via tension spring and turnbuckle * 15-pin electrical connector * Four stake pockets per side (stakes not included) with additional lashing points Bwsdpfx Ael Thxdodnjw * Load securing package comprising: 2 lashing eyes (6.4 t) front left & right on the main frame of the turntable platform, 5 pairs of UVV-compliant drop-down and swiveling lashing rings, loadable in all directions and recessed into the outer frame – load capacity in corners 13.4 t, otherwise 10 t * 6 pairs of mechanical fold-out outriggers for 3-meter total width (not in the rear taper) * Widening planks stored in the center of the loading area * Excavator arm trough above rear axle up to the end crossmember, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings at the sides in the excavator trough) * Hydraulically operated one-piece loading ramps (approx. 3,000 x 720 mm), laterally adjustable * Loading area above the turntable: approx. 1,960 x 2,520 mm * Unladen loading height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height approx. 910 mm (incl. 860 mm drive-on slope) * Chassis, turntable, drawbar and ramps hot-dip galvanized * Axles, springs, air tanks etc. painted in black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * --technically permissible total weight 30,000 kg-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Available from CW 38/2025

Stanje: novo, največja dovoljena obremenitev: 37.390 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2025, * TS 3 RM ML 30.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW axles * Air suspension with lift and lower system, including RtR valve * Hill-hold assist for maneuvering, switchable to the first axle via EBS (no truck-side installation required) * SmartBoard as an infotool mounted on the trailer with pressure sensors for total axle load display * Last axle as trailing steering axle with electro-pneumatic steering lock * Lock for the trailing axle actuated from the cab for maneuvering purposes via EBS (no truck-side installation required) * Second king pin position 2 Bwodetpta Dopfx Adnow * Side underrun protection, landing legs at the front and swing-down support legs at the rear of the chassis * 15-pin electrical socket * LED lighting 12/24 V * Removable LED beacon at the rear * 2 additional LED reversing lights * 7-pin socket at the rear for overlength lighting * Side marker lights with indicator control * Tire pressure monitoring with display possibility in the truck via EBS signal (no truck-side installation required) * Mechanically adjustable warning panel kits at the front and rear * Straight steel mudguards * Spare wheel holder in front of the front wall crossmember (without spare wheel) * Fifth-wheel platform with 45° chamfered front corners and a front-mounted toolbox made of galvanized, powder-coated sheet steel, B = 2,480 x H = 500 x L = 665 mm, with hinged lid * On the side of the fifth-wheel platform, 400 mm aluminum drop and removable side walls (in RAL color of choice) * Rear wall – inserted to 150 mm height * Rear slope on the fifth-wheel platform to the lowbed approx. 700 mm long with checker plate covering, and a perforated strip at the end for attaching aluminum drive-on ramps * Fifth-wheel platform with 50 mm clamped wood planks, and low-bed platform with 60 mm clamped wood planks * Tear plate above the axles * 9 x mechanical folding extensions for an overall width of 3 meters, but not on the rear slope (extension boards available with transverse closed storage compartment beneath the loading area) * 3 storage compartments under the fifth-wheel platform for optional aluminum drive-on ramps or wooden planks for covering wheel recesses * Swivel arm as carrier for connection lines from the truck to the trailer * Load securing package includes: on the fifth-wheel platform, perforated outer frame with 45° angled profile, with hole pattern for lashing equipment (2 t lashing force per lashing point at a minimum spacing of 480 mm) * On each side, 3 x 13.4 t recessed lashing rings in the floor (1 on the fifth-wheel platform, 1 on the longitudinal beam after the gooseneck, and 1 over the middle axle next to the longitudinal beam) * On each side, 3 x 13.4 t lashing rings on the outer frame (1 at the start of the fifth-wheel platform gooseneck, 1 at the start of the ramp, 1 at the end of the ramp) * On each side, 2 x 10 t lashing rings (1 between the front wheel recess and first axle, 1 between the second and third axles) * On each side, 3 x 5 t lashing rings bolted to the outer frames of the wheel recesses (2 at the front and 1 at the rear wheel recess) * Extended excavator arm trough, continuously from the end of the last rigid axle over the steering axle up to the rear, with internal reinforcement profile approx. W = 770 mm, rear depth = 270 mm / front depth 170 mm, on each side 2 x 6.4 t lashing rings in the excavator arm trough * On each side, 2 wheel recesses, 390 m

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2025, * T3 Profile 30.0: * EBS brake system * RDÜ tire pressure monitoring * Emergency release system for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic leaf springs * Mechanical rear axle equalization * Side underrun protection * Swing-down supports at the rear of the chassis frame * Mechanically adjustable front and rear warning sign packages * Front plastic mudguards (closed) and straight, galvanized steel rear mudflaps, each with splash protection * Reflective contour marking strips on the sides and rear * Hinged (hot-dip galvanized) lid for tool box located on the turntable platform * Multi-voltage electrical system * LED rear lights Bsdpfx Aol Thxaodnsww * Removable beacon at the rear * Drawbar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin electrical plug * 4 stake pockets per side (stakes not included), each with simultaneous lashing facility * Load securing package comprising: 2 lashing eyes (6.4 t) front left & right on main frame of turntable platform, 5 pairs of UVV lashing rings, swiveling and lowerable, loadable in all directions and recessed into the outer frame – corners rated to 13.4 t, otherwise 10 t. * 6 pairs of mechanical swing-out supports for 3 m overall width (not at rear slope) * Widening planks stored in the center of the loading area * Excavator arm rest over rear axle up to end buffer, approx. 2,100 mm long (2 pairs of 6.4 t lashing eyes at the side in the excavator arm rest) * Hydraulic one-piece drive-on ramps (approx. 3,000 x 720 mm), lateral adjustment * Loading area above turntable: approx. 1,960 x 2,520 mm * Unladen loading height: approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height: approx. 910 mm (incl. 860 mm approach angle) * Chassis, turntable, drawbar and drive-on ramps hot-dip galvanized * Axles, springs, air tanks etc. painted in black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * --Permissible gross weight of 30,000 kg technically possible-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Subject to errors and prior sale * Available from week 38/2025

Stanje: novo, največja dovoljena obremenitev: 5.840 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2025, * KWH 8.8 ML: * TPMS (Tire Pressure Monitoring System) * EBS braking system * Drum brakes * BPW axle * Parabolic springs * Support winch at the front * Spring-assisted square tube support legs at the rear with base plates and safety lock pins for various support heights * Drawbar with 40 mm bolt coupling (height-adjustable) * 15-pin electrical connector * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and cross members * Enclosed steel fenders with splash guards * Closed side underrun protection, usable as advertising space * Plastic toolbox with base insert (installed horizontally), approx. 500 x 350 x 400 mm * Swiveling cable drum assembly, clear width between the drum arms 1,700 mm, with tension lock for fixing the drum at the support arm ends, as well as a central claw lock for securing the cable drum assembly to the chassis * Motor-hydraulic drum drive with oil motor * Valves and adjustable drive rollers with rubber lining * Hydraulic speed regulator and brake for the drum drive * Steel drum shaft, 76 mm in diameter, with centering and rotating ends Bodpfx Adju I Iqxjnsww * 1 pair of stepped centering cones made of polyamide * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) * Finish: hot-dip galvanized * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 5.840 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2025, * KWH 8.8 ML: * RDÜ Tire Pressure Monitoring * EBS Brake System * Drum Brakes * BPW Axle * Parabolic Springs * Front Support Winch Bedpfx Aeu I Iqljdnsww * Rear Square Tube Support Legs with Spring Assistance, Base Plate, and Safety Locking Pins for Adjustable Support Heights * Drawbar with 40 mm Bolt-on Eye (height adjustable, __ mm) * 15-pin Electrical Connector * LED Lighting * Flashing LED Side Marker Lights * Chassis made of torsion-resistant square tubes and cross beams * Enclosed steel mudguards with splash protection * Enclosed lateral underrun protection usable as advertising space * Plastic toolbox with floor insert (installed horizontally), approx. 500 x 350 x 400 mm * Swiveling cable drum carrier, clear width between drum arms 1,700 mm, with tension fastener for securing the drum to the carrier arms and a central pawl lock for securing the cable drum carrier to the chassis * Motor-hydraulic drum drive with oil motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft diameter 76 mm, with centering and rotating ends * 1 Pair of stepped Polyamide Centering Cones * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) * Finish: Hot-dip galvanized * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 5.840 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2025, * KWH 8.8 ML: * TPMS (Tire Pressure Monitoring System) * EBS braking system * Drum brake * BPW axle * Parabolic springs * Front support winch * Rear spring-assisted square tube supports with base plate, safety locking pins for variable support heights * Drawbar with 40 mm bolt coupling (height-adjustable in mm) * 15-pin electrical connector * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and cross members * Closed steel mudguards with splash protection Bodpfx Adeu I Iq Eensww * Closed lateral underrun protection, suitable for use as advertising space * Plastic toolbox with base insert (horizontal installation) approx. 500 x 350 x 400 mm * Swiveling cable drum mount, light width between drum arms 1,700 mm - with tension lock for drum securing at the ends of the support arms and a center-mounted claw lock for securing the cable drum mount to the chassis * Motor-hydraulic drum drive with oil motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft with 76 mm diameter, including centering and rotatable ends * 1 pair of stepped polyamide centering cones * Hydraulic power unit with diesel engine * Fuel tank and manual starter * 6.5 HP with gear pump (150 bar) * Surface hot-dip galvanized * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2025, * T3 Profile 30.0: * EBS brake system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic suspension Bwsdpfx Adel Th Adonow * Mechanical rear axle equalizer * Side underrun protection * Rear swing-down supports on the chassis frame * Mechanically adjustable warning sign panels front and rear * Front axle with closed plastic mudguards, rear axle with straight galvanized steel skirts, each with spray protection * Side and rear contour marking tape (reflective) * Flip-top lid (hot-dip galvanized) for the toolbox on the turntable platform * Multi-voltage electrical system * LED tail lights * Removable rotating beacon at the rear * Drawbar with 40 mm towing eye and height adjustment via tension spring and turnbuckle * 15-pin electrical connector * 4 stake pockets per side (stakes not included), can also be used for lashing * Load securing package consisting of: 2 lashing eyes (6.4 t) front left & right on the main frame of the turntable platform, 5 pairs of UVV folding and lowering lashing rings, loadable in all directions and recessed in the outer frame – corners rated at 13.4 t, otherwise 10 t * 6 pairs mechanical folding outriggers for 3 m overall width (not included on the rear slope) * Widening boards stored in the center of the load area * Excavator arm rest over the rear axle up to the end crossmember, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings at the sides of the excavator arm rest) * Hydraulically operated single-piece ramps (approx. 3,000 x 720 mm), laterally adjustable * Load area above the turntable: approx. 1,960 x 2,520 mm * Unladen loading height: approx. 1,070 mm * Rear load area: approx. 6,500 x 2,520 mm * Unladen loading height: approx. 910 mm (incl. 860 mm approach ramp) * Chassis, turntable, drawbar and ramps hot-dip galvanized * Axles, springs, air tanks, etc. painted in black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * -- Technically possible gross vehicle weight: 30,000 kg -- * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Available from CW 38/2025