Fliegl Vts 400 S Luft/ Hydr. 4-Achs Tieflader Kröp nakup rabljenega (64.819)

Stanje: novo, največja dovoljena obremenitev: 31.920 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 10.410 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, New Fliegl 4-Axle Low Loader Trailer with Ramps, Model VTS 400 Gross weight: 24,000kg / 40,000kg Unladen weight: 8,080kg Payload: 15,920kg / 31,920kg Total length: 11,940mm Total loading length: approx. 10,410mm; Gooseneck: approx. 2,490mm; Loading platform incl. rear bevel: approx. 7,920mm Width: 2,550mm Loading height: 900mm Additional information plus delivery/preparation from stock location 26639 Wiesmoor: €1,280.00 net Leasing offer: term 48 months, down payment only VAT, residual value 40% Monthly instalment EUR 759.00 Chassis Low Loader Trailer Steel welded construction Turntable with heavy-duty ball-bearing slewing ring Foldable rear support 2 wheel chocks with holders Aluminium side underrun protection Full-width rear spray flap Half-shell mudguards on axle 1 + 2 with anti-spray flaps behind each axle Anti-spray flaps before and behind axles 3 and 4 Excavator arm recess over rear axles, stretching to the rear, approx. 1,800mm long, 650mm wide, 150mm deep 2 pairs of lashing holes (5t each) in the excavator arm recess, side-mounted on the longitudinal frame, approx. 300mm from the front and approx. 200mm before the rear bevel 1 plastic toolbox, w=600mm / h=425mm / d=460mm, lockable Storage box recessed into the gooseneck floor with lid, w=720mm / l=520mm / d=170mm Extendable widenings to 3,000mm (not at rear bevel) (Note: the track width of machines or vehicles being transported must not exceed the outer frame width of 2,550mm) Wooden plank compartment under the low-bed platform 70mm wooden planks for extension to 3,000mm Low loader lashing points 1 pair of lashing cutouts sunk in the longitudinal beam at the front of the gooseneck, 10t each 4 pairs of lashing holes in external frame (5t each, suitable for tension belt attachment) 9 pairs of lashing mushrooms set into the external frame above and on the sides, each 10t 2x front on gooseneck 7x low-bed area 1st lashing point 250mm from front, last max. 250mm from rear, max distance between lashing points 1,100mm 3 additional pairs of folding lashing eyes, 10t each: - 1x on gooseneck (protruding) - 1x inside start of low-bed area in longitudinal beams - 1x recessed in floor behind last axle Towing arrangement, turntable trailer Drawbar with certified 50mm draw eye Drawbar height adjustment via spring Axles & Suspension Drum brake axles, manufacturer’s choice Chassis/axle laser alignment (reduces tyre wear and fuel consumption) Air suspension with raise & lower valve + auto reset function Wheels and tyres Nodpfxovv D Ixe Ab Djdb 235/75 R 17.5”, manufacturer’s choice Steel twin wheels, factory silver Braking system 2-line pneumatic brake system Spring-loaded parking brake Axle load detection via EBS CAN-Bus signal (for in-cab display, truck must be pre-equipped, not a calibrated scale) Vehicle stability system 2 foolproof coupling heads at the front, with connecting lines to tractor unit 12-24V EBS (Electronic Braking System) with EBS plug at the front and connecting cable (Knorr brand) Note: Trailer must only be towed by towing vehicles capable of ensuring full ABS functionality! Electrics 12-24V, multi-chamber LED lamps, amber LED side markers, LED license plate lighting (Note: On certain tractor units, malfunction messages may appear even if operational) 2 white position lights at the front (LED) 2 white/red contour marker lights at the rear (LED) 2x 7-pin foolproof connectors at the front

Stanje: novo, največja dovoljena obremenitev: 31.920 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 10.410 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, New vehicle: Fliegl 4-axle low-loader trailer with ramps, model VTS 400 Gross weight: 24,000 kg / 40,000 kg Unladen weight: 8,080 kg Payload: 15,920 kg / 31,920 kg Overall length: 11,940 mm Loading length: total approx. 10,410 mm; neck approx. 2,490 mm; loading bed incl. rear taper approx. 7,920 mm Width: 2,550 mm Loading height: 900 mm Further information: Plus pre-freight / preparation ex stock 26639 Wiesmoor: €1,280.00 / net Chassis: Low-bed trailer Steel welded construction Turntable with heavy-duty ball race ring Foldable rear support 2 wheel chocks with holders Side underrun protection, aluminium Full-width rear mud flap Half-shell mudguards, 1st and 2nd axles with anti-spray flaps behind each axle, Anti-spray flaps in front of and behind 3rd and 4th axles Excavator stick trough over rear axles to the rear, approx. 1,800 mm long, 650 mm wide, 150 mm deep 2 pairs of lashing holes, each 5 t, in the excavator stick trough on the longitudinal frame, approx. 300 mm from the front and 200 mm in front of the rear slope 1 plastic toolbox, w=600 mm / h=425 mm / d=460 mm, lockable Storage box recessed in the neck floor with lid, w=720 mm / l=520 mm / d=170 mm Extendable outriggers to 3,000 mm (not for rear slope) Ndjdpfxexrx Nle Ab Dsb (Track width of construction machinery/vehicles to be transported must not exceed external frame width of 2,550 mm) Storage compartment for wooden planks under the low-bed deck Wooden planks, 70 mm, for extension to 3,000 mm Lashing points, low-loader: 1 pair of lashing cutouts in the front longitudinal beams, embedded in the neck, each 10 t 4 pairs of lashing holes in the outer frame, each 5 t (for attaching ratchet straps) 9 pairs of lashing mushrooms, embedded in and above the outer frame, each 10 t: - 2 × on the neck - 7 × in the low-bed section First lashing point 250 mm from the front, last max. 250 mm from the rear; lashing point spacing max. 1,100 mm Additionally, 3 pairs of folding lashing eyes, each 10 t: - 1 × on the neck (protruding) - 1 × at the start of the low-bed inside the longitudinal beams - 1 × in the floor behind the last axle Drawgear, turntable trailer: Drawbar with certified 50 mm eye Drawbar height adjustment via spring Axles & Suspension: Drum brake axles, per manufacturer’s choice "Axles/chassis laser-aligned" to reduce tire wear and fuel consumption Air suspension with lift & lower valve + auto-reset function Wheels and Tyres: 235 / 75 R 17.5", per manufacturer’s choice Steel twin wheels, factory silver Braking system: 2-line air-operated brake system Spring-loaded parking brake Axle load detection via EBS CAN bus signal for display in truck cab (truck must be equipped accordingly; not a calibrated scale) Vehicle stability system: 2 non-interchangeable coupling heads at the front, connection lines to the tractor 12-24V EBS, electronic braking system with EBS socket at the front, including connecting cable (Knorr brand) Attention: The trailer may only be towed by vehicles that guarantee ABS functionality! Electrics: 12-24V, multi-chamber LED lights, side LED marker lights (yellow), LED license plate lighting (Note: Some towing vehicles may display incorrect errors despite proper function) 2 white front position lights, LED 2 white/red rear lane marker lights, LED 2 × 7-pin non-interchangeable sockets at the front, with connection cable 1 LED rotating beacon with bracket, switchable via sidelights (removable beacon) 2 pairs...

Stanje: novo, največja dovoljena obremenitev: 31.100 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 10.410 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.520 mm, Gross weight: 24,000kg / 40,000kg Curb weight: 8,900kg Payload: 15,100kg / 31,100kg Total length: 11,940mm Loading length: 10,410mm total, 2,490mm gooseneck, 7,920mm loading deck including rear bevel Width: 2,520mm Loading height: 900mm Further information: plus pre-carriage / provision ex stock location 26639 Wiesmoor: €1,280.00 net Steel welded construction Turntable with heavy-duty ball-bearing slewing ring Foldable rear support Wheel chocks with holder Aluminium side underrun protection Rear mudflaps across the full width (not in combination with forklift holder) Half-shell fenders on 1st and 2nd axles with anti-spray mudflaps behind each axle Anti-spray mudflaps in front of and behind 3rd and 4th axles Excavator arm recess over rear axles to the rear, approx. 1,800 mm long, approx. 650 mm wide, approx. 150 mm deep 2 pairs of lashing holes (5 t each) in the excavator recess at the side of the longitudinal frame, approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable 1 storage box embedded in gooseneck floor with lid, W=720 mm / L=520 mm / D=170 mm Extendable width to 3,000 mm (not in rear bevel) (Track width of machines/vehicles to be transported must not exceed outer frame width of 2,550 mm) Storage compartment for timber planks under low-bed platform 70 mm timber for widening to 3,000 mm Low loader lashing eyes 1 pair of lashing cut-outs at the front longitudinal member in gooseneck, each rated 10 t 4 pairs of lashing holes in the outer frame, each 5 t (lashing strap attachment) 9 pairs of recessed lashing mushrooms in the outer frame, top and side, each 10 t 2 x front on gooseneck 7 x in lowered bed First lashing eye 250 mm from the front, last max. 250 mm from the rear, spacing not greater than 1,100 mm 3 pairs of additional folding lashing eyes, each 10 t: 1 x on gooseneck (protrudes) 1 x at beginning of low bed, recessed in longitudinal rails 1 x behind the last axle, recessed in the floor Trailer tow device Drawbar with certified 50 mm towing eye Drawbar height adjustable by spring Axles & suspension Drum brake axles, manufacturer's choice Axles/chassis laser aligned—reduces tire and fuel wear Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (equalisation rocking beams) Wheels and tires 235/75 R 17.5" manufacturer's choice Steel rims in twin configuration, factory silver Braking system 2-line compressed air brake system Spring-loaded parking brake 2 foolproof coupling heads at the front with connection leads to tractor unit 24 Volt ABS and ALB, with ABS connector at front, with connecting cable Note: The trailer may only be towed by tractors supporting ABS function! Electrics 12–24 volt, multi-chamber LED lamps, side yellow LED marker lights, LED license plate lights (note: some tractors may show false diagnostics despite correct function) 2 white position lights at the front, LED 2 white/red lane marker lights at the rear, LED 2 x 7-pin foolproof connectors at the front, with connecting cable 1 LED beacon with holder, switched via position light (removable beacon) 2 pairs of warning plates, double LED illuminated and extendable to 3,000mm Floor Gooseneck front with steel/checker plate covering then approx. 70 mm softwood floor, in the wheel arch area steel/checker plate covering Rear bevel with 70 mm softwood floor Ndsdpfx Asrducpeb Deb A

Stanje: rabljeno, največja dovoljena obremenitev: 29.940 kg, konfiguracija osi: > 3 osi, prva registracija: 03/2011, 4-osni prikolica z nizko nosilnostjo Feitzinger VTS 400 z največjo dovoljeno maso 40.000 kg in lastno težo 10.060 kg, s sistemom vzmetenja na listnih vzmeteh. Nagibna rampa, zložljiva s pomočjo hidravlike. Stanje: dobro. Stanje pnevmatik: 60-80 %. Ndsdpfx Abjz Dzi Ne Djb --- Tehnične specifikacije: Splošno: * Kratka opis: Feitzinger VTS 400, 4-osna prikolica z nizko nosilnostjo, s sistemom vzmetenja na listnih vzmeteh in zložljivo rampo. * Dovoljena skupna masa vlečne enote: 40.000 kg. Kabina: * Hladilnik: Ne. Motor: * AdBlue: Da. Prenos: * Retarder: Ne. Podvozje: * Vzmetenje: Vzmetenje na listnih vzmeteh. * Litje platišč: Ne. * Dvignjena os: Ne. * Krmiljena os: Ne. Prijeklica: * Prijeklica za invalide: Ne. Dokumentacija: * Lastna teža: 10.060 kg.

Stanje: rabljeno, največja dovoljena obremenitev: 31.700 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, prva registracija: 08/2022, dolžina tovornega prostora: 7.920 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, skupna dolžina: 11.940 mm, skupna širina: 2.520 mm, Skupna masa: 24.000 kg / 40.000 kg Lastna masa: 8.300 kg Nosilnost: 15.700 kg / 31.700 kg Skupna dolžina: 11.940 mm Dolžina tovornega prostora: skupaj približno 7.920 mm Širina: 2.520 mm Višina tovornega prostora: 900 mm Dodatne informacije: - pocinkano - vzmetenje s paraboličnimi vzmetmi - hidravlične rampe, jeklo, prevlečene z lesom, stransko pomične - predal za orodje - velik komplet priveznih pasov - opozorilni znaki spredaj in zadaj - plastičen predal za orodje - zadnji oporni sistem, zložljiv - korito za bager, ki se začne nad zadnjo osjo in sega do zadnje strani, približno 1.800 mm x 650 mm, približno 150 mm globoko Ndodpfx Aez Am U Deb Dsb - razširitev na 3 m - predal za orodje z lesenimi deskami pod tovorno površino

Stanje: novo, največja dovoljena obremenitev: 30.010 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 10.000 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, New vehicle: Fliegl 4-axle low-loader trailer with wheel recesses and split ramps, type VTS 400 RM Lease-purchase offer: Term 48 months, down payment only the VAT, residual value 40% Monthly rate: EUR 899.00 Vehicle / Body: Low-loader First registration: New vehicle Gross weight: 24,000 kg / 40,000 kg Unladen weight: 9,990 kg Payload: 14,010 kg / 30,010 kg Overall length: 12,000 mm Loading length: total approx. 10,000 mm, gooseneck approx. 2,850 mm, load area including rear bevel approx. 7,150 mm Width: 2,550 mm Loading height: 900 mm Further information Low-loader trailer chassis Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear supports Wheel chocks with holders Aluminum side underrun protection Rear spray flap across the entire width Half-shell mudguards on 1st and 2nd axle with anti-spray flaps behind each axle, anti-spray flap behind 4th axle Excavator arm recess above the rear axles, extending to the rear, approx. 1,800 mm long, approx. 650 mm wide, and approx. 150 mm deep 2 pairs of lashing holes (5 t each) in the excavator arm recess, lateral on the main frame approx. 300 mm from the front and approx. 200 mm before the rear bevel Ndsdpfxjtrizkj Ab Djb Spare wheel carrier for 1 spare wheel, upright on the gooseneck right at the front. Spare wheel, make identical to the main tires, steel rim Storage box recessed in the gooseneck floor with lid; dimensions W = 720 mm / L = 520 mm / D = 170 mm 1st pair of wheel recesses after the gooseneck, recessed in the low-bed lane area, ramped for entry, bottom length approx. 1,600 mm, depth approx. 400 mm. Note: Frame in the main beam area is 400 mm higher than the wheel recess 2nd pair of wheel recesses between the axles, recessed in the low-bed lane area, ramped for entry, bottom length approx. 600 mm, depth approx. 300 mm. Note: Frame in the main beam area is 300 mm higher than the wheel recess Extendable width up to 3,000 mm (not extendable in the rear bevel and not in the lower wheel recesses) (track width of the construction equipment or vehicles to be transported must not exceed the external frame width of 2,550 mm) Storage compartment for wooden planks below the low-bed area 70 mm wooden planks for extension to 3,000 mm Lashing eyes on the low-loader 1 pair of lashing eyes, recessed in the front of the gooseneck, 5 t each 4 pairs of lashing holes in the outer frame, 5 t each (for lashing straps) 8 pairs of lashing rings, integrated on top and side of outer frame, 10 t each 2 at the front on the gooseneck 6 in the low bed First lashing point 250 mm from the front and last max. 250 mm from the rear, spacing between lashing points not greater than 1,100 mm 5 pairs of stake pockets integrated in the outer frame, inside 70 x 40 mm (convertible to 5 t ring lashing eyes, not included) 1 pair of folding lashing eyes, additionally recessed in the floor, 10 t each 1 inside next to the main frame at the start of the low bed 2 pairs of additional folding lashing eyes, 10 t each 1 on the gooseneck (protrudes over edge) 1 behind last axle, recessed in floor Drawbar coupling / turntable trailer hitch Towing bar with certified 50 mm towing eye, towing eye inclined 8° D-value at least 160 kN Axles & suspension BPW drum brake axles "Axle/chassis laser alignment" reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical front axle load equalization (rocker balance) Wheels and tires 235 / 75 R 17.5" Manufacturer's choi

Stanje: novo, največja dovoljena obremenitev: 30.310 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, NEW VEHICLE Fliegl 4-axle low loader with 2 pairs of wheel recesses and ramps Gross weight: 40,000 kg Payload: 30,310 kg Unladen weight: 9,690 kg Overall length: 12,000 mm Loading length: 10,000 mm Loading bed: 7,150 mm including 850 mm drive-on slope Loading height: 900 mm 1st pair of wheel recesses after drop in the loading bed, length at bottom approx. 1,600 mm, 400 mm deep 2nd pair of wheel recesses between the axles in the loading bed, length at bottom 600 mm, 300 mm deep Extensions to 3,000 mm, warning boards, rotating beacon, comprehensive lashing package 5 pairs of stake pockets in the outer frame Excavator arm recess, 1,800 mm long, 150 mm deep Drawbar 50 mm Air suspension with raise/lower valve, separately operable BPW drum brakes Tyres: 235 / 75 R 17.5" Ndsdpfxsnzlg Ds Ab Deb Axle load detection via EBS CAN bus signal, Trailer Info Center Ramps: 2,800 mm x 750 mm, hydraulically operated Hydraulic lateral displacement Hire purchase offer: term 48 months, residual value 40%, down payment only the VAT on the installments, monthly payment EUR 970.00 net Vehicle available from 11.09.2023 from the Neumünster trade fair. Visit us at Nordbau - Stand West 121, right next to the main entrance. Further 3-, 4- and 5-axle low loaders new and used available immediately

Stanje: rabljeno, največja dovoljena obremenitev: 31.880 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, prva registracija: 02/2015, Črna prikolica z 4 osmi, pocinkana, z nizko nosilno ploščjo in hidravličnimi rampami, razširjiva na 3 m, z žlico za bager. Nedpoz Dzi Ajfx Ab Dedb Stanje: glede na starost, dobro. Pnevmatike: 60-80 %. --- Tehnične specifikacije: Splošno: * Kratka opis: prikolica z nizko nosilno ploščjo in hidravličnimi rampami, 4 osi, pocinkana, razširjiva. Kabina: * Hladilnik: Ne. Motor: * AdBlue: Da. Menjalnik: * Retarder: Ne. Podvozje: * Aluminijasta platišča: Ne. * Dvignjena os: Ne. * Usmerjevalna os: Ne. Povezava z vlečnim vozilom: * Povezava za prikolice za invalide: Ne. Dokumentacija: * Prazna teža: 8.120 kg.

Stanje: rabljeno, največja dovoljena obremenitev: 31.880 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, prva registracija: 02/2015, Leto izdelave: 2015, Schwarzmüller, prikolica s 4 osmi, pocinkana, nizkotilna z hidravličnimi rampami, razširjiva na 3 m, s žlico za izkop. Stanje: glede na starost, dobro. Pnevmatike: 60–80 %. Ndsdpfez D Rl Hsx Ab Dsb ----Tehnične specifikacije: Splošno: ? Kratka opis: Nizkotilna prikolica s 4 osmi in hidravličnimi rampami, razširjiva, pocinkana. Kabina: ? Hladilnik: Ne. Motor: ? AdBlue: Da. Prestavna škatba: ? Zaviranje z retarderjem: Ne. Podvozje: ? Litje platišč: Ne. ? Dvigalna os: Ne. ? Vodena os: Ne. Sedelna sklopka: ? Sedelna sklopka za invalide: Ne. Dokumenti: ? Prazna teža: 8.120 kg.

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: Produktpalette, skupna masa: 24.000 kg, konfiguracija osi: > 3 osi, višina nakladalnega prostora: 900 mm, skupna dolžina: 11.940 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 235 / 75 r 17,5, stanje pnevmatik: 100 odstotek, Further Information Chassis Low-loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Side underrun protection made of aluminium Full-width rear mudflap Half-shell fenders on 1st and 2nd axle with anti-spray mudflaps behind each axle; anti-spray mudflaps in front of and behind 3rd and 4th axle Excavator arm recess over the rear axles, starting to the rear, approx. 1800 mm long, approx. 650 mm wide, and approx. 150 mm deep, 2 pairs of lashing holes each rated 5 t located laterally in the excavator arm recess in the main chassis, approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 plastic toolbox with shelf, w=620/h=360/d=440 mm, lockable with a padlock (Padlock not included) 1 storage box let into the gooseneck in the floor with lid, w=720 mm/ l=520 mm / d=170 mm Extendable width to 3,000 mm (not at the rear bevel) (the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) 70 mm timber planks for widening to 3,000 mm Storage compartment for timber planks under the loading platform Lashing rings low-loader (40 lashing possibilities) Nedpfxei Ri Das Ab Dodb 1 pair of lashing rings on gooseneck, each 5 t 9 pairs of lashing mushrooms recessed into the outer frame, top and side, each rated 10 t 2 x in the front on the gooseneck 7 x in the low-bed 6 pairs of lashing holes in the outer frame of the low-bed, each rated 5 t (for lashing strap hooks) 3 additional pairs of folding lashing rings, each rated 10 t 1 x inside beside the main frame at the beginning of the low-bed 1 x on the gooseneck (protruding) 1 x recessed into the floor behind the last axle Drawbar coupling for turntable trailer Drawbar with certified 50 mm towing eye, towing eye inclined at 8°, D-value at least 160 kN Axles & Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker equalisation) Wheels and Tyres 235 / 75 R 17.5 manufacturer’s choice Steel rims, twin mounting, factory silver Brake System 2-line compressed air brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, including connection lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connection cable Electrics 24 volt, multi-chamber lamps, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin non-interchangeable plugs at the front with connecting cable 1 LED beacon with holder, operated via parking light (beacon removable) 2 pairs of warning boards, double LED illuminated and extendable to 3,000 mm Flooring Gooseneck at front with steel/chequer plate floor Then with 70 mm softwood floor, in wheel arch area steel/chequer plate covering Rear bevel with 70 mm softwood floor Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber decked Hydraulically operated via tractor PTO with restrictor, control located on the left side at the front Hydraulic connection with SVK connector NW 10/3, incl. connecting hose Registration Country/Plates Registration country: Germany 24/7 Service Hotline Prepared for two-line number plate holder Contour marking with reflective strips according to ECE R 048, side white and rear red Warning plate according to ECE – 70 Paintwork Chassis hot-dip galvanized including passivation, 15-year warranty again

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: WFDFLT44001000966, lastna masa: 9.400 kg, največja dovoljena obremenitev: 30.600 kg, skupna masa: 40.000 kg, konfiguracija osi: > 3 osi, prva registracija: 10/2010, dolžina tovornega prostora: 7.145 mm, širina tovornega prostora: 2.750 mm, višina nakladalnega prostora: 900 mm, skupna dolžina: 12.120 mm, skupna širina: 27.500 mm, skupna višina: 900 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R17,5", barva: rdeča, These images are for reference only! Nedeyxq A Hjpfx Ab Djdb Gross weight perm. / technical: 24,000 / 40,000 kg Payload perm. / technical approx.: 14,600 / 30,600 kg Axle load perm. / technical: 24,000 / 40,000 kg Unladen weight (base version) approx.: 9,400 kg +/- build tolerance Overall length approx.: 12,120 mm Overall width max.: 2,750 mm Neck length approx.: 2,850 mm Low loader platform length in driving lane area incl. rear bevel approx.: 7,145 mm Rear bevel length approx.: 850 mm Frame width approx.: 2,750 mm Loading height in the low bed (loaded) approx.: 900 mm Tow height approx.: 950 mm Drawbar length approx.: 1,700 mm Chassis Low Loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Side underrun protection, aluminium 1 plastic toolbox Extendable widenings to 3,250 mm (not at rear bevel) (tracking width of transported construction machines or vehicles must not exceed outer frame width of 2,750 mm) Central storage compartment for wooden planks 70 mm wooden planks for widening to 3,000 mm 2 pairs of stake pockets in the low bed, integrated in the floor longitudinal beams Lashing rings, low loader: 2 pairs of lashing rings on the neck, each 5 t 1 pair of lashing rings in the rear bevel 4 recessed lashing rings, placed centrally in the floor 2 pairs of key slot profiles in the driving lane, for longitudinal guide rails and as additional lashing points 6 pairs of lashing mushroom anchors in the low bed outer frame, each 10 t 5 pairs of stake pockets in the outer frame of the low bed 4 additional pairs of 10 t lashing rings: 1 on the neck 3 recessed in the floor of the low bed Drawbar coupling, turntable trailer: Drawbar with tested 50 mm towing eye Axles + suspension: Drum brake axles Parabolic spring suspension with maintenance-free steel-rubber bearings and mechanical axle load equalization front and rear (rocker leveling) Wheels and tires: 235 / 75 R 17.5" Steel rims, twin arrangement, factory silver Brake system: 2-line air brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front with connection lines for towing vehicle ABS and ALB, with ABS connector at front, with connection cable Attention: The towed trailer may only be pulled by towing vehicles that ensure proper function of the ABS! Floor: Neck area with steel/chequer plate flooring then 70 mm softwood floor, wheel recesses with steel/chequer plate flooring Rear bevel with 70 mm softwood floor Access ramps: Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber surface Hydraulically operated via tractor PTO Operating instructions: For 10,000 kg axle load, a special permit is required, only indivisible loads permitted!!! Note! Overlength and excess width, special permanent approval required. For applications for special permits for heavy-duty transport, an axle load display is required for air-suspended vehicles! This applies to all deviations from § 34 StVZO (axle load and permissible gross weight exceedance) that require a special permit under § 70 StVZO. The declared gross weight is technically feasible; depending on the load, the gross vehicle weight may not be achievable while observing permissible axle, support, and saddle loads. (Poor driving and trailing behavior possible due to incorrect load distribution) These images are for reference only!

Stanje: rabljeno, največja dovoljena obremenitev: 37.530 kg, skupna masa: 50.000 kg, konfiguracija osi: > 3 osi, prva registracija: 02/2012, naslednji pregled (TÜV): 11/2026, skupna širina: 3.000 mm, skupna višina: 3.780 mm, Oprema: ABS, * Gooseneck with foldable side walls * Low bed length: 11,950 mm - 15,450 mm * Low bed extendable in steps by 3,500 mm * Low bed width extendable by 460 mm * Hydraulically adjustable loading ramps (split, 2 parts) * Stake pockets * Wabco SmartBoard * 4 axles with twin tires * 1st axle liftable * 3rd + 4th axle with steering function Nsdoy T Dyzspfx Ab Dedb * Wheel chocks ----* Tire size: 235/75R17.5 * Technical gross weight: 58,000 kg * Unladen weight: 12,470 kg * Overall length: 13,700–17,200 mm * Overall width: 2,540–3,000 mm * Safety inspection due: 05/2026 ----Vehicle number: 12062----Subject to errors and prior sale----Advertising and various lettering have been digitally removed.----We are happy to assist you with all the formalities involved in purchasing a vehicle. Simply let us know your wishes and suggestions—we will take care of everything. Among other services, we can offer you the following for an additional fee:----* Trade-in of your old vehicle * HU/Safety inspection * Complete export processing * Financing brokerage * Application for export license plates * Vehicle transfers * Vehicle registration * Recovery and vehicle transport ----?YOUR VTS TEAM

Stanje: rabljeno, prva registracija: 03/2009, skupna masa: 40.000 kg, lastna masa: 8.150 kg, barva: modra, vrsta prenosa: drugo, emisijski razred: noben, največja dovoljena obremenitev: 31.850 kg, naslednji pregled (TÜV): 09/2027, vzmetenje: zrak, dolžina tovornega prostora: 9.800 mm, širina tovornega prostora: 2.510 mm, velikost pnevmatike: 235/75 R17.5, velikost sprednje pnevmatike: 235/75 R17.5, velikost zadnje pnevmatike: 235/75 R17.5, voznikova kabina: drugo, Oprema: ABS, dodatne luči, meglenke, osvetlitev, registracija tovornjaka, zavorni sistem na stisnjen zrak, šasija, Müller-Mitteltal T4 Kompakt – nizkotilnik * Osnove za obračanje – 40-milimetrske + 50-milimetrske * razširitev na 3 m, vključno s stranskimi nosilci * hidravlične rampe, ročno nastavljive po širini * kamera za vzvratno vožnjo * bobnaste zavore * 1 rotacijska luč zadaj * vzmetenje na zračni blazinici * dvojne pnevmatike * osi Gigant * ABS + priključki DUO-Matic * table za označevanje presežne širine spredaj in zadaj * pnevmatike: 235/75 R17.5 * jeklena škatla na podstavku * dolžina rampe: 2,90 m * mere: notranje: D – 9,80 m, Š – 2,55 m * višina roba tovornišča na podstavku: 1,05 m, višina roba tovornišča zadaj: 0,85 m * teže: GVM – 40.000 kg, GVW – 8.150 kg, NV – 31.850 kg * nemško vozilo in nemška dokumentacija!! * 2. lastnik!! * datum prve registracije: 20. 03. 2009 * nov tehnični pregled do 09/2027 * nov varnostni pregled do 03/2027 * VIN: WMM000009052911 Pridržujemo si pravico do spremembe cen, napak in vmesne prodaje! Na nekaterih slikah so bila odstranjena logotipa podjetja – prosimo, povprašajte. Delovanje dodatne opreme ni zagotovljeno. Vaš kontakt: Ndjdpfx Absz Dv Iys Deb Christoph Ott Tel. + WhatsApp:

Stanje: rabljeno, Funkcionalnost: omejena funkcionalnost, lastna masa: 6.575 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 9.000 kg, dovoljena osna obremenitev (os 2): 9.000 kg, dovoljena osna obremenitev (os 3): 9.000 kg, prva registracija: 07/2011, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 1.300 mm, skupna dolžina: 13.650 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 385/65R22,5, stanje pnevmatik: 30 odstotek, medosna razdalja: 1.360 mm, Leto izdelave: 2011, Oprema: ABS, Rabljen odprt polpriklopnik Ndodpfx Ajy Ercbeb Dsb Jeklena sprednja stena z izbočenjem za dolge jeklene profile Tla okrepljena z jeklenimi profili Stranski žepki za stebričke Skladiščna škatla za vstavljive stebričke

Stanje: rabljeno, prva registracija: 11/2006, Leto izdelave: 2006, MÜLLER - MITTELTAL T4 Kompakt Vrtljiva prikolica - Nizkopodna prikolica z zračno vzmetenimi in jamskimi kolesi - 4 x zračno vzmetene GIGANT - osi - zračno vzmetenje - 4 x kolesne jame - mehanske nakladalne rampe - 2 zadnja podporna noga, zložljiva - izvlečne opozorilne table - ABS Ndedpfowmpbdsx Ab Dsb - MICHELIN pnevmatike: 235/75 R 17.5 - težka izvedba: 40.000 kg skupne mase - lastna teža: 8.400 kg - skupna dolžina: 11.750 mm - vlečna zanka: 50 mm Posebej primerna za prevoz strojev za rezanje apna! - nemška prikolica - Tehnični pregled / tehnični preizkus možen na zahtevo in za doplačilo! Pridržujemo si pravico do napak in vmesne prodaje!

Stanje: rabljeno, lastna masa: 15.900 kg, največja dovoljena obremenitev: 48.100 kg, skupna masa: 62.000 kg, konfiguracija osi: > 3 osi, prva registracija: 01/2023, vzmetenje: zrak, velikost pnevmatike: 235/75R17,5, Oprema: ABS, | BODEX nizkopodna prikolica | Poglobitve za kolesa | Zadnji dve osi imata možnost naklona | 1 os je dvižna | Možnost podaljšanja do 6 metrov | Dolžina nosilne površine 13200 mm | Osnova SAF z bobnasto zavoro | Lastna teža: 15900 kg | Skupna masa: 62000 kg | 245/70R17,5 dvojne pnevmatike | Hidravlične rampe, robustna izvedba, dolžina 3800 mm in širina 800 mm. Ndodpfx Aozzdfkjb Dsb

Stanje: novo, največja dovoljena obremenitev: 26.100 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, Vehicle / Body: Low-bed semi-trailer First registration: New vehicle Gross weight: 35,000 kg / 47,000 kg Unladen weight: 8,900 kg Payload: 26,100 kg / 38,100 kg Overall length: 13,300 mm Loading length: 9,200 mm Width: 2,520 mm Loading height: 900 mm Further information Chassis: Low-bed semi-trailer Steel welded structure, fifth wheel plate with replaceable 2" king pin and two king pin positions (not in combination with forced steering) 24 t 2-speed landing gear, single-sided operation, with straight lower part, without thrust compensation Rear support foldable 2 wheel chocks with holders Side underrun protection, aluminium Full-width rear mudflap Mud flaps with anti-spray in front of the 1st axle and behind each axle, in accordance with EU regulations 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Extendable width to 3,000 mm (not at the rear taper) (Note: The track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Compartment for wooden planks on neck, transverse at front 70 mm wooden planks for extension to 3,000 mm Excavator arm recess over rear axles, extending to the rear, approx. 3,000 mm long, 650 mm wide, and 230 mm deep 2 pairs of lashing holes, each rated 5 t, in the excavator arm recess on side of main frame, approx. 300 mm from front and some 200 mm before rear taper Lashing points low-loader 11 pairs of lashing mushrooms, integrated top and side of the outer frame, each 10t 2x on gooseneck 9x distributed on load floor 2 pairs of lashing eyes front on gooseneck, each 5t 3 pairs of swivel lashing eyes on gooseneck, each 5t Ndsdpfeut Idnjx Ab Dsb 2 pairs of folding lashing eyes additionally embedded in load floor, each 10t 1x at beginning of load floor 1x at end of rear taper 1 pair of preparation on the slope from gooseneck for 6.7t screw-on lashing eye (JDT) 8 pairs of ring lashing eyes recessed in outer frame, each 5t (convertible to stanchion pockets) 1 pair screw-on lashing eyes, each 6.7t (JDT), with large flange plate incl. thread as counternut Axles & suspension SAF or BPW drum brake axles, manufacturer's choice “Axle/chassis laser alignment” to reduce tire wear and fuel consumption Last axle is self-steering, with automatic reversing lock via reversing light and additional manual lock function via push button on vehicle Air suspension Wheels and tires 235 / 75 R 17.5" Manufacturer's choice Steel rims, twin configuration, factory silver Braking system 2-line compressed air brake system Coloured line routing for easy service Spring-loaded parking brake 24 Volt EBS, electronic braking system with EBS socket at front, without connecting cable Note: The trailer may only be towed by tractor units that ensure effective ABS functionality! 2 coded coupling heads at front, without connecting line With lift & lower valve Axle load detection via EBS-CAN-bus signal, for display in cab, truck must be appropriately equipped, no truck installation (not a calibrated scale) Vehicle stability control system Tire pressure monitoring system according to ECE R 141, display in tractor cab via EBS, truck installation required Electrics 24 Volt, multi-chamber lights, side yellow LED lighting Side yellow LED lighting linked to indicator "flashing side markers" 2 white position lights at front 2 white/red lane marker lights at rear 2x 7-pin coded sockets at front, without connecting cable 1 LED revolving beacon

Stanje: rabljeno, največja dovoljena obremenitev: 34.440 kg, skupna masa: 46.500 kg, konfiguracija osi: 3 osi, prva registracija: 06/1999, dolžina tovornega prostora: 13.550 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 950 mm, skupna širina: 2.550 mm, Skupna masa: 46.500 kg Lastna masa: 12.060 kg Nosilnost: 34.440 kg Skupna dolžina: 13.550 mm - 26.550 mm Širina: 2.550 mm Dodatne informacije: - 3 osi, hidravlično prisilno krmiljenje - priključek za nadstandardno dolge tovornjake - palica za pritrditev rampe - priključni elementi za nakladalno površino - dvojna teleskopska konstrukcija, raztegljiva do 26.550 mm - orodjarna na prikolici - električno vodeno kolo - možnost namestitve dodatnih širitev - hidravlična funkcija za dodatno krmiljenje, upravljanje na daljavo - velik komplet pritrdilnih pasov - lastna hidravlična črpalka Nsdoycpbnjpfx Ab Dodb Na voljo so tudi drugi novi in rabljeni prikolice za nadstandardne tovore. Dodatne informacije najdete na:

Stanje: novo, lastna masa: 6.600 kg, največja dovoljena obremenitev: 17.400 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, skupna dolžina: 10.900 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R17,5 (Doppelbereifung), barva: srebrn, vrsta prenosa: mehanski, poraba goriva (mestna vožnja): 1.090 l/100 km, Unladen weight: 6,600 kg, permissible gross weight: 24,000 kg, tyre size: 235/75 R17.5, 1st axle: , 2nd axle: , 3rd axle: , leaf suspension, weights: Immediate approval technically possible Gross weight: 24,000 kg, 30,000 kg, payload approx.: 17,400 kg, 23,400 kg; unladen weight approx.: 6,600 kg +/- manufacturing tolerance. Dimensions (approx.): Total length 10,900 mm, total width 2,550 mm, gooseneck length 2,180 mm, low bed platform length incl. rear chamfer 6,500 mm, rear chamfer length 950 mm, frame width 2,520 mm, loaded loading height in low bed 860 mm, coupling height 900 mm, drawbar length 1,900 mm. Equipment: - Extendable width up to 3,000 mm (not in rear chamfer), incl. timber planks - SAF drum brake axles - Parabolic suspension - Drawbar with certified 40 mm towing eye - Tyres 235/75 R17.5 - Storage box recessed at the transition to the gooseneck - 1 plastic toolbox with shelf, 620 mm wide / 360 mm high / 440 mm deep - Steel ramps: 2,800 mm long, 750 mm wide, laterally adjustable, timber-coated - Ramps with spring assist - Frame hot-dip galvanised Subject to errors and changes. Ndjdpfxsx Nrp No Ab Dsb

Stanje: novo, lastna masa: 6.600 kg, največja dovoljena obremenitev: 17.400 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 6.500 mm, skupna dolžina: 10.900 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R17,5 (Doppelbereifung), barva: srebrn, vrsta prenosa: mehanski, poraba goriva (mestna vožnja): 1.090 l/100 km, Unladen weight: 6,600 kg, permissible gross weight: 24,000 kg, cargo area length: 6,500 mm. Tyre size: 235/75 R17.5. 1st axle: , 2nd axle: , 3rd axle: . Leaf suspension. 3-axle low-bed trailer with drop-bed DTS-S 300 - Turntable with robust ball bearing ring - Rear supports, foldable - 1 spare wheel carrier for 1 spare wheel, incl. wheel mounting kit - 1 spare wheel, same brand and type as main tyres, steel rim - 1 plastic toolbox - Extendable load width up to 3,000 mm (not in rear slope) - Storage compartment for timber planks in the centre of the low-bed platform - Timber planks, 70 mm, for widening to 3,000 mm Tie-down points on low-bed: - with spring-loaded lifting aid Axles + suspension: - SAF - Drum brake axles - Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalisation (rocker compensation) Braking system: - Dual-line compressed air brake system - Spring-loaded parking brake Electrics: - 24 Volt, multi-chamber lights, yellow LED side lights - 1 LED beacon with mounting bracket, controlled via parking light (removable beacon) - 2 pairs of warning boards, double LED illuminated, extendable to 3,000 mm Floor: - Storage box recessed into drive-up angle at the drop bed - Then 70 mm softwood floor, steel/chequer plate covering in wheel arch area - Rear slope with 70 mm softwood floor Ramps: Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable, covered with wood - 1 pair of ring lashing eyes recessed front in drop bed, 10 t - 4 pairs of lashing holes in rear area, 5 t each for tensioning strap hooks - 7 pairs of lashing points recessed top and side in outer frame, 10 t each (1 x front in drop bed, 6 x in low bed) - 5 pairs of stanchion pockets recessed in outer frame, inside 70 x 40 mm (convertible to 5 t ring lashing eyes for extra cost) - 2 additional pairs of folding lashing eyes, 10 t each, 1 x front in drop bed, 1 x behind 3rd axle Axles + suspension: Njdpotcwkrjfx Ab Dsdb - SAF - Drum brake axles - Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalisation

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, lastna masa: 8.000 kg, največja dovoljena obremenitev: 39.000 kg, skupna masa: 47.000 kg, konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 13.000 kg, dovoljena osna obremenitev (os 2): 13.000 kg, dovoljena osna obremenitev (os 3): 13.000 kg, prva registracija: 07/1983, dolžina tovornega prostora: 11.870 mm, širina tovornega prostora: 2.500 mm, vzmetenje: parabolično listje (vzmet), barva: bela, Leto izdelave: 1983, Polpriklopnik CTC ZA90SRT47 Nizkopodni 11,87 m s hidravličnimi rampami in vitlom (4,10 m + 7,35 m) 3 osi Nsdpoy Axufefx Ab Dodb Parabolično vzmetenje Dovoljena skupna masa 47.000 kg – nosilnost 39.000 kg Za specialne prevoze, dovoljena skupna masa kompozicije 56.000 kg Neto izvozna cena: 18.000,00 EUR Vse informacije brez garancije/ možnost napake pridržana.

Stanje: novo, največja dovoljena obremenitev: 35.240 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.200 mm, skupna dolžina: 13.200 mm, skupna širina: 2.550 mm, Leto izdelave: 2026, Oprema: ABS, Kässbohrer K.SLH S HS 3 / 3H ? 18 / 30 – nizkopodna prikolica / 3-osna / hidravlično krmiljena Takoj na voljo, na voljo tudi z rešetkastim dnom. Proizvajalec: Kässbohrer * Tip: K.SLH S HS 3 / 3H ? 18 / 30 * 3-osna nizkopodna prikolica * Osne osi BPW * Zračna vzmetitev * Bobnaste zavore * 1., 2. in 3. os hidravlično krmiljena * Dviganje osi * Ročno upravljanje dviganja osi * WABCO EBS 2S/2M z ABS in RSS * Pnevmatike: 245/70 R17.5 * Pnevmatike M+S / 3PMSF * Sistem za nadzor tlaka v pnevmatikah * WABCO SmartBoard * Električna motorna črpalka za krmiljenje * Polavtomatsko vključevanje hidravlično krmiljene osi Dimenzije / Teže: Zunanja dolžina: 13.250 mm * Skupna širina: 2.550 mm * Višina sedla: 1.250 mm * Dolžina gosi: 3.900 mm * Dolžina platforme: 9.300 mm * Višina platforme: 875 mm * Medosjna razdalja: 8.800 mm * Osna razdalja: 1.360 mm * Prazna teža: približno 12.760 kg * Tehnična osna obremenitev: 30.000 kg * Obremenitev pete: 18.000 kg Ndodpfez Ec Trjx Ab Deb * Tehnična skupna teža pri 80 km/h: 48.000 kg * Tehnična skupna teža pri 40 km/h: 51.000 kg Wiese Transporttechnick - zastopnik Podvozje / Tovorna površina: Visoko trpežno jeklo S700 MC * 45 mm trd lesena podlaga * Jeklena podlaga s kapljičasto strukturo nad kolesi * Stranske podaljške * Podaljšek do 300 mm * 2" pete * Mehanske zadnje opore, nosilnost 45 t * Delno metalizirano podvozje * Zadnji del, nagnjen za 500 mm / 10° Wiese Transporttechnick - zastopnik Rampe: Hidravlične, zložljive rampe * Nosilnost rampe: 40 t * Dolžina rampe: 2.750 mm * Širina rampe: 850 mm * Hidravlično pomična * Trdna lesena prevleka * Hidravlične rampe za gosji vrat * Varovanje rampe s pomočjo napenjalnih verig Wiese Transporttechnick - zastopnik Varovanje tovorja / Oprema: Vezalne točke: 10 × 10 t / 12 × 8 t / 22 × 5 t * 16 žepov za vezne točke 80 × 80 mm * 4 žepi za zaklepanje kontejnerjev za 1 × 20 ft * Orodjarna na gosi, približno 2.540 × 600 × 460 mm * Centralni sistem za podmazovanje * LED rotacijska luč * 2 delovni reflektorja zadaj * Izvlečne opozorilne table z LED pozicijskimi lučmi * Predal za shranjevanje podaljškov * Barva podvozja: RAL 3020 prometna rdeča Drugo: LED osvetlitev * Aspöck EUROPOINT 3 LED * Držalo za rezervno kolo * 12 platišč/pnevmatik * Podaljševalne plošče * Obsežna oprema za težke / gradbene stroje Napake, spremembe in prodaja vmesnih zalog pridržane.

Stanje: skoraj kot novo (rabljeno), Funkcionalnost: popolnoma funkcionalen, prva registracija: 03/2026, stanje pnevmatik: 100 odstotek, Leto izdelave: 2025, Prikolica je v odličnem stanju, skoraj nova. Opremljena je s hidravličnimi rampami, ki se premikajo mehansko. Ima tudi vdolbinice za kolesa. Nodpfx Aozrb Idjb Dodb

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: Produktpalette, lastna masa: 14.300 kg, največja dovoljena obremenitev: 9.700 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 900 mm, skupna dolžina: 12.000 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 235 / 75 r 17,5, stanje pnevmatik: 100 odstotek, Rešitev po meri za transport Konfigurirajte svoje vozilo Fliegl glede na vaše zahteve. Prikazano vozilo je zgolj primer. Proizvodnja in oprema se izvedeta individualno po želji stranke. Dodatne informacije Podvozje Jeklena varjena konstrukcija Vrtljiva plošča z robustnim krogličnim ležajem Zložljivo zadnje podpiranje 2 zagozdi za kolesa + nosilec Bočna zaščita iz aluminija Zadnje blatne zavese po celotni širini Četrtinski blatniki pred 1. osjo Izkop za roko bagra nad zadnjimi osmi do zadka, približno 1800 mm dolga, približno 650 mm široka in približno 150 mm globoka, 2 para pritrdilnih odprtin po 5 ton v izkopu roke bagra ob straneh vzdolžnega okvirja približno 300 mm od spredaj in približno 200 mm pred zadnjim nagibom 1 skladiščna škatla v poglobljenju tal z pokrovom, Š=720 mm/ D=520 mm / V=170 mm 1. par kolesnih izkopov za poglobitvijo na območju nizkega dna, z naklonom za vožnjo, dolžina spodaj približno 1600 mm, globina približno 400 mm. Opomba! Okvir na glavnem nosilnem območju je 400 mm višji od kolesne izkopa. 2. par kolesnih izkopov med osmi v nizkem dnu na območju voznih stez, z naklonom za vožnjo, dolžina spodaj približno 600 mm, globina približno 300 mm. Opomba! Okvir na glavnem nosilnem območju je 300 mm višji od kolesne izkopa. Ndsdpfx Abei Ri I Ns Dob Pokrov za kolesne izkope, izvlečen iz glavnega okvirja, z lesenimi vložki. Razdalja od glavnega okvirja – nosilec do nosilca zunaj približno 1280 mm Razširitve izvlečne do 3000 mm, pri izlivih kolesnih izkopov zložljive (razširitev ni na zadnjem nagibu in ne na dnu kolesnih izkopov) Prostor za shranjevanje lesenih desk na sredini nakladalne površine ali pod nakladalno površino glede na tehnične možnosti Lesene deske 70 mm za razširitev na 3000 mm Pritrdilne točke nizkonosilca 1 par rin-pritrdišč spredaj v poglobitvi, vsaka za 5 ton 8 parov pritrdilnih gumbov zgoraj in ob straneh v zunanjem okvirju, vsaka za 10 ton 2 x spredaj v poglobitvi 6 x v nizkem dnu; prva pritrdilna točka 250 mm od spredaj in zadnja največ 250 mm od zadaj, razdalja med pritrdišči največ 1100 mm 5 parov obročastih pritrdilnih točk v zunanjem okvirju, vsaka za 5 ton (lahko se spremeni v žepe za kole) Priključek za prikolico – vrtljiva plošča Vlečna ojnička s preizkušenim vlečnim obročem 50 mm, z 8° nagnjenim vlečnim obročem Osovine in vzmetenje SAF bobnaste zavorne osi Z laserjem izmerjeno podvozje – za zmanjšanje obrabe pnevmatik in porabe goriva Zračno vzmetenje s funkcijo dviga in spuščanja, ločeno za spredaj in zadaj Kolesa in pnevmatike 235/75R17,5 po izbiri proizvajalca Jekleni platišči v dvojni izvedbi, tovarniško srebrni Zavorni sistem Dvovodna zračna zavora Vzmetno zadržana parkirna zavora Infocenter prikolice za prikaz podatkov o vozilu kot so osni tlak (ni overjene tehtnice) in števec kilometrov Prepoznavanje osnega tlaka preko signala EBS-Canbus, za prikaz na zaslonu v kabini, tovornjak mora biti ustrezno pripravljen, nobena instalacija na tovornjaku (ni overjene tehtnice) Stabilnostni sistem za vozila Duomatic priključek spredaj, z povezovalnim kablom na vlečno vozilo EBS, elektronski zavorni sistem z EBS priključkom spredaj in povezovalnim kablom Pozor: Priklopno vozilo se sme vleči le z vlečnimi vozili, ki zagotavljajo delovanje ABS! Elektrika 24 voltov, večkomorni LED luči z uporom, stranske rumene LED signalizacije, LED osvetlitev registrskih tablic, 2 bele pozicijske LED luči spredaj 2 belo/rdeči LED smerni lučki zadaj Dodatni LED delovni žaromet, zadaj, upravljan prek vzvratne luči 1 x 15-polni vtikač spredaj

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: Produktpalette, lastna masa: 12.800 kg, največja dovoljena obremenitev: 44.200 kg, skupna masa: 57.000 kg, konfiguracija osi: > 3 osi, vzmetenje: zrak, velikost pnevmatike: 235/75 R17,5", stanje pnevmatik: 100 odstotek, Rešitev transporta po meri Konfigurirajte svoje vozilo Fliegl v skladu z vašimi zahtevami. Prikazano vozilo je primer. Proizvodnja in oprema sta prilagojeni posameznim željam kupca. Podvozje: polpriklopnik z nizkim ležiščem Jeklena varjena konstrukcija, sedlasta plošča z zamenljivim drugim zatičem kralja in dvema pozicijama za drugi zatič 24 t dvostopenjski podporni vitel, enostransko upravljanje Zložljiva zadnja opora 2 zagozdi za podvozje s pritrdilcem Stranska zaščita proti naletu iz aluminija 1 plastična orodjarna s polico, b =620/h =360/t =440 mm, z možnostjo zaklepanja s ključavnico Razširitve izvlečne do 3.000 mm Predal za lesene deske na labodjem vratu, spredaj prečno Lesene deske 70 mm za razširitev na 3.000 mm Teleskopski sistem Centralni cevni okvir iz natančno zvarjenih, teleskopsko prekrivajočih se delov okvirja izvlečno do maks. 6.000 mm in z možnostjo fiksacije na vsakih 1.000 mm Zavarovanje s pomočjo mehanskega zatičnega sistema s pomično mizo Pritrdilne ušice za nizkopodna vozila 2 para obročastih priveznih ušes, po 5 t, spredaj na labodjem vratu, 11 parov priveznih nastavkov zgoraj in ob strani v zunanjem okviru, vsak po 10 t, 2x na labodjem vratu, 9x na površini nizkega ležišča, prva privezna točka 250 mm od spredaj in zadnja največ 250 mm od zadaj, razdalja med ušesi ne več kot 1.100 mm 8 parov žepov za kolike, vdelanih v zunanji okvir, notranja mera 70 x 40 mm (prilagodljivi za 5 t obročasta ušesa, ni vključeno v dobavo) 3 para zložljivih priveznih ušes, dodatno vgrajenih v območju nizkega ležišča, vsak po 10 t: 1x začetek nizkega ležišča, 1x pred 1. osjo in 1x za 3. osjo Ndjdpfxsi Ri Hnj Ab Deb Preme in vzmetenje SAF bobnaste zavore Premične/šasija lasersko merjena za zmanjšanje obrabe pnevmatik in porabe goriva Zadnji dve premi vodeni, z avtomatsko blokado vzvratne vožnje prek vzvratnih luči in ročno blokado z gumbom na vozilu Zračno vzmetenje z ventilom za dvig/spust Kolesa in pnevmatike 235/75 R 17,5, znamka Fulda Jeklena platišča v dvojni postavitvi, tovarniško srebrna Zavorni sistem Dvovodni zračni zavorni sistem Vzmetna parkirna zavora Sistem stabilnosti vozila Prikaz nosilnosti osi preko EBS-Canbus signala, za prikaz na zaslonu v kabini tovornjaka, tovornjak mora biti temu prilagojen, brez LKW instalacije (brez overjene tehtnice) 2 proti zamenjavi odporna priključna spoja spredaj, brez povezovalnih cevi EBS, elektronski zavorni sistem z EBS vtičnico spredaj, brez povezovalnega kabla Opozorilo: Priklopno vozilo lahko vlečejo le vlečna vozila, ki zagotavljajo delovanje ABS! Elektrika 24 V, večkomorni žarometi, stransko rumena LED osvetlitev 2 bela pozicijska žarometa spredaj 2 bela/rdeča označevalna žarometa zadaj 1 LED rotacijska luč z nosilcem, upravljana prek pozicijskih luči (luč snemljiva) 2 para opozorilnih plošč, dvojno LED osvetljene in izvlečne do 3.000 mm 2x 7-polni proti zamenjavi odporni vtičnici spredaj, brez povezovalnega kabla Talna obloga Labodji vrat s prevleko iz jekla/protizdrsne pločevine Skladiščni prostor v naklonu labodjega vratu nato z 70 mm mehkim lesenim podom, v območju kolesnih vodil jekleni/protizdrsni sloj Zadnji naklon s 70 mm mehkim lesenim podom Stranske stene 25 mm aluminijasti votli profil, 400 mm visoke, spredaj in ob strani na labodjem vratu, snemljive Nakladalne rampe Jeklene rampe, dolžine 2.800 mm, širine 750 mm, bočno pomične prevlečene z lesom Hidravlično prek priklopa na pomožni pogon vlačilca z dušilnikom Hidravlični priključek s SVK spojko NW 10/3, brez povezovalnih cevi Navodila za upora