Müller-Mitteltal Ka Prikolice nakup rabljenega (249)

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profile 30.0: * EBS braking system * TPMS tire pressure monitoring * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical axle compensation, rear * Side underrun protection * Rear swing-down supports on chassis frame * Mechanically adjustable warning sign packages, front and rear * Front: closed plastic fenders; rear: straight galvanized steel mudguards, each with spray protection * Reflective contour tape, side and rear * Hinged lid (hot-dip galvanized) for toolbox in the turntable platform * Multi-voltage system * LED rear lights * Rotating beacon (removable) at the rear * Tow bar with 40 mm towing eye and height adjustment via draw spring & turnbuckle * 15-pin electrical connector * Four stake pockets per side (stakes not included), each with lashing capability * Load securing package consisting of: 2 lashing eyes (6.4 t) front left & right on the main frame of the turntable platform, 5 pairs of UVV-compliant lashing rings, swiveling and retractable, loadable in all directions and recessed in the outer frame – 13.4 t in the corners, otherwise 10 t * 6 pairs of mechanical fold-out outriggers for 3 m total width (not in the rear taper) * Extension planks stored at the center of the loading area * Excavator arm rest above rear axle up to end cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing eyes on the sides of the excavator arm rest) * Hydraulically one-piece loading ramps (approx. 3,000 x 720 mm) Iodox Ipb Hspfx Ahkotf * Hydraulic lateral ramp shift * Loading area above turntable: approx. 1,960 x 2,520 mm * Loading height unladen: approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Loading height unladen: approx. 910 mm (incl. 860 mm drive-on slope) * Chassis, turntable, tow bar, and ramps hot-dip galvanized * Axles, springs, air tanks, etc., painted in black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * --Permissible total weight of 30,000 kg technically possible-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Subject to errors and prior sale * Available immediately ex works Egestorf near the A7

Stanje: rabljeno, največja dovoljena obremenitev: 17.500 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, prva registracija: 09/2005, naslednji pregled (TÜV): 01/2027, širina tovornega prostora: 2.500 mm, ? Hidravlične rampe ? Razširljive ? 8 pritrdilnih ušes na vsaki strani ? Nosilec za rezervno kolo ? Nakladalna višina: ca. 930 mm ? Bobnasta zavora Itedpfxsytz Hws Ahkef ? Duomatski priključek ? Listnato vzmetenje ? Dvojna kolesa Vse informacije brez jamstva / Možen vmesni prodaj.

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-ER 14.4 Flatbed: ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes ----Axles: * 2 x 7 t BPW axles ----Suspension: * Air suspension with lift and lowering system ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (therefore B-dimension approx. 8,080 mm) * 40 mm flange towing eye ---- Itodpfev D Tbkjx Ahksf Electric / Lighting: * 15-pin electrical connector * LED lighting system 12 / 24 V * 2 additional LED reversing lights at the rear (activated by reverse gear) * 1 removable LED beacon (incl. holder) at the rear * TPMS (Tire Pressure Monitoring System) ----General Attachments: * Mechanically adjustable 3 m warning sign sets front and rear * Landing gear at the front * External folding support legs at the rear * Plastic toolboxes approx. 750 x 350 x 300 mm each, mounted to the left and right sides * Lateral underrun protection * Rear underrun protection * Plastic quarter mudguards ----Loading Platform: * 400 mm high bolted front wall * 50 mm softwood floor * 2 pairs of container locks (extendable for 3 m container external width) and lockable, locking dimension retracted to ISO - DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not DIN compliant) with an absolute external width of 3,000 mm. ----Cargo Securing: * Perforated outer frame, angled at approx. 45 degrees, with 2 t lashing force every 480 mm * Option to fit 3 t drop-in lashing rings every 600 mm - 5 x 3 t UVV lashing rings installed per side - * In each front and rear corner 1 x 6.3 t lashing ring (front directly behind the container locks in the wooden floor and rear in the end cross member) * Various holes in the front and rear cross member for 1.2 t lashing points ----Ramps: * 1 pair of aluminium slide-in ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tyred and tracked vehicles * Storage compartment from the rear, recessed under the loading platform in the chassis ----Paintwork: * ---Chassis, drawbar, front wall, underrun protection and rear supports hot-dip galvanized--- * Axles, air tanks, front landing gear, and flange towing eye painted in black ----Info: * New vehicle with manufacturer warranty * Subject to errors and prior sale ----Delivery time: * Available from week 22/2026

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-ER 14.4 Flatbed: ----Braking system: * EBS (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t BPW axles ----Suspension: * Air suspension with lift and lowering system ----Drawbar / Flange Drawbar Eye: * Height-adjustable drawbar by 300 mm * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (thus B-dimension of approx. 8,080 mm) * 40 mm flange towing eye ---- Electrics / Lighting: * 15-pin electrical connector * LED lighting system 12/24 V * 2 additional LED reversing lights at the rear (switched via reverse gear) * 1 removable LED beacon (incl. bracket) at the rear * TPMS (Tire Pressure Monitoring System) ----General Attachments: * Mechanically adjustable 3 m warning panel sets front and rear * Support windlass at the front * Outward folding support legs at the rear * Plastic toolboxes approx. 750 x 350 x 300 mm each left & right side * Side impact protection * Underrun protection * Plastic quarter mudguards ----Platform: * 400 mm high bolted front wall * 50 mm softwood floor * 2 pairs of container locks (extendable to 3 m container external width) and lockable, locking dimension retracted according to ISO - DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not according to DIN) for an absolute external width of 3,000 mm ----Load Securing: * Perforated outer frame, angled approx. 45 degrees, with 2 t lashing capacity every 480 mm * Optionally, installation of 3 t lashing shackles every 600 mm - each side equipped with 5 x 3 t UVV lashing shackles - * At each front and rear corner, 1 x 6.3 t lashing ring (front directly behind the container locks in the wood floor and rear in the end crossmember) * Various holes for 1.2 t lashing options in the front and rear crossmembers ----Ramps: * 1 pair of aluminium slide-in ramps approx. 3,570 x 410 mm (load capacity 10 t/pair) suitable for rubber-tyred and tracked vehicles * Rear accessible storage compartment underneath the loading platform, integrated in the chassis ----Painting: * ---Chassis, drawbar, front wall, underrun protection and rear supports hot-dip galvanized--- * Axles, air tanks, front support windlass and flange towing eye painted in a shade of black ----Info: * New vehicle with manufacturer's warranty * Subject to errors and prior sale Itsdpfev D Tbdex Ahksf ----Delivery lead-time: * Available from CW 22/2026

Stanje: rabljeno, največja dovoljena obremenitev: 5.900 kg, skupna masa: 9.000 kg, konfiguracija osi: 2 osi, prva registracija: 05/2020, dolžina tovornega prostora: 5.370 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, prostornina tovornega prostora: 5 m³, Oprema: ABS, * ABS * 5-komorna zadnja svetla * Podesivi vučni uređaj po visini * Gigant osovine Iedpjyncyhjfx Ahkstf * Prednji oslonac na navijanje ----Nadgradnja: Niskopodni prikolica, približna visina utovara 870 mm, zadnji deo zakošen, visina uspona približno 780 mm, opružno rasterećene čelične stranice levo i desno, drveno dno, prstenovi i ušice za vezivanje. Opružno rasterećene i bočno pomične rampe za uspon sa vatrootpornim i protivkliznim rešetkastim prečkama od pocinkovanog čelika (dužina cca 2.600 mm), automatska zadnja podrška povezana s upravljanjem rampama, plastična kutija za alat ispred prednjeg zida. Šasija/prednji zid/vučno vratilo/zadnji zid/rampe i stubići pocinkovani. Prodaja isključivo pravnim licima. KOD IZVOZA SE PLAĆA SAMO CENA BEZ PDV-A!!!!! SVE INFORMACIJE BEZ GARANCIJE, POSEBNO OPREMA I DODACI. Osnov za sve kupoprodajne ugovore, fakture, profakture, narudžbine i prodajne razgovore su naši Opšti uslovi poslovanja (vidi Impressum).

Stanje: novo, največja dovoljena obremenitev: 10.660 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 600 mm, Leto izdelave: 2026, * KA-TA-R 14.4: * Wabco EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Tyre pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem equaliser unit * Drawbar height adjustable by approx. 300 mm, with 40 mm flange towing eye * Jost mechanical landing gear at the front * 2 mechanical folding supports at the rear Ijdpfx Ajx Hm Rcshkjtf * Plastic toolbox approx. 750 x 350 x 300 mm on the right-hand side at the front of the chassis * 15-pin power connector * LED taillights 12/24 V * Bolt-on underrun protection * Plastic quarter mudguards * Net hooks at the central lock bearings as well as 2 at the front wall * Chassis made from high-tensile fine-grain steel * Steel pallet 3-way tipper body with reinforced Strong side walls (continuous upper side walls with internal tube reinforcement — without central stanchions — foldable with drop-side spring assistance) * Rear stanchions bolted * Combination steel double-wing rear door, asymmetrically split, can be swung and locked 270°, not foldable, with additional pendulum frame for automatic tailgate opening when tipping, locking via galvanised rotary bar latch at the rear and central locking, deactivation function for automatic rear door operation when tipping in reverse with open wing door * Lashing points: 1 x 5 t per corner and 4 x 3 t per side, integrated in the outer frame * 4 mm floor plate made of fine-grain steel * Rear ramp receiving rail * Reinforced body with load securing certificate * 1 pair aluminium loading ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tyred and tracked vehicles * Lockable rear storage compartment recessed beneath the loading surface in the chassis for ramps * Drawbar, underrun protection, rear stanchion, and rear folding supports hot-dip galvanised * Axles, springs, air tank, and landing gear painted in black * Tyres 358/55 R 19.5 * Sideboard coating in RAL 9010 pure white * Side wall paint in an RAL colour of choice available at extra cost * Errors and prior sale excepted * Available immediately from calendar week 10/2026 * Sample images

Stanje: novo, največja dovoljena obremenitev: 10.660 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 600 mm, Leto izdelave: 2026, * KA-TA-R 14.4: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal—no truck-side installation required * Drum brakes * 2 x 7 ton Gigant axles * Parabolic springs with tandem equalizer assembly * Height-adjustable drawbar (approx. 300 mm) with 40 mm flange towing eye * Jost mechanical landing gear at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm mounted at the front right side of the chassis * 15-pin power connector * LED tail lights 12/24 V * Bolt-on underrun protection * Plastic quarter mudguards * Net hooks in the central locking area as well as 2 on the front wall * Chassis made of fine-grain steel * Steel pallet 3-way tipper body with reinforced Strong sideboards (continuous upper side walls with internal reinforcement tube—without center stanchions—can be folded down with board wall assist spring) * Bolted rear stanchions Itsdpfx Aex Hm Riehkof * Combination steel swing rear doors, 2-wing asymmetrically split, swiveling and lockable up to 270°—not foldable—additionally with pendulum frame for automatic tailgate opening during tipping process, locking via galvanized rotary bar lock at rear and central locking system, deactivation function for automatic tailgate when tipping backwards with opened swing door * Each corner fitted with 1 x 5 ton lashing point and 4 x 3 ton lashing rings on each side, recessed into the outer frame * 4 mm floor plate made of fine-grain steel * Rear guide rail for loading ramps * Reinforced body with load securing certificate * 1 pair aluminum loading ramps approx. 3,570 x 410 mm (load capacity 10 tons/pair), suitable for pneumatic-tyre and tracked vehicles * Lockable storage compartment from the rear, recessed under the loading deck in the chassis for the ramps * Drawbar, underrun protection, rear stanchion, and rear folding supports hot-dip galvanized * Axles, springs, air tank, and landing gear painted in a black tone * Tires: 358/55 R 19.5 * Sideboard paint finish in RAL 9010 pure white * Custom RAL colors for side walls available at extra cost * Errors and prior sale excepted * Immediately available from calendar week 10/2026 * Sample images

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal ETÜ-TA-R 14.4 Tandem | Low Loader | Platform | Trailer Available immediately | Reference number for inquiries: 11611 | Delivery to your address possible * We are happy to provide you with an individual offer * ---- * Gross weight: 14.4 t, Payload: 10.95 t * LED lighting system * GIGANT axles, EBS, twin tires 235/75R 17.5, parabolic springs * Tire pressure monitoring system (TPMS) * 6.27 m x 2.47 m platform with galvanized 400 mm front wall * Excavator bucket rest made of hardwood, bolted to the front wall * Floor height unladen 930 mm / laden 870 mm * One-piece ramps with hot-dip galvanized grid surface, slip-resistant design, retractable down to approx. 20 mm. Secured by retaining bar and diagonal brace * Ramp lifter with upright, adjustable springs for easy one-man operation Itsdpeyndh Hsfx Ahkef * 4 UVV drop lashings (LC 6300 daN) * Perforated outer frame (45°-bent with hole pattern for lashing equipment, lashing force per lashing point LC 2000 daN at a minimum spacing of 480 mm. Installation of drop lashings LC 3000 daN at approx. 600 mm spacing possible), closely spaced cross-stiffeners, high-ribbed front and rear closure with rear loading ramp, hot-dip galvanized * 10 UVV lashing rings LC 3000 daN retractable in the existing hole grid in the outer frame, additional * Additional lashing options via bore holes (Ø 50 mm, LC 1200 daN) in the front and rear crossmembers * Toolbox in front of the front wall * Side marker lights with indicator function * 50 mm thick softwood floor. Chassis hot-dip galvanized * Height-adjustable landing gear at the front, folding supports at the rear * Retrofitting of 2 container locks possible * Drawbar with 40 mm towing eye (hot-dip galvanized), height adjustable, 50 mm eye possible on request * 1 removable LED warning light at the rear * ---- * Leasing, hire purchase, financing, trade-in possible * Example: 510 euros for 60 months’ term, no down payment, no final installment * ---- * Our opening hours: * Monday - Thursday: 08:00 - 17:00 * Friday: 08:00 - 15:00 Outside of business hours, viewings possible by appointment. We speak German, English, Polish, and French Leasing, financing, trade-in possible

Stanje: rabljeno, lastna masa: 3.280 kg, največja dovoljena obremenitev: 14.600 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 09/2013, vzmetenje: zrak, velikost pnevmatike: 265/70 R19,5, medosna razdalja: 5.030 mm, Oprema: ABS, Müller-Mitteltal hooklift trailer | Toolbox | Hot-dip galvanized | Tyres: 265/70R19.5 | BPW disc brakes | TÜV valid until | Subject to errors, input mistakes, and prior sale. Itjdpfx Ajwd Sdcehkjf

Stanje: novo, največja dovoljena obremenitev: 13.410 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 4.995 mm, širina tovornega prostora: 2.380 mm, višina nakladalnega prostora: 900 mm, prostornina tovornega prostora: 11 m³, Leto izdelave: 2026, * Wabco EBS-E (electronic braking system with RSS) * Emergency release device for spring-loaded cylinders * Drum brakes * Tire pressure monitoring system with display option in the truck dashboard via EBS signal (no truck-side installation required) * 2 x 9-ton Gigant axles * Air suspension with ride height control during tipping operation * Drawbar with 50 mm flange-type towing eye (adjustable by +77 mm and -33 mm via offset plate) * Jost landing gear at the front * Foldable galvanized steel underrun protection for paver loading * Closed individual plastic mudguards * Standing platform on the front wall * Manual sliding tarpaulin * 15-pin electrical connector * LED tail lights with galvanized protective cover * Chassis made of high-tensile fine-grained steel * Steel 3-way tipper body (side walls with full-length MM profile, without central stanchion, pendulum-mounted with manual central locking and foldable left-side wall with drop-side spring lift) * Sliding tarpaulin in RAL 7038 agate grey, tarpaulin tensioned with lateral ratchet straps and front/rear tensioning bungees * Front wall platform made of grating with access step at the drawbar and a handrail on the front wall * Rear wall made of HBW 400 steel, pendulum-mounted with automatic two-hook lock * 5 mm steel floor made of HBW 450 steel * 4 x 3-ton recessed and foldable lashing rings per side, embedded into steel floor * Reinforced and certified body according to EN 12642 XL incl. load securing certificate up to 19 tons * Tipping bridge and side walls in RAL 9010 pure white * Sideboard panels painted in RAL 9010 pure white * Painting of side walls in any RAL colour possible at extra cost Iedpfxsxl Nkgs Ahkjtf * Chassis painted in RAL 9011 graphite black * New vehicle with full manufacturer's warranty * Errors and prior sale reserved * Immediately available ex Egestorf

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 02/1992, Leto izdelave: 1992, Oprema: ABS, Müller-Mitteltal Abrollanhänger nemško vozilo = Dodatne informacije = Itsdpext Sd Sjfx Ahksf Lastna masa: 3.140 kg Nosilnost: 14.860 kg Največja dovoljena masa (zGG): 18.000 kg Prodajna cena: € 1.500, US$ 1.733

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 09/1993, Leto izdelave: 1993, Oprema: ABS, = Further Options and Accessories = - Electronic Braking System (EBS) = Remarks = Müller-Mitteltal Low Loader 2-axle low-bed trailer ZSA Drive-on ramps IDNR 892 Ijdpsxt Rw Rofx Ahkotf Transaction process We look forward to advising you and welcome you for contract signing or vehicle collection at our dealership. Please schedule an appointment. If you are unable to visit us in person, we can offer you the complete handling via phone/email/WhatsApp/fax. On request, we deliver your new vehicle directly to your doorstep. This guarantees you the best price, maximum security, and convenience for your transaction. We are also happy to take your used vehicle in part-exchange. We offer the possibility of a digital vehicle appraisal based on your vehicle photos—no dealership visit necessary. Our specialized purchasing team will offer you a guaranteed top price. On request, we can deliver your new used vehicle nationwide directly to your door and take your trade-in vehicle with us. Financing - Leasing Immediate approval and settlement of existing finance Your specialist partner for passenger cars, vans, commercial vehicles and construction machinery ITC GmbH & Co KG Siemensstraße 7 32312 Lübbecke (industrial area) Over 400 vehicles always in stock The information provided in advertisements, on the Internet, price tags, and images are non-binding descriptions and do not constitute guaranteed characteristics. The seller assumes no liability/warranty for typing and data transmission errors. Listed specifications and features should be separately verified. This offer is generally without new TÜV approval; we are happy to provide you with a quotation from our partner workshop. Errors and prior sale excepted. = Further Information = Curb weight: 4,600 kg Payload: 13,400 kg Gross vehicle weight rating: 18,000 kg Sales price: €6,500, US$7,511

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal ETÜ-TA-R 14.4 Tandem Low Loader ? Platform ? Trailer Immediately available | Inquiry No.: 27678 | Delivery to your address possible * We are happy to provide you with an individual offer * ---- * GVW: 14.4t, Payload: 10.95t * LED lighting system * GIGANT axles, EBS, twin tires 235/75R 17.5, parabolic springs * Tire pressure monitoring system (TPMS) * 6.27m x 2.47m platform with galvanized front wall, 400mm high * Excavator bucket rest made of hardwood, bolted to the front wall * Deck height unladen 930mm / laden 870mm * One-piece ramps with hot-dip galvanized grid grating, anti-slip design, can be pushed together to approx. 20 mm, secured by retaining rods and diagonal supports * Ramp lift with vertically mounted, adjustable springs for easy single-person operation * 4 UVV drop lashing rings (LC 6300 daN) * Perforated outer frame (45° angled with hole pattern for lashing equipment, lashing force per point LC 2000 daN with a minimum spacing of 480 mm. Installation of drop lashing rings LC 3000 daN at approx. 600 mm intervals possible) with close cross profiling, high-webbed front and rear closures and rear drive-on slope, hot-dip galvanized * 10 UVV lashing rings LC 3000 daN, retractable into existing hole grid in outer frame, additionally * Further lashing points by drilled holes (Ø 50 mm, LC 1200 daN) in the front and rear crossmember * Toolbox in front of the bulkhead * Side marker lights with indicator function * Softwood floor, 50 mm thick. Chassis hot-dip galvanized * 2 container locks recessed in the front crossmember * Height-adjustable telescopic landing gear at the front, fold-down supports at the rear * Drawbar with 40 mm towing eye (hot-dip galvanized), height adjustable; 50 mm eye available on request * 1 removable LED warning beacon at the rear ---- * Leasing, hire-purchase, financing, trade-in possible * For example: 515 euros at 60 months term, no down payment, no final installment Isdjyadz Repfx Ahkjtf * ---- * Our opening hours * Monday - Thursday: 08:00 - 17:00 * Friday: 08:00 - 15:00 Outside opening hours available by appointment We speak German, English, Polish, French Leasing, financing, trade-in possible

Stanje: novo, največja dovoljena obremenitev: 10.500 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ - TA -R 14.4 Ijdpfx Ahex Ipapjkjtf ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating aggregate ----Drawbar / Drawbar Eye: * Drawbar adjustable in height by 300 mm – drawbar extension by 250 mm to 2,250 mm * 40 mm flanged drawbar eye ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal (no truck-side installation required) * 15-pin power connector * LED tail lights 12 / 24 V * LED rotating beacon (removable) at rear ----General Attachments: * Support winch in front * Externally mounted hot-dip galvanized folding supports at rear * Plastic toolbox approx. 858 x 500 x 500 mm, front right, outside at the front wall * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * Preparation in front of front wall for retrofitting container locks * Bolted front wall made of smooth sheet metal * Sidewalls made of trapezoidal profile steel sheet, foldable with drop-side spring-assisted lifting device * Steel rear wall can be slid between the ramps – storage bracket for unused rear wall inside by the front wall * Rear stanchions bolted * Rear approach angle approx. 860 mm ----Flooring: * 50 mm softwood floor * 12 mm thick and 270 mm wide rubber strips on the inside of ramps * 12 mm thick and 210 mm wide rubber strips on the approach slope and externally on the low-bed platform (from front wall to end sill) ----Load securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Installation of 3 t drop lashing rings every 600 mm possible * 1 x 6.3 t lashing ring at each front and rear corner * Various drill holes in front wall and end sill for 1.2 t lashing options ----Ramps: * One-piece mech. grating ramps with spring system for one-man operation, approx. 2,750 x 870 mm (can be compressed to 20 mm) ----Paintwork: * Chassis, drawbar, front wall, tailgate, and ramps hot-dip galvanized * Axles, springs, air tank, and flanged drawbar eye painted black * Sidewalls painted RAL 9010 pure white ----Info: * --Reinforced and certified body according to EN 12642 XL incl. load securing certificate-- * Errors and prior sale excepted * New vehicle with manufacturer’s warranty ----Delivery time: Vehicle is immediately available

Stanje: novo, največja dovoljena obremenitev: 10.500 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * First inspection (ETÜ) - TA -R 14.4 ----Brake System: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with equalizing unit ----Drawbar / Flange Eye: * Height-adjustable drawbar by approx. 300 mm - drawbar extension by 250 mm to 2,250 mm total length * 40 mm flange-type towing eye ----Electrics / Lighting: * Tire pressure monitoring with display option in the truck via EBS signal (without truck-side installation) * 15-pin electrical connector * LED rear lights 12 / 24 V * Removable LED beacon at rear ----General Attachments: * Landing leg at the front * Externally mounted hot-dip galvanized folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, externally mounted on the front right end wall * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * Preparation in front of the bulkhead for later installation of container locks * Bolted smooth steel bulkhead * Foldable steel side walls with trapezoidal profile, with drop-side spring assist * Removable steel rear wall, stowable inside at the front of the bulkhead when not in use * Bolted rear stanchions * Rear ramp bevel approx. 860 mm ----Flooring: * 50 mm softwood flooring * 12 mm thick and 270 mm wide rubber strips on the inside of the loading ramps * 12 mm thick and 210 mm wide rubber strips on the ramp bevel and on the exterior of the low loader platform (from front bulkhead to rear cross member) ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Possible installation of 3 t folding lashing rings every 600 mm * 1 x 6.3 t lashing ring in each of the front and rear corners * Various drillings in the front and rear cross members for 1.2 t lashing options ----Ramps: Isdpfx Ahsx Ipbajketf * One-piece mechanical grating ramps with spring assistance for single-person operation, approx. 2,750 x 870 mm (collapsible to 20 mm thickness) ----Paint Finish: * Chassis, drawbar, front wall, tailgate, and ramps hot-dip galvanized * Axles, springs, air tanks, and flange eye painted in black * Side walls painted in RAL 9010 pure white ----Information: * Reinforced and certified superstructure according to EN 12642 XL, including load securing certificate * Subject to errors and prior sale * New vehicle with manufacturer’s warranty ----Delivery time: Vehicle is immediately available ex Eggerstorf

Stanje: novo, največja dovoljena obremenitev: 10.900 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, ETÜ-TA-R 14.4 ----Brake System: * EBS electronic braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Air suspension ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm up to 2,250 mm * 40 mm flange towing eye ----Lighting / Electrical: * TPMS (Tire Pressure Monitoring System) * LED tail lights 12 / 24 V * 15-pin power connector ----General Attachments: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding supports at the rear * Plastic toolbox mounted externally at the front right on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: Itedoq Dyvyspfx Ahkjf * 50 mm softwood floor * Preparation in front of the bulkhead for retrofitting container locks * Bolted smooth sheet metal bulkhead * Trapezoidal-profiled, fold-down steel side walls with drop-side spring assists * Steel rear wall, can be stowed between the ramp holders when not in use, inside in front of the bulkhead * Bolted rear stanchions * Rear drive-on slope approx. 860 mm ----Load Securing: * Perforated outer frame, edged at approx. 45 degrees with 2 t lashing capacity every 480 mm * Installation of 3 t fold-down lashing rings possible every 600 mm * 1 x 6.3 t lashing ring at each front and rear corner * Various holes for 1.2 t lashing options in bulkhead and rear crossmember ----Ramps: * One-piece mechanical grating drive-up ramps with spring mechanism for one-man operation, approx. 2,750 x 600 mm (collapsible down to 20 mm) ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, bulkhead, rear wall, tailgate, and drive-up ramps * Side wall color in RAL 9010 pure white * Painting of side walls in any RAL color available at extra cost ----Info: * — Reinforced and certified body according to EN 12642 XL including load securing certificate — * New vehicle with manufacturer warranty * Errors and prior sale excepted ----Delivery time: * Immediately available ex Egestorf

Stanje: rabljeno, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 02/2021, naslednji pregled (TÜV): 08/2026, dolžina tovornega prostora: 4.800 mm, širina tovornega prostora: 2.430 mm, višina nakladalnega prostora: 500 mm, Oprema: ABS, Müller-Mitteltal nizkopodni kesonski priklopnik - Nizkopodni in dvosmerni kesonski priklopnik v enem vozilu - Vlečno uho 40 mm - Pnevmatski zavorni sistem - Podporna stojala za nakladanje in razkladanje - Gigant osi - Pnevmatske gume: 235/75 R 17,5 - Bobnaste zavore - Lastna teža: 3.620 kg Ijdpeyk Rfkofx Ahkjtf - Nastavljiva višina drogov - TÜV veljaven do: 08.2026 - SP veljaven do: 02.2026 - SP veljaven do: - Dolžina tovornega prostora: 4.800 mm - Širina tovornega prostora: 2.430 mm - Višina stranic: 0,5 m Pridržujemo si pravico do napak in vmesne prodaje. Interna številka vozila: 11349.

Stanje: novo, največja dovoljena obremenitev: 13.490 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, TRA-Kombi 18.0: 3-in-1 = for hook-lift containers, skip containers, and as a low loader ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 10.5 t axles ----Suspension: * Air suspension with manual lowering at rear ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm towing eye and height adjustment ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System), display possible in the truck via EBS signal (no truck-side installation required) * LED tail lights 12 / 24 V * 15-pin electrical connector ----General Attachments: * Tool box made of powder-coated sheet steel * Spare wheel holder in basket design on the right side * Closed side underrun protection * Plastic 1/4 mudguards with splash protection * Plastic rear impact bumpers * Foldable "A" sign rear plate ----Loading Area: * Hot-dip galvanized main frame with raised outer frame for guiding rolling containers * Steel sheet floor with roll recesses in the bogie area Itedpfx Aol Tld Iohkof * For hook-lift container transport: container length from 5,500 to 7,000 mm possible * Pneumatic 4-point locker and mechanically plug-in front stops in the runway * Transport of up to 2 skip containers with max. 10 m³ volume possible * Includes 8 repositionable container stops for lateral centering, front 4 stops with swiveling shackle * Weld bead as anti-slip surface in the inclined entry area * Mechanical rear landing supports ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning devices for positive and force-fit securing, with 4 cloverleaf-style lashing brackets on each side * 1 pair of 13.4 t UVV lashing rings at the front * On each side, 4 x 8 t lashing eyes recessed into the outer frame ----Ramps: * Aluminium approach ramps (10.6 t / pair), 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable rear storage compartment) ----Paintwork: * Reflective contour tape on sides and rear * Frame hot-dip galvanized * Axles and drawbar painted black ----Info: * Load securing certificate according to DIN 30722-1 * Load securing certificates according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * --Permissible total gross weight technically possible: 20,000 kg-- * New vehicle with factory warranty, no initial registration * Errors and prior sale excepted ----Delivery time: * Available immediately ex Egstorf

Stanje: novo, največja dovoljena obremenitev: 13.490 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, TRA-Kombi 18.0: * 3-in-1 solution: suitable for roll-off containers, skip containers, and as a low-loader ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 10.5 t axles ----Suspension: * Air suspension with manual lowering at the rear ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long with 40 mm towing eye and height adjustment device ----Electrical / Lighting: Ijdpfx Ahewb Rakekstf * Tire pressure monitoring system (TPMS), display capability in truck via EBS signal (no truck-side installation required) * LED rear lights 12/24 V * 15-pin power connector ----General Attachments: * Tool box made of powder-coated sheet steel * Spare wheel carrier (basket type) on the right side * Closed side underrun protection * Plastic quarter mudguards with splash protection * Plastic rear impact protection buffers * Foldable A-sign at the rear ----Loading Platform: * Hot-dip galvanized main frame with raised outer frame for guiding roll containers * Steel deck with recessed rollers in the bogie area * Can transport roll-off containers with a container length of 5,500 – 7,000 mm * Pneumatic 4-point clamp locking and mechanical plug-in stop angles at the front of the guide track * Transport of up to 2 skip containers with a max. volume of 10 m³ possible * Includes 8 repositionable bin stops for lateral centering of the skips, front 4 stops plug-in with pivoting stop * Weld bead as anti-slip coating in the ramp area of the track * Mechanical drop-down supports at the rear ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the side for securing with tensioning elements, 4 cloverleaf-type lashing brackets per side * 1 pair of 13.4 t UVV lashing rings to the front * 4 x 8 t recessed lashing eyes per side in the outer frame ----Ramps: * Aluminum loading ramps (10.6 t/pair) 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Paintwork: * Reflective contour tape on sides and rear * Frame hot-dip galvanized * Axles and drawbar painted black ----Additional Information: * Load securing certificate according to DIN 30722-1 * Load securing certificates according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * --Permissible gross weight of 20,000 kg technically possible-- * New vehicle without initial registration, with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available from Egstorf

Stanje: novo, največja dovoljena obremenitev: 13.490 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, TRA-Kombi 18.0: 3 in 1 = suitable for hooklift containers, skip containers, and as a low-bed trailer ----Braking System: * EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10.5 t axles ----Suspension: * Air suspension with manual rear lowering ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm tow eye and height adjustment device ----Electrical / Lighting: * TPMS (Tire Pressure Monitoring System), display capability in the truck via EBS signal (no truck-side installation required) * LED tail lights, 12 / 24 V * 15-pin power connector Itodpfol Tnwzsx Ahksf ----General Attachments: * Tool box made of powder-coated sheet steel * Spare wheel holder, basket design, right side * Enclosed side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear impact protection buffer * Folding A-sign at the rear ----Loading Platform: * Hot-dip galvanized main frame with raised outer frame to guide roll-off containers * Steel sheet floor with roller recesses in the bogie area * When transporting roll-off containers: container length from 5,500 - 7,000 mm possible * Pneumatic 4-point container locking system and mechanically lockable stop angles at the front of the track * Transport of up to 2 skip containers with max. 10 m³ capacity possible * Includes 8 repositionable skip stops for lateral centering, the front 4 are plug-in with pendulum-mounted stops * Weld bead as anti-slip surface in the inclined ramp area * Mechanical rear drop supports ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning elements for positive and non-positive securing of skips, 4 lashing brackets each (shamrock design) on the sides * 1 pair of 13.4 t UVV lashing rings forward * 4 x 8 t lashing eyes recessed in the outer frame on each side ----Ramps: * Aluminum loading ramps (10.6 t / pair) 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Painting: * Reflective contour markings, sides & rear * Frame hot-dip galvanized * Axles, drawbar painted black ----Information: * Load securing certificate according to DIN 30722-1 * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 * --Permissible gross weight of 20,000 kg technically possible-- * New vehicle without initial registration, with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex Egstorf

Stanje: novo, največja dovoljena obremenitev: 10.900 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, ETÜ-TA-R 14.4 ----Braking System: * EBS Electronic Braking System * Emergency release mechanism for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Air suspension ----Tow Bar / Flange Towing Eye: * Height-adjustable tow bar, adjustable by 300 mm * Tow bar extension by 250 mm to a total of 2,250 mm * 40 mm flange towing eye ----Lighting / Electrics: * Tire pressure monitoring system (TPMS) * LED rear lights 12 / 24 V * 15-pin power connector ----General Attachments: * Jost landing gear at the front * Externally mounted hot-dip galvanized folding supports at the rear * Plastic toolbox on the front right side of the headboard * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood floor * Preparation in front of the headboard for retrofitting container locks * Bolted headboard made of smooth sheet metal * Trapezoidal profiled drop-side walls made of steel, foldable with drop-side spring assist * Steel rear wall insertable between ramp mounts; when not in use, stowed inside in front of the headboard * Bolt-on rear posts * Rear approach angle approx. 860 mm ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Possible installation of 3 t drop lashing rings every 600 mm * One 6.3 t lashing point in each front and rear corner * Various holes in the front and rear cross member for 1.2 t lashing options ----Ramps: * One-piece mechanical grid ramps with spring assistance for single-person operation, approx. 2,750 x 600 mm (can be telescoped down to 20 mm) ----Painting: * Hot-dip galvanized chassis as well as tow bar, headboard, rear wall, tailgate, and ramps * Side wall color RAL 9010 pure white * Painting of side walls in a RAL color of choice available at extra cost ----Information: * --Reinforced and certified body according to EN 12642 XL incl. load securing certificate-- * New vehicle with manufacturer’s warranty * Subject to errors and prior sale Itsdpfx Aepk Dv Rjhkof ----Delivery Time: * Available immediately ex works Egestorf

Stanje: rabljeno, konfiguracija osi: 2 osi, Leto izdelave: 2014, Oprema: ABS, Za vprašanja o vozilu vam je na voljo g. Seidel (po telefonu). MÜLLER MITTELTAL SF32BM/BT Mešalni polpriklopnik za beton Nadgradnja: Liebherr HTM 1004 10m³, BPW osi, bobnaste zavore, zavorni vzmeti, Wabco ABS, 1. os dvižna, zračno vzmetenje, dovoljena skupna masa: 32.000 kg, lastna masa: 6.510 kg, nosilnost: 25.490 kg, profil pnevmatik: 1. os 14-15 mm, 2. os 10 mm Po želji vam pripravimo ponudbo za leasing ali financiranje. G. Seidel (tel.) vas z veseljem svetuje. Več informacij najdete na naši spletni strani. ... Pridržujemo si pravico do napak, sprememb in vmesne prodaje!!! Isdpfx Ahoyfu Sdekotf = Dodatne informacije = Dovoljena skupna masa: 32.000 kg Zunanje mere: 0x2500x4000 Za dodatne informacije kontaktirajte Tobias Ebert.

Stanje: novo, največja dovoljena obremenitev: 37.390 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Start-up aid for maneuvering purposes switched to the first axle via EBS (no installation required on the truck side) * Rear axle as self-steering axle with electro-pneumatic steering lock * Locking of the self-steering axle from the driver's cab for maneuvering purposes, controlled via EBS (no installation required on the truck side) ----Suspension: * Air suspension with lifting/lowering device and Ride-to-Return valve Iedpfx Ahjq Euakjketf ----Electrics / Lighting: * Smart Board mounted on the trailer as an information tool with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12/24 V * LED rotating beacon (removable) at the rear * 2 additional LED reversing lights * 7-pin socket at rear for extended length lighting * Side marker lights with indicator signal control * Tyre pressure monitoring system with display option in the truck via EBS signal (no installation required on the truck side) ----General equipment: * Side underrun protection * Landing gears at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the front wall crossmember (without spare wheel) * Mechanically adjustable warning sign packages at front and rear * Swing arm as carrier for connecting cables from truck to semi-trailer ----Low loader deck: * 2nd king pin position * Fifth wheel platform with 45° chamfered front corners and front tool box made of galvanized powder-coated sheet steel B = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm high aluminium side boards (in RAL colour of choice) on the sides of the fifth wheel platform, foldable and removable * Rear wall -150 mm- high plug-in * Rear slope on fifth wheel platform to low bed approx. 700 mm long with tread plate covering and at the end a perforated strip for attaching aluminium loading ramps * Fifth wheel platform with 50 mm clamped wooden planks and low bed platform with 60 mm clamped wooden planks * Tear plate above the axles * 9 x mechanical folding extensions to 3 m overall width, but not in the rear slope (extension planks available with closed storage compartment across the direction of travel under the loading floor) * 3 mounting shafts under the fifth wheel platform for storage of optional aluminium loading ramps or wooden planks for wheel well coverings ----Load securing (LaSi package): Fifth wheel platform: * Perforated outer frame angled at 45° with hole pattern for lashing points (2 t lashing capacity per point at a minimum spacing of 480 mm) * 3 x 13.4 t lashing rings each side recessed in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal beams after the drop, 1 x above the centre axle next to the longitudinal beam) Low loader platform: * 3 x 13.4 t lashing rings each side on the outer frame (1 x beginning of the drop on the fifth wheel platform, 1 x beginning of the ramp slope, 1 x end of the ramp slope) * 2 x 10 t lashing rings each side (1 x between front wheel well and 1st axle, 1 x between 2nd and 3rd axle) * 3 x 5 t lashing rings each side bolted to the outer frame of the wheel wells (2 on the front wheel well, 1 on the rear wheel well) ----Excavator arm recess: * Extended excavator arm recess from end of last fixed axle through to steering axle up to rear crossmember, continuous with

Stanje: novo, največja dovoljena obremenitev: 36.900 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 ton BPW axles * Start assist for shunting purposes on the first axle, activated via EBS (without truck-side installation) * Last axle is a trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle for maneuvering purposes from the driver’s cab via EBS (without truck-side installation) ----Suspension: * Air suspension with lift and lowering function as well as RtR valve ----Electrics / Lighting: * Smart-Board infotool mounted on trailer with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear * 2 additional LED reversing lights * 7-pin socket at rear for overlength lighting * Side marker lamps with indicator function * Tire pressure monitoring with display in the truck via EBS signal (without truck-side installation) ----General Attachments: * Side underrun protection * Support legs at the front and swing-down supports at the rear of the chassis * Straight steel mudguards Iedpfjykx Nkjx Ahketf * Spare wheel holder in front of the front wall crossmember (without spare wheel) * Mechanically adjustable warning sign packages front and rear * Swing arm as a carrier for connecting lines from truck to semi-trailer ----Low Loader Platform: * 2nd king pin position * Gooseneck platform with 45° chamfered front corners and front-mounted toolbox made of galvanized, powder-coated sheet steel B = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm aluminum side boards (in desired RAL color) foldable and removable along the gooseneck platform * Rear wall, insertable, height 150 mm * Rear incline on the gooseneck platform to the low-bed approx. 700 mm long with checker plate covering and at the end a perforated strip for attaching aluminum approach ramps * Gooseneck platform with 50 mm clamped wooden planks, low-bed platform with 60 mm clamped wooden planks * Tread plate over axles * 9 mechanical extension panels to a total width of 3 m, not included in the rear incline (extension planks available with closed transverse stowage compartment under load floor) * Preparation for 3 storage recesses under the gooseneck platform for optional storage of aluminum approach ramps or planks for covering wheel recesses * Preparation for container locks on the swan neck ----Load Securing (LaSi Package): Gooseneck platform: * Perforated outer frame, 45° angled, with hole pattern for lashing devices (2 t lashing capacity per point with a minimum spacing of 480 mm) * 3 x 13.4 t lashing rings recessed into the floor per side (1 x on gooseneck platform, 1 x on longitudinal frame after the cranking, 1 x above middle axle next to longitudinal frame) Low-bed platform: * 3 x 13.4 t lashing rings per side at the outer frame (1 x start of gooseneck cranking, 1 x start of approach ramp, 1 x end of approach ramp) * 2 x 10 t lashing rings per side (1 x between front wheel recess and 1st axle, 1 x between 2nd and 3rd axle) * 3 x 5 t lashing rings per side screwed to outer frames of the wheel recesses (2 at front wheel recess, 1 at rear wheel recess) ----Excavator Arm Rest: * Extended excavator arm rest from end of last rigid axle over the steering axle to the end cross member, continuous with internal reinforcing profile approx. W = 770 mm x T rear

Stanje: novo, največja dovoljena obremenitev: 36.900 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: Iodpfx Ahsykx Nqekjtf * 3 x 11 t BPW axles * Moving-off aid for shunting, connected to the first axle via EBS (no installation required on the truck side) * Last axle as self-steering trailing axle with electro-pneumatic lock * Trailing axle lock for shunting purposes, activated from the cab via EBS (no installation required on the truck side) ----Suspension: * Air suspension with lifting and lowering system, including RtR valve ----Electrics / Lighting: * Smart-Board infotool mounted on trailer with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear * 2 additional LED reversing lights * 7-pin socket at rear for overlength lighting * Side marker lights with indicator circuit * Tire pressure monitoring with display in the truck via EBS signal (no installation required on the truck side) ----General Attachments: * Side underrun protection * Landing gear at front, swing supports at rear of the chassis * Straight steel fenders * Spare wheel carrier in front of front wall crossmember (spare wheel not included) * Mechanically adjustable warning sign packages at front and rear * Swing arm as carrier for connection lines from truck to trailer ----Low Loader Deck: * 2nd kingpin position * Saddled platform with 45° chamfered front corners and front toolbox made from galvanized, powder-coated steel sheet (W = 2,480 x H = 500 x L = 665 mm) with folding lid * 400 mm high drop-down/removable aluminium sideboards (custom RAL color) on saddle platform * Removable 150 mm high rear wall * Rear inclined ramp of approx. 700 mm at the end of saddle platform to low-bed deck, fitted with checker plate and lashing bar for attaching aluminium approach ramps * Saddle platform with 50 mm tongued-and-grooved timber floor, low-bed platform with 60 mm tongued-and-grooved timber planks * Tread plate above axles * 9 x mechanical folding extensions to 3 m overall width, but not on rear ramp (extension planks included with lockable transverse storage compartment under load area) * Preparation for 3 ramp storage compartments under saddle platform for either aluminium ramps or timber planks for wheel trough covers * Preparation for container locks on the gooseneck ----Load Securing (LaSi Package): Saddle Platform: * Perforated external frame, angled at 45°, with hole pattern for lashing equipment (2 t lashing capacity per point, minimum spacing 480 mm) * 3 x 13.4 t recessed tie-down rings per side (1 on saddle platform, 1 on main longitudinal beams after the step, 1 above the center axle beside the beam) Low-bed Deck: * 3 x 13.4 t tie-down rings per side on outer frame (1 at the start of the gooseneck, 1 at the start of the rear ramp, 1 at the end of the ramp) * 2 x 10 t tie-down rings per side (1 between front wheel-well and 1st axle, 1 between 2nd and 3rd axle) * 3 x 5 t tie-down rings per side, bolted to the outer frame of wheel wells (2 at front, 1 at rear wheel well) ----Digger Arm Rest: * Extended digger arm rest from end of last fixed axle over steering axle to end crossmember, continuous with internal reinforcement profile, approx. W = 770 mm x D at rear