Polpriklopnik z nizko nakladalno ploščadjo

KÄSSBOHRER LB4E EX-1 KK LOWBED Tiefladerauflieger AUSZIEHBA

Stanje: novo, lastna masa: 11.000 kg, največja dovoljena obremenitev: 27.000 kg, skupna masa: 38.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.300 mm, širina tovornega prostora: 2.550 mm, velikost pnevmatike: 235/75 R17.5, barva: siv, obratovalna teža: 11.000 kg, Oprema: ABS, Chassis: - Welded steel frame construction with front and rear frame cranks and a lowered bed without rear chamfer - Neck and kingpin plate 225 mm - Lowered bed rated for 25 t point load over 5 m - Outer frame closed to the outside with welded-on lashing rings for securing - Interchangeable 2" king pin - Rear hook-in rail for aluminum ramps Axles and Tyres: - BPW low-loader axles, each with a 10 t axle load, air bellows diameter 360 mm - Air suspension with lifting and lowering function, stroke 220 mm (-60/+160 mm) - Wabco SmartBoard with ECAS function for 2 coupling heights +100 mm - S-cam brakes 300/200 mm, asbestos-free brake pads - Automatic slack adjusters - IVTM tyre pressure monitoring - 9 tyres 235/75 R 17.5, tubeless Steering: - 1st and 2nd axles hydraulically forced steered via fifth wheel coupling Floor: - Multi-layer bonded board floor, 27 mm thick, flush with outer frame and longitudinal beams Dksdpfx Ajiu Eu Nsl Hol - Underside reinforced with GRP coating - 12 pairs of lashing rings welded in outer frame (8 pairs RUD 8 t – 6 pairs in the lowered bed as well as one pair each on the gooseneck and at the front of the rear aggregate – 2 pairs of 4 t lashing rings on gooseneck and rear aggregate) - 6 pairs of mushroom anchors in outer frame in the lowered bed - Storage box with lid in the lowered bed floor, front left and right Front Wall: - 25 mm aluminum hollow profiles raised up to the lower edge of the roof with integrated tarpaulin tensioning device Sliding Tarpaulins: - Tarpaulin curtains on both sides with integrated vertical and horizontal belts (approx. 600 mm spacing) and stainless steel tension locks - Adjustable tarp straps (overcentre) up to loading width 4,000 mm including tarpaulin extension with press studs and Velcro fastener - Tarp extension in driving direction: 300 mm, in height: 750 mm - Incl. eyelets for separate tarpaulin extension piece - 1 pair of vertical tarpaulin pockets approx. 1,000 mm long, positioned in the lowered bed at the front crank - With belt pockets Rear Wall: - Steel rear portal frame with side tarpaulin hook-in device - Aluminum double-wing door, 25 mm thick - Both door wings fully foldable with door holders - Each door wing with aluminum double-joint hinge and two recessed grip hollows Front Corner Posts: - Roof height, bolted to front side Central Posts: - 3 pairs of infinitely adjustable folding posts - Posts are movable along the entire length via trolley - Middle posts in the lowered bed also fixable at the rear platform Roof: - EDSCHA sliding roof (galvanized) with cross beams movable in both directions (stacked forward inside the cargo area) - Rear portal cross beam swivels away - PVC tarpaulin roof without customs closure - Manually operated hydraulic lifting roof on both sides, lift 450 mm - Movable lifting roof in positions front (9x50) and rear (9x50), can be driven at increased height - Including tarpaulin extension and apron at rear - Roof can be cranked out 900 mm at front wall Accessories: - Extendable warning signs (removable at front and rear, with socket) incl. position lights up to loading width 4,000 mm - Storage for 4 warning signs on inside of front wall, top right and left - 1 aluminum ladder with holder 2,500 mm long on front wall - 2 rows of self-securing aluminum slats - Metal mudguards with splash flaps - 1 overnight parking plate and 1 ADR plate on rear wall - BEKAMAX central lubrication system with pump and grease class 2 for approx. 35 lubrication points - Electrohydraul

Stanje: rabljeno, Leto izdelave: 1988, velikost zadnje pnevmatike: 50%, moč: 59 kW (80,22 KM), stanje pnevmatik: 50 odstotek, Year of manufacture: 1986 to 1990. All machines undergo a complete inspection, are fitted with new batteries, feature the original "Fortschritt" colour scheme, and come with either an E025 cutterbar or E318 windrower. Individual enquiries are welcome! Location: 17094 Pragsdorf. Djdpfx Aloi Ip Hqs Hjkl

Stanje: zelo dobro (rabljeno), konfiguracija osi: 3 osi, prva registracija: 08/1994, barva: rumena, Leto izdelave: 1994, Oprema: ABS, = Additional Options and Accessories = - Air suspension = Further Information = Axle configuration: Rear axle 1: Twin tires Rear axle 2: Twin tires Rear axle 3: Twin tires; Steering Rear axle 4: Twin tires; Steering Weights: Unladen weight: 11,420 kg Functionality: Loading platform height: 77 cm Extendable body: Yes Condition: Technical condition: Very good Visual condition: Very good Djdpfx Ajuxy Dfsl Hokl Financial Information: Price: On request NOOTEBOOM OSD-50-04-V SEMI LOWBED TRAILER 4X SAF AXLES 2X STEERING AXLES (TRAILING) AIR SUSPENDED TIRE SIZE 205/65/R17.5 EXTENDABLE LOADING PLATFORM SIZE 923 CM + 670 CM EXTENDABLE, TOTAL LOADING PLATFORM LENGTH 1,593 CM WIDTH OF LOADING PLATFORM 275 CM + 2X 27.5 CM SIDE EXTENSIONS, TOTAL WIDTH OF LOADING PLATFORM 330 CM HEIGHT OF LOADING PLATFORM ± 77 CM LOADED GOOSENECK LENGTH 388 CM HOOK EYES AND STANCHION POTS 2X REAR SUPPORTS FOLLOW US ON INSTAGRAM: GEURTSTRUCKS WE SPEAK GERMAN HABLAMOS ESPAÑOL WE SPEAK ENGLISH

Stanje: rabljeno, največja dovoljena obremenitev: 40.800 kg, skupna masa: 53.800 kg, konfiguracija osi: 3 osi, prva registracija: 11/2012, naslednji pregled (TÜV): 11/2025, Oprema: ABS, Faymonville 4-osovinski Multimax STN-4AX niskopodni teleskopski poluprikolica Godina proizvodnje: 11.2012 Tara: 13.000 kg Dozvoljena ukupna masa: 53.800 kg Tehnički dozvoljena masa: 55.400 kg Nosivost: 40.800 kg Podpritisna sila: 25.000 kg Dkedpfx Alsu Aynlo Hel Dimenzije guma: 205.65R17,5 3. i 4. osovina – prinudno upravljane 4x SAF osovine 7.600 kg sa vazdušnim ogibljenjem Dužina: 13.475 mm do 20.275 mm (izvlačiva) Širina: 2540 mm do 2620 mm Visina: 1200 mm ! Dodatne informacije na zahtev putem e-maila ! Podaci su informativni i bez garancije na tačnost! Informacije dostupne na internetu su neobavezujući opisi i ne predstavljaju zagarantovane karakteristike. Prodavac ne odgovara za greške, tipografske greške ili greške u prenosu podataka. Zadržavamo pravo na izmene. Stalan otkup i prodaja, kao i zamena i iznajmljivanje dizalica i podiznih vozila, kao i građevinskih i teških vozila.

Stanje: novo, lastna masa: 13.250 kg, največja dovoljena obremenitev: 47.550 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, vzmetenje: zrak, velikost pnevmatike: 245/70 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings 30 mm thick hardwood flooring Dkjdpfxsl Uxdkj Al Hjl Extendable loading platform: Loading platform in extendable design with rear chamfer approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings 3 pairs of outward-folding lashing rings 1 pair of flat lashing rings at the front of the loading area Cut-outs in the outer frame of the loading area for inserting tension straps Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Two-part steel ramps: One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering. Ramp with hydraulically folding and unfolding parts, hydraulic lifting system, and hydraulically adjustable position. Maximum load per pair: 40,000 kg Landing legs: JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced-steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool Tires 245/70 R 17.5 Braking system: Braking system according to EU regulations with EBS-E (4S3M) without connecting lines to tractor unit Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer High-quality one-color two-component (2K) top coat in Novagrau Rear section metallized and painted in RAL 9010 (pure white) Metallic paint not possible Electrical system: Electrical system according to EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connections conforming to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" kingpin One galvanized steel headboard approx. 400 mm high At the galvanized front connection strip, yellow-red air couplings 4 wheel chocks with holders at the headboard One spare wheel with holder in front of the headboard Electro-hydraulic power unit Rear and front remote steering via cable remote control with push-buttons, with single-track control of the axles Bracket at rear of gooseneck for ALU drive-on ramps European reflector signs (red-yellow) at trailer rear White reflective tape according to EU regulations at the sides, at the extension, and red at the rear At the gooseneck and on the ramps left and right, each with a holder for warning signs including socket One holder for beacon at trailer rear Galvanized folding supports under the loading platform chamfer Ramp operating valves fitted on the right side of the trailer Cover plates to bridge the gap between ramps and loading platform One mudflap at trailer rear Manual and description on USB stick Central lubrication system BEKAMAX (Pico) with general-purpose grease NLGI-2 and removable pump guard On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm The rear galvanized stakes are removable, superstructure length approx. 2,560 mm One INOX toolbox 1,350 x 400 x 400 on the gooseneck, box covers oil filler cap 4 pairs of WADER container pockets in the loading area for a

Stanje: novo, največja dovoljena obremenitev: 38.000 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.000 mm, širina tovornega prostora: 2.550 mm, skupna širina: 2.540 mm, skupna višina: 3.780 mm, Leto izdelave: 2026, Oprema: ABS, * Humbaur HTS 30 K * Heavy-duty semi-trailer * Low loader * NEW * Immediately available * Fully galvanized * Robust construction * Overall dimensions: 12,630 mm x 2,540 mm x 3,780 mm * Internal dimensions: 12,000 mm x 2,540 mm * Loading height: 890 mm * Fifth wheel height: 1,230 mm * Fifth wheel platform: 3,500 mm * Low bed: 8,680 mm * Gross weight: 48,000 kg * Payload: 38,000 kg * Tires: 235/75R17.5 * SAF low loader axles with lift and trailing steering axle * Air suspension with raising and lowering function * Twin tires * EBS braking system * 24-volt lighting system * LED side marker lights * Wabco Smart Board * 2-inch kingpin * Chassis frame hot-dip galvanized by immersion * Heavy-duty, welded chassis frame * Climbing strips on ramp incline * 50 mm softwood floor * Recess for excavator stick storage * 3 m equipment package * Steel toolbox under loading platform * Gooseneck with 400 mm front wall * 400 mm high aluminum side boards, foldable * Front storage box with lid * 3 pairs of lashing rings 6 t * 3 pairs of lashing rings 3 t * 5 pairs of lashing rings 10 t * 6 pairs of lashing rings 3 t * 6 pairs of lashing rings 2 t * Ramps with rubber covering * Spare wheel with holder on front wall * LED reversing lights * Visual paint finish on request * Additional equipment options available by arrangement ATTENTION!!!!! PLEASE READ CAREFULLY!!!!! We expressly reserve the right to prior sale, as this item is also offered on other platforms. We strongly recommend inspection and examination so that no misunderstandings arise regarding condition and suitability. Inspections and examinations are possible and expressly welcome by appointment at any time!!! The specified internal dimensions are approximate values. For new vehicles, additional costs for freight and documents may apply. TRADE-INS POSSIBLE FOR ALMOST ANYTHING!!! PART EXCHANGE AND EXTRA PAYMENT POSSIBLE!!! Display area: 58285 Gevelsberg, Am Sinnerhoop 17 Opening hours: Monday to Friday 8:00 am to 5:00 pm, Saturday 8:00 am to 2:00 pm Over 500 new and used trailers in stock at all times!!! Tel.: Fax: Dkeder Ic Rwspfx Al Hsl

Stanje: rabljeno, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2012, * Gigant osi * Zračno vzmetenje * Zadnja krmiljena os * Raztegljiv Dkjdswta Diepfx Al Hol * Lastna teža: 10.920 kg -----Interna številka vozila: 9799----Napake in vmesna prodaja pridržane. WhatsApp podpora na voljo! Za vprašanja o vozilu ali dodatne informacije nam pišite prek WhatsAppa Whatsapp nemščina, angleščina -- Whatsapp nemščina, angleščina, arabščina

Stanje: novo, skupna masa: 80.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Further vehicles available – excerpt from the equipment list. Full equipment details on request. GOOSENECK: * Gooseneck in SNT design for optimized loading bed length, length approx. 3,700 mm, rear with chamfer approx. 1,000 mm x 10° * For tractor units: 4x2, 6x2, and 6x4 * Front steel bulkhead, plug-in, approx. 400 mm high * ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for controlling hydraulic functions (excluding hydraulic winches) * Outer beams of the gooseneck with mounting holes for bolted lashing rings. First hole approx. 200 mm from the front, then approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair horizontal lashing rings at the rear section of the gooseneck (LC 10,000 daN) * On the gooseneck: 1 pair removable ALU side boards approx. 400 mm high, anodized finish * On the gooseneck: 1 removable ALU rear board approx. 400 mm high, anodized finish * Over the gooseneck: approx. 40 mm hardwood flooring, over the king pin checker plate covering * 3.5-inch king pin Dksdpfx Alsxarmaj Hjl * Gooseneck guide plate for the fifth-wheel plate, approx. 500 mm wide * Round NATO socket at the front connection bar (Maeler & Kaege VG 96 917) * 2 pairs of suspended lashing rings with retaining spring on the outer beams of the gooseneck (LC 5,000 daN) LOADING BED: * Loading bed, extendable version, length approx. 8,800 mm with chamfer at the rear approx. 500 mm x 10° * Pneumatic locking with conical locking bolt and reinforced locking positions, supply lines are protected within the extendable beams and automatically adapt to the respective bed length * BPW axles and suspension, first axle hydraulically steered, all other axles hydro-mechanically forced steered * First axle with electro-magnetic reverse lock, activated by reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * 235/75 R 17.5 3PMSF twin tyres – manufacturer at our discretion * Mechanical landing legs with 2-speed gearbox and crank. JOST Modul B – static test load = 50,000 kg * Continuous hardwood flooring (approx. 50 mm thick) on the bed and between axles (interrupted), increasing friction coefficient. – Slots for attachable and adjustable bridging elements * At the front of the bed – 1 movable intermediate table approx. 300 mm wide for the large-section telescopic tube, with checker plate covering. – Front and rear slots for attachable and adjustable bridging elements * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 7 pairs of recessed folding lashing rings on the outer frame of the bed (LC 10,000 daN) * Extensions (galvanized), extendable by approx. 230 mm per side (without wooden planks) * 1 pair mechanical rear supports * Remote-controlled steering from front and rear via cable remote control, with single-track control of axles, without installation in the tractor unit * TPMS tire pressure monitoring sensors installed in all wheels * Locking of the bed with conically welded retaining profiles every 500 mm * Locking control left and right on the trailer * For the intermediate table approx. 300 mm wide, a mechanical lock for securing the table in the extension * 5 pairs of threaded blocks on the extendable beam for mounting M20 screw rings (LC 5,000 daN) BRAKING SYSTEM

Stanje: rabljeno, največja dovoljena obremenitev: 30.380 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 07/2011, Oprema: ABS, Vehicle Identification No.: VAVX99448BH301318 Including ALU ramps – 2,800 mm long, 400 mm wide Unladen weight: 9,620 kg German MOT due Gooseneck: 4,000 mm Low-bed: Length: 8,620 mm Width: 2,550 mm Loading height: 930 mm Removable rails Support legs Dedpfxett U D Do Al Hekl Width extension lighting Max. fifth wheel load at front: 12,000 kg Swing clearance radius: front 2,100 mm - rear 1,900 mm Axle loads (technical): 4 x 7,000 kg BPW Eco Plus axles with drum brakes Axle 1 = liftable Axles 3 + 4 = trailing steered 2 x toolboxes Tyres: 245/70 R 17.5 Changes, prior sale and errors excepted. The description serves for general identification of the vehicle and does not constitute a warranty in the legal sense of sales law. The description in the purchase contract is binding. Our offer is generally without new technical inspection (TÜV). If a new TÜV inspection is required, we are happy to provide an offer from our partner workshops! The vehicle may be covered with advertising stickers and/or inscriptions. Our general terms and conditions of delivery and payment apply.

Stanje: rabljeno, Leto izdelave: 2017, vrsta prenosa: drugo, prva registracija: 01/2017, prevoženi kilometri: 1.001 km, voznikova kabina: drugo, Vehicle location: Bovenden Dsdpfx Aep R Szlsl Hekl Configuration: Rear axle, fire damage! The vehicle had a mileage of approx. 100,000 km! Additional parts are also available for individual sale: - Manual gearbox: €5,000 - Transfer case: €4,500 - Frame: €2,000 Truck VIN: WMA80SZZ7HM729331 ACCESSORY DETAILS WITHOUT GUARANTEE, subject to changes, prior sale, and errors!