Faymonville Max Trailer 3-Achs-Tele-Semi M. Hydr. Rampen-Nlla. nakup rabljenega (63.526)

Stanje: novo, lastna masa: 9.800 kg, največja dovoljena obremenitev: 39.200 kg, skupna masa: 49.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 9.800 kg, Oprema: ABS, Chassis: - Robust welded steel frame construction with a front frame dip and flat loading platform featuring a rear bevel approx. 500x100 mm - Frame neck 200 mm with chamfered corners at the front - Sloped swan neck end approx. 500 x 100 mm (with anti-slip profile strips on outer frame in the area behind the rear bevel) - 2 king pin positions with replaceable 2” king pin - Outer frame closed to the outside and designed as perforated outer frame Lhsdpfsxgm S Dsx Adgsi - Loading platform with extendable central frame, extendable by around 2,000 mm, lockable in 500 mm increments pneumatically - Frame with 80x80 mm step at and after extension joint - Reinforced frame design / maximum point load when retracted at center of gravity - Without extendible load platform outriggers, but pre-fabricated to allow retrofit (= guide tubes welded in frame) - With excavator trough (no cover), approx. 220 mm deep, 600 mm wide, starting behind 2nd axle to vehicle end - 1 pair of wheel wells between 1st and 2nd axles, covered with steel plates (covers with Körapur coating), approx. 400 mm deep - Rear underrun protection = extended rear plate - Drop-down supports at the rear Ramps: - 2 two-piece loading ramps, special design with mechanical extension - Length approx. 2,850 mm plus 1,850 mm, with hydraulic ramp lifting device (only with electro-hydraulic unit) - Width approx. 800 mm - Wooden surfacing - Including anti-slip strips on ramps - Can be locked in transport position with tie-down straps - Operated by control lever mounted on rear right in frame - Hydraulically laterally adjustable Floor: - 35 mm larch wood floor with aluminium omega profiles Landing legs: - Mechanical 24-ton landing legs with single-sided operation and compensating device Axles, steering and tires: - BPW air suspension axles, each with 10-ton axle load, air bellows diameter 360 mm - S-cam brakes 300/200 mm, asbestos-free brake linings - Automatic slack adjusters - Lifting and lowering system with total lift approx. 200 mm - 2nd driving position via ball valve +50 mm - 1st axle lift axle (wired through EBS), automatic control, with manual override button on the trailer - 3rd axle as friction-steered trailing axle with electric and mechanical lock - 12 steel disc wheels, 10-hole, center offset by center bore - 12 tires, 245/70 R 17.5 143/141J, tubeless - Including tire pressure monitoring system Accessories: - Insertable side and rear stakeboards on the swan neck, approx. 400 mm high - Spare wheel carrier - Side aluminium underrun protection - 4 chocks - 1 plug-in ECE rear warning board - 11 pairs of ZK modules 10t, lateral: - 2x on the swan neck - 2x on loading area before extension - 7x after extension - Extendable warning signs including 3 position lamps each, at the front on landing legs and rear before the rear plate, steplessly extendable up to 4,500 mm loading width - 4 plug-in sockets for warning signs in stake pockets on the loading platform - 6 pairs of stake pockets laterally for 100x50 mm stakes - 2 cross rows stake pockets for 100x50 mm stakes on swan neck, from outer frame to main frame (1x before/1x after king pin positions) - 3 cross rows stake pockets for 100x50 mm stakes on loading area from outer frame to main frame (1x before the extension, 1x after extension, 1x after the 3rd axle) - 2 pairs of steel plates in the loading platform for container locks to accommodate 1x 20ft container - Rubber apron mounted on underrun protection

Stanje: novo, lastna masa: 12.300 kg, največja dovoljena obremenitev: 37.200 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear chamfer of approx. 750 mm x 10° - 30 mm thick hardwood flooring Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system Gooseneck: - Gooseneck with rear chamfer of approx. 750 mm x 10° - 3 pairs of lashing rings - 30 mm thick hardwood flooring Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system - Maximum load capacity per pair: 30,000 kg Lodotvfkfopfx Adgshi Loading area: - Loading area with rear chamfer of approx. 1,000 mm x 8° - Hardwood flooring approx. 48 mm thick, chequer plate flooring above the axles Axles and tires: - BPW axles and suspension, two rigid axles, one self-steering trailing axle - Air suspension with lift and lower valve - The trailing steering axle with electro-magnetic reversing lock, activated by reverse gear or manually - Tyres 235/75 R17.5 3PMSF Included accessories: - 1 spare wheel with holder - TPMS tyre pressure monitoring system according to ECE R 141 - 2" kingpin - One galvanized steel front wall - Yellow-red air couplings on the galvanized front connection rail - 4 chocks with holder on the front wall - Rear mounting area on the gooseneck for ALU approach ramps - 3 heights of aluminium planks - Galvanized folding supports under the loading area chamfer - Height-adjustable tarpaulin body (3,960 mm) - Galvanized front wall with tensioning mechanism for sliding curtain - Height adjustable by approx. 400 mm - "EDSCHA" brand roof, forward-sliding on ALU roof beam profiles, bolted to front and rear walls - 3 pairs of movable stakes in the loading platform - The superstructure is hydraulically extendable at the rear to the left and right by approx. 750 mm - Sliding roof with high-swivelling portal beam - Sliding curtain with 700 mm length surplus, with tensioning straps spaced approx. 600 mm apart - Height to top of the body: approx. 3,960 mm - Driving with open sliding roof is not permitted and will damage the curtain - Cover plates to bridge the gap between ramps and loading area - Rear electro-hydraulic unit under the loading platform - On gooseneck and ramps, each side with one holder for warning signs including socket - Ramp control valves located on right-hand side of trailer - 6 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading area - Lift axle on the front axle - Grating surface in the chamfer of the loading area C40/4 (point load 3.4 t on an area of 20 x 20 cm) - One INOX toolbox 565 x 290 x 810 mm, mounted on the right side in the direction of travel between the axles - Painted sand layer as anti-slip protection on the chequer plates on the gooseneck and loading area - BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable cover for the pump - Four extendable warning signs (approx. 400 mm each) approx. 423 x 423 mm with position light - Axle load gauge including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Entire steel structure shot-blasted, afterwards defined visible surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) hot-refined

Stanje: novo, lastna masa: 17.500 kg, največja dovoljena obremenitev: 43.500 kg, skupna masa: 61.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.750 mm, višina nakladalnega prostora: 400 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - For tractor units: 6x4 or 8x4 Lowbed: - Lowbed with external beams, extendable version, "SUPER LOW" design, approx. 7,550 mm long - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking device - Service lines are protected within the extendable beams and automatically adjust to the lowbed length Rear Undercarriage: - Rear chassis with closed outer frame, checker plate cover, and continuous prism-shaped excavator trough approx. 1,450/900 x 505 mm, open at the rear - 2 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame Axles and Tires: - "PENDULUM AXLE", all axles hydro-mechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 / 3PMSF Included Accessories: - Prepared for bolt-on container positioning for 1x 20ft or 1x 40ft container on the outer beams - 2" kingpin - Galvanized steel front wall approx. 400 mm high - One spare wheel with holder - At the galvanized front adapter bar yellow-red air couplings - 4 wheel chocks - Remote rear steering from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Hydraulic line connections from gooseneck to lowbed with multi-coupling instead of screw coupling - Electro-hydraulic power pack - White reflective tape to EU specifications on sides, extension, and rear red - 2 wooden blocks 500x250x200 mm - European reflective plates (red-yellow) on the trailer rear - At the gooseneck and rear wall left and right each a bracket for warning boards including socket - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 - Load gauge for determination of axle loads including load diagram - On the gooseneck, plug-in ALU side and rear boards approx. 2,000 x 400 mm - The rear galvanized insert posts are removable (body length approx. 2,120 mm) - Separate air connection for air gun on the gooseneck - Duomatic air coupling from gooseneck to lowbed - Rear upper section of gooseneck closed with removable cover - 1 pair of steel ramps to bridge the lowbed's pick-up hooks - Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm - Wireless remote control for rear steering in addition to cable remote, with signal lights at receiver for single-track monitoring - 6 pairs of threaded blocks between lashing rings under the top chord on the outer beams for mounting screwable RUD rings VLBG-4 - 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading bed - Foldable extensions, approx. 230 mm per side - Loading area features a painted sand layer for anti-slip protection - Dipper stick trough of rear chassis closed at front and rear with plug-in plates Lhedpfsh Hm Thex Adgoi - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - alu 15%)

Stanje: novo, največja dovoljena obremenitev: 38.100 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.100 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5 3PMSF, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer of approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading platform: 5 pairs of fold-out lashing rings 3 pairs of fold-out lashing rings 1 pair of horizontal lashing rings at the front of the loading area Cut-outs in the outer frame of the loading surface for hooking in tension belts Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Landing legs: JOST landing legs with 2-speed gears for a 24 t lifting capacity Axles and tyres: BPW axles, two axles are fixed, two axles are self-steering, air-suspended, with drum brakes, with lift/lower function The self-steering axles come with an electro-magnetic reverse lock, which is activated via reverse gear or manually Axle toolkit Tyres: 205/65 R17.5 3PMSF Brake system: WABCO brake system according to EU regulations with EBS-E Steel construction: Steel structure made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Electrical equipment: Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK lighting ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component zinc dust primer High-quality single-colour 2-component top coat in MB 7350 Novagrau No metallic paint possible Rear section metallized and painted in RAL 9010 Accessories included: 1 spare wheel 205/65 R 17.5 TPMS tyre pressure monitoring system acc. to ECE R 141 At the galvanized front connection strip yellow-red air couplings 4 wheel chocks with holder on front wall Bracket at rear of gooseneck for ALU access ramps Galvanized folding supports under the chamfer of the loading surface Mount for a revolving beacon at the rear of the trailer Height-adjustable curtain structure Galvanized front wall with a tension mechanism for the sliding curtains Lodpfxetphtms Adgshi Height-adjustable by approx. 400 mm "EDSCHA" brand roof, sliding forward on ALU roof beam profiles, bolted to the front and rear wall In the loading surface, 3 pairs of sliding stakes Superstructure at rear hydraulically extendable to left and right by approx. 750 mm Sliding roof with upward swinging portal carrier Sliding tarp with 700 mm reserve length, with tension straps at intervals of approx. 600 mm Height to top edge of superstructure approx. 3,960 mm Journeys with the sliding roof open are not permitted and will damage the tarp Mounting rail for ALU access ramps at the rear of the vehicle At the gooseneck and at the rear panel left and right, each with a mount for warning signs incl. socket A mud flap at the rear of the trailer European reflector plates at the rear of the trailer 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading area Lifting axle on the front axle controlled by TEBS E depending on current axle load and load status Rear structure with closed ALU double-wing doors A sanded, anti-slip paint layer on the checker plates on the gooseneck and on the loading surface BEKAMAX centralized lubrication system with standard grease NLGI-2 and a removable guard around the pump Speed stickers 80 km/h on rear and both sides Load manometer for axle load determination including load chart

Stanje: novo, lastna masa: 34.500 kg, največja dovoljena obremenitev: 106.700 kg, skupna masa: 141.200 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.150 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 580 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, obratovalna teža: 34.500 kg, Oprema: ABS, Gooseneck: - Gooseneck hydraulically lift/lowerable as well as detachable - Length approx. 3,650 mm - Extensive lashing positions - For tractor units: 6 x 4 or 8 x 4 3-Axle Compact Front Bogie: - Hook mounts at front and rear - Chassis length x chassis width approx. 3,560 mm x 2,850 mm - Extensive lashing positions Excavator Deck “BB-A”: - Telescopic excavator deck “BB-A” with drive-over deck hooks at the front and bolted lug coupling at the rear - Length x base width approx. 7,150 mm x 2,850 mm - Beam height x beam width approx. 430 mm x 1,350 mm - Loading height 580 mm with 150 mm ground clearance - 5 pairs of hanging lashing rings (LC 10,600 daN) - 4 pairs of threaded blocks M30 on inner beam for mounting screw-on rings 5-Axle Rear Bogie: - Mechanical bolt-on lug coupling for fitting a lowbed front, rear end traverse - Chassis length x chassis width approx. 6,840 mm x 2,850 mm - Extensive lashing positions Pendulum Axle and Tyres (front and rear bogie): - “PENDEL-AXLE”, all axles hydromechanically forced-steered Lodpfewhywfsx Adgshi - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-plugs for securing in lifted position - Final paint of axles with 2 coats of 2K paint, single-colour in MB 7350 Novagrau - Technical axle load: 14,640 kg (62 km/h) - Hydraulic axle compensation - Axle tools - Tyres 285/70 R19.5 Steering Override: - Remote steering from the front and rear via cable remote control with push buttons, including axle tracking control - Socket for steering control operation on the gooseneck - Cable remote control with push buttons including axle tracking control Included accessories: - Yellow-red air couplings on galvanised front connection rail - Steel headboard approx. 400 mm high - 4 wheel chocks with holders - 2 spare wheels 285/70 R19.5 - 3.5" kingpin - Gantry with winch for spare wheel at the front side of the gooseneck - Truck hydraulic connection with flow control valve (40 l/min), including gantry for suspension of supply lines, tractor unit tank must be at least 80 litres with couplings - White reflective tape according to EU regulations on sides and extension, red at rear - Plug-in ALU side panels and rear wall on gooseneck, approx. 400 mm high, anodised - Operating lever on gooseneck protected by folding cover - Separate air connection with air pistol on gooseneck - Central lubrication system BEKAMAX with standard grease NLGI-2: 1x on the gooseneck, 1x on 3-axle bogie, 1x on 5-axle bogie - Variomax tool kit - Multi-coupling hydraulic connections in the lowbed hook area - Front bogie with separate air connection for air screwdriver - Threaded inserts (ø 40 mm) every approx. 500 mm on outside of upper flange of excavator deck for screw rings - Folding extensions with steel mats, width adjustable from approx. 2,850 mm to approx. 3,250 mm - Steel mats with rubber covering approx. 12 mm thick - Two INOX toolboxes 855 x 340 x 390 mm - Radio remote control for steering override in addition to cable remote - Painted sand layer as anti-slip measure - 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery

Stanje: novo, lastna masa: 14.350 kg, največja dovoljena obremenitev: 53.450 kg, skupna masa: 67.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, dvižna zadnja plošča, Gooseneck: - Gooseneck in SNT design for optimization of loading bed length, length approx. 3,700 mm - Gooseneck rear with chamfer approx. 1,000 mm x 10° - For tractor units: 6x2, 6x4, 8x4 short Loading bed: - Extendable loading bed, length approx. 8,800 mm, rear chamfer approx. 500 mm x 10° - A recess in the loading bed and the chamfered section for receiving the excavator dipper stick, approx. 3,850 x 750 x 210/290 mm Two-part steel ramps: - One pair of two-part steel ramps, length approx. 4,350 mm, width approx. 900 mm - Ramps with rubber covering - Ramps hydraulically adjustable individually approx. 235 mm outwards and approx. 215 mm inwards - 'Super Grip' 25 mm rubber flooring and approx. 5 mm steel plate as additional reinforcement on the rear chamfer of the loading bed - Square climbing bars 20 x 30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: - BPW axles and suspension, 1st axle steering, all other axles hydromechanically forced-steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Tires 235/75 R 17.5 - TPMS tire monitoring system according to ECE R141 - TPMS tire sensors fitted on all wheels, including spares Surface treatment: - Complete steel structure automatically blasted with shot blasting system after welding - Second blasting with corundum for optimum coating adhesion - HRM metallization of entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for best corrosion protection - Final painting with 2 layers of 2K top coat, single colour in MB 7350 Novagrau Accessories included: - Plug-in steel front wall, approx. 400 mm high - 3kW electro-hydraulic power unit for controlling hydraulic functions, with the exception of hydraulic winches - 1 spare wheel - Outer carrier on the gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings in the rear area of the gooseneck - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized - On the gooseneck, 1 plug-in ALU rear board, approx. 400 mm high, anodized - On top of the gooseneck, approx. 40 mm thick hardwood flooring, above kingpin area with checker plate cover - 2" kingpin - Round NATO socket on front connection strip - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front cross member - 8 pairs of recessed, fold-out lashing rings in the outer frame of the loading bed - Extendable (galvanized) widenings by approx. 230 mm per side - Wheel recesses with square climbing bars, 15 x 15 mm, in front of the axles fully open up to gooseneck cross beam, approx. 700 x 410 mm - Wheel recesses with square climbing bars, 15 x 15 mm, between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - ALU covers for wheel recesses, which can also be used as bridging elements for the extension or as widening boards - 1 pair mechanical rear supports - Radio and cable remote control - Lift axle on front axle - Square climbing bars 20 x 30 mm, approx. every 200 mm Lhedpfx Ajya E A Nedgsi - Central lubrication system with 1 pump - Wabco Smart Board system - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, lastna masa: 6.350 kg, največja dovoljena obremenitev: 38.650 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22,5, Oprema: ABS, Loading Platform: - 2 pairs of folding external lashing rings (LC 5,000 daN) - 24 pairs of cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) Landing Legs: - JOST mechanical landing legs with 2-speed gearbox, 24 t lifting capacity (50 t test load) Axles and Tyres: - BPW axles, air suspended, with disc brakes (430 mm), lift/lower function - Tyres: 385/65 R 22.5 Braking System: - WABCO braking system compliant with EU regulations featuring EBS-E (2S2M) Paintwork: - Premium and durable corrosion protection of the standard grit-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) top coat in single-tone MB 7350 Novagrau - Rear section metallized and painted in RAL 9010 (pure white) - Metallic paintwork not possible Steel Construction: - Steel construction made from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical System: - Electrical system in accordance with EU regulations - Lighting: 24 volt - ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connection bar with 24N, 24S, and 15-pin sockets - Connection standards: - 24N ISO-1185 Lhjdpfx Aeiu Etksdgji - 24S ISO-3731 - 15-pin ISO-12098 Accessories included: - Yellow-red air couplings at the galvanized front connection bar - 4 wheel chocks with holders - 2" king pin - Galvanized steel front wall approx. 1,600 mm high, EN12642-XL - White reflector tape according to EU regulations, lateral and rear red - European reflective panels (red-yellow) at the rear of the trailer - Loading platform with approx. 30 mm thick hardwood flooring, framed in omega profiles - 10 pairs of stanchion sockets for 100 x 50 mm plug-in stakes in the outer frame - 3 pairs of transverse stanchion rack strips, fitted in the loading platform, for 100 x 50 mm plug-in stakes - Bracket for 1,000 mm plug-in stakes, rear in the central beam - 1 spare wheel carrier under the loading platform on the right hand side - 1 mudflap at the rear of the trailer - Manual and description on USB stick - Bracket for beacon at the rear of the trailer - Holders for warning signs including socket at the gooseneck and left/right rear panel - 6 pairs of WADER container locks on the loading platform for 1x 20ft, 2x 20ft, or 1x 40ft container, flush with rear - 80 km/h speed stickers at the rear and both sides - Four warning signs, extendable by approx. 400 mm, approx. 423 x 423 mm, with LED position light - Load gauge for axle load determination including load diagram - HRM (High Resistance Metallisation) of the outer frame - Complete steel structure is grit blasted, then defined visible surfaces are metallized with ZINACOR 850 (zinc 85% - aluminium 15%) by hot coating

Stanje: rabljeno, lastna masa: 10.100 kg, največja dovoljena obremenitev: 38.900 kg, skupna masa: 49.000 kg, konfiguracija osi: 3 osi, prva registracija: 09/2025, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.550 mm, velikost pnevmatike: 245/70 R 17,5, barva: siv, Leto izdelave: 2025, Oprema: ABS, Za vsako rabljeno polpriklopno vozilo prejmete aktualno in popolno poročilo o pregledu ter delovanju. Podvozje: -Stabilna varjena jeklena konstrukcija okvirja z dvignjenim sprednjim delom in ravno nakladalno površino z zadnjim poševnim zaključkom približno 500x100 mm -Vrat okvirja višine 200 mm z zaobljenimi vogali -Poševni zaključek "grbine" (Schwanenhals) približno 500 x 100 mm (dvižni rebrasti profili na zunanjem okvirju za zadnjim poševnim delom) -2 mesti za king pin z zamenljivim 2'' king pinom -Zunanji okvir zaprt navzven z luknjami za privezovanje z napenjalnimi trakovi (pritrditev s verigami ni možna) -Ojačana izvedba okvirja / točkovna obremenitev v težišču -Priprava za izvlečne razširitve v nakladalni površini -Z bagrskim izrezom (brez pokrova), globina približno 220 mm, širina približno 600 mm, začne se za 2. osjo in poteka do zadka vozila -1 par blatniških izrezov pred osjo z jeklenimi pokrovi (pokrovi prevlečeni s premazi Körapur), globina približno 400 mm, ter še 1 par med 1. in 2. osjo z jeklenimi pokrovi -Zaščita pred podvozjem = podaljšana končna plošča -Podporne noge zadaj Rampi: -Dvodelne nakladalne rampe posebne izvedbe z mehanskim podaljšanjem -Dolžina približno 2.850 mm plus 1.850 mm, z hidravličnim dvigalom (samo v kombinaciji z elektrohidravličnim agregatom) -Širina približno 800 mm -Lesena površina -Vključene dvižne rebraste plošče na nakladalnih rampah -V transportnem položaju z možnostjo pritrditve z napenjalnimi trakovi -Upravljanje prek ročice, nameščene zadaj desno v smeri vožnje -Stransko hidravlično pomične Tla: -35 mm tla iz macesnovega lesa z aluminijastimi Omega profili Podporne dvigala: -Mehanske podporne dvigala 24 t s stranskim upravljanjem in izravnavo potiska Osovine, krmiljenje, pnevmatike: -BPW zračno vzmetene osi, vsaka 10 t dovoljene nosilnosti, premer zračnih mehov 360 mm -Zavore z Z-kamnom 300/200 mm, obloge brez azbesta -Avtomatski napenjalec zavornih palic -Dvigovanje in spuščanje s skupnim hodom približno 200 mm -2. položaj za vožnjo z dodatkom krogličnega ventila +50 mm Lhsdszdzrtjpfx Adgei -1. os dvižna os (preko EBS sistema), avtomatsko potrjevanje s mehanskim ročnim upravljanjem na priklopniku -3. os z obračalno osjo z električnim in mehanskim zaklepom -12 jeklenih platišč, 10 lukenj, z natančno namestitvijo na sredino -12 pnevmatik 245/70 R 17,5 143/141J, brez zračnic -Vključno s sistemom za nadzor tlaka v pnevmatikah Dodatna oprema: -Na grbi (Schwanenhals) snemljive bočne in zadnje stranice višine približno 400 mm -Nosilec za rezervno kolo -Bočna aluminijasta zaščita pred udarci -4 podložni zagozdi s pritrditvijo -Podaljšani nosilec za registrsko tablico na končni plošči -1 ECE tablica zadaj, snemljiva -11 parov ZK modulov 10 t ob strani: -2x na grbi -9x na nakladalni površini -Izvlečne opozorilne table, vključno s po 3 pozicijskimi lučmi, spredaj na podpornikih za prikolico in zadaj pred končno ploščo, brezstopenjsko izvlečne do nakladalne širine 4.500 mm -4 nosilci za opozorilne table, vstavljivi v žepe na nakladalni površini -6 parov bočnih žepov za stebre 100x50 mm -2 prečni žepi za stebre 100x50 mm na grbi (zunanjega okvirja do glavnega okvirja; 1x pred in 1x za položaj king pina) -3 prečni žepi za stebre 100x50 mm na nakladalni površini (1x spredaj, 1x pred 1. osjo, 1x za 3. osjo) -2 para jeklenih plošč na nakladalni površini za priklop kontejnerjev 1x 20ft -Gumijasta zavesa montirana na zaščito pred podvozjem

Stanje: rabljeno, lastna masa: 10.100 kg, največja dovoljena obremenitev: 38.900 kg, skupna masa: 49.000 kg, konfiguracija osi: 3 osi, prva registracija: 07/2025, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.550 mm, velikost pnevmatike: 245/70 R 17,5, barva: siv, Leto izdelave: 2025, For every used semi-trailer, you receive a current and complete inspection and functional report. Chassis: - Robust steel frame welded construction with front cranked frame and flat loading area, inclined at the rear approx. 500x100 mm - Frame neck 200 mm with chamfered corners - Sloped end of gooseneck approx. 500 x 100 mm (traction ribs on outer frame in the rear sloped area) - 2 kingpin settings with replaceable 2" kingpin - Outer frame closed outward as perforated external frame for lashing with tension straps (chains not possible) - Reinforced frame design / point load at the center of gravity - Provisions for extendable load floor widenings - With excavator trough (without cover), depth approx. 220 mm, width approx. 600 mm, starting after 2nd axle to end of vehicle - 1 pair of wheel recesses in front of the axle with steel covers - (Covers with Körapur coating), depth approx. 400 mm, and 1 pair of wheel recesses between 1st and 2nd axle steel covers - Underrun protection = extended end plate - Drop-down supports at rear Ramps: - 2-piece special-design loading ramps, mechanically extendable - Length approx. 2,850 mm plus 1,850 mm, with hydraulic ramp lift (only in conjunction with electrohydraulic unit) - Width approx. 800 mm - Wood surface - Incl. traction ribs on loading ramps - Can be secured in driving position with tension straps - Actuated via control lever mounted to the right at rear in direction of travel - Laterally hydraulically adjustable Floor: - 35 mm larch wooden floor with aluminum omega profiles Lhedpjzabnbjfx Adgji Landing Gears: - Mechanical 24t landing gears with one-side operation and push rod compensation Axles, Steering and Tyres: - BPW air suspension axles, each 10t axle load, air bag diameter 360 mm - S-cam brakes 300/200 mm, asbestos-free brake linings - Automatic slack adjuster - Lift and lower mechanism with total lift approx. 200 mm - 2nd driving position via ball valve +50mm - 1st axle lift axle (wired via EBS), fully automatic control with mechanical emergency operation via button on the trailer - 3rd axle self-steering trailing axle with electric and mechanical lock - 12 steel disc wheels, 10-hole, with centered offset - 12 tires 245/70 R 17.5 143/141J, tubeless - Including tire pressure monitoring Accessories: - Plug-in side and rear walls approx. 400 mm high on gooseneck - Spare wheel holder - Lateral aluminum side underrun protection - 4 wheel chocks with holders - Long license plate holder in end plate - 1 ECE-board insertable at the rear - 11 pairs of ZK modules 10t laterally: - 2x on the gooseneck - 9x on the loading area - Extendable warning signs incl. 3 position lights each, at front on landing gears and rear before end plate, infinitely extendable up to loading width of 4,500 mm - 4 fittings for warning signs, plug-in to pockets on loading area - 6 pairs of stake pockets at sides for stakes 100x50 mm - 2 rows of crosswise stake pockets for stakes 100x50 mm on gooseneck from outer frame inwards up to main frame (1x before and 1x after kingpin positions) - 3 rows of crosswise stake pockets for stakes 100x50 mm on load area from outer frame inwards up to main frame (1x front, 1x before 1st axle, 1x after 3rd axle) - 2 pairs of steel plates in loading area for container locks to accommodate one 20ft container - Rubber skirt mounted on underrun protection

Stanje: novo, lastna masa: 10.100 kg, največja dovoljena obremenitev: 38.900 kg, skupna masa: 49.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.550 mm, velikost pnevmatike: 245/70 R 17,5, obratovalna teža: 10.100 kg, Oprema: ABS, Chassis: - Sturdy welded steel frame construction with front frame cranking and flat loading platform, rear ramped section approx. 500x100 mm - Gooseneck 200 mm with beveled corners - Sloped gooseneck end approx. 500x100 mm (traction ribs on outer frame behind rear inclination) - 2 kingpin positions with replaceable 2" kingpin - Outer frame closed on the outside as perforated frame for lashing with tension belts (chains not permitted) - Reinforced frame design / point load at the center of gravity - Prepared for extendable load platform widenings - With excavator trough (without cover), depth approx. 220 mm, width approx. 600 mm, starting after 2nd axle to end of vehicle - 1 pair wheel recesses in front of axle with steel covers (covers with Körapur coating), depth approx. 400 mm, and 1 pair between 1st and 2nd axle, steel covers - Underrun protection = extended end plate - Drop-down supports at rear Ramps: - 2-piece drive-up ramps, custom design, with mechanical extension - Length approx. 2,850 mm plus 1,850 mm, with hydraulic ramp lifting mechanism (only in connection with electrohydraulic unit) - Width approx. 800 mm - Wood topping - Incl. traction ribs on ramps - Can be secured for travel with tension belts - Operated by manual lever mounted rear right in direction of travel - Hydraulically laterally shiftable Floor: - 35 mm larch wood floor with aluminum omega profiles Landing Gears: - Mechanical 24 t landing gears, operated from one side with load equalization Axles, Steering, and Tires: - BPW air suspension axles, each rated at 10 t axle load, airbag diameter 360 mm - S-cam brake 300/200 mm, asbestos-free brake linings - Automatic slack adjuster - Lift and lower device, total stroke approx. 200 mm - 2nd drive position via ball valve +50 mm - 1st axle as lift axle (wired via EBS), operation fully automatic with mechanical emergency actuation via button on trailer - 3rd axle as friction steered trailing axle with electric and mechanical lock - 12 steel disc wheels, 10-hole, center-fitted offset - 12 tires 245/70 R 17.5 143/141J, tubeless - Including tire pressure monitoring Accessories: - Plug-in side walls and rear wall on gooseneck approx. 400 mm high - Spare wheel holder - Lateral aluminum underrun protection - 4 wheel chocks - Long license plate holder in end plate Ledpfx Aowviwkjdgohi - 1 detachable ECE sign at rear - 11 pairs ZK modules 10t on the sides: - 2x on the gooseneck - 9x on the load platform - Steel mudguards with clear pass - Extendable warning panels incl. 3 position lamps each, front at landing gears and rear before end plate, infinitely extendable up to loading width 4,500 mm - 4 plug-in holders for warning panels in stake pockets on loading surface - 6 pairs of lateral stake pockets for 100x50 mm stakes - 2 rows of crosswise stake pockets for 100x50 mm stakes on the gooseneck from outer frame towards main frame (1x before and 1x after kingpin positions) - 3 rows of crosswise stake pockets for 100x50 mm stakes on loading platform from outer frame towards main frame (1x in front area, 1x before 1st axle, 1x after 3rd axle) - 2 pairs of steel plates in load platform for container locks to receive 1x 20ft container - Rubber apron mounted on underrun protection - Steel shot blasting, chassis hot-dip galvanized and primed - Chassis/wheel hubs/outer frame painted in DB 7350 Nova grey

Stanje: rabljeno, lastna masa: 17.430 kg, največja dovoljena obremenitev: 67.570 kg, skupna masa: 85.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2026, dolžina tovornega prostora: 9.400 mm, širina tovornega prostora: 2.740 mm, višina nakladalnega prostora: 850 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Leto izdelave: 2026, Oprema: ABS, Labod: -Labod v obliki "labodjega vratu" (Schwanenhals) v zasnovi SNT za optimizacijo dolžine tovornega prostora, dolžina približno 3.700 mm, zadaj s poševnostjo približno 1.000 mm x 10° Tovorni prostor: -Tovorni prostor v izvlečni izvedbi z gumirano površino "Super-Grip" nad osmi, dolžina približno 9.400 mm s poševnostjo na zadnji strani približno 500 mm x 10° -Vdolbina v tovornem prostoru in v poševnosti, v katero se pomika ročica bagrovega žlica, velikost približno 3950 x 780 x 370/450 mm -Pnevmatska zaklepna naprava s koničnim zaklepnim vijakom in ojačanimi položaji za zaklepanje Osi in pnevmatike: -Polososi tipa TWINAXLE II, posamično vzmetenje koles, 1. os vodena s krmilno povezavo, vse ostale osi hidro-mehansko prisilno usmerjene -1. os z elektro-magnetno zaporo za vožnjo v vzvratno smer, aktivira se s prestavo za vzvratno vožnjo in ročno -Tehnična nosilnost osi: 12.000 kg -Hidravlično izenačevanje osi -Hidravlični cilindri z zapornimi ventili -Pnevmatike: 245/70 R 17.5 3PMSF, dvojne pnevmatike Dvodelne jeklene rampe: -Par dvodelnih jeklenih ramp z dolžino približno 4.650 mm in širino približno 900 mm -Z gumirano površino "Super-Grip" -Hidravlično dvižne konice ramp -Rampe se posamično hidravlično premikajo za približno 235 mm navzven in približno 215 mm navznoter Popolna metalizacija: -Popolna HRM-metalizacija (metalizacija z visoko odpornostjo) -Celotna jeklena konstrukcija, obdelana s peskanjem, nato pa s toplotno obdelavo s premazom ZINACOR 850 (cink 85 % - aluminij 15 %) Dodatna oprema: -Čelna stena iz jekla, vstavljiva, približno 400 mm visoka, priključna letev za napajalne kable za nadgradnjo, nameščena na višini zunanjega okvirnega profila -1 kos orodjarjeve škatle iz nerjavečega jekla (INOX), enodelna, približno 2.480 x 340 x 390 mm, v ravni izvedbi, z 2 stranskima vrati na zunanji strani in 1 pokrovom na vrhu, za čelno steno na labodu -Okrogla vtičnica NATO na priključni letev na sprednji strani (Maeler & Kaege VG 96 917) -Spiralni kabel za napajanje elektro-hidravlične enote in/ali električnega vitla (35 mm², 3,5 m dolg) med priklopnikom in nadgradnjo, z vtičem -Elektro-hidravlična enota 3 kW za nadzor hidravličnih operacij, razen hidravličnih vitlov -Dodatna možnost uporabe priključkov za hidravlični pogon motornega vozila, vključno z ventilom za zmanjšanje tlaka. Priključni elementi so v dobavi kupca -Parkirni položaj na labodu za opozorilne table, kadar se ne uporabljajo -1 rezervno kolo -Zunanji nosilec laboda z luknjami za pritrditev vijakov za pritrditev zank -Prva luknja je približno 200 mm od sprednje strani, nato pa približno vsakih 400 mm -2 para vijačnih zank, vključno z njimi -1 par horizontalnih zank na zadnjem delu laboda -Na labodu 1 par vstavnih aluminijastih stranskih ograj, približno 400 mm visoke, eloksirane -Na labodu 1 vstavna aluminijasta zadnja ograja, približno 400 mm visoka, eloksirana -Nad labodom ploščata obloga iz trdega lesa debeline približno 40 mm, nad peto ploščata obloga iz valovite pločevine -3,5" peta -Vodilna plošča laboda za ploščo sedla, širina približno 500 mm -Mehanske podpore sedla Lhjdezmtu Eopfx Adgoi -Zaklepanje tovornega prostora s konično varjenimi profili za zaklepanje na vsakih 250 mm -Vključno s prednapenjalno ploščo -1 premikajoča se vmesna plošča, širina približno 300 mm, za izvlečno cev z velikim prečnim prerezom, z valovito pločevino spredaj in zadaj, z dolgimi luknjami za pritrditev in premikanje premostitvenih elementov -1 par hidravličnih zadnjih opornih nog -Centralni sistem za m

Stanje: rabljeno, lastna masa: 14.995 kg, največja dovoljena obremenitev: 50.805 kg, skupna masa: 65.800 kg, konfiguracija osi: 3 osi, prva registracija: 10/2023, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, barva: siv, Leto izdelave: 2023, obratovalna teža: 14.995 kg, Oprema: ABS, For every used semi-trailer, you will receive a current and comprehensive inspection and functionality report. Gooseneck: - Gooseneck with rear bevel, approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading platform: - Extendable loading platform with rear bevel, approx. 500 mm x 8° - 6 pairs of fold-out lashing rings to the outside (LC 5,000 daN) - 4 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) - 1 intermediate section, 250 mm - Cut-outs in the outer frame of the loading area for inserting tensioning straps (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, chequer plate over the axles Axles and tyres: - BPW axles with hydro-mechanical forced steering - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - Axle tools - Tyres 235/75 R17.5 Braking system: - Braking system according to EU regulations with EBS-E (4S3M) Accessories included: - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings mounted on the galvanized connection strip at the front - 4 chocks with holders on the front wall - One spare wheel with holder in front of the front wall - Electro-hydraulic power unit - Remote steering from front and rear via cable remote control with push buttons, including single-track control of the axles - Mounting for ALU ramps at the rear of the gooseneck - Hot-dip galvanized, extendable side extensions, approx. 230 mm per side - European reflector boards (red-yellow) at the rear of the trailer - White reflective tape as per EU standards on the sides, on the extension, and red at the rear - Bracket for warning signs on left/right of gooseneck and rear panel, incl. socket - Galvanized folding supports under the loading platform’s rear bevel - Holder for a beacon at the rear of the trailer - Central lubrication system with 2 BEKAMAX (Pico) pumps, NLGI-2 standard grease and removable cover for the pump - Mud flap at the rear of the trailer - Manual and documentation - On the gooseneck: insertable ALU side boards and rear wall, approx. 2,440 x 400 mm - Removable galvanized stanchions at the rear (body length approx. 2,560 mm) - 4 pairs of WADER container locks recessed in the loading platform for 1x 20ft, 2x 20ft, 1x 40ft, or 1x 45ft container - 8 pairs of pockets for removable stanchions, 100 x 50 mm, in the outer frame of the loading platform Lhedpfx Asv Hr Axedgoi - Adjustable hook rails for ALU ramps at the rear of the vehicle - Lift axle on the front axle, controlled by TEBS E depending on current axle load and loading condition - Four warning panels, extendable approx. 400 mm, approx. 423 x 423 mm, each with position lamp - Mounting on warning panels for beacon - Radio remote control for remote steering in addition to cable remote control, with indicator lights on the receiver for single-track control - Painted-in sand layer on chequer plates, above the king pin and on the loading area for anti-slip protection - 80 km/h speed limit decal at the rear - Load pressure gauge for axle load determination, including load chart

Stanje: novo, lastna masa: 10.300 kg, največja dovoljena obremenitev: 39.200 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Platform: - Loading platform after the gooseneck, hydraulically liftable and lowerable, length approx. 2,800 mm, with rear chamfer approx. 1,000 mm x 8° - Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, over the axles with chequer plate covering Two-part Steel Ramps: Lhsdpou Hp Hrofx Adgji - One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp parts, hydraulic lifting system, and hydraulically adjustable - Maximum load per pair: 40,000 kg Axles, Suspension and Tires: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated by reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tires 235/75 R 17.5 3PMSF - TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories Included: - One spare wheel with holder in front of the bulkhead - 2" kingpin - One galvanized steel front wall approx. 400 mm high - Yellow-red air couplings at the galvanized connection strip in front - 4 wheel chocks - Galvanized folding supports under the platform's rear chamfer - A holder for a rotating beacon at the rear of the trailer - Cover plates to bridge the gap between ramps and platform - White reflective tape as per EU regulations along the sides of the trailer and red at the rear - Electro-hydraulic unit at the rear, under the platform - At the gooseneck and at the ramps left and right, each with a holder for warning signs, including socket - Control valves for the ramps positioned on the right side of the trailer - European reflective plates (red-yellow) at the rear of the trailer - Manual and description on USB stick - Removable ALU side walls and rear wall on the gooseneck approx. 2,440 x 400 mm - The rear, galvanized side stakes are removable (body length approx. 2,560 mm) - An electric cable winch with radio remote control, approx. 5,400 kg lifting force, including 9.5 mm steel cable, 24 m long, with guide roller - Bolted 5 t ring for cable deflection of the winch on the gooseneck without pulley - 2 pairs WADER container pockets in the platform for a 20ft container - 6 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the platform - Lift axle on the front axle with control via TEBS E, depending on actual axle load and loading condition - 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN) - 1 pair of recessed lashing rings along the central beam at the rear chamfer (LC 10,000 daN) - Sand coating for slip resistance painted on the chequer plates on the gooseneck and on the platform - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and removable pump protection - Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm - Speed stickers 80 km/h rear and on both sides - Load manometer for determining axle loads including load chart - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then all defined visible surfaces metallized and hot-coated with ZINACOR 850 (zinc 85% - alu 15%)

Stanje: novo, skupna masa: 78.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 850 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck in SNT design to optimize loading area length, approx. 3,700 mm long, rear with a bevel approx. 1,000 mm x 10° • For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading Area: • Extendable loading platform, approx. 8,800 mm long with rear bevel approx. 500 mm x 10° • A recess in the platform and rear bevel to accommodate the excavator dipper stick, approx. 3,950 x 580 x 370/450 mm Ramps: • One pair of two-piece steel ramps, approx. 4,350 mm long and 900 mm wide • Hydraulically folding ramp tips • Ramps hydraulically adjustable separately approx. 235 mm outwards and approx. 215 mm inwards • Hardwood decking on the beveled part of the loading area • Ramp with hardwood decking • 20 x 30 mm square climbing strips, approx. every 200 mm on the outer frame of the ramp Axles and Tyres: • TWINAXLE-II independent wheel suspension with BPW stub axles, 1st axle steered in advance, all other axles are hydromechanically forced steered • 1st axle with electromagnetic reverse lock via reverse gear and manual activation • Technical axle load: 12,000 kg • Hydr. axle compensation, hydraulic cylinders with shut-off valves • Tyres 245/70 R 17.5 • TPMS tyre pressure monitoring system according to ECE R 141 Accessories Included: • Plug-in steel front wall, approx. 400 mm high • 4 wheel chocks with holder • Front connection bar with yellow-red air couplings • 3 kW electro-hydraulic power pack for hydraulic control, except for hydraulic winches • 1 spare wheel • 2 pairs of screw-in lashing rings • 1 pair of horizontal lashing rings in the rear area of the gooseneck • On the gooseneck: 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized • On the gooseneck: 1 plug-in ALU rear board, approx. 400 mm high, anodized • Approx. 40 mm thick hardwood decking on the gooseneck, checker plate over the king pin • 3.5" king pin • Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide • Load area locking with conically welded arresting profiles every 250 mm • Incl. pre-tensioning plate Ljdpfx Asrvw U Sedgehi • 1 pair of lashing rings on the front cross member • 8 pairs of recessed, fold-out lashing rings in the outer frame of the platform • Extendable (galvanized) widenings approx. 230 mm per side • 1 pair of fixed open wheel recesses up to extension, approx. 700 x 410 mm, in the platform in front of the 1st axle • Wheel recesses with checker plate covering and 15 x 15 mm square climbing strips, approx. every 200 mm • 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm, in the platform between the 1st and 2nd axle • Wheel recesses with 15 x 15 mm square climbing strips and widenings in the lower section • ALU covers for the wheel recesses between 1st and 2nd axle, which can also be used as broadening planks • 1 pair of mechanical rear supports • 20 x 30 mm square climbing strips, approx. every 200 mm on the outer frame of the bevel of the loading area • Central lubrication system with 1 pump, BEKAMAX brand, standard grease as per NLGI-2 • Radio and cable remote control, with 2 indicator lights on the receiver for single wheel control • WABCO Smart Board system • The Smart Board is equipped with an odometer • 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and mounts for rotating beacon

Stanje: rabljeno, lastna masa: 10.900 kg, največja dovoljena obremenitev: 43.600 kg, skupna masa: 54.500 kg, konfiguracija osi: 3 osi, prva registracija: 04/2025, dolžina tovornega prostora: 8.700 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 855 mm, velikost pnevmatike: 245/70 r17.5, barva: siv, Leto izdelave: 2025, obratovalna teža: 10.900 kg, Oprema: ABS, Gooseneck, rigid, center tube design: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Steel floor with anti-slip coating - Including perforated rail for aluminum approach ramps - 2" king pin - Manually operated BPW landing legs - 550 mm long, 8° chamfer at end of gooseneck - Front wall including park position for rear wall, 400 mm high - Spare wheel holder mounted vertically on the front side of the gooseneck - 3 pairs of recessed lashing rings (LC 5,000 daN) in the loading area of the gooseneck - Aluminum side boards, 400 mm high, comprising 2x side boards each 3,150 mm long, and rear board with stanchions (galvanized) - Rectangular aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, center - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, left - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, right Loading platform, single-extendable: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Fixed section at front 700 mm - Steel plate floor with anti-slip coating - Chamfered transition between fixed part and deck for bridging rails and wheel recesses - Excavator trough including elongated holes for load securing (LC 1,500 daN), length approx. 3,850 mm - Prepared for hydraulic ramps (electrical supply) - Rails to widen up to 3,000 mm - 8° chamfered vehicle rear, 550 mm long - Slide system for easy mounting/dismounting of ramps - Continuous mud flap at the rear - 1 pair of lashing points LC 10,000 daN centrally on the loading area behind the gooseneck - 7 pairs of lashing points LC 10,000 daN in the outer frame of the loading platform - 6 pairs of stanchion pockets 100 x 50 mm in the outer frame of the loading platform - 1 pair of lashing points LC 10,000 daN centrally in the rear section of the loading platform - 1 pair of stanchion pocket rails approx. center of the loading area - 1 pair of stanchion pocket rails on the fixed part - 1 pair of stanchion pocket rails behind the last axle Ramps: - Hydraulic double-folding ramps, 2,750+1,500x800 mm - Larch wood surface - Operated by remote control (wired and wireless) - Quick-change ramp (dismantling system) Chassis: - Axle brand: BPW ECO Max - 2 ride heights - 4 axles @ 10 t (technically 12 t) - Twin tires 245/70 R17.5 - 2 x rigid axles and 2 x friction-steered axles - Reverse steering lock for friction-steered axles via reverse gear - Brake system by Knorr (according to EU standards with EBS-E) - Knorr TIM G2 (Trailer Information Module) - RSS (Roll Stability Support) stability control Lhodpji Ai E Rofx Adgsi - Load-dependent lift axle on the first axle incl. starting aid (forced lowering of lift axle via TIM possible) Accessories: - 4 wheel chocks with holder - 2 pairs of warning panels 423 mm x 423 mm, with 2 position lights and socket for rotating beacon, steplessly adjustable up to 3,950 mm - Securing points on gooseneck and on loading platform (alternatively on ramp, if available) included - Plug-in bulkhead at the end of the excavator trough - Electrohydraulic unit for ramp operation - Ramp control by wireless remote - Hydraulic rear support legs for stabilization during loading - 1 pair of additional reversing lights at the rear, activated when reversing - Larch wood widening planks (option)

Stanje: rabljeno, številka stroja/vozila: YAFSR31200001xxxx, Leto izdelave: 2012, Prosimo, navedite referenčno številko ob povpraševanju: 23457 Specifikacije: Leto modela: 2012 3 osi Dolžina: 1325 cm Lastna teža: 12.178 kg Dovoljena skupna masa: 59.000 kg 12-tonske osi Krmiljenje na vseh oseh Takoj na voljo Opis: 2012 Faymonville Telemax prikolica s fiksno ploščadjo z raztegljivostjo do 27 metrov. Podaljšek znaša 14 metrov. Pripravljeno za dostavo. Tehnični pregled (TÜV): Da EU odobritev do: 28.02.2027 Lhjdpfx Ajzm I Akjdgsi Lastna teža: 12.178 Skupna teža: 59.000 Model: Telemax ravna prikolica z 27 m izvlekom = Dodatne informacije = Za več informacij kontaktirajte ATS Norway.

Stanje: novo, največja dovoljena obremenitev: 48.930 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, Celotno zalogo vozil, vključno z vozili, ki so na voljo takoj in v kratkem roku, najdete na naši spletni strani. Izvleček iz opreme. Popolna oprema na zahtevo. "Gooseneck" prikolica * s poševnimi robovi spredaj, približno 45° in z zadnjim poševnim robom, približno 750 mm x 10° * 3 pari pritrdilnih obročev (nosilnost 5.000 daN) * trdna lesena obloga, debeline približno 30 mm Tovorilna površina * dvodelna, izpodvlačna izvedba z zadnjim poševnim robom, približno 500 mm x 8° * 5 parov pritrdilnih obročev, ki se zunanji prepognejo (nosilnost 5.000 daN) * 4 pari pritrdilnih obročev, ki se zunanji prepognejo (nosilnost 10.000 daN) * 1 par pritrdilnih obročev, nameščenih ležeče na sprednji strani tovorilne površine (nosilnost 10.000 daN) * 1 vmesna miza, približno 250 mm * izrezi v zunanjem okvirju tovorilne površine za pritrditev zategovalnih trakov (nosilnost 2.000 daN) * trdna lesena obloga, debeline približno 48 mm, nad osmi je valjasta kovinska obloga Osi * osi BPW, hidravlično-mehansko sinhronizirano krmiljenje * tehnična nosilnost osi: 12.000 kg na os * zračna vzmetenje z ventili za dvig in spuščanje Pnevmatike * 245/70 R 17.5 3PMSF, indeks obremenitve (146/146 F) * TPMS sistem za nadzor tlaka v pnevmatikah, v skladu s standardom ECE R 141 Opore sedla * JOST opore sedla (mehanske) z dvostopenjsko prestavo za približno 24 t nosilnosti (približno 50 t testna nosilnost) Zavorna naprava * v skladu z direktivami EU z EBS-E (4S3M) Jeklena konstrukcija * iz visoko trdnih finozrnatih jekel * vrste jekel: S355J2+N/S355MC (meja tečenja 355 MPa) * S690QL/S700MC (meja tečenja 690 MPa) Električni sistem * v skladu z direktivami EU, osvetlitev 24 voltov ASPÖCK-NORDIK (ASS3) * vse LED stranske markerne luči utripajo sinhronizirano s smerniki * ASPÖCK-UNIBOX na priključni letev spredaj s vtičnicami 24N, 24S & 15-polni priključek, v skladu s standardom ISO. 24N ISO-1185 24S ISO-3731 15-polni ISO-12098 Barvanje * celotna jeklena konstrukcija, po varjenju, avtomatsko peskana z metodo vrtinčenja * drugo peskanje s korundom za optimalno oprijemljivost prevlečnega sistema * HRM-metalizacija celotnega podvozja vozila z ZINACOR 850 (85% cink/15% aluminij) za zagotovitev najboljše zaščite proti koroziji * končna barva z 2 plastma 2K-lak, enobarvno, v RAL 3002 Karminrot, v skladu s sistemom RAL 841GL Lodpfx Aszlwm Asdgohi * platišča v srebrni barvi. Zadnji del je metaliziran in pobarvan v RAL 9010 (čista bela) * metalizirano barvanje ni mogoče * test barvne strukture izveden v testu meglenega spreja s soljo, v skladu s standardom ISO 9227-NSS * zaščita notranjih prostorov s posebnim voskom Vključno z naslednjo dodatno opremo 2-palčni kraljevi vtič * elektro-hidravlična agregat (± 45 kg) * dodatno krmiljenje od spredaj in od zadaj s kablom, upravljanje s pritiskovnimi gumbi, z nadzorom posameznih osi (brez vgradnje v centralno krmilno enoto) * na "gooseneck" prikolici in na zadnji plošči, na levi in desni strani, držalo za opozorilne table, vključno z vtičnico * držalo za okroglo luč na zadnji strani prikolice * na "gooseneck" prikolici aluminijaste stranske stene in zadnja stena, ki se lahko vstavi, približno 2.440 x 400 mm (D x V) * zadnje pocinkane stranske stene se lahko odstranijo. (dolžina nadgradnje, približno 2.560 mm) (± 46 kg) * orodjarna omara, pocinkana, integrirana v poševno "gooseneck" prikolico (± 47 kg) * 4 pari WADER žepov za zabojnike na tovorilni površini za 20', 2x 20', 40' ali 45' zabojnik (± 40 kg) * 7 parov žepov za stranske stene, približno 100 x 50 mm

Stanje: novo, največja dovoljena obremenitev: 33.865 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, Izpisek opreme Gooseneck prikolica * s poševnimi robovi spredaj, približno 45° in s poševnim zadnjim delom, približno 750 mm x 10° * 3 pari pritrdilnih obročev (LC 5.000 daN) * trda lesena obloga, debeline približno 30 mm Tovorilna ploščad * v dvojni izvlečni izvedbi s poševnim zadnjim delom, približno 500 mm x 8° * 6 parov pritrdilnih obročev, ki se zlagajo navzven (LC 5.000 daN) * 4 pari pritrdilnih obročev, ki se zlagajo navzven (LC 10.000 daN) * 1 par pritrdilnih obročev, nameščen vodoravno na sprednji strani tovorilne ploščadi (LC 10.000 daN) * 1 vmesna miza, približno 250 mm * trda lesena obloga, debeline približno 48 mm, nad osmijo obloga iz valjane pločevine * izrezi v zunanjem okvirju tovorilne ploščadi za obešanje napenjalnih trakov (LC 2.000 daN) Osi * BPW osi in vzmetenje, vse osi hidro-mehansko sinhronizirane * maksimalna tehnična obremenitev osi: 12.000 kg na os * zračno vzmetenje z ventilom za dvig in spuščanje * orodje za osi Lhedpfx Aezlwm Nsdgji Pnevmatike * 245/70 R 17.5, indeks nosilnosti (146/146 F) * proizvajalec po naši izbiri Podporne noge * JOST podpore (mehanske) z dvostopenjskim menjalnikom za približno 24 t dvigalne nosilnosti (približno 50 t preizkusne nosilnosti) Zavorna sistem * v skladu z direktivami EU, z EBS-E (2S2M) brez priključnih kablov do vlečne enote Barvanje * vrhunsko in dolgotrajno protikorozijsko zaščito standardno kroglično peskane jeklene konstrukcije zagotavlja dvokomponentna (2K) temeljno prevleka s cinkovim prahom * vrhunska dvokomponentna (2K) * zaključna barva, enobarvna, v RAL 3002, karminsko rdeča * zadnji del je metaliziran in pobarvan v RAL 9010 (čista bela) * metalizirano barvanje ni mogoče Jeklena konstrukcija * iz visoko trdnih finozrnatih jekel * kvalitete jekla: S355J2+N/S355MC (meja tečenja 355 MPa) S690QL/S700MC (meja tečenja 690 MPa) Električni sistem * v skladu z direktivami EU * razsvetljava 24 voltov ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX na sprednji priključni letev z vtičnicami 24N, 24S in 15-polno * priključki v skladu s standardom ISO. 24N ISO-1185, 24S ISO-3731, 15-polni ISO-12098 Vključno z naslednjo dodatno opremo * 2 palčni kraljevi člen (King pin) * pocinkana jeklena sprednja stena, približno 400 mm visoka * rumeno-rdeči zračni spojniki na pocinkani sprednji priključni letvi * 4 kosi zavorne podloge z nosilcem na sprednji steni (± 5 kg) * nosilec za rezervno kolo pred sprednjo steno * elektro-hidravlična enota (± 45 kg) * naknadno usmerjanje od spredaj in zadaj s pomočjo kabelskega daljinskega upravljanja, upravljanje z gumbi, z nadzorom osi (brez vgradnje v vlečno enoto) * nosilec na zadnjem delu gooseneck prikolice za aluminijaste nakladalne rampe * evropski reflektorski znaki (rdeče-rumeni) na zadnji strani prikolice * rumeno reflektorsko trakom v skladu z direktivami EU, stransko, na izvlečni strani in na zadnji strani prikolice * na gooseneck prikolici in na zadnji plošči, na levi in desni strani, nosilec za opozorilne table, vključno z vtičnico * priključna letev za aluminijaste nakladalne rampe na zadnji strani vozila * nosilec za okroglo rotacijsko luč na zadnji strani prikolice * pocinkane zložljive podpore pod poševnim delom tovorilne ploščadi * zaščitnik blatnikov na zadnji strani prikolice * navodila in opis na USB-ključu * nalepka za omejitev hitrosti 80 km/h na zadnji in na obeh stranskih straneh * manometer za obremenitev osi za ugotavljanje obremenitve osi, vključno s diagramom obremenitve.

Stanje: novo, največja dovoljena obremenitev: 46.800 kg, skupna masa: 58.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, Na naši spletni strani najdete naš celoten nabor vozil, ki so na voljo takoj ali v kratkem roku. Izbor iz opreme: Celotna oprema na zahtevo. "Labodje vrat": * "Labodje vrat" s poševnimi robovi spredaj, približno 45° in z zadnjo poševnostjo približno 750 mm x 10° * 3 pari pritrdilnih obročev (nosilnost 5.000 daN) * Prevleka iz trdega lesa, debeline približno 30 mm Nosilna plošča, raztegljiva različica: * z zadnjo poševnostjo približno 1.000 mm x 8° * 5 parov pritrdilnih obročev, z zunanjim mehanizmom za zlaganje (nosilnost 5.000 daN) * 3 pari pritrdilnih obročev, z zunanjim mehanizmom za zlaganje (nosilnost 10.000 daN) * 1 par pritrdilnih obročev, nameščen vodoravno spredaj na nosilni plošči (nosilnost 10.000 daN) * Vrezanine v zunanjem okvirju nosilne plošči za pritrditev zategovalnih trakov (nosilnost 2.000 daN) * Prevleka iz trdega lesa, debeline približno 48 mm, nad osmi protizdrsna prevleka. Osi: * Osi in vzmetenje BPW * Prva os je fiksna, vse ostale osi pa so hidravlično-mehansko sinhronizirane Ljdpfx Adezk S Dmsgshi * Tehnična obremenitev osi: 12.000 kg na os * Zračno vzmetenje z ventilom za dvigovanje in spuščanje * Orodje za osi * Pnevmatike * 245/70 R 17.5 3PMSF * Indeks obremenitve (146/146 F) * TPMS: Sistem za nadzor tlaka v pnevmatikah, v skladu s standardom ECE R 141 Podporne noge * Podporne noge JOST (mehanske) z 2-stopenjsko prestavo za približno 24 t dvigalne nosilnosti (približno 50 t preizkusne nosilnosti) Zavorna naprava * v skladu s predpisi EU z EBS-E (4S3M) Barvanje * Celotna jeklena konstrukcija, avtomatsko obdelana s peščanjem po varjenju * Drugo peskanje s korundom za optimalno oprijemljivost prevlečnega sistema * HRM-metalizacija celotnega šasije vozila s pomočjo ZINACOR 850 (85 % cink/15 % aluminij) za zagotavljanje najboljše korozijske zaščite * Končno barvanje z 2 plastmi 2K lakom * enobarvno, v barvi RAL 3002 Karminrot, v skladu s sistemom RAL 841GL * Platišča v srebrnosivi barvi. Zadnji del metaliziran in pobarvan v barvi RAL 9010 (čista bela) * Metalizirano barvanje ni mogoče * Barvna prevleka preizkušena s testom solne megale v skladu s standardom ISO 9227-NSS * Zapiranje votlin s specialnim voskom Jeklena konstrukcija * iz visoko trdnih finozrnatih jekel * Kakovost jekla: S355J2+N/S355MC (meja tečenja 355 MPa), S690QL/S700MC (meja tečenja 690 MPa) Električni sistem * v skladu s predpisi EU Osvetlitev * 24 Volt ASPÖCK-NORDIK (ASS3) * Vse LED stranske gabaritne luči utripajo skupaj s smerokazom * ASPÖCK-UNIBOX na priključni letev spredaj s vtičnicami 24N, 24S & 15 polna * Priključek v skladu z ISO. 24N ISO-1185 24S ISO-3731 15 polna ISO-12098 Vključno z naslednjo dodatno opremo: * 2-palčni kraljevi priklop * Pocinkana jeklena sprednja stena, približno 400 mm visoka * Elektro-hidravlična agregat (± 45 kg) * Pomik sprednje in zadnje osi s kabelskim daljinskim upravljanjem preko tipk, z nadzorom ene osi (brez vgradnje v centralno mazalno enoto) * 1 par potopljenih pritrdilnih obročev vzdolž centralnega nosilca zadaj v poševnem delu (nosilnost 10.000 daN) (± 3 kg) * Na "labodjem vratu" aluminijaste bočne stene in zadnja stena, vstavljivi, približno 2.440 x 400 mm (D x V) * Zadnje pocinkane vstavne ograje je mogoče odstraniti. (dolžina nadgradnje približno 2.560 mm) (± 46 kg) * Orodje, galvanizirano, integrirano v poševni del "labodjega vrata" (± 47 kg) * 3 pari WADER žeepov za kontejnerje na nosilni plošči za 20' (30?) ali 40'? kontejner (± 30 kg) * 6 parov žeepov za vstavne ograje, približno 100 x 50 mm, v zunanjem okvi

Stanje: rabljeno, največja dovoljena obremenitev: 47.300 kg, skupna masa: 58.000 kg, konfiguracija osi: 3 osi, prva registracija: 03/2025, naslednji pregled (TÜV): 03/2026, Oprema: ABS, Izpisek iz opreme. Celotna oprema na zahtevo. * Vratna plošča s poševnimi robovi spredaj, približno 45° in s poševnim zadnjim delom, približno 750 mm x 10°. * 3 pari pritrdilnih obročev (LC 5.000 daN) * Trdna lesena obloga, debeline približno 30 mm. * Nosilna površina v izvlečni izvedbi s poševnim zadnjim delom, približno 1.000 mm x 8°. * 5 parov pritrdilnih obročev, zložljivih navzven (LC 5.000 daN) * 3 pari pritrdilnih obročev, zložljivih navzven (LC 10.000 daN) * 1 par pritrdilnih obročev, nameščenih vodoravno spredaj na nosilni površini (LC 10.000 daN) * Izrezi na zunanjem okvirju nosilne površine za pritrditev zategovalnih trakov (LC 2.000 daN) * Trdna lesena obloga, debeline približno 48 mm, nad osmi. * Rebrasta jeklena obloga. * Podporne noge sedelne prikolice JOST podpore (mehanske) z 2-stopenjsko prestavo za nosilnost 24 t (preskusna nosilnost 50 t) * Pnevmatike 235/75 R 17.5 3PMSF * Osi BPW osi, dve fiksni osi, dve osi s sledilnim sistemom, z zračno vzmetjo, z bobnasto zavoro s funkcijo dviganja/spuščanja. Sledilne osi z elektromagnetno blokado za vožnjo v vzvratni smeri, ki se aktivira preko vzvratne prestave ali ročno. * Zavorna naprava WABCO zavorna naprava v skladu z direktivami EU, z EBS-E (4S3M) brez povezovalnih vodov do vlečne enote. * Lakiranje Kakovostno 2-komponentno (2K) lakiranje, enobarvno, v barvi RAL 3002, karminsko rdeča. * Dodatna oprema Nosilec za rezervno kolo pred sprednjo steno (brez rezervnega kolesa). 2-palčni kraljevi zatič. Pocinkana jeklena sprednja stena, približno 400 mm visoka. Na pocinkani priključni letev spredaj so nameščene rumeno-rdeče zračne spojke. 4 klini s pritrdilom na sprednji steni. Nosilec na zadnjem delu vratne plošče za aluminijaste dostavne rampe. Lhedpfx Aszkx Huodgji Pocinkane zložljive podpore pod poševnim delom nosilne površine. Nosilec za okroglo luč na zadnjem delu prikolice. Rumena odsevna trak v skladu z direktivami EU, stransko, na izvlečnem delu in na zadnjem delu prikolice. Na vratni plošči in na zadnji plošči, na levi in desni strani, nosilci za opozorilne table, vključno z vtičnico. Merilnik obremenitve za ugotavljanje obremenitve osi, vključno z grafom obremenitve. * Vključno s posebno dodatno opremo Na vratni plošči so aluminijaste bočne stene in zadnja stena, ki se lahko pritrdijo, približno 2.440 x 400 mm (D x V). Galvaniziran orodjarni predal, integriran v poševno vratno ploščo. 3 pari WADER pritrdilnih vreč na nosilni površini za 20' (30') ali 40' kontejner. Drseče pritrdilne letev za aluminijaste dostavne rampe na zadnjem delu vozila. 6 parov pritrdilnih vreč za vstavne prečke, približno 100 x 50 mm, na zunanjem okvirju nosilne površine. Pocinkane razširitve, izvlečne, približno 230 mm na stran. Dvignjena os na sprednji osi z upravljanjem preko TEBS E. 2 LED vzvratni svetili, nameščeni na zadnji plošči. 2 para Ferry obročev pod vratno ploščo in 2 para zadaj. Akustični opozorilni signal pri vožnji v vzvratni smeri. HRM metalizacija (metalizacija z visoko odpornostjo).

Stanje: rabljeno, konfiguracija osi: 3 osi, prva registracija: 01/2012, skupna dolžina: 13.700 mm, skupna širina: 2.550 mm, skupna višina: 3.300 mm, vzmetenje: zrak, velikost pnevmatike: 245/70 R17.5, barva: drugo, Leto izdelave: 2012, Oprema: ABS, = Additional Options and Accessories = - Drum brakes = Remarks = Ledpsx U D Aljfx Adgshi Chassis Diameter of kingpin / fifth wheel: 2 inch Height of kingpin / drawbar: 120 cm Drum brake: ✓ Special transport 2-piece road plates: ✓ Hydraulic ramps: ✓ Length over axles: 900 cm Platform length: 900 cm Gooseneck length: 360 cm Maximum width: 290 cm (250+20+20) Extendable: × = Further Information = Axle configuration Tire size: 245/70 R17.5 Axle brand: SAF Brakes: Drum brakes Suspension: Air suspension Front axle: Twin tires; Tire tread left inside: 40%; Tire tread right inside: 25% Middle axle: Twin tires; Tire tread left inside: 50%; Tire tread right inside: 40% Rear axle: Twin tires; Tire tread left inside: 15%; Tire tread right inside: 25% Weights Unladen weight: 11,000 kg Payload: 37,000 kg Gross vehicle weight: 48,000 kg Identification Registration number: C340521 = Company Information = For more information on this unit please call: or e-mail: . A full stock overview can be found at: . Please do not forget to subscribe to our newsletter for weekly updates on our stock.

Stanje: novo, največja dovoljena obremenitev: 98.290 kg, skupna masa: 126.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, You can find our entire range of vehicles that are immediately and soon available on our website. Extract from the equipment list. Full equipment details available on request. Gooseneck: * MAX810-neck-V-30-2.70-2{DSR 2 700/ASH 1300->1400} * Gooseneck hydraulically liftable/lowerable as well as removable. Length approx. 3,650 mm * Truck hydraulic connection with flow controller (20 l/min), * incl. gallows for suspension of supply lines, tractor unit (SZM) tank must hold at least 80 l, with MAX Trailer coupling pieces; otherwise, coupling pieces to be provided by the customer ex works. * For tractor units: 6 x 4 or 8 x 4 Loading Platform MAX810-6-A-11.00-17.5-1.50-2.75-PA-X * 6-axle extendable loading platform with pin-lug coupling at the front and approx. 500 mm x 8° chamfer at the rear. * Length: approx. 11,000 mm * Technically extendable by: approx. 7,700 mm * Axle spacing: approx. 1,500 mm Ljdpfx Aezbfuhsdgshi * Hydraulic coupling bolt. Pendulum axle 2-axle front running gear, pendulum axle * All axles are hydromechanically forced steered. * MAX810-chassis-PA-X-F-2-17.5-1.50-2.75 pin-lug coupling front and rear. * Length: approx. 2,970 mm, chassis width: approx. 2,750 mm * BEKA-MAX central lubrication for a 2-axle running gear with standard grease NLGI-2 * Extendable widenings of approx. 230 mm per side for a 2-axle running gear. (± 27 kg) PENDULUM AXLE 6-AXLE LOADING PLATFORM, PENDULUM AXLE * All axles hydromechanically forced steered. * Hose burst valve on the axle compensation cylinder with automatic reset function. * Hydraulic cylinders with shut-off valves and pre-pin for securing in raised position. * Technical axle load: 13,740 kg each (30 km/h) * Hydraulic axle compensation. TYRES * 24 x manufacturer of our choice (M+S) 245/70 R17.5 * Load index 143/141L (146/146F) * TPMS: TPMS tyre pressure monitoring system in accordance with ECE R 141. Final coating of the axles * Painted with two coats of single-colour 2-component paint in DB7350 nova grey. * PAINTING Complete steel structure automatically blasted with shot blasting system after welding. * Second blast processing with corundum for optimal adhesion of the coating system. * HRM-metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure the best corrosion protection. * PAINTING Trailer carmine red (RAL 3002) Including the following accessories * Gallows with winch for spare wheel at the front of the gooseneck. * 3.5 inch king pin * Steel front wall approx. 400 mm high. * Plug-in ALU side boards and rear wall on the gooseneck, approx. 400 mm high, anodized version. * Control lever on the gooseneck protected by a foldable cover. * Lighting of the controls on the gooseneck with on/off switch. * One 7-pin socket left and right rear on the gooseneck for the warning sign. * Load gauge on the gooseneck for axle load determination on the running gear at front and rear * BEKA-MAX central lubrication for a gooseneck with standard grease NLGI-2. * Hydraulic connections from the gooseneck to the low bed with screw couplings. * Access possibility on the gooseneck. * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery. Output: 9.5 kW (12.9 HP) at 3000 rpm, emission level: EU Stage V, max. hydraulic pressure: 280 bar, max. flow: 21 l/min, installation on the gooseneck. * Hydraulic oil tank 100 L, frame hot-dip galvanized (± 480 kg) * Hydraulic connection lines between powerpack and plug-in plate on the gooseneck. * Radio remote contr

Stanje: novo, lastna masa: 9.600 kg, največja dovoljena obremenitev: 53.400 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 12.400 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.340 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22.5, barva: siv, Oprema: ABS, Platform area: - Platform with approx. 30 mm thick hardwood flooring - 10 pairs of folding lash rings (outward folding) Landing legs: - JOST landing legs with 2-speed gearbox, 24 t lifting capacity Axles and tyres: - BPW axles, technical capacity 10,000 kg per axle; first axle fixed, all other axles hydro-mechanically forced-steered, mounted on turntables - Air suspension with raise/lower valve - Axle tools included Lsdorq Dlfopfx Adgohi - Tyres: 385/65 R22.5 Braking system: - WABCO brake system in accordance with EU regulations, with EBS-E (4S3M) Steel construction: - Steel structure made from high-tensile fine-grained steels - Steel grades: - S355J2+N / S355MC - S690QL / S700MC Electrical system: - Electrical system according to EU regulations, 24 Volt lighting - ASPÖCK-UNIBOX on the front connection rail with 24N, 24S and 15-pin sockets - Connections according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - First-class and durable corrosion protection of the standard shot-blasted welded frame is ensured by a 2-component zinc-dust primer - High-quality 2-component topcoat, single-colour in Nova Grey - Rear section metallized and painted in RAL 9010 Accessories included: - Platform with approx. 30 mm thick hardwood flooring - 2" king pin - One galvanized steel front wall approx. 1,200 mm high, EN12642-XL - Yellow-red air couplings at the galvanized connection rail at the front - 4 wheel chocks with holders on the front wall - Storage for 1,000 mm plug-in stanchions in the rear central beam - On the gooseneck and rear panel, left and right, a mounting bracket for warning signs with socket - Remote steering from front and rear, operated via cable remote control with push-buttons; with axle tracking control - Electro-hydraulic power pack - White reflective tape as per EU regulations along the side of the trailer, red at rear - 12 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the load bed - European reflective plates at the trailer rear - One bracket for a rotary beacon at the rear of the trailer - One mudflap at the trailer rear - Manual and documentation on USB stick - Central lubrication system BEKAMAX (Pico) with standard NLGI-2 grease and removable protector for the pump - TPMS tyre pressure monitoring system: - The towing vehicle must be capable of transmitting and displaying these data for correct readout - Lift axle on the front axle, automatically controlled by TEBS E in accordance with current axle load and trailer loading status - Radio remote control for the remote steering in addition to the cable remote, with indicator lamps on the receiver for axle tracking control - 5 pairs of crosswise stanchion pocket strips on the bed for 100 x 50 mm plug-in stanchions - 80 km/h speed stickers at rear and both sides - Adjustable access ladder mounted left and right in direction of travel - 2 reversing lights mounted at the rear panel - Load gauge for determining axle loads, including load diagram - HRM metallization of the outer frame: complete steel structure shot-blasted, then all designated visible areas hot metalized with ZINACOR 850 (Zinc 85% - Aluminum 15%)

Stanje: novo, lastna masa: 12.900 kg, največja dovoljena obremenitev: 34.100 kg, skupna masa: 47.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 350 mm, vzmetenje: drugo, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 12.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm in length - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2, and 6x4 Loading Platform: - Low-bed with external beams, extendable “SUPER LOW” design, approx. 6,850 mm in length - Low-bed with fixed hardwood flooring, approx. 40 mm thick, with mechanical locking device Rear Chassis: - Rear chassis with closed outer frame, chequer plate covering, and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings, foldable to the outside - 1 pair of lashing rings recessed in the trough - 2 pairs of stake pockets for insertable stakes 100 x 50 mm in the external frame Pendulum Axle and Tyres: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and safety locking pins for securing in raised position - Axles painted with two layers of single-colour 2K paint in “FAY-Grey-34-0260” Lhodpfx Adjhlz R Ssgsi - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 - TPMS tyre pressure monitoring system according to ECE R 141 Accessories: - Preparation for the installation of bolt-on container locators for 1 x 20ft or 1 x 40ft container on the outer girders - 2" king pin - One galvanized steel front wall, approx. 400 mm high - One spare wheel - Yellow-red air couplers on the galvanized front connection bar - 4 wheel chocks - Remote steering from front and rear, operable via wired remote control with push buttons, with single-track alignment control - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of screw couplings - Electro-hydraulic power unit - White reflective tape in accordance with EU regulations on sides, extension, and rear - European reflective plates (red-yellow) on the rear of the trailer - One bracket on each side of gooseneck and rear plate for warning panels, including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on outer beam for mounting screw-on RUD Rings VLBG-4 - Detachable ALU side boards and rear board on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized insertable stakes are removable (body length approx. 2,560 mm) - Gooseneck rear upper area covered with removable cover - 5 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading area - Folding extensions, approx. 230 mm per side - 2 pairs of bolted RUD Rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the mounting hooks of the low-bed - Anti-skid sand layer painted on loading surface - 80 km/h speed stickers at rear and both sides - Spoon boom trough at rear chassis closed at rear with plug-in plate - Four extendable warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for rear axle steering in addition to cable remote, with indicator lights on receiver for alignment control - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard NLGI-2 grease - Load pressure gauge for determining axle loads - HRM Metallisation (High Resistance Metallisation) of outer frame - Complete steel structure shot blasted, then all defined visible areas metallized and finished with ZINACOR 850 (zinc 85% - aluminium 15%) hot galvanizing

Stanje: novo, lastna masa: 15.450 kg, največja dovoljena obremenitev: 65.550 kg, skupna masa: 80.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 21.900 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 925 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimized platform length, approx. 3,700 mm long, with rear tapering of approx. 1,000 mm x 10° Technical fifth wheel load: 30,000 kg. For tractors: 4x2, 6x2, and 6x4 Loading Platform: Double-extendable loading platform, approx. 8,800 mm long with rear taper of approx. 500 mm x 10°. A support table approx. 300 mm wide is welded to the central beam, featuring elongated slots at the front and rear for optional bridge elements that can be hooked in and repositioned Pneumatic locking with conical locking pin and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles and Tyres: BPW axles and suspension, first axle self-steering, all other axles hydraulically and mechanically forced-steered First axle equipped with an electro-magnetic reverse lockout, activated via reverse gear and manually. Technical axle load: 12,000 kg. Air suspension with lift and lower valve Manufacturer by our choice Lhsdpjrigw Rofx Adgei Sockets and Lighting: 24-volt lighting system in accordance with EU regulations ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Complete HRM metallizing Full steel construction, shot-blasted, then hot-finished with ZINACOR 850 Paintwork: 6-stage finishing process: Complete steel construction shot-blasted after welding 1 coat of zinc-based primer, 1 coat of adhesion primer. Final paintwork in 2 coats of 2K paint in single-tone DB 7350 Novagrau, followed by cavity sealing with special wax Accessories: Detachable front wall made of steel, approx. 400 mm high Connection strip for supply lines to the tractor unit, fitted at the height of the outer frame profile ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets. If your pin configuration deviates from the ISO connector standard, please inform us 3 kW electro-hydraulic power unit for hydraulic functions (excluding hydraulic winches) 1 pair of plug-in ALU sidewalls on the gooseneck, approx. 400 mm high, anodized finish 3.5'' king pin. Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide 2 wheel chocks with holder in front of the front wall Mechanical landing legs with 2-speed gearbox and crank Control valves for hydraulic ramps located on the right side of the vehicle 1 pair of mechanical rear supports Central lubrication system with 1 pump, BEKAMAX brand, using standard grease according to NLGI-2 Removable guard covering the pump(s) of the central lubrication system Remote steering from front and rear, controlled by cable remote with push buttons, with axle tracking control, no installation required on tractor unit Under the gooseneck and on the rear crossmember, one 7-pin socket with holder for warning signs each on left and right. One 7-pin socket on the rear crossmember Manual and documentation One-piece INOX stowage box, approx. 2,480 x 340 x 390 mm, straight design Please note that any special equipment and accessories will increase the unladen weight and correspondingly reduce the payload Warning package: 4 warning boards, approx. 423 x 423 mm, extendable by approx. 1,000 mm, incl. 2 LED position lights and brackets for beacon.