Nizki nakladalnik

Fliegl VTS 400

Stanje: novo, največja dovoljena obremenitev: 31.920 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 10.410 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, New Fliegl 4-Axle Low Loader Trailer with Ramps, Type VTS 400 Gross vehicle weight: 24,000 kg / 40,000 kg Unladen weight: 8,080 kg Payload: 15,920 kg / 31,920 kg Overall length: 11,940 mm Loading length: total approx. 10,410 mm, gooseneck approx. 2,490 mm, loading deck incl. rear slope approx. 7,920 mm Todpfx Asxrx I Uoh Eod Width: 2,550 mm Loading height: 900 mm Further information: Plus transportation and provision ex stock 26639 Wiesmoor €1,280 / net Chassis Low Loader Trailer Steel welded construction Turntable with heavy-duty slewing ring Foldable rear supports 2 wheel chocks with holders Aluminium side underrun protection Rear spray flap across the full width Half-shell mudguards on 1st and 2nd axles with anti-spray flaps behind each axle, Anti-spray flaps in front of and behind 3rd and 4th axle Excavator arm trough over the rear axles extending to the rear, approx. 1,800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes, each 5 t, in the excavator arm trough on the side of the longitudinal frame, approx. 300 mm from the front and approx. 200 mm from the rear ramp 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Storage compartment embedded in the floor of the gooseneck with lid, W=720 mm / L=520 mm / D=170 mm Extendable widenings up to 3,000 mm (not in rear slope) (Track width of construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks below the platform 70 mm wooden planks for widening to 3,000 mm Lashing points low loader 1 pair of lashing cut-outs in the longitudinal beam at the front of the gooseneck, each 10 t 4 pairs of lashing holes in the outer frame, each 5 t (for lashing strap hooks) 9 pairs of lashing mushrooms mounted on top and side of outer frame, each 10 t 2 x at the front on gooseneck 7 x on the low-bed deck First lashing ring 250 mm from front and last max. 250 mm from rear, spacing between lashing rings not more than 1,100 mm Additional 3 pairs of folding lashing rings, each 10 t 1 x on gooseneck (protruding) 1 x at the start of the low-bed deck embedded in the longitudinal beams 1 x behind the last axle embedded in the floor Drawbar coupling for turntable trailer Drawbar with tested 50 mm towing eye Drawbar height adjustment via spring Axles + suspension Drum brake axles, manufacturer’s choice "Axle/chassis laser alignment" reduces tyre wear and fuel consumption Air suspension with raise & lower valve + auto-reset function Wheels and tyres 235 / 75 R 17.5" manufacturer’s choice Steel rims in twin configuration, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Axle load detection via EBS-CAN bus signal, for display in driver’s cab, truck must be prepared accordingly, no truck installation (not a calibrated scale) Vehicle stability control system 2 fool-proof coupling heads at the front with connection lines to the tractor unit, 12-24 Volt EBS, electronic braking system with EBS plug at the front, with connecting cable Brand: Knorr Important: The trailer may only be towed by towing vehicles that ensure ABS operation! Electrics 12-24 Volts, multi-chamber LED lights, yellow LED side marker lights, LED license plate lighting (Note: some towing vehicles may display error messages, even though function is OK) 2 white LED position lights at the front 2 white/red LED lane positioning lights at the rear 2 x 7-pin fool-proof plugs at the front, with connecting cable 1 LED beacon with

Stanje: novo, številka stroja/vozila: ee3256d63dd23b3ad1bdf9ab0, lastna masa: 10.280 kg, največja dovoljena obremenitev: 13.720 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with robust ball bearing slewing ring Foldable rear support legs 2 wheel chocks with holders Aluminum side underrun protection Full-width rear mud flaps Quarter shell fenders in front of the 1st axle Excavator arm trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes rated at 5 t each in the excavator arm trough, positioned laterally on the longitudinal frame approx. 300 mm from the front and approx. 200 mm before the rear taper 1 storage box recessed into the gooseneck on the floor with lid, W=720 mm/ L=520 mm / D=170 mm Tedpfxji Ri I Ne Ah Ejd 1st pair of wheel recesses after the gooseneck, recessed in the low-bed deck area, sloped for entry, length at bottom approx. 1600 mm, approx. 400 mm deep. Note! Main frame section 400 mm higher than wheel recess. 2nd pair of wheel recesses between the axles, recessed in the low-bed deck area, sloped for entry, length at bottom approx. 600 mm, approx. 300 mm deep. Note! Main frame section 300 mm higher than wheel recess. Removable wheel recess covers from the main frame, with wooden inserts. Distance from main frame longitudinal member to outside member approx. 1280 mm (wheel recess area) Extensions extendable to 3,000 mm, foldable at the wheel recess extensions (extensions not in the rear taper nor at the bottom of the wheel recesses) (The track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for timber planks centrally on load area or underneath depending on technical feasibility 70 mm timber planks for extension to 3,000 mm Low-bed lashing points 1 pair of ring lashing points recessed in the gooseneck, each rated at 5 t 8 pairs of lashing mushrooms recessed in the top and side outer frame, each rated at 10 t 2 x at the front on the gooseneck 6 x in the low-bed – first lashing point 250 mm from the front, last maximum 250 mm from the rear, distance between lashing points not greater than 1100 mm 5 pairs of ring lashing points recessed in the outer frame, each rated at 5 t (can be converted to stake pockets) Drawbar Assembly for Turntable Trailer Drawbar with tested 50 mm towing eye, towing eye inclined at 8° Axles + Suspension SAF drum brake axles Axles/chassis laser-measured to reduce tire wear and fuel consumption Air suspension with lift & lower valve, separately operable at front and rear Wheels and Tires 235 / 75 R 17.5 Manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line pneumatic braking system Spring-loaded parking brake Trailer info center, displays vehicle data (e.g., axle load—not a calibrated scale) and odometer Axle load detection via EBS-Canbus signal, for display in the cab (truck must be pre-equipped, not installed in truck, not a calibrated scale) Vehicle Stability System Duomatic coupling at the front with connecting line to the truck tractor EBS, electronic braking system with EBS socket at the front, with connecting cable Note: The trailer may only be towed by vehicles that ensure proper ABS function! Electrics 24 volts, multi-chamber LED lights with resistor, side marker yellow LED lights, LED license plate lights (Note: Certain towing vehicles may show diagnostic errors despite systems working correctly) 2 white front position lights in LED 2 white/red lane marker lights at the rear in LED Additional LED w

Stanje: novo, največja dovoljena obremenitev: 31.920 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 10.410 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, New vehicle: Fliegl 4-axle low-loader trailer with ramps, model VTS 400 Gross weight: 24,000 kg / 40,000 kg Unladen weight: 8,080 kg Payload: 15,920 kg / 31,920 kg Overall length: 11,940 mm Loading length: total approx. 10,410 mm; neck approx. 2,490 mm; loading bed incl. rear taper approx. 7,920 mm Width: 2,550 mm Loading height: 900 mm Further information: Plus pre-freight / preparation ex stock 26639 Wiesmoor: €1,280.00 / net Chassis: Low-bed trailer Steel welded construction Turntable with heavy-duty ball race ring Foldable rear support 2 wheel chocks with holders Side underrun protection, aluminium Full-width rear mud flap Half-shell mudguards, 1st and 2nd axles with anti-spray flaps behind each axle, Anti-spray flaps in front of and behind 3rd and 4th axles Excavator stick trough over rear axles to the rear, approx. 1,800 mm long, 650 mm wide, 150 mm deep 2 pairs of lashing holes, each 5 t, in the excavator stick trough on the longitudinal frame, approx. 300 mm from the front and 200 mm in front of the rear slope 1 plastic toolbox, w=600 mm / h=425 mm / d=460 mm, lockable Storage box recessed in the neck floor with lid, w=720 mm / l=520 mm / d=170 mm Extendable outriggers to 3,000 mm (not for rear slope) (Track width of construction machinery/vehicles to be transported must not exceed external frame width of 2,550 mm) Storage compartment for wooden planks under the low-bed deck Wooden planks, 70 mm, for extension to 3,000 mm Lashing points, low-loader: 1 pair of lashing cutouts in the front longitudinal beams, embedded in the neck, each 10 t 4 pairs of lashing holes in the outer frame, each 5 t (for attaching ratchet straps) 9 pairs of lashing mushrooms, embedded in and above the outer frame, each 10 t: - 2 × on the neck - 7 × in the low-bed section First lashing point 250 mm from the front, last max. 250 mm from the rear; lashing point spacing max. 1,100 mm Additionally, 3 pairs of folding lashing eyes, each 10 t: - 1 × on the neck (protruding) - 1 × at the start of the low-bed inside the longitudinal beams Tsdpoxrx Nlofx Ah Eod - 1 × in the floor behind the last axle Drawgear, turntable trailer: Drawbar with certified 50 mm eye Drawbar height adjustment via spring Axles & Suspension: Drum brake axles, per manufacturer’s choice "Axles/chassis laser-aligned" to reduce tire wear and fuel consumption Air suspension with lift & lower valve + auto-reset function Wheels and Tyres: 235 / 75 R 17.5", per manufacturer’s choice Steel twin wheels, factory silver Braking system: 2-line air-operated brake system Spring-loaded parking brake Axle load detection via EBS CAN bus signal for display in truck cab (truck must be equipped accordingly; not a calibrated scale) Vehicle stability system: 2 non-interchangeable coupling heads at the front, connection lines to the tractor 12-24V EBS, electronic braking system with EBS socket at the front, including connecting cable (Knorr brand) Attention: The trailer may only be towed by vehicles that guarantee ABS functionality! Electrics: 12-24V, multi-chamber LED lights, side LED marker lights (yellow), LED license plate lighting (Note: Some towing vehicles may display incorrect errors despite proper function) 2 white front position lights, LED 2 white/red rear lane marker lights, LED 2 × 7-pin non-interchangeable sockets at the front, with connection cable 1 LED rotating beacon with bracket, switchable via sidelights (removable beacon) 2 pairs...

Stanje: novo, številka stroja/vozila: 55d3c5c03e032385649769b1b, lastna masa: 9.900 kg, največja dovoljena obremenitev: 14.100 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-Loader Trailer Steel welded construction Turntable with heavy-duty slewing ring, integrated storage box incl. Turntable front structure Foldable rear support 2 wheel chocks with holders Aluminum side underrun protection Full-width rear mud flaps Extendable widenings to 3,000 mm (not at rear taper) (track width of the machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Central compartment on loading area for timber planks 70 mm timber planks for widening to 3,000 mm Lashing points Low-loader 3 pairs of integrated lashing points, each rated to 10 t, at the front floor 6 pairs of mushroom lashing points, top and side integrated in outer frame, each 10 t 1 x at neck area remaining points distributed, distance no greater than 1,200 mm 1 x at rear taper 5 pairs of stake pockets integrated in the outer frame, internal size 70 x 40 mm (convertible to 5 t ring lashing eyes, not included) Drawbar assembly for trailer turntable Drawbar with certified 40 mm towing eye Note: For 40 mm towing eye, the maximum permissible gross weight of the towing vehicle is 18,000 kg. Otherwise, a 50 mm towing eye is required. Axles + Suspension SAF drum brake axles Laser-aligned axles/chassis to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization front and rear (rocker compensation) Wheels and Tires 235 / 75 R 17.5 manufacturer's choice Steel twin wheels, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connection lines to the truck ABS and ALB, with ABS connector at front, connection cable included Attention: The trailer may only be towed by vehicles that ensure ABS functionality! Electrics 24-volt multi-chamber lights, side yellow LED lighting 2 white front position lights 2 white/red rear lane marker lights 2 x 7-pin non-interchangeable connectors at the front, with connection cable 1 LED beacon with bracket, operated via parking lights (removable beacon) 2 pairs of warning boards, double LED-lit and extendable to 3,000 mm Floor Steel floor at front section thereafter 70 mm softwood floor, in wheel arch area with steel/chequer plate covering Rear taper with 70 mm softwood floor Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable wooden inlays spring-assisted lifting Operating instructions Exception permit required for 10,000 kg axle load, only indivisible loads allowed!!! The specified total weight is technically possible. Depending on the cargo, the full gross weight may not be achieved while observing permissible axle/pin/support loads (poor tracking and handling may result from incorrect load distribution) Country of Registration / Plates Registration country: Germany 1 with Dekra inspection and report (according to §13 EC-FGV) 24/7 service hotline prepared for 2-line license plate holder Conspicuity markings with reflective strips acc. ECE R 048, white on the sides, red at the rear Paint Frame RAL 3002 Carmine Red Todsi Ri I Eepfx Ah Eod 10 years warranty against rust-through Drawbar galvanized or black, at manufacturer's discretion Loading ramps hot-dip galvanized Attention: Archive photos!

Stanje: novo, največja dovoljena obremenitev: 31.920 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 10.410 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, New Fliegl 4-Axle Low Loader Trailer with Ramps, Type VTS 400 Gross weight: 24,000 kg / 40,000 kg Unladen weight: 8,080 kg Payload: 15,920 kg / 31,920 kg Overall length: 11,940 mm Load length: approx. 10,410 mm total, stepped area approx. 2,490 mm, loading bed incl. rear ramp slope approx. 7,920 mm Width: 2,550 mm Loading height: 900 mm Further information plus pre-carriage / delivery from stock location 26639 Wiesmoor €1,280.00 net Chassis Low Loader Trailer Robust steel welded construction Turntable with heavy-duty ball bearing race Rear supports, foldable 2 wheel chocks with holders Aluminium side underrun protection Full-width rear mudflap Partial shell fenders on 1st and 2nd axle with anti-spray mudflaps behind each axle Anti-spray mudflaps before and after 3rd and 4th axle Excavator arm recess starting from the rear axles towards the end, approx. 1800 mm long, approx. 650 mm wide, approx. 150 mm deep 2 pairs of lashing holes, each rated for 5 t, in the excavator arm recess on the side of the main frame approx. 300 mm from the front and approx. 200 mm before the rear ramp slope 1 plastic toolbox, lockable, dimensions: w=600 mm / h=425 mm / d=460 mm Recessed stowage box in the floor of the stepped area with cover, W=720 mm/L=520 mm/D=170 mm Extendable widenings up to 3,000 mm (not at the rear ramp slope) (Note: Track width of transport machines/vehicles must not exceed outer frame width of 2,550 mm) Storage compartment for wooden planks beneath the low loader deck 70 mm wood planks for extending to 3,000 mm width Lashing points Low Loader 1 pair of lashing cut-outs at the front, recessed into the main beam at the stepped area, each rated for 10 t 4 pairs of lashing holes on the outer frame, rated for 5 t each (suitable for lashing straps) 9 pairs of lashing mushrooms, recessed in the top and sides of the outer frame, each rated for 10 t: 2 x front on the stepped area 7 x in the low-bed area First lashing point 250 mm from the front, last max. 250 mm from the rear; distance between lashing points not more than 1,100 mm 3 additional pairs of folding lashing eyes, each rated for 10 t: 1 x over the stepped area 1 x at the beginning of the low-bed, recessed into the main beams 1 x behind the last axle, recessed in the floor Drawbar Assembly Turntable Trailer Drawbar with certified 50 mm towing eye Drawbar height adjustable via spring Axles & Suspension Drum brake axles, manufacturer's choice Axle/chassis laser alignment for reduced tyre wear and fuel consumption Air suspension with lift & lower valve, auto-reset function Wheels and Tyres 235/75 R 17.5”, manufacturer’s choice Steel twin wheels, plant silver Brake System 2-line compressed air brake system Spring-loaded parking brake Axle load detection via EBS CANbus signal, for display in the truck cab (truck must be equipped, not installed, not a certified weighing system) Vehicle Stability Control System 2 plug-safe coupling heads at the front with linkage to prime mover 12-24 Volt EBS, electronic braking system with EBS connector in front, incl. cable Brand: Knorr Note: The trailer may only be towed by vehicles that can guarantee ABS function! Electrics 12-24 Volt, multicompartment LED lights, LED side marker lights, LED number plate lighting (Note: With certain towing vehicles, incorrect diagnostics may occur despite proper function) Tjdpfx Ajxrx Nfeh Ejd 2 white front position lights in LED 2 white/red Lane marker rear lights in LED 2 x 7-pin plug-safe connectors in front, incl. cable 1 LED beacon with

Stanje: novo, številka stroja/vozila: 408ba9a39bbb8087056d6e563, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support Todpji Ri Daefx Ah Esd 2 wheel chocks with holders Side underrun protection made of aluminium Full-width rear mudflap Half-shell fenders on 1st and 2nd axle with anti-spray mudflaps behind each axle; anti-spray mudflaps in front of and behind 3rd and 4th axle Excavator arm recess over the rear axles, starting to the rear, approx. 1800 mm long, approx. 650 mm wide, and approx. 150 mm deep, 2 pairs of lashing holes each rated 5 t located laterally in the excavator arm recess in the main chassis, approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 plastic toolbox with shelf, w=620/h=360/d=440 mm, lockable with a padlock (Padlock not included) 1 storage box let into the gooseneck in the floor with lid, w=720 mm/ l=520 mm / d=170 mm Extendable width to 3,000 mm (not at the rear bevel) (the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) 70 mm timber planks for widening to 3,000 mm Storage compartment for timber planks under the loading platform Lashing rings low-loader (40 lashing possibilities) 1 pair of lashing rings on gooseneck, each 5 t 9 pairs of lashing mushrooms recessed into the outer frame, top and side, each rated 10 t 2 x in the front on the gooseneck 7 x in the low-bed 6 pairs of lashing holes in the outer frame of the low-bed, each rated 5 t (for lashing strap hooks) 3 additional pairs of folding lashing rings, each rated 10 t 1 x inside beside the main frame at the beginning of the low-bed 1 x on the gooseneck (protruding) 1 x recessed into the floor behind the last axle Drawbar coupling for turntable trailer Drawbar with certified 50 mm towing eye, towing eye inclined at 8°, D-value at least 160 kN Axles & Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker equalisation) Wheels and Tyres 235 / 75 R 17.5 manufacturer’s choice Steel rims, twin mounting, factory silver Brake System 2-line compressed air brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, including connection lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connection cable Electrics 24 volt, multi-chamber lamps, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin non-interchangeable plugs at the front with connecting cable 1 LED beacon with holder, operated via parking light (beacon removable) 2 pairs of warning boards, double LED illuminated and extendable to 3,000 mm Flooring Gooseneck at front with steel/chequer plate floor Then with 70 mm softwood floor, in wheel arch area steel/chequer plate covering Rear bevel with 70 mm softwood floor Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber decked Hydraulically operated via tractor PTO with restrictor, control located on the left side at the front Hydraulic connection with SVK connector NW 10/3, incl. connecting hose Registration Country/Plates Registration country: Germany 24/7 Service Hotline Prepared for two-line number plate holder Contour marking with reflective strips according to ECE R 048, side white and rear red Warning plate according to ECE – 70 Paintwork Chassis hot-dip galvanized including passivation, 15-year warranty again

Stanje: novo, največja dovoljena obremenitev: 30.310 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, NEW VEHICLE Fliegl 4-axle low loader with 2 pairs of wheel recesses and ramps Gross weight: 40,000 kg Payload: 30,310 kg Unladen weight: 9,690 kg Overall length: 12,000 mm Loading length: 10,000 mm Loading bed: 7,150 mm including 850 mm drive-on slope Loading height: 900 mm 1st pair of wheel recesses after drop in the loading bed, length at bottom approx. 1,600 mm, 400 mm deep 2nd pair of wheel recesses between the axles in the loading bed, length at bottom 600 mm, 300 mm deep Extensions to 3,000 mm, warning boards, rotating beacon, comprehensive lashing package 5 pairs of stake pockets in the outer frame Excavator arm recess, 1,800 mm long, 150 mm deep Drawbar 50 mm Air suspension with raise/lower valve, separately operable BPW drum brakes Tyres: 235 / 75 R 17.5" Axle load detection via EBS CAN bus signal, Trailer Info Center Ramps: 2,800 mm x 750 mm, hydraulically operated Hydraulic lateral displacement Hire purchase offer: term 48 months, residual value 40%, down payment only the VAT on the installments, monthly payment EUR 970.00 net Vehicle available from 11.09.2023 from the Neumünster trade fair. Visit us at Nordbau - Stand West 121, right next to the main entrance. Tjdpfjnzlg Djx Ah Eed Further 3-, 4- and 5-axle low loaders new and used available immediately

Stanje: novo, največja dovoljena obremenitev: 31.100 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 10.410 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.520 mm, Gross weight: 24,000kg / 40,000kg Curb weight: 8,900kg Payload: 15,100kg / 31,100kg Total length: 11,940mm Loading length: 10,410mm total, 2,490mm gooseneck, 7,920mm loading deck including rear bevel Width: 2,520mm Loading height: 900mm Further information: plus pre-carriage / provision ex stock location 26639 Wiesmoor: €1,280.00 net Steel welded construction Turntable with heavy-duty ball-bearing slewing ring Foldable rear support Wheel chocks with holder Aluminium side underrun protection Rear mudflaps across the full width (not in combination with forklift holder) Half-shell fenders on 1st and 2nd axles with anti-spray mudflaps behind each axle Anti-spray mudflaps in front of and behind 3rd and 4th axles Excavator arm recess over rear axles to the rear, approx. 1,800 mm long, approx. 650 mm wide, approx. 150 mm deep 2 pairs of lashing holes (5 t each) in the excavator recess at the side of the longitudinal frame, approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable 1 storage box embedded in gooseneck floor with lid, W=720 mm / L=520 mm / D=170 mm Extendable width to 3,000 mm (not in rear bevel) (Track width of machines/vehicles to be transported must not exceed outer frame width of 2,550 mm) Storage compartment for timber planks under low-bed platform 70 mm timber for widening to 3,000 mm Low loader lashing eyes 1 pair of lashing cut-outs at the front longitudinal member in gooseneck, each rated 10 t 4 pairs of lashing holes in the outer frame, each 5 t (lashing strap attachment) 9 pairs of recessed lashing mushrooms in the outer frame, top and side, each 10 t 2 x front on gooseneck 7 x in lowered bed First lashing eye 250 mm from the front, last max. 250 mm from the rear, spacing not greater than 1,100 mm 3 pairs of additional folding lashing eyes, each 10 t: 1 x on gooseneck (protrudes) 1 x at beginning of low bed, recessed in longitudinal rails 1 x behind the last axle, recessed in the floor Trailer tow device Drawbar with certified 50 mm towing eye Tjdpfx Asrducpsh Ejd Drawbar height adjustable by spring Axles & suspension Drum brake axles, manufacturer's choice Axles/chassis laser aligned—reduces tire and fuel wear Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (equalisation rocking beams) Wheels and tires 235/75 R 17.5" manufacturer's choice Steel rims in twin configuration, factory silver Braking system 2-line compressed air brake system Spring-loaded parking brake 2 foolproof coupling heads at the front with connection leads to tractor unit 24 Volt ABS and ALB, with ABS connector at front, with connecting cable Note: The trailer may only be towed by tractors supporting ABS function! Electrics 12–24 volt, multi-chamber LED lamps, side yellow LED marker lights, LED license plate lights (note: some tractors may show false diagnostics despite correct function) 2 white position lights at the front, LED 2 white/red lane marker lights at the rear, LED 2 x 7-pin foolproof connectors at the front, with connecting cable 1 LED beacon with holder, switched via position light (removable beacon) 2 pairs of warning plates, double LED illuminated and extendable to 3,000mm Floor Gooseneck front with steel/checker plate covering then approx. 70 mm softwood floor, in the wheel arch area steel/checker plate covering Rear bevel with 70 mm softwood floor A

Stanje: novo, največja dovoljena obremenitev: 30.010 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 10.000 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, New vehicle: Fliegl 4-axle low-loader trailer with wheel recesses and split ramps, type VTS 400 RM Lease-purchase offer: Term 48 months, down payment only the VAT, residual value 40% Monthly rate: EUR 899.00 Vehicle / Body: Low-loader First registration: New vehicle Gross weight: 24,000 kg / 40,000 kg Unladen weight: 9,990 kg Payload: 14,010 kg / 30,010 kg Overall length: 12,000 mm Loading length: total approx. 10,000 mm, gooseneck approx. 2,850 mm, load area including rear bevel approx. 7,150 mm Width: 2,550 mm Loading height: 900 mm Further information Low-loader trailer chassis Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear supports Wheel chocks with holders Aluminum side underrun protection Rear spray flap across the entire width Half-shell mudguards on 1st and 2nd axle with anti-spray flaps behind each axle, anti-spray flap behind 4th axle Excavator arm recess above the rear axles, extending to the rear, approx. 1,800 mm long, approx. 650 mm wide, and approx. 150 mm deep 2 pairs of lashing holes (5 t each) in the excavator arm recess, lateral on the main frame approx. 300 mm from the front and approx. 200 mm before the rear bevel Spare wheel carrier for 1 spare wheel, upright on the gooseneck right at the front. Spare wheel, make identical to the main tires, steel rim Storage box recessed in the gooseneck floor with lid; dimensions W = 720 mm / L = 520 mm / D = 170 mm 1st pair of wheel recesses after the gooseneck, recessed in the low-bed lane area, ramped for entry, bottom length approx. 1,600 mm, depth approx. 400 mm. Note: Frame in the main beam area is 400 mm higher than the wheel recess 2nd pair of wheel recesses between the axles, recessed in the low-bed lane area, ramped for entry, bottom length approx. 600 mm, depth approx. 300 mm. Note: Frame in the main beam area is 300 mm higher than the wheel recess Extendable width up to 3,000 mm (not extendable in the rear bevel and not in the lower wheel recesses) (track width of the construction equipment or vehicles to be transported must not exceed the external frame width of 2,550 mm) Storage compartment for wooden planks below the low-bed area 70 mm wooden planks for extension to 3,000 mm Lashing eyes on the low-loader 1 pair of lashing eyes, recessed in the front of the gooseneck, 5 t each 4 pairs of lashing holes in the outer frame, 5 t each (for lashing straps) 8 pairs of lashing rings, integrated on top and side of outer frame, 10 t each 2 at the front on the gooseneck 6 in the low bed First lashing point 250 mm from the front and last max. 250 mm from the rear, spacing between lashing points not greater than 1,100 mm 5 pairs of stake pockets integrated in the outer frame, inside 70 x 40 mm (convertible to 5 t ring lashing eyes, not included) Tjdetrizkspfx Ah Eed 1 pair of folding lashing eyes, additionally recessed in the floor, 10 t each 1 inside next to the main frame at the start of the low bed 2 pairs of additional folding lashing eyes, 10 t each 1 on the gooseneck (protrudes over edge) 1 behind last axle, recessed in floor Drawbar coupling / turntable trailer hitch Towing bar with certified 50 mm towing eye, towing eye inclined 8° D-value at least 160 kN Axles & suspension BPW drum brake axles "Axle/chassis laser alignment" reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical front axle load equalization (rocker balance) Wheels and tires 235 / 75 R 17.5" Manufacturer's choi

Stanje: novo, največja dovoljena obremenitev: 31.920 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 10.410 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, New Fliegl 4-Axle Low Loader Trailer with Ramps, Model VTS 400 Gross weight: 24,000kg / 40,000kg Unladen weight: 8,080kg Payload: 15,920kg / 31,920kg Total length: 11,940mm Total loading length: approx. 10,410mm; Gooseneck: approx. 2,490mm; Loading platform incl. rear bevel: approx. 7,920mm Width: 2,550mm Loading height: 900mm Additional information plus delivery/preparation from stock location 26639 Wiesmoor: €1,280.00 net Leasing offer: term 48 months, down payment only VAT, residual value 40% Monthly instalment EUR 759.00 Chassis Low Loader Trailer Steel welded construction Turntable with heavy-duty ball-bearing slewing ring Foldable rear support 2 wheel chocks with holders Aluminium side underrun protection Full-width rear spray flap Half-shell mudguards on axle 1 + 2 with anti-spray flaps behind each axle Anti-spray flaps before and behind axles 3 and 4 Excavator arm recess over rear axles, stretching to the rear, approx. 1,800mm long, 650mm wide, 150mm deep 2 pairs of lashing holes (5t each) in the excavator arm recess, side-mounted on the longitudinal frame, approx. 300mm from the front and approx. 200mm before the rear bevel 1 plastic toolbox, w=600mm / h=425mm / d=460mm, lockable Storage box recessed into the gooseneck floor with lid, w=720mm / l=520mm / d=170mm Extendable widenings to 3,000mm (not at rear bevel) (Note: the track width of machines or vehicles being transported must not exceed the outer frame width of 2,550mm) Wooden plank compartment under the low-bed platform Tedpfx Ajvv D Ixjh Eod 70mm wooden planks for extension to 3,000mm Low loader lashing points 1 pair of lashing cutouts sunk in the longitudinal beam at the front of the gooseneck, 10t each 4 pairs of lashing holes in external frame (5t each, suitable for tension belt attachment) 9 pairs of lashing mushrooms set into the external frame above and on the sides, each 10t 2x front on gooseneck 7x low-bed area 1st lashing point 250mm from front, last max. 250mm from rear, max distance between lashing points 1,100mm 3 additional pairs of folding lashing eyes, 10t each: - 1x on gooseneck (protruding) - 1x inside start of low-bed area in longitudinal beams - 1x recessed in floor behind last axle Towing arrangement, turntable trailer Drawbar with certified 50mm draw eye Drawbar height adjustment via spring Axles & Suspension Drum brake axles, manufacturer’s choice Chassis/axle laser alignment (reduces tyre wear and fuel consumption) Air suspension with raise & lower valve + auto reset function Wheels and tyres 235/75 R 17.5”, manufacturer’s choice Steel twin wheels, factory silver Braking system 2-line pneumatic brake system Spring-loaded parking brake Axle load detection via EBS CAN-Bus signal (for in-cab display, truck must be pre-equipped, not a calibrated scale) Vehicle stability system 2 foolproof coupling heads at the front, with connecting lines to tractor unit 12-24V EBS (Electronic Braking System) with EBS plug at the front and connecting cable (Knorr brand) Note: Trailer must only be towed by towing vehicles capable of ensuring full ABS functionality! Electrics 12-24V, multi-chamber LED lamps, amber LED side markers, LED license plate lighting (Note: On certain tractor units, malfunction messages may appear even if operational) 2 white position lights at the front (LED) 2 white/red contour marker lights at the rear (LED) 2x 7-pin foolproof connectors at the front