Müller-Mitteltal Samooskrba 3 Strani nakup rabljenega (252)

Stanje: novo, največja dovoljena obremenitev: 31.900 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release for spring-actuated cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lift/lowering function and RtR valve ----Drawbar: * Straight drawbar with 50 mm towing eye and continuously adjustable height ----Electrics / Lighting: * Tire pressure monitoring system with display option in truck dashboard via EBS signal – no installation required on truck * SmartBoard as infotool with pressure sensors for axle load display per axle group * 15-pin power connector * LED taillights * Removable LED beacon at rear ----General attachments: * Warning plates front & rear * 2 x toolboxes made of galvanized, powder-coated sheet steel approx. 650 x 300 x 600 mm, right side * Closed single plastic mudguards at front * Straight steel spray suppression panels at rear, each with spray suppression * Side underrun protection ----Low-bed platform: * Turntable/platform extension by 520 mm with 45° corners and 3 recessed storage compartments incl. lids and lockable * Flooring on turntable platform made of 50 mm softwood; on low-bed platform made of 60 mm softwood * 20 mm rubber covering instead of timber in drive lane area with a well length of 6,780 mm including sloped ramp * Rubber coating on the ramp left and right, approx. 860 mm length * 4 stake pockets per side (stakes not included) with simultaneous 2 t lashing point capability ----Chassis: * Chassis made of high-strength fine-grain steel ----Load securing (Lasi package): Turntable/platform: * 2 pairs of 13.4 t lashing eyes in outer frame of turntable/platform Low-bed: * 4 pairs of 10 t lashing rings per side on the outer frame, foldable and loadable in all directions * 2 pairs of 13.4 t swiveling lashing rings at rear on each side ----Ramps: * Rubber covering on foldable access ramps * Hydraulic folding ramps with hydraulic tip extension approx. 4,650 x 720 mm * Hydraulically lateral ramp shift & load-holding valves ----Rear support: * Hydraulic rear support ----Widening: * 8 pairs of galvanized folding outriggers for 3 m overall width (not on rear bevel) * Widening boards stowed on left side compartment ----Excavator boom trough: * Excavator boom trough above rear axle to end of slope approx. L=2,100 mm x W=740 x D=190 mm * 2 pairs of 6.4 t lashing rings at sides in excavator trough ----Hydraulics: Nwjdeylfvmopfx Af Aec * Hydraulic flow divider in trailer (for truck hydraulic pump outlet above 40 up to max. 120 ltr./min.) ----Loading dimensions: * Rear loading platform: approx. 6,780 x 2,520 mm (incl. 860 mm ramp) * Platform above turntable: approx. 2,990 x 2,520 mm ----Loading height: * Loaded approx. 890 mm, +/- 20 mm ----Paintwork: * Reflective contour tape at sides and rear * Chassis, turntable, access ramps and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks and turntable painted in black tone ----Info: * New vehicle with manufacturer warranty * Errors and prior sale reserved * Sample images may show special equipment ----Lead time: * Vehicle available from approx. week 23/2026

Stanje: novo, največja dovoljena obremenitev: 13.490 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, TRA-Kombi 18.0: 3-in-1 = for hook-lift containers, skip containers, and as a low loader ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 10.5 t axles ----Suspension: * Air suspension with manual lowering at rear ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm towing eye and height adjustment ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System), display possible in the truck via EBS signal (no truck-side installation required) * LED tail lights 12 / 24 V * 15-pin electrical connector ----General Attachments: * Tool box made of powder-coated sheet steel * Spare wheel holder in basket design on the right side * Closed side underrun protection * Plastic 1/4 mudguards with splash protection * Plastic rear impact bumpers * Foldable "A" sign rear plate ----Loading Area: * Hot-dip galvanized main frame with raised outer frame for guiding rolling containers * Steel sheet floor with roll recesses in the bogie area * For hook-lift container transport: container length from 5,500 to 7,000 mm possible * Pneumatic 4-point locker and mechanically plug-in front stops in the runway * Transport of up to 2 skip containers with max. 10 m³ volume possible * Includes 8 repositionable container stops for lateral centering, front 4 stops with swiveling shackle * Weld bead as anti-slip surface in the inclined entry area * Mechanical rear landing supports ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning devices for positive and force-fit securing, with 4 cloverleaf-style lashing brackets on each side * 1 pair of 13.4 t UVV lashing rings at the front * On each side, 4 x 8 t lashing eyes recessed into the outer frame ----Ramps: * Aluminium approach ramps (10.6 t / pair), 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable rear storage compartment) ----Paintwork: * Reflective contour tape on sides and rear * Frame hot-dip galvanized * Axles and drawbar painted black ----Info: Nedpfjl Tld Iox Af Aewc * Load securing certificate according to DIN 30722-1 * Load securing certificates according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * --Permissible total gross weight technically possible: 20,000 kg-- * New vehicle with factory warranty, no initial registration * Errors and prior sale excepted ----Delivery time: * Available immediately ex Egstorf

Stanje: novo, največja dovoljena obremenitev: 31.900 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, T 4 Profi 40.0 ----Brake System: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lifting and lowering system and RtR valve ----Drawbar: * Straight drawbar with 50 mm towing eye and stepless height adjustment ----Electrics / Lighting: * Tire pressure monitoring system with display capability in the truck display via EBS signal – no truck-side installation required * SmartBoard infotool with pressure sensors for axle load display by axle group * 15-pin power connector * LED taillights * Removable rear LED rotating beacon ----General Attachments: * Warning sign package front & rear * 2 x toolboxes made of galvanized (powder-coated) sheet steel, approx. 650 x 300 x 600 mm, mounted right-hand side * Closed single plastic fender at the front * Straight rear steel mudguards with spray protection (anti-spray mist) * Side underrun protection ----Low Loader Deck: * Turntable platform extension by 520 mm with 45° corners and 3 recessed storage compartments including lockable lids * Floor over turntable platform made of 50 mm and on the low loader platform of 60 mm softwood * 20 mm rubber flooring in the running area instead of wooden floor, with a recessed bed length of 6,780 mm including the ramp slope * Rubber flooring on ramp slope left and right, approx. 860 mm long * Four stake pockets per side (stakes not included), each with 2 t lashing capability ----Chassis: * Chassis made of high-strength fine-grained steel ----Load Securing (Lashing Package): Turntable Platform: * 2 pairs of 13.4 t lashing rings on the outer frame of the turntable platform Recessed Bed: * Four pairs of 10 t folding and multi-directional lashing rings per side on the outer frame * Two pairs of 13.4 t swivel lashing rings each at the rear left and right ----Ramps: * Rubber covering on foldable ramps * Hydraulic folding ramps with hydraulically extendable tip, approx. 4,650 x 720 mm * Hydraulic lateral ramp adjustment & load-holding valves ----Rear Support: * Hydraulic rear support ----Widening: * 8 pairs of galvanized folding outriggers for 3 m total width (not at the rear slope) * Widening planks stored in a side compartment on the left ----Dipper Stick Rest: * Dipper stick rest over rear axle to end of ramp slope, approx. L=2,100 mm x W=740 x D=190 mm * 2 pairs of 6.4 t lashing rings on the sides of the dipper stick rest ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump output from the truck over 40 – max. 120 l/min) ----Loading Dimensions: * Rear cargo area: approx. 6,780 x 2,520 mm (incl. 860 mm ramp slope) * Area above turntable: approx. 2,990 x 2,520 mm ----Loading Height: * Loaded approx. 890 mm, +/- 20 mm ----Paintwork: * Reflective contour tape on sides and rear Nwsdpfx Afoylfvgj Ajc * Chassis, turntable, ramps, and outriggers hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in black ----Info: * New vehicle with manufacturer warranty * Subject to errors and prior sale * Sample images may include special equipment ----Delivery Time: * Vehicle available from approx. week 23/2026

Stanje: novo, največja dovoljena obremenitev: 13.490 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, TRA-Kombi 18.0: * 3-in-1 solution: suitable for roll-off containers, skip containers, and as a low-loader ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: Nodewb Rakopfx Af Aswc * 2 x 10.5 t axles ----Suspension: * Air suspension with manual lowering at the rear ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long with 40 mm towing eye and height adjustment device ----Electrical / Lighting: * Tire pressure monitoring system (TPMS), display capability in truck via EBS signal (no truck-side installation required) * LED rear lights 12/24 V * 15-pin power connector ----General Attachments: * Tool box made of powder-coated sheet steel * Spare wheel carrier (basket type) on the right side * Closed side underrun protection * Plastic quarter mudguards with splash protection * Plastic rear impact protection buffers * Foldable A-sign at the rear ----Loading Platform: * Hot-dip galvanized main frame with raised outer frame for guiding roll containers * Steel deck with recessed rollers in the bogie area * Can transport roll-off containers with a container length of 5,500 – 7,000 mm * Pneumatic 4-point clamp locking and mechanical plug-in stop angles at the front of the guide track * Transport of up to 2 skip containers with a max. volume of 10 m³ possible * Includes 8 repositionable bin stops for lateral centering of the skips, front 4 stops plug-in with pivoting stop * Weld bead as anti-slip coating in the ramp area of the track * Mechanical drop-down supports at the rear ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the side for securing with tensioning elements, 4 cloverleaf-type lashing brackets per side * 1 pair of 13.4 t UVV lashing rings to the front * 4 x 8 t recessed lashing eyes per side in the outer frame ----Ramps: * Aluminum loading ramps (10.6 t/pair) 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Paintwork: * Reflective contour tape on sides and rear * Frame hot-dip galvanized * Axles and drawbar painted black ----Additional Information: * Load securing certificate according to DIN 30722-1 * Load securing certificates according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * --Permissible gross weight of 20,000 kg technically possible-- * New vehicle without initial registration, with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available from Egstorf

Stanje: novo, največja dovoljena obremenitev: 13.490 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, TRA-Kombi 18.0: 3 in 1 = suitable for hooklift containers, skip containers, and as a low-bed trailer ----Braking System: * EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10.5 t axles Nwsdpfol Tnwzex Af Aec ----Suspension: * Air suspension with manual rear lowering ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm tow eye and height adjustment device ----Electrical / Lighting: * TPMS (Tire Pressure Monitoring System), display capability in the truck via EBS signal (no truck-side installation required) * LED tail lights, 12 / 24 V * 15-pin power connector ----General Attachments: * Tool box made of powder-coated sheet steel * Spare wheel holder, basket design, right side * Enclosed side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear impact protection buffer * Folding A-sign at the rear ----Loading Platform: * Hot-dip galvanized main frame with raised outer frame to guide roll-off containers * Steel sheet floor with roller recesses in the bogie area * When transporting roll-off containers: container length from 5,500 - 7,000 mm possible * Pneumatic 4-point container locking system and mechanically lockable stop angles at the front of the track * Transport of up to 2 skip containers with max. 10 m³ capacity possible * Includes 8 repositionable skip stops for lateral centering, the front 4 are plug-in with pendulum-mounted stops * Weld bead as anti-slip surface in the inclined ramp area * Mechanical rear drop supports ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning elements for positive and non-positive securing of skips, 4 lashing brackets each (shamrock design) on the sides * 1 pair of 13.4 t UVV lashing rings forward * 4 x 8 t lashing eyes recessed in the outer frame on each side ----Ramps: * Aluminum loading ramps (10.6 t / pair) 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Painting: * Reflective contour markings, sides & rear * Frame hot-dip galvanized * Axles, drawbar painted black ----Information: * Load securing certificate according to DIN 30722-1 * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 * --Permissible gross weight of 20,000 kg technically possible-- * New vehicle without initial registration, with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex Egstorf

Stanje: novo, največja dovoljena obremenitev: 10.900 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, ETÜ-TA-R 14.4 ----Braking System: * EBS Electronic Braking System * Emergency release mechanism for spring-loaded cylinders * Drum brakes Nwodopk Dv Repfx Af Aec ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Air suspension ----Tow Bar / Flange Towing Eye: * Height-adjustable tow bar, adjustable by 300 mm * Tow bar extension by 250 mm to a total of 2,250 mm * 40 mm flange towing eye ----Lighting / Electrics: * Tire pressure monitoring system (TPMS) * LED rear lights 12 / 24 V * 15-pin power connector ----General Attachments: * Jost landing gear at the front * Externally mounted hot-dip galvanized folding supports at the rear * Plastic toolbox on the front right side of the headboard * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood floor * Preparation in front of the headboard for retrofitting container locks * Bolted headboard made of smooth sheet metal * Trapezoidal profiled drop-side walls made of steel, foldable with drop-side spring assist * Steel rear wall insertable between ramp mounts; when not in use, stowed inside in front of the headboard * Bolt-on rear posts * Rear approach angle approx. 860 mm ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Possible installation of 3 t drop lashing rings every 600 mm * One 6.3 t lashing point in each front and rear corner * Various holes in the front and rear cross member for 1.2 t lashing options ----Ramps: * One-piece mechanical grid ramps with spring assistance for single-person operation, approx. 2,750 x 600 mm (can be telescoped down to 20 mm) ----Painting: * Hot-dip galvanized chassis as well as tow bar, headboard, rear wall, tailgate, and ramps * Side wall color RAL 9010 pure white * Painting of side walls in a RAL color of choice available at extra cost ----Information: * --Reinforced and certified body according to EN 12642 XL incl. load securing certificate-- * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Available immediately ex works Egestorf

Stanje: rabljeno, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 02/2021, naslednji pregled (TÜV): 08/2026, dolžina tovornega prostora: 4.800 mm, širina tovornega prostora: 2.430 mm, višina nakladalnega prostora: 500 mm, Oprema: ABS, Müller-Mitteltal nizkopodni kesonski priklopnik Nedpfx Ajyk Rfkjf Aewc - Nizkopodni in dvosmerni kesonski priklopnik v enem vozilu - Vlečno uho 40 mm - Pnevmatski zavorni sistem - Podporna stojala za nakladanje in razkladanje - Gigant osi - Pnevmatske gume: 235/75 R 17,5 - Bobnaste zavore - Lastna teža: 3.620 kg - Nastavljiva višina drogov - TÜV veljaven do: 08.2026 - SP veljaven do: 02.2026 - SP veljaven do: - Dolžina tovornega prostora: 4.800 mm - Širina tovornega prostora: 2.430 mm - Višina stranic: 0,5 m Pridržujemo si pravico do napak in vmesne prodaje. Interna številka vozila: 11349.

Stanje: novo, največja dovoljena obremenitev: 38.900 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, T5 Profile 50.0: ----Brakes: * Wabco EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (driving height +30 mm when lifted) * Last axle is steering-locked (lockable from the driver’s cab for maneuvering purposes without truck-side installation, additional control via switch on trailer); lock must be disengaged before driving on public roads * Forced lifting and lowering of lift axle for maneuvering purposes (truck-side installation required) with speed-dependent activation via EBS electronics ----Suspension: * Air suspension, raising and lowering system with RtR valve ----Drawbar: Drawbar 1,500 mm long with 50 mm towing eye and manual height adjustment ----Electrics / Lighting: * Smartboard as info tool, with pressure sensors for individual axle load display per axle group * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) * LED lighting system 12/24V * LED beacon (removable) at rear ----General Fittings: * Mechanical warning sign kit for 3 m overall width * Tool box, galvanized steel sheet, approx. 650 x 300 x 600 mm, mounted on left side * Plastic mudguards front axle, galvanized steel mudflaps rear axle ----Lowbed Deck: * Turntable extension at front with 45° corners and 3 storage compartments with lockable, rear-folding lids * Shortening of the lowbed deck by 500 mm to 6,280 mm including extended offset step of 500 mm to the front * Rubber coating on tipping frame, approach slope, as well as on the running surface of the low loader deck * Bamboo wood between the main beams in front of excavator boom rest ----Load Securing (LaSi Package): * 2 x 6.4 t lashing rings at the front corners * Side, front and rear, each 2 x 13.4 t UVV lashing rings at the corners * Side, each side 5 x 10 t UVV lashing rings (swiveling and lowerable, loadable in all directions) * Side, 4 stake pockets each with simultaneous 2 t lashing capability * 1 x 16 t UVV lashing ring on the rear cross member ----Widening: * Extendable and foldable widening outriggers for 3 m total width (plank holders under chassis, right side) ----Excavator Stick Rest: * Continuous stick rest with reinforcement profile from final axle to end beam approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings laterally in the stick rest ----Ramps: * Hydraulic folding ramp with dual-line hydraulics and adjustable tip section, approx. 4,650 x 720 mm, incl. load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (for hydraulic pump output in the truck of over 40 l/min up to max. 140 l/min) ----Loading Height: Nedol Tihuopfx Af Aswc * Loaded: 890 mm +/- 20 mm by air suspension ----Loading Area Dimensions: * Platform over turntable: 2,600 + 390 x 2,520 mm * Lowbed deck: 6,280 + 500 x 2,520 mm, incl. 860 mm approach slope ----Paintwork: * Chassis, turntable, drawbar, widening brackets, loading ramps galvanised * Drawbar, axles, hydraulic axle supports, and air tanks painted black ----Info: * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: Available from KW

Stanje: novo, največja dovoljena obremenitev: 38.900 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, T5 Profile 50.0: ----Braking System: * WABCO EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (ride height +30 mm when axle is lifted) * Last axle with trailing steering (locking of trailing axle for maneuvering possible from the cab without truck-side installation, as well as additionally via a switch on the trailer); lock must be deactivated before driving on public roads * Forced lift and lowering of the lift axle for maneuvering purposes (truck-side installation required) with speed-dependent control via EBS electronics ----Suspension: * Air suspension, raising and lowering system with RtR-valve ----Drawbar: * Drawbar 1,500 mm long with 50 mm towing eye and manual height adjustment ----Electrics / Lighting: * Smartboard as information tool with pressure sensors for axle load display per axle group * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation necessary) * LED light system 12 / 24 V * Removable LED beacon at the rear ----General Attachments: * Mechanical warning sign package for 3 m overall width * Toolbox made of galvanized steel approx. 650 x 300 x 600 mm, mounted left side * Front-axle plastic fenders and galvanized steel mudguards at rear axle ----Low Loader Deck: * Extension head of the turntable platform with 45° corners and 3 storage compartments with lockable folding lids (folding lids open to the rear) * Shortening of the low loader platform by 500 mm to 6,280 mm incl. extended offset cranking by 500 mm forward * Rubber covering on folding frame, drive-on ramp, and platform running surface * Bamboo timber between the longitudinal beams in front of the digger arm support ----Load Securing (LaSi Package): * 2 x 6.4 t lashing rings at the front corners * On each side, front and rear corners: 2 x 13.4 t UVV lashing points * Additionally, 5 x 10 t UVV lashing rings per side (pivoting and lowerable, loadable in all directions) * 4 stake pockets per side, each with simultaneous 2 t lashing capability * 1 x 16 t UVV lashing ring on the rear traverse ----Widening: * Extendable and folding width extensions for 3 m overall width (beam holders under the chassis, right side) ----Digger Arm Support: * Continuous digger arm trough with reinforcement profile from last axle to rear crossmember approx. L=2,350 x W=770 x D=270 mm, 2 pairs of 6.4 t UVV lashing rings on the sides ----Ramps: * Hydraulic folding ramp with dual-circuit hydraulics and fold-out tip section, approx. 4,650 x 720 mm, including load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (for truck-side hydraulic pump output over 40 l/min up to max. 140 l/min) ----Loading Height: * Loaded 890 mm +/- 20 mm via air suspension ----Platform Dimensions: * Platform above slewing ring: 2,600 + 390 x 2,520 mm * Low-bed platform: 6,280 + 500 x 2,520 mm, incl. 860 mm drive-on slope ----Paintwork: * Chassis, turntable, drawbar, widening consoles, access ramps hot-dip galvanized * Drawbar yoke, axles, hydraulic axle supports, and air tanks painted in a black tone ----Information: * New vehicle with manufacturer's warranty * Subject to prior sale and errors ----Delivery Time: Nedjxptn Depfx Af Aswc * Available from KW

Stanje: novo, največja dovoljena obremenitev: 29.850 kg, skupna masa: 38.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 8.000 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, TS 2 ML ----Brakes: * EBS-E (electronic braking system) * Emergency release mechanism for spring brake cylinders Nodpfeykx I Hsx Af Aowc * Drum brakes ----Axles: * 2 x 10 t axles * Last axle is a trailing steering axle with electro-pneumatic steering lock, activated by PIN in reverse gear * Additional lock for the trailing axle operated from the tractor unit for shunting purposes – no installation necessary on the truck side – assigned to PIN 10; the lock must be deactivated before driving on public roads ----Suspension: * Air suspension with raise and lower function and Ride-on-Road (RtR) feature ----Electrics / Lighting: * Tire pressure monitoring system with display option in the truck's display via EBS signal – no truck-side installation required * LED tail lights 12 / 24 V * Flashing side marker lights * LED reversing lights activated via reverse gear * SmartBoard installed as an info tool with pressure sensors exclusively for total axle load display * 7-pin socket at the rear for extended-length lighting * LED beacon (removable) at the rear ----General Attachments: * Aluminum air tanks * Mechanical crank landing legs * Galvanised sheet steel mudguards * Swivel arm as carrier for connecting lines in front of the front panel ----Warning Package: * Mechanically adjustable warning sign package ----Low Loader Platform: * 50 mm floor covering made from larch / Douglas fir instead of spruce / fir * Rear bevel – 700 mm long – on the semi-trailer platform to the low-bed section with checker plate covering, and at the end a perforated strip for attaching aluminum approach ramps * Tread plate covers over the wheels * SP combo package: toolbox with 45° corners made from galvanized sheet steel, additionally powder-coated in RAL 9006 white aluminum, located on the semi-trailer platform approx. 2,480 x 500 mm * Folding lid on top as well as side doors in the angled corners * Foldable aluminum side boards 500 mm high on the semi-trailer platform, including foldable and removable rear stanchions * Inserted aluminum rear wall, 150 mm high * Second kingpin position * Preparation for container locking * Preparation for 3 recesses in the approach bevel from the low-bed to the gooseneck * Preparation for retrofitting folding outriggers for 3 m widening by welding the mounting brackets into the outer frame ----Load Securing: Semi-trailer platform: * In the front corners and front, 50 mm drilled holes for 1.2 t lashing force per hole * 2 x 16.5 t lashing rings recessed in the floor on the sides towards the approach slope * Perforated outer frame, 45° folded with hole pattern for lashing points (2 t lashing points every 480 mm) * On each side, 2 x 6.3 t retractable lashing rings recessed in the outer frame Low-bed platform: * 2 x 16.5 t lashing rings centrally positioned directly in front of the approach ramp to the gooseneck and recessed * On each side, 3 pairs of 13.5 t lashing rings and 5 pairs of 10 t lashing rings recessed in the outer frame * On each side, 4 stake pockets recessed in the outer frame * Profifix lashing rail in the center along the longitudinal axis (lashing capacity 3 t per lashing circuit) ----Excavator Arm Rest: * From the end of the last rigid axle to the rear crossmember, W = 770 mm, D = 270 mm (on each side, 2 x 6.4 t lashing rings solid welded in the excavator arm rest) ----Ramp: * Hydraulic one-piece "ALLTEC" aluminum approach ramps, approx. 3,200 x 750 mm * Load capacity 13 t per ramp (load capacity 26 t/pair) * Hydraulic ramp

Stanje: novo, največja dovoljena obremenitev: 29.850 kg, skupna masa: 38.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 8.000 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, TS 2 ML ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10 t axles * Rear axle as trailing steering axle with electro-pneumatic steering lock via reverse gear PIN * Additional trailing axle lock, operable from the cab for maneuvering purposes – no truck-side installation required – assigned to PIN 10; lock must be disengaged before driving on public roads ----Suspension: * Air suspension with lift and lowering function as well as RtR function ----Electrics / Lighting: * Tire pressure monitoring system with display option in truck instrument cluster via EBS signal – no truck-side installation required * LED rear lights 12 / 24 V * Flashing side marker lights * LED reverse lights, activated via reverse gear * SmartBoard mounted as an infotool with pressure sensors exclusively for total axle load indication * 7-pin socket at the rear for overlength lighting * Removable LED beacon at the rear ----General Attachments: * Aluminum air tanks * Mechanical crank landing gears * Galvanized steel mudguards * Swivel arm as a carrier for connection cables in front of the front bulkhead ----Warning System Package: * Mechanically adjustable warning sign package ----Low Loader Platform: * 50 mm flooring made of larch / Douglas fir instead of spruce / fir Nedsykx I Tspfx Af Aswc * Rear inclined section – 700 mm long – on the saddle platform to the low-bed with checker plate surface and at the end a perforated strip for hanging aluminum loading ramps * Tread plate covers above the wheels * SP-Combo Package: Tool box with 45° corners, made of galvanized steel and additionally powder-coated in RAL 9006 white aluminum, on the saddle platform approx. 2,480 x 500 mm * Hinged lid on top and side doors in the slanted corners * Fold-down aluminum side walls, 500 mm high, on the saddle platform, including rear stakes, foldable and removable * Inserted aluminum rear wall, 150 mm high * 2nd kingpin position * Prepared for container locks * Prepared for 3 mounting shafts in the inclined section from the low-bed to the gooseneck * Prepared for retrofitting fold-out supports for 3 m extension by welding in receptacles on the outer frame ----Load Securing: Saddle Platform: * Front corners and forward 50 mm bores for 1.2 t lashing force per hole * 2 x 16.5 t lashing rings recessed in the floor towards the inclined ramp * Perforated outer frame, 45° angled with hole pattern for tie-downs (2 t lashing points every 480 mm) * Each side with 2 x 6.3 t retractable lashing rings recessed in the outer frame Low Loader Platform: * 2 x 16.5 t lashing rings centered directly before the inclined section to the gooseneck, recessed * Each side with 3 pairs 13.5 t and 5 pairs 10 t retractable lashing rings recessed into the outer frame * Each side with 4 stake pockets recessed in the outer frame * Profifix lashing rail centered in the longitudinal axis (lashing capacity 3 t per lashing circuit) ----Excavator Arm Rest: * From end of last rigid axle to end crossmember W = 770 mm, D = 270 mm (each side with 2 x 6.4 t lashing rings permanently welded into the excavator arm rest) ----Ramp: * Hydraulic one-piece “ALLTEC” aluminum ramps approx. 3,200 x 750 mm * Load capacity 13 t per ramp (26 t per set) * Hydraulic ramp shifting on sliding tube for ramp shaft ----Hydraulics: * Hydraulic flow divider in the trailer (for lorry hydraulic pump output exceeding 40 l/min up to max. 250 l/min), climbing strips on t

Stanje: novo, največja dovoljena obremenitev: 14.600 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, * Müller Mitteltal ETÜ-TA-R 19 Flatbed Low Loader – Tandem Trailer with Ramps * NEW VEHICLE, no initial registration, available again soon (please pre-order) * Leasing, financing, trade-in, and free delivery to your yard available ---- Inquiry No. 18615 (sample photos) * Gross weight: 19 t, Payload: 14.60 t * Front wall bolted, made of smooth sheet metal (hot-dip galvanized) * Bolted rear stanchions (hot-dip galvanized) * Floor made of 50 mm thick softwood, 6.27 m x 2.47 m * Front mounting option for retrofitting container locks * Load securing package: * 4 UVV lashing rings LC 8000 daN, installed according to existing hole pattern in the 45° outer frame, recessed in the cross member front and rear * 2 pairs LC 10,000 daN, recessed and foldable in the cross member at front and rear * Perforated outer frame (45° angled with pattern for lashings), lashing capacity per point LC 2000 daN at minimum spacing of 480 mm * Additional 10 UVV lashing brackets (LC 3000 daN), recessed in the existing hole pattern in the outer frame * Further lashing points via boreholes (Ø 50 mm, LC 1,200 daN) in the front and end cross member * Toolbox in front of the front wall included * Ramps: one-piece, with hot-dip galvanized grating surface, non-slip design * 2 UVV folding supports at the rear * LED lighting * 2 additional LED reversing lights at the rear Nwsdpfx Afoykgm Rs Asc * Flashing LED side marker lights * Chassis and drawbar (hot-dip galvanized) * Parabolic springs, 235/75 R17.5 (8 tires) with tire pressure monitoring system * EBS 2S/2M and spring-loaded parking brake * Drawbar with offset plate (+77/-33 mm), without height adjustment, with 50 mm towing eye * Excavator bucket holder made of hardwood on front wall * 1 removable LED warning beacon at the rear ----Trade-in / financing / hire purchase with or without down payment/residual value possible, e.g., over 72 months for as little as €480/month We are MüllerMitteltal trading partners! ----Our opening hours: Monday – Thursday: 08:00 – 17:00 Friday: 08:00 – 15:00 Outside these hours, we are available by appointment We speak German, we speak English, ????? ?? ????? ?????, mowimy po polsku, on parle francais

Stanje: novo, največja dovoljena obremenitev: 8.750 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Oprema: ABS, dvižna zadnja plošča, Inquiry Number: 23185L Financing Price: €26,800 net plus 19% VAT * Now available with attractive hire purchase: * Example: €520 net per month over 60 months, no down payment, no final residual value. * Offer from our financing partner FM LeasingPartner. * We would be pleased to send you a non-binding offer. Financing Price: €26,800 net plus 19% VAT Available immediately New Müller-Mitteltal KA-TA-R 11.9 tandem low-loader three-way tipper trailer with ramps * Tyres: 385/55 R19.5 (4 pcs), BPW axles, parabolic springs, drum brakes * GVW: 11,900 kg, payload: 8,750 kg * Tyre pressure monitoring with display option in the truck via EBS signal * EBS 24 Volt * Side marker lights with indicator control * LED lighting system for 12+24 V * 2 LED reversing lights at the rear (suitable for 12 V and 24 V) * Floor galvanized, 5 m x 2.42 m x 0.5 m, laser-welded side walls, swinging, foldable, and removable * Prepared for subsequent installation of side wall extensions * Support cables for the rear wall * Lockable compartment under the tipper bed for access ramps * Incl. aluminium ramps, 8 t capacity, 3.57 m length, in ramp shaft under the tipping structure * Front wall hot-dip galvanized Nwedpfx Aeykgnbsf Asc * 4 UVV tie-down rings LC 5000 daN front and rear + 8 recessed and foldable lashing rings LC 3000 daN integrated and centred in the tipper floor * Continuously height-adjustable drawbar, hot-dip galvanized, 40 mm towing eye * Net hooks * Bolted, galvanized rear stanchions * One plastic toolbox mounted to the right side of the chassis frame * Access ladder in front of the front wall ---- We are an authorized Müller-Mitteltal dealer Our office hours: Monday - Thursday: 08:00 - 17:00 Friday: 08:00 - 15:00 Outside business hours available by appointment. We speak German, English, Polish, and French. WhatsApp Leasing, financing, and trade-in available ----

Stanje: novo, največja dovoljena obremenitev: 14.660 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 19.0: * Wabco EBS brake system * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 10 t BPW Eco axles * Parabolic springs, 110 mm wide, with tandem equalizer unit * Drawbar with 50 mm flange towing eye and height-adjustable drawbar * Jost landing gear at the front * External folding supports at the rear * Side underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED tail lights * 50 mm softwood floor * Preparation in front of the bulkhead for retrofitting container locks * Bolted smooth sheet metal front wall * Side walls made of trapezoidal profiled steel sheet, foldable with board spring lifter * Steel rear wall, insertable between the ramps (holder for unused panel inside the front wall) * Bolted rear stanchions Nwsdpol Th Hwjfx Af Asc * Outer frame perforated and angled at approx. 45 degrees with 2 t lashing capacity every 480 mm * Possible installation of 3 t recessed lashing rings every 600 mm * In each corner front and rear: 1 x 10 t lashing ring; various holes in the front and end crossmembers for 1.2 t lashing options * Profifix lashing rail centrally along longitudinal axis for lashing up to LC 3,000 daN * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,750 x 620 mm (collapsible to 20 mm) * Rear approach slope approx. 860 mm * Chassis, drawbar, front wall, rear wall, ramps, and folding supports hot-dip galvanized * Side boards painted RAL 9010 pure white * Side wall painting in a RAL color available at extra charge * Axles, springs, air tank, flange towing eye, and landing gear painted in black * New vehicle with full manufacturer warranty * Errors and prior sale excepted * Available approx. from calendar week 21/2026 * Sample images

Stanje: novo, največja dovoljena obremenitev: 13.700 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA 18.0: * 2 in 1 = for roll-off containers and as a low-bed trailer ----Brakes: * EBS electronic braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 10 t axles ----Suspension: Nwsdel Tq Nmjpfx Af Aoc * Air suspension with lift and lower function as well as RTR valve ----Drawbar: * Drawbar, 2,000 mm long with 40 mm towing eye and height adjustment ----Electrics / Lighting: * Tire pressure monitoring system with display option in the truck via EBS signal – no installation on truck side required * LED tail lights 12 / 24 V * 15-pin electrical connector ----General Attachments: * Toolbox made of powder-coated sheet steel, approx. 1,000 x 300 x 600 mm * Storage box for container net made of galvanized sheet, 960 x 300 x 450/400 mm * Contour marking tape, reflective on sides and rear * Side underrun protection * Plastic quarter mudguards with splash guards * Plastic rear collision buffers * Foldable A-board at the rear ----Loading Area: * Main frame with raised outer rails for guiding roll containers * Steel floor plate with roll recesses in the bogie area * Container length from 5,500 – 7,000 mm possible * Pneumatic 4-way clamp locking system and mechanical plug-in stop angles at front of runway, cargo securing certificate according to DIN 30722 - 1 * Weld bead as anti-slip surface in the ramp area * Mechanical rear drop supports ----Load Securing: * 1 pair 10 t UVV lashing rings at the front wall carrier * 3 pairs 10 t UVV lashing rings laterally in outer frame * On each side 4 x 2 t cloverleaf-type lashing eyes * 4 x 8 t lashing brackets recessed in outer frame ----Ramps: * 1 pair aluminium approach ramps (10.6 t/pair) 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment at rear) ----Painting: * Chassis, bogie, locking parts, rear drop supports hot-dip galvanized * However, the drawbar, axles, and air tanks are painted in a shade of black ----Info: * New vehicle without initial registration with full manufacturer's warranty * Errors and prior sale excepted * Sample images ----Delivery Time: * Available approx. from week 23/2026

Stanje: novo, največja dovoljena obremenitev: 13.700 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA 18.0: * 2-in-1: Suitable for both roll-off containers and as a low-bed trailer ----Braking system: * EBS electronic braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10 t axles ----Suspension: * Air suspension with lift and lower mechanism as well as RTR valve ----Drawbar: * Drawbar 2,000 mm long with 40 mm towing eye and height adjustment Nwedpfxsl Tpc Aj Af Asc ----Electrics / Lighting: * Tyre pressure monitoring with display in the truck via EBS signal (no truck-side installation required) * LED rear lights 12 / 24 V * 15-pin power connector ----General attachments: * Toolbox made of powder-coated sheet steel, approx. 1,000 x 300 x 600 mm * Storage box for container net made of galvanized sheet, 960 x 300 x 450/400 mm * Reflective contour tape on sides & rear * Side underrun protection * Plastic quarter mudguards with spray protection * Rear plastic collision bumpers * Foldable 'A' sign at the rear ----Loading platform: * Main frame with raised outer frame for guiding roll-off containers * Steel sheet floor with roll recesses in bogie area * Container length from 5,500 to 7,000 mm possible * Pneumatic 4-point clamp locking and mechanical plug-in stops at the front in the running track, load securing certificate according to DIN 30722-1 * Welded bead as anti-slip coating in the ramp area * Mechanical drop supports at the rear ----Load securing: * 1 pair 10 t UVV lashing rings at the front on the front wall support * 3 pairs of 10 t UVV lashing rings on the sides in the outer frame * On each side, 4 x 2 t cloverleaf style lashing eyes * 4 x 8 t lashing brackets recessed in the outer frame ----Ramps: * 1 pair of aluminium access ramps (10.6 t / pair), 2,800 x 470 mm, suitable for rubber-tyred and tracked vehicles (lockable storage compartment from the rear) ----Painting: * Chassis, bogie, locking parts, rear drop supports hot-dip galvanized * But the drawbar, axles, and air tanks painted black ----Information: * New vehicle without initial registration, full manufacturer's warranty * Subject to errors and prior sale * Sample images ----Delivery time: * Available approx. from CW 23 / 2026

Stanje: novo, največja dovoljena obremenitev: 14.660 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 19.0: * Wabco EBS brake system * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 10 t BPW Eco axles * Parabolic springs (110 mm wide) with tandem equalizing unit * Drawbar with 50 mm flanged tow eye and height-adjustable drawbar * Jost landing gear at the front * Rear external folding supports Nwjdpfol Th Hlsx Af Ajc * Side underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED tail lights * 50 mm softwood flooring * Preparation in front of the bulkhead for retrofitting container locks * Bolted smooth sheet metal bulkhead * Sidewalls made of trapezoidal-profiled steel sheet, foldable with drop-side spring lifting device * Steel rear wall, can be inserted between the ramps (storage bracket inside front bulkhead when not in use) * Bolted rear stanchions * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to fit 3 t folding lashing rings every 600 mm * In each front and rear corner 1 x 10 t lashing ring; various holes in the front and rear crossmember for 1.2 t lashing options * Profifix lashing rail mounted centrally along longitudinal axis, lashing capacity up to LC 3000 daN * One-piece mechanical grid ramps with spring mechanism for single-person operation, approx. 2,750 x 620 mm (can be pushed together to 20 mm) * Rear drive-on slope approx. 860 mm * Chassis, drawbar, bulkhead, rear wall, ramps, and folding supports hot-dip galvanized * Platform sidewalls painted in RAL 9010 pure white * Sidewalls can be painted in any RAL color at extra cost * Axles, springs, air tank, flanged tow eye and landing gear painted black * New vehicle with full manufacturer’s warranty * Errors and prior sale excepted * Available approx. from week 21/2026 * Example images

Stanje: novo, največja dovoljena obremenitev: 14.620 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, Leto izdelave: 2026, * RA-T 18.0 / 018: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Disc brakes * 2 x 10 t BPW wide-track axles * Air suspension (automatic lowering when uncoupling the brake) * Drawbar approx. 2,300 mm long with 40 mm towing eye and height adjustment via draw spring & turnbuckle * Plastic toolbox 450 x 470 mm, right side * Net box on the side, 1,000 x 500 x 500 mm * Enclosed plastic mudguards, front and rear axle * Enclosed side underrun protection, usable as advertising space * Rear underrun protection * Rear plastic impact protection buffer * Rear hazardous goods sign * 15-pin electrical connector * LED tail lights * Roller track length approx. 6,830 mm * Pneumatic 4-point locking clamp system Nodpfxov Nulzj Af Aswc * Mechanically adjustable stop angles (2 positions) at the front left and right on the loading tracks * 265/70 R 19.5 twin tires * 3,220 kg unladen weight * --Gross vehicle weight of up to 20,000 kg technically possible-- * Approx. 1,130 mm loaded ride height * Suitable for container lengths from 5,500 to 7,000 mm * Hot-dip galvanized chassis * Air tanks, axles, turntable, and drawbar * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Immediately available from Egestorf

Stanje: rabljeno, lastna masa: 5.100 kg, največja dovoljena obremenitev: 14.900 kg, skupna masa: 20.000 kg, konfiguracija osi: 2 osi, prva registracija: 02/1997, dolžina tovornega prostora: 8.200 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75R17.5, barva: modra, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Vehicle location: Bovenden. 2 axles, SAF axles, turntable/dolly, leaf suspension, lashing rings, mechanical ramps, rear support, side aluminium underrun protection, twin tires. Body: 2-axle low-loader trailer with mechanical drive-on ramps, 2x SAF axles, drum brakes! Nwsdpfxsv R Hmaj Af Aoc Loading height approx. 900 mm! Ramp length approx. 2650 mm! ACCESSORY DETAILS WITHOUT GUARANTEE—subject to change, prior sale, and errors excepted!

Stanje: rabljeno, lastna masa: 2.910 kg, največja dovoljena obremenitev: 7.590 kg, skupna masa: 10.500 kg, konfiguracija osi: 2 osi, prva registracija: 09/2009, naslednji pregled (TÜV): 04/2025, dolžina tovornega prostora: 4.500 mm, širina tovornega prostora: 2.200 mm, višina nakladalnega prostora: 450 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75R17.5, barva: modra, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Vehicle location: Bovenden, steel body, 2 axles, BPW axles, tandem, leaf suspension, ABS (anti-lock braking system), lashing rings, underrun protection, front support, rear support, swinging tailgates. Nwjdpfx Aov S H Sfjf Aoc Body: Tandem 3-way tipper trailer with ramp recess. Loading ramps available at an extra cost from €900 net! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale and errors!

Stanje: rabljeno, lastna masa: 3.110 kg, največja dovoljena obremenitev: 9.490 kg, skupna masa: 12.600 kg, konfiguracija osi: 2 osi, prva registracija: 05/2016, naslednji pregled (TÜV): 02/2025, dolžina tovornega prostora: 4.550 mm, širina tovornega prostora: 2.380 mm, višina nakladalnega prostora: 600 mm, vzmetenje: jeklo, velikost pnevmatike: 285/70R19.5, barva: modra, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Vehicle location: Bovenden, steel body, 2 axles, turntable trailer, leaf suspension, ABS (anti-lock braking system), lashing eyes, storage box, pendulum flaps. Body: 2-axle 3-way tipper trailer, Gigant axles, drum brakes, hot-dip galvanized frame! Loading height approx. 1290 mm! ACCESSORIES INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale, and errors excepted! Nsdpfx Ajwth Iijf Aswc

Stanje: rabljeno, lastna masa: 2.230 kg, največja dovoljena obremenitev: 3.770 kg, skupna masa: 6.000 kg, konfiguracija osi: 2 osi, prva registracija: 02/1984, dolžina tovornega prostora: 4.000 mm, širina tovornega prostora: 2.000 mm, višina nakladalnega prostora: 500 mm, vzmetenje: jeklo, velikost pnevmatike: 10.5-20, barva: zelen, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Vehicle location: Bovenden, 2 axles, BPW axles, tandem, leaf suspension, ABS (anti-lock braking system), lashing eyes, underrun protection, front support, rear support, swing doors, height-adjustable drawbar. Nwjdpsuxd Rpefx Af Ajc Body: 3-way tipper trailer with towing eye and brake connections (red, yellow). ACCESSORY DETAILS WITHOUT GUARANTEE, subject to change, prior sale, and errors!

Stanje: rabljeno, lastna masa: 3.650 kg, največja dovoljena obremenitev: 10.750 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, prva registracija: 07/2011, naslednji pregled (TÜV): 08/2024, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.430 mm, višina nakladalnega prostora: 900 mm, vzmetenje: zrak, velikost pnevmatike: 285/70R19.5, barva: bela, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Vehicle location: Bovenden, 2 axles, tandem, air suspension, ABS (anti-lock braking system), tailgate, lashing eyes, underrun protection, front support legs, rear support legs, pendulum tailgates, height-adjustable drawbar. Nwedpoth Uavofx Af Aoc Body: Tandem 3-way tipper trailer with aluminium sideboards, 2x Gigant axles, drum brakes! Loading ramps available at an additional cost of €990.00 net! ACCESSORY INFORMATION WITHOUT GUARANTEE. Subject to change, prior sale, and errors excepted!

Stanje: rabljeno, konfiguracija osi: 2 osi, Leto izdelave: 2019, Oprema: ABS, = Other options and equipment = - EBS - Electronic Braking System - Rear air suspension - Front air suspension - Disc brake system = Notes = For inquiries regarding the vehicle, Mr. Seidel will be happy to assist you (by phone). Müller-Mitteltal RA-T 18.0 container chassis Additional rear vehicle headlights, 40mm towing eye, Duomatic, BPW axles, Wabco ABS, disc brakes, spring brake actuators, tire tread depth 1st axle 8-12 mm, 2nd axle 7-11 mm, permissible gross weight: 18,000 kg, unladen weight: 3,290 kg, payload: 14,710 kg Upon request, we can provide you with a leasing or financing offer. Mr. Seidel (phone) will be happy to assist you. For further information, please visit our homepage. ... Errors, changes, and prior sale excepted!!! - = Further information = Unladen weight: 3,290 kg Payload: 14,710 kg Gross vehicle weight: 18,000 kg External dimensions: 0x2550x1250 Please contact Tobias Ebert for more information. Nwsdpfx Ajyfvq Usf Asc

Stanje: rabljeno, lastna masa: 2.700 kg, največja dovoljena obremenitev: 7.300 kg, skupna masa: 10.000 kg, konfiguracija osi: 2 osi, prva registracija: 02/2007, dolžina tovornega prostora: 5.020 mm, širina tovornega prostora: 2.460 mm, višina nakladalnega prostora: 400 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75R17.5, barva: oranžna, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Vehicle location: Bovenden, 2 axles, BPW axles, tandem, leaf suspension, ABS (anti-lock braking system), lashing eyes, mechanical ramps, front support, storage box, height-adjustable drawbar. Body: Tandem low-bed trailer with mechanical loading ramps, 2x BPW axles, drum brakes! Loading height approx. 930 mm! Ramp length approx. 2600 mm! ACCESSORY SPECIFICATIONS WITHOUT GUARANTEE. Subject to change, prior sale, and errors. Nsdpfxowvikqj Af Ajwc