Müller-Mitteltal Kwh Prikolice nakup rabljenega (240)

Stanje: novo, skupna masa: 21.000 kg, največja dovoljena obremenitev: 16.600 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2025, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal ETÜ-TAR 21 Tandem - Low-bed / Platform Trailer, drive-over Ref. No. for enquiries: 11520 NEW VEHICLE incl. COC * GVW: 21t, Payload: 16.60t, galvanised chassis * Immediately available * Platform variant with 400mm high front wall, ramp safety system with ramp holding rods and angled support * Version GVW 21t: reinforced frame and axle, axle spacing 1,810 mm * Deck height approx. 910 mm loaded / approx. 940 mm unloaded * 7,000mm loading platform with 400mm high front wall * Extended ramps: 3,000 mm, single-piece, hot-dip galvanised ramp with hot-dip galvanised grating * Ramp assist system with vertically mounted, adjustable springs for easy single-person operation * La-Si package: 4 UVV certified lashing brackets (LC 8,000 daN) installed in the existing hole pattern in the 45° outer frame (approx. 5mm offset), positioned approx. 1,000 mm from the front and rear crossmember respectively Crodpfx Adswllrij Ueh * 10 UVV certified lashing brackets LC 3,000 daN retractable in the existing outer frame hole pattern * Softwood floor, 50mm thick. 2 UVV certified lashing rings recessed at the front and rear crossmember with LC 10,000 daN * Additional lashing options via holes (Ø 50 mm, LC 1,200 daN) in the front and rear crossmembers * Preparation for retrofitting container locks * Gigant axles with air suspension incl. EBS 2S/2M * Raise and lower function * 235/75R 17.5 (8-fold) twin tyres with tyre pressure monitoring sensors * 1 plastic toolbox mounted in front of the front wall, right-hand side in driving direction * LED lighting system * 7-pin socket at rear, wired for overlength lighting with taillight (58 R) and ground * 2 LED reversing lights at rear * Flashing side marker lights * Oversize warning board * 1 detachable all-round LED beacon incl. holder and installation * Foldable supports at rear, support leg at front with geared winch ---- Leasing example from our partner MMV Leasing: €639 net/month for 60 months with no down payment and “0” euro residual value Other terms available with/without down payment/residual value! We are MüllerMitteltal authorized dealers ---- * Our opening hours * Monday - Thursday: 08:00 - 17:00 * Friday: 08:00 - 15:00 * Outside office hours by appointment * We speak German, English, Russian, Polish, and French * Leasing, financing, and trade-in available

Stanje: rabljeno, konfiguracija osi: 3 osi, skupna masa: 24.000 kg, lastna masa: 6.350 kg, največja dovoljena obremenitev: 17.650 kg, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.500 mm, prva registracija: 08/2008, vzmetenje: zrak, številka stroja/vozila: GE11/142/2022, Very well-maintained vehicle from first ownership Cjdpjn Aw Hkefx Ad Uerh Three-axle low-loader trailer with drive-over ramps Low-loader with loading ramp Heavy-duty transport Type T3 Komakt 30.0 Length: 8,500 mm Width: 2,500 mm Air suspension Commercial/Export net price – €19,990 Subject to changes, prior sale, and errors. ===== Telephone 2 Mobile =====

Stanje: novo, skupna masa: 14.400 kg, največja dovoljena obremenitev: 10.950 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2024, * ETÜ-TA-ER 14.4 Flatbed: * TPMS (Tire Pressure Monitoring System) * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 ton BPW axles * Air suspension with lifting and lowering function * Mechanically adjustable 3 m warning sign boards at front and rear * Drawbar height-adjustable by 300 mm with 40 mm flange towing eye * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (resulting in B-dimension approx. 8,080 mm) * Landing gear crank at front * External folding support legs at rear * Plastic toolboxes approx. 750 x 350 x 300 mm each, mounted left and right side * Side underrun protection * Rear underrun protection Crsdpfsm Tgxwex Ad Ujh * Plastic quarter mudguards * 15-pin electrical connector * LED lighting system 12 / 24 V * 2 additional LED reversing lights at rear (activated via reverse gear) * 1 removable LED beacon (including bracket) at rear * 50 mm softwood floor * 2 pairs of container locks (extendable to 3 m container external width) and lockable * Locking dimension retracted according to ISO - DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not DIN conform) with an absolute external width of 3,000 mm * Perforated outer frame approx. 45° angled with 2 t lashing capacity every 480 mm, installation of 3 t drop lashing rings every 600 mm possible – each side equipped with 5 x 3 t UVV lashing rings, in the front and rear corners each 1 x 6.3 t lashing ring (front directly behind container locks in timber floor, rear in end crossmember), various 1.2 t lashing point options in front wall and end crossmember * 1 pair of aluminum slide-in ramps approx. 3,570 x 410 mm (load capacity 10 t / pair) suitable for rubber-tired and tracked vehicles * Rear storage compartment recessed below loading bed in chassis * ---Chassis, drawbar, front wall, underrun protection and rear supports hot-dip galvanized--- * Axles, air reservoirs, landing crank at front and flange towing eye painted black * New vehicle with manufacturer warranty * Errors and prior sale excepted * Immediately available ex works Egestorf at the A7

Stanje: novo, skupna masa: 40.000 kg, največja dovoljena obremenitev: 31.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.290 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 950 mm, * PT 40.0 Profile: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with raising/lowering system and RtR valve * Manometer pressure display for load weight determination (axles separated into 2 air suspension circuits) * Side underrun protection * Swing-down supports at the rear of the chassis frame * Mechanically adjustable warning panel sets front and rear * Front axle: plastic quarter mudguards with spray protection * Rear axle: straight galvanized steel skirts with spray protection * Reflective contour markings on sides and rear * EBS multi-voltage system with 12 & 24 V electrics Csdpfjl Tlhrjx Ad Uorh * 15-pin power connector * LED lighting system 12 / 24 V * Removable LED beacon at rear * 2 LED reversing lights (activated via reverse gear) * Tow bar with 50 mm towing eye and height adjustment * Tool box made of galvanized steel, black powder coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high * Extension in front of turntable platform approx. 490 mm long with 45° corners * ROBOTER-welded anti-slip coating on the turntable platform steel plate * Load securing package consisting of: 1 x 13.4 t UVV lashing ring front left & right in front of bulkhead support, 4 mounting holes per side in the turntable platform each with 2 t lashing capacity, 1 pair of 13.4 t lashing rings suspended at rear left & right before the rear cross member, 4 pairs of 10 t UVV lashing rings per side, swiveling and lowerable, loadable in all directions and recessed into side frame, 3 stake pockets per side with 2 t lashing option each * Hot-dip galvanized mechanical folding outriggers for 3 m overall width (not on the rear slope) * Timber plank holder for width extensions under the chassis, longitudinal left * Excavator arm rest above rear axle up to end plate, approx. 2,100 mm long and 190 mm deep, 2 pairs of 6.4 t lashing rings per side in the excavator arm rest * Hardwood flooring on the running surfaces of the low-loader platform * Hydraulically operated single-piece ramps (approx. 3,000 x 720 mm), mechanically adjustable width * Ramp outer planks made of hardwood * Steel construction prepped for 6-way control sliders * Unladen loading height approx. 950 mm +/- 20 mm (chassis) * Turntable, folding outriggers, mechanical support legs, ramps are hot-dip galvanized * -- Axles, air tanks, tow bar painted black -- * Tyres 235/75 R 17.5 * Vehicle registered for one day in 07/2024, due to missing tire pressure monitoring system and was not loaded/used * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, skupna masa: 30.000 kg, največja dovoljena obremenitev: 23.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.380 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2024, * PT 30 Profile: Crodjtplwijpfx Ad Ush * EBS (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes * 3 x 11 t Gigant axles * Air suspension with lift and lowering function as well as RtR valve * Smart-Board mounted on trailer as information tool (separate axle load indication front and rear) * Tyre pressure monitoring with display option in the truck via EBS signal, no installation required on the truck side * Side underrun protection * Swing-out supports at the rear of the chassis frame * Mechanically adjustable warning board packages front and rear * Front axle: plastic quarter mudguards with spray protection * Rear axle: straight, galvanised steel sheet skirts with spray protection * Contour marking tape, reflective on sides and rear * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear * Drawbar 1,200 mm long with 40 mm towing eye and height adjustment by means of draw spring & turnbuckle * Tool box, galvanised steel, approx. 650 x 300 x 600 mm, black powder-coated, mounted on right side * Accessory box in turntable with folding lid, 2 built-in container locks (immediately behind turntable platform) * ROBOT-welded anti-slip coating on turntable platform steel plate (protruding weld seams) * Load securing package consisting of: 2 lashing rings (13.4 t) front left & right on front wall support, front & rear 1 pair UVV lashing rings (13.4 t) as well as 3 pairs each side UVV lashing rings (10 t), swivelling and lowerable, loadable in all directions and recessed in outer frame, each side 3 stanchion pockets with simultaneous 2 t lashing capacity * 6 pairs mechanical folding outriggers for 3 m overall width (not on rear bevel) * Widening boards stored in the centre of the load area * Hydraulic one-piece ramps approx. 3,000 x 720 mm * Mechanically adjustable sideways * 4-way control block for later retrofitting of hydraulic ramp shifting * Chassis, turntable, folding outriggers, drop supports and approach ramps hot-dip galvanised * Axles, slewing ring, air tanks, drawbar painted in a shade of black * Loading edge height (laden): approx. 910 mm +/- 20 mm air suspension * New vehicle with manufacturer’s warranty * Subject to prior sale and errors * Immediately available ex Egestorf

Stanje: novo, skupna masa: 27.000 kg, največja dovoljena obremenitev: 20.200 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2024, * ETÜ-TR 27.0 flatbed: * EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lifting and lowering function with RTR feature * 1st axle liftable * Last axle as trailing steering axle with electro-pneumatic steering lock via reverse gear PIN (lock of the trailing axle from the towing vehicle for maneuvering purposes – no truck-side installation required – assigned to PIN 10 in the 15-pin connector, for maneuvering only, not in public road traffic) * SmartBoard control box as infotool with pressure sensors for total axle load display * Tire pressure monitoring with display capability in the truck via EBS signal, no truck-side installation required * Fixed center drawbar with 50 mm flange towing eye (loaded: 900 mm, adjustable in height at the head plate) * Mechanical landing gear at the front, mechanical swiveling supports at the chassis rear * Mechanically adjustable warning sign package front and rear * Toolboxes made of galvanized steel sheet – black powder-coated – approx. 650 x 300 x 600 mm, right side * 15-pin power connector * LED rear lights * Removable LED beacon incl. holder and installation * 2 x LED reverse lights at the rear (controlled via reverse gear) * Flashing LED side marker lights * 60 mm larch/Douglas fir wooden floor * 400 mm steel front wall, insertable * Perforated outer frame approx. 45° angled with fixture for 3 t folding lashing shackles * In each corner 1 x 10 t lashing ring, plus each side 2 x 10 t and 3 x 6.3 t lashing rings * Multiple holes in front and rear cross members for securing up to 1.2 t * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm, mechanically adjustable sideways * Four-way hydraulic valve block for potential retrofitting of hydraulic ramp shifter Csdpfx Adjr Dpzxo Uerh * Chassis, drawbar, front wall, mechanical rear supports, and ramps hot-dip galvanized * Axles, air tanks, flange towing eye, and front landing gear painted black * --Preparation for possible retrofitting of side boards-- * New vehicle with manufacturer’s warranty * Errors and prior sale reserved * Immediately available ex Egestorf

Stanje: novo, skupna masa: 30.000 kg, največja dovoljena obremenitev: 16.400 kg, konfiguracija osi: 3 osi, Leto izdelave: 2024, * T3 Profile 30.0: * EBS-E (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Air suspension with lifting and lowering function * SmartBoard as an information tool on the trailer with pressure sensors for display of total axle load per axle group * Side underrun protection * Mechanically adjustable warning sign panels front and rear * Front axle with closed plastic mudguards and rear axle with straight, galvanized steel panels, each with spray protection * Hinged lid (hot-dip galvanized) for toolbox on turntable platform * Toolbox made of galvanized steel sheet approx. 650 x 300 x 600 mm (black powder-coated) mounted on right side * 15-pin power connector * LED lighting 12/24 V * LED revolving beacon (removable), rear * Side marker lights with indicator activation * Drawbar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * Tire pressure monitoring system with display capability in the truck via EBS signal (no installation required on the truck) * Rubber covering on the folding ramps as well as on the inclined ramp surface, left and right (approx. 860 mm long) * Rubber covering on the longitudinal beams from front to rear cross beam * Hardwood flooring on the walking surfaces of the low bed platform Crodpfx Adjq Dyvco Ush * Four stake pockets per side, each with simultaneous 2 t lashing capability * Load securing package comprising 5 pairs of UVV lashing rings, swiveling and lowerable, loadable in all directions, recessed into the outer frame – in corners 13.4 t, otherwise 10 t * Six pairs of mechanical folding outriggers for 3 m total width (not in rear incline) * Plank holder under the cargo area, lengthwise * Roller stop in front of the front cross member, raised, with one 6.4 t lashing ring per side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically deployable tip section and load-holding valves * Hydraulic side ramp displacement * Rear hydraulic support (single-stage cylinder) * Hydraulic flow divider in the trailer (for hydraulic pump capacity in truck over 40 up to max. 140 l/min) * Hydraulic control block, splash-proof * Dual-line hydraulics * Loading area above turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (including 860 mm ramped section) * Loaded platform height: approx. 890 mm +/- 20 mm with air suspension * Chassis, turntable, roller stop, folding extensions & ramps hot-dip galvanized * Axles, turntable, drawbar, air tanks, etc. painted in black * Loaded platform height: approx. 890 mm +/- 20 mm * New vehicle with manufacturer warranty * Subject to prior sale and errors * Immediately available ex Egestorf

Stanje: novo, skupna masa: 14.400 kg, največja dovoljena obremenitev: 10.800 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2025, * ETÜ-TA-R 14.4: * EBS braking system * Emergency release device for spring-actuated cylinders * Drum brakes * 2 x 7-ton Gigant axles * Parabolic springs with equalization unit * Height-adjustable drawbar, adjustable by approx. 300 mm * Drawbar extension by 250 mm to 2,250 mm * Tire pressure monitoring with in-cab display via EBS signal – no installation required on the truck side * Landing gear at the front * Rear external folding supports * 15-pin electrical connector * LED lighting system 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics Crsdpfx Adorwc R Rj Ujh * Plastic toolbox approx. 858 x 500 x 500 mm mounted front right on the bulkhead * Side underrun protection * Plastic quarter mudguards * 50 mm softwood flooring * Pre-installed equipment before the bulkhead for subsequent installation of container locks * Bolted 400 mm smooth metal bulkhead * Bolted rear stanchions * Drop sides with spring assist * Perforated outer frame, approx. 45° bent, with 2 t lashing capacity every 480 mm; installation of 3 t folding lashing rings every 600 mm possible; 1 x 6.3 t lashing point each in the front and rear corners; various 1.2 t lashing options in the front and rear cross members * One-piece hydraulic mesh ramps approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Hydraulic flow divider in the trailer (for hydraulic pump output on truck exceeding 40 ltr./min. up to max. 140 ltr./min.) * Chassis, drawbar, bulkhead, mechanical folding supports, and ramps hot-dip galvanized * Axles, springs, air tanks, landing gear, and flange towing eye painted in black * Side walls painted in RAL 9010 pure white * Side wall painting in any RAL color available at extra cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from CW 15/2025 * Sample images

Stanje: novo, skupna masa: 50.000 kg, največja dovoljena obremenitev: 38.900 kg, konfiguracija osi: 3 osi, Leto izdelave: 2025, * T5 section 50.0: * Wabco EBS (electronic braking system) * TPMS (tyre pressure monitoring system) * Emergency release for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Last axle with steering function (locking of the steered trailing axle from the driver’s cab for manoeuvring purposes possible without truck-side installation, as well as additional switch on the trailer); locking must be deactivated before entering public roads * Air suspension, lifting/lowering system with RtR valve * 3rd axle liftable (ride height +30 mm with lifted axle) * Forced unloading and lowering of the lift axle for manoeuvring (requires truck-side installation) with speed-dependent activation via EBS electronics * Smartboard as information tool with pressure sensors for displaying total axle load per axle group * Tyre pressure monitoring with display option in the truck via EBS signal (without truck-side installation) * Mechanical warning sign kit for 3 m total width * Drawbar 1,500 mm long with 50 mm eye and manual height adjustment * LED lighting system 12 / 24 V * LED beacon (removable) at the rear * Tool box made of galvanised steel sheet approx. 650 x 300 x 600 mm, left side * Plastic mudguards front axle and galvanised steel mudguards at the rear * Platform lead frame with 45° corners and 3 storage compartments with lockable folding lids (lids open to the rear) * Shortening of the low-loader platform by 500 mm to 6,280 mm incl. extended front offset by 500 mm * Load securing package: 2 x 6.4 t lashing eyes at the front corners, 2 x 13.4 t UVV lashing rings on each side at the front and rear corners, 5 x 10 t UVV lashing rings on each side (pivotable, lowerable, loadable in all directions), 4 stake pockets per side each with 2 t lashing option, 1 x 16 t UVV lashing ring on rear cross member * Rubber covering on the folding ramp, approach angle and on the running surface of the low-loader platform * Bamboo wood in between the longitudinal beams in front of excavator arm support * Telescopic and folding extension beams for 3 m total width (beam holders underneath the chassis, right-hand side) * Continuous excavator arm support with reinforcement profile from last axle to rear cross member, approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on the side in the excavator arm support * Hydraulic folding ramp with dual-circuit hydraulics and adjustable tip section approx. 4,650 x 720 mm, incl. load-holding valves and hydraulic side shift Crodpfx Adol Tlh Dj Ujh * Hydraulic rear support * Hydraulic flow divider (with truck hydraulic pump capacity over 40 l/min up to max. 140 l/min) * Loaded deck height 890 mm +/- 20 mm due to air suspension * Deck area above turntable: 2,600 + 390 x 2,520 mm * Low-bed loading area: 6,280 + 500 x 2,520 mm, incl. 860 mm approach angle * Chassis, bogie, drawbar, extension consoles, loading ramps hot-dip galvanised * Drawbar, axles, hydraulic axle supports and air tanks painted in black tone * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, skupna masa: 14.400 kg, največja dovoljena obremenitev: 10.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, * ETK-TA-R 14.4: Codpfstr St Hsx Ad Ujrh * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem equalizer unit * Tire pressure monitoring with indication in the truck via EBS signal; no truck-side installation required * 300 mm height-adjustable drawbar with 40 mm flange towing eye * Mechanical landing leg at the front * Rear: 2 mechanical folding support legs * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right-hand side * 15-pin electrical connector * Multi-chamber tail lights * Bolted underrun protection * Plastic quarter mudguards * Net hooks on the sides and rear in the mounts for central locking, as well as 2 pcs. on the front wall * Main frame made of fine-grain steel * Steel pallet two-way tipper body: Fixed front wall made of plain sheet, continuous side walls – folding without center stakes with drop-side assist and pendulum function via manual central locking * Rear stakes are bolted * Steel rear wall inserted in front of the ramps * Lashing points: 1 x 5 t in each corner; 4 x 3 t recessed lashing rings per side in the outer frame * 4 mm floor plate made of fine-grain steel * Two-part mechanical grating ramps with aluminum tip: 2,150 + 1,300 mm x 600 mm (can be manually telescoped up to 80 mm overlap) * Chassis, drawbar, rear stakes, underrun protection, mechanical support legs, and loading ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and landing leg painted in black * Side walls and platform in RAL 9010 pure white * Painting of the side walls and tipping platform in a different RAL color available at extra cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available from Egestorf on the A7

Stanje: novo, skupna masa: 14.400 kg, največja dovoljena obremenitev: 12.080 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 3.900 mm, širina tovornega prostora: 1.920 mm, višina nakladalnega prostora: 415 mm, Leto izdelave: 2022, Oprema: ABS, dvižna zadnja plošča, * ETM-TA 14.4: * Wabco ABS braking system * Emergency release device for spring-loaded cylinders * Drum brakes, 2 x 7 t Gigant axles * Parabolic springs with tandem compensating aggregate * Height-adjustable drawbar (+/- 150 mm) with 40 mm screw coupling eye * Jost landing gear at the front, side underrun protection * Foldable A-panel at the rear * 15-pin electrical connector, multi-chamber tail lights Codpfx Adoq Euars Uerh * Fixed steel front and side panels * Removable steel rear panel * Floor made of 50 mm softwood * 1 sliding sheet wear plate 750 x 1,000 mm at the front area including 2 removable trough stops at the front, mountable in 2 positions each * 4 removable trough stops, mountable in 2 positions to laterally center the troughs * On each side, 1 x (13.5 t) UVV lashing point for securing tensioning elements * 2 ratchet tensioners (spindle adjustment) with compensating chain and quick shortening device (tensioning force 6,300 kg) * Rear cross member for attaching aluminum loading ramps including 2 additional support legs at the rear * Loading edge unloaded approx. 710 mm * Chassis, front wall, side walls, mudguards, drawbar, and rear support legs hot-dip galvanized * Axles, springs, landing gear, and air tank painted black * Tyres: 285/70R19.5, wheelbase: 1,140 mm * Loading edge unloaded: approx. 710 mm, sold without container * Color: hot-dip galvanized * Vehicle has a one-day registration in 06/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale reserved * Immediately available ex Egestorf on the A7

Stanje: novo, skupna masa: 24.000 kg, največja dovoljena obremenitev: 18.900 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, * TRA-Kombi 24.0: Codpfx Aspk D Awsd Uorh * Wabco EBS-E (electronic brake system) * Emergency release device for spring-loaded cylinders * TPMS (tire pressure monitoring system) * Drum brakes * 3 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Liftable central axle * Pneumatically lowerable drawbar, 2,100 mm long, with 50 mm towing eye and height adjustment * Tool box made of powder-coated sheet steel and spare wheel carrier in basket design, right-hand side * Reflective contour tape on sides and rear * Side underrun protection * Plastic quarter mudguards with splash protection * Plastic rear impact protection buffers * LED tail lights * 15-pin power connector * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) for container guiding rails * Steel floor with roller recesses in the bogie area * For roll-off container transport, container lengths of 5,500 - 7,000 mm possible * Pneumatic 4-point clamp locking as well as mechanical plug-in stop angles at the front tracks * Load securing certificate according to DIN 30722-1 * Transport of up to 2 skip containers with a maximum of 10 m³ volume possible * Including 8 repositionable container supports for lateral centering of skips, front 4 with tilting stops * 3 pairs of 10 t UVV lashing rings on the side for attachment of tensioning elements for positive and non-positive load securing * 4 shamrock-shaped lashing rails on each side and 1 pair of 13.4 t UVV lashing rings at the front * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * Weld bead as anti-slip coating in the running rail area of the approach slope * Mechanical drop-down supports at the rear * 1 pair of aluminum loading ramps (16 t/pair), 2,800 x 400 mm, suitable for rubber-tired and tracked vehicles (lockable rear storage compartment) * Tires: 235/75 R17.5 * Loaded ride height approx. 1003 mm * Payload 18,900 kg * Technically permissible gross weight 27,000 kg * Axles, slewing ring, drawbar and air tanks painted black * New vehicle, unregistered, with manufacturer warranty * Errors and prior sale excepted * Available from calendar week 23/2025

Stanje: novo, skupna masa: 19.000 kg, največja dovoljena obremenitev: 14.550 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2024, * ETÜ-TA-R 19.0: * Wabco EBS-E (electronic braking system) * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 11 t Gigant axles * Air suspension, drawbar with 50 mm flange eye and height-adjustable drawbar * Jost landing gear at the front * External folding supports at the rear * Toolbox made of galvanized sheet steel approx. 650 x 350 x 320 mm mounted laterally right (black powder-coated) * Side underrun protection * Plastic quarter-mudguards * 15-pin electrical connector * LED tail lights * Reinforcement package for drill rig transport on chassis – load height +20 mm * 50 mm softwood floor, clamped design * Preparation for subsequent fitting of container locks in front of the bulkhead * Bolt-on front wall made of smooth steel sheet * Trapezoidal-profiled side walls made of steel sheet, foldable with drop-side spring assists * Steel rear wall, retractable between the ramps – storage bracket inside front wall when not in use * Bolted rear stanchions Crjdpfx Adspk D D Ho Ujh * Perforated outer frame, approx. 45° bent, with 2 t lashing force every 480 mm * Option to install 3 t folding lashing rings every 600 mm * In each front and rear corner, 1 x 10 t lashing ring, front and end beams with multiple holes for 1.2 t lashing points * One-piece mechanical grated ramps with spring system for single-person operation, approx. 2,750 x 620 mm (collapsible to 20 mm) * Rear approach angle approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, rear folding supports, and ramps hot-dip galvanized * Axles, springs, air reservoirs, and landing gear painted black * Wheelbase: 1,310 mm * Tires: 235/75R17.5 * Drop-side panels painted RAL 9010 pure white * Side panels can be painted in any RAL color at extra cost * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available immediately from Egestorf

Stanje: novo, skupna masa: 14.400 kg, največja dovoljena obremenitev: 10.950 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2024, * ETÜ-TA-ER 14.4 flatbed: * TPMS (Tire Pressure Monitoring System) * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 t BPW axles * Air suspension with lift and lowering system * Mechanically adjustable 3 m warning panel sets front and rear * Drawbar height-adjustable by 300 mm with 40 mm flange draw-eye * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (resulting in a B-dimension of approx. 8,080 mm) * Support winch at the front * External folding supports at the rear * Plastic tool boxes approx. 750 x 350 x 300 mm on each side left & right * Side underrun protection * Rear underrun guard * Plastic quarter mudguards * 15-pin power connector * LED lighting system 12 / 24 V * 2 additional LED reversing lights at the rear (controlled via reverse gear) * 1 removable LED beacon, incl. holder, at the rear * 400 mm high bolted front wall * 50 mm softwood floor Codpfxev D Tbke Ad Uerh * 2 pairs of container locks (extendable to 3 m outer container width) and lockable, locking dimension retracted according to ISO - DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not DIN-compliant) with an absolute external width of 3,000 mm * Perforated outer frame approx. 45 degrees angled with 2 t lashing capacity every 480 mm; installation of 3 t recessed lashing rings possible every 600 mm; fitted with 5 x 3 t UVV-compliant lashing rings per side; at each of the four corners, 1 x 6.3 t lashing point (front directly behind the container locks in the wood floor, rear in the end crossmember); various 1.2 t lashing options via bores in the front and rear crossmembers * 1 pair of approx. 3,570 x 410 mm aluminum slide-in ramps (load capacity 10 t / pair), suitable for rubber-tired and tracked vehicles * Rear storage compartment recessed below the loading platform in the chassis * ---Chassis, drawbar, front wall, underrun guard, and rear supports hot-dip galvanized--- * Axles, air tanks, front support winch and flange draw-eye painted in black * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available ex works Egestorf on the A7

Stanje: novo, skupna masa: 14.400 kg, največja dovoljena obremenitev: 10.750 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-R 14.4: * RDÜ tire pressure monitoring system * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with compensator unit * Drawbar height adjustable by approx. 300 mm – drawbar extension by 250 mm to 2,250 mm * 15-pin power connector Crodpfjv Eq Evex Ad Ush * LED lighting * Front landing gear (support winch) * External foldable rear support legs * Plastic toolbox approx. 858 x 500 x 500 mm, mounted at the front right on the front wall * Side underrun protection * Plastic quarter mudguards * 50 mm softwood flooring * In front of the front wall and rear slope, preparation for retrofitting container locks for transporting 20" containers * Bolted smooth sheet metal front wall * Drop-down steel side walls – trapezoidal profile – split once in the middle * Insertable steel rear wall; can be stored inside in the ramp holder at the front wall when not in use * Bolted rear corner posts * Perforated outer frame, kinked at approx. 45 degrees, 2 t lashing capacity every 480 mm; possible installation of 3 t folding lashing rings every 600 mm; each front and rear corner with 1 x 6.3 t lashing point; various boreholes in the front and end crossmembers for 1.2 t lashing options * One-piece mechanical grating loading ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be slid together to 20 mm) * Rear entry slope approx. 860 mm chassis * Drawbar, front wall, tailgate, foldable supports and loading ramps hot-dip galvanized * --- Axles, springs, air tanks, flange drawbar eye as well as landing gear painted in a black tone --- * Reinforced and certified body according to EN 12642 XL incl. load securing certificate -- * Wheelbase 1,140 mm * Side wall painting in RAL 9010 pure white * Painting of side walls in a different RAL color available at extra cost * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Immediately available from Egestorf

Stanje: novo, skupna masa: 11.900 kg, največja dovoljena obremenitev: 8.870 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-R 11.9: * Loading area: 6.27 m Codpfx Adeq Ra D Ej Uerh * Suitable for container transport * TPMS (Tire Pressure Monitoring System) * EBS braking system * Emergency release device for spring-actuated cylinders * Drum brakes, 2 x 5.5 t BPW axles * Parabolic springs with compensating unit * Drawbar height-adjustable by 300 mm * Jost landing gear at the front * Externally mounted hot-dip galvanized folding support legs at the rear * Plastic quarter mudguards * LED lighting * Hot-dip galvanized chassis, drawbar, front wall, rear wall, rear stanchions, and loading ramps * 50mm softwood floor * Bracket in front of the front wall for retrofitting container locks * Bolted smooth sheet front wall * Trapezoidal-profile drop-side steel side panels with sideboard spring assister * Steel rear wall can be slotted between the ramp holders when not in use and stored in front of the front wall internally * Bolted rear stanchions * Perforated external frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Option to install 3 t recessed lashing rings every 600 mm * 1 x 6.3 t lashing point in each front and rear corner * Various holes in the front and end crossmembers for 1.2 t lashing options * One-piece mechanical loading ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be collapsed to 20 mm spacing) * Rear drive-up slope approx. 860 mm * Wheelbase: 990 mm * Tires: 235/75R17.5 * Side walls painted RAL 9010 pure white * Side panels can be painted in any RAL color for an extra charge * Plastic toolbox * Errors and prior sale reserved * Immediately available from Egestorf

Stanje: novo, skupna masa: 30.000 kg, največja dovoljena obremenitev: 23.700 kg, konfiguracija osi: 3 osi, * T3 Profi 30.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Air suspension with manual lowering at the rear * Pressure gauge for determining load weight (axles separated into 2 air suspension circuits) * Side underrun protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages front and rear * Front closed plastic mudguards and rear straight galvanized steel skirts, both with splash protection * Reflective contour marking tape on the sides and rear * Foldable toolbox lid (hot-dip galvanized) on the turntable platform * LED tail lights * Removable rotating beacon at the rear * Drawbar with 40 mm towing eye and height adjustment via draw spring & turnbuckle * 2 x 7-pin electrical connectors * 4 stake pockets per side, each offering 2 t lashing capacity * Load securing package including: 2 lashing eyelets (6.4 t) at the front left & right on the main frame of the turntable platform, 5 pairs of UVV-compliant adjustable and folding lashing rings, loadable in all directions and recessed into the outer frame – corner capacity 13.4 t, otherwise 10 t * 6 pairs of mechanical folding outriggers for 3 m overall width (except rear angle) * Broadening planks stored in the middle of the loading platform * Hydraulic one-piece loading ramps (approx. 3,000 x 720 mm), laterally adjustable * Loading area above turntable: approx. 1,960 x 2,520 mm * Unladen loading height: approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height: approx. 910 mm (including 860 mm approach slope) * Chassis, turntable, drawbar, folding widenings & ramps hot-dip galvanized * Axles, turntable, air tanks, etc. painted in black * Tires: 235/75 R 17.5 * Payload approx. 24,000 kg at 30,000 kg gross weight * New vehicle with manufacturer’s warranty * Subject to errors and prior sale Cedpfx Ajl Tpwyed Ujrh * Immediately available ex Egestorf

Stanje: novo, skupna masa: 18.000 kg, največja dovoljena obremenitev: 14.660 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-R 19.0: * Wabco EBS brake system * RDÜ tire pressure monitoring system * Emergency release mechanism for spring brake cylinders * Drum brakes * 2 x 10 t BPW Eco axles * Parabolic springs - 110 mm wide - with tandem equalization unit * Drawbar with 50 mm flange drawbar eye and height-adjustable drawbar * Jost landing gear at front * External folding supports at rear * Side underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED tail lights * 50 mm softwood flooring * Pre-fitted for retrofitting container locks in front of the headboard * Bolted headboard made of smooth sheet metal * Trapezoidal profile steel side panels, foldable with sideboard spring lifter * Steel rear wall, insertable between the ramps; storage bracket inside the headboard when not in use * Bolted rear stanchions Crjdpfsl Th Hwex Ad Ush * Perforated outer frame, angled at approx. 45°, with 2 t lashing capacity every 480 mm * Option to install 3 t retractable lashing rings every 600 mm * In each front and rear corner, 1 x 10 t lashing ring; multiple holes in the headboard and rear cross-member for 1.2 t lashing options * One-piece mechanical grating entry ramps with spring mechanism for single-person operation, approx. 2,750 x 620 mm (can be collapsed to 20 mm) * Rear entry slope approx. 860 mm * Chassis, drawbar, headboard, rear wall, entry ramps and folding supports hot-dip galvanized * Sideboard painted in RAL 9010 pure white * Side panels can be painted in any RAL color at extra cost * Axles, springs, air tanks, drawbar eye, and landing gear painted black * New vehicle with full manufacturer's warranty * Errors and prior sale excepted * Immediately available ex works Egestorf

Stanje: novo, skupna masa: 11.900 kg, največja dovoljena obremenitev: 8.800 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.370 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-R 11.9: * Load area 5.37 m * TPMS (Tire Pressure Monitoring System) * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes, 2 x 5.5 t Gigant axles * Parabolic springs with compensating unit * Drawbar adjustable in height by approx. 300 mm * Jost landing gear at the front * Rear folding external supports * Plastic toolbox front right, mounted externally on the front wall * Side underrun protection * LED lighting * Plastic quarter-mudguards * 50 mm softwood floor * Bolted front wall made of smooth sheet metal * Trapezoidal steel side walls, foldable, with tailboard spring assist * Sliding steel rear wall, stowable in front of the front wall between the ramp mounts when not in use * Rear stanchions bolted on * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * In each front and rear corner, 1 x 6.3 t lashing ring * Various holes in the front and rear crossmembers for 1.2 t lashing options * One-piece mechanical grating loading ramps with spring mechanism for one-man operation, approx. 2,750 x 600 mm (can be collapsed to 20 mm) * Tapered rear frame, approx. 860 mm chassis * Drawbar, front wall, tailgate, folding supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, and 40 mm flange towing eye painted in black * Wheelbase: 990 mm * Tires: 235/75R17.5 * Side walls painted in RAL2011 deep orange * Side wall painting in other RAL colors available for an extra charge * New vehicle with manufacturer warranty * Errors and prior sale excepted * Immediately available ex Egestorf Cedpfx Aol Th Nred Ujrh

Stanje: novo, skupna masa: 14.400 kg, največja dovoljena obremenitev: 10.360 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-ER 14.4: * RDÜ (Tyre pressure monitoring system with display capability in the truck via EBS signal, no installation required on the truck side) * Electronic braking system (EBS) * Emergency release device for spring brake cylinders Crodjpk D Dqspfx Ad Ush * Drum brakes * 2 x 5.5 t Gigant axles * Air suspension with lifting and lowering function * Drawbar height-adjustable by approx. 300 mm * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding support legs at the rear * Plastic toolbox, front right, mounted on the front wall * Side underrun protection * Plastic quarter mudguards * LED lighting system * 15-pin power plug * Hot-dip galvanized chassis, drawbar, front and rear wall * 50 mm softwood floor * Prepared for retrofitting 20" container locks at the front and rear * Bolted front wall made of flat sheet steel * Drop-down steel sheet side walls – trapezoidal profile – with drop-side spring assist * Hot-dip galvanized, bolted rear stanchions * Perforated outer frame, approx. 45-degree angled, with 2 t lashing capacity every 480 mm; installation of 3 t drop lashing rings every 600 mm possible; one 6.3 t lashing ring in each corner, front and rear; various anchoring holes (1.2 t) in the front and end crossmembers * 1 pair of aluminum loading ramps, approx. 3,310 x 400 mm (carrying capacity 8 t/pair), suitable for rubber-tyred and tracked vehicles, stored at the rear in a compartment recessed in the chassis under the loading area * Vehicle fully hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Available immediately ex Egestorf

Stanje: novo, skupna masa: 18.000 kg, največja dovoljena obremenitev: 14.650 kg, konfiguracija osi: 2 osi, Leto izdelave: 2024, * RS-T 18.0 / 018: * Wabco EBS-E (electronic braking system) Crsdpfxsl Tqkwe Ad Ush * TPMS (Tire Pressure Monitoring System) * Emergency release mechanism for spring-loaded cylinders * Disc brakes * Duomatic brake coupling * 2 x 10-ton SAF axles * Air suspension with automatic lowering when uncoupling the brakes * Drawbar 2,300 mm long with 40 mm towing eye and height adjustment via draw spring & spindle * Plastic tool box on right side, enclosed plastic mudguards * Enclosed side underrun protection suitable as advertising space * Rear underrun protection with 2 impact buffers * Foldable "A" sign at the rear for waste disposal * LED tail lights with protective cover * 2 x 7-pin electrical connectors * Chassis hot-dip galvanized (excluding air tanks, axles, drawbar, etc.) * Roller track length approx. 6,950 mm * Locking of the roll-on container using pneumatic 4-point claw system * Front: 2 insertable container stops with 2 additional locking positions * Unladen ride height approx. 1,165 mm * --Permissible gross weight technically possible: 20,000 kg-- * Suitable for container lengths of 5,000 to 7,000 mm * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Immediately available from Egestorf

Stanje: novo, skupna masa: 18.000 kg, največja dovoljena obremenitev: 14.680 kg, konfiguracija osi: 2 osi, Leto izdelave: 2025, * RA-T 18.0 / 018: * Wabco EBS-E (electronic braking system) * TPMS (Tire Pressure Monitoring System) * Emergency release system for spring brake cylinders * Disc brakes * 2 x 11 t Sauer axles * Air suspension (automatically lowers when decoupling the brake) * Drawbar approx. 2,300 mm long with 40 mm towing eye and height adjustment via draw spring & turnbuckle * Plastic toolbox 450 x 470 mm, mounted right side * Side net box 1,000 x 500 x 500 mm * Enclosed plastic mudguards front & rear * Enclosed side underrun protection usable as advertising panel * Rear underrun guard * Rear plastic impact protection buffers * Dangerous goods sign at the rear * 15-pin power connector * LED tail lights * Roller track length approx. 6,830 mm Crodpsv Nulzofx Ad Ueh * Pneumatic 4-point clamp lock * Mechanically adjustable stop brackets (2 positions) front left and right on running rails * 265/70 R 19.5 twin tires * 3,220 kg unladen weight * --Permissible gross weight technically possible: 20,000 kg-- * Approx. 1,130 mm ride height loaded * Suitable for 5,500 - 7,000 mm container lengths * Hot-dip galvanized chassis * Air tanks, axles, slewing ring, and drawbar * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, skupna masa: 11.990 kg, največja dovoljena obremenitev: 8.500 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Oprema: ABS, * KA-TA-R 11.9 Masterline: * Front wall and floor hot-dip galvanized * Wabco ABS * Emergency release device for spring-actuated cylinders * Drum brakes, 2 x 7 t Gigant axles * Parabolic springs with tandem equalizer unit * Height-adjustable (by 300 mm) hot-dip galvanized drawbar with 40 mm flange towing eye * Jost mechanical landing gear at the front * Two mechanical, hot-dip galvanized folding support legs at the rear * 15-pin electrical connector * Multi-chamber tail lamps * Hot-dip galvanized bolted underrun protection * Tool box made of galvanized steel sheet, mounted on right side * Plastic quarter mudguards * Hot-dip galvanized chassis Cjdpfxoq Hg D He Ad Uerh * Steel pallet 3-way tipper body * Continuous white-painted side walls at the top with internal tube reinforcement; foldable without center posts, with drop-side spring assist * Tailgate foldable and swinging, equipped with manual central locking * Hot-dip galvanized bolted rear stakes * Each corner equipped with 1 x 5 t lashing point and each side with 4 x 3 t lashing rings flush-mounted in the outer frame * 4 mm fine grain steel floor plate * Mesh hooks * Rear mounting rail for loading ramps * Removable steel side extensions, 500 mm high, 3 sides, swinging * Body reinforced and certified for load securing according to EN 12642 XL * 1 pair of aluminum drive-on ramps approx. 3,570 x 400 mm (load capacity 8 t per pair), suitable for rubber-tired and tracked vehicles * Rear lockable storage compartment recessed into the chassis below the loading area * Axles, springs, air tanks and landing gear painted in black * Tires 285/70 R 19.5 * Side panel color in RAL 9010 pure white * New vehicle with manufacturer’s warranty * Subject to error and prior sale * Immediately available ex-stock Egestorf, A7

Stanje: novo, skupna masa: 11.900 kg, največja dovoljena obremenitev: 8.850 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2024, * KA-TA-R 11.9 "Masterline": * Floor and front wall hot-dip galvanized * EBS braking system * Emergency release device for spring-loaded cylinders * TPMS Tire pressure monitoring system * Drum brakes * 2 x 5.5 t BPW axles * Parabolic springs with tandem balance unit * Drawbar height-adjustable by 300 mm, with 40 mm flange towing eye * Jost mechanical landing gear front * 2 mechanical, hot-dip galvanized folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * 15-pin electrical connector * LED lighting * Bolted underrun protection * Plastic quarter mudguards * Lashing hooks on the side and rear in the central locking brackets, plus two on the front wall * Steel pallet 3-way tipper body (continuous sidewalls—without center posts—foldable, with sideboard spring assist) * Bolt-on rear stanchions * Combination steel swing doors, rear wall 2-wing, asymmetrically split, 270° pivotable and lockable (not foldable) with additional pendulum frame for automatic tailgate opening during tipping; secured via galvanized rotary rod lock and central locking * Deactivation function for automatic tailgate operation when tipping backwards with open swing doors * In each corner: 1 x 5 t lashing point; on each side: 4 x 3 t lashing rings recessed into the outer frame, 4 mm steel floor plate, rear ramp mounting rail * Reinforced body with load securing certificate according to EN 12642 XL * 1 pair aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles Credpfx Adol Thyxs Ush * Lockable rear storage compartment recessed under the loading platform in chassis * Chassis, drawbar, front wall, tipper bed, rear stanchions, underrun protection, and mechanical drop supports hot-dip galvanized * Side walls and tailgate painted RAL 9010 pure white * Side wall painting in a different RAL color available at extra charge * Axles, springs, coupling eye, air tank, and landing gear painted in black * New vehicle without first registration, with manufacturer's warranty * Subject to error and prior sale * Immediately available ex Egestorf on the A7

Stanje: novo, skupna masa: 14.400 kg, največja dovoljena obremenitev: 12.080 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 3.900 mm, širina tovornega prostora: 1.920 mm, višina nakladalnega prostora: 415 mm, Leto izdelave: 2022, Oprema: ABS, * ETM-TA 14.4: * Wabco ABS braking system * Emergency release device for spring-loaded cylinders * Drum brakes, 2 x 7 t Gigant axles * Parabolic springs with tandem compensating aggregate * Height-adjustable drawbar (+/- 150 mm) with 40 mm screw coupling eye * Jost landing gear at the front, side underrun protection * Foldable A-panel at the rear * 15-pin electrical connector, multi-chamber tail lights * Fixed steel front and side panels * Removable steel rear panel * Floor made of 50 mm softwood * 1 sliding sheet wear plate 750 x 1,000 mm at the front area including 2 removable trough stops at the front, mountable in 2 positions each * 4 removable trough stops, mountable in 2 positions to laterally center the troughs * On each side, 1 x (13.5 t) UVV lashing point for securing tensioning elements Credpfx Ajl Th Eyed Ueh * 2 ratchet tensioners (spindle adjustment) with compensating chain and quick shortening device (tensioning force 6,300 kg) * Rear cross member for attaching aluminum loading ramps including 2 additional support legs at the rear * Loading edge unloaded approx. 710 mm * Chassis, front wall, side walls, mudguards, drawbar, and rear support legs hot-dip galvanized * Axles, springs, landing gear, and air tank painted black * Tyres: 285/70R19.5, wheelbase: 1,140 mm * Loading edge unloaded: approx. 710 mm, sold without container * Color: hot-dip galvanized * Vehicle has a one-day registration in 06/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale reserved * Immediately available ex Egestorf on the A7