Müller-Mitteltal Ka Prikolice nakup rabljenega (250)

Stanje: novo, največja dovoljena obremenitev: 30.080 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – without truck-side installation * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning panel packages front & rear * SmartBord infotool installed with pressure sensors for total axle load display per axle group * Reflective contour tape on the sides and rear * LED rotating beacon (removable) at the rear Hnsdpfx Aoxmpydji Aek * 15-pin power connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front closed single plastic mudguards * Straight rear steel mudflaps, each with spray suppression * Side underrun protection * Superstructure in front of the bogie platform approx. 520 mm with 45° corners and 3 storage compartments including lockable folding lids (folding lids opening to the rear) * Chassis made from high-strength fine-grained steel * Floor over the bogie platform made of 50 mm softwood, and 60 mm softwood in the low loader platform * Outer planks of the drive-on ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing eyes 6.4 t front left and right on the main frame of the bogie platform, 1 pair each of 13.4 t lashing rings at the front and rear outer frame, 1 pair each of 10 t lashing rings, swiveling and lowerable, loadable in all directions and recessed in the outer frame, 5 t lashing rings bolted to the outer frame of the wheel recesses (2 at the front recess, 1 at the rear), 2 pairs of 6.4 t lashing rings on the excavator stick holder * 11 pairs of folding outriggers for a total width of 3 meters (not at the rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for the widening boards made of sheet steel, mounted transversely to the loading area in front of the first rear axle * Excavator stick holder above the rear axle up to the end of the approach slope approx. 2,300 x 740 x 190 mm * Two wheel recesses per side approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with retractable cover (storage for covers at the front on the bogie platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm * Hydraulic lateral ramp shift * Loading area over the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loading height loaded approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, bogie, folding outriggers, rear drop-down supports, and drive-on ramps galvanised * Axles, air tanks, and drawbar painted in black * Tires: 235/75R17.5 * Vehicle is galvanised * New vehicle with manufacturer’s warranty * Errors and prior sale reserved * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 30.080 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning sign packages front & rear * SmartBord infotool installed with pressure sensors for displaying axle group loads * Reflective contour tape on the sides and rear * LED beacon (removable) at the rear * 15-pin electrical connector * LED tail lights Hnedpfjxmpykjx Ai Aek * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front enclosed individual plastic mudguards * Rear straight steel mudflaps with spray suppression * Side underrun protection * Extension in front of the bogie platform approx. 520 mm with 45° corners and 3 storage compartments with lockable folding lids (folding lids open towards the rear) * Chassis made from high-strength fine-grain steel * Floor over bogie platform made of 50 mm softwood, and in the low-bed platform made of 60 mm softwood * Outer planks of the ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing eyes 6.4 t each at the front left and right on the main frame of the bogie platform; one pair of 13.4 t lashing rings at the front and rear sides of outer frame; one pair of 10 t lashing rings on each side foldable and lowerable, loadable in all directions, integrated into the side frame; 5 t bolted lashing rings on the outer frame of the wheel recesses (2 per front wheel recess, 1 per rear); 2 pairs of 6.4 t lashing rings at the excavator stick compartment * 11 pairs of fold-out outriggers for overall width of 3 m (not on the rear incline) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for width-extension planks, steel, mounted crosswise to the loading area in front of the first rear axle * Excavator stick compartment above the rear axle extending to the end of the ramp incline, approx. 2,300 x 740 x 190 mm * Two wheel recesses per side approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with retractable cover (storage for covers at the front on bogie platform) for transporting wheel loaders with wheelbase 3,100 – 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulic extendable tip, approx. 4,650 x 720 mm * Hydraulic sideward ramp displacement * Loading area above the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded deck height approx. 890 mm ± 20 mm (including 860 mm ramp incline) * Chassis, bogie, fold-out outriggers, rear supports, and access ramps fully hot-dip galvanized * Axles, air tanks, and drawbar painted in black shade * Tires: 235/75R17.5 * Vehicle is fully hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 13.600 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2026, * KA-TA-RT 18.0: ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Suspension: * Air suspension with lifting and lowering system, including RtR valve and manual lowering function for loading operations ----Drawbar / Flange Towing Eye: * Drawbar with positive-locking height adjustment * 50 mm flange towing eye ----Electrics / Lighting: * 15-pin 24 V electrical system * LED tail lights 12 / 24 V integrated in underrun protection ----General Fitted Components: * Landing gear at front * External folding supports at rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted on right side * Plastic quarter mudguards ----Tipper Body: * Steel pallet 3-way tipper body made of high-strength fine-grained steel with high M-Strong side walls and reinforced 180 bar tipping cylinder * Fixed front wall made of smooth sheet metal * Hardwood pad for excavator bucket bolted to the front wall * Continuous side walls – without central stanchion – folding with board spring lifters and manual central locking with swinging function * Screwed-in rear posts * Combination steel double-wing tailgate, asymmetrically split, swivels and locks up to 270°, not foldable, with additional swing frame for automatic tailgate opening during tipping; locking via galvanized rod latch and central locking, deactivation function for automatic tailgate opening when tipping backwards with open wing door * 4 mm steel-sheet floor * Two-step entry, front left * Rear track rail for loading ramps ----Load Securing: Hjdsvin T Sopfx Ai Ajnk * 1 x 7 t lashing ring in each corner * 4 x 3 t lashing eyes recessed in the side external frame ----Loading Ramps: * Recessed compartment for loading ramps at rear in the chassis * 1 pair of aluminium loading ramps (10 t / pair) approx. 3,570 x 410 mm, suitable for rubber-tyred and tracked vehicles ----Paintwork: * Chassis, drawbar, rear posts, front wall, tipper body, underrun guard, rear folding supports hot-dip galvanized * Side walls – KTL-coated – and tailgate painted in RAL 9010 pure white * Side walls in other RAL colours available at extra cost * Axles, air tanks, flange towing eye, front landing gear painted in black tone ----Information: * Load securing certificate according to EN 12642 XL? * Errors and prior sale excepted * Sample images (actual vehicle photos may vary due to special equipment) ----Delivery time: * Available from calendar week 15 / 2026

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 04/2005, barva: črn, Leto izdelave: 2005, Oprema: ABS, = Further options and accessories = - Spare wheel - Twin tyres = Remarks = Müller Mitteltal 2-axle T5 2AL low-loader with ramps Air suspension BPW axles ABS ZSA Tyres 60% GR 235R17.5 ID No. 665 We look forward to welcoming you for consultation, contract signing or vehicle collection at our dealership. Please arrange an appointment in advance. If you are unable to visit us in person, we offer complete processing via phone/email/WhatsApp/fax. Upon request, we can deliver your new vehicle directly to your door. This means the best price, maximum security and convenience when purchasing your vehicle. Trade-in We are happy to accept your used car as a trade-in. We offer a digital vehicle appraisal based on your vehicle photos, even without a dealership visit. Our specialised purchasing team guarantees you the highest possible price. Upon request, we will deliver your new 'pre-owned' vehicle nationwide directly to your door and take back your used car. Financing - Leasing Immediate approval and takeover of existing loans. Your specialist partner for passenger cars, vans, commercial vehicles and construction machinery ITC GmbH & Co KG Siemensstraße 7 Hnedpfx Aisxw T Uas Ajk 32312 Lübbecke (industrial estate) Visit our website at Over 400 vehicles in stock at all times The information provided in advertisements, on the internet, price tags and images is non-binding and does not constitute warranted characteristics. The seller assumes no liability or guarantee for typing errors or data transmission mistakes. Listed equipment should be verified separately if necessary. The offer is generally without new general inspection (TÜV); we would be happy to quote for inspection via our partner workshop. Subject to error and prior sale. = Further information = Unladen weight: 8,900 kg Payload: 26,100 kg Gross vehicle weight: 35,000 kg Sales price: €18,000, US$20,770

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 03/2004, Leto izdelave: 2004, Oprema: ABS, = Additional options and equipment = - Electronic Braking System (EBS) = Notes = Müller-Mitteltal RAK German vehicle Roll-off trailer 2-axle Air suspension ABS Tyres 60% ID no. 709 We look forward to advising you, signing contracts, or handing over the vehicle at our dealership. Please make an appointment. If you are unable to visit our showroom, we offer complete processing by phone, email, WhatsApp, or fax. On request, we deliver your new vehicle directly to your door. This means you get the best price as well as maximum safety and convenience with your purchase. We are happy to take your used vehicle as a trade-in. We offer you the option of a digital vehicle appraisal based on your vehicle photos, even without visiting the dealership. Our specialised purchasing team offers you a guaranteed top price. Upon request, we deliver your new ‘used’ vehicle nationwide directly to your doorstep and take your trade-in back with us. Financing – leasing Immediate approval and settlement of existing loans. Your specialist partner for passenger cars, vans, commercial vehicles, and construction machinery. ITC GmbH & Co KG Siemensstraße 7 32312 Lübbecke (industrial area) Over 400 vehicles in stock at all times. The information given in advertisements, on the internet, on price labels, and in pictures are non-binding descriptions and do not constitute guaranteed characteristics. The seller assumes no liability/warranty for typing or data transmission errors. Listed equipment may need to be checked separately by the buyer. Offer is generally without new TÜV approval; we will gladly provide you with an offer from our partner workshop. Subject to errors and prior sale. = Further information = Unladen weight: 4,850 kg Hedpfxjxyx Hao Ai Asnk Payload: 13,150 kg Gross vehicle weight: 18,000 kg

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 08/1996, Leto izdelave: 1996, Oprema: ABS, = Additional Options and Equipment = - Electronic Braking System (EBS) = Remarks = Müller-Mitteltal Trailer ATL Roll-off trailer 2-axle Air suspension ABS Tyres 60% Information available in German We look forward to advising you Contract signing or vehicle collection at our dealership. Please arrange an appointment If you are unable to visit our dealership in person, we offer complete processing via telephone/email/WhatsApp/fax On request, we can deliver your new vehicle directly to your door This means best price for you, maximum security and convenience during acceptance We are happy to accept your used vehicle as part-exchange We offer the option of digital vehicle evaluation based on your vehicle photos even without a dealership visit Our specialised purchasing team offers you a guaranteed top price On request, we deliver your new used vehicle nationwide directly to your door, and collect your trade-in for financing or leasing Immediate approval and settlement of existing credit Your specialist partner for cars, transporters, commercial vehicles, and construction machinery ITC GmbH & Co KG Siemensstraße 7 32312 Lübbecke (Industrial Area) Over 400 vehicles permanently in stock Hnodpfx Ajxt Sd Esi Aok The details provided in advertisements, on the internet, price tags, and images are non-binding descriptions and do not constitute guaranteed characteristics. The seller accepts no liability/warranty for typing or data transmission errors. Listed equipment may need to be checked separately. Our offer generally does not include new TÜV approval; we are happy to make you a quote with our partner workshop. Subject to errors and prior sale = Additional Information = Unladen weight: 2,360 kg Payload: 10,640 kg Gross vehicle weight: 13,000 kg

Stanje: rabljeno, največja dovoljena obremenitev: 15.100 kg, skupna masa: 20.000 kg, konfiguracija osi: 2 osi, prva registracija: 03/1987, dolžina tovornega prostora: 8.650 mm, širina tovornega prostora: 2.480 mm, ? Mehanske rampe ? Nakladalna višina: cca 910 mm ? Nosilec rezervnega kolesa ? Vlečno uho 40 mm ? Rotacijska luč ? Bobnasta zavora ? Listnato vzmetenje ? 1 x shranjevalna skrinja ? Dvojna kolesa ? SAF osi Vsi podatki brez garancije / Predhodna prodaja pridržana. Hjdpjyw Egwefx Ai Asnk

Stanje: rabljeno, največja dovoljena obremenitev: 29.850 kg, skupna masa: 32.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2012, naslednji pregled (TÜV): 04/2028, Leto izdelave: 2012, Interna številka vozila: G300402 Nemško vozilo Takoj na voljo na našem dvorišču v Kaufungen - Kassel, Nemčija Več INFO pri Luis Lucena Hnjdsxy Ul Sopfx Ai Ask Letnik 2012 Lastna masa priklopnika: 6.530 kg Priklopnik mešalec betona LIEBHERR 10 m³ Možne so napake. Z veseljem vzamemo vaše rabljeno vozilo v račun. Financiranje možno neposredno pri nas. GOLEC NUTZFAHRZEUGE GMBH Govorimo: nemško, angleško, špansko, poljsko, ukrajinsko, rusko, bolgarsko.

Stanje: rabljeno, številka stroja/vozila: GE11/142/2022, lastna masa: 6.350 kg, največja dovoljena obremenitev: 17.650 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, prva registracija: 08/2008, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.500 mm, vzmetenje: zrak, Zelo dobro ohranjeno vozilo iz prve roke Trosnažni nizkopodni priklopnik za prevoz Nizkopodni priklopnik z nakladalno rampo Prevoz težkih tovorov Tip T3 Komakt 30,0 Dolžina 8500 mm Širina 2500 mm Hedpfxjn Aw Hkj Ai Asnk Zračno vzmetenje Neto cena za trgovino/izvoz – 15.990 € Pridržujemo si pravico do sprememb, vmesne prodaje in napak ===== Telefon2 Mobilni telefon =====

Stanje: novo, največja dovoljena obremenitev: 16.500 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal ETÜ-TAR 21 Tandem – Low-Loader | Drive-over Platform Trailer Ref. for inquiries: 11630 Vehicle immediately available ex-stock Alsdorf NEW VEHICLE including COC (Certificate of Conformity) * Gross weight: 21 t, Payload: 16.5 t, galvanized chassis * Platform design with 400 mm high front wall, ramp safety by ramp holding frame and slanted bracing * Design: GW 21 t, reinforced frame and axle, axle spacing 1,810 mm * Deck height approx. 910 mm loaded / approx. 940 mm unloaded * 7 m loading area with 400 mm high front wall * Extended ramps: 3 m ramps, hot-dip galvanized, one-piece with galvanized grating * Ramp lifters with vertically mounted, adjustable springs for easy one-person operation * La-Si package: * 4 UVV safety lashing brackets (LC 8,000 daN), mounted to the existing hole pattern in the 45° outer frame, positioned about 1 m from the front and rear crossmembers * 10 retractable UVV lashing brackets (LC 3,000 daN) in the existing hole grid in the outer frame * 2 UVV lashing rings each at the front and rear, recessed in the crossmember (LC 10,000 daN) * Additional lashing points with 50 mm Ø drillings (LC 1,200 daN) in the front and rear crossmembers * Pre-fitted for retrofitting container locks (container locks available at extra charge) * Softwood floor, 50 mm thick * Air suspension, Gigant axles incl. EBS 2S/2M, raising and lowering * 235/75R 17.5 (8 units) twin tires with tire pressure monitoring sensors * Plastic toolbox in front of the front wall, right side in direction of travel * LED lighting system * 7-pin socket at the rear, prewired for oversize lighting with tail light (58R) and ground connection * 2 rear LED reverse lights * Side marker lights, flashing * Warning sign for oversize load * 1 removable LED rotating beacon incl. bracket and installation * Folding supports at the rear, support leg at the front with gear winch ---- Lease-purchase example from our partner MMV Leasing: €655/month net for 60 months, no down payment, and "0" Euro residual value Other terms with/without down payment/residual value available! We are official Müller-Mitteltal dealer ---- Our opening hours: * Monday – Thursday: 08:00 – 17:00 * Friday: 08:00 – 15:00 * Outside these hours, appointments possible by arrangement Hnsdpfx Aijyvxg Uj Aek * We speak German, English, Russian, Polish, and French * WhatsApp

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profile 30.0: * EBS braking system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical rear axle equalizer * Side underrun protection * Swivel supports at the rear on the chassis frame * Mechanically adjustable warning sign kits at the front and rear * Front: closed plastic mudguards, rear: straight galvanized steel mud flaps, each with splash guards * Contour marking tape, reflective, on sides and rear * Foldable (hot-dip galvanized) tool box cover on the turntable platform * Multi-voltage system * LED tail lights * Rotating beacon (removable) at the rear * Drawbar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin power connector * Four stake pockets each side (no stakes included), also suitable for lashing * Load securing package consisting of: 2 lashing points (6.4 t) at the front left & right on the main frame of the turntable platform, 5 pairs of UVV swivel and retractable lashing rings, loadable in all directions and recessed into the outer frame (13.4 t in corners, otherwise 10 t) * 6 pairs of mechanical folding outriggers for total width of 3 m (not in the rear slant) * Widening planks stored in the center of the loading area * Excavator arm support over rear axle up to the rear cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the sides in the excavator arm support) * Mechanical one-piece ramps with spring mechanism (approx. 3,000 x 720 mm) * Mechanically adjustable lateral ramp displacement * Loading area above the turntable: approx. 1,960 x 2,520 mm * Unladen loading height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height approx. 910 mm (including 860 mm approach incline) Hsdpfex Ipa Nox Ai Ajnk * Chassis, turntable, drawbar, and ramps hot-dip galvanized * Axles, springs, air tanks, etc. painted black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * -- Gross technical weight of 30,000 kg possible -- * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Subject to prior sale and errors * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profile 30.0: * EBS braking system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic leaf springs Hedpfx Aijx Ipavo Asnk * Mechanical rear axle compensation * Side underrun protection * Rear swivel supports on chassis frame * Mechanically adjustable warning panel sets front and rear * Front closed plastic fenders and rear straight galvanized steel skirts, each with splash protection * Contour tapes on sides and rear, reflective * Hinged lid (hot-dip galvanized) for tool box in the bogie platform * Multi-voltage system * LED tail lights * Removable beacon at the rear * Tow bar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin electrical connector * Four stake pockets each side (no stakes present) with simultaneous lashing options * Load securing package consisting of: 2 lashing eyes (6.4 t) at the front left & right on the main frame of the bogie platform, 5 pairs of UVV-compliant lashing rings - swiveling and retractable, loadable in all directions and integrated in the outer frame – 13.4 t at the corners, otherwise 10 t * 6 pairs of mechanical folding outriggers for 3 m overall width (not on rear taper) * Widening planks stored in the center of the loading platform * Excavator arm rest over rear axle up to the rear cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings fitted laterally in the arm rest) * Mechanically operated one-piece loading ramps with spring assembly (approx. 3,000 x 720 mm) * Mechanical lateral ramp adjustment * Loading area above turntable: approx. 1,960 x 2,520 mm * Unladen loading height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height approx. 910 mm (incl. 860 mm drive-on slope) * Chassis, bogie, tow bar, and loading ramps hot-dip galvanized * Axles, springs, air tank, etc., painted in black * 235/75 R17.5 twin tires * 5,900 kg curb weight * --Permissible total weight of 30,000 kg technically possible-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Errors and prior sale reserved * Immediately available ex Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 13.640 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2019, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.450 mm, višina nakladalnega prostora: 1.000 mm, skupna širina: 2.500 mm, HU: NOVO Skupna masa: 18.000 kg/20.000 kg Hnsdpfx Ajyw Ep Sei Aek Lastna masa: 4.360 kg Nosilnost: 13.640 kg/15.640 kg Dodatne informacije - dvojna kolesa 235/75R17,5 - osi Gigant - 4 pari pritrdilnih obročkov - pnevmatska zapora - znižljivo podvozje - nakladalne rampe pribl. 2.300 mm v prostor za shranjevanje - zadnja podporna noga - skladiščna omarica - zaščita proti podletu

Stanje: rabljeno, največja dovoljena obremenitev: 17.290 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/2017, naslednji pregled (TÜV): 07/2026, dolžina tovornega prostora: 8.900 mm, širina tovornega prostora: 2.520 mm, Oprema: ABS, * ABS * 5-komorni zadnje luči Hjdjyulu Ujpfx Ai Asnk * Oranžna rotacijska luč * Duomatik zračni priključek * BPW-ECO osi ----Nadgradnja: nizkopodni priklopnik, pocinkan okvir (1900+7000mm)/nakladalna višina pribl. 900 mm, zadaj poševno znižano/pristopna višina pribl. 770 mm, jeklena/lesena tla, razširljiv na 3 m, hidravlične nakladalne rampe (pocinkane) s protidrsno prevleko, prav tako hidravlično pomične v stran, vpenjalni obroči Prodaja samo pravnim osebam. PRI IZVOZU JE PLAČILO MOŽNO LE NETO ZNESEK!!!!! VSE INFORMACIJE BREZ GARANCIJE VKLJUČNO Z OPREMO IN DODATKI. Osnova vseh prodajnih pogodb, računov, predračunov, naročil in prodajnih pogovorov so naši splošni pogoji poslovanja (glejte impressum).

Stanje: novo, največja dovoljena obremenitev: 18.900 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA-Kombi 24.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Suspension: * Air suspension with manual lowering at rear ----Axles: * 3 x 11 t Gigant axles * Center axle liftable ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long with 40 mm towing eye & height adjustment device ----Electrics / Lighting: * LED rear lights * 15-pin electrical connector * TPMS (Tire Pressure Monitoring System) ----General Equipment: * Toolbox made of powder-coated steel sheet (W: 1,000 mm x H: 300 mm x D: 450 mm) * Storage box for container nets made of galvanized steel sheet (W: 960 mm x H: 300 mm x D: 450 mm) * Side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear impact protection buffers * Mechanical rear drop supports ----Container / Low-loader Platform: * Hot-dip galvanized main frame with raised outer rails (approx. 25 mm raised) for guiding roll-off containers * Steel floor with roller recesses in the bogie area * Suitable for roll-off container transport with lengths from 5,500 - 7,000 mm * Pneumatic 4-point container locking clamps and mechanically lockable end brackets at the front in the guide rails * Load securing certificate in accordance with DIN 30722-1 * Transport of up to 2 skip containers with a maximum of 10 m³ volume possible * Includes 8 repositionable skip locators for lateral centering of the skips, front 4 locators inserted with swiveling stops ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning devices for positive and non-positive securing of skips * 4 cloverleaf-style lashing rails (side) and 1 pair of 13.4 t UVV lashing rings at the front * Load securing certification according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 ----Ramps: * Welded beads as anti-slip coating on the slope in the running rail area * 1 pair of aluminum ramps (16 t/pair) 2,800 x 400 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from rear) ----Tyres: * Tyres: 235/75 R17.5 ----Ride Height: * Loaded ride height approx. 1,003 mm ----Payload: * Payload: 18,900 kg Hnjdjtplv Tepfx Ai Aek ----Painting: * Reflective contour tape on the sides & rear * Axles, turntable, drawbar, and air tank painted in a black tone * Main frame hot-dip galvanized ----Information: * Permissible gross weight of 27,000 kg technically possible * New vehicle without first registration with manufacturer's warranty * Errors and interim sales excepted ----Delivery Time: * Available from week 20/2026

Stanje: rabljeno, največja dovoljena obremenitev: 30.700 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2002, Oprema: ABS, * MüllerMitteltal nizkopodni priklopnik s 4 osmi T40 * 2x krmiljeni vrtljivi osi * Nemška prikolica * pero * hidravlično pomične rampe / levo-desno * deljene preklopne rampe * možnost razširitve * ABS * BPW osi * 40 t * lastna teža: 9300 kg * osne obremenitve = 10 t na os Hedpfx Aisyuri Eo Asnk * popolnoma funkcionalen * pnevmatike v redu

Stanje: novo, največja dovoljena obremenitev: 16.500 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal ETÜ-TAR 21 Tandem Low Loader / Flatbed Trailer, drive-over platform Reference No. for enquiries: 27963, available end of March 2026 NEW VEHICLE incl. COC * GVW: 21t, Payload: 16.5t, hot-dip galvanised chassis * Available end of March 2026 * Flatbed version with 400 mm high front wall, ramp safety provide by ramp holding rods and diagonal supports * Version: GVW 21 t, reinforced frame and axle, axle spacing 1,810 mm * Deck height approx. 910 mm loaded / approx. 940 mm unloaded * 7,000 mm loading platform with 400 mm high front wall * Extended ramps: 3,000 mm, one-piece hot-dip galvanised ramps with galvanised grating * Ramp lifters with vertically adjustable springs for easy single-person operation * Load securing package: * 4 UVV-compliant fall-type lashing rings (LC 8,000 daN) mounted to existing hole pattern in 45° outer frame, positioned approx. 1 m from front/rear cross-member * 10 UVV-compliant lashing rings (LC 3,000 daN) retractable in the existing hole grid of the outer frame * 2 UVV lashing rings each at front and rear, recessed in cross-members (LC 10,000 daN) * Additional lashing options via 50 mm (LC 1,200 daN) holes in front and rear cross-members * Fitting provisions for retrofitting container locks Hodpjyuq R Uofx Ai Ajnk * Softwood flooring, 50 mm thick * Air suspension with Gigant axles incl. EBS 2S/2M * Raise and lower function * 235/75 R17.5 (8x), twin tyres with tyre pressure monitoring sensor * 1 plastic toolbox in front of the bulkhead on the right-hand side (direction of travel) * LED lighting system * 7-pin socket on rear, wired for extra-length lighting with tail light (58 R) and ground * 2 LED reversing lights at rear * Flashing side marker lights * Oversize width warning panel * 1 removable LED beacon incl. holder and installation * Foldable rear supports, front support foot with gearbox winch ---- Finance lease sample from our cooperation partner MMV Leasing: €655/month net with 60 months term, no down payment and zero euro balloon payment Other terms possible with/without down payment / residual value. We are MüllerMitteltal authorised dealers. ---- Our opening hours: * Monday-Thursday: 08:00 - 17:00 * Friday: 08:00 - 15:00 * Outside of these hours by appointment We speak German, English, Russian, Polish, and French. Leasing, financing, trade-in possible.

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 11/2006, skupna dolžina: 7.900 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 385/65R22.5, barva: drugo, Leto izdelave: 2006, = Additional Options and Accessories = Body Hnjdpfx Aoycfuksi Ask - Year of manufacture: 2006 - Body capacity: 9 m³ (total body volume) - Material: Steel Engine - Number of fuel tanks: 1 = Further Information = General information Colour: Purple Suitable material: Concrete Axle configuration Tyre size: 385/65R22.5 Axle brand: BPW Eco Plus Brakes: Drum brakes Suspension: Air suspension Axle 1: Tyre tread left: 30%; Tyre tread right: 30% Axle 2: Tyre tread left: 10%; Tyre tread right: 20% Weights Unladen weight: 7,920 kg Payload: 21,080 kg Gross vehicle weight: 29,000 kg = Company Information = Would you like more information about this vehicle? We recommend visiting BAS World. There you will find: • HD inspection video • 360-degree images • Complete and verified specifications • Calculation of delivery costs and times • Support and services from BAS World Want to know more? Visit BAS World online! España (ES): We speak 17 languages so we can always assist you in your own language. Please feel free to contact us directly. Our Spanish-speaking employee will be happy to help you! Deutschland (DE): We speak 17 languages so we can always help you in your own language. Feel free to contact us directly. Our German-speaking employee will be happy to assist you! France (FR): We speak 17 languages so we can always help you in your own language. Do not hesitate to contact us directly. Our French-speaking employee will be happy to help you! Portugal (PT): We speak 17 languages so we can always assist you in your own language. Feel free to contact us directly. Our Portuguese-speaking employee will be delighted to help you! Italia (IT): We speak 17 languages so we can always assist you in your own language. Do not hesitate to contact us directly. Our Italian-speaking employee will be glad to help you!

Stanje: rabljeno, največja dovoljena obremenitev: 9.400 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 07/2020, dolžina tovornega prostora: 6.300 mm, širina tovornega prostora: 2.480 mm, Int.-št.: ZANDT Zelo dobro vzdrževana tandem šasija s kesonom ZANDT Cargo * TAT B 110 Hnjdpfsymuz Uox Ai Ask * Keson * Ojačano leseno dno * Težko nosilne pritrdilne tirnice * Dvoosna tandem os * Široke pnevmatike * Nastavljiva vlečna kljuka * Največja dovoljena masa 11.900 kg * Zelo dobro stanje Možna je menjava staro za novo Financiranje od 3,99% Pridržujemo si pravico do napak in vmesne prodaje! Podatki v tem oglasu so neobvezujoči opisi in ne predstavljajo zagotovljenih lastnosti. Prodajalec ne prevzema nobene odgovornosti za tipkarske ali prenosne napake. Oprema iz oglasa se preveri posebej. Vsi podatki v oglasih so neobvezujoči! Dostava po celotni Nemčiji na zahtevo Delovni čas: ponedeljek do četrtek od 9:00-17:00, petek od 9:00-14:00 ali po dogovoru!

Stanje: rabljeno, največja dovoljena obremenitev: 9.400 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 07/2020, dolžina tovornega prostora: 6.300 mm, širina tovornega prostora: 2.480 mm, Int. št.: ZANDT zelo dobro vzdrževana tandem ploščadna prikolica ZANDT Cargo * TAT B 110 Hedpfx Asymuz Iei Ajnk * ploščad * ojačan lesen pod * pritrdilne tirnice za težke tovore * tandem z dvema osema * široke pnevmatike * nastavljivo vlečno oje * dovoljena skupna masa 11.900 kg * zelo dobro stanje Možnost menjave starega za novo Financiranje od 3,99 % Napake in vmesna prodaja pridržane! Podatki v tem oglasu so nezavezujoči opisi in ne veljajo kot zagotovljene lastnosti. Prodajalec ne prevzema odgovornosti za tipkarske napake ali napake pri prenosu podatkov. Oprema, navedena v oglasu, je treba posebej preveriti. Vsi podatki v oglasih so nezavezujoči! Dostava po celotni Nemčiji na zahtevo Delovni čas: ponedeljek do četrtek od 9:00 do 17:00 petek od 9:00 do 14:00 in po dogovoru!!!

Stanje: novo, največja dovoljena obremenitev: 23.940 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2025, * T3 Profi 30.0: * EBS braking system * RDÜ tire pressure monitoring Hsdpol Th I Aofx Ai Aonk * Emergency release mechanism for spring brake cylinders * Drum brakes * 3 x 11t Gigant axles * Parabolic springs, mechanical axle compensation at the rear * Side underrun protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning board sets at front and rear * Front: closed plastic mudguards; Rear: straight, galvanized sheet steel skirts, each with spray protection * Reflective contour tape on the sides and rear * Tool box made of galvanized sheet steel, powder-coated black, approx. 650 x 300 x 600 mm * Hinged lid (hot-dip galvanized) for tool box within the turntable platform * Multi-voltage wiring * LED tail lights * Rear warning beacon (detachable) * Drawbar with 50 mm draw eye and height adjustment via tension spring & turnbuckle * 15-pin electrical socket * Four stake pockets per side (stakes not included), also usable as lash points * Load securing package comprising: 2 lashing eyes (6.4 t) at the front left & right on the main frame of the turntable platform, 6 pairs of UVV-certified lashing rings, swiveling and retractable, loadable in all directions, recessed into the outer frame; corner rings: 13.4 t, other rings: 10 t * 6 pairs of mechanical folding extensions for 3 m total width (not at the rear slope) * Widening boards stored at the center of the load floor * One-piece, hot-dip galvanized hydraulic access ramps (approx. 3,000 x 720 mm), manually adjustable sideways * 4-way valve block for hydraulic side ramp retrofit * Platform above turntable: approx. 1,960 x 2,520 mm * Unladen platform height: approx. 1,070 mm * Rear platform: approx. 6,500 x 2,520 mm * Unladen platform height: approx. 910 mm (incl. 860 mm drive-on angle) * Chassis, turntable, drawbar, and access ramps hot-dip galvanized * Axles, springs, air tanks, and related components painted in black * 235/75 R 17.5 twin tires * Approx. 5,980 kg unladen weight * Permissible total technical weight: 30,000 kg * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from week 11/2026

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring-loaded cylinders Hnodpfjl Tik Njx Ai Aok * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting/lowering system and RtR valve * Smard board for payload weighing * Warning sign kits, front and rear * Reflective contour tape on the sides and rear * Removable rotating beacon (rear) * LED lighting * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated steel sheet and basket-type spare wheel holder, mounted right side * Front: closed single plastic mudguard * Rear: straight steel mudguards, each with spray suppression * Side underrun protection * Bogie platform extension by 520 mm with 45° corners, 3 integrated lockable storage compartments with lids * Chassis made of high-strength fine-grained steel * 50 mm softwood floor over bogie platform, 60 mm softwood on low-bed platform * Outer rails on ramps made of hardwood * 4 stake pockets per side (no stakes included); 2 t lashing possible at each * Load securing package: 2 lashing eyes (6.4 t) front left/right on main frame of bogie platform * 2 pairs of lashing rings (13.4 t) on outer frame front/rear per side; 4 pairs of lashing rings (10 t), swing-out and lowerable per side (front/rear) * All lashing points loadable in all directions and recessed into outer frame * 2 pairs of lashing rings (6.4 t) in excavator arm rest area * 8 pairs of galvanized folding outriggers for 3 m overall width (not at rear slope) * Extension planks stored left side in a storage box * Excavator arm rest above rear axle to end of rear slope, approx. 2,100 x 740 x 190 mm * Rear mechanical fall supports * Hydraulic folding ramps with hydraulically adjustable ramp tip, approx. 4,650 x 720 mm, incl. hydraulic lateral ramp adjustment & load-holding valve * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Loading height loaded approx. 890 mm, +/-20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, bogie, ramps, outriggers and mechanical fall supports hot-dip galvanized * Axles, drawbar, air reservoir and turntable in black finish * Tires: 235/75 R 17.5 * New vehicle, no initial registration, manufacturer’s warranty * Subject to errors and prior sale * Immediately available ex Egestorf, A7

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lift/lowering system and RtR valve * Smard board for load weight determination * Warning sign packages front & rear * Reflective contour marking tapes on sides and rear Hnsdpfx Aijl Tphrj Ask * Rotating beacon (removable) at rear * LED lights * Straight drawbar with 50 mm towing eye and continuously adjustable height * Tool box made of powder-coated sheet steel and spare wheel holder in basket design, right-hand side * Closed single plastic mudguards at front * Straight rear steel splash guards, each with spray suppression * Side underrun protection * Turntable platform front extension by 520 mm with 45° corners and 3 flush storage compartments with lids, lockable * Chassis made of high-strength fine-grained steel * Decking above turntable platform: 50 mm softwood, in low-bed platform: 60 mm softwood * Outer planks of access ramps: hardwood * Each side features 4 stake pockets (stakes not included), with simultaneous 2 t lashing points * Lashing package includes: 2 lashing rings 6.4 t, front left and right on main frame of turntable platform * On sides, front & rear, 2 pairs of 13.4 t lashing rings on outer frame; sides each with 4 pairs of 10 t lashing rings, pivoting & lowerable * Loadable in all directions, recessed in the outer frame * 2 pairs of 6.4 t lashing rings on the excavator stick rest area * 8 pairs of galvanized folding outriggers for 3 m overall width (not in the rear slope) * Extension planks stored left side in a stowage compartment * Excavator stick rest above rear axle to rear slope approx. 2,100 x 740 x 190 mm * Mechanical drop supports, rear * Hydraulic folding ramps with hydraulic tip section approx. 4,650 x 720 mm including lateral hydraulic ramp shift & load holding valve * Load area over turntable: approx. 2,990 x 2,520 mm * Rear load area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm drive-on slope) * Flow divider installed * Chassis, turntable, ramps, outrigger arms, and mechanical rear supports hot-dip galvanized * Axles, drawbar, air reservoir, and turntable painted in a black tone * Tires: 235/75 R 17.5 * New vehicle, not previously registered, with manufacturer warranty * Subject to errors and prior sale * Immediately available ex Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 23.940 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profi 30.0: * EBS braking system * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t Gigant axles Hedpfx Ajl Th Nnei Ajnk * Parabolic springs, mechanical rear axle equalization * Side underrun protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at front and rear * Front axle: closed plastic mudguards; rear axle: straight, galvanized steel skirts, each with spray protection * Reflective contour marking tape on the sides and rear * Tool box made of galvanized sheet steel – black powder-coated – approx. 650 x 300 x 600 mm * Folding lid (hot-dip galvanized) for the toolbox on the turntable platform * Multi-voltage system * LED tail lights * Rotating beacon (removable) at the rear * Drawbar with 50 mm towing eye and height adjustment via drawbar spring & turnbuckle * 15-pin electrical plug * Four stake pockets on each side (no stakes included), with integrated lashing option * Load securing package consisting of: 2 lashing rings (6.4 t) at the front left & right on the main frame of the turntable platform, 6 pairs of UVV-compliant lashing rings, swiveling and retractable, loadable in all directions and recessed in the outer frame – 13.4 t in the corners, otherwise 10 t. * 6 pairs of mechanical folding outriggers for 3 m overall width (not on the rear slope) * Widening boards stored in the center of the loading area * Hot-dip galvanized one-piece hydraulic ramp (approx. 3,000 x 720 mm), mechanically adjustable sideways * 4-section control valve block for retrofitting hydraulic side ramp shifting * Loading area above turntable: approx. 1,960 x 2,520 mm * Loading height unladen: approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Loading height unladen: approx. 910 mm (including 860 mm approach slope) * Chassis, turntable, drawbar, and ramps hot-dip galvanized * Axles, springs, air tanks etc. painted black * 235/75 R 17.5 twin tires * Approx. 5,980 kg unladen weight * Technical gross vehicle weight of up to 30,000 kg possible * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from week 11/2026

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profile 30.0: * EBS braking system Hodox Ipbgopfx Ai Ajnk * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical rear axle equalization * Side underrun protection * Swing-down supports at the rear of the chassis frame * Mechanically adjustable warning board sets front and rear * Front axle with closed plastic mudguards, rear axle with straight galvanized steel skirts, each with spray protection * Reflective contour tape on the sides and rear * Hinged (hot-dip galvanized) tool box lid on the turntable platform * Multi-voltage system * LED rear lights * Rotating beacon (removable) at the rear * Drawbar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin electrical socket * Four stake pockets on each side (however, no stakes included), with simultaneous lashing capability * Load securing package consisting of: 2 lashing eyes (6.4 t) front left & right on the main frame of the turntable platform, 5 pairs of UVV lashing rings, swiveling and lowerable, loadable from all directions and recessed in the outer frame – in the corners 13.4 t, otherwise 10 t * 6 pairs of mechanical folding outriggers for 3 m total width (but not in the rear slope) * Widening planks stored in the center of the loading area * Excavator arm resting cradle over the rear axle up to the end cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the side in the excavator arm cradle) * Hydraulically operated one-piece loading ramps (approx. 3,000 x 720 mm) * Hydraulically lateral ramp displacement * Loading area above turntable: approx. 1,960 x 2,520 mm * Unladen loading height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height approx. 910 mm (incl. 860 mm approach slope) * Chassis, turntable, drawbar, and loading ramps hot-dip galvanized * Axles, springs, air tanks, etc. painted in black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * --Permissible total weight of 30,000 kg technically possible-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf on the A7