Nizkopodnožni polpriklopnik nakup rabljenega (446)

Stanje: novo, lastna masa: 9.800 kg, največja dovoljena obremenitev: 39.200 kg, skupna masa: 49.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 9.800 kg, Oprema: ABS, Chassis: - Robust welded steel frame construction with a front frame dip and flat loading platform featuring a rear bevel approx. 500x100 mm - Frame neck 200 mm with chamfered corners at the front - Sloped swan neck end approx. 500 x 100 mm (with anti-slip profile strips on outer frame in the area behind the rear bevel) - 2 king pin positions with replaceable 2” king pin - Outer frame closed to the outside and designed as perforated outer frame - Loading platform with extendable central frame, extendable by around 2,000 mm, lockable in 500 mm increments pneumatically - Frame with 80x80 mm step at and after extension joint - Reinforced frame design / maximum point load when retracted at center of gravity - Without extendible load platform outriggers, but pre-fabricated to allow retrofit (= guide tubes welded in frame) - With excavator trough (no cover), approx. 220 mm deep, 600 mm wide, starting behind 2nd axle to vehicle end - 1 pair of wheel wells between 1st and 2nd axles, covered with steel plates (covers with Körapur coating), approx. 400 mm deep - Rear underrun protection = extended rear plate - Drop-down supports at the rear Ramps: - 2 two-piece loading ramps, special design with mechanical extension - Length approx. 2,850 mm plus 1,850 mm, with hydraulic ramp lifting device (only with electro-hydraulic unit) - Width approx. 800 mm - Wooden surfacing - Including anti-slip strips on ramps - Can be locked in transport position with tie-down straps - Operated by control lever mounted on rear right in frame - Hydraulically laterally adjustable Floor: - 35 mm larch wood floor with aluminium omega profiles Bdodpfxoxgm S Dj Abmjk Landing legs: - Mechanical 24-ton landing legs with single-sided operation and compensating device Axles, steering and tires: - BPW air suspension axles, each with 10-ton axle load, air bellows diameter 360 mm - S-cam brakes 300/200 mm, asbestos-free brake linings - Automatic slack adjusters - Lifting and lowering system with total lift approx. 200 mm - 2nd driving position via ball valve +50 mm - 1st axle lift axle (wired through EBS), automatic control, with manual override button on the trailer - 3rd axle as friction-steered trailing axle with electric and mechanical lock - 12 steel disc wheels, 10-hole, center offset by center bore - 12 tires, 245/70 R 17.5 143/141J, tubeless - Including tire pressure monitoring system Accessories: - Insertable side and rear stakeboards on the swan neck, approx. 400 mm high - Spare wheel carrier - Side aluminium underrun protection - 4 chocks - 1 plug-in ECE rear warning board - 11 pairs of ZK modules 10t, lateral: - 2x on the swan neck - 2x on loading area before extension - 7x after extension - Extendable warning signs including 3 position lamps each, at the front on landing legs and rear before the rear plate, steplessly extendable up to 4,500 mm loading width - 4 plug-in sockets for warning signs in stake pockets on the loading platform - 6 pairs of stake pockets laterally for 100x50 mm stakes - 2 cross rows stake pockets for 100x50 mm stakes on swan neck, from outer frame to main frame (1x before/1x after king pin positions) - 3 cross rows stake pockets for 100x50 mm stakes on loading area from outer frame to main frame (1x before the extension, 1x after extension, 1x after the 3rd axle) - 2 pairs of steel plates in the loading platform for container locks to accommodate 1x 20ft container - Rubber apron mounted on underrun protection

Stanje: rabljeno, lastna masa: 14.995 kg, največja dovoljena obremenitev: 50.805 kg, skupna masa: 65.800 kg, konfiguracija osi: 3 osi, prva registracija: 10/2023, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, barva: siv, Leto izdelave: 2023, obratovalna teža: 14.995 kg, Oprema: ABS, For every used semi-trailer, you will receive a current and comprehensive inspection and functionality report. Gooseneck: - Gooseneck with rear bevel, approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading platform: - Extendable loading platform with rear bevel, approx. 500 mm x 8° - 6 pairs of fold-out lashing rings to the outside (LC 5,000 daN) - 4 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) - 1 intermediate section, 250 mm - Cut-outs in the outer frame of the loading area for inserting tensioning straps (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, chequer plate over the axles Axles and tyres: - BPW axles with hydro-mechanical forced steering - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - Axle tools - Tyres 235/75 R17.5 Braking system: - Braking system according to EU regulations with EBS-E (4S3M) Bdjdpjv Hr Axjfx Abmok Accessories included: - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings mounted on the galvanized connection strip at the front - 4 chocks with holders on the front wall - One spare wheel with holder in front of the front wall - Electro-hydraulic power unit - Remote steering from front and rear via cable remote control with push buttons, including single-track control of the axles - Mounting for ALU ramps at the rear of the gooseneck - Hot-dip galvanized, extendable side extensions, approx. 230 mm per side - European reflector boards (red-yellow) at the rear of the trailer - White reflective tape as per EU standards on the sides, on the extension, and red at the rear - Bracket for warning signs on left/right of gooseneck and rear panel, incl. socket - Galvanized folding supports under the loading platform’s rear bevel - Holder for a beacon at the rear of the trailer - Central lubrication system with 2 BEKAMAX (Pico) pumps, NLGI-2 standard grease and removable cover for the pump - Mud flap at the rear of the trailer - Manual and documentation - On the gooseneck: insertable ALU side boards and rear wall, approx. 2,440 x 400 mm - Removable galvanized stanchions at the rear (body length approx. 2,560 mm) - 4 pairs of WADER container locks recessed in the loading platform for 1x 20ft, 2x 20ft, 1x 40ft, or 1x 45ft container - 8 pairs of pockets for removable stanchions, 100 x 50 mm, in the outer frame of the loading platform - Adjustable hook rails for ALU ramps at the rear of the vehicle - Lift axle on the front axle, controlled by TEBS E depending on current axle load and loading condition - Four warning panels, extendable approx. 400 mm, approx. 423 x 423 mm, each with position lamp - Mounting on warning panels for beacon - Radio remote control for remote steering in addition to cable remote control, with indicator lights on the receiver for single-track control - Painted-in sand layer on chequer plates, above the king pin and on the loading area for anti-slip protection - 80 km/h speed limit decal at the rear - Load pressure gauge for axle load determination, including load chart

Stanje: novo, lastna masa: 15.550 kg, največja dovoljena obremenitev: 47.450 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimization of loading platform length, length approx. 3,700 mm - Rear gooseneck with bevel approx. 1,000 mm x 10° Loading Platform: - Extendable loading platform, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° - A recess in the loading platform as well as into the bevel for accommodating the excavator dipper stick - Pneumatic locking with conical locking bolts and reinforced lock positions - Hardwood covering on the loading platform bevel Bsdpek Aht Ujfx Abmedk Ramps: - 1 pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm - Ramps with hardwood covering - Hydraulically folding ramp tips - Ramps can be hydraulically shifted individually approx. 235 mm outward and approx. 215 mm inward - Square climbing cleats 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, 1st axle lift-steered, all other axles forced-steered with hydromechanical system - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with raising and lowering valve - Tyres 235/75 R 17.5, twin tires - TPMS tire monitoring system compliant with ECE R141 - TPMS sensors installed in all wheels including spares Accessories included: - Removable steel front wall, approx. 400 mm high - 3kW electro-hydraulic power pack for hydraulic operations, excluding hydraulic winches - Parking position on gooseneck for warning boards when not in use - 1 spare wheel - On the gooseneck: 1 pair of removable side aluminium drop sides, approx. 400 mm high, anodised - On the gooseneck: 1 removable rear aluminium drop side, approx. 400 mm high, anodised - Above the gooseneck: approx. 40 mm thick hardwood floor, chequer plate above king pin - 2" king pin - Guide plate on gooseneck for fifth wheel, approx. 500 mm wide - 4 wheel chocks - Mechanical landing gear with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - 1 intermediate table, approx. 300 mm wide - Extensions (galvanised) extendable by approx. 230 mm per side - Wheel recesses with square climbing cleats - ALU covers for the wheel recesses - 1 pair of mechanical rear supports - Remote steering at front and rear via cable remote control, with single track monitoring of axles - 1st axle with automatic lift axle function - Central lubrication system with 1 BEKAMAX brand pump - Radio remote control for remote steering, additionally to cable remote, with 2 indicator lights on the receiver as single track monitoring - Wabco Smart Board System - 4 warning boards, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for revolving beacon

Stanje: novo, lastna masa: 10.700 kg, največja dovoljena obremenitev: 38.800 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17,5, barva: sivo-črna, Oprema: ABS, Gooseneck: • Gooseneck with front corners beveled at 45° and rear taper approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Extendable loading platform: • Loading platform in extendable design with rear taper approx. 1,000 mm x 8° • Cut-outs in outer frame of loading platform for attaching tensioning straps • Approx. 48 mm thick hardwood flooring; anti-slip checker plate covering above the axles Two-piece steel ramps: • One pair of galvanized, two-piece steel ramps with approx. 48 mm thick hardwood covering • Ramps with hydraulically foldable ramp sections, hydraulic lift system, and hydraulically adjustable • Maximum load per pair: approx. 40,000 kg Axles and tires: • BPW axles and suspension, 2 rigid axles, 1 self-steering axle • Technical axle load: 12,000 kg • Electromagnetic reverse lock, activated via reverse gear or manually • Air suspension with lift and lower valve • Axle tools • 235/75 R 17.5 3PMSF Braking system: Bdodpfx Abehlz S Njmek • WABCO braking system according to EU regulations with EBS-E Paintwork: • First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component zinc dust primer • High-quality, single-color top coat in MB 7350 Novagrey applied with two-component paint • Rear section metallized and painted in RAL 9010 Landing legs: • JOST landing legs with 2-speed gearbox for 24t lifting load (50t test load) Steel construction: • Steel construction made of high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC • S690QL/S700MC Electrical system: • Electrical system in accordance with EU regulations, 24 Volt lighting • ASPÖCK-UNIBOX on front connection panel with 24N, 24S & 15-pin sockets Accessories included: • One spare wheel with holder • Galvanized steel front wall approx. 400 mm high • Yellow-red air couplings on the galvanized front connection panel • 4 wheel chocks • Rear mounting bracket for beacon light at the end of the semitrailer • Recess at rear of gooseneck for ALU approach ramps • Galvanized folding supports under the loading platform taper • Cover plates to bridge the gap between ramps and loading platform • White reflector tape per EU regulations on sides, extension, and red at rear • Electro-hydraulic unit at rear, under the loading platform • On gooseneck and ramps, left and right, each with a holder for warning signs, including socket • Operating valves for the ramps located on the right side of the trailer • ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) • Four warning panels extendable by approx. 400 mm with a position light • 3 pairs of WADER container pockets in the loading platform for one 20ft, 30ft or 40ft container • 6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading platform • Galvanized extensions, extendable by approx. 230 mm per side • 20 x 20 mm square climbing strips every 200 mm on the outer frame of the platform taper • Painted anti-slip sand layer on checker plates, above king pin and loading platform • Load gauge for axle load measurement, including load diagram • HRM metallization (High Resistance Metallisation) of the outer frame • Complete steel construction shot-blasted, then defined visible surfaces metallized and hot-finished with ZINACOR 850 (Zinc 85% - Alu 15%)

Stanje: rabljeno, lastna masa: 10.200 kg, največja dovoljena obremenitev: 37.800 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 09/2023, dolžina tovornega prostora: 9.400 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, velikost pnevmatike: 235/75 R 17.5, barva: siv, Leto izdelave: 2023, obratovalna teža: 10.200 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the usable deck length, approx. length 3,700 mm - Rear of gooseneck bevelled approx. 1,000 mm x 6° - Technical fifth wheel load: 18,000 kg - For tractor units: 4 x 2 or 6 x 2 Load Area: - Load deck, approx. length 9,400 mm, with rear bevel of approx. 900 mm x 6° - Load area after the gooseneck, hydraulically liftable and lowerable - Deck length approx. 3,000 mm. Load capacity up to approx. 9,000 kg Ramps: - One pair of two-piece steel ramps, approx. 4,350 x 900 mm - Hardwood covering - Hydraulically foldable ramp tips - Ramps can be hydraulically shifted individually approx. 235 mm outwards and 365 mm inwards Axles, Suspension, and Tyres: - BPW axles and suspension, two rigid axles, one self-tracking axle - Technical axle load: 12,000 kg - Air suspension with lifting and lowering valve - Tyres 235/75 R 17.5 Standard Equipment Included: - Plug-in steel front wall, approx. 400 mm high - Round NATO socket at the front connection bar (Maeler & Kaege VG 96 917) - 3 kW electro-hydraulic power unit for hydraulic functions (excluding hydraulic winches) - Outer beam of gooseneck with fastening holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included (LC 5,000 daN) Bodpfowx E Hmsx Abmsdk - One mounting hole in the upper rear area of the gooseneck outer beam for a bolted lashing ring - 1 pair of screw-in lashing rings included (LC 10,000 daN) - 3 pairs of recessed lashing rings inside outer beam of gooseneck (LC 5,000 daN) - 3 pairs of lashing rings in the center of the gooseneck (LC 5,000 daN) - 1 pair of recessed lashing rings at the rear center of the gooseneck (LC 5,000 daN) - On the gooseneck: 1 pair of plug-in anodised aluminium side boards, approx. 400 mm high - On the gooseneck: one plug-in anodised aluminium rear board, approx. 400 mm high - Over gooseneck: approx. 40 mm hardwood covering - 2'' king pin - Guide plate of gooseneck for fifth wheel, approx. 500 mm wide - 4 wheel chocks - Mechanical landing legs with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - On the lifting bed: continuous hardwood floor approx. 50 mm thick, interrupted between the axles - 9 pairs of recessed, foldable lashing rings in the outer frame of the load deck (LC 10,000 daN) - 3 pairs in the lifting bed outer frame and 6 pairs in the load deck outer frame - 1 pair of folding mechanical rear stabilizers, single-lever operation - Central lubrication system with one pump, BEKAMAX brand, with standard grease per NLGI-2 - Hardwood covering on the sloped section of the deck - 2 additional pairs of bolted lashing rings (LC 5,000 daN) - Electric cable winch, approx. 5,400 kg pulling force, with radio remote control. Steel cable approx. 24 m long, cable Ø approx. 9.5 mm, incl. cable pressure roller - 1 spare wheel with mounting adapter under the load deck, right side before the axles - 9 pairs of recessed lashing rings along the central beam (LC 5,000 daN) - 3 pairs in the lifting bed and 6 pairs in the rear section of the deck - 1 stainless steel toolbox, approx. 620 x 300 /180 x 950 mm, left and right under the load deck - WABCO Smart Board System - 1st axle with starting aid - 1 reversing spotlight each left and right at the rear of the vehicle - 4 extendable warning boards, approx. 423 x 423 mm, extendable by approx. 400 mm, including 2 position lights and mounts for rotating beacon

Stanje: novo, lastna masa: 8.950 kg, največja dovoljena obremenitev: 40.050 kg, skupna masa: 49.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.550 mm, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 8.950 kg, Oprema: ABS, Chassis: - Robust welded steel frame construction with front frame cranking and flat loading area with rear taper approx. 500x100 mm - Neck of frame 200 mm with beveled corners - Tapered end of gooseneck approx. 500 x 100 mm (traction ribs on outer frame in area behind rear taper) - 2 king pin positions with replaceable 2" king pin - Outer frame closed outside as perforated outer frame for lashing with tie-down straps Bsdpfx Aowu Agiebmjdk - Reinforced frame design / point load at center of gravity - Prepared for extendable width extensions in the loading area - With excavator trough, depth approx. 220 mm, width approx. 600 mm, starting after the 2nd axle to end of vehicle - 1 pair of wheel recesses in front of axle with steel covers - (Covers with Körapur coating), depth approx. 400 mm and 1 pair of wheel recesses between 1st and 2nd axle with steel covers - Underrun protection = extended end plate - Drop-leg supports at rear Ramps: - 2 pieces, single-part aluminium loading ramps with spring lift system - Dimensions (L x W) approx. 2,500 mm x 600 mm - Can be locked in transport position with tie-down straps - Laterally adjustable by hand Floor: - 35 mm larch wood floor with aluminium omega-profiles Landing Gear: - Mechanical 24 t landing gears with single-sided operation and load compensation Axles, Steering, and Tyres: - BPW air suspension axles, 10 t axle load each, air spring diameter 360 mm - S-cam brakes 300/200 mm, asbestos-free brake linings - Automatic slack adjusters - Lift/lowering device with total travel approx. 200 mm - 2nd driving position via ball valve +50mm - 1st axle lift axle (wired via EBS), fully automatic confirmation with mechanical emergency operation by push button on trailer - 3rd axle is friction-steered trailing axle with electric and mechanical lock - 12 steel disc wheels, 10-hole, hub-centered - 12 tyres 245/70 R 17.5 143/141J, tubeless - Incl. tyre pressure monitoring Brake System: - Two-line brake system with EBS-E including RSS - EBS (WABCO 4S3M) - Spring-loaded parking brake - Air connections yellow / red Paintwork: - Steel shot-blasting, chassis spray galvanising and priming - Chassis / wheel hub / outer frame painted in DB 7350 Novagrau - Plastic parts black, unpainted - Rims: factory silver - Reflective strips on sides and rear in yellow Accessories: - Removable side and rear walls approx. 400 mm high on gooseneck - Spare wheel bracket - Aluminium bump guard - 4 wheel chocks - Sheet metal mudguards with Clear-Pass - Long licence plate holder in end plate - 1 removable ECE board at rear - 11 pairs ZK modules 10 t at sides: - 2x on gooseneck - 9x on loading area - Without tow rings at rear - Extendable warning boards incl. 3 position lights each, front at landing gears and rear before end plate, infinitely extendable to loading width 4,500 mm - 4 mounting holders for warning boards plug-in type in stake pockets on loading area - 6 pairs of stake pockets at sides for 100x50 mm plug-in stakes - 2 rows transversely on gooseneck for 100x50 mm plug-in stakes from outer frame to main frame (1x before and 1x after king pin positions) - 3 rows transversely on loading area for 100x50 mm plug-in stakes from outer frame to main frame (1x front section, 1x before 1st axle, 1x after 3rd axle) - 2 pairs of steel plates in loading area for container locks, suitable for 1x 20ft container - Rubber apron fitted on underrun protection

Stanje: novo, lastna masa: 11.000 kg, največja dovoljena obremenitev: 38.500 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Loading area: - Telescopic loading area with rear incline approx. 1,000 mm x 8° - 1 pair of permanently integrated wheel wells in front of the axles, approx. 2,850 x 970 x 400 mm - Wheel wells with 15 x 15 mm square climbing strips and lower width extensions - Between the 1st and 2nd axle, one pair of fixed wheel wells with cover, approx. 1,610 x 970 x 400 mm - Recess in both the incline and extending into the loading area for receiving the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of outward-folding lashing rings (LC 5,000 daN) - 2 pairs of outward-folding lashing rings (LC 10,000 daN) - Cutouts in the outer frame of the loading area for securing straps. (LC 2,000 daN) - Includes 3-piece removable galvanized covers over the wheel wells – max. point load 3.5 t / piece. Hydraulic Two-piece Steel Ramps: - A pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm with 48 mm thick hardwood overlay - Ramps with hydraulically operated folding sections (up/down), hydraulic lifting system, and hydraulic horizontal adjustment Axles and Tyres: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock barrier activated via reverse gear and manual control - Air suspension with raise/lower valve - Axle tools - Tyres 235/75 R 17.5 Bdodpfx Abeup U Hzsmok Accessories included: - 2" kingpin - One galvanized steel front wall approx. 400 mm high - One spare wheel with holder mounted in front of the front wall - Yellow-red air couplings on the galvanized connector strip at the front - 4 wheel chocks with holders on the front wall - Rear gooseneck receiver for ALU approach ramps - Galvanised, extendable width extensions, approx. 230 mm per side - Galvanized folding supports under rear incline of the loading area - Rear mounting bracket for rotating beacon at the trailer rear - White reflective tape as per EU regulations on sides, on extension, and rear (red) - Mounts for warning panels on both sides of the gooseneck and rear panel, incl. socket - One mudflap at the trailer rear - European reflective plates (red-yellow) at trailer rear - On the gooseneck, ALU plug-in side and rear walls approx. 2,440 x 400 mm - Rear galvanized removable stanchions (body length approx. 2,560 mm) - 2 pairs WADER container locks in the loading area for one 20 ft or 30 ft container - 3 pairs of stake pockets for plug-in stanchions 100 x 50 mm in loading area outer frame - Removable galvanized intermediate table with 1 pair WADER container locks - Square climbing strips 20 x 20 mm spaced every 200 mm on outer frame of loading area incline - Four extendable warning signs approx. 423 x 423 mm with position light, extendable by approx. 400 mm - Mounting for rotating beacon on warning panels - 80 km/h speed stickers at rear and on both sides - Load gauge for axle load determination including load chart - HRM metallization (High Resistance Metallization) of the outer frame - Complete steel structure shot-blasted, then all defined visible surfaces metallized with ZINACOR 850 (Zinc 85% - Alu 15%) using hot finishing Available as an option: - Tool box on the gooseneck

Stanje: pripravljen za uporabo (rabljen), lastna masa: 13.900 kg, največja dovoljena obremenitev: 33.100 kg, skupna masa: 47.000 kg, konfiguracija osi: 2 osi, prva registracija: 01/2023, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 350 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Leto izdelave: 2023, obratovalna teža: 13.900 kg, Oprema: ABS, For every used semi-trailer, you will receive a current and complete inspection and function report. Gooseneck: - Gooseneck in SNT design for optimal loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractors: 4 x 2, 6 x 2, and 6 x 4 Bedpsw S Tt Hofx Abmjdk Loading platform: - Lowbed with external girders in extendable "SUPER LOW" design, approx. 6,850 mm long - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking - 5 pairs of folding lashing rings on the outside - 6 pairs of threaded blocks on the inner girder for mounting bolt-on RUD rings Rear running gear: - Rear running gear with closed outer frame, chequer plate deck, and continuous prismatic excavator recess approx. 1,250/700 x 505 mm, open at the rear Pendulum axle and tyres: - "PENDEL-AXLE", all axles hydromechanically forced-steered - Burst protection valve on axle leveling cylinders with automatic RESET function - Hydraulic cylinders with shut-off valves and plug-in pins for securing in lifted position - Axles finished with 2 coats of single-colour 2K paint in grey - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 Accessories included: - Prepared for bolt-on container lockings for 1x 20ft or 1x40ft container on the outer beams - 2" kingpin - One galvanized steel headboard approx. 400 mm high - One spare wheel with holder - Front galvanized connection strip with yellow-red air couplings - 4 wheel chocks with holders - Remote cable control for steering both front and rear, with single-track axle alignment control - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Electro-hydraulic power pack - 2 wooden blocks 500x250x200 mm - One bracket for rotating beacon at the rear - One rear mudflap - European reflective boards (red-yellow) at the rear of the trailer - At the gooseneck and rear panel, left and right, each with a bracket for warning signs incl. socket - Central lubrication system with 2 BEKAMAX pumps - Axle load gauge incl. loading diagram - 6 pairs of threaded blocks between the lashing rings under the top flange on the outer beam for mounting bolt-on RUD VLBG-4 rings - 2 pairs of bolted-on container supports on the outer beams, incl. 2 pairs of container locks for 1x20ft or 1x40ft containers - On the gooseneck, removable aluminium drop sides and rear wall approx. 2,440 x 400 mm - One INOX toolbox 1,350 x 400 x 400 mm on the gooseneck - 5 pairs of stake pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading area - Folding extensions, approx. 230 mm each side - Extension boards made of hardwood - Maximum load allowed on a 200 x 200 mm area: 3.5 t - 1 pair of steel ramps for bridging the mounting hooks of the lowbed - Loading surface with painted sand layer as anti-slip coating - 2 reversing lights on the rear panel - Bucket recess in the rear running gear closed front and rear with insertable plates - Four extendable warning signs approx. 423 x 423 mm, extend by approx. 400 mm, with position lamp - HRM metallization (High Resistance Metallisation) of the outer frame

Stanje: novo, lastna masa: 10.900 kg, največja dovoljena obremenitev: 37.100 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 890 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, obratovalna teža: 10.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the loading platform length, approx. 3,700 mm long, rear bevel approx. 1,000 mm x 6° - Technical king pin load: 18,000 kg - For tractor units: 4 x 2 and 6 x 2 Loading platform: - Loading platform, approx. 9,600 mm long with rear taper approx. 900 mm x 6° - Platform area behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, with a load capacity of up to approx. 9,000 kg - Grating surface and steel sheet floor approx. 5 mm thick as additional reinforcement on the sloped section of the platform Ramps: - One pair of two-section AXS steel ramps, approx. 4,675 mm long and approx. 900 mm wide - Grating surface - Hydraulically folding ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 365 mm inward - Painted sand coating on the outer frame and ramp tips - Flashing lights on the outer sides of the ramp tips with control switch next to the ramp operation panel - Ramp lock in transport position with quick-release fastener Axles, suspension and tires: - BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steerable (trailing) - 1st axle with traction assistance - Operated via brake pedal in the tractor unit - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 - TPMS tire pressure sensors installed on all wheels including spare wheels Brake system: - WABCO EBS-E braking system in accordance with EU regulations Paintwork: Bodpouadk Nofx Abmjdk - Trailer MB 7350 Novagrau Equipment included: - Removable front steel wall, approx. 400 mm high - 3 kW electro-hydraulic power unit for hydraulic operations, except for hydraulic winches - Gooseneck guide plate for the fifth wheel, approx. 500 mm wide - JOST Module B – static test load = 50,000 kg - Continuous grating with 5 mm steel underlay as additional reinforcement - Painted sand coating - Cutouts in the outer frame of loading platform and lift bed for hooking hydraulic ramp control valves on the right-hand side of the vehicle - 2" king pin - Central lubrication system with 1 pump, brand BEKAMAX - 1 pair of plug-in ALU side boards on the gooseneck, approx. 400 mm high, anodised - Electric winch, approx. 5,400 kg pulling force, with radio remote control - Steel wire rope approx. 24 m long, rope diameter approx. 9.5 mm, including rope pressure roller - WABCO Smart Board system - 4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, lastna masa: 29.600 kg, največja dovoljena obremenitev: 72.400 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 6.650 mm, širina tovornega prostora: 2.840 mm, višina nakladalnega prostora: 550 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, obratovalna teža: 29.600 kg, Oprema: ABS, Gooseneck: - Gooseneck hydraulically liftable/lowerable and detachable - Length approx. 3,650 mm - For tractor units: 6 x 4 or 8 x 4 2-axle front bogie: - Hook mountings at front and rear - Bogie length x width approx. 2,200 mm x 2,850 mm Excavator deck "BB-A": - Telescopic excavator deck "BB-A" with drive-over bridge hooks at the front and pin-lug coupling at the rear - Length x base width approx. 6,650 mm x 2,850 mm - Beam height x beam width approx. 400 mm x 1,350 mm - Loading height 550 mm with 150 mm ground clearance 4-axle rear bogie: - Mechanical pin-lug coupling for the installation of a lowbed at the front, rear crossmember at the back - Bogie length x width approx. 5,480 mm x 2,850 mm - Multiple lashing points Pendulum axles and tyres (front and rear bogies): - "PENDULUM AXLE", all axles forced-steered via hydromechanics - Hose rupture valve on axle compensation cylinders with automatic RESET function - Hydraulic cylinders with shut-off valves and locking clips for securing in raised position - Final coating on axles: 2 layers of single-colour MB 7350 Novagrau 2K paint - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres size 285/70 R19.5 Remote steering (after-steering): - Remote steering operable from front and rear via cable remote control with pushbuttons, including single-track monitoring for axles - Socket for remote steering control on gooseneck - Cable remote control with pushbuttons and single-track control included Accessories included: - Yellow and red air couplings on the galvanised front connection bar - Steel front wall approx. 400 mm high - 4 wheel chocks - 3.5" king pin - One 7-pin socket left and right at rear of gooseneck for warning boards - Hoisting jib with winch for spare wheel at the front face of the gooseneck - Truck hydraulic connection with flow control (40 l/min), including support jib for supply lines; tractor unit tank must have at least 80 litres capacity with couplings - Plug-in ALU side and rear boards on gooseneck, approx. 400 mm high, anodised - Control lever on gooseneck protected by foldable cover - Separate air connection with air gun on gooseneck - BEKAMAX central lubrication system: 1x on gooseneck, 1x on 2-axle and 1x on 4-axle bogie - Variomax tool kit - Multi-coupling hydraulic connectors on gooseneck and at lowbed hook interface - 2 spare wheels - One 7-pin socket left and right, at front and rear of rear bogie for warning boards - Front bogie with separate air connection for impact wrench Bsdpfxewcmhaj Abmodk - Foldable steel bed extensions, adjustable in width from approx. 2,850 mm to 3,250 mm - Steel bed inserts can be placed in 2 positions for sunken load area - Steel mats with rubber flooring, approx. 12 mm thick - Thread-in options (⌀ 40 mm) every approx. 500 mm on the upper flange of the excavator deck outer tube for eye bolts - One locking point at every approx. 500 mm on extension with mechanical lock - Socket on rear bogie for remote steering cable control - 2 reversing lights on rear panel - Four extendable warning boards (by approx. 2,000 mm), each approx. 423 x 423 mm with position lights - 1 work light left + right on rear panel of gooseneck with separate on/off switches - Two INOX toolboxes, approx. 855 x 340 x 390 mm - 1-cylinder Hatz diesel engine (Silent Pack) - Radio remote control for after-steering

Stanje: novo, lastna masa: 10.300 kg, največja dovoljena obremenitev: 39.200 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Platform: - Loading platform after the gooseneck, hydraulically liftable and lowerable, length approx. 2,800 mm, with rear chamfer approx. 1,000 mm x 8° - Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, over the axles with chequer plate covering Two-part Steel Ramps: Bdedpfx Abeu Hp Hremek - One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp parts, hydraulic lifting system, and hydraulically adjustable - Maximum load per pair: 40,000 kg Axles, Suspension and Tires: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated by reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tires 235/75 R 17.5 3PMSF - TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories Included: - One spare wheel with holder in front of the bulkhead - 2" kingpin - One galvanized steel front wall approx. 400 mm high - Yellow-red air couplings at the galvanized connection strip in front - 4 wheel chocks - Galvanized folding supports under the platform's rear chamfer - A holder for a rotating beacon at the rear of the trailer - Cover plates to bridge the gap between ramps and platform - White reflective tape as per EU regulations along the sides of the trailer and red at the rear - Electro-hydraulic unit at the rear, under the platform - At the gooseneck and at the ramps left and right, each with a holder for warning signs, including socket - Control valves for the ramps positioned on the right side of the trailer - European reflective plates (red-yellow) at the rear of the trailer - Manual and description on USB stick - Removable ALU side walls and rear wall on the gooseneck approx. 2,440 x 400 mm - The rear, galvanized side stakes are removable (body length approx. 2,560 mm) - An electric cable winch with radio remote control, approx. 5,400 kg lifting force, including 9.5 mm steel cable, 24 m long, with guide roller - Bolted 5 t ring for cable deflection of the winch on the gooseneck without pulley - 2 pairs WADER container pockets in the platform for a 20ft container - 6 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the platform - Lift axle on the front axle with control via TEBS E, depending on actual axle load and loading condition - 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN) - 1 pair of recessed lashing rings along the central beam at the rear chamfer (LC 10,000 daN) - Sand coating for slip resistance painted on the chequer plates on the gooseneck and on the platform - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and removable pump protection - Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm - Speed stickers 80 km/h rear and on both sides - Load manometer for determining axle loads including load chart - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then all defined visible surfaces metallized and hot-coated with ZINACOR 850 (zinc 85% - alu 15%)

Stanje: novo, lastna masa: 13.500 kg, največja dovoljena obremenitev: 51.500 kg, skupna masa: 69.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimizing loading platform length, length approx. 3,700 mm Gooseneck rear with chamfering approx. 1,000 mm x 10° Loading Platform: Telescopic loading platform, length approx. 8,800 mm, with rear chamfering approx. 500 mm x 10° Recess in the chamfer as well as into the loading platform to accommodate the excavator dipper stick Pneumatic locking with conical pin and reinforced locking positions Supply lines routed protected within the extendable beam, adapting to the respective platform length Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps individually adjustable hydraulically approx. 235 mm to the outside and approx. 215 mm to the inside Axles and Suspension: BPW axles and suspension, two rigid axles, two steering trailing axles Electromagnetic reverse lock, activated via reverse gear and manually Air suspension with lift and lower valve Axle tool Tyres: 235/75 R17.5 3PMSF twin tyres Load index: 143/141J (144/144F) Brake System: WABCO braking system, EBS-E in accordance with EU regulations Lighting System: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Metalizing: Standard HRM metallization of the outer frame Complete steel structure shot-blasted, then visible defined surfaces metallized with ZINACOR 850 (Zinc 85% - Alu 15%) hot-refined Steel Construction: Steel grades: Bodpfjk Ahugox Abmsdk S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified as per DIN-EN 287-1 MAG welding process according to EN ISO 4063 Shielding gas M21 as per EN ISO 14175 Accessories Included: Front wall made of steel, plug-in, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin 24N connection per ISO-11852, 24S connection per ISO-3731, 15-pin connection per ISO-12098 Round NATO socket on the front connection strip Cable to supply electro-hydraulic unit and/or electric winch (35 mm², 3.5 m long) between trailer and tractor with connector (NATO-NATO) 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches 1 spare wheel with mounting adapter Outer beam of the gooseneck with fastening holes for screwable lashing rings. The first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included One fastening hole in the rear upper area of the gooseneck's outer beam for a screwable lashing ring 1 pair of screw-in lashing rings Approx. 40 mm thick hardwood covering above the gooseneck On the gooseneck, 1 pair of plug-in side aluminium walls, approx. 400 mm high, anodized On the gooseneck, a plug-in aluminium rear wall, approx. 400 mm high, anodized 2" kingpin Gooseneck guide plate for fifth wheel, approx. 500 mm wide 4 wheel chocks with holder Holder for aluminium approach ramps Mechanical landing gear with 2-speed gearbox and crank Continuous hardwood floor approx. 50 mm thick on the loading platform, interrupted between axles Platform locking with conically welded locking profiles every 250 mm incl. tension plate Slotted holes at the front of the loading platform for attachable and adjustable bridging elements 1 intermediate table with recessed platform, approx. 300 mm wide for the draw-out tube with large cross-section, with sheet metal covering Front and rear with slotted holes

Stanje: novo, lastna masa: 14.800 kg, največja dovoljena obremenitev: 61.700 kg, skupna masa: 76.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck with rear chamfer of approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Loading Platform: • Extendable loading platform with rear chamfer of approx. 500 mm x 8° • 9 pairs of folding external lashing rings • 1 pair of recessed lashing rings at the front of the loading platform • Cutouts in the outer frame of the loading platform for attaching tension belts • Approx. 48 mm thick hardwood flooring, checker plate above the axles Landing Legs: • JOST mechanically operated landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: • BPW axles and suspension, 1st axle steering, 2nd and 3rd axle fixed, 4th and 5th axle follow-steering • Technical axle load: 12,000 kg • 1st, 4th, and 5th axles with electromagnetic reverse lock, activated via reverse gear or manually • Tyres: 235/75 R 17.5 3PMSF Brake System: • WABCO brake system in accordance with EU regulations including EBS-E (4S3M) Paintwork: • Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer • High-quality single-color two-component (2K) topcoat in MB 7350 Novagrau • Rear section metallized and painted in RAL 9010 (Pure White) Steel Construction: • Steel structure made from high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC (yield strength 355MPa) • S690QL/S700MC (yield strength 690MPa) Accessories: • One spare wheel with holder in front of the front wall • 2" king pin • Galvanized steel front wall, approx. 400 mm high • Front galvanized connection strip with yellow-red air couplings • 2 wheel chocks with holders mounted on the front wall • Rear mount on gooseneck for ALU drive-on ramps • Galvanized extendable wideners appx. 230 mm per side • Bracket for a beacon at the rear of the trailer • Galvanized supports under the chamfer of the loading platform • White reflector tape on the sides as per EU regulations, red at the extension and rear • Mounts for warning panels including socket left and right at the gooseneck and rear panel • Detachable ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • Rear galvanized plug-in stanchions removable (body length approx. 2,560 mm) • 3 pairs of WADER container pockets in the loading platform for a 20ft (30ft) or a 40ft container • 7 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform • Lifting axle on the front axle with TEBS E control according to the current axle load and loading condition • Movable mounting rails for ALU drive-on ramps at the rear of the vehicle • 20 x 20 mm square climbing strips at 200 mm intervals on the outer frame chamfer of the loading platform • BEKAMAX (Pico) centralized lubrication system with NLGI-2 standard grease and removable pump cover • Four extendable warning panels approx. 423 x 423 mm with a position light, extendable by approx. 400 mm • Holder for beacon mounted on the warning panels Bsdpfjma Hf Rex Abmodk • European reflector plates (red-yellow) on the rear of the trailer • 80 km/h speed limit stickers at rear and both sides • Axle load gauge with load diagram included • HRM Metallisation (High Resistance Metallisation) of the outer frame • Complete steel structure is shot-blasted, then defined visible surfaces are metallized with ZINACOR 850 (zinc 85% - aluminum 15%) using hot finishing

Stanje: novo, lastna masa: 10.350 kg, največja dovoljena obremenitev: 39.150 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Loading area: - Telescopic loading area with rear chamfer approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm - Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom - Between the 1st and 2nd axle, 1 pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm - 3-piece detachable galvanized covers over the wheel recesses (W 670 mm) – max. point load 5 t / pc. - Recess in the chamfer and protruding into the loading area for the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of foldable external lashing rings (LC 5,000 daN) - 2 pairs of foldable external lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) - Cutouts in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) One-piece aluminum ramps: - 1 pair one-piece ALU ramps, approx. 2,500 x 600 mm - Ramp with spring lifting mechanism and manually adjustable - Maximum load per pair: 24,000 kg Axles and tires: - BPW axles and suspension, 2 rigid axles, 1 trailing steering axle - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tyres 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 Accessories included: - 1 spare wheel with holder in front of the bulkhead - 2" kingpin - 1 galvanized steel front wall approx. 400 mm high - At the galvanized coupling rail at the front, yellow-red air couplings - 4 wheel chocks with holder at the bulkhead - Mounting point at the rear of the gooseneck for ALU ramps - Galvanized extensions, extendable by approx. 230 mm per side - Galvanized folding supports under the chamfer of the loading area - 1 holder for a rotating beacon at the rear of the trailer - White reflective tape laterally, at the extension, and red at the rear, per EU regulations Bodpsiu Er Ajfx Abmjdk - At the gooseneck and rear panel, left and right, each with a holder for warning signs including socket - On the gooseneck, plug-in ALU sideboards and rear wall, approx. 2,440 x 400 mm - The rear galvanized stakes are removable (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container - 3 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area - 1 removable galvanized intermediate table with 1 pair of WADER container pockets - 20 x 20 mm square climbing strips every 200 mm on the outer frame in the chamfer of the loading area - Anti-slip sand coating on the checker plates on the gooseneck and the loading area - Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with position light - Holder for rotating beacon on the warning signs - 80 km/h speed stickers at the rear and on both sides - Load gauge for determining axle loads including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then all defined visible surfaces metalized and hot-finished with ZINACOR 850 (Zinc 85% – Alu 15%)

Stanje: novo, lastna masa: 34.500 kg, največja dovoljena obremenitev: 106.700 kg, skupna masa: 141.200 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.150 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 580 mm, velikost pnevmatike: 285/70 R19.5, barva: siv, obratovalna teža: 34.500 kg, Oprema: ABS, Gooseneck: Bdjdpfx Abswhywfjmsk - Gooseneck hydraulically lift/lowerable as well as detachable - Length approx. 3,650 mm - Extensive lashing positions - For tractor units: 6 x 4 or 8 x 4 3-Axle Compact Front Bogie: - Hook mounts at front and rear - Chassis length x chassis width approx. 3,560 mm x 2,850 mm - Extensive lashing positions Excavator Deck “BB-A”: - Telescopic excavator deck “BB-A” with drive-over deck hooks at the front and bolted lug coupling at the rear - Length x base width approx. 7,150 mm x 2,850 mm - Beam height x beam width approx. 430 mm x 1,350 mm - Loading height 580 mm with 150 mm ground clearance - 5 pairs of hanging lashing rings (LC 10,600 daN) - 4 pairs of threaded blocks M30 on inner beam for mounting screw-on rings 5-Axle Rear Bogie: - Mechanical bolt-on lug coupling for fitting a lowbed front, rear end traverse - Chassis length x chassis width approx. 6,840 mm x 2,850 mm - Extensive lashing positions Pendulum Axle and Tyres (front and rear bogie): - “PENDEL-AXLE”, all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-plugs for securing in lifted position - Final paint of axles with 2 coats of 2K paint, single-colour in MB 7350 Novagrau - Technical axle load: 14,640 kg (62 km/h) - Hydraulic axle compensation - Axle tools - Tyres 285/70 R19.5 Steering Override: - Remote steering from the front and rear via cable remote control with push buttons, including axle tracking control - Socket for steering control operation on the gooseneck - Cable remote control with push buttons including axle tracking control Included accessories: - Yellow-red air couplings on galvanised front connection rail - Steel headboard approx. 400 mm high - 4 wheel chocks with holders - 2 spare wheels 285/70 R19.5 - 3.5" kingpin - Gantry with winch for spare wheel at the front side of the gooseneck - Truck hydraulic connection with flow control valve (40 l/min), including gantry for suspension of supply lines, tractor unit tank must be at least 80 litres with couplings - White reflective tape according to EU regulations on sides and extension, red at rear - Plug-in ALU side panels and rear wall on gooseneck, approx. 400 mm high, anodised - Operating lever on gooseneck protected by folding cover - Separate air connection with air pistol on gooseneck - Central lubrication system BEKAMAX with standard grease NLGI-2: 1x on the gooseneck, 1x on 3-axle bogie, 1x on 5-axle bogie - Variomax tool kit - Multi-coupling hydraulic connections in the lowbed hook area - Front bogie with separate air connection for air screwdriver - Threaded inserts (ø 40 mm) every approx. 500 mm on outside of upper flange of excavator deck for screw rings - Folding extensions with steel mats, width adjustable from approx. 2,850 mm to approx. 3,250 mm - Steel mats with rubber covering approx. 12 mm thick - Two INOX toolboxes 855 x 340 x 390 mm - Radio remote control for steering override in addition to cable remote - Painted sand layer as anti-slip measure - 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery

Stanje: rabljeno, lastna masa: 16.500 kg, največja dovoljena obremenitev: 63.500 kg, skupna masa: 80.000 kg, konfiguracija osi: 3 osi, prva registracija: 02/2024, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Leto izdelave: 2024, obratovalna teža: 16.500 kg, Oprema: ABS, With every used semi-trailer, you receive a current and complete inspection and functional report. Gooseneck: – Gooseneck in SNT design for optimized loading platform length, length approx. 3,700 mm, rear with bevel approx. 1,000 mm x 10° – Technical fifth wheel load: 30,000 kg – Suitable for tractor units: 4x2, 6x2, and 6x4 Bdsdpfx Ajv Aun Asbmsk Load Platform: – Double extendable loading platform, length approx. 8,800 mm with rear bevel approx. 500 mm x 10° – On the central beam, a support plate approx. 300 mm wide is welded front and rear with elongated holes for attachable and relocatable optional bridging elements – Pneumatic locking with tapered locking bolt and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles and Tyres: – BPW axles and suspension, first axle steered, all other axles hydro-mechanically forced-steered – First axle with electro-magnetic reverse lock, activated via reverse gear and manually – Technical axle load: 12,000 kg; air suspension with lift and lower valve – 235/75 R 17.5 3PMSF twin tyres – Load index 143/141J Accessories: – Plug-in steel front wall, approx. 400 mm high – Supply line connector strip for the tractor unit, mounted at external frame rail height – Spiral cable for power supply to electric-hydraulic power unit and/or electric winch (35 mm², 3.5 m long) between trailer and tractor unit with plug – 3 kW electric-hydraulic aggregate for controlling hydraulic operations, except hydraulic winches – Parking position for warning boards on the gooseneck when not in use – 1 spare wheel – On the gooseneck: 1 pair of plug-in side ALU drop sides, approx. 400 mm high, anodized – On the gooseneck: 1 plug-in ALU rear wall, approx. 400 mm high, anodized – Hardwood floor covering on the sloped section of the platform – 3.5" king pin (optional 2") – Guide plate from gooseneck for fifth wheel plate, approx. 500 mm wide – 2 wheel chocks with holders – Mechanical landing gear with 2-speed gearbox and crank – JOST Modul B – static test load = 50,000 kg – Continuous hardwood floor covering (approx. 50 mm thick) on platform and interrupted between axles – Platform locking with conically welded arresting profiles, on the first 3,000 mm extension of the sliding tube, one locking point every 500 mm – Elongated holes for attachable and relocatable bridging elements: at the front of the platform – Extendable galvanized widenings, approx. 230 mm per side – 1 pair of mechanical rear supports – Central lubrication system with 1 pump – One-piece INOX toolbox, approx. 2,480 x 340 x 390 mm – Radio remote control for steering, in addition to cable remote control, with 2 control lights at the receiver for single-track steering monitoring – 2 axle load gauges mounted on the left side, including axle load diagram – 1st axle with automatic lift axle function – 4 warning boards, approx. 423 x 423 mm, extendable – Complete HRM metalization (High Resistance Metallization) – Complete steel structure shot-blasted, then hot-finished with ZINACOR 850 (Zinc 85% – Alu 15%)

Stanje: novo, lastna masa: 13.250 kg, največja dovoljena obremenitev: 47.550 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, vzmetenje: zrak, velikost pnevmatike: 245/70 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings 30 mm thick hardwood flooring Extendable loading platform: Loading platform in extendable design with rear chamfer approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings 3 pairs of outward-folding lashing rings 1 pair of flat lashing rings at the front of the loading area Cut-outs in the outer frame of the loading area for inserting tension straps Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Two-part steel ramps: One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering. Ramp with hydraulically folding and unfolding parts, hydraulic lifting system, and hydraulically adjustable position. Maximum load per pair: 40,000 kg Landing legs: JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced-steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool Tires 245/70 R 17.5 Braking system: Braking system according to EU regulations with EBS-E (4S3M) without connecting lines to tractor unit Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer High-quality one-color two-component (2K) top coat in Novagrau Rear section metallized and painted in RAL 9010 (pure white) Metallic paint not possible Bdjdpfx Asl Uxdksbmek Electrical system: Electrical system according to EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connections conforming to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" kingpin One galvanized steel headboard approx. 400 mm high At the galvanized front connection strip, yellow-red air couplings 4 wheel chocks with holders at the headboard One spare wheel with holder in front of the headboard Electro-hydraulic power unit Rear and front remote steering via cable remote control with push-buttons, with single-track control of the axles Bracket at rear of gooseneck for ALU drive-on ramps European reflector signs (red-yellow) at trailer rear White reflective tape according to EU regulations at the sides, at the extension, and red at the rear At the gooseneck and on the ramps left and right, each with a holder for warning signs including socket One holder for beacon at trailer rear Galvanized folding supports under the loading platform chamfer Ramp operating valves fitted on the right side of the trailer Cover plates to bridge the gap between ramps and loading platform One mudflap at trailer rear Manual and description on USB stick Central lubrication system BEKAMAX (Pico) with general-purpose grease NLGI-2 and removable pump guard On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm The rear galvanized stakes are removable, superstructure length approx. 2,560 mm One INOX toolbox 1,350 x 400 x 400 on the gooseneck, box covers oil filler cap 4 pairs of WADER container pockets in the loading area for a

Stanje: novo, lastna masa: 17.250 kg, največja dovoljena obremenitev: 48.700 kg, skupna masa: 66.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.550 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 375 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 17.250 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize loading platform length, approximately 3,750 mm long - Gooseneck hydraulically liftable, lowerable, and detachable - For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Lowbed: - Lowbed with external beams, designed as a telescopic vessel bridge in low-profile construction with front extension - Length x width approx. 7,550 mm x 2,740 mm - Mechanical locking of the extension Chassis: - Rear chassis with closed outer frame - Checker plate surface and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, Suspension, and Tyres: - “PENDEL-AXLE”, all axles hydromechanically forced steered - Burst protection valve on the axle compensation cylinders with automatic reset function - Hydraulic cylinders with shut-off valves and plug pins for securing in raised position - Final coating of axles: two coats of single-color 2-component paint in "FAY-Grey-34-0260" - Technical axle load 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 Accessories: - Detachable steel front wall, approx. 400 mm high - 4 wheel chocks - Rear upper gooseneck area closed with removable cover - 1 pair of steel ramps with climbing bars and locking bolts to bridge the lowbed mounting hooks - Ramps can be positioned over or between the hooks - Mounting options for steel drive-on ramps at the rear, between the outer beams of the gooseneck - Locking point approx. every 1,000 mm on the extension - 1 lashing ring each, left and right, on the front cross member - Supply line connection strip for tractor unit, mounted at the height of outer frame profile - 6 pairs of threaded blocks on the exterior of the load floor inner beams for attaching M24 screw rings - 6 pairs of recessed lashing rings on the outside of the load floor outer beams, foldable inwards and outwards - 1 pair of threaded blocks on the front and rear of the load floor outer beams for M24 screw rings - Mounting rail for loose aluminum approach ramps on the end cross member of the vehicle - Central lubrication system with 2 pumps, brand BEKAMAX - Remote steering front and rear, cable remote controlled, with axle tracking control - 3 kW electro-hydraulic power unit for hydraulic operations, except hydraulic winches - Removable galvanized loading floor, can be placed in 3 elements between the outer beams, with hardwood covering - Foldable extensions, approx. 230 mm per side - Loose extension boards, steel-edged Bsdpfx Aboh Hm Tzomedk - 4 warning signs approx. 423 x 423 mm - Radio remote control for rear steering - 3.5” kingpin - Anti-slip coating on the left chamfer of the gooseneck - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Guide plate from gooseneck for the fifth wheel plate, approx. 800 mm wide - 1 spare wheel with mounting adapter - Parking position on the gooseneck for warning signs when not in use - 2 pairs of stake pockets integrated into the chassis outer frame, for plug-in stakes approx. 100 x 50 mm - Excavator stick trough of rear chassis closed at the rear with a removable plate - Trailer color: Mercedes-Benz 7350 Novagrey

Stanje: novo, največja dovoljena obremenitev: 49.000 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with front corners chamfered at 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Extendable Loading Platform: - Loading platform, extendable design with rear chamfer of approx. 1,000 mm x 8° - 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) - 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - 1 pair of horizontal lashing rings at the front of the loading platform (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for securing straps (LC 2,000 daN) - Hardwood flooring approx. 48 mm thick, checker-plate covering above the axles Two-Part Removable Ramps: - One pair of galvanized two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp sections, hydraulic lifting mechanism, and hydraulic side-shift - Maximum load per pair: 40,000 kg Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Axles and Tyres: - BPW axles, two fixed axles and two steering axles (self-steering), air suspended, with drum brakes, raise/lower function - Self-steering axles with electro-magnetic reverse lock, can be activated by reverse gear or manually - Axle tool kit - Tyre size 235/75 R 17.5 Brake System: - Braking system according to EU regulations with EBS-E (4S3M) Steel Structure: - Steel structure made of high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Paintwork: - First-class, long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component (2K) zinc dust primer - High-quality single-tone topcoat using 2-component (2K) paint in Nova grey Electrical System: Bdsdoh Etf Rspfx Abmok - Electrical system according to EU regulations, 24 volt lighting, ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX on the front connector strip with 24N, 24S, and 15-pin sockets Included Accessories: - 2" kingpin - Galvanized steel front wall, approx. 400 mm high - One spare wheel with holder in front of the headboard - Yellow-red air couplings on the galvanized front connector strip - 4 wheel chocks with holders on the front wall - Mount at the rear section of the gooseneck for ALU approach ramps - Galvanized folding supports underneath the loading platform chamfer - One holder for warning beacon - Cover plates to bridge the gap between ramps and loading platform - White reflective tape on the side, red on extension and rear, according to EU regulations - Electro-hydraulic power unit - At the gooseneck and ramps (left/right) a holder each for warning signs including socket - Control valves for the ramps mounted on the right side of the trailer - One mud flap at the rear of the trailer - Manual and documentation on USB stick - On the gooseneck, plug-in ALU side boards and rear wall approx. 2,440 x 400 mm - Rear galvanized plug-in stakes are removable (body length approx. 2,560 mm) - 4 pairs of WADER container pockets in the loading platform for one 20ft, two 20ft or one 40ft container - 7 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading platform - Galvanized, extendable platform wideners approx. 230 mm per side - Lift axle on the front axle with control system - 20 x 20 mm square climbing bars - BEKAMAX central lubrication system - Four warning signs extendable by approx. 400 mm eac

Stanje: novo, lastna masa: 15.450 kg, največja dovoljena obremenitev: 65.550 kg, skupna masa: 80.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 21.900 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 925 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimized platform length, approx. 3,700 mm long, with rear tapering of approx. 1,000 mm x 10° Technical fifth wheel load: 30,000 kg. For tractors: 4x2, 6x2, and 6x4 Loading Platform: Double-extendable loading platform, approx. 8,800 mm long with rear taper of approx. 500 mm x 10°. A support table approx. 300 mm wide is welded to the central beam, featuring elongated slots at the front and rear for optional bridge elements that can be hooked in and repositioned Pneumatic locking with conical locking pin and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles and Tyres: BPW axles and suspension, first axle self-steering, all other axles hydraulically and mechanically forced-steered First axle equipped with an electro-magnetic reverse lockout, activated via reverse gear and manually. Technical axle load: 12,000 kg. Air suspension with lift and lower valve Manufacturer by our choice Sockets and Lighting: 24-volt lighting system in accordance with EU regulations ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Complete HRM metallizing Full steel construction, shot-blasted, then hot-finished with ZINACOR 850 Paintwork: 6-stage finishing process: Complete steel construction shot-blasted after welding 1 coat of zinc-based primer, 1 coat of adhesion primer. Final paintwork in 2 coats of 2K paint in single-tone DB 7350 Novagrau, followed by cavity sealing with special wax Accessories: Detachable front wall made of steel, approx. 400 mm high Connection strip for supply lines to the tractor unit, fitted at the height of the outer frame profile ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets. If your pin configuration deviates from the ISO connector standard, please inform us 3 kW electro-hydraulic power unit for hydraulic functions (excluding hydraulic winches) 1 pair of plug-in ALU sidewalls on the gooseneck, approx. 400 mm high, anodized finish 3.5'' king pin. Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide 2 wheel chocks with holder in front of the front wall Mechanical landing legs with 2-speed gearbox and crank Control valves for hydraulic ramps located on the right side of the vehicle 1 pair of mechanical rear supports Central lubrication system with 1 pump, BEKAMAX brand, using standard grease according to NLGI-2 Removable guard covering the pump(s) of the central lubrication system Remote steering from front and rear, controlled by cable remote with push buttons, with axle tracking control, no installation required on tractor unit Under the gooseneck and on the rear crossmember, one 7-pin socket with holder for warning signs each on left and right. One 7-pin socket on the rear crossmember Manual and documentation One-piece INOX stowage box, approx. 2,480 x 340 x 390 mm, straight design Bsdpfx Asrigw Rjbmsdk Please note that any special equipment and accessories will increase the unladen weight and correspondingly reduce the payload Warning package: 4 warning boards, approx. 423 x 423 mm, extendable by approx. 1,000 mm, incl. 2 LED position lights and brackets for beacon.

Stanje: novo, največja dovoljena obremenitev: 38.100 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.100 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5 3PMSF, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer of approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading platform: 5 pairs of fold-out lashing rings 3 pairs of fold-out lashing rings 1 pair of horizontal lashing rings at the front of the loading area Cut-outs in the outer frame of the loading surface for hooking in tension belts Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Landing legs: JOST landing legs with 2-speed gears for a 24 t lifting capacity Axles and tyres: BPW axles, two axles are fixed, two axles are self-steering, air-suspended, with drum brakes, with lift/lower function The self-steering axles come with an electro-magnetic reverse lock, which is activated via reverse gear or manually Axle toolkit Tyres: 205/65 R17.5 3PMSF Brake system: WABCO brake system according to EU regulations with EBS-E Steel construction: Steel structure made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Electrical equipment: Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK lighting ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component zinc dust primer High-quality single-colour 2-component top coat in MB 7350 Novagrau No metallic paint possible Rear section metallized and painted in RAL 9010 Accessories included: 1 spare wheel 205/65 R 17.5 TPMS tyre pressure monitoring system acc. to ECE R 141 At the galvanized front connection strip yellow-red air couplings 4 wheel chocks with holder on front wall Bracket at rear of gooseneck for ALU access ramps Galvanized folding supports under the chamfer of the loading surface Mount for a revolving beacon at the rear of the trailer Height-adjustable curtain structure Galvanized front wall with a tension mechanism for the sliding curtains Height-adjustable by approx. 400 mm "EDSCHA" brand roof, sliding forward on ALU roof beam profiles, bolted to the front and rear wall In the loading surface, 3 pairs of sliding stakes Superstructure at rear hydraulically extendable to left and right by approx. 750 mm Sliding roof with upward swinging portal carrier Sliding tarp with 700 mm reserve length, with tension straps at intervals of approx. 600 mm Height to top edge of superstructure approx. 3,960 mm Journeys with the sliding roof open are not permitted and will damage the tarp Mounting rail for ALU access ramps at the rear of the vehicle At the gooseneck and at the rear panel left and right, each with a mount for warning signs incl. socket A mud flap at the rear of the trailer European reflector plates at the rear of the trailer 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading area Lifting axle on the front axle controlled by TEBS E depending on current axle load and load status Rear structure with closed ALU double-wing doors Bdjdpetphtmjfx Abmok A sanded, anti-slip paint layer on the checker plates on the gooseneck and on the loading surface BEKAMAX centralized lubrication system with standard grease NLGI-2 and a removable guard around the pump Speed stickers 80 km/h on rear and both sides Load manometer for axle load determination including load chart

Stanje: novo, lastna masa: 12.900 kg, največja dovoljena obremenitev: 34.100 kg, skupna masa: 47.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 350 mm, vzmetenje: drugo, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 12.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm in length - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2, and 6x4 Loading Platform: - Low-bed with external beams, extendable “SUPER LOW” design, approx. 6,850 mm in length - Low-bed with fixed hardwood flooring, approx. 40 mm thick, with mechanical locking device Rear Chassis: - Rear chassis with closed outer frame, chequer plate covering, and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings, foldable to the outside - 1 pair of lashing rings recessed in the trough - 2 pairs of stake pockets for insertable stakes 100 x 50 mm in the external frame Pendulum Axle and Tyres: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and safety locking pins for securing in raised position - Axles painted with two layers of single-colour 2K paint in “FAY-Grey-34-0260” - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 - TPMS tyre pressure monitoring system according to ECE R 141 Accessories: - Preparation for the installation of bolt-on container locators for 1 x 20ft or 1 x 40ft container on the outer girders - 2" king pin - One galvanized steel front wall, approx. 400 mm high - One spare wheel - Yellow-red air couplers on the galvanized front connection bar - 4 wheel chocks - Remote steering from front and rear, operable via wired remote control with push buttons, with single-track alignment control - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of screw couplings - Electro-hydraulic power unit - White reflective tape in accordance with EU regulations on sides, extension, and rear - European reflective plates (red-yellow) on the rear of the trailer - One bracket on each side of gooseneck and rear plate for warning panels, including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on outer beam for mounting screw-on RUD Rings VLBG-4 - Detachable ALU side boards and rear board on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized insertable stakes are removable (body length approx. 2,560 mm) - Gooseneck rear upper area covered with removable cover - 5 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading area - Folding extensions, approx. 230 mm per side - 2 pairs of bolted RUD Rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the mounting hooks of the low-bed Bdsdpfohlz R Sex Abmjk - Anti-skid sand layer painted on loading surface - 80 km/h speed stickers at rear and both sides - Spoon boom trough at rear chassis closed at rear with plug-in plate - Four extendable warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for rear axle steering in addition to cable remote, with indicator lights on receiver for alignment control - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard NLGI-2 grease - Load pressure gauge for determining axle loads - HRM Metallisation (High Resistance Metallisation) of outer frame - Complete steel structure shot blasted, then all defined visible areas metallized and finished with ZINACOR 850 (zinc 85% - aluminium 15%) hot galvanizing

Stanje: novo, lastna masa: 8.490 kg, največja dovoljena obremenitev: 40.510 kg, skupna masa: 49.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.550 mm, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 8.490 kg, Oprema: ABS, Chassis: Bjdswu A Slepfx Abmjdk - Robust welded steel frame structure with front frame drop and flat loading platform with rear bevel, approx. 500x100 mm - Gooseneck height 200 mm with beveled corners - Gooseneck end with bevel approx. 500 x 100 mm (traction ribs on outer frame in the area behind rear bevel) - 2 kingpin positions with interchangeable 2" kingpin - Outer frame closed outwards as slotted rail for lashing with tie-down straps - Reinforced frame design / point load at center of gravity - Provisions for extendable deck wideners - With excavator trough (without cover), approx. 220 mm deep, 600 mm wide, starting after the 2nd axle to end of vehicle - 1 pair wheel recesses in front of the axle with steel covers (covers with Körapur coating), approx. 400 mm deep, plus 1 pair wheel recesses between the 1st and 2nd axle with steel covers - Underride protection = extended end plate - Hydraulic drop-down supports at rear Floor: - 35 mm larch timber floor with aluminum omega profiles Axles, Steering, and Tyres: - BPW air suspension axles, each rated at 10 t axle load, bellows diameter 360 mm - S-cam brake 300/200 mm, asbestos-free brake linings - Automatic slack adjusters - Lifting and lowering device, total lift approx. 200 mm - 2nd driving height via ball valve +50mm - 1st axle lift axle (wired through EBS), fully automatic actuation with manual emergency actuation via button on trailer - 3rd axle as friction-steered trailing axle with electric and mechanical locking - 12 steel disc wheels, 10-hole, hub-centered - 12 tyres 245/70 R 17.5 143/141J, tubeless - Incl. tyre pressure monitoring system Braking System: - Dual-line brake system with EBS-E including RSS - EBS (WABCO 4S3M) - Spring-loaded parking brake - Pneumatic connection yellow/red Paintwork: - Steel shot blasting, spray galvanising of chassis and primer - Painting of chassis/wheel hubs/outer frame in DB 7350 Novagrau Accessories: - Removable side and rear boards on the gooseneck, approx. 400 mm high - Spare wheel holder - Side aluminum underrun protection - 4 wheel chocks - Steel fenders with Clear-Pass - Long license plate holder in end plate - 1 removable ECE plate at the rear - 11 pairs ZK modules 10t lateral: - 2x on the gooseneck - 9x on the loading platform - Without rear towing eyes - Extendable warning signs including 3 position lamps each, front at landing legs and rear in front of end plate, steplessly extendable up to 4,500 mm load width - 4 insertable sockets for warning signs in stake pockets on loading platform - 6 pairs stake pockets along sides for 100x50 mm stakes - 2 cross rows of stake pockets for 100x50 mm stakes on the gooseneck from outside frame to main frame (1 before and 1 after kingpin positions) - 3 cross rows of stake pockets for 100x50 mm stakes on loading platform from outer frame to main frame (1 in front section, 1 before 1st axle, 1 after 3rd axle) - 2 pairs steel plates on loading platform for container locks to accept 1x 20ft container - Rubber skirt mounted on underrun protection - Preparation (cable routing for NATO cable and hole pattern for subsequent mounting of NATO socket at front of end plate and bracket on vehicle) for optional retrofit of electrohydraulic power unit at right rear for potential operation of access ramps - Mechanical 24-ton stabiliser landing gear with single-sided operation and compensating shaft Optional: Trailer available with aluminum folding ramps.

Stanje: novo, lastna masa: 9.300 kg, največja dovoljena obremenitev: 38.700 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.200 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R 22,5, barva: sivo-črna, Oprema: ABS, Cargo Area: • Extendable cargo area with pneumatically operated locking mechanism • Cargo platform with approx. 30 mm thick timber flooring • 7 pairs of external folding lashing rings (LC 5,000 daN) • 3 pairs of external folding lashing rings (LC 10,000 daN) • Cutouts in the outer frame of the cargo area for attaching tensioning straps (LC 2,000 daN) Axles and Tyres: • BPW axles and suspension, all axles hydromechanically forced-steered • Equipped with disc brakes • Technical axle load: 10,000 kg • Air suspension with lift and lower valve • Axle tool kit • Tyres: 385/65 R 22.5 • TPMS tire pressure monitoring system compliant with ECE R 141 Brake System: • WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Electrical System: • Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) • ASPÖCK-UNIBOX at the front control strip with 24N, 24S & 15-pin sockets • Connections as per ISO standards • 24N ISO-1185 • 24S ISO-3731 • 15-pin ISO-12098 Standard Accessories Included: • Remote-controlled steering from front and rear via cable remote control with push buttons, including single-track axle monitoring • 4 wheel chocks with holders mounted on the front wall • 2" king pin • One galvanized steel front wall, approx. 1,600 mm high • Yellow-red air couplings at the galvanized front connection strip • White reflective tape compliant with EU standards on both sides, on extension, and at the rear of the trailer in red • European reflective plates (red-yellow) at the rear of the trailer • One mud flap at the rear of the trailer • Operating manual and instructions • Mount for a revolving beacon at the rear of the trailer • Cargo area with approx. 30 mm thick timber floor inset in omega profiles • 10 pairs of stake pockets (100 x 50 mm) in the outer frame of the cargo bed • 1 spare wheel holder under the cargo area, right-hand side in the direction of travel • Electro-hydraulic unit • At the gooseneck and rear panel left/right, each with bracket for warning signs, incl. socket Bsdjiu Etrspfx Abmsdk • Coated sand layer on the main beam as anti-slip protection • 6 pairs of WADER container pockets in the cargo area for 1x20ft, 2x20ft or 1x40ft containers; additional locking point provided in the extension for a 45ft container • 4 pairs of transverse stake pocket rails in the cargo area for plug-in stakes 100 x 50 mm • Access ladder mounted on the right side in the direction of travel • One HDPE toolbox approx. 1,200 x 500 x 480 mm at the front under the cargo bed, left in the direction of travel • BEKAMAX (Pico) centralized lubrication system with removable pump guard • Lift axle on front axle, controlled via TEBS E according to dynamic axle load and load status • Wireless remote control for steering, in addition to cable operation, with indicator lights on receiver for single-track monitoring • Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm, equipped with position light • Bracket for revolving beacon on the warning signs • 80 km/h speed sticker on rear and both sides • Load gauge for axle load determination, including load chart • HRM (High Resistance Metallisation) of the outer frame • Complete steel construction shot blasted; subsequently, defined visible surfaces metallised by hot-dip application with ZINACOR 850 (85% zinc – 15% aluminium)

Stanje: rabljeno, lastna masa: 10.900 kg, največja dovoljena obremenitev: 43.600 kg, skupna masa: 54.500 kg, konfiguracija osi: 3 osi, prva registracija: 04/2025, dolžina tovornega prostora: 8.700 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 855 mm, velikost pnevmatike: 245/70 r17.5, barva: siv, Leto izdelave: 2025, obratovalna teža: 10.900 kg, Oprema: ABS, Gooseneck, rigid, center tube design: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Steel floor with anti-slip coating - Including perforated rail for aluminum approach ramps - 2" king pin - Manually operated BPW landing legs - 550 mm long, 8° chamfer at end of gooseneck - Front wall including park position for rear wall, 400 mm high - Spare wheel holder mounted vertically on the front side of the gooseneck - 3 pairs of recessed lashing rings (LC 5,000 daN) in the loading area of the gooseneck - Aluminum side boards, 400 mm high, comprising 2x side boards each 3,150 mm long, and rear board with stanchions (galvanized) - Rectangular aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, center - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, left - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, right Loading platform, single-extendable: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Fixed section at front 700 mm - Steel plate floor with anti-slip coating - Chamfered transition between fixed part and deck for bridging rails and wheel recesses - Excavator trough including elongated holes for load securing (LC 1,500 daN), length approx. 3,850 mm - Prepared for hydraulic ramps (electrical supply) - Rails to widen up to 3,000 mm - 8° chamfered vehicle rear, 550 mm long - Slide system for easy mounting/dismounting of ramps - Continuous mud flap at the rear - 1 pair of lashing points LC 10,000 daN centrally on the loading area behind the gooseneck - 7 pairs of lashing points LC 10,000 daN in the outer frame of the loading platform - 6 pairs of stanchion pockets 100 x 50 mm in the outer frame of the loading platform - 1 pair of lashing points LC 10,000 daN centrally in the rear section of the loading platform - 1 pair of stanchion pocket rails approx. center of the loading area - 1 pair of stanchion pocket rails on the fixed part - 1 pair of stanchion pocket rails behind the last axle Ramps: - Hydraulic double-folding ramps, 2,750+1,500x800 mm - Larch wood surface - Operated by remote control (wired and wireless) - Quick-change ramp (dismantling system) Chassis: - Axle brand: BPW ECO Max - 2 ride heights - 4 axles @ 10 t (technically 12 t) Bsdpfoi Ai E Rjx Abmedk - Twin tires 245/70 R17.5 - 2 x rigid axles and 2 x friction-steered axles - Reverse steering lock for friction-steered axles via reverse gear - Brake system by Knorr (according to EU standards with EBS-E) - Knorr TIM G2 (Trailer Information Module) - RSS (Roll Stability Support) stability control - Load-dependent lift axle on the first axle incl. starting aid (forced lowering of lift axle via TIM possible) Accessories: - 4 wheel chocks with holder - 2 pairs of warning panels 423 mm x 423 mm, with 2 position lights and socket for rotating beacon, steplessly adjustable up to 3,950 mm - Securing points on gooseneck and on loading platform (alternatively on ramp, if available) included - Plug-in bulkhead at the end of the excavator trough - Electrohydraulic unit for ramp operation - Ramp control by wireless remote - Hydraulic rear support legs for stabilization during loading - 1 pair of additional reversing lights at the rear, activated when reversing - Larch wood widening planks (option)