Fliegl Vts 400 Tieflader Mit Radmulden Luft/ Hydr. nakup rabljenega (15.346)

Stanje: novo, največja dovoljena obremenitev: 30.310 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, NEW VEHICLE Fliegl 4-axle low loader with 2 pairs of wheel recesses and ramps Gross weight: 40,000 kg Payload: 30,310 kg Unladen weight: 9,690 kg Overall length: 12,000 mm Loading length: 10,000 mm Loading bed: 7,150 mm including 850 mm drive-on slope Hedpsnzlg Dofx Ag Ijnl Loading height: 900 mm 1st pair of wheel recesses after drop in the loading bed, length at bottom approx. 1,600 mm, 400 mm deep 2nd pair of wheel recesses between the axles in the loading bed, length at bottom 600 mm, 300 mm deep Extensions to 3,000 mm, warning boards, rotating beacon, comprehensive lashing package 5 pairs of stake pockets in the outer frame Excavator arm recess, 1,800 mm long, 150 mm deep Drawbar 50 mm Air suspension with raise/lower valve, separately operable BPW drum brakes Tyres: 235 / 75 R 17.5" Axle load detection via EBS CAN bus signal, Trailer Info Center Ramps: 2,800 mm x 750 mm, hydraulically operated Hydraulic lateral displacement Hire purchase offer: term 48 months, residual value 40%, down payment only the VAT on the installments, monthly payment EUR 970.00 net Vehicle available from 11.09.2023 from the Neumünster trade fair. Visit us at Nordbau - Stand West 121, right next to the main entrance. Further 3-, 4- and 5-axle low loaders new and used available immediately

Stanje: novo, največja dovoljena obremenitev: 30.010 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 10.000 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, New vehicle: Fliegl 4-axle low-loader trailer with wheel recesses and split ramps, type VTS 400 RM Lease-purchase offer: Term 48 months, down payment only the VAT, residual value 40% Monthly rate: EUR 899.00 Vehicle / Body: Low-loader First registration: New vehicle Gross weight: 24,000 kg / 40,000 kg Unladen weight: 9,990 kg Payload: 14,010 kg / 30,010 kg Overall length: 12,000 mm Loading length: total approx. 10,000 mm, gooseneck approx. 2,850 mm, load area including rear bevel approx. 7,150 mm Width: 2,550 mm Loading height: 900 mm Further information Low-loader trailer chassis Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear supports Wheel chocks with holders Aluminum side underrun protection Rear spray flap across the entire width Half-shell mudguards on 1st and 2nd axle with anti-spray flaps behind each axle, anti-spray flap behind 4th axle Excavator arm recess above the rear axles, extending to the rear, approx. 1,800 mm long, approx. 650 mm wide, and approx. 150 mm deep 2 pairs of lashing holes (5 t each) in the excavator arm recess, lateral on the main frame approx. 300 mm from the front and approx. 200 mm before the rear bevel Spare wheel carrier for 1 spare wheel, upright on the gooseneck right at the front. Spare wheel, make identical to the main tires, steel rim Storage box recessed in the gooseneck floor with lid; dimensions W = 720 mm / L = 520 mm / D = 170 mm 1st pair of wheel recesses after the gooseneck, recessed in the low-bed lane area, ramped for entry, bottom length approx. 1,600 mm, depth approx. 400 mm. Note: Frame in the main beam area is 400 mm higher than the wheel recess 2nd pair of wheel recesses between the axles, recessed in the low-bed lane area, ramped for entry, bottom length approx. 600 mm, depth approx. 300 mm. Note: Frame in the main beam area is 300 mm higher than the wheel recess Extendable width up to 3,000 mm (not extendable in the rear bevel and not in the lower wheel recesses) (track width of the construction equipment or vehicles to be transported must not exceed the external frame width of 2,550 mm) Storage compartment for wooden planks below the low-bed area 70 mm wooden planks for extension to 3,000 mm Hsdpfxetrizkj Ag Isnl Lashing eyes on the low-loader 1 pair of lashing eyes, recessed in the front of the gooseneck, 5 t each 4 pairs of lashing holes in the outer frame, 5 t each (for lashing straps) 8 pairs of lashing rings, integrated on top and side of outer frame, 10 t each 2 at the front on the gooseneck 6 in the low bed First lashing point 250 mm from the front and last max. 250 mm from the rear, spacing between lashing points not greater than 1,100 mm 5 pairs of stake pockets integrated in the outer frame, inside 70 x 40 mm (convertible to 5 t ring lashing eyes, not included) 1 pair of folding lashing eyes, additionally recessed in the floor, 10 t each 1 inside next to the main frame at the start of the low bed 2 pairs of additional folding lashing eyes, 10 t each 1 on the gooseneck (protrudes over edge) 1 behind last axle, recessed in floor Drawbar coupling / turntable trailer hitch Towing bar with certified 50 mm towing eye, towing eye inclined 8° D-value at least 160 kN Axles & suspension BPW drum brake axles "Axle/chassis laser alignment" reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical front axle load equalization (rocker balance) Wheels and tires 235 / 75 R 17.5" Manufacturer's choi

Stanje: novo, največja dovoljena obremenitev: 31.920 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 10.410 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, New vehicle: Fliegl 4-axle low-loader trailer with ramps, model VTS 400 Gross weight: 24,000 kg / 40,000 kg Unladen weight: 8,080 kg Payload: 15,920 kg / 31,920 kg Overall length: 11,940 mm Loading length: total approx. 10,410 mm; neck approx. 2,490 mm; loading bed incl. rear taper approx. 7,920 mm Width: 2,550 mm Loading height: 900 mm Further information: Plus pre-freight / preparation ex stock 26639 Wiesmoor: €1,280.00 / net Chassis: Low-bed trailer Steel welded construction Turntable with heavy-duty ball race ring Foldable rear support 2 wheel chocks with holders Side underrun protection, aluminium Full-width rear mud flap Half-shell mudguards, 1st and 2nd axles with anti-spray flaps behind each axle, Anti-spray flaps in front of and behind 3rd and 4th axles Excavator stick trough over rear axles to the rear, approx. 1,800 mm long, 650 mm wide, 150 mm deep 2 pairs of lashing holes, each 5 t, in the excavator stick trough on the longitudinal frame, approx. 300 mm from the front and 200 mm in front of the rear slope 1 plastic toolbox, w=600 mm / h=425 mm / d=460 mm, lockable Storage box recessed in the neck floor with lid, w=720 mm / l=520 mm / d=170 mm Extendable outriggers to 3,000 mm (not for rear slope) (Track width of construction machinery/vehicles to be transported must not exceed external frame width of 2,550 mm) Storage compartment for wooden planks under the low-bed deck Wooden planks, 70 mm, for extension to 3,000 mm Lashing points, low-loader: 1 pair of lashing cutouts in the front longitudinal beams, embedded in the neck, each 10 t 4 pairs of lashing holes in the outer frame, each 5 t (for attaching ratchet straps) 9 pairs of lashing mushrooms, embedded in and above the outer frame, each 10 t: - 2 × on the neck - 7 × in the low-bed section First lashing point 250 mm from the front, last max. 250 mm from the rear; lashing point spacing max. 1,100 mm Additionally, 3 pairs of folding lashing eyes, each 10 t: - 1 × on the neck (protruding) - 1 × at the start of the low-bed inside the longitudinal beams - 1 × in the floor behind the last axle Drawgear, turntable trailer: Drawbar with certified 50 mm eye Drawbar height adjustment via spring Axles & Suspension: Drum brake axles, per manufacturer’s choice "Axles/chassis laser-aligned" to reduce tire wear and fuel consumption Air suspension with lift & lower valve + auto-reset function Wheels and Tyres: 235 / 75 R 17.5", per manufacturer’s choice Steel twin wheels, factory silver Braking system: 2-line air-operated brake system Spring-loaded parking brake Axle load detection via EBS CAN bus signal for display in truck cab (truck must be equipped accordingly; not a calibrated scale) Vehicle stability system: Hnjdpfxexrx Nle Ag Iol 2 non-interchangeable coupling heads at the front, connection lines to the tractor 12-24V EBS, electronic braking system with EBS socket at the front, including connecting cable (Knorr brand) Attention: The trailer may only be towed by vehicles that guarantee ABS functionality! Electrics: 12-24V, multi-chamber LED lights, side LED marker lights (yellow), LED license plate lighting (Note: Some towing vehicles may display incorrect errors despite proper function) 2 white front position lights, LED 2 white/red rear lane marker lights, LED 2 × 7-pin non-interchangeable sockets at the front, with connection cable 1 LED rotating beacon with bracket, switchable via sidelights (removable beacon) 2 pairs...

Stanje: novo, največja dovoljena obremenitev: 31.920 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 10.410 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, New Fliegl 4-Axle Low Loader Trailer with Ramps, Model VTS 400 Gross weight: 24,000kg / 40,000kg Unladen weight: 8,080kg Payload: 15,920kg / 31,920kg Total length: 11,940mm Total loading length: approx. 10,410mm; Gooseneck: approx. 2,490mm; Loading platform incl. rear bevel: approx. 7,920mm Width: 2,550mm Loading height: 900mm Additional information plus delivery/preparation from stock location 26639 Wiesmoor: €1,280.00 net Leasing offer: term 48 months, down payment only VAT, residual value 40% Hodsvv D Ixjpfx Ag Ienl Monthly instalment EUR 759.00 Chassis Low Loader Trailer Steel welded construction Turntable with heavy-duty ball-bearing slewing ring Foldable rear support 2 wheel chocks with holders Aluminium side underrun protection Full-width rear spray flap Half-shell mudguards on axle 1 + 2 with anti-spray flaps behind each axle Anti-spray flaps before and behind axles 3 and 4 Excavator arm recess over rear axles, stretching to the rear, approx. 1,800mm long, 650mm wide, 150mm deep 2 pairs of lashing holes (5t each) in the excavator arm recess, side-mounted on the longitudinal frame, approx. 300mm from the front and approx. 200mm before the rear bevel 1 plastic toolbox, w=600mm / h=425mm / d=460mm, lockable Storage box recessed into the gooseneck floor with lid, w=720mm / l=520mm / d=170mm Extendable widenings to 3,000mm (not at rear bevel) (Note: the track width of machines or vehicles being transported must not exceed the outer frame width of 2,550mm) Wooden plank compartment under the low-bed platform 70mm wooden planks for extension to 3,000mm Low loader lashing points 1 pair of lashing cutouts sunk in the longitudinal beam at the front of the gooseneck, 10t each 4 pairs of lashing holes in external frame (5t each, suitable for tension belt attachment) 9 pairs of lashing mushrooms set into the external frame above and on the sides, each 10t 2x front on gooseneck 7x low-bed area 1st lashing point 250mm from front, last max. 250mm from rear, max distance between lashing points 1,100mm 3 additional pairs of folding lashing eyes, 10t each: - 1x on gooseneck (protruding) - 1x inside start of low-bed area in longitudinal beams - 1x recessed in floor behind last axle Towing arrangement, turntable trailer Drawbar with certified 50mm draw eye Drawbar height adjustment via spring Axles & Suspension Drum brake axles, manufacturer’s choice Chassis/axle laser alignment (reduces tyre wear and fuel consumption) Air suspension with raise & lower valve + auto reset function Wheels and tyres 235/75 R 17.5”, manufacturer’s choice Steel twin wheels, factory silver Braking system 2-line pneumatic brake system Spring-loaded parking brake Axle load detection via EBS CAN-Bus signal (for in-cab display, truck must be pre-equipped, not a calibrated scale) Vehicle stability system 2 foolproof coupling heads at the front, with connecting lines to tractor unit 12-24V EBS (Electronic Braking System) with EBS plug at the front and connecting cable (Knorr brand) Note: Trailer must only be towed by towing vehicles capable of ensuring full ABS functionality! Electrics 12-24V, multi-chamber LED lamps, amber LED side markers, LED license plate lighting (Note: On certain tractor units, malfunction messages may appear even if operational) 2 white position lights at the front (LED) 2 white/red contour marker lights at the rear (LED) 2x 7-pin foolproof connectors at the front

Stanje: novo, največja dovoljena obremenitev: 31.100 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 10.410 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.520 mm, Gross weight: 24,000kg / 40,000kg Curb weight: 8,900kg Payload: 15,100kg / 31,100kg Total length: 11,940mm Loading length: 10,410mm total, 2,490mm gooseneck, 7,920mm loading deck including rear bevel Width: 2,520mm Loading height: 900mm Further information: plus pre-carriage / provision ex stock location 26639 Wiesmoor: €1,280.00 net Steel welded construction Turntable with heavy-duty ball-bearing slewing ring Foldable rear support Wheel chocks with holder Aluminium side underrun protection Rear mudflaps across the full width (not in combination with forklift holder) Half-shell fenders on 1st and 2nd axles with anti-spray mudflaps behind each axle Anti-spray mudflaps in front of and behind 3rd and 4th axles Excavator arm recess over rear axles to the rear, approx. 1,800 mm long, approx. 650 mm wide, approx. 150 mm deep 2 pairs of lashing holes (5 t each) in the excavator recess at the side of the longitudinal frame, approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable 1 storage box embedded in gooseneck floor with lid, W=720 mm / L=520 mm / D=170 mm Extendable width to 3,000 mm (not in rear bevel) (Track width of machines/vehicles to be transported must not exceed outer frame width of 2,550 mm) Storage compartment for timber planks under low-bed platform 70 mm timber for widening to 3,000 mm Low loader lashing eyes 1 pair of lashing cut-outs at the front longitudinal member in gooseneck, each rated 10 t 4 pairs of lashing holes in the outer frame, each 5 t (lashing strap attachment) 9 pairs of recessed lashing mushrooms in the outer frame, top and side, each 10 t 2 x front on gooseneck 7 x in lowered bed First lashing eye 250 mm from the front, last max. 250 mm from the rear, spacing not greater than 1,100 mm 3 pairs of additional folding lashing eyes, each 10 t: 1 x on gooseneck (protrudes) 1 x at beginning of low bed, recessed in longitudinal rails 1 x behind the last axle, recessed in the floor Trailer tow device Drawbar with certified 50 mm towing eye Drawbar height adjustable by spring Axles & suspension Drum brake axles, manufacturer's choice Axles/chassis laser aligned—reduces tire and fuel wear Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (equalisation rocking beams) Wheels and tires 235/75 R 17.5" manufacturer's choice Steel rims in twin configuration, factory silver Braking system Hnjdpfx Agorducps Isl 2-line compressed air brake system Spring-loaded parking brake 2 foolproof coupling heads at the front with connection leads to tractor unit 24 Volt ABS and ALB, with ABS connector at front, with connecting cable Note: The trailer may only be towed by tractors supporting ABS function! Electrics 12–24 volt, multi-chamber LED lamps, side yellow LED marker lights, LED license plate lights (note: some tractors may show false diagnostics despite correct function) 2 white position lights at the front, LED 2 white/red lane marker lights at the rear, LED 2 x 7-pin foolproof connectors at the front, with connecting cable 1 LED beacon with holder, switched via position light (removable beacon) 2 pairs of warning plates, double LED illuminated and extendable to 3,000mm Floor Gooseneck front with steel/checker plate covering then approx. 70 mm softwood floor, in the wheel arch area steel/checker plate covering Rear bevel with 70 mm softwood floor A

Stanje: novo, številka stroja/vozila: 408ba9a39bbb8087056d6e563, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Side underrun protection made of aluminium Full-width rear mudflap Half-shell fenders on 1st and 2nd axle with anti-spray mudflaps behind each axle; anti-spray mudflaps in front of and behind 3rd and 4th axle Excavator arm recess over the rear axles, starting to the rear, approx. 1800 mm long, approx. 650 mm wide, and approx. 150 mm deep, 2 pairs of lashing holes each rated 5 t located laterally in the excavator arm recess in the main chassis, approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 plastic toolbox with shelf, w=620/h=360/d=440 mm, lockable with a padlock (Padlock not included) 1 storage box let into the gooseneck in the floor with lid, w=720 mm/ l=520 mm / d=170 mm Extendable width to 3,000 mm (not at the rear bevel) (the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) 70 mm timber planks for widening to 3,000 mm Storage compartment for timber planks under the loading platform Lashing rings low-loader (40 lashing possibilities) 1 pair of lashing rings on gooseneck, each 5 t 9 pairs of lashing mushrooms recessed into the outer frame, top and side, each rated 10 t 2 x in the front on the gooseneck 7 x in the low-bed 6 pairs of lashing holes in the outer frame of the low-bed, each rated 5 t (for lashing strap hooks) 3 additional pairs of folding lashing rings, each rated 10 t 1 x inside beside the main frame at the beginning of the low-bed 1 x on the gooseneck (protruding) 1 x recessed into the floor behind the last axle Drawbar coupling for turntable trailer Drawbar with certified 50 mm towing eye, towing eye inclined at 8°, D-value at least 160 kN Axles & Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker equalisation) Wheels and Tyres 235 / 75 R 17.5 manufacturer’s choice Steel rims, twin mounting, factory silver Brake System 2-line compressed air brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, including connection lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connection cable Electrics 24 volt, multi-chamber lamps, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin non-interchangeable plugs at the front with connecting cable 1 LED beacon with holder, operated via parking light (beacon removable) 2 pairs of warning boards, double LED illuminated and extendable to 3,000 mm Flooring Hnedpfx Aoi Ri Dajg Ijl Gooseneck at front with steel/chequer plate floor Then with 70 mm softwood floor, in wheel arch area steel/chequer plate covering Rear bevel with 70 mm softwood floor Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber decked Hydraulically operated via tractor PTO with restrictor, control located on the left side at the front Hydraulic connection with SVK connector NW 10/3, incl. connecting hose Registration Country/Plates Registration country: Germany 24/7 Service Hotline Prepared for two-line number plate holder Contour marking with reflective strips according to ECE R 048, side white and rear red Warning plate according to ECE – 70 Paintwork Chassis hot-dip galvanized including passivation, 15-year warranty again

Stanje: rabljeno, prva registracija: 11/2006, Leto izdelave: 2006, MÜLLER - MITTELTAL T4 Kompakt Vrtljiva prikolica - Nizkopodna prikolica z zračno vzmetenimi in jamskimi kolesi - 4 x zračno vzmetene GIGANT - osi - zračno vzmetenje - 4 x kolesne jame - mehanske nakladalne rampe - 2 zadnja podporna noga, zložljiva - izvlečne opozorilne table - ABS - MICHELIN pnevmatike: 235/75 R 17.5 - težka izvedba: 40.000 kg skupne mase - lastna teža: 8.400 kg - skupna dolžina: 11.750 mm - vlečna zanka: 50 mm Posebej primerna za prevoz strojev za rezanje apna! - nemška prikolica Hnodpfxjwmpbds Ag Isl - Tehnični pregled / tehnični preizkus možen na zahtevo in za doplačilo! Pridržujemo si pravico do napak in vmesne prodaje!

Stanje: novo, največja dovoljena obremenitev: 26.100 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, Vehicle / Body: Low-bed semi-trailer First registration: New vehicle Gross weight: 35,000 kg / 47,000 kg Unladen weight: 8,900 kg Payload: 26,100 kg / 38,100 kg Overall length: 13,300 mm Loading length: 9,200 mm Width: 2,520 mm Loading height: 900 mm Further information Chassis: Low-bed semi-trailer Steel welded structure, fifth wheel plate with replaceable 2" king pin and two king pin positions (not in combination with forced steering) 24 t 2-speed landing gear, single-sided operation, with straight lower part, without thrust compensation Rear support foldable 2 wheel chocks with holders Side underrun protection, aluminium Full-width rear mudflap Mud flaps with anti-spray in front of the 1st axle and behind each axle, in accordance with EU regulations 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Extendable width to 3,000 mm (not at the rear taper) (Note: The track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Compartment for wooden planks on neck, transverse at front 70 mm wooden planks for extension to 3,000 mm Excavator arm recess over rear axles, extending to the rear, approx. 3,000 mm long, 650 mm wide, and 230 mm deep 2 pairs of lashing holes, each rated 5 t, in the excavator arm recess on side of main frame, approx. 300 mm from front and some 200 mm before rear taper Lashing points low-loader 11 pairs of lashing mushrooms, integrated top and side of the outer frame, each 10t 2x on gooseneck 9x distributed on load floor 2 pairs of lashing eyes front on gooseneck, each 5t 3 pairs of swivel lashing eyes on gooseneck, each 5t 2 pairs of folding lashing eyes additionally embedded in load floor, each 10t 1x at beginning of load floor 1x at end of rear taper 1 pair of preparation on the slope from gooseneck for 6.7t screw-on lashing eye (JDT) 8 pairs of ring lashing eyes recessed in outer frame, each 5t (convertible to stanchion pockets) 1 pair screw-on lashing eyes, each 6.7t (JDT), with large flange plate incl. thread as counternut Axles & suspension SAF or BPW drum brake axles, manufacturer's choice “Axle/chassis laser alignment” to reduce tire wear and fuel consumption Last axle is self-steering, with automatic reversing lock via reversing light and additional manual lock function via push button on vehicle Air suspension Wheels and tires 235 / 75 R 17.5" Manufacturer's choice Steel rims, twin configuration, factory silver Hjdpfx Asut Idneg Isnl Braking system 2-line compressed air brake system Coloured line routing for easy service Spring-loaded parking brake 24 Volt EBS, electronic braking system with EBS socket at front, without connecting cable Note: The trailer may only be towed by tractor units that ensure effective ABS functionality! 2 coded coupling heads at front, without connecting line With lift & lower valve Axle load detection via EBS-CAN-bus signal, for display in cab, truck must be appropriately equipped, no truck installation (not a calibrated scale) Vehicle stability control system Tire pressure monitoring system according to ECE R 141, display in tractor cab via EBS, truck installation required Electrics 24 Volt, multi-chamber lights, side yellow LED lighting Side yellow LED lighting linked to indicator "flashing side markers" 2 white position lights at front 2 white/red lane marker lights at rear 2x 7-pin coded sockets at front, without connecting cable 1 LED revolving beacon

Stanje: novo, lastna masa: 6.600 kg, največja dovoljena obremenitev: 17.400 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 6.500 mm, skupna dolžina: 10.900 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R17,5 (Doppelbereifung), barva: srebrn, vrsta prenosa: mehanski, poraba goriva (mestna vožnja): 1.090 l/100 km, Unladen weight: 6,600 kg, permissible gross weight: 24,000 kg, cargo area length: 6,500 mm. Tyre size: 235/75 R17.5. 1st axle: , 2nd axle: , 3rd axle: . Leaf suspension. 3-axle low-bed trailer with drop-bed DTS-S 300 - Turntable with robust ball bearing ring - Rear supports, foldable - 1 spare wheel carrier for 1 spare wheel, incl. wheel mounting kit - 1 spare wheel, same brand and type as main tyres, steel rim - 1 plastic toolbox - Extendable load width up to 3,000 mm (not in rear slope) - Storage compartment for timber planks in the centre of the low-bed platform - Timber planks, 70 mm, for widening to 3,000 mm Tie-down points on low-bed: - with spring-loaded lifting aid Axles + suspension: - SAF - Drum brake axles Hnjdpetcwkrofx Ag Ijl - Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalisation (rocker compensation) Braking system: - Dual-line compressed air brake system - Spring-loaded parking brake Electrics: - 24 Volt, multi-chamber lights, yellow LED side lights - 1 LED beacon with mounting bracket, controlled via parking light (removable beacon) - 2 pairs of warning boards, double LED illuminated, extendable to 3,000 mm Floor: - Storage box recessed into drive-up angle at the drop bed - Then 70 mm softwood floor, steel/chequer plate covering in wheel arch area - Rear slope with 70 mm softwood floor Ramps: Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable, covered with wood - 1 pair of ring lashing eyes recessed front in drop bed, 10 t - 4 pairs of lashing holes in rear area, 5 t each for tensioning strap hooks - 7 pairs of lashing points recessed top and side in outer frame, 10 t each (1 x front in drop bed, 6 x in low bed) - 5 pairs of stanchion pockets recessed in outer frame, inside 70 x 40 mm (convertible to 5 t ring lashing eyes for extra cost) - 2 additional pairs of folding lashing eyes, 10 t each, 1 x front in drop bed, 1 x behind 3rd axle Axles + suspension: - SAF - Drum brake axles - Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalisation

Stanje: novo, lastna masa: 6.650 kg, največja dovoljena obremenitev: 17.350 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, skupna dolžina: 10.900 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R17,5 (Doppelbereifung), barva: srebrn, vrsta prenosa: mehanski, poraba goriva (mestna vožnja): 1.090 l/100 km, Unladen weight: 6,650 kg, permissible gross weight: 24,000 kg, tyre size: 235/75 R17.5, 1st axle: , 2nd axle: , 3rd axle: , leaf suspension, - welded steel construction - bogie with heavy-duty ball bearing turntable - foldable rear support - 1 spare wheel holder for 1 spare wheel, with wheel mounting kit - without spare wheel, - 1 plastic toolbox, with shelf, dimensions 620x360x440 mm (w/h/d), lockable with padlock - extendable outriggers up to 3,000 mm (not at rear bevel) - storage compartment for timber planks underneath the low-bed area - 70 mm timber planks for extension to 3,000 mm - 1 pair of recessed lashing rings at the front in the gooseneck, each rated at 5 t - 7 pairs of lashing mushrooms recessed top and side in the outer frame, each rated at 10 t (1 x front in gooseneck, 6 x in low-bed area) - 5 pairs of stake pockets recessed in the outer frame, internal 70x40 mm - 2 additional pairs of folding lashing rings, each 10 t, 1x front in gooseneck, 1x behind 3rd axle - towing bar with 40 mm towing eye and 8° inclined towing eye - SAF drum brake axles - parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load equalisation (rocker equalisation) - 235/75 R17.5 - twin steel rims, factory silver - dual-circuit compressed air brake system - spring-loaded parking brake ABS and ALB, with socket at front, including connecting cable - 24 volt, multi-chamber lights, side yellow LED lighting - 2 x 7-pin non-interchangeable connectors at front, with connecting cable - 1 LED beacon with holder, operated via parking light (removable lamp) - 2 pairs of double LED warning panels, extendable up to 3,000 mm - gooseneck with steel/chequer plate covering - storage box recessed in the transition slope to gooseneck - followed by 70 mm softwood floor, steel/chequer plate covering in wheel well area - rear slope with 70 mm softwood floor - low-bed area incl. rear slope 6,500 mm - steel ramps 2,800 mm long, 750 mm wide, laterally adjustable, with timber covering - additional ramp safety device Hnedpfx Aeyxh Rzeg Isl

Stanje: generalkompletno obnovljen (rabljeno), Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: WFDFLT44001000966, lastna masa: 9.400 kg, največja dovoljena obremenitev: 30.600 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 10/2010, skupna dolžina: 12.120 mm, skupna širina: 27.500 mm, skupna višina: 900 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R17,5", barva: rdeča, Leto izdelave: 2010, These images are for reference only! Gross weight perm. / technical: 24,000 / 40,000 kg Payload perm. / technical approx.: 14,600 / 30,600 kg Axle load perm. / technical: 24,000 / 40,000 kg Unladen weight (base version) approx.: 9,400 kg +/- build tolerance Overall length approx.: 12,120 mm Overall width max.: 2,750 mm Neck length approx.: 2,850 mm Low loader platform length in driving lane area incl. rear bevel approx.: 7,145 mm Rear bevel length approx.: 850 mm Frame width approx.: 2,750 mm Loading height in the low bed (loaded) approx.: 900 mm Tow height approx.: 950 mm Drawbar length approx.: 1,700 mm Chassis Low Loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Side underrun protection, aluminium 1 plastic toolbox Extendable widenings to 3,250 mm (not at rear bevel) (tracking width of transported construction machines or vehicles must not exceed outer frame width of 2,750 mm) Central storage compartment for wooden planks 70 mm wooden planks for widening to 3,000 mm 2 pairs of stake pockets in the low bed, integrated in the floor longitudinal beams Lashing rings, low loader: 2 pairs of lashing rings on the neck, each 5 t 1 pair of lashing rings in the rear bevel 4 recessed lashing rings, placed centrally in the floor 2 pairs of key slot profiles in the driving lane, for longitudinal guide rails and as additional lashing points 6 pairs of lashing mushroom anchors in the low bed outer frame, each 10 t 5 pairs of stake pockets in the outer frame of the low bed 4 additional pairs of 10 t lashing rings: 1 on the neck 3 recessed in the floor of the low bed Drawbar coupling, turntable trailer: Drawbar with tested 50 mm towing eye Axles + suspension: Drum brake axles Parabolic spring suspension with maintenance-free steel-rubber bearings and mechanical axle load equalization front and rear (rocker leveling) Wheels and tires: 235 / 75 R 17.5" Steel rims, twin arrangement, factory silver Brake system: 2-line air brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front with connection lines for towing vehicle ABS and ALB, with ABS connector at front, with connection cable Attention: The towed trailer may only be pulled by towing vehicles that ensure proper function of the ABS! Floor: Neck area with steel/chequer plate flooring then 70 mm softwood floor, wheel recesses with steel/chequer plate flooring Rear bevel with 70 mm softwood floor Access ramps: Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber surface Hydraulically operated via tractor PTO Operating instructions: For 10,000 kg axle load, a special permit is required, only indivisible loads permitted!!! Hedpfx Asyxq A Hjg Ienl Note! Overlength and excess width, special permanent approval required. For applications for special permits for heavy-duty transport, an axle load display is required for air-suspended vehicles! This applies to all deviations from § 34 StVZO (axle load and permissible gross weight exceedance) that require a special permit under § 70 StVZO. The declared gross weight is technically feasible; depending on the load, the gross vehicle weight may not be achievable while observing permissible axle, support, and saddle loads. (Poor driving and trailing behavior possible due to incorrect load distribution) These images are for reference only!

Stanje: novo, lastna masa: 6.600 kg, največja dovoljena obremenitev: 17.400 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, skupna dolžina: 10.900 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R17,5 (Doppelbereifung), barva: srebrn, vrsta prenosa: mehanski, poraba goriva (mestna vožnja): 1.090 l/100 km, Unladen weight: 6,600 kg, permissible gross weight: 24,000 kg, tyre size: 235/75 R17.5, 1st axle: , 2nd axle: , 3rd axle: , leaf suspension, weights: Immediate approval technically possible Gross weight: 24,000 kg, 30,000 kg, payload approx.: 17,400 kg, 23,400 kg; unladen weight approx.: 6,600 kg +/- manufacturing tolerance. Dimensions (approx.): Total length 10,900 mm, total width 2,550 mm, gooseneck length 2,180 mm, low bed platform length incl. rear chamfer 6,500 mm, rear chamfer length 950 mm, frame width 2,520 mm, loaded loading height in low bed 860 mm, coupling height 900 mm, drawbar length 1,900 mm. Equipment: - Extendable width up to 3,000 mm (not in rear chamfer), incl. timber planks - SAF drum brake axles - Parabolic suspension - Drawbar with certified 40 mm towing eye - Tyres 235/75 R17.5 - Storage box recessed at the transition to the gooseneck - 1 plastic toolbox with shelf, 620 mm wide / 360 mm high / 440 mm deep - Steel ramps: 2,800 mm long, 750 mm wide, laterally adjustable, timber-coated - Ramps with spring assist - Frame hot-dip galvanised Subject to errors and changes. Hnjdpfsx Nrp Nox Ag Isl

Stanje: novo, številka stroja/vozila: 195f80ad09517628522e33a91, lastna masa: 7.300 kg, največja dovoljena obremenitev: 16.700 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low Loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Aluminum side underrun protection Rear mudflaps across the entire width Quarter shell fenders in front of 1st axle 1st pair of wheel recesses embedded after the kink in the loading bed area, ramped entry, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! The frame in the main beam area is 400 mm higher than the wheel recess. 2nd pair of wheel recesses embedded between the axles in the loading bed area, ramped entry, length at the bottom approx. 600 mm, approx. 300 mm deep. Note! The frame in the main beam area is 300 mm higher than the wheel recess. Sliding extensions for widening, extendable to 3,000 mm (not in tail ramp area) (The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) Sliding extensions for widening, extendable to 3,000 mm, also at the bottom in the wheel recesses, foldable at the wheel recess extensions (extension not in the tail ramp area) (The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) 70 mm timber planks for extension to 3,000 mm Tie-down points on low loader 1 pair of lashing cutouts embedded in the longitudinal beam at the front in the kink, each rated at 10 t 4 pairs of lashing holes in the outer frame, each rated at 5 t (for attaching tie-down straps) 7 pairs of lashing mushrooms recessed at the top and side in the outer frame, each rated at 10 t 1x at the front in the kink 6x in the loading bed Hodpfxsi Ri Rvs Ag Ionl First lashing point 250 mm from the front and last max. 250 mm from the rear, spacing between lashing points no greater than 1,100 mm Drawbar for turntable trailer Drawbar with certified 40 mm towing eye Axles & suspension SAF drum brake axles Laser axle/chassis alignment – reduces tire wear and fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bushings Wheels and tires 235 / 75 R 17.5 Manufacturer's choice Steel rims in twin arrangement, factory silver Braking system 2-line compressed air braking system Spring-applied parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, with connection cable. Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber lights, LED side marker lights, 2 white position lights at the front 2 white/red lane guidance lights at the rear 2 x 7-pin fail-safe connectors at the front, with connection cable, 1 LED rotating beacon with holder, switched via side light (removable beacon) 2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm Floor Front kink with steel/checkered plate covering Storage box embedded in the ramp to the kink, then with 70 mm softwood floor, in the wheel arch area with steel/checkered plate covering Tail ramp with 70 mm softwood floor Low loading area including tail ramp: 6,500 mm Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered With spring assist Operating Instructions For 10,000 kg axle load an exemption is required, only indivisible loads allowed! The stated gross weight is technically possible, but depending on the type of load, the gross weight may not be achievable within the pe

Stanje: novo, številka stroja/vozila: ee3256d63dd23b3ad1bdf9ab0, lastna masa: 10.280 kg, največja dovoljena obremenitev: 13.720 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with robust ball bearing slewing ring Foldable rear support legs 2 wheel chocks with holders Aluminum side underrun protection Full-width rear mud flaps Quarter shell fenders in front of the 1st axle Excavator arm trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes rated at 5 t each in the excavator arm trough, positioned laterally on the longitudinal frame approx. 300 mm from the front and approx. 200 mm before the rear taper 1 storage box recessed into the gooseneck on the floor with lid, W=720 mm/ L=520 mm / D=170 mm 1st pair of wheel recesses after the gooseneck, recessed in the low-bed deck area, sloped for entry, length at bottom approx. 1600 mm, approx. 400 mm deep. Note! Main frame section 400 mm higher than wheel recess. 2nd pair of wheel recesses between the axles, recessed in the low-bed deck area, sloped for entry, length at bottom approx. 600 mm, approx. 300 mm deep. Note! Main frame section 300 mm higher than wheel recess. Removable wheel recess covers from the main frame, with wooden inserts. Distance from main frame longitudinal member to outside member approx. 1280 mm (wheel recess area) Extensions extendable to 3,000 mm, foldable at the wheel recess extensions (extensions not in the rear taper nor at the bottom of the wheel recesses) (The track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for timber planks centrally on load area or underneath depending on technical feasibility 70 mm timber planks for extension to 3,000 mm Hnedpfx Agei Ri I Ns Iol Low-bed lashing points 1 pair of ring lashing points recessed in the gooseneck, each rated at 5 t 8 pairs of lashing mushrooms recessed in the top and side outer frame, each rated at 10 t 2 x at the front on the gooseneck 6 x in the low-bed – first lashing point 250 mm from the front, last maximum 250 mm from the rear, distance between lashing points not greater than 1100 mm 5 pairs of ring lashing points recessed in the outer frame, each rated at 5 t (can be converted to stake pockets) Drawbar Assembly for Turntable Trailer Drawbar with tested 50 mm towing eye, towing eye inclined at 8° Axles + Suspension SAF drum brake axles Axles/chassis laser-measured to reduce tire wear and fuel consumption Air suspension with lift & lower valve, separately operable at front and rear Wheels and Tires 235 / 75 R 17.5 Manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line pneumatic braking system Spring-loaded parking brake Trailer info center, displays vehicle data (e.g., axle load—not a calibrated scale) and odometer Axle load detection via EBS-Canbus signal, for display in the cab (truck must be pre-equipped, not installed in truck, not a calibrated scale) Vehicle Stability System Duomatic coupling at the front with connecting line to the truck tractor EBS, electronic braking system with EBS socket at the front, with connecting cable Note: The trailer may only be towed by vehicles that ensure proper ABS function! Electrics 24 volts, multi-chamber LED lights with resistor, side marker yellow LED lights, LED license plate lights (Note: Certain towing vehicles may show diagnostic errors despite systems working correctly) 2 white front position lights in LED 2 white/red lane marker lights at the rear in LED Additional LED w

Stanje: novo, številka stroja/vozila: 55d3c5c03e032385649769b1b, lastna masa: 9.900 kg, največja dovoljena obremenitev: 14.100 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-Loader Trailer Steel welded construction Turntable with heavy-duty slewing ring, integrated storage box incl. Turntable front structure Foldable rear support 2 wheel chocks with holders Aluminum side underrun protection Full-width rear mud flaps Extendable widenings to 3,000 mm (not at rear taper) (track width of the machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Central compartment on loading area for timber planks 70 mm timber planks for widening to 3,000 mm Lashing points Low-loader 3 pairs of integrated lashing points, each rated to 10 t, at the front floor 6 pairs of mushroom lashing points, top and side integrated in outer frame, each 10 t 1 x at neck area Hnjdpsi Ri I Eefx Ag Iel remaining points distributed, distance no greater than 1,200 mm 1 x at rear taper 5 pairs of stake pockets integrated in the outer frame, internal size 70 x 40 mm (convertible to 5 t ring lashing eyes, not included) Drawbar assembly for trailer turntable Drawbar with certified 40 mm towing eye Note: For 40 mm towing eye, the maximum permissible gross weight of the towing vehicle is 18,000 kg. Otherwise, a 50 mm towing eye is required. Axles + Suspension SAF drum brake axles Laser-aligned axles/chassis to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization front and rear (rocker compensation) Wheels and Tires 235 / 75 R 17.5 manufacturer's choice Steel twin wheels, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connection lines to the truck ABS and ALB, with ABS connector at front, connection cable included Attention: The trailer may only be towed by vehicles that ensure ABS functionality! Electrics 24-volt multi-chamber lights, side yellow LED lighting 2 white front position lights 2 white/red rear lane marker lights 2 x 7-pin non-interchangeable connectors at the front, with connection cable 1 LED beacon with bracket, operated via parking lights (removable beacon) 2 pairs of warning boards, double LED-lit and extendable to 3,000 mm Floor Steel floor at front section thereafter 70 mm softwood floor, in wheel arch area with steel/chequer plate covering Rear taper with 70 mm softwood floor Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable wooden inlays spring-assisted lifting Operating instructions Exception permit required for 10,000 kg axle load, only indivisible loads allowed!!! The specified total weight is technically possible. Depending on the cargo, the full gross weight may not be achieved while observing permissible axle/pin/support loads (poor tracking and handling may result from incorrect load distribution) Country of Registration / Plates Registration country: Germany 1 with Dekra inspection and report (according to §13 EC-FGV) 24/7 service hotline prepared for 2-line license plate holder Conspicuity markings with reflective strips acc. ECE R 048, white on the sides, red at the rear Paint Frame RAL 3002 Carmine Red 10 years warranty against rust-through Drawbar galvanized or black, at manufacturer's discretion Loading ramps hot-dip galvanized Attention: Archive photos!

Stanje: novo, številka stroja/vozila: f79a9f15e7131d57a512793ab, lastna masa: 8.900 kg, največja dovoljena obremenitev: 15.100 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball race Foldable rear supports 2 wheel chocks with holders Side underrun protection, aluminium Rear spray guards across the full width Quarter fender before 1st axle Extendable outriggers up to 3,000 mm (not in the rear slope area) (Note: The track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Central storage compartment for timber planks on the loading area 70 mm timber planks for extension to 3,000 mm Lashing points Low-bed 1 pair of lashing rings on gooseneck, each rated at 5 t 9 pairs of lashing mushrooms, flush-mounted on the top and side in the outer frame, each rated at 10 t 2 x front on gooseneck 7 x in the low-bed 6 pairs of lashing holes in the outer frame of the low-bed, each rated at 5 t (for attaching tie-down straps) Drawbar System Turntable trailer Drawbar with certified 50 mm towing eye Axles & Suspension SAF drum brake axles Laser-aligned axles/chassis to reduce tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber mount and mechanical axle load compensation (rocker balance) front and rear Wheels and Tyres 235/75 R 17.5 Manufacturer's choice Steel rims, twin arrangement, factory silver Brake System 2-line air brake system Spring-loaded parking brake 2 swap-proof coupling heads at the front with connection lines to towing vehicle ABS and ALS, with ABS connector at the front and connection cable Attention: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber lights, side amber LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 1 LED beacon with holder, switchable by parking light (removable) 2 pairs of warning boards, double LED illuminated and extendable up to 3,000 mm 2 x 7-pin swap-proof plugs at the front, with connecting cable Floor Gooseneck at front with steel/chequer plate covering Thereafter 70 mm softwood floor, wheel arch area with steel/chequer plate covering Rear slope with 70 mm softwood floor Access Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood plated Hydraulic activation via auxiliary drive on tractor unit with throttle, operation on front left side Hydraulic connection with SVK connector NW 10/3, including connection hose Operating Instructions A special permit is required for an axle load of 10,000 kg; only indivisible loads possible!!! The specified gross weight is technically possible; depending on the freight, the permissible gross weight may not be achieved while respecting axle, support and kingpin loads. (Poor driving and trailing behaviour possible due to incorrect load distribution) Registration Country / Plates Country of registration: Germany With Dekra inspection and report (according to §13 EC-FGV) 24/7 Service Hotline Included Prepared for double-line number plate holder Contour marking with reflective strips according to ECE R 048, white on sides, red at rear Paintwork Frame DB 7350 Nova Grey Hodpfei Ri Izjx Ag Ijnl 10-year warranty against rust-through Drawbar galvanised or black, at manufacturer’s choice Access ramps hot-dip galvanised

Stanje: novo, številka stroja/vozila: dc46d2e1cd272305b99fb3160, lastna masa: 9.800 kg, največja dovoljena obremenitev: 31.200 kg, skupna masa: 41.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Vehicle consisting of: Chassis low-bed semi-trailer Steel welded construction, kingpin plate with replaceable double kingpin and two kingpin positions 24-ton, 2-speed landing gear, single-sided operation, straight lower section, without thrust compensation Foldable rear support 2 wheel chocks with holders Side underrun protection, aluminum Quarter mudguards in front of and behind the axle assembly 1st pair of wheel recesses embedded in the low-bed drive lane area after the gooseneck, tapered for entry. Lower length approx. 1,600 mm, recess depth approx. 260 mm. Note! Frame in the main beam area is 260 mm higher than the wheel recess. 2nd pair of wheel recesses between axles A and B. Lower length approx. 350 mm, depth approx. 260 mm. Note! Frame in the main beam area is 260 mm higher than the wheel recess. If wheel loaders are to be transported and the total height needs to be checked, please provide technical data sheets of the wheel loader types with exact information (if total height is exceeded -> customer responsibility, approval required), (depending on ground clearance under the machines, inserts in the wheel recesses may be required by the customer) Wheel recess covers extendable from the main frame, with wooden inserts. Extensions extendable to 3,000 mm (not in the rear bevel and not in the lower wheel recesses). (The track width of construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm.) Storage compartment for wooden planks on the gooseneck, crosswise at the front 70 mm planks for extension to 3,000 mm Lashing eyes low-bed trailer 2 pairs of ring lashing eyes, each 5t at the front on the gooseneck 11 pairs of lashing mushrooms recessed at the top and side in the external frame, each 10t 2x on gooseneck, 9x distributed on low-bed platform; first lashing point 250 mm from the front and last at max. 250 mm from the rear, distance between lashing points no greater than 1,100 mm 8 pairs of stake pockets recessed in the external frame, internal dimensions 70 x 40 mm, or instead of stake pockets, 5t ring lashing eyes recessed in the floor Axles & Suspension SAF drum brake axles Axles/chassis laser-measured to reduce tire wear and fuel consumption Air suspension Wheels and tires 235 / 75 R 17.5 as per manufacturer's choice Steel rims in twin arrangement, factory silver Brake system 2-line compressed air braking system Spring-loaded parking brake EBS, electronic braking system with EBS socket at the front, without connection cable Attention: The trailer may only be towed by tractors that ensure the effectiveness of ABS! 2 non-interchangeable coupling heads at the front, without connecting line with lift & lower valve Axle load detection via EBS CAN bus signal, for display in the driver's cab (truck must be pre-equipped accordingly, not installed on truck; not a calibrated scale) Vehicle stability control system Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front Hnjdpfxji Ri Hce Ag Iol 2 white/red lane mark lights at the rear 2 x 7-pin, non-interchangeable sockets at the front, without connection cable 1 x LED beacon with holder, switched via parking light (lamp removable) 2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm, removable with plug Floor Gooseneck with steel/chequer plate covering Storage box embedded in the sloped transition to gooseneck Then with 70 mm softwood floor; in the lower wheel recesses and w

Stanje: novo, številka stroja/vozila: 3c70e9a5d82cfb3ada79baf95, lastna masa: 8 kg, največja dovoljena obremenitev: 17 kg, skupna masa: 26 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 205 / 65 r 17,5, Further Information Chassis: Semitrailer Logistics Fine-grained steel welded construction, fifth wheel plate with interchangeable 2-inch kingpin, rear bevel approx. 1920 mm, continuous ramp hanging bar at the rear and at the front of the gooseneck, ground rollers at the rear, lowered deck (deep bed) after the step-down up to the axle assembly. Drawing release from the customer required upon order! Pair of lashing mushroom pins recessed on top and side in the outer frame, each rated for 10t Pair of lashing eyes recessed in the outer frame on the gooseneck, each rated for 5t 24t two-speed landing gear, single-sided operation, with straight lower part, without compensating plate Foldable rear support, mounted externally Wheel chocks with holder Side underrun protection – aluminum Rear underrun protection – steel, for EU, where technically possible Quarter-shell mudguards With anti-spray mudflaps according to EU regulations 1 pair of wheel recesses recessed after the gooseneck in the deep-bed lane area, sloped for easier entry. Bottom length approx. 1840 mm, recess depth approx. 200 mm. Second pair of wheel recesses at rear bevel. Depth approx. 200 mm. Note! Frame in the main beam area is 200 mm higher than the wheel recess. Detailed technical inspection required upon order. Removable wheel recess covers from the deep bed with hardwood inlays, at rear bevel with hardwood inlays. Electric cable winch, 24 volts, pulling force 5500 kg, mounted in the gooseneck step-down, does not reach into load area, operated by remote control, cable length 35 m × approx. 10 mm, with roller fairlead and detachable guide roller at the rear bevel. Axles & Suspension SAF or BPW drum brake axles at our discretion Air suspension with raise & lower valve + auto-reset function Wheels and Tires 205/65 R 17.5 tires with 129/127K (132/132G) rating for 8t tire load capacity at max. 90 km/h, preference of manufacturer Steel twin wheels, factory silver Brake System 2-line compressed air brake system Spring-actuated parking brake 2 interchangeable coupling heads at front, without connecting line EBS by Haldex, electronic braking system with EBS socket at front, without connecting cable (brake calculation sent to customer for approval, 15.07.2021) Hnsdpfji Ri Hrsx Ag Isl Attention: The trailer may only be towed by tractor units that ensure ABS effectiveness! Axle load detection via EBS CAN bus signal, display in the driver’s cab possible (truck must be properly prepared, not installed, not a calibrated scale) Electrics 24 volts multi-chamber rear lights, lateral yellow LED lights 2 white position lights at front 2 white/red outline marker lights at rear 2 × 7-pin and 1 × 15-pin interchangeable sockets at front, without connecting cable Floor Gooseneck with steel/checker plate covering 30 mm phenolic resin plywood floor, in deep bed between main rails In the drive lane area with serrated grating, in wheel recesses with steel/checker plate covering Ramps Pair of aluminum ramps, 3,200 mm long, load capacity 12,000 kg per pair Pair of steel ramps for entry into deep bed Pair of steel ramps for crossing gooseneck Sidewalls Approval / Signage Registration country: Germany With DEKRA inspection and certificate (according to §13 EC-FGV) Prepared for single-line license plate holder Contour marking with reflective strips as per ECE R 048, yellow at sides and red at rear Warning plate as per ECE-70 Paintwork Frame painted RAL 9018 Papyrus White Support feet coated black Attention: Archive ima

Stanje: rabljeno, največja dovoljena obremenitev: 38.230 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2026, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Müller-Mitteltal Low Loader with Wheel Recesses TS 3 RM ML 30.0, 2 Loading Heights and Ramps Hjdpfxoy R Ipue Ag Ijnl * Saddle load increase from 12 t to 18 t included, king pin installed in the second king pin position 2", up to the gooseneck 2,750 mm. Rear swing radius approx. 2,400 mm in the clear (a minimum clearance of 150 mm is recommended). Front swing radius 1,480 mm or 1,570 mm with spare wheel. Note: Sufficient clearance to the towing vehicle must be ensured by the customer. * Sliding elements for wheel recesses at the front and rear (205 mm deep). 6 loose planks for wheel recess supports as receiving pockets according to Code 09.112. ALU compressed air tank instead of steel. * Smartboard control unit installed on the trailer as an info tool with pressure sensors, providing total axle load display. Display optional via the control box or in the truck via the EBS air suspension system (depends on truck manufacturer). * SP combination package: Toolbox with 45° corners made of galvanized steel, additionally powder-coated in RAL 9006 White Aluminium, mounted on the saddle platform W=2,480 x H=500 mm with top folding lid, side doors, and angled left ALU side walls foldable to the saddle platform (500 mm high), ALU rear wall plug-in (150 mm high), ALU sideboards inside and outside painted in RAL 9006 White Aluminium. Includes foldable and removable rear stanchions, galvanized (without finish coating). Includes bolted front structure. Length from front cross member to gooseneck 3,935 mm, front swing radius without spare wheel at gooseneck dimensions 2,450 mm or 2,750 mm approx. 1,750 or approx. 1,480 mm. * 2 recessed container locks installed in the front cross member. * 3 receiving pockets under the saddle platform for optional storage of ALU loading ramps or wooden planks for wheel recess covers. * Folding outriggers/telescopic outriggers (galvanized) and wooden planks for widening incl. (not on rear slope), plank holder on the saddle platform (load track width may not exceed 2,500 mm). * Second LED position light at the warning package front and rear (dual lighting), only in combination with warning package. * 2 LED reversing lights at the rear of the trailer, switched with reverse gear (suitable for 12 V and 24 V), max. total 2 additional allowed. * 7-pin socket at the rear, wired for overlength lighting with taillight (58 R) and earth. * Rubber coating on the drive-up slope left and right (approx. 860 mm long) 190 07644 rubber strips on the inner plank of the one-piece ramps. * Fully automatic central lubrication system with pump (24V), grease reservoir, and integrated trailer control unit, without connection of the ramps (when with steering: incl. connection of the distributor on the saddle platform). Note: Only possible with towing vehicles with a 24V lighting system! Subject to prior sale and errors! Sale exclusively subject to our terms and conditions. Important Notice: Despite careful verification of all details in our offer, errors can occur. Some may be caused by transmission errors in the systems of various platform providers. Therefore, we would like to point out that all information is provided without guarantee and does not constitute legal entitlement. Legal: This sales advertisement does not constitute an offer within the meaning of §145 BGB. Rather, it provides information for contract negotiations. All information given here is without guarantee and therefore does not constitute any assured property.

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Rear axle steered with electro-pneumatic steering lock ----Suspension: * Air suspension with lift and lowering system, including RtR valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control box mounted on trailer as info tool with pressure sensors for total axle load display * 15-pin electrical connector * LED lighting system 12/24V * Removable LED beacon, rear left ----General Attachments: * Side underrun protection * Support legs at the front and mechanical swivel supports at the rear of the chassis * Straight pressed steel fenders * Spare wheel holder under the chassis, right side ----Low Loader Deck: * Fifth wheel platform with 45° chamfered front corners and front toolbox made of galvanized steel sheet, W = 2,480 x H = 500 x L = 665 mm, with folding lid * 400 mm aluminium side boards (RAL 9010 pure white) on the fifth wheel platform, foldable and removable * Rear board plug-in, 150 mm high * Rear slope on fifth wheel platform to low-bed approx. 700 mm long * Fifth wheel platform with 50 mm timber planks, low-bed deck with 60 mm timber planks * Tread plate above the axles ----Widenings: * 8 x mechanical folding extensions to a total width of 3 meters (not on rear slope; extension planks available with storage on the platform) * Mechanically adjustable warning panel sets front and rear ----Load Securing (Lashing Package): * On the fifth wheel platform: 2 x 6.3 t lashing rings on each side, plus 3 x 5 t lashing bars per side in the outer frame * On the low-bed platform: 2 x 13.4 t lashing rings per side, plus 4 x 10 t lashing rings, pivotable and lowerable, recessed in the outer frame * 2 x 6.4 t lashing eyes per side, plus 1 lashing ring at the excavator arm rest * 2 x container locks directly after the neck in the low-bed platform ----Excavator Arm Rest: * Continuous excavator arm rest from end of last fixed axle over steering axle to end crossbeam, with internal reinforcements, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Ramps: * Mechanical one-piece hot-dip galvanized hydraulic ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way control block for later customer-side retrofitting of hydraulic ramp shifting * Outer board on ramp made from 50 mm hardwood * Climbing strips on outer frame of ramp and on approach slope * Rubber matting on ramp and approach slope ----Hydraulics: * Hydraulic flow divider in trailer (for hydraulic pump performance in the truck between 40 l/min and 120 l/min) ----Loading Dimensions: * Fifth wheel platform loading area: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Unladen loading height: approx. 910 mm (incl. 860 mm approach slope) ----Fifth Wheel Height: * approx. 1,220 mm (suitable for 2- and 3-axle tractor units) ----Coating: * Chassis, ramps, rear folding supports, extension consoles hot-dip galvanized * Axles, support legs, air tanks painted in a black shade * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Sample images may show equipment not included with the offered vehicle ----Delivery time: * available from c Hsdpfey Ngzyox Ag Ienl

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: Hnjdpfoy Ngz Hsx Ag Isl * 3 x 11 t BPW Eco Plus axles * Last axle trailing steered with electro-pneumatic steering lock ----Suspension: * Air suspension with lift-and-lower function and RtR valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control box mounted on the trailer as an infotool with pressure sensors for total axle load display * 15-pin power connector * LED lighting system 12 / 24V * Removable LED beacon, rear left ----General Attachments: * Side underrun protection * Landing gears at the front as well as mechanical swing-down supports at the rear of the chassis * Straight sheet steel mudguards * Spare wheel holder under the chassis on the right side ----Low Loader Deck: * Gooseneck platform with 45° chamfered front corners and front toolbox made of galvanized sheet steel W = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm aluminium side boards (RAL 9010 pure white) on the gooseneck, foldable and removable * Rear wall – 150 mm – fitted * Rear slope at the gooseneck platform to the low-bed approx. 700 mm long * Gooseneck platform with 50 mm timber planks, low-bed platform with 60 mm timber planks * Tread plate over the axles ----Extensions: * 8 x mechanical fold-out extensions to 3 m total width, but not on the rear slope (extension planks present with storage on gooseneck platform) * Mechanically adjustable warning sign packages front and rear ----Load Securing (Lashing Package): * On the gooseneck platform: 2 x 6.3 t lashing rings each side and 3 x 5 t lashing bars per side in the outer frame * On the low-bed platform sides: 2 x 13.4 t lashing rings each, and 4 x 10 t swivel and lowerable lashing rings recessed in the outer frame * 2 x 6.4 t lashing eyes per side and rear 1 lashing ring in the excavator arm recess * 2 x container locks directly after the gooseneck in the low-bed platform ----Excavator Arm Recess: * Excavator arm recess from end of last rigid axle, over steering axle to end crossmember, continuous, with internal reinforcement profile, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Loading Ramps: * Mechanically one-piece hot-dip galvanized hydraulic loading ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way control block for later customer retrofit of hydraulic ramp shifting * The outer board of the ramp consists of 50 mm hardwood * Climbing strips on the outer frame of the ramp as well as on the drive-up slope * Rubber on the ramp and drive-up slope ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump capacity in the truck from 40 up to 120 l/min) ----Loading Dimensions: * Loading area, gooseneck platform: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Loading height unladen approx. 910 mm (incl. 860 mm drive-up slope) ----Fifth Wheel Height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractor units) ----Paintwork: * Chassis, loading ramps, rear folding supports, extension brackets hot-dip galvanized * Axles, landing gears, air reservoirs painted in a black tone * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Sample images may include features not part of the offered vehicle * Sample images ----Delivery time: * tba

Stanje: rabljeno, največja dovoljena obremenitev: 36.540 kg, skupna masa: 48.500 kg, konfiguracija osi: 3 osi, prva registracija: 06/2020, naslednji pregled (TÜV): 05/2028, Leto izdelave: 2020, Oprema: ABS, Internal vehicle number: G400133 Currently en route to our yard in Kaufungen - Kassel, Germany. Immediately available. For more information, contact Luis Lucena. LANGENDORF Low Loader SATÜ 30 – 10.0 m With wheel wells Year of manufacture: 2020 Radio remote control 3 axles – 2 steered – 1 liftable Length: 13,900 mm Loading area: 10,000 mm Technically permitted gross weight: 48,500 kg Unladen weight: 11,960 kg Financing example: * Internal number: G400133 * Purchase price: €69,900.00 * Down payment: 10% Hnodpjy A Uxaofx Ag Isl * Term: 60 months * Monthly installment: €1,050.02 * Final residual value: €13,380.00 If you are interested in this offer or wish to modify it to suit your needs, please contact Mr. Enchev. We look forward to your call. Errors excepted. We are happy to accept your used vehicle as a trade-in. Financing available directly through us. GOLEC NUTZFAHRZEUGE GMBH We speak: German, English, Spanish, Polish, Ukrainian, Russian, Bulgarian.

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 04/2005, barva: črn, Leto izdelave: 2005, Oprema: ABS, = Additional Options and Accessories = - Spare wheel - Twin tires = Notes = Hjdpfx Agexw T Uae Ijnl Müller Mitteltal 2-axle T5 2AL low loader with ramps Air suspension BPW axles ABS ZSA Tires 60% tread, GR 235R17.5 ID No.: 665 We look forward to welcoming you for consultation, contract signing or vehicle collection at our dealership. Please arrange an appointment in advance. If you are unable to visit us in person, we offer complete processing via phone/email/WhatsApp/fax. On request, we deliver your new vehicle directly to your door. This means you get the best price, maximum security, and convenience when buying your vehicle. Trade-in We are happy to take your used vehicle in part exchange. We offer the possibility of digital vehicle valuation based on your photos, even without visiting our dealership. Our specialized purchasing team offers you a guaranteed top price. On request, we will deliver your new pre-owned vehicle nationwide right to your doorstep and take your old vehicle back with us. Financing – Leasing Immediate approval and settlement of existing loans. Your specialist partner for cars, vans, commercial vehicles, and construction machinery. ITC GmbH & Co KG Siemensstraße 7 32312 Lübbecke (industrial area) Visit us on our website Always over 400 vehicles in stock The information provided in advertisements, online, price tags, and images are non-binding descriptions and do not constitute guaranteed characteristics. The seller assumes no liability/warranty for typing and data transmission errors. Listed equipment may require separate verification; the offer is generally without new TÜV inspection, but we would be pleased to make you an offer through our partner workshop. Subject to errors and prior sale. = Additional Information = Unladen weight: 8,900 kg Payload: 26,100 kg Gross vehicle weight: 35,000 kg Sales price: €18,000, US$21,210

Stanje: kot nova (razstavni stroj), lastna masa: 10.000 kg, največja dovoljena obremenitev: 30.000 kg, skupna masa: 40.000 kg, konfiguracija osi: 4x2, dolžina tovornega prostora: 9.220 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17,5, Leto izdelave: 2025, Oprema: ABS, osrednja vrtljiva plošča, spojka prikolice, HTD 40K-RM-BM_ Internal dimensions: approx. 9,220 mm x 2,540 mm Overall dimensions: approx. 11,300 mm x 2,540 mm x 3,850 mm Permissible total weight: 24,000 kg Payload: approx. 14,000 kg Tyres: 235/75R17.5 inches Loading height: approx. 900 mm Drawbar length: approx. 1,500 mm Coupling height: approx. 820-1,000 mm Ramp angle: approx. 10° Ramp length: approx. 3,150 mm Ramp width: approx. 750 mm Permissible total weight special approval: 40,000 kg Payload special approval: approx. 30,000 kg Low bed length: approx. 6,610 mm Overall dimensions (LxWxH): 11,200 Technical overall weight: approx. 44,000 kg Technical axle load: approx. 11,000 kg 6 pairs of lashing points, 3,000 kg per lashing point Lashing points in the outer frame of the low bed 4 pairs of lashing points, 3,000 kg per lashing point Lashing/stake pockets 3 t in the outer frame of the high bed 1 pair of lashing points, 3,000 kg per lashing point Lashing/stake pockets 3 t in the outer frame of the low bed Suspension Air suspension unit including raising and lowering effective on the rear axle unit Braking system Braking system according to EC directives with EBS 4S/3M in multivoltage version (12-24V), spring-loaded parking brake incl. 2 external test connections for brakes/modulator and bellows pressure Electrics LED lighting with indicator function for side marker lights, multivoltage (12-24V) Turntable Robust welded construction with low-maintenance ball race turntable Towing device Cranked drawbar with towing eye Ø 50mm, low-maintenance silent bushings including height adjustment for drawbar Frame Robust welded construction made of high-strength fine-grained steel Continuous cross members for maximum stability Wheel recesses at the front (top length approx. 2,500 mm - depth approx. 410 mm) and at the rear (top length approx. 1,470 mm - depth approx. 370 mm); without wheel recess covers; Excavator trough (length 1,650 mm, width 750 mm, depth 190 mm) Wheel cut-outs above the rear wheels with wheelbase 2,010 mm, front corners chamfered, rear climbing bars on the incline for maximum safety during loading and unloading 4 pairs of stake pockets (90x50 mm) in the outer frame high bed 1 pair of stake pockets (90x50 mm) in the outer frame low bed Floor 50 mm softwood planking (painted/impregnated) Ramps One-piece hot-dip galvanised loading ramps (3,150 mm x 750 mm) with 50 mm softwood planking (painted/impregnated), laterally adjustable, directly acting upright spring lifters for effortless operation Finishing Chassis frame hot-dip galvanised in immersion bath Support 2 folding supports at the rear left and right at the vehicle rear Equipment Folding side underrun protection, front semicircular plastic mudguards – rear straight steel mudguards with antispray, 2 wheel chocks with holders; contour markings in accordance with ECE Directive R48 Front wheel recess cover with 3 pairs of stake pockets, without planking (cover retractable under the longitudinal beams) 975.00888 Hardwood planking for front wheel recess cover Rear wheel recess cover with 1 pair of stake pockets, without planking (cover retractable under the longitudinal beams) 975.00897 Hardwood planking for rear wheel recess cover 3 pairs of screwed lashing rings 6 t 3 m equipment package without incline B=11,200 Folding extension with softwood boards 970.04199-36 LED warning package HTD cranked Aspöck warning boards 4-fold, electrics and revolving beacon Hjdpoiciutefx Ag Ionl 1 pair of storage compartments for wooden boards 3 m package (2 pieces moun

Stanje: novo, največja dovoljena obremenitev: 26.500 kg, skupna masa: 36.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.450 mm, širina tovornega prostora: 2.550 mm, skupna širina: 2.550 mm, Leto izdelave: 2026, Oprema: ABS, WIESE 3-axle low-loader with ramps and wheel recesses ? NEW Availability approx. 4 months from order ---- Vehicle data Manufacturer: WIESE * Type: WSA 3-36 TL * Year of manufacture: 2025 * Axles: 3 * Gross weight: 39,000 kg * Fifth-wheel load: 12,000 kg * Aggregate axle load: 27,000 kg * Unladen weight: approx. 9,500 kg * Tyres: 235/70 R17.5 * Brakes: WABCO EBS with RSS ---- Dimensions * Load bed length: 13,450 mm * Low-bed length: approx. 9,550 mm * Fifth-wheel section: approx. 3,640 mm * External width: 2,550 mm * Bed height low-bed: approx. 920 mm * Fifth-wheel height: approx. 1,250 mm ---- Equipment * 3 x SAF axles (9 t) with air suspension * 1st axle with lift function * 3rd axle with trailing steering axle (lockable) * Electronic air suspension E-TASC * WABCO EBS brake system with Roll Stability Support * Tyre pressure monitoring system for 12 tyres * Full LED lighting * 4 x LED work lights * 15-pin + 2 x 7-pin sockets ---- Bodywork * Sturdy steel frame * 28 mm hardwood floor / Omega floor * 13 pairs of lashing rings 8,000 kg * Additional lashing points 5,000 daN * 2 pairs of wheel recesses * Digger arm recess * Aluminium plug-in side boards on the raised deck * Toolbox at the front ---- Ramps Hnedjyuq Igepfx Ag Ijl * 2 x aluminium drive-on ramps * Dimensions: approx. 2,800 x 600 mm * Load capacity: 27,460 kg * Spring lifting system * Sideways adjustable ---- Miscellaneous * Warning boards for overwidth up to 3 m * Contour marking in accordance with ECE-R48 * Technical documentation and TÜV certificate For further information, we are happy to assist you.