Faymonville 3-A-Tiefbett-Pendela.-Bolzen-Laschenkup. nakup rabljenega (64.091)

Stanje: novo, lastna masa: 17.250 kg, največja dovoljena obremenitev: 48.700 kg, skupna masa: 66.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 375 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 17.250 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize loading platform length, approximately 3,750 mm long - Gooseneck hydraulically liftable, lowerable, and detachable - For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Lowbed: - Lowbed with external beams, designed as a telescopic vessel bridge in low-profile construction with front extension - Length x width approx. 7,550 mm x 2,740 mm - Mechanical locking of the extension Chassis: - Rear chassis with closed outer frame - Checker plate surface and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, Suspension, and Tyres: - “PENDEL-AXLE”, all axles hydromechanically forced steered - Burst protection valve on the axle compensation cylinders with automatic reset function - Hydraulic cylinders with shut-off valves and plug pins for securing in raised position - Final coating of axles: two coats of single-color 2-component paint in "FAY-Grey-34-0260" - Technical axle load 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 Accessories: - Detachable steel front wall, approx. 400 mm high - 4 wheel chocks - Rear upper gooseneck area closed with removable cover - 1 pair of steel ramps with climbing bars and locking bolts to bridge the lowbed mounting hooks - Ramps can be positioned over or between the hooks - Mounting options for steel drive-on ramps at the rear, between the outer beams of the gooseneck - Locking point approx. every 1,000 mm on the extension - 1 lashing ring each, left and right, on the front cross member - Supply line connection strip for tractor unit, mounted at the height of outer frame profile - 6 pairs of threaded blocks on the exterior of the load floor inner beams for attaching M24 screw rings - 6 pairs of recessed lashing rings on the outside of the load floor outer beams, foldable inwards and outwards - 1 pair of threaded blocks on the front and rear of the load floor outer beams for M24 screw rings - Mounting rail for loose aluminum approach ramps on the end cross member of the vehicle - Central lubrication system with 2 pumps, brand BEKAMAX - Remote steering front and rear, cable remote controlled, with axle tracking control - 3 kW electro-hydraulic power unit for hydraulic operations, except hydraulic winches - Removable galvanized loading floor, can be placed in 3 elements between the outer beams, with hardwood covering - Foldable extensions, approx. 230 mm per side - Loose extension boards, steel-edged - 4 warning signs approx. 423 x 423 mm - Radio remote control for rear steering - 3.5” kingpin - Anti-slip coating on the left chamfer of the gooseneck - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Guide plate from gooseneck for the fifth wheel plate, approx. 800 mm wide - 1 spare wheel with mounting adapter - Parking position on the gooseneck for warning signs when not in use - 2 pairs of stake pockets integrated into the chassis outer frame, for plug-in stakes approx. 100 x 50 mm Guodpfxsh Hm Tzo Af Rog - Excavator stick trough of rear chassis closed at the rear with a removable plate - Trailer color: Mercedes-Benz 7350 Novagrey

Stanje: novo, lastna masa: 17.500 kg, največja dovoljena obremenitev: 43.500 kg, skupna masa: 61.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.750 mm, višina nakladalnega prostora: 400 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - For tractor units: 6x4 or 8x4 Lowbed: Gjdeh Hm Thspfx Af Rjug - Lowbed with external beams, extendable version, "SUPER LOW" design, approx. 7,550 mm long - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking device - Service lines are protected within the extendable beams and automatically adjust to the lowbed length Rear Undercarriage: - Rear chassis with closed outer frame, checker plate cover, and continuous prism-shaped excavator trough approx. 1,450/900 x 505 mm, open at the rear - 2 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame Axles and Tires: - "PENDULUM AXLE", all axles hydro-mechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 / 3PMSF Included Accessories: - Prepared for bolt-on container positioning for 1x 20ft or 1x 40ft container on the outer beams - 2" kingpin - Galvanized steel front wall approx. 400 mm high - One spare wheel with holder - At the galvanized front adapter bar yellow-red air couplings - 4 wheel chocks - Remote rear steering from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Hydraulic line connections from gooseneck to lowbed with multi-coupling instead of screw coupling - Electro-hydraulic power pack - White reflective tape to EU specifications on sides, extension, and rear red - 2 wooden blocks 500x250x200 mm - European reflective plates (red-yellow) on the trailer rear - At the gooseneck and rear wall left and right each a bracket for warning boards including socket - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 - Load gauge for determination of axle loads including load diagram - On the gooseneck, plug-in ALU side and rear boards approx. 2,000 x 400 mm - The rear galvanized insert posts are removable (body length approx. 2,120 mm) - Separate air connection for air gun on the gooseneck - Duomatic air coupling from gooseneck to lowbed - Rear upper section of gooseneck closed with removable cover - 1 pair of steel ramps to bridge the lowbed's pick-up hooks - Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm - Wireless remote control for rear steering in addition to cable remote, with signal lights at receiver for single-track monitoring - 6 pairs of threaded blocks between lashing rings under the top chord on the outer beams for mounting screwable RUD rings VLBG-4 - 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading bed - Foldable extensions, approx. 230 mm per side - Loading area features a painted sand layer for anti-slip protection - Dipper stick trough of rear chassis closed at front and rear with plug-in plates - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - alu 15%)

Stanje: novo, lastna masa: 12.800 kg, največja dovoljena obremenitev: 36.200 kg, skupna masa: 49.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 375 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 12.800 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimised loading platform length, approx. 3,750 mm in length - Gooseneck can be raised/lowered hydraulically and is detachable - Technical fifth wheel load: 25,000 kg - For tractor units: 4 x 2, 6 x 2, and 6 x 4 Loading platform: - Low-bed with external beams, designed as a telescopic vessel bridge in low-profile construction with front extension - Length 6,850 mm x width 2,540 mm - One locking position approx. every 1,000 mm on the extension Rear running gear: - Rear running gear with closed outer frame featuring checker plate cover and continuous prism excavator recess, approx. 1,250/700 x 505 mm, open at the rear Axles, suspension and tyres: - “PENDLE-AXLE”, all axles force-steered hydro-mechanically - Hose rupture valves on axle equalising cylinders with automatic reset function - Hydraulic cylinders with shut-off valves and pre-locking pins for securing in raised position - Final coat for axles with two layers of 2K acrylic paint, single-colour in “FAY-Grey-34-0260” - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres: 245/70 R 17.5 - TPMS tyre pressure monitoring system in accordance with ECE R 14 Gusdevy Edcopfx Af Rjg - TPMS sensors installed in all wheels, incl. spare wheels Included accessories: - Plug-in steel front wall, approx. 400 mm high - 3 kW electro-hydraulic unit for hydraulic operations, except for hydraulic winches - One spare wheel with mounting adapter - External beams of the gooseneck with mounting holes for bolt-on lashing rings - Plug-in ALU side walls on the gooseneck, approx. 400 mm high, anodised - One plug-in ALU rear wall on the gooseneck, approx. 400 mm high, anodised - Checker plate covering on the gooseneck - Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide - Operating area lighting at the gooseneck with on/off switch - Hydraulic traverse to support the gooseneck on the tractor or a dolly - 2" king pin - Anti-slip stickers on the left chamfer of the gooseneck - The rear upper area of the gooseneck is closed with a removable cover - 4 wheel chocks with holders - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of screw couplings - 1 pair of steel ramps with climbing strips and retaining bolts for bridging the low-bed mounting hooks - The ramps can be placed over or between the hooks - Mounting option for steel drive-on ramps at the rear between the external beams of the gooseneck - Prepared for bolt-on container locks for 1 x 20ft on the external beams - Mechanical pin and lug coupling from low-bed to running gear for exchanging the loading platform or inserting extension beams - With electro-pneumatic-hydraulic couplings - The outer beams of the low-bed are coated with painted-on sand layer as anti-slip protection - Removable (galvanised) load floor, can be inserted in 3 elements between the external beams, with hardwood surface - Foldable extensions, approx. 230 mm per side - Hanging strip at the front of the rear running gear to the low-bed for loose approach ramps - 2 pairs of stake pockets recessed into the outer frame of the running gear, for plug-in stakes approx. 100 x 50 mm - Hanging strip for loose ALU approach ramps at the rear cross member of the vehicle - Central lubrication system with 2 pumps - Radio and cable remote control - 4 extendable warning signs, approx. 423 mm x 423 mm - Numerous lashing positions

Stanje: novo, največja dovoljena obremenitev: 25.300 kg, skupna masa: 38.000 kg, konfiguracija osi: 2 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete range of vehicles, including those available for immediate and short-term delivery, can be found on our website. Excerpt from the equipment specification. Full specification available upon request. Gooseneck * Gooseneck in SNT design to optimize loading area length * Length approx. 3,750 mm, hydraulically lift-/lowerable, as well as detachable * Technical fifth-wheel load: 25,000 kg For tractors: 4 x 2 and 6 x 2 Kessel bridge * Low bed designed as telescopic Kessel bridge SUPER LOW design * Length approx. 6,850 mm * with mechanical locking * Supply lines are routed protectively within the telescopic beams and automatically adjust to the respective low bed length Rear chassis * Short version with closed outer frame and tread plate cover * Chassis with excavator recess, closed in the rear half to accommodate air tanks Axles * BPW axles and suspension, all axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve Tyres * GOODYEAR KMAX T 3PMSF (M+S) 245/70 R 17.5 twinned. Load index 143/141J (146/146F) Brake system * WABCO brand, EBS-E according to EU regulations, WITHOUT connection cable to tractor unit Paintwork * 6-coat final treatment * Complete steel construction shot-blasted after welding * 1 layer of zinc-based primer * 1 layer of adhesion primer. Final coating with 2 layers of 2K (acrylic) paint, single colour, then cavity sealing with special wax Trailer colour * RAL 3002 Carmine red Gusdev Sw E Ajpfx Af Reg * Rim colour: silver-grey * Side wall colour: Aluminium-natural Accessories included * Steel front wall, plug-in, approx. 400 mm high * 3 kW electro-hydraulic pump unit for hydraulic operation, except for hydraulic winches. Without installation of supply connectors at the tractor unit * Mounting adapter for 1 spare wheel in front of the gooseneck front wall * Outer beams of the gooseneck with mounting holes for screwable lashing rings. The first hole approx. 200 mm from the front, then approx. every 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 lashing ring each left and right on the rear chamfer of the gooseneck (LC 6,000 daN) * 2 inch kingpin * Hydraulic traverse for supporting the gooseneck on the tractor or a dolly * Air connection with air pistol on the gooseneck * 1 pair of steel ramps with climbing cleats and retaining bolts to bridge the low bed attachment hooks * 1 lashing ring each left and right on the front cross member (LC 10,000 daN) * At the outer beams of the loading area, prepared for removable loading floor * Lashing rings with retaining spring approx. every 1,200 - 1,300 mm on the inside outer beams of the loading area * Lashing rings with retaining spring approx. every 1,200 - 1,300 mm on the outermost beams of the loading area (LC 10,000 daN) * Cut-outs over the lashing rings on the upper flange of the outer beams * Mechanical pin-lug coupling from the low bed to the running gear, for changing the loading area or installing extension beams. With electro-pneumatic-hydraulic couplings * Outer beams of the low bed with painted-on sand layer for anti-slip protection * 2nd driving height for upper drive position, max. ± 50 mm from the normal driving position, without installation of controls from the tractor unit * 1 pair of lashing rings with retaining spring at the transition from low bed to excavator recess (LC 10,000 daN) * Front and rear chamfered edge

Stanje: novo, največja dovoljena obremenitev: 92.045 kg, skupna masa: 126.000 kg, konfiguracija osi: > 3 osi, Oprema: ABS, Izvleček iz opreme Celotna oprema na zahtevo * 1 x gosi vrat MAX710-Hals-V-30-2.70 * Gosi vrat, hidravlično dvigljiv/spuščljiv in izpodrivljiv * Dolžina približno 3.650 mm. Za SZM 6x4 ali 8x4 Gsdpfxszzhfns Af Reug * Jeklena čelna plošča, približno 400 mm visoka * Na gosi vrat se lahko namestijo aluminijaste bočne stene in zadnja stena, približno 400 mm visoke, v eloksirani izvedbi * 3,5-palčna kraljeva vlečna glava * Hidravlična priključnica za tovornjak z regulatorjem pretoka (20 l/min) * vključno z drogmi za obešanje napajalne linije * rezervoar SZM mora vsebovati vsaj 80 l, z MAX Trailer spojnicami; v nasprotnem primeru stranka zagotovi spojnice * BEKA-MAX centralno mazanje za gosi vrat z normalno maščobo NLGI-2 * TPMS sistem za nadzor tlaka v pnevmatikah, ustrezno * Dve orodjni omari INOX, približno 855 x 340 x 390 mm, na gosi vrat, levo in desno (± 48 kg) * 1-valjni dizelski motor Hatz (Silent Pack) z električnim zagonom in akumulatorjem * Hidravlične povezovalne cevi med hidravlično agregatom in priključno ploščo na gosi vrat * Daljinski upravljalnik: upravljanje hidravlične agregata, vklop/izklop dizelskega motorja * Upravljanje pomožnega krmiljenja, poleg kabelskega daljinskega upravljalnika * z 2 LED kontrolnima lučema na sprejemniku kot sistem za nadzor ene vozne osi * Upravljanje dvigovanja/spuščanja gosi vrata * Upravljanje dvigovanja/spuščanja vzmetenja podvozišč * Multikuplunške hidravlične priključnice na gosi vrat * 1 LED delovna luč levo in desno na zadnji plošči gosi vrat z ločenim stikalom za vklop/izklop * Štiri izpodrivna opozorilna tabla, izpodrivna za približno ± 2 000 mm, približno 423 x 423 mm, z eno LED pozicijsko lučjo in nosilcem za rotacijsko luč (± 122 kg) * 1 x 3-osni kompaktni sprednji podvozišče * MAX710 podvozišče-PA-F-3-19.5-1.36-2.85 * Sprejemnik kavlja spredaj in zadaj * Dolžina: približno 3.560 mm * Širina podvozišča: približno 2.850 mm * Sprednji podvozišče z ločeno zračno priključnico za zračni vijak * BEKA-MAX centralno mazanje za 3-osni podvozišče z normalno maščobo NLGI-2 * Eno 7-polno vtičnico na levi in desni strani zadaj na sprednjem podvozišču za opozorilne table * TPMS sistem za nadzor tlaka v pnevmatikah v skladu z ECE R 1411 * LED delovne luči na levi in desni strani zadaj na sprednjem podvozišču z ločenim stikalom za vklop/izklop * Površina sprednjega podvozišča s premazom peska, nanesenim na metal, za preprečevanje zdrsa * Multikuplunške hidravlične priključnice na sprednjem podvozišču * 1 x most za bager: MAX710-nizko ležišče-BB-A-7.15-(430)-2.85 * Teleskopski most za bager BB-A z nadvoznim mostovnim kavljem spredaj in spojnico s spojkami zadaj * Osnovna širina: približno 2.850 mm, dolžina: približno 7.150 mm * Višina nosilca: približno 430 mm, širina nosilca: približno 1.350 mm * Višina nakladanja približno 580 mm pri oddaljenosti od tal približno 150 mm * 6 parov jeklenih preprog z gumijasto oblogo, približno 1.000 mm, 1 par približno 500 mm (± 1.660 kg) * Možnost privijanja (ø približno 40 mm) na vsakih približno 500 mm zunaj zgornjega pasu zunanje cevi mostu za bager za vijačne obroče (LC 16.000 daN) * Možnost privijanja M30 na vsakih približno 1.000 - 1.200 mm zunaj na notranji cevi mostu za bager za montažo vijačnih obročev (LC 10.000 daN) * Zložljive širitve z jeklenimi preprogami, nastavljive v širino od približno 2.850 mm do približno 3.250 mm * TPMS sistem za nadzor tlaka v pnevmatikah * Par ločenih klinih HeProLen iz plastike z protidrsnimi letevmi, približno 1.200 x 450 x 50/400 mm (± 130 kg) *

Stanje: novo, lastna masa: 34.500 kg, največja dovoljena obremenitev: 106.700 kg, skupna masa: 141.200 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 7.150 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 580 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, obratovalna teža: 34.500 kg, Oprema: ABS, Gooseneck: - Gooseneck hydraulically lift/lowerable as well as detachable - Length approx. 3,650 mm - Extensive lashing positions - For tractor units: 6 x 4 or 8 x 4 3-Axle Compact Front Bogie: - Hook mounts at front and rear - Chassis length x chassis width approx. 3,560 mm x 2,850 mm - Extensive lashing positions Excavator Deck “BB-A”: - Telescopic excavator deck “BB-A” with drive-over deck hooks at the front and bolted lug coupling at the rear - Length x base width approx. 7,150 mm x 2,850 mm - Beam height x beam width approx. 430 mm x 1,350 mm - Loading height 580 mm with 150 mm ground clearance Gusdpfx Afowhywfo Reg - 5 pairs of hanging lashing rings (LC 10,600 daN) - 4 pairs of threaded blocks M30 on inner beam for mounting screw-on rings 5-Axle Rear Bogie: - Mechanical bolt-on lug coupling for fitting a lowbed front, rear end traverse - Chassis length x chassis width approx. 6,840 mm x 2,850 mm - Extensive lashing positions Pendulum Axle and Tyres (front and rear bogie): - “PENDEL-AXLE”, all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-plugs for securing in lifted position - Final paint of axles with 2 coats of 2K paint, single-colour in MB 7350 Novagrau - Technical axle load: 14,640 kg (62 km/h) - Hydraulic axle compensation - Axle tools - Tyres 285/70 R19.5 Steering Override: - Remote steering from the front and rear via cable remote control with push buttons, including axle tracking control - Socket for steering control operation on the gooseneck - Cable remote control with push buttons including axle tracking control Included accessories: - Yellow-red air couplings on galvanised front connection rail - Steel headboard approx. 400 mm high - 4 wheel chocks with holders - 2 spare wheels 285/70 R19.5 - 3.5" kingpin - Gantry with winch for spare wheel at the front side of the gooseneck - Truck hydraulic connection with flow control valve (40 l/min), including gantry for suspension of supply lines, tractor unit tank must be at least 80 litres with couplings - White reflective tape according to EU regulations on sides and extension, red at rear - Plug-in ALU side panels and rear wall on gooseneck, approx. 400 mm high, anodised - Operating lever on gooseneck protected by folding cover - Separate air connection with air pistol on gooseneck - Central lubrication system BEKAMAX with standard grease NLGI-2: 1x on the gooseneck, 1x on 3-axle bogie, 1x on 5-axle bogie - Variomax tool kit - Multi-coupling hydraulic connections in the lowbed hook area - Front bogie with separate air connection for air screwdriver - Threaded inserts (ø 40 mm) every approx. 500 mm on outside of upper flange of excavator deck for screw rings - Folding extensions with steel mats, width adjustable from approx. 2,850 mm to approx. 3,250 mm - Steel mats with rubber covering approx. 12 mm thick - Two INOX toolboxes 855 x 340 x 390 mm - Radio remote control for steering override in addition to cable remote - Painted sand layer as anti-slip measure - 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery

Stanje: novo, največja dovoljena obremenitev: 36.040 kg, skupna masa: 53.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete inventory of immediately and short-term available vehicles can be found on our website. Excerpt from the equipment list. Full specification available on request. Gooseneck: * Gooseneck in SNT design to optimize loading deck length, approx. 3,750 mm long * Gooseneck hydraulically liftable/lowerable and detachable * For tractor units: 6 x 4 or 8 x 4 Lowbed: * Lowbed with exterior beams, extendable, SUPER LOW design, approx. 8,000 mm long * Lowbed with fixed hardwood flooring approx. 40 mm thick and mechanical locking * Supply lines routed protected within the extendable beams, automatically adapting to the lowbed length * 7 pairs of folding lashing rings outward (LC 10,000 daN) * 6 pairs of threaded mounting blocks on the inner beam for screwable RUD rings Rear chassis: * Rear chassis with closed outer frame and tread plate cover * Chassis with excavator recess, closed in the rear half to house air tanks * 3 pairs of folding lashing rings outward (LC 5,000 daN) * 1 pair of folding lashing rings outward (LC 10,000 daN) * 1 pair of horizontal lashing rings, positioned front & rear on the chassis (LC 10,000 daN) Guedpoy Uwu Iofx Af Reg Axles: * BPW axles and suspension, all axles with hydro-mechanical forced steering * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tyres: * Tyres 245/70 R 17.5 3PMSF – manufacturer at choice. Load index (146/146F) Braking system: * WABCO braking system according to EU regulations with EBS-E (2S2M) Coating: * HRM metalizing of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure optimal corrosion protection * Finished with 2 coats of 2K paint, single-colored in RAL 3002 Carmine Red, per RAL System 841GL Includes accessories: * 2-inch kingpin * One galvanized steel front bulkhead, approx. 400 mm high * At the galvanized front connection strip, yellow-red air couplings * Remote axle steering, from front and rear, operated by cable remote control with push buttons, including axle alignment monitoring (without installation on the tractor unit) * Preparation for bolt-on container lockings to accommodate 1 x 20', 1 x 40', or 1 x 45' container on the outer rails. Without container locks * Hydraulic connections from gooseneck to lowbed with a multicoupling instead of screw couplings * Electrohydraulic unit * Spiral cable (approx. 35 mm², approx. 3.5 m in length, max. 250A) for the power supply to the electrohydraulic unit and/or the electric winch, with plug connection (NATO-NATO) between trailer and tractor unit * Yellow reflective tape according to EU regulations, on the sides, extension, and at the rear of the trailer * At the gooseneck front and rear left and right, each with a holder for warning signs, including socket * Manual and documentation on USB stick * Central lubrication system with 2 pumps BEKAMAX (Pico) with standard grease NLGI-2 and removable protection for the pumps * 7 pairs of threaded blocks between the lashing rings under the top flange on the outer rail for mounting screwable RUD rings VLBG-4 * 2nd ride height, approx. 50 mm above standard ride position, selectable via manual control * On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm (L x H). The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) * Separate air connection with air gun on the gooseneck * A stainless steel toolbox, INOX, approx. 1,350 x 400 x 400 mm

Stanje: novo, največja dovoljena obremenitev: 90.700 kg, skupna masa: 126.000 kg, konfiguracija osi: > 3 osi, skupna širina: 2.850 mm, Oprema: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: Hydraulically lift/lower and detachable gooseneck. Length approx. 3,650 mm. Suitable for tractor units: 6x4 or 8x4 Gusdjw Tgp Depfx Af Reg 3-axle compact front bogie: * Hook mounts at front and rear. Length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Lowbed: * ATX-A lowbed with telescopic longitudinal beams in low-profile design, fixed hardwood floor approx. 50 mm thick * With drive-over bridge hooks at the front and bolt-lug coupling at the rear * Base width: approx. 2,850 mm, length: approx. 7,150 mm, beam height: approx. 330 mm, beam width: approx. 750 mm * Loading height approx. 480 mm, ground clearance approx. 150 mm 5-axle rear bogie: * Mechanical bolt-lug coupling for attaching a lowbed at the front; rear end traverse * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * Pendulum axle 3-axle front bogie: * PENDULUM AXLES, all axles hydro-mechanically forced-steered * Hose rupture valve on axle leveling cylinder with automatic RESET function * Hydraulic cylinders with shutoff taps and locking pins for securing in raised position * Final painting of axles with 2 coats of single color 2K paint, painted in MB7350 Novagrau * Rated axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tires for front bogie: 12 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J 5-axle rear bogie: * PENDULUM AXLES, all axles hydro-mechanically forced-steered * Hose rupture valve on axle leveling cylinder with automatic RESET function * Hydraulic cylinders with shutoff taps and locking pins for securing in raised position * Final painting of axles with 2 coats of single color 2K paint, painted in MB7350 Novagrau * Rated axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tires for rear bogie: 20 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimum corrosion protection * Final painting with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, according to RAL-System 841GL Including accessories: * Steel front wall, approx. 400 mm high * Plug-in aluminum side and rear boards on gooseneck, approx. 400 mm high, anodized * 3.5" kingpin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections on gooseneck * Front bogie with separate air connection for air impact wrench * BEKA-MAX central lubrication for one 3-axle bogie * Preparation for bolt-on container positioning for 1 x 20' or 1 x 30' on the outer beams * Without container locks * Brackets on the outer beams for installing foldable extensions * One 7-pin socket left and right, front and rear on rear bogie for warning panels * BEKA-MAX central lubrication for one 5-axle bogie * On the rear bogie, socket for cable remote control for steering * Rear bogie with trough * 2 LED reversing lights mounted on rear panel * European reflector boards (red-yellow) on the rear * One mudflap at rear * One LED beacon with bracket left and right on rear cross-member * Two INOX toolboxes 855 x 340 x 390 mm on gooseneck, left and right * 1-circuit...

Stanje: novo, največja dovoljena obremenitev: 48.300 kg, skupna masa: 71.000 kg, konfiguracija osi: > 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete vehicle inventory, including vehicles available immediately and at short notice, can be found on our website. Below is an excerpt from the equipment list. Full specification available upon request. GOOSENECK: * Gooseneck with integrated single-axle running gear (pendulum axle) in a detachable version * Gooseneck hydraulically liftable and lowerable, including hydraulic connection linked to the hydraulic axle compensation of the first axles Gjdpfx Afjyhkqnj Rjug * Length: approx. 5,200 mm, with front tapering approx. 60° * Fifth wheel load according to data sheet: W25-DSR2700-12/22.7 * For tractor units: 6 x 4 or 8 x 4 * Steel front wall, plug-in type, approx. 400 mm high, with beveled design * 1 pair of mechanical supports at the front of the gooseneck * ASPÖCK-UNIBOX on the front connector panel with 24N, 24S & 15-pin sockets * 1 spare wheel holder inside the front wall of the gooseneck with jib * 2 pairs of recessed lashing rings on the gooseneck (LC 2,500 daN) * 2 pairs of recessed lashing rings on the outer frame of the running gear at the front, foldable outward (LC 10,000 daN) * 1 pair of lashing rings at the transition from running gear to loading platform (LC 10,600 daN) * On the gooseneck 1 pair of removable aluminum drop sides, approx. 400 mm high, anodized * On the gooseneck 1 removable aluminum rear wall, approx. 400 mm high, anodized * 3.5 inch kingpin * TPMS tire pressure monitoring system according to ECE R 141 * Round NATO socket on the front connector panel (Maeler & Kaege VG 96 917) * 1 stainless steel toolbox with 1 lid, mounted on the gooseneck on the right in the direction of travel by the aluminum drop side, approx. 1,350 x 400 x 400 mm (L x W x H) LOADING PLATFORM: * Low-bed with external beams, designed as a telescopic loading platform in low-profile design with front extension including fixed approx. 50 mm thick hardwood floor * Length x width approx. 8,000 mm x 2,740 mm * Mechanical bolt-lug coupling from low-bed to running gear for swapping the loading platform or installing extension beams * One locking position approx. every 500 mm on the extension * 4 pairs of recessed lashing rings fitted flat in the loading platform along the outer frame/external beams (LC 10,000 daN) * 1 lashing ring each on the left and right outer rear cross member (LC 10,000 daN) * Foldable extensions, approx. 230 mm per side (WITHOUT wooden boards) * Loose extension planks, steel-rimmed * Preparation for installation of bolted container positions for 1x 20’ or 1x 40’ container on the outer beams. Without container locks * 6 pairs of threaded blocks between the lashing rings under the top chord of the outer beam for mounting bolted M24 rings (LC 8,000 daN) * 2 pairs M24 bolt rings (LC 8,000 daN) included REAR RUNNING GEAR: * Rear running gear with closed outer frame, checker plate decking and continuous prism-shaped excavator trough, approx. 1,450 x 900 x 505 mm, open at the rear * PENDULUM AXLE, all axles hydro-mechanically forced-steered * Hose rupture valve on axle compensation cylinder with automatic reset function * Hydraulic cylinders with shut-off valves and foreplugs to secure in raised position * Final paint of axles in 2 layers of 2-component paint, single color, DB 7350 Novagrau * Technical axle load: 12,000 kg each * Hydraulic axle compensation * 245/70 R 17.5 3PMSF, brand at our choice * Remote steering from front and rear via cable control, with axle alignment check, no installation in the tractor unit * 4 pairs of hanging la

Stanje: rabljeno, največja dovoljena obremenitev: 44.050 kg, skupna masa: 61.000 kg, konfiguracija osi: 3 osi, prva registracija: 10/2024, naslednji pregled (TÜV): 10/2026, Oprema: ABS, Izvleček opreme Podaljšek (vrat) * zasnovan v stilu SNT za optimizacijo dolžine tovorne površine * dolžina približno 3.750 mm * podaljšek hidravlično dvigljiv/spustljiv in odpenljiv * tehnična obremenitev sedla: 34.000 kg. Za SZM: 6 x 4 ali 8 x 4 (ali 6 x 4 z 1-osnim podvozkom 235/75-17.5) Nizkopodsna prikolica * zasnovana kot teleskopska prikolica za prevoz velikih predmetov, z nizko konstrukcijo * z izvlečnim delom spredaj in mehanskim zaklepom * dolžina x širina približno 7.550 mm x 2.740 mm Zadnje podvozje * z zaprtim zunanjim okvirjem * profilirano jekleno površino in vzdolžno prizmatično žlico za bager, približno 1.450/900 x 505 mm, zadaj odprta Zavorna sistem * znamke WABCO EBS-E, skladno z direktivami EU Osi in vzmetenje * osi PENDEL-AXLE, vse osi hidro-mehansko sinhronizirane * ventil za zaščito pred pretrganjem cevi na cilindru za izravnavo osi z avtomatično funkcijo ponastavitve * tehnična obremenitev osi: 12.000 kg na os * hidravlična izravnava osi Pnevmatike PA * 245/70 R 17.5 3PMSF * indeks obremenitve 143/141L(146/146F) * proizvajalec po naši izbiri Barvanje: * barva nadstavka: RAL 3002 karmin rdeča Priložena dodatna oprema * čelna stena iz jekla, vstavljiva, približno 400 mm visoka * okrogla NATO vtičnica na priključni letev spredaj (Maeler & Kaege VG 96 917) * 3 kW elektro-hidravlična enota za upravljanje hidravličnih sistemov * razen hidravličnih vitlov, zunanji nosilec podaljška z luknjami za pritrditev vijačnih zank * prva luknja približno 200 mm od spredaj, nato približno vsakih 400 mm * 2 para vijačnih zank, priloženih (LC 5.000 daN) * 1 zanka na levi in desni strani zadnje poševnine podaljška (LC 10.000 daN) * nad podaljškom profilirana jeklena površina. * 3,5-palčni kraljevi klin * vodilna plošča podaljška za sedelno ploščo, približno 500 mm široka * hidravlična prečka za podpiranje podaljška na SZM ali podvozkah. * 1 par jeklenih ramp z stopnicami in pritrdilnimi vijaki za premikanje nad prijemne kljuke nizkopodsne prikolice Gjdpjzzudwofx Af Reug * možnost pritrditve jeklenih ramp zadaj med zunanjimi nosilci podaljška. * 1 zanka na levi in desni strani na sprednjem prečnem nosilcu (LC 10.000 daN) * 6 parov navojnih blokov zunaj na notranjih nosilcih tovorne površine za pritrditev vijačnih obročev M24 (LC 8.000 daN). * 2 para vijačnih obročev M24 (LC 8.000 daN), priloženih. * 6 parov vgrajenih zank zunaj na zunanjih nosilcih tovorne površine, z možnostjo zlaganja navznoter in navzven (LC 10.000 daN). * 1 par navojnih blokov spredaj in zadaj na zunanjih nosilcih tovorne površine za pritrditev vijačnih obročev M24 (LC 8.000 daN). * 1 par vijačnih obročev M24 (LC 8.000 daN), priloženih. * priprava za pritrditev vijačnih pritrdilnih elementov za kontejnerje za 1x 20' ali 1x 40' kontejnerje na zunanjih nosilcih. Brez pritrdilnih elementov za kontejnerje. * mehanska zapončna sklopka prikolice za pritrditev na podvozje, za zamenjavo tovorne površine ali vgradnjo podaljševalnih nosilcev. * z elektro-pneumatično-hidravličnimi spojkami * vtična letva spredaj na zadnjem podvozju za prikolico za pritrjevanje odlagalnih ramp * 4 pari zank, obešenih v zunanjem okvirju zadnjega podvozja (LC 10.000 daN) * 1 par zank, nameščenih spredaj v prijemni žlici zadnjega podvozja (LC 16.000 daN) * 1 par zank, nameščenih v prijemni žlici v območju 2. osi zadnjega podvozja (LC 16.000 daN) * 1 par zank, nameščenih zadaj v prijemni žlici zadnjega podvozja (LC 10.000 daN) * 2 para žepov za drog v zunanjem okvirju podvozja, vgrajenih.

Stanje: novo, lastna masa: 12.900 kg, največja dovoljena obremenitev: 34.100 kg, skupna masa: 47.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 350 mm, vzmetenje: drugo, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 12.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm in length - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2, and 6x4 Loading Platform: - Low-bed with external beams, extendable “SUPER LOW” design, approx. 6,850 mm in length - Low-bed with fixed hardwood flooring, approx. 40 mm thick, with mechanical locking device Rear Chassis: - Rear chassis with closed outer frame, chequer plate covering, and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings, foldable to the outside - 1 pair of lashing rings recessed in the trough - 2 pairs of stake pockets for insertable stakes 100 x 50 mm in the external frame Pendulum Axle and Tyres: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and safety locking pins for securing in raised position - Axles painted with two layers of single-colour 2K paint in “FAY-Grey-34-0260” - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 - TPMS tyre pressure monitoring system according to ECE R 141 Accessories: - Preparation for the installation of bolt-on container locators for 1 x 20ft or 1 x 40ft container on the outer girders - 2" king pin - One galvanized steel front wall, approx. 400 mm high - One spare wheel - Yellow-red air couplers on the galvanized front connection bar - 4 wheel chocks - Remote steering from front and rear, operable via wired remote control with push buttons, with single-track alignment control - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of screw couplings - Electro-hydraulic power unit - White reflective tape in accordance with EU regulations on sides, extension, and rear - European reflective plates (red-yellow) on the rear of the trailer - One bracket on each side of gooseneck and rear plate for warning panels, including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on outer beam for mounting screw-on RUD Rings VLBG-4 - Detachable ALU side boards and rear board on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized insertable stakes are removable (body length approx. 2,560 mm) - Gooseneck rear upper area covered with removable cover - 5 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading area - Folding extensions, approx. 230 mm per side - 2 pairs of bolted RUD Rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the mounting hooks of the low-bed - Anti-skid sand layer painted on loading surface - 80 km/h speed stickers at rear and both sides - Spoon boom trough at rear chassis closed at rear with plug-in plate - Four extendable warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for rear axle steering in addition to cable remote, with indicator lights on receiver for alignment control - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard NLGI-2 grease - Load pressure gauge for determining axle loads - HRM Metallisation (High Resistance Metallisation) of outer frame Gedpfxehlz R So Af Rsug - Complete steel structure shot blasted, then all defined visible areas metallized and finished with ZINACOR 850 (zinc 85% - aluminium 15%) hot galvanizing

Stanje: novo, skupna masa: 78.000 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 850 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck in SNT design to optimize loading area length, approx. 3,700 mm long, rear with a bevel approx. 1,000 mm x 10° • For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading Area: • Extendable loading platform, approx. 8,800 mm long with rear bevel approx. 500 mm x 10° • A recess in the platform and rear bevel to accommodate the excavator dipper stick, approx. 3,950 x 580 x 370/450 mm Ramps: • One pair of two-piece steel ramps, approx. 4,350 mm long and 900 mm wide • Hydraulically folding ramp tips • Ramps hydraulically adjustable separately approx. 235 mm outwards and approx. 215 mm inwards • Hardwood decking on the beveled part of the loading area • Ramp with hardwood decking • 20 x 30 mm square climbing strips, approx. every 200 mm on the outer frame of the ramp Axles and Tyres: • TWINAXLE-II independent wheel suspension with BPW stub axles, 1st axle steered in advance, all other axles are hydromechanically forced steered • 1st axle with electromagnetic reverse lock via reverse gear and manual activation • Technical axle load: 12,000 kg • Hydr. axle compensation, hydraulic cylinders with shut-off valves • Tyres 245/70 R 17.5 • TPMS tyre pressure monitoring system according to ECE R 141 Accessories Included: • Plug-in steel front wall, approx. 400 mm high • 4 wheel chocks with holder • Front connection bar with yellow-red air couplings • 3 kW electro-hydraulic power pack for hydraulic control, except for hydraulic winches • 1 spare wheel • 2 pairs of screw-in lashing rings • 1 pair of horizontal lashing rings in the rear area of the gooseneck • On the gooseneck: 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized • On the gooseneck: 1 plug-in ALU rear board, approx. 400 mm high, anodized • Approx. 40 mm thick hardwood decking on the gooseneck, checker plate over the king pin • 3.5" king pin • Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide • Load area locking with conically welded arresting profiles every 250 mm • Incl. pre-tensioning plate Gsdpforvw U Sox Af Reug • 1 pair of lashing rings on the front cross member • 8 pairs of recessed, fold-out lashing rings in the outer frame of the platform • Extendable (galvanized) widenings approx. 230 mm per side • 1 pair of fixed open wheel recesses up to extension, approx. 700 x 410 mm, in the platform in front of the 1st axle • Wheel recesses with checker plate covering and 15 x 15 mm square climbing strips, approx. every 200 mm • 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm, in the platform between the 1st and 2nd axle • Wheel recesses with 15 x 15 mm square climbing strips and widenings in the lower section • ALU covers for the wheel recesses between 1st and 2nd axle, which can also be used as broadening planks • 1 pair of mechanical rear supports • 20 x 30 mm square climbing strips, approx. every 200 mm on the outer frame of the bevel of the loading area • Central lubrication system with 1 pump, BEKAMAX brand, standard grease as per NLGI-2 • Radio and cable remote control, with 2 indicator lights on the receiver for single wheel control • WABCO Smart Board system • The Smart Board is equipped with an odometer • 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and mounts for rotating beacon

Stanje: rabljeno, skupna masa: 133.000 kg, konfiguracija osi: > 3 osi, prva registracija: 11/2023, Oprema: ABS, Trailer - Vehicle Identification Number: XNJ55H5XX23H01262 - First registration: 29.11.2023 DOLLY - Vehicle Identification Number: XNJ33H5XD23H01262 - First registration: 29.11.2023 POWER HYDRAULICS with NATO socket – or machine hydraulics German registration Unladen weight: Trailer: 27,140 kg | DOLLY: 13,200 kg Fifth wheel height: 1,350 mm – Replaceable kingpin – 3.5" Front swing clearance approx. 1,732 mm ---- Hydraulic, detachable and height-adjustable swan neck – Length 4,020 mm Lowbed: Length: 8,000 mm Width: 2,870 mm – Loading height: approx. 560 mm TELESCOPIC extension by 5,800 mm EXPANDABLE up to 3,240 mm Chassis frame: Length: 7,410 mm Width: 2,750 mm – Loading height: approx. 1,100 mm Total length with dolly: 24,622 mm / without dolly: 20,140 mm Excavator trough - dipper stick recess Central lubrication system BROSHUIS axles – PENDLE AXLES with drum brakes Guedpfxjx Ialvj Af Reg with radio remote control 5 x hydraulically suspended and forced-steered axles Axle loads: 5 x 12,000 kg Maximum fifth wheel load: 25,000 kg Tyres: 285/70 R 19.5 – Tread depth approx. 10 mm throughout Matching 3-axle DOLLY Hydraulically suspended axles Modifications, prior sale, and errors expressly reserved. The description serves for general vehicle identification and does not constitute a guarantee in the legal sense. The contractual vehicle specification is binding. Our offer is generally without new TÜV inspection. If a new TÜV inspection is desired, we are happy to provide an offer from our partner workshops! The vehicle may be covered with advertising stickers and/or decals. Our general terms of delivery and payment apply.

Stanje: rabljeno, skupna masa: 61.000 kg, konfiguracija osi: 3 osi, prva registracija: 08/2010, Oprema: ABS, Polpriklopnik - številka šasije: W09PG3009A0M49815 - Prva registracija: 25.08.2010 DOLLY - številka šasije: W09PG3009A0M49816 - Prva registracija: 25.08.2010 ELEKTRO-HIDRAVLIKA Nemški tehnični pregled (DE HU) zapade Lastna teža: Polpriklopnik: 16.850 kg -- DOLLY: 2.240 kg Višina priklopa: 1.280 mm - zamenljiv kraljevi zatič - 3,5" Obračalni krog spredaj cca 1.640 mm ---- hidravlično spuščajoč in po višini nastavljiv labodji vrat - dolžina 3.750 mm Globoko ležišče: dolžina: 6.850 mm, širina 2.750 mm - nakladalna višina: cca 350 mm TELESKOPSKO podaljšljivo za 4.000 mm RAZŠIRLJIVO do 3.210 mm Gusdpfx Afswxi Nrs Rsg Podvozje: dolžina: 4.100 mm, širina: 2.750 mm - nakladalna višina: cca 1.035 mm Skupna dolžina: 14.700 mm Baggerska zajemalka - vdolbina za ročico Centralni sistem mazanja GIGANT osi - NIHALNE OSI z bobnastimi zavorami z daljinskim upravljanjem 3 x hidravlično vzmetene in prisilno vodene osi Nosilnosti osi: 3 x 12.000 kg Največja nosilnost priklopa: 25.000 kg Pnevmatike: 245/70 R 17,5 ustrezen DOLLY z 1 osjo BPW Eco os z bobnasto zavoro Zračno vzmetenje Pridržujemo si pravico do sprememb, predhodne prodaje in napak. Opis služi splošni identifikaciji vozila in ne predstavlja jamstva v pravnem smislu prodaje. Pravno zavezujoč je izključno opis v kupoprodajni pogodbi. Naša ponudba je praviloma brez novega TÜV pregleda. Če želite novo TÜV potrdilo, vam z veseljem pripravimo ponudbo naših partnerskih servisov! Vozilo je lahko polepljeno ali označeno z oglaševanjem. Uporabljajo se naši splošni dobavni in plačilni pogoji.

Stanje: novo, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.700 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 890 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimizing loading area length, approx. 3,700 mm long, with rear tapering of approx. 1,000 mm x 6° - For tractor units: 4 x 2 and 6 x 2 Loading platform: - Loading platform, approx. 9,700 mm long, with hydraulically foldable and lowerable rear section as well as hydraulically liftable front section for driving onto the gooseneck Axles and tyres: - BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle self-steering - 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually - Technical axle load: 12,000 kg - Air suspension with lift/lower valve - 235/75 R 17.5 3PMSF twin tyres - TPMS tyre pressure monitoring system according to ECE R 141 BPW Auto Reverse Control: - Electrohydraulic auxiliary steering for the self-steering axle of a 3-axle unit - Automatic control of the self-steering axle when reversing via gyroscope sensor - Manual steering operation in forward and reverse using separate radio remote control - Manual operation enabled up to 10 km/h - System powered by separate electro-hydraulic unit Accessories included: - Removable steel front wall, approx. 400 mm high - 3 kW electro-hydraulic power pack Godeyw Sakepfx Af Rsug - External beams on gooseneck with mounting holes for bolted lashing rings - First mounting hole approx. 200 mm from front, then approx. every 400 mm - One mounting hole at upper rear of external gooseneck beams for a bolted lashing ring - Grating cover with 5 mm sheet reinforcement on gooseneck and rear taper - 2" king pin - Guide plate on gooseneck for fifth wheel plate, approx. 500 mm wide - Round NATO socket at front connection bar (Maeler & Kaege VG 96 917) - 1 pair of removable side aluminium drop sides on gooseneck, approx. 400 mm high, anodized - 4 wheel chocks - Electric winch, approx. 5,400 kg pulling force, with radio remote control - Wire cable approx. 24 m long, cable ø approx. 9.5 mm, including cable pressure roller - Winch installed at the front inside the gooseneck - Continuous grating cover with 5 mm steel underlay for additional reinforcement, designed for point loads: - on the lift bed - on the loading platform - on the hydraulically lowerable rear section - Painted-on sand coating on the gooseneck covering plates and in transition areas between neck and lift bed, between lift bed and loading platform, and between loading platform and ramps - 1 spare wheel - Hydraulic lift bed, approx. 2,500 mm long, load capacity while driving in raised position: 9,000 kg - Hydraulic cylinders are fitted with load-holding valves - Cut-outs in the outer frame of the loading platform and lift bed for attaching tension straps - Extensive lashing positions - Hydraulically lowerable rear section for loading and unloading, can be raised to shorten total coupling length - Load capacity while driving in horizontal position: 10,000 kg - Shortening of total coupling length when raised: 2,350 mm - Painted-on sand coating on the complete ramp, except for the extendable galvanized part of the ramp - Hydraulically extendable rear extensions for loading and unloading - Radio remote control: - Control of hydraulic lift bed - Control of hydraulic lifting of rear extension - Control of hydraulic extension of rear extension - 1st axle with starting aid - Centralized lubrication system with 1 pump - 4 warning signs, approx. 423 x 423 mm, extendable

Stanje: novo, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.700 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 890 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimal load deck length, length approx. 3,700 mm, rear end with chamfer approx. 1,000 mm x 6° - For tractor units: 4 x 2 and 6 x 2 Load deck: - Load deck, approx. 9,700 mm long with hydraulically folding and lowering rear section, as well as hydraulically liftable deck at the front for driving over the gooseneck Axles and Tyres: - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle steering on trailing arm - 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manual switch - Technical axle load: 12,000 kg - Air suspension with lifting and lowering valve - 235/75 R 17.5 3PMSF twin tyres - TPMS tyre pressure monitoring system compliant with ECE R 141 Included accessories: - Plug-in steel front wall approx. 400 mm high - Yellow-red air couplings on the front connection rail - 3 kW electro-hydraulic power pack for control of hydraulic functions, except hydraulic winches - Outer beams on the gooseneck with fixing holes for screwable lashing rings - First hole approx. 200 mm from front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - One mounting hole on the upper rear area of the outer beams of the gooseneck for a screwable lashing ring - On gooseneck and rear chamfer, grating covering with 5 mm plate reinforcement - 2" kingpin - Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide - Round NATO socket on the front connection rail (Maeler & Kaege VG 96 917) - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodised - 4 wheel chocks - Electric cable winch, approx. 5,400 kg pulling force, with remote control - Wire rope approx. 24 m long, rope diameter approx. 9.5 mm, incl. rope pressure roller - Winch mounted at the front inside of the gooseneck - Plastic tarpaulin cover for the winch Guedpfsyw R Srjx Af Reg - Mechanical landing gear with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - Continuous grating covering with 5 mm plate reinforcement for additional strength, designed for point loads: - on the lifting bed - on the load deck - on the hydraulically lowerable rear section - Painted-on sand coating on the gooseneck covers and transitional areas between neck and lift bed, between lift bed and load deck, and between load deck and ramps - 1 spare wheel with mounting adapter under the load deck on the right in front of the axles - Hydraulic lifting bed, length approx. 2,500 mm, load capacity in driving position (raised): 9,000 kg - Hydraulic cylinders fitted with load-holding valves - Cut-outs in the outer frame of the load deck and lifting bed for lashing straps - Extensive lashing positions - Hydraulically lowerable rear section for loading/unloading and can be raised to reduce overall train length - Load capacity in driving position (horizontal): 10,000 kg - Reduction of overall train length when raised: 2,350 mm - Painted-on sand coating on the entire ramp, except for the extendable galvanised ramp section - Hydraulic, extendable rear extensions for loading and unloading - Remote control: - Lifting bed operation - Lifting device for rear extension operation - Extension of rear extension operation - 1st axle with traction aid - Central lubrication system with 1 pump - 4 warning boards, approx. 423 x 423 mm, extendable

Stanje: novo, lastna masa: 10.300 kg, največja dovoljena obremenitev: 39.200 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Platform: - Loading platform after the gooseneck, hydraulically liftable and lowerable, length approx. 2,800 mm, with rear chamfer approx. 1,000 mm x 8° - Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, over the axles with chequer plate covering Two-part Steel Ramps: - One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp parts, hydraulic lifting system, and hydraulically adjustable - Maximum load per pair: 40,000 kg Axles, Suspension and Tires: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated by reverse gear and manually Gujdpfx Aeu Hp Href Rsg - Air suspension with lift and lower valve - Axle tool - Tires 235/75 R 17.5 3PMSF - TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories Included: - One spare wheel with holder in front of the bulkhead - 2" kingpin - One galvanized steel front wall approx. 400 mm high - Yellow-red air couplings at the galvanized connection strip in front - 4 wheel chocks - Galvanized folding supports under the platform's rear chamfer - A holder for a rotating beacon at the rear of the trailer - Cover plates to bridge the gap between ramps and platform - White reflective tape as per EU regulations along the sides of the trailer and red at the rear - Electro-hydraulic unit at the rear, under the platform - At the gooseneck and at the ramps left and right, each with a holder for warning signs, including socket - Control valves for the ramps positioned on the right side of the trailer - European reflective plates (red-yellow) at the rear of the trailer - Manual and description on USB stick - Removable ALU side walls and rear wall on the gooseneck approx. 2,440 x 400 mm - The rear, galvanized side stakes are removable (body length approx. 2,560 mm) - An electric cable winch with radio remote control, approx. 5,400 kg lifting force, including 9.5 mm steel cable, 24 m long, with guide roller - Bolted 5 t ring for cable deflection of the winch on the gooseneck without pulley - 2 pairs WADER container pockets in the platform for a 20ft container - 6 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the platform - Lift axle on the front axle with control via TEBS E, depending on actual axle load and loading condition - 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN) - 1 pair of recessed lashing rings along the central beam at the rear chamfer (LC 10,000 daN) - Sand coating for slip resistance painted on the chequer plates on the gooseneck and on the platform - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and removable pump protection - Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm - Speed stickers 80 km/h rear and on both sides - Load manometer for determining axle loads including load chart - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then all defined visible surfaces metallized and hot-coated with ZINACOR 850 (zinc 85% - alu 15%)

Stanje: novo, lastna masa: 14.350 kg, največja dovoljena obremenitev: 53.450 kg, skupna masa: 67.800 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, dvižna zadnja plošča, Gooseneck: - Gooseneck in SNT design for optimization of loading bed length, length approx. 3,700 mm - Gooseneck rear with chamfer approx. 1,000 mm x 10° Godpfx Afoya E A Ns Rsug - For tractor units: 6x2, 6x4, 8x4 short Loading bed: - Extendable loading bed, length approx. 8,800 mm, rear chamfer approx. 500 mm x 10° - A recess in the loading bed and the chamfered section for receiving the excavator dipper stick, approx. 3,850 x 750 x 210/290 mm Two-part steel ramps: - One pair of two-part steel ramps, length approx. 4,350 mm, width approx. 900 mm - Ramps with rubber covering - Ramps hydraulically adjustable individually approx. 235 mm outwards and approx. 215 mm inwards - 'Super Grip' 25 mm rubber flooring and approx. 5 mm steel plate as additional reinforcement on the rear chamfer of the loading bed - Square climbing bars 20 x 30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: - BPW axles and suspension, 1st axle steering, all other axles hydromechanically forced-steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Tires 235/75 R 17.5 - TPMS tire monitoring system according to ECE R141 - TPMS tire sensors fitted on all wheels, including spares Surface treatment: - Complete steel structure automatically blasted with shot blasting system after welding - Second blasting with corundum for optimum coating adhesion - HRM metallization of entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for best corrosion protection - Final painting with 2 layers of 2K top coat, single colour in MB 7350 Novagrau Accessories included: - Plug-in steel front wall, approx. 400 mm high - 3kW electro-hydraulic power unit for controlling hydraulic functions, with the exception of hydraulic winches - 1 spare wheel - Outer carrier on the gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings in the rear area of the gooseneck - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized - On the gooseneck, 1 plug-in ALU rear board, approx. 400 mm high, anodized - On top of the gooseneck, approx. 40 mm thick hardwood flooring, above kingpin area with checker plate cover - 2" kingpin - Round NATO socket on front connection strip - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front cross member - 8 pairs of recessed, fold-out lashing rings in the outer frame of the loading bed - Extendable (galvanized) widenings by approx. 230 mm per side - Wheel recesses with square climbing bars, 15 x 15 mm, in front of the axles fully open up to gooseneck cross beam, approx. 700 x 410 mm - Wheel recesses with square climbing bars, 15 x 15 mm, between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - ALU covers for wheel recesses, which can also be used as bridging elements for the extension or as widening boards - 1 pair mechanical rear supports - Radio and cable remote control - Lift axle on front axle - Square climbing bars 20 x 30 mm, approx. every 200 mm - Central lubrication system with 1 pump - Wabco Smart Board system - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: rabljeno, lastna masa: 19.880 kg, največja dovoljena obremenitev: 40.120 kg, skupna masa: 60.000 kg, konfiguracija osi: > 3 osi, prva registracija: 03/2021, dolžina tovornega prostora: 7.700 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 350 mm, velikost pnevmatike: 245/70 R 17,5, barva: siv, Leto izdelave: 2021, Oprema: ABS, Šasija: - Varjena konstrukcija iz jeklenega okvirja s sprednjim in zadnjim upognjenim okvirjem ter ravno nizkopodno platformo brez naklona - Sprednji vogali poševno odrezani 400 mm x 400 mm - Nizkopodložje z dvema izvlečnima okvirjema, izvlečna dolžina cca 5.400 mm, 1x 400 in nato po 500 mm, pnevmatsko zaklepanje - Zaklep pri 1.833 mm za 30 ft kontejner - Zaklep pri 4.900 mm za 40 ft kontejner - Premišljena vmesna podpora širine cca 500 mm, uporablja se le pri teleskopiranju vozila (v zloženi različici brez vmesne podpore) - Sedelna plošča z zamenljivim 2'' in 3,5'' kraljevim čepom - Maksimalna točkovna obremenitev: 50 t na 4 m v zloženem stanju - Neprekinjena izkopna kad nad osnim agregatom s preklopnim aluminijastim pokrovom - 2 zaklenljiva pokrova, vsak dolžine 1.500 mm. Zadnji del s fiksnim aluminijastim pokrovom za elektro-hidravliko in centralni sistem mazanja - Mehanska spojka z zatiči na zadnjem delu nizkopodložja za vnaprejšnjo napetost v podu Labodji vrat: - Hidravlično spuščajoči in po višini nastavljiv labodji vrat - Naslon na vlačilcu poteka preko dveh hidravličnih valjev. Upravljanje preko elektro-hidravlične enote - Priklop na labodjem vratu v kombinirani izvedbi za priklop nizkopodne nakladalne površine in reduktorskega agregata - Labodji vrat s preklopom za različne pritiske na sedlo (18/24 t) Osovine, krmiljenje in pnevmatika: - Gigant nizkopodne polosovine, vsaka 12 t nosilnosti - Hidravlično vzmetenje, dvig cca 300 mm, višina vožnje nastavljiva hidravlično - S-cam zavore 300/150 mm, zavorne obloge brez azbesta - Avtomatski nastavljalci zavor t - Širina tira 1.995 mm, razdalja med osmi 1.510 / 1.510 mm - Krmilna ročica za vzmetenje levo + desno zadaj - 1. os (reduktorski agregat) hidravlično prisilno vodena preko sedelne sklopke - 2., 3. in 4. os hidravlično prisilno vodene preko sedelne sklopke in osi krmilne z glavo - Elektrohidravlično naknadno krmiljenje preko elektroagregata spuščenega labodjega vratu s napajanjem iz vlečnega vozila preko NATO vtičnice - Krmilni kabel in vtičnica spredaj in zadaj na zaključni plošči - Daljinsko upravljanje s kablom ter dodatno brezžično daljinsko upravljanje - Gume 13 / 17 245/70 R 17.5 146/146F, brez zračnic Reduktorski agregat: - Enosna, lahko se namesti med labodji vrat in nizkopodložje - Polosovina s 12 t nosilnosti, hidravlično vzmetenje - 4-kratno oplaščene pnevmatike - Zavorne cevi preko priključnih glav, hidravlične cevi preko šestkratne multi-spojke - Osovina z blokirnim ventilom in vstavnim zatičem za dvigovanje Gedpfszd Tdzex Af Roug Dodatna oprema: - Sprednja stena = škatla za orodje iz jeklene pločevine, visoka 600 mm, globoka 550 mm, preko celotne širine z zgornjim pokrovom ter stransko levo + desno - Vogali spredaj prilagojeni poševnini - Bočne stene iz 25 mm aluminijastih votlih profilov, višina 600 mm, enodelne, do 500 mm pred nizkopodložjem, zložljive - Vstavljena aluminijasta zadnja stena ter vstavljivi zadnji vogalni stebri v višini bočne stene - Dolg nosilec registrske tablice na zaključni plošči - 2 ECE opozorilni tabli na zaključni plošči - 3 para vgrajenih pritrdilnih obročev na visoki platformi, vsak z vlečno silo 4 t, ca. 1.500 mm od spredaj montirani - 3 para težko-tovorstnih pritrdilnih obročev z vlečno silo po 13,4 t, od tega - 1 par visi na visoki platformi, vsak 1 par na srednjem delu visoke postelje spredaj in zadaj na naklonjenem vzdolžnem nosilcu - Zložljive razširitve obeh strani v nizkopodložju na skupno širino 3.000 mm - Izvlečne opozorilne table, brezstopenjsko

Stanje: rabljeno, največja dovoljena obremenitev: 34.400 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, prva registracija: 12/2007, Dolžina podvozja (Swanenhals): približno 3.500 mm Polmer upogiba: 2.300 mm za triosno prikolico Največja dovoljena obremenitev sedla: 18.000 kg Guedpfszzu Eujx Af Reg Višina sedla pri natovorjeni prikolici: približno 1.140 - 1.350 mm Višinska nastavitev s pomočjo dvižne vzmetne ročice spredaj: približno -280 / +250 mm Dolžina nosilne površine: približno 9.500 mm Širina nosilne površine: približno 1.560 mm Hidravlično vzmetenje zadnje osi Osnova BPW z ABS Posamično vzmetenje koles, hidravlična izravnava osi z dvižno in spuščalno napravo. Vsako os lahko dvignemo posamično. Centralni sistem za mazanje z 1 črpalko, BEKAMAX Aluminijaste stranske ograje na podvozju, približno 400 mm visoke 3 pari hidravličnih zatičev za pritrditev tovora.

Stanje: rabljeno, skupna masa: 50.100 kg, konfiguracija osi: 3 osi, prva registracija: 01/2020, dolžina tovornega prostora: 13.500 mm, širina tovornega prostora: 2.500 mm, skupna širina: 2.540 mm, skupna višina: 3.380 mm, Oprema: ABS, Številka vozila: YAMT23XX3K0104337 TELESKOPSKA PODALJŠANJE za 7.300 mm NOSILCI ZA KONTEJNERJE WADER za 1 x 20", 2 x 20", 1 x 40", s podaljškom za 45-palčni kontejner DE HU 09.2026 - SP 03.2027 Os SAF z bobnastimi zavorami 3 x osi s prisilnim krmiljenjem, hidravlično-mehansko, s kabelskim upravljanjem + daljinskim upravljanjem Mere platforme: 13.500 mm (od tega 500 mm poševno) - višina nakladanja: 1.100 mm Nosilna palica za dvižne rampe (BREZ ramp) Višina sedla: 950 - 1.050 mm Polmer obračanja nazaj: 2.100 mm Žepi za podpore na dnu, vključno s podporami (ni zagotovljeno, da so vse prisotne) NATO vtičnica – elektro-hidravlična agregatna enota Osvetlitev za razširitev Orodjarna Centralno mazanje Pnevmatike: 235/75 R 17,5 Nosilec za rezervno kolo SREDI rezervno kolo Guedpfxszn Drwo Af Rjg Pridržujemo si pravico do sprememb, medprodaje in napak. Opis služi za splošno identifikacijo vozila in ne predstavlja garancije v pravnem smislu. Odločilni so pogoji, navedeni v pogodbi o nakupu. Naša ponudba na splošno ne vključuje novega tehničnega pregleda. Če je nov tehnični pregled zaželen, vam bomo z veseljem posredovali ponudbo naših partnerskih servisov! Vozilo je lahko oblepljeno z reklamami in/ali označeno. Veljajo naši splošni pogoji dostave in plačila.

Stanje: rabljeno, skupna masa: 51.600 kg, konfiguracija osi: 3 osi, prva registracija: 05/2019, dolžina tovornega prostora: 13.620 mm, širina tovornega prostora: 2.540 mm, skupna širina: 2.540 mm, skupna višina: 2.700 mm, Oprema: ABS, Številka identifikacije vozila: YAFSR3004K0022661 TELESKOPSKO podaljšanje do 8.200 mm Pripravljene tirnice za aluminijaste rampe, BREZ ramp Priprave za pritrditev kontejnerjev: 1 x 20", 2 x 20", 1 x 40", za kontejnerje dolžine 45" DE HU 01.2027 – naslednji pregled SAF osi s kolutnimi zavorami 3 x osi s prisilnim krmiljenjem, hidravlično-mehansko na vrtljivi platformi s kabelskim upravljanjem in radijskim daljinskim upravljanjem Samodejno usmerjanje DVIŽNA OS Mere platforme: 13.600 mm – višina nakladalne površine: 1.100 mm Višina sedla: 980 mm Polmer gibanja zadnje osi: 2.100 mm Gedpfx Aozlvtnsf Reug Vdolbine za nosilce na dnu, vključno z nosilci (ni zagotovljena popolnost) NATO vtičnica Elektro-hidravlična enota Osvetlitev za širjenje Orodjarna Centralni sistem za mazanje Pnevmatike: 235/75 R 17,5 Nosilec za rezervno kolo, VKLJUČNO z rezervnim kolesom Pridržujemo si pravico do sprememb, medprodaje in napak. Opis služi za splošno identifikacijo vozila in ne predstavlja garancije v smislu zakona o prodaji. Odločilni so pogoji, navedeni v pogodbi o prodaji. Naša ponudba na splošno ne vključuje novega tehničnega pregleda. Če je nov tehnični pregled zaželen, vam z veseljem pripravimo ponudbo naših partnerskih servisov! Vozilo je lahko opremljeno z reklamnimi nalepkami in/ali oznakami. Veljajo naši splošni pogoji dobave in plačila.

Stanje: rabljeno, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 03/2018, dolžina tovornega prostora: 13.500 mm, širina tovornega prostora: 2.540 mm, skupna dolžina: 13.750 mm, skupna širina: 2.540 mm, Oprema: ABS, Številka vozila: YAFSR3003J0021354 Guedpfxszp S Eze Af Rsg TELESKOPSKA podaljšitev do 8.200 mm NOSILCI ZA KONTEJNERJE WADER za 1 x 20", 2 x 20", 1 x 40", v izvlečnem delu za 45-palčne kontejnerje DE HU 05.2027 - SP 11.2026 Os SAF z bobnasto zavoro 3 vodene osi s hidravlično-mehanskim sistemom na vrtljivi platformi z upravljanjem s kablom in radijskim daljinskim upravljanjem Samodejno usmerjanje Dimenzije platforme: 13.500 mm – višina nakladalnega prostora: 1.100 mm Višina sedelne sklopke: 950 – 1.050 mm Polmer obračanja v zadnji smeri: 2.100 mm Reže za nosilce v podu, vključno z nosilci (popolnost ni zagotovljena) NATO vtičnica Elektrohidravlična agregatna enota Osvetlitev za širitev Orodjarna Centralni sistem za mazanje Pnevmatike: 235/75 R 17,5 Nosilec za rezervno kolo SREDI rezervno kolo Pridržujemo si pravico do sprememb, prodaje in napak. Opis služi splošni identifikaciji vozila in ne predstavlja garancije v smislu pogodbe o nakupu. Odločilni so pogoji, navedeni v pogodbi o nakupu. Naša ponudba na splošno ne vključuje novega tehničnega pregleda. Če je nov tehnični pregled zaželen, vam bomo z veseljem pripravili ponudbo naših partnerskih servisov! Vozilo je lahko obdelano z reklamnimi nalepkami in/ali napisom. Veljajo naši splošni pogoji dobave in plačila.

Stanje: novo, največja dovoljena obremenitev: 50.400 kg, skupna masa: 65.000 kg, konfiguracija osi: > 3 osi, Oprema: ABS, Celoten seznam naših vozil, ki so na voljo takoj ali v kratkem času, najdete na naši spletni strani. Izbor iz opreme. Popolna oprema na zahtevo. GOOSENECK (Prikolice s gooseneck prikolico) Gooseneck prikolica v obliki SNT za optimizacijo dolžine nakladalne površine, dolžina približno 3.700 mm, zadaj s poševnim robom približno 1.000 mm x 10°. Za SZM (posebna vozila): 4 x 2, 6 x 2 in 6 x 4. - Sprednja stena iz jekla, vstavljiva, približno 400 mm visoka - Električno-hidravlična agregat 3 kW za upravljanje hidravličnih funkcij, razen hidravličnih vitlov. - Na gooseneck prikolici 1 par vstavljivih aluminijastih stranskih ograj, približno 400 mm visoke, v anodizirani izvedbi. - Na gooseneck prikolici 1 vstavljiva aluminijasta zadnja stena, približno 400 mm visoka, v anodizirani izvedbi. - 2 palčni kraljevi zatič - Nosilec na zadnjem delu gooseneck prikolice za aluminijaste nagibne rampe. - Okrogla NATO vtičnica na priključni letev spredaj (Maeler & Kaege VG 96 917) NAKLADALNA POVRŠINA Nakladalna površina v izvlečni izvedbi, dolžina približno 8.800 mm, s poševnim robom zadaj, približno 500 mm x 10°. Globina v nakladalni površini in v poševnem robu za namestitev žlice bagra, približno 3.850 x 750 x 210/290 mm (D x Š x V). Guedpotx Nwnofx Af Reg Pnevmatsko zaklepanje s koničnim zaklepnim vijakom in ojačanimi položaji za zaklepanje, napajalne linije so zaščitene v izvlečnih nosilcih in se samodejno prilagajajo dolžini nakladalne površine. - Sistem za nadzor tlaka v pnevmatikah (TPMS) v skladu s standardom ECE R 141. - Osnova BPW in vzmetenje, 1. os je vodilno sklopna, vse druge osi so hidro-mehanično prisilno sklopne. - 1. os z elektromagnetično zaporo za vzvratno vožnjo, aktivira se preko vzvratne prestave in ročno. - Tehnična nosilnost osi: 12.000 kg na os. - Zračno vzmetenje z ventilom za dvig in spuščanje. - Pnevmatike 245/70 R 17.5 3PMSF, dvojne pnevmatike. Izbira proizvajalca. - Zaklepanje nakladalne površine s konično privarjenimi profili za zaklepanje, približno vsakih 250 mm. - 1 vmesna miza, približno 300 mm široka, za izvlečno cev s velikim prečnim prerezom. - Podaljški (pocinkani), izvlečni približno 230 mm na stran (brez lesenih plošč). - Žlebovi za pnevmatike s kvadratnimi rebrastimi profilimi, približno 15 x 15 mm pred osmi, neprekinjeno odprti do prečnega nosilca gooseneck prikolice, približno 700 x 410 mm (Š x G). - Žlebovi za pnevmatike s kvadratnimi rebrastimi profilimi, približno 15 x 15 mm med 1. in 2. osjo, približno 1.480 x 700 x 410 mm (D x Š x G). - Upravljalni ventili za hidravlične rampe na desni strani vozila. - Upravljanje z zadnje in sprednje strani s kabelskim daljinskim upravljalnikom, z nadzorom smeri osi, brez vgradnje v SZM. HIDRAVLIČNE NAKLADALNE RAMPE DR-15/60-900-4350-KG-HV-M Par dvodelnih jeklenih ramp s dolžino približno 4.350 mm in širino približno 900 mm. Površina večjega dela rampe je razdeljena na dva dela: - Pločevinasta površina s kvadratnimi rebrastimi profili približno 15 x 30 mm, približno vsakih 200 mm zunaj, in gumijasta površina notri. - Hidravlično razširljive konice rampe, rampe so posamično hidravlično premikajoče približno 235 mm navzven in približno 215 mm navznoter. - Največja obremenitev in nakloni skladni s tehničnimi podatki: C465501 - Gumijasta podlaga Super Grip, približno 25 mm in ploščata podlaga, približno 5 mm, kot dodatna ojačitev na poševnem robu nakladalne površine. ZAVORNI SISTEM Zavorni sistem proizvajalca WABCO EBS-E v skladu s predpisi EU. Brez priključnega kabla za traktor. OSVETLITVENI SIS

Stanje: rabljeno, konfiguracija osi: 3 osi, prva registracija: 01/2012, skupna dolžina: 13.700 mm, skupna širina: 2.550 mm, skupna višina: 3.300 mm, vzmetenje: zrak, velikost pnevmatike: 245/70 R17.5, barva: drugo, Leto izdelave: 2012, Oprema: ABS, = Additional Options and Accessories = - Drum brakes = Remarks = Chassis Diameter of kingpin / fifth wheel: 2 inch Gjdpfxsx U D Alo Af Reug Height of kingpin / drawbar: 120 cm Drum brake: ✓ Special transport 2-piece road plates: ✓ Hydraulic ramps: ✓ Length over axles: 900 cm Platform length: 900 cm Gooseneck length: 360 cm Maximum width: 290 cm (250+20+20) Extendable: × = Further Information = Axle configuration Tire size: 245/70 R17.5 Axle brand: SAF Brakes: Drum brakes Suspension: Air suspension Front axle: Twin tires; Tire tread left inside: 40%; Tire tread right inside: 25% Middle axle: Twin tires; Tire tread left inside: 50%; Tire tread right inside: 40% Rear axle: Twin tires; Tire tread left inside: 15%; Tire tread right inside: 25% Weights Unladen weight: 11,000 kg Payload: 37,000 kg Gross vehicle weight: 48,000 kg Identification Registration number: C340521 = Company Information = For more information on this unit please call: or e-mail: . A full stock overview can be found at: . Please do not forget to subscribe to our newsletter for weekly updates on our stock.