Müller-Mitteltal Nizki Nakladalnik nakup rabljenega (252)

Stanje: novo, največja dovoljena obremenitev: 31.630 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.250 mm, širina tovornega prostora: 2.520 mm, * T 4: * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Parabolic springs * Mechanical axle compensation, front and rear * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) * Warning sign packages front & rear * Reflective contour tape on sides and rear * EBS multi-voltage system for 12 & 24 V electrics * Removable LED beacon, rear * 24 V – 15-pin and additional 12 V – 7+4 pin power cable * Extended connection cables for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm towing eye and stepless height adjustment * Toolbox made of powder-coated sheet steel and spare wheel holder in basket design, mounted right side * Closed single plastic mudguards front * Rear straight steel mud flaps each with spray suppression * Lateral underrun protection * Extended offset crank by 500 mm to the front Nsdpfxsl Th Evs Af Aswc * Turntable platform front section extended by 520 mm with 45° corners and 3 integrated, lockable storage compartments with lids * Chassis made from high-strength fine-grained steel * Flooring over turntable platform made of 50 mm softwood, and in lowbed platform from 60 mm softwood * Outer boards of access ramps made of 50 mm bamboo * Four stake pockets per side (stakes not included), each with 2 t lashing point capacity * Lashing package consisting of: 2 lashing eyes 6.4 t on main frame of turntable platform (front left and right); 1 pair of 13.4 t lashing rings per side front and rear on outer frame; 4 pairs per side of 10 t pivoting and lowerable lashing rings, loadable in all directions, recessed in outer frame; 2 pairs of 6.4 t lashing rings on each side in the excavator arm recess; 8 pairs galvanized folding markers for 3 m overall width (not on rear slope) * Extension planks stored in left-side compartment * Excavator arm recess above rear axle to end of approach slope approx. 2,300 x 740 x 190 mm * Mechanical drop-down supports rear * Hydraulic, hot-dip galvanized access ramps approx. 3,000 x 720 mm * Hydraulic lateral ramp adjustment via sliding tube from ramp shaft * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Loaded loading height approx. 860 mm (includes 860 mm approach slope) * Chassis, turntable, loading ramps, mechanical folding supports rear hot-dip galvanized * Axles, springs, air tanks and turntable painted black * New vehicle with manufacturer warranty * Subject to errors and prior sale * Available from week 21/2026

Stanje: rabljeno, največja dovoljena obremenitev: 8.000 kg, skupna masa: 11.000 kg, konfiguracija osi: 2 osi, prva registracija: 10/2000, dolžina tovornega prostora: 5.600 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, Gross weight: 11,000 kg Unladen weight: 3,000 kg Payload: 8,000 kg Overall length: 7,450 mm Loading length: total 5,600 mm, including rear sloping section 1,000 mm Width: overall width 2,550 mm / platform width 2,480 mm Loading height: approx. 900 mm Further information - Sideboard height: 400 mm, split, foldable - Split spring-assisted ramps, dimensions approx. L: 3,380 mm W: 600 mm - Ramps covered with phenolic resin-coated plywood - Large lashing package - BPW axles - Tyres 235/75 R17.5 Nedpfxswz Drgo Af Aswc - LED reversing lights - Plastic toolbox

Stanje: novo, največja dovoljena obremenitev: 10.750 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-R 14.4: ----Brakes: * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with balancing unit ----Drawbar / Flange Towing Eye: * Drawbar height adjustable by 300 mm * Drawbar extension by 250 mm to a total of 2,250 mm * 40 mm flange towing eye ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin power connector * LED lighting ----General Attachments: * Support winch at the front Nwedev Eq Evjpfx Af Aoc * Rear fold-out support legs (external) * Plastic toolbox approx. 858 x 500 x 500 mm, mounted front right, outside on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low-loader Platform: * 50 mm softwood flooring * Preparation in front of the bulkhead and rear slope for retrofitting container locks for transporting 20" containers * Bolt-on bulkhead made of smooth sheet metal * Trapezoidal-profiled steel side panels, mid-hinged, split once * Rear panel, insertable between the ramp holders, can be stored in front of the bulkhead when not in use * Bolt-on rear stanchions ----Load Securing: * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Option to install 3 t recessed lashing rings every 600 mm * 1 x 6.3 t lashing point in each of the front and rear corners * Various holes in the bulkhead and end crossmember for 1.2 t lashing possibilities ----Ramps: * One-piece mechanical grating ramps with spring mechanism for one-person operation, approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Approx. 860 mm chassis approach angle at rear ----Wheelbase: * Wheelbase 1,140 mm ----Paintwork: * Drawbar, bulkhead, tailboard, fold-out support legs, and ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and support winch painted in a black hue * Sideboard panels painted RAL 9010 pure white * Painting of side panels in any RAL color available at extra cost ----Information: * Reinforced and certified body to EN 12642 XL incl. load securing certificate * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery Time: * Available immediately from Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic suspension with tandem balancing unit ----Drawbar / Flange Eye: * Height-adjustable drawbar (300 mm) with 40 mm flange towing eye ----Electrics / Lighting: * Tyre pressure monitoring with in-cab display via EBS signal (no additional truck-side installation required) * 15-pin power connector * LED tail lights ----General Attachments: * Mechanical support winch at the front * Two mechanical folding supports at the rear * Plastic tool box approx. 750 x 350 x 300 mm, right-hand side * Bolt-on underride guard * Plastic quarter mudguards ----Chassis: * Main frame made of high-tensile fine-grained steel Njdpfx Ajtr Sucjf Aewc ----Tipper Body: * Mesh hooks on the sides and rear in the central locking mounts, plus 2 hooks on the front wall * Steel pallet 2-way tipper body, fixed headboard made of smooth sheet metal, continuous side walls – drop-down without central stanchions, sideboard spring assists and swinging function via manual central locking * Rear stanchions bolted * Steel rear wall inserted in front of ramps * 1 x 5 t lashing point in each corner, plus 4 x 3 t lashing rings on each side, recessed into outer frame * 4 mm floor made of high-tensile fine-grained steel ----Ramps: * Two-piece mechanical grid ramps with aluminium tip: 2,150 + 1,300 mm x 600 mm (manually retractable to 80 mm) ----Paintwork: * Chassis, drawbar, rear stanchions, underride guard, mechanical props, and loading ramps hot-dip galvanised * Axles, springs, air tanks, flange towing eye, and support winch painted in black * Sideboards and body finished in RAL 9010 pure white * Optional body and side wall painting in other RAL shades at extra cost ----Information: * Brand new vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Available from CW 07/2026

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer assembly ----Drawbar / Flange-Type Towing Eye: * Height-adjustable drawbar by 300 mm with 40 mm flange towing eye ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal, no truck-side installation required * 15-pin power connector * LED tail lights ----General Attachments: * Mechanical landing gear at the front * Two mechanical folding support legs at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * Bolted underrun protection * Plastic quarter mudguards ----Chassis: * Main frame made of fine-grain steel ----Tipper Platform: * Mesh hooks on sides and rear located at the central locking mounts, plus 2 on the front wall * Steel pallet two-way tipping body, front wall fixed, made of smooth plate; continuous collapsible sidewalls (without center posts), with drop side spring lifters and manual central locking for tilting * Rear stanchions bolted * Steel rear wall slid in front of the ramps * Each corner with 1 x 5 t lashing point; 4 x 3 t lashing rings recessed into the outer frame on each side * 4 mm floor made of fine-grain steel ----Ramps: * Two-piece mechanical grating drive-up ramps with aluminium tip section 2,150 + 1,300 mm x 600 mm (can be slid together manually up to 80 mm) ----Paintwork: * Chassis, drawbar, rear stanchions, underrun protection, mechanical stabilizer legs, and ramps hot-dip galvanized * Axles, springs, air tanks, towing eye, and landing gear painted in black * Sidewalls and platform in RAL 9010 pure white * Paint finish of sidewalls and tipper platform available in RAL color of choice at extra charge ----Information: * New vehicle with manufacturer warranty * Subject to prior sale and errors ----Delivery time: Nwsdpjtr St Ujfx Af Aec * Available from calendar week 07/2026

Stanje: novo, največja dovoljena obremenitev: 10.750 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-R 14.4: ----Braking System: * EBS brake system * Emergency release device for spring brake cylinders * Drum brakes ----Axle: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with equalizing unit ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm to a total length of 2,250 mm * 40 mm flange towing eye ----Electrics / Lighting: * TPMS (tire pressure monitoring system) * 15-pin power connector * LED lighting ----General Fittings: * Support winch at the front * External folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, front right outside on the front wall * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood flooring * Preparation in front of the bulkhead and rear slope for subsequent installation of container locks for transporting 20" containers * Bolted smooth sheet metal bulkhead * Side panels made of trapezoidal profiled steel sheet, foldable, split once in the middle * Steel rear wall, can be inserted between the ramp holders when not in use, stored inside at the front wall * Bolted rear stakes ----Load Securing: * Perforated outer frame, bent approx. 45 degrees, with 2t lashing capacity every 480 mm * Option to fit 3t recessed lashing rings every 600 mm * 1 x 6.3t lashing ring in each front and rear corner * Various holes in the front and rear cross members for 1.2t lashing options ----Ramps: * One-piece mechanical grating access ramps with spring mechanism for one-man operation, approx. 2,750 x 600 mm (collapsible to 20 mm) * Rear approach slope approx. 860 mm on chassis ----Wheelbase: * Wheelbase 1,140 mm ----Painting: * Drawbar, bulkhead, tailgate, folding supports and access ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye and support winch painted in a shade of black Nwodpfx Afsv D Tcbo Aoc * Side panels painted in RAL 9010 pure white * Side panel painting in other RAL colors available at extra cost ----Information: * Reinforced and certified construction in accordance with EN 12642 XL incl. load securing certificate * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available from Egestorf on the A7

Stanje: rabljeno, največja dovoljena obremenitev: 31.600 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 12/2001, Oprema: ABS, Vehicle identification number: WMM0000010046004 Unladen weight: 8,400 kg German roadworthiness inspection (HU): due BPW Eco axles with drum brakes Leaf spring suspension Upper deck length: 2,500 mm – loading height: 1,070 mm Lower deck length: 7,200 mm – loading height: 885 mm Drawbar – 50 mm Hydraulic ramps, split – length 2,000 + 1,300 mm – width 660 mm Support legs Tyres: 235/75 R 17.5 Modifications, prior sale, and errors excepted. The description serves for general vehicle identification and does not constitute a warranty in the legal sense. The contractual description as per the purchase agreement is legally binding. Our offers generally do not include a new technical inspection (TÜV certificate). If a new TÜV certificate is required, we will be pleased to provide an offer from our partner workshops. Vehicle may feature advertising stickers and/or lettering. Our general terms and conditions of delivery and payment apply. Nwodpfx Afjwwd R Is Aoc

Stanje: novo, največja dovoljena obremenitev: 8.620 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2024, * KA-TA-R 11.9: ----Braking system: * Electronic braking system (EBS) Nodjm Angvopfx Af Aewc * Emergency release device for spring-type actuators * Drum brakes ----Axles: * 2 x 5.5 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer unit ----Drawbar / Flange Eye: * Hot-dip galvanized drawbar with 40 mm flange eye, height-adjustable by 300 mm ----Electrics / Lighting: * Tire Pressure Monitoring System (TPMS) * 15-pin power connector * LED tail lights ----General Attachments: * Jost mechanical landing leg at the front * 2 mechanical hot-dip galvanized fold-down supports at the rear * Galvanized steel toolbox, right side * Hot-dip galvanized bolted underrun protection * Plastic quarter mudguards ----Tipping body: * Mesh hooks at sides and rear in the central locking mounts and 3 pieces on the front wall * Hot-dip galvanized chassis * Steel platform – 3-way tipper body * Continuous side walls without center stanchions, foldable with drop-side spring lifter * Rear tailgate foldable and swinging via manual central locking * Bolt-on hot-dip galvanized rear stanchions * 4 mm steel floor plate * Prepared for later installation of drop-side extensions * 5.5-meter-long body ----Load securing: * 1 x 5 t lash ring in each corner * 4 x 3 t lashing eyes each side, recessed in the outer frame ----Ramps: * Rear guide rail for loading ramps * 1 pair of aluminum loading ramps, approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment under the loading platform, integrated into the chassis, accessible from the rear ----Wheelbase: * Wheelbase: 990 mm ----Tyres: * Tyres: 235/75R17.5 ----Paintwork: * Axles, springs, air tanks, drawbar, and landing leg painted black * Body color: RAL 9010 pure white * Painting of side walls and tipping body in any RAL color available at extra cost ----Information: * Reinforced body with load securing certificate according to EN 12642 XL * New vehicle without initial registration, with manufacturer's warranty * Subject to errors and prior sale ----Delivery time: * Available immediately from Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 8.620 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2024, * KA-TA-R 11.9: ----Brakes: * Electronic braking system (EBS) * Emergency release system for spring brake cylinders * Drum brakes ----Axle: * 2 x 5.5 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer assembly ----Drawbar / Flange Eye: * Hot-dip galvanized, height-adjustable drawbar (adjustable by 300 mm) with 40 mm flange eye ----Electrics / Lighting: * Tire pressure monitoring system (TPMS) * 15-pin power connector * LED rear lights ----General Attachments: * JOST mechanical landing gear at the front * 2 mechanical, hot-dip galvanized drop legs at the rear * Toolbox made from galvanized sheet steel on the right side * Hot-dip galvanized bolted underrun protection Nsdpjl Thx Ejfx Af Aswc * Plastic quarter mudguards ----Tipping Platform: * Net hooks on the sides and rear at the central locking mounts, plus 3 hooks on the front wall * Hot-dip galvanized chassis * Steel pallet – 3-way tipper body * Fold-down continuous side walls without center posts, with drop side spring-assist * Rear wall can fold down or swing via manual central locking * Hot-dip galvanized, bolted rear stanchions * 4 mm steel floor plate * Preparation for retrofitting additional side wall extensions * Bridge length: 5.5 meters ----Load Securing: * 1 x 5 t lashing ring in each corner * 4 x 3 t lashing points recessed in the outer frame on each side ----Ramps: * Rear mounting track for loading ramps * 1 pair of aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment for ramps recessed under cargo area at the rear of the chassis ----Wheelbase: * Wheelbase: 990 mm ----Tyres: * Tyres: 235/75R17.5 ----Painting: * Axles, springs, air tanks, drawbar, and landing gear painted in black * Tipping body color: RAL 9010 pure white * Painting of side walls and tipping platform in any RAL color available for an additional charge ----Information: * Reinforced body with load securing certificate according to EN 12642 XL * New vehicle, no initial registration, with manufacturer’s warranty * Subject to prior sale and errors excepted ----Delivery time: * Available immediately ex Egestorf, A7

Stanje: rabljeno, lastna masa: 3.100 kg, največja dovoljena obremenitev: 7.400 kg, skupna masa: 10.500 kg, konfiguracija osi: 2 osi, prva registracija: 03/2006, naslednji pregled (TÜV): 03/2026, dolžina tovornega prostora: 6.000 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 360 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75R17.5, barva: bež, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Lokacija vozila: Bovenden, 2 osi, BPW osi, tandem, listnato vzmetenje, ABS (protiblokirni sistem), pritrdilna ušesa, mehanske rampe, podpora spredaj, podpora zadaj, shranjevalni zaboj, vlečna droga nastavljiva po višini. Nadgradnja: tandem nizkopodni priklopnik z mehanskimi naletnimi rampami, 2x BPW osi, bobnaste zavore, vrtljivo vlečno uho 40 mm in 50 mm, vlečna droga nastavljiva po višini! Nakladalna višina ca. 900 mm! Dolžina ramp ca. 2700 mm! Podatki o dodatni opremi brez garancije, spremembe, vmesna prodaja in napake pridržane! Njdpfx Asx Rdqhsf Aewc

Stanje: rabljeno, lastna masa: 3.280 kg, največja dovoljena obremenitev: 14.600 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 09/2013, vzmetenje: zrak, velikost pnevmatike: 265/70 R19,5, medosna razdalja: 5.030 mm, Oprema: ABS, Müller-Mitteltal hooklift trailer | Toolbox | Hot-dip galvanized | Tyres: 265/70R19.5 | BPW disc brakes | TÜV valid until | Subject to errors, input mistakes, and prior sale. Nwsdpfx Aewd Sdcjf Aoc

Stanje: novo, največja dovoljena obremenitev: 14.400 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-ER 19.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release mechanism for spring-loaded cylinders * Drum brakes * 2 x 11 t Gigant axles * Air suspension with lifting and lowering system * Drawbar with 50 mm flanged towing eye and height adjustment of 110 mm via offset plate * Jost support winch at the front * External folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * Side underrun protection * Plastic quarter mudguards * 15-pin electrical connector * Multi-chamber tail lights * Reinforcement package for drilling rig transport on the chassis * 50 mm softwood flooring, clamped version * Preparation in front of the bulkhead for subsequent installation of container locks * Bolted front bulkhead made of smooth sheet metal * Split side walls made of trapezoidal-profile steel sheet, foldable, with folding stanchion in the middle * Steel rear wall, insertable between the ramps; stowage fixture in front of the bulkhead when not in use * Bolted rear stakes * Perforated outer frame approx. 45 degrees angled, with 2 t lashing capacity every 480 mm * Option to fit 3 t drop lashing rings every 600 mm * Load securing package: in each front and rear corner 1 x 10 t UVV lashing ring, 2 x 8 t retractable UVV lashing rings per side in the outer frame, various holes in the front and rear crossmember for 1.2 t lashing options * One-piece slide-in ramps, 12 t per pair, approx. 2,750 x 620 mm * Rear approach angle approx. 860 mm * Chassis, drawbar, front wall, tailgate, folding supports and loading ramps hot-dip galvanized * ---Axles, air tanks, flanged towing eye, and support winch painted in black--- * Loading height unladen approx. 940 mm * Loading height laden approx. 910 mm * Wheelbase: 1,810 mm * Tyres: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale excepted Nwsdomi Tmaepfx Af Ajc * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 14.400 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-ER 19.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 11 t Gigant axles * Air suspension with lifting and lowering system Nwedpfx Afemi Tcqo Ajc * Drawbar with 50 mm flange towing eye and height adjustment of 110 mm via offset plate * Jost landing gear at the front * External folding support legs at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * Side underrun protection * Plastic quarter mudguards * 15-pin electrical connector * Multi-chamber rear lights * Reinforcement package for drilling rig transport on chassis * 50 mm softwood floor, clamped version * Fixture in front of the bulkhead for subsequent installation of container locks * Bolted bulkhead made from smooth steel sheet * Split steel sidewalls - trapezoidal profile - foldable with central folding stake * Steel rear wall, slidable between ramps - interior mounting bracket for storage when not in use, in front of the bulkhead * Bolted rear stanchions * Perforated outer frame, approx. 45° bent, with 2 t lashing capacity every 480 mm * Possible to install 3 t folding lashing brackets every 600 mm * Load securing package: at each front and rear corner 1 x 10 t UVV-rated lashing ring, on each side 2 x 8 t UVV-rated retractable lashing rings in outer frame, various holes in front and rear crossmembers for 1.2 t lashing options * One-piece sliding ramps 12 t/pair, approx. 2,750 x 620 mm * Rear drive-on bevel approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, folding supports, and drive-on ramps hot-dip galvanized * ---Axles, air reservoirs, flange towing eye, and landing gear painted black--- * Unladen loading height approx. 940 mm * Laden loading height approx. 910 mm * Wheelbase: 1,810 mm * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Stanje: rabljeno, številka stroja/vozila: 217, lastna masa: 3.450 kg, največja dovoljena obremenitev: 14.550 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 01/1993, vzmetenje: jeklo, velikost pnevmatike: 385/65 r22,5, medosna razdalja: 5.300 mm, barva: oranžna, Oprema: ABS, Drum brake Subject to errors and omissions Nedpfjnh Rzyjx Af Aswc

Stanje: novo, največja dovoljena obremenitev: 8.800 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.370 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-R 11.9: ----Brakes: * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes, 2 x 5.5 t ----Axles: Nwjdpfsl Th Nrsx Af Aec * Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange Towing Eye: * Drawbar height adjustable by 300 mm * 40 mm flange towing eye ----General Attachments: * Jost landing gear front * Rear external folding supports * Plastic toolbox front right, outside on the front wall * Side underrun protection * Plastic quarter mudguards ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * LED lighting ----Loading Platform: * Loading platform 5.37 m * 50 mm softwood flooring * Bolted front wall made of smooth sheet steel * Side walls made of trapezoidal-profile steel sheet, foldable with drop-side spring assist * Rear wall made of steel, can be slid in between ramp mounts, stored inside in front of the front wall when not in use * Rear stanchions bolted ----Load Securing: * Perforated outer frame, approx. 45° bent, with 2 t lashing capacity every 480 mm * Option to install 3 t recessed lashing rings every 600 mm * 1 x 6.3 t lashing ring in each front and rear corner * Various holes in the front and rear cross-members for 1.2 t lashing options ----Ramps: * One-piece mechanical mesh loading ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be compacted to 20 mm) * Rear approach incline approx. 860 mm chassis ----Tyres: * Tyres 235/75 R 17.5 ----Wheelbase: * Wheelbase: 990 mm ----Paintwork: * Drawbar, front wall, tailgate, folding supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, and 40 mm flange towing eye painted in black * Drop-sides painted in RAL2011 deep orange * Painting of the side walls in any RAL colour available at extra cost ----Info: * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 8.870 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-ER 11.9: ----Braking System: * Electronic braking system (EBS) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: Nodpfx Afel Thy Ro Ajwc * 2 x 5.5 t Gigant axle assemblies ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange Drawbar Eye: * Height-adjustable drawbar, approx. 300 mm * 40 mm flange drawbar eye ----General Attachments: * Jost mechanical landing gear, front * External, hot-dip galvanized folding supports, rear * Side underrun protection * Plastic quarter mudguards * Plastic toolbox, front right, mounted on front wall outside ----Electrics / Lighting: * Tire pressure monitoring system (TPMS) * 15-pin power connector * LED tail lights ----Loading Platform: * 50 mm softwood floor * 20'' container locks mounted at front and rear * Bolted smooth steel front wall * Drop sides, steel, trapezoidal profile, drop-down with drop-side lifting springs * Hot-dip galvanized, bolted rear stanchions ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing brackets every 600 mm (5 lashing rings fitted each side) * 1 x 6.3 t lashing ring fitted in each corner front and rear * Various holes in front and rear transverse beams for 1.2 t lashing options ----Ramps: * 1 pair of aluminium loading ramps, approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tyred and tracked vehicles * Rear storage compartment integrated in the chassis below the loading area ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, front wall, and rear wall * Drop side color in RAL 9010 pure white * Side panels can be painted in a RAL color at extra cost ----Info: * New vehicle without registration * Subject to prior sale and errors excepted ----Delivery Time: * Available immediately from Egestorf

Stanje: novo, največja dovoljena obremenitev: 8.800 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.370 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-R 11.9: ----Brakes: * EBS brake system * Emergency release device for spring brake cylinders * Drum brakes, 2 x 5.5 t ----Axles: * Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar by 300 mm * 40 mm flange towing eye ----General Attachments: * Jost landing gear at the front * External folding supports at the rear * Plastic toolbox, front right outside on the front wall * Side underrun protection * Plastic quarter mudguards ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * LED lighting ----Loading Platform: * Platform length 5.37 m * 50 mm softwood floor * Bolted smooth sheet steel front wall * Fold-down side walls made of trapezoidal-profiled steel sheet with board lifting spring * Rear wall made of steel, insertable between the ramp holders for storage in front of the front wall when not in use * Rear stanchions bolted ----Load Securing: * Perforated outer frame, approx. 45-degree bent, with 2 t lashing capacity every 480 mm * Installation of 3 t recessed lashing rings every 600 mm possible * In each corner front and rear, 1 x 6.3 t lashing ring * Various holes in front and rear crossmembers for 1.2 t lashing options ----Ramps: * One-piece mechanical grating loading ramps with spring system for single-person operation, approx. 2,750 x 600 mm (collapsible to 20 mm) * Rear approach angle approx. 860 mm chassis Nodpfjl Th Ncjx Af Aewc ----Tyres: * Tyres 235/75 R 17.5 ----Wheelbase: * Wheelbase: 990 mm ----Paintwork: * Drawbar, front wall, tailgate, folding supports, loading ramps galvanized * Axles, springs, air tanks, 40 mm flange towing eye painted in black * Board walls painted in RAL2011 deep orange * Side panels available in other RAL colors at extra cost ----Information: * New vehicle with manufacturer warranty * Errors and prior sale excepted ----Delivery Time: * Immediately available ex works Egestorf

Stanje: novo, največja dovoljena obremenitev: 8.870 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-ER 11.9: ----Braking System: * Electronic braking system (EBS) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 5.5 t Gigant axle units ----Suspension: * Parabolic springs with balancing unit ----Drawbar / Flange Eye: * Drawbar height adjustable by approx. 300 mm * 40 mm flange towing eye ----General Attachments: * Jost mechanical landing gear at front * Bolt-on, hot-dip galvanized folding supports at rear (external) * Side underrun protection * Plastic quarter mudguards * Plastic toolbox on front right, externally mounted on front wall ----Electrics / Lighting: * Tyre pressure monitoring system (TPMS) * 15-pin power connector * LED tail lights ----Load Area: * 50 mm softwood floor * 20" container locks mounted at front and rear * Bolted bulkhead made of smooth steel sheet * Drop sides made of trapezoidal-profile steel sheet, foldable with sideboard spring lifter * Hot-dip galvanized bolted rear stanchions ----Load Securing: * Perforated outer rail, edged at approx. 45°, with lashing capacity of 2 t every 480 mm * Optional 3 t folding lashing brackets every 600 mm (five lashing rings mounted per side) * One 6.3 t lashing ring in each corner, front and rear * Various bores in front and rear crossmembers for 1.2 t lashing points ----Ramps: * 1 pair of aluminium loading ramps, approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles Nsdpfel Tilxex Af Aewc * Rear storage compartment recessed into the chassis frame under the loading area ----Paintwork: * Hot-dip galvanized chassis, drawbar, bulkhead, and rear wall * Sideboard colour in RAL 9010 pure white * Painting of side walls in a RAL colour of choice available at extra charge ----Information: * New vehicle, not registered * Subject to errors and prior sale ----Delivery Time: * Available immediately from Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 22.000 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2008, Oprema: ABS, Vehicle identification number: WMM0000080052540 STRAIGHT LOADING PLATFORM Container locking device Unladen weight: 8,000 kg German roadworthiness test (HU): due Gigant axles with drum brakes Air suspension Platform dimensions: 9,400 mm – Loading height: 880 mm – For further measurements see image No. 4 Extendable to 3,000 mm with lighting Drawbar – 50 mm Hydraulic ramps, split – Length: 2,600 + 1,600 mm – Width: 650 mm Support legs Tyres: 235/75 R 17.5 Nwjdpfxstuhv Ro Af Aec Subject to prior sale, modifications, and errors. This description serves for general identification of the vehicle only and does not constitute a warranty in the legal sense. The details specified in the sales contract are binding. Our offer generally does not include a new roadworthiness test (TÜV). If a new inspection is required, we will be happy to provide an offer from our partner workshops. Vehicle may feature advertising decals and/or inscriptions. Our general terms and conditions of delivery and payment apply.

Stanje: rabljeno, prva registracija: 06/2010, dolžina tovornega prostora: 11.350 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 950 mm, - Krmiljena os - Daljinsko upravljanje - Hidravlične rampe - Zgornja nakladalna površina 3500 mm - Spodnja nakladalna površina 7850 mm Nsdpox Dzn Uefx Af Aswc

Stanje: novo, največja dovoljena obremenitev: 8.780 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2024, * KA-TA-R 11.9 Masterline: ----Brakes: * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem equalization unit ----Drawbar / Flange Eye: * Height-adjustable hot-dip galvanized drawbar, adjustable by 300 mm, with 40 mm flange eye Nedpfopk D D Uex Af Ajwc ----General Attachments: * Jost mechanical landing gear (front) * Two rear mechanical hot-dip galvanized fold-down supports * Tool box made of galvanized steel sheet, mounted right side * Plastic quarter mudguards ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin electrical connector * Bolted underride guard with LED tail lights ----Tipping Platform: * Net hooks on the sides and rear in the central locking mounts as well as 3 external on the front wall * Hot-dip galvanized chassis * Steel pallet 3-way tipper body, fully galvanized * Continuous, drop-side walls with spring-assisted board wall lifters, can be folded down—no center stanchions * Tailgate foldable and pendulum-mounted via manual central locking * Hot-dip galvanized bolted rear stanchion ----Load Securing: * 1 recessed and foldable 5 t lashing ring in each corner, as well as 4 recessed and foldable 3 t lashing rings on each side in the outer frame * 4 mm steel sheet floor, rear mount rail for ramps ----Ramps: * 1 pair aluminum loading ramps approx. 3,570 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment under the loading area at the rear, integrated into the chassis ----Tires: * 235/75 R 17.5 tires ----Paint Finish: * Axles, springs, air tanks, drawbar and landing gear painted in black * Vehicle is hot-dip galvanized ----Notes: * Reinforced body with load securing certificate according to EN 12642 XL * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery Time: * Available immediately from Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 8.780 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2024, * KA-TA-R 11.9 Masterline: ----Brakes: * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem equalization unit ----Drawbar / Flange Eye: * Height-adjustable hot-dip galvanized drawbar, adjustable by 300 mm, with 40 mm flange eye ----General Attachments: * Jost mechanical landing gear (front) * Two rear mechanical hot-dip galvanized fold-down supports * Tool box made of galvanized steel sheet, mounted right side * Plastic quarter mudguards ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin electrical connector * Bolted underride guard with LED tail lights ----Tipping Platform: * Net hooks on the sides and rear in the central locking mounts as well as 3 external on the front wall * Hot-dip galvanized chassis * Steel pallet 3-way tipper body, fully galvanized * Continuous, drop-side walls with spring-assisted board wall lifters, can be folded down—no center stanchions * Tailgate foldable and pendulum-mounted via manual central locking * Hot-dip galvanized bolted rear stanchion ----Load Securing: * 1 recessed and foldable 5 t lashing ring in each corner, as well as 4 recessed and foldable 3 t lashing rings on each side in the outer frame * 4 mm steel sheet floor, rear mount rail for ramps ----Ramps: * 1 pair aluminum loading ramps approx. 3,570 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment under the loading area at the rear, integrated into the chassis Nwjdpfspk D Dmox Af Asc ----Tires: * 235/75 R 17.5 tires ----Paint Finish: * Axles, springs, air tanks, drawbar and landing gear painted in black * Vehicle is hot-dip galvanized ----Notes: * Reinforced body with load securing certificate according to EN 12642 XL * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery Time: * Available immediately from Egestorf on the A7

Stanje: rabljeno, številka stroja/vozila: 110, lastna masa: 8.320 kg, največja dovoljena obremenitev: 31.680 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2008, dolžina tovornega prostora: 10.300 mm, širina tovornega prostora: 2.550 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 r17,5, medosna razdalja: 6.500 mm, barva: modra, Oprema: ABS, * Drum brake * 4 axles * Wheelbase 6,500 mm Nodpfslpav Ujx Af Aowc * Hydraulic ramp length 2,850 mm – width 650 mm * Loading edge height 920 mm * Extendable to 3 m Subject to errors and omissions

Stanje: rabljeno, Leto izdelave: 2010, Vakuumska cisterna pribl. 6 m³, primerna za Müller-Mitteltal CHK. Vključno z vakuumsko črpalko na pogon preko kardanske gredi ter različnimi cevmi. Vakuumska črpalka = Dodatne informacije = Nwsdex Nl Npjpfx Af Aoc Za več informacij se obrnite na Jan-Marc Schwickert.

Stanje: rabljeno, Leto izdelave: 2013, Različni kontejnerji za Müller-Mitteltal CHK: - 7 kosov 4,5 - 5 m³, cena na kos 1.000,- € - 3 kosi 8 m³, cena na kos 2.000,- € Vsi kontejnerji so v uporabnem stanju. Letniki 2013 - 2015. = Dodatne informacije = Država proizvodnje: DE Nwedpfx Aoxb N A Isf Aoc Za več informacij kontaktirajte Jan-Marc Schwickert.