Müller-Mitteltal Kwh 9,9 Kabeltransport-Anhänger Mit Dieselmotor nakup rabljenega (13.083)

Stanje: novo, največja dovoljena obremenitev: 30.080 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – without truck-side installation * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning panel packages front & rear * SmartBord infotool installed with pressure sensors for total axle load display per axle group * Reflective contour tape on the sides and rear * LED rotating beacon (removable) at the rear * 15-pin power connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front closed single plastic mudguards * Straight rear steel mudflaps, each with spray suppression * Side underrun protection * Superstructure in front of the bogie platform approx. 520 mm with 45° corners and 3 storage compartments including lockable folding lids (folding lids opening to the rear) * Chassis made from high-strength fine-grained steel * Floor over the bogie platform made of 50 mm softwood, and 60 mm softwood in the low loader platform * Outer planks of the drive-on ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing eyes 6.4 t front left and right on the main frame of the bogie platform, 1 pair each of 13.4 t lashing rings at the front and rear outer frame, 1 pair each of 10 t lashing rings, swiveling and lowerable, loadable in all directions and recessed in the outer frame, 5 t lashing rings bolted to the outer frame of the wheel recesses (2 at the front recess, 1 at the rear), 2 pairs of 6.4 t lashing rings on the excavator stick holder * 11 pairs of folding outriggers for a total width of 3 meters (not at the rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for the widening boards made of sheet steel, mounted transversely to the loading area in front of the first rear axle * Excavator stick holder above the rear axle up to the end of the approach slope approx. 2,300 x 740 x 190 mm * Two wheel recesses per side approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with retractable cover (storage for covers at the front on the bogie platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm * Hydraulic lateral ramp shift * Loading area over the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loading height loaded approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, bogie, folding outriggers, rear drop-down supports, and drive-on ramps galvanised Cjdpfxsxmpyde Al Hsgt * Axles, air tanks, and drawbar painted in black * Tires: 235/75R17.5 * Vehicle is galvanised * New vehicle with manufacturer’s warranty * Errors and prior sale reserved * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 30.080 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning sign packages front & rear * SmartBord infotool installed with pressure sensors for displaying axle group loads * Reflective contour tape on the sides and rear * LED beacon (removable) at the rear * 15-pin electrical connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front enclosed individual plastic mudguards * Rear straight steel mudflaps with spray suppression * Side underrun protection * Extension in front of the bogie platform approx. 520 mm with 45° corners and 3 storage compartments with lockable folding lids (folding lids open towards the rear) * Chassis made from high-strength fine-grain steel * Floor over bogie platform made of 50 mm softwood, and in the low-bed platform made of 60 mm softwood Cedpfxjxmpykj Al Hegt * Outer planks of the ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing eyes 6.4 t each at the front left and right on the main frame of the bogie platform; one pair of 13.4 t lashing rings at the front and rear sides of outer frame; one pair of 10 t lashing rings on each side foldable and lowerable, loadable in all directions, integrated into the side frame; 5 t bolted lashing rings on the outer frame of the wheel recesses (2 per front wheel recess, 1 per rear); 2 pairs of 6.4 t lashing rings at the excavator stick compartment * 11 pairs of fold-out outriggers for overall width of 3 m (not on the rear incline) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for width-extension planks, steel, mounted crosswise to the loading area in front of the first rear axle * Excavator stick compartment above the rear axle extending to the end of the ramp incline, approx. 2,300 x 740 x 190 mm * Two wheel recesses per side approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with retractable cover (storage for covers at the front on bogie platform) for transporting wheel loaders with wheelbase 3,100 – 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulic extendable tip, approx. 4,650 x 720 mm * Hydraulic sideward ramp displacement * Loading area above the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded deck height approx. 890 mm ± 20 mm (including 860 mm ramp incline) * Chassis, bogie, fold-out outriggers, rear supports, and access ramps fully hot-dip galvanized * Axles, air tanks, and drawbar painted in black shade * Tires: 235/75R17.5 * Vehicle is fully hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 38.620 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, T5 Profile 50.0: ----Brakes: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (ride height +30 mm when axle is lifted) * Last axle self-steering (lockable from the driver's cab for maneuvering purposes without the need for truck-side installation; additionally lockable via switch on trailer). Deactivate the lock before driving on public roads. * Forced lifting and lowering of the lift axle for maneuvering purposes (truck-side installation required), with speed-dependent control via EBS electronics ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: * Drawbar, 1,500 mm long with 50 mm towing eye and manual height adjustment ----Electrics / Lighting: * Smartboard as infotool with pressure sensors for total axle load display per axle group * Tire pressure monitoring with indication in the truck via EBS signal (no truck-side installation necessary) * LED lighting system 12/24 V * Removable rear LED beacon ----General Accessories: * Mechanical warning plate kit for 3 m total width * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm, mounted side left * Front axle with plastic mudguards, rear with galvanized steel mudguard skirts ----Low Loader Platform: * Front section of turntable platform with 45° angles and 3 storage compartments with lockable, rear-hinged covers * Shortening of the lowbed platform by 500 mm to 6,280 mm including extended step by 500 mm to the front * Rubber covering on folding frame, drive-on ramp and running surface of the low-loader platform * Bamboo wood between the longitudinal beams in front of the excavator arm rest ----Load Securing (LaSi Package): * 2 x 6.4 t lashing rings at front corners * 2 x 13.4 t UVV lashing points each at side front and rear corners Cjdpfxol Tihus Al Hjgt * 5 x 10 t UVV lashing rings per side (pivoting and lowerable, loadable in all directions) * 4 stake pockets per side with additional 2 t lashing capability each * 1 x 16 t UVV lashing ring on the rear cross member ----Widening: * Extendable and foldable widening outriggers for 3 m total width (beam holders under chassis, right side) ----Excavator Arm Rest: * Continuous excavator arm rest with reinforcement profile from last axle to tow bar approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on sides of arm rest ----Ramps: * Hydraulic folding ramp with dual-line hydraulics and extendable tip piece approx. 4,650 x 720 mm including load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (required in case of hydraulic pump output on truck over 40 l/min up to max. 140 l/min) ----Loading Height: * Loaded: 890 mm +/- 20 mm via air suspension ----Platform Dimensions: * Platform over turntable: 2,600 + 390 x 2,520 mm * Lowbed platform: 6,280 + 500 x 2,520 mm incl. 860 mm inclines ----Paintwork: * Chassis, turntable, drawbar, widening consoles, and ramps hot-dip galvanized * Tow bar, axles, hydraulic axle supports, and air tanks painted in black ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available immediately*

Stanje: novo, največja dovoljena obremenitev: 38.620 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, T5 Profile 50.0: ----Braking System: * Wabco EBS (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (when lifted, ride height +30 mm) * Last axle is self-steering (lockable from the cab for maneuvering purposes without any installation on the truck side, and additionally via a switch on the trailer). The lock must be disengaged before driving on public roads. * Forced lifting and lowering of the lift axle for maneuvering (truck-side installation required), with speed-dependent control via the EBS electronics ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: Drawbar 1,500 mm long with 50 mm draw eye and manual height adjustment ----Electrics / Lighting: * Smartboard as an info tool with pressure sensors for axle load indication per axle group * Tire pressure monitoring with display in the truck via EBS signal (without truck-side installation) * LED lighting system 12/24 V * LED rotating beacon (removable), rear ----General Fittings: * Mechanical warning sign set for 3 m total width * Toolbox made of galvanized steel plate approx. 650 x 300 x 600 mm, mounted left side * Plastic fenders front axle and galvanized steel mudguards rear axle ----Low Loader Platform: * Front section of turntable platform with 45° corners and 3 stowage compartments with lockable folding lids (folding towards the rear) * Shortening of the low-bed platform by 500 mm to 6,280 mm including extended recess by 500 mm at the front * Rubber covering on the folding frame, approach ramp, and running surface of the low-loader platform * Bamboo wood between the longitudinal beams, in front of the excavator stick rest area ----Load Securing (LaSi Package): * 2 x 6.4 t lashing eyes in the front corners * 2 x 13.4 t UVV lashing points on each side in the front and rear corners * 5 x 10 t UVV lashing rings on each side (swivelable and lowerable, loadable in all directions) * 4 stake pockets per side with simultaneous 2 t lashing option * 1 x 16 t UVV lashing ring on the rear crossmember ----Width Extension: * Extendable and foldable width supports for 3 m total width (plank holder under the chassis, right side) ----Excavator Stick Rest: * Continuous excavator stick rest with reinforcement profile from last axle to end beam approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on the sides of the excavator stick rest ----Ramps: * Hydraulic folding ramp with dual-circuit hydraulics and folding tip approx. 4,650 x 720 mm, including load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (for hydraulic pump outputs on the truck over 40 l/min up to max. 140 l/min) ----Loading Height: * Loaded: 890 mm +/- 20 mm adjustable via air suspension ----Loading Area Dimensions: * Platform above turntable: 2,600 + 390 x 2,520 mm * Low-bed loading platform: 6,280 + 500 x 2,520 mm, incl. 860 mm approach ramp ----Paintwork: Cjdpoxptn Dofx Al Hjgt * Chassis, turntable, drawbar, width extension consoles, ramps hot-dip galvanized * Drawbar yoke, axles, hydraulic axle supports and air tanks painted in black ----Information: * New vehicle with manufacturer warranty * Subject to prior sale and errors ----Delivery Time: Available immediately*

Stanje: rabljeno, konfiguracija osi: 1 os, prva registracija: 08/1993, Leto izdelave: 1993, Oprema: ABS, = Further Options and Equipment = - Electronic Braking System (EBS) = Notes = Müller-Mitteltal KA-TA Tipping Trailer Single axle Air suspension ABS Tyres 60% Processing We look forward to welcoming you for a consultation, contract signing, or vehicle collection at our dealership. Please schedule an appointment. If you are unable to visit us in person, we offer complete processing via phone, e-mail, WhatsApp, or fax. On request, we can deliver your new vehicle directly to your door. This means you benefit from the best price, maximum security, and convenience during your transaction. We are also happy to take your used vehicle in part exchange. We offer a digital vehicle appraisal based on your photos, even without you visiting our dealership. Our dedicated purchasing team guarantees you the highest price. Upon request, we can deliver your new 'used' vehicle nationwide, directly to your doorstep, and collect your trade-in vehicle. Financing - Leasing Immediate approval and old loan settlement Your specialist partner for passenger cars, transporters, commercial vehicles, and construction machinery ITC GmbH & Co KG Siemensstraße 7 32312 Lübbecke (Industrial estate) Over 400 vehicles in stock at all times The information provided in advertisements, on the internet, on price tags and in images are non-binding descriptions and do not constitute guaranteed characteristics. The seller accepts no liability or warranty for typographical and data transmission errors. Listed equipment should be checked separately if necessary. The offer is generally without a new MOT; we are happy to provide a quote for an inspection at our partner workshop. Subject to errors and prior sale. Cgodpfx Aljxt Sl Nj Hjt = Further Information = Unladen weight: 3,700 kg Payload: 9,300 kg gross vehicle weight: 13,000 kg

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 03/2004, Leto izdelave: 2004, Oprema: ABS, = Additional options and equipment = - Electronic Braking System (EBS) = Notes = Müller-Mitteltal RAK German vehicle Roll-off trailer 2-axle Air suspension ABS Tyres 60% ID no. 709 We look forward to advising you, signing contracts, or handing over the vehicle at our dealership. Please make an appointment. If you are unable to visit our showroom, we offer complete processing by phone, email, WhatsApp, or fax. On request, we deliver your new vehicle directly to your door. This means you get the best price as well as maximum safety and convenience with your purchase. We are happy to take your used vehicle as a trade-in. We offer you the option of a digital vehicle appraisal based on your vehicle photos, even without visiting the dealership. Our specialised purchasing team offers you a guaranteed top price. Upon request, we deliver your new ‘used’ vehicle nationwide directly to your doorstep and take your trade-in back with us. Financing – leasing Immediate approval and settlement of existing loans. Your specialist partner for passenger cars, vans, commercial vehicles, and construction machinery. ITC GmbH & Co KG Cjdpfxjxyx Hao Al Hegt Siemensstraße 7 32312 Lübbecke (industrial area) Over 400 vehicles in stock at all times. The information given in advertisements, on the internet, on price labels, and in pictures are non-binding descriptions and do not constitute guaranteed characteristics. The seller assumes no liability/warranty for typing or data transmission errors. Listed equipment may need to be checked separately by the buyer. Offer is generally without new TÜV approval; we will gladly provide you with an offer from our partner workshop. Subject to errors and prior sale. = Further information = Unladen weight: 4,850 kg Payload: 13,150 kg Gross vehicle weight: 18,000 kg

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 04/2005, Leto izdelave: 2005, Oprema: ABS, = Further Options and Equipment = - Electronic Braking System (EBS) = Notes = Müller-Mitteltal KA-TA 18 We look forward to advising you. Contract signing or vehicle collection takes place at our dealership. Please arrange an appointment. If you are unable to visit us in person, we can handle the entire process via telephone, email, WhatsApp, or fax. On request, we can deliver your new vehicle directly to your doorstep. This ensures you get the best price, maximum security, and convenience when taking delivery. We are happy to take your used vehicle in part exchange. We also offer digital vehicle appraisal based on your photos, without requiring a visit to our dealership. Our specialized purchasing team guarantees you the highest possible price. If you wish, we can deliver your new used vehicle nationwide right to your door and collect your trade-in at the same time. Csdpfx Aloxt Tf Rj Hogt Financing and leasing available — immediate approval and settlement of your existing loan. Your expert partner for passenger cars, transporters, commercial vehicles, and construction machinery: ITC GmbH & Co. KG Siemensstraße 7 32312 Lübbecke (industrial area) Always over 400 vehicles in stock. All details in advertisements, online listings, price tags, and pictures are non-binding descriptions and do not constitute guaranteed features. The seller assumes no liability or warranty for typographical or data transmission errors. Listed equipment must be individually verified where applicable. This offer does not include a new TÜV inspection; we are happy to provide an offer for a TÜV inspection through our partner workshop. Subject to error and prior sale. Information available in German. = Further Information = Unladen weight: 4,080 kg Payload: 13,920 kg Gross vehicle weight: 18,000 kg

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 08/1996, Leto izdelave: 1996, Oprema: ABS, = Additional Options and Equipment = - Electronic Braking System (EBS) = Remarks = Müller-Mitteltal Trailer ATL Roll-off trailer 2-axle Air suspension ABS Tyres 60% Information available in German We look forward to advising you Contract signing or vehicle collection at our dealership. Please arrange an appointment If you are unable to visit our dealership in person, we offer complete processing via telephone/email/WhatsApp/fax On request, we can deliver your new vehicle directly to your door This means best price for you, maximum security and convenience during acceptance We are happy to accept your used vehicle as part-exchange We offer the option of digital vehicle evaluation based on your vehicle photos even without a dealership visit Cgedpfx Aoxt Sd Eol Hot Our specialised purchasing team offers you a guaranteed top price On request, we deliver your new used vehicle nationwide directly to your door, and collect your trade-in for financing or leasing Immediate approval and settlement of existing credit Your specialist partner for cars, transporters, commercial vehicles, and construction machinery ITC GmbH & Co KG Siemensstraße 7 32312 Lübbecke (Industrial Area) Over 400 vehicles permanently in stock The details provided in advertisements, on the internet, price tags, and images are non-binding descriptions and do not constitute guaranteed characteristics. The seller accepts no liability/warranty for typing or data transmission errors. Listed equipment may need to be checked separately. Our offer generally does not include new TÜV approval; we are happy to make you a quote with our partner workshop. Subject to errors and prior sale = Additional Information = Unladen weight: 2,360 kg Payload: 10,640 kg Gross vehicle weight: 13,000 kg

Stanje: novo, največja dovoljena obremenitev: 11.050 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, * Müller-Mitteltal KA-TA-R 14.4 Tandem Low-Loader Three-Way Tipper Trailer with Ramps * NEW VEHICLE * Available mid-May 2026 in RAL 9016 traffic white * Leasing, financing, and trade-in of your old trailer possible * Reference number for inquiries: 30505 * Remote diagnosis unit (RDÜ) with display option in the truck via EBS signal * Side marker lights with indicator activation * GVW: 14,400 kg, payload: 11,050 kg Cedpjyvxg Isfx Al Hsgt * EBS 2S/2M * Galvanized floor, 5m x 2.42m x 0.5m, drop side panels, laser-welded, pendulum-mounted, fold-down and removable, prepared for later retrofitting of side wall extensions * Lockable compartment under the tipping bridge for access ramp * Incl. 1 pair of aluminum loading ramps, 8t/pair, 3.57m * Galvanized chassis, galvanized front wall * 4 UVV lashing rings LC 5,000daN at front and rear + 8 recessed and foldable lashing points LC 3,000daN in tipping floor (centered) * Hardwood excavator bucket rest * Two-step access in front of the front wall (galvanized) * Stepless height-adjustable drawbar, galvanized, 40mm towing eye * Wide tires 385/55R 19.5 (4x), parabolic springs * Mesh hooks, rear staking posts bolted, galvanized * Extension cables for rear side panel * Plastic toolbox on right chassis frame * LED lighting system 12 + 24 Volt * 2 LED reversing lights at the rear of the trailer * Hire-purchase price: for example, €549 per month over 60 months, no down payment, no residual value. An offer from our financing partner "FM LeasingPartner". Other terms with/without residual value or down payment available * Request an offer from us! * We are Müller-Mitteltal trading partners * Free delivery to your site possible with timely order! ----Our opening hours: Monday - Thursday: 08:00 - 17:00 Friday: 08:00 - 15:00 Outside of these hours by appointment We speak German, English, Polish, and French. Whatsapp

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profile 30.0: * EBS braking system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical rear axle equalizer * Side underrun protection * Swivel supports at the rear on the chassis frame * Mechanically adjustable warning sign kits at the front and rear * Front: closed plastic mudguards, rear: straight galvanized steel mud flaps, each with splash guards * Contour marking tape, reflective, on sides and rear * Foldable (hot-dip galvanized) tool box cover on the turntable platform * Multi-voltage system * LED tail lights * Rotating beacon (removable) at the rear * Drawbar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin power connector * Four stake pockets each side (no stakes included), also suitable for lashing * Load securing package consisting of: 2 lashing points (6.4 t) at the front left & right on the main frame of the turntable platform, 5 pairs of UVV swivel and retractable lashing rings, loadable in all directions and recessed into the outer frame (13.4 t in corners, otherwise 10 t) * 6 pairs of mechanical folding outriggers for total width of 3 m (not in the rear slant) * Widening planks stored in the center of the loading area * Excavator arm support over rear axle up to the rear cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the sides in the excavator arm support) * Mechanical one-piece ramps with spring mechanism (approx. 3,000 x 720 mm) * Mechanically adjustable lateral ramp displacement * Loading area above the turntable: approx. 1,960 x 2,520 mm * Unladen loading height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height approx. 910 mm (including 860 mm approach incline) * Chassis, turntable, drawbar, and ramps hot-dip galvanized Cgodox Ipa Njpfx Al Hjt * Axles, springs, air tanks, etc. painted black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * -- Gross technical weight of 30,000 kg possible -- * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Subject to prior sale and errors * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profile 30.0: * EBS braking system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic leaf springs * Mechanical rear axle compensation * Side underrun protection * Rear swivel supports on chassis frame * Mechanically adjustable warning panel sets front and rear * Front closed plastic fenders and rear straight galvanized steel skirts, each with splash protection * Contour tapes on sides and rear, reflective * Hinged lid (hot-dip galvanized) for tool box in the bogie platform * Multi-voltage system * LED tail lights * Removable beacon at the rear Codpsx Ipavsfx Al Hogt * Tow bar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin electrical connector * Four stake pockets each side (no stakes present) with simultaneous lashing options * Load securing package consisting of: 2 lashing eyes (6.4 t) at the front left & right on the main frame of the bogie platform, 5 pairs of UVV-compliant lashing rings - swiveling and retractable, loadable in all directions and integrated in the outer frame – 13.4 t at the corners, otherwise 10 t * 6 pairs of mechanical folding outriggers for 3 m overall width (not on rear taper) * Widening planks stored in the center of the loading platform * Excavator arm rest over rear axle up to the rear cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings fitted laterally in the arm rest) * Mechanically operated one-piece loading ramps with spring assembly (approx. 3,000 x 720 mm) * Mechanical lateral ramp adjustment * Loading area above turntable: approx. 1,960 x 2,520 mm * Unladen loading height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height approx. 910 mm (incl. 860 mm drive-on slope) * Chassis, bogie, tow bar, and loading ramps hot-dip galvanized * Axles, springs, air tank, etc., painted in black * 235/75 R17.5 twin tires * 5,900 kg curb weight * --Permissible total weight of 30,000 kg technically possible-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Errors and prior sale reserved * Immediately available ex Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 30.700 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2002, Oprema: ABS, * MüllerMitteltal nizkopodni priklopnik s 4 osmi T40 * 2x krmiljeni vrtljivi osi * Nemška prikolica * pero * hidravlično pomične rampe / levo-desno * deljene preklopne rampe * možnost razširitve * ABS * BPW osi * 40 t * lastna teža: 9300 kg * osne obremenitve = 10 t na os * popolnoma funkcionalen * pnevmatike v redu Cjdpfxjyuri Es Al Hsgt

Stanje: rabljeno, največja dovoljena obremenitev: 9.400 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 07/2020, dolžina tovornega prostora: 6.300 mm, širina tovornega prostora: 2.480 mm, Int.-št.: ZANDT Zelo dobro vzdrževana tandem šasija s kesonom ZANDT Cargo * TAT B 110 * Keson * Ojačano leseno dno * Težko nosilne pritrdilne tirnice * Dvoosna tandem os * Široke pnevmatike * Nastavljiva vlečna kljuka * Največja dovoljena masa 11.900 kg * Zelo dobro stanje Možna je menjava staro za novo Financiranje od 3,99% Pridržujemo si pravico do napak in vmesne prodaje! Podatki v tem oglasu so neobvezujoči opisi in ne predstavljajo zagotovljenih lastnosti. Prodajalec ne prevzema nobene odgovornosti za tipkarske ali prenosne napake. Oprema iz oglasa se preveri posebej. Vsi podatki v oglasih so neobvezujoči! Csdjymuz Uopfx Al Hsgt Dostava po celotni Nemčiji na zahtevo Delovni čas: ponedeljek do četrtek od 9:00-17:00, petek od 9:00-14:00 ali po dogovoru!

Stanje: rabljeno, največja dovoljena obremenitev: 9.400 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 07/2020, dolžina tovornega prostora: 6.300 mm, širina tovornega prostora: 2.480 mm, Int. št.: ZANDT zelo dobro vzdrževana tandem ploščadna prikolica ZANDT Cargo * TAT B 110 * ploščad * ojačan lesen pod * pritrdilne tirnice za težke tovore Cgjdjymuz Ispfx Al Hot * tandem z dvema osema * široke pnevmatike * nastavljivo vlečno oje * dovoljena skupna masa 11.900 kg * zelo dobro stanje Možnost menjave starega za novo Financiranje od 3,99 % Napake in vmesna prodaja pridržane! Podatki v tem oglasu so nezavezujoči opisi in ne veljajo kot zagotovljene lastnosti. Prodajalec ne prevzema odgovornosti za tipkarske napake ali napake pri prenosu podatkov. Oprema, navedena v oglasu, je treba posebej preveriti. Vsi podatki v oglasih so nezavezujoči! Dostava po celotni Nemčiji na zahtevo Delovni čas: ponedeljek do četrtek od 9:00 do 17:00 petek od 9:00 do 14:00 in po dogovoru!!!

Stanje: novo, največja dovoljena obremenitev: 16.500 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal ETÜ-TAR 21 Tandem Low Loader / Flatbed Trailer, drive-over platform Reference No. for enquiries: 27963, available end of March 2026 NEW VEHICLE incl. COC * GVW: 21t, Payload: 16.5t, hot-dip galvanised chassis * Available end of March 2026 * Flatbed version with 400 mm high front wall, ramp safety provide by ramp holding rods and diagonal supports * Version: GVW 21 t, reinforced frame and axle, axle spacing 1,810 mm * Deck height approx. 910 mm loaded / approx. 940 mm unloaded * 7,000 mm loading platform with 400 mm high front wall * Extended ramps: 3,000 mm, one-piece hot-dip galvanised ramps with galvanised grating * Ramp lifters with vertically adjustable springs for easy single-person operation * Load securing package: * 4 UVV-compliant fall-type lashing rings (LC 8,000 daN) mounted to existing hole pattern in 45° outer frame, positioned approx. 1 m from front/rear cross-member * 10 UVV-compliant lashing rings (LC 3,000 daN) retractable in the existing hole grid of the outer frame * 2 UVV lashing rings each at front and rear, recessed in cross-members (LC 10,000 daN) * Additional lashing options via 50 mm (LC 1,200 daN) holes in front and rear cross-members * Fitting provisions for retrofitting container locks * Softwood flooring, 50 mm thick * Air suspension with Gigant axles incl. EBS 2S/2M * Raise and lower function * 235/75 R17.5 (8x), twin tyres with tyre pressure monitoring sensor * 1 plastic toolbox in front of the bulkhead on the right-hand side (direction of travel) * LED lighting system * 7-pin socket on rear, wired for extra-length lighting with tail light (58 R) and ground * 2 LED reversing lights at rear * Flashing side marker lights * Oversize width warning panel * 1 removable LED beacon incl. holder and installation Csdpfx Aljyuq R Uo Hsgt * Foldable rear supports, front support foot with gearbox winch ---- Finance lease sample from our cooperation partner MMV Leasing: €655/month net with 60 months term, no down payment and zero euro balloon payment Other terms possible with/without down payment / residual value. We are MüllerMitteltal authorised dealers. ---- Our opening hours: * Monday-Thursday: 08:00 - 17:00 * Friday: 08:00 - 15:00 * Outside of these hours by appointment We speak German, English, Russian, Polish, and French. Leasing, financing, trade-in possible.

Stanje: novo, največja dovoljena obremenitev: 23.940 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2025, * T3 Profi 30.0: * EBS braking system * RDÜ tire pressure monitoring * Emergency release mechanism for spring brake cylinders * Drum brakes * 3 x 11t Gigant axles * Parabolic springs, mechanical axle compensation at the rear * Side underrun protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning board sets at front and rear * Front: closed plastic mudguards; Rear: straight, galvanized sheet steel skirts, each with spray protection * Reflective contour tape on the sides and rear * Tool box made of galvanized sheet steel, powder-coated black, approx. 650 x 300 x 600 mm * Hinged lid (hot-dip galvanized) for tool box within the turntable platform * Multi-voltage wiring * LED tail lights * Rear warning beacon (detachable) * Drawbar with 50 mm draw eye and height adjustment via tension spring & turnbuckle * 15-pin electrical socket * Four stake pockets per side (stakes not included), also usable as lash points * Load securing package comprising: 2 lashing eyes (6.4 t) at the front left & right on the main frame of the turntable platform, 6 pairs of UVV-certified lashing rings, swiveling and retractable, loadable in all directions, recessed into the outer frame; corner rings: 13.4 t, other rings: 10 t * 6 pairs of mechanical folding extensions for 3 m total width (not at the rear slope) * Widening boards stored at the center of the load floor * One-piece, hot-dip galvanized hydraulic access ramps (approx. 3,000 x 720 mm), manually adjustable sideways * 4-way valve block for hydraulic side ramp retrofit * Platform above turntable: approx. 1,960 x 2,520 mm * Unladen platform height: approx. 1,070 mm * Rear platform: approx. 6,500 x 2,520 mm * Unladen platform height: approx. 910 mm (incl. 860 mm drive-on angle) * Chassis, turntable, drawbar, and access ramps hot-dip galvanized * Axles, springs, air tanks, and related components painted in black Cedpfx Alsl Th I Ao Hegt * 235/75 R 17.5 twin tires * Approx. 5,980 kg unladen weight * Permissible total technical weight: 30,000 kg * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from week 11/2026

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting/lowering system and RtR valve * Smard board for payload weighing * Warning sign kits, front and rear * Reflective contour tape on the sides and rear * Removable rotating beacon (rear) * LED lighting * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated steel sheet and basket-type spare wheel holder, mounted right side * Front: closed single plastic mudguard * Rear: straight steel mudguards, each with spray suppression * Side underrun protection * Bogie platform extension by 520 mm with 45° corners, 3 integrated lockable storage compartments with lids * Chassis made of high-strength fine-grained steel * 50 mm softwood floor over bogie platform, 60 mm softwood on low-bed platform * Outer rails on ramps made of hardwood * 4 stake pockets per side (no stakes included); 2 t lashing possible at each * Load securing package: 2 lashing eyes (6.4 t) front left/right on main frame of bogie platform * 2 pairs of lashing rings (13.4 t) on outer frame front/rear per side; 4 pairs of lashing rings (10 t), swing-out and lowerable per side (front/rear) * All lashing points loadable in all directions and recessed into outer frame * 2 pairs of lashing rings (6.4 t) in excavator arm rest area * 8 pairs of galvanized folding outriggers for 3 m overall width (not at rear slope) * Extension planks stored left side in a storage box * Excavator arm rest above rear axle to end of rear slope, approx. 2,100 x 740 x 190 mm * Rear mechanical fall supports * Hydraulic folding ramps with hydraulically adjustable ramp tip, approx. 4,650 x 720 mm, incl. hydraulic lateral ramp adjustment & load-holding valve * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Loading height loaded approx. 890 mm, +/-20 mm (incl. 860 mm approach slope) * Flow divider installed Cgsdpfol Tik Nox Al Hst * Chassis, bogie, ramps, outriggers and mechanical fall supports hot-dip galvanized * Axles, drawbar, air reservoir and turntable in black finish * Tires: 235/75 R 17.5 * New vehicle, no initial registration, manufacturer’s warranty * Subject to errors and prior sale * Immediately available ex Egestorf, A7

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lift/lowering system and RtR valve * Smard board for load weight determination * Warning sign packages front & rear * Reflective contour marking tapes on sides and rear * Rotating beacon (removable) at rear * LED lights * Straight drawbar with 50 mm towing eye and continuously adjustable height * Tool box made of powder-coated sheet steel and spare wheel holder in basket design, right-hand side * Closed single plastic mudguards at front * Straight rear steel splash guards, each with spray suppression * Side underrun protection * Turntable platform front extension by 520 mm with 45° corners and 3 flush storage compartments with lids, lockable * Chassis made of high-strength fine-grained steel * Decking above turntable platform: 50 mm softwood, in low-bed platform: 60 mm softwood * Outer planks of access ramps: hardwood * Each side features 4 stake pockets (stakes not included), with simultaneous 2 t lashing points * Lashing package includes: 2 lashing rings 6.4 t, front left and right on main frame of turntable platform * On sides, front & rear, 2 pairs of 13.4 t lashing rings on outer frame; sides each with 4 pairs of 10 t lashing rings, pivoting & lowerable * Loadable in all directions, recessed in the outer frame * 2 pairs of 6.4 t lashing rings on the excavator stick rest area * 8 pairs of galvanized folding outriggers for 3 m overall width (not in the rear slope) * Extension planks stored left side in a stowage compartment * Excavator stick rest above rear axle to rear slope approx. 2,100 x 740 x 190 mm * Mechanical drop supports, rear * Hydraulic folding ramps with hydraulic tip section approx. 4,650 x 720 mm including lateral hydraulic ramp shift & load holding valve * Load area over turntable: approx. 2,990 x 2,520 mm * Rear load area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm drive-on slope) Cgsdpfxsl Tphrs Al Hot * Flow divider installed * Chassis, turntable, ramps, outrigger arms, and mechanical rear supports hot-dip galvanized * Axles, drawbar, air reservoir, and turntable painted in a black tone * Tires: 235/75 R 17.5 * New vehicle, not previously registered, with manufacturer warranty * Subject to errors and prior sale * Immediately available ex Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 23.940 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profi 30.0: * EBS braking system * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t Gigant axles * Parabolic springs, mechanical rear axle equalization Codpfel Th Nnox Al Hegt * Side underrun protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at front and rear * Front axle: closed plastic mudguards; rear axle: straight, galvanized steel skirts, each with spray protection * Reflective contour marking tape on the sides and rear * Tool box made of galvanized sheet steel – black powder-coated – approx. 650 x 300 x 600 mm * Folding lid (hot-dip galvanized) for the toolbox on the turntable platform * Multi-voltage system * LED tail lights * Rotating beacon (removable) at the rear * Drawbar with 50 mm towing eye and height adjustment via drawbar spring & turnbuckle * 15-pin electrical plug * Four stake pockets on each side (no stakes included), with integrated lashing option * Load securing package consisting of: 2 lashing rings (6.4 t) at the front left & right on the main frame of the turntable platform, 6 pairs of UVV-compliant lashing rings, swiveling and retractable, loadable in all directions and recessed in the outer frame – 13.4 t in the corners, otherwise 10 t. * 6 pairs of mechanical folding outriggers for 3 m overall width (not on the rear slope) * Widening boards stored in the center of the loading area * Hot-dip galvanized one-piece hydraulic ramp (approx. 3,000 x 720 mm), mechanically adjustable sideways * 4-section control valve block for retrofitting hydraulic side ramp shifting * Loading area above turntable: approx. 1,960 x 2,520 mm * Loading height unladen: approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Loading height unladen: approx. 910 mm (including 860 mm approach slope) * Chassis, turntable, drawbar, and ramps hot-dip galvanized * Axles, springs, air tanks etc. painted black * 235/75 R 17.5 twin tires * Approx. 5,980 kg unladen weight * Technical gross vehicle weight of up to 30,000 kg possible * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from week 11/2026

Stanje: rabljeno, največja dovoljena obremenitev: 17.500 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, prva registracija: 09/2005, naslednji pregled (TÜV): 01/2027, širina tovornega prostora: 2.500 mm, ? Hidravlične rampe ? Razširljive ? 8 pritrdilnih ušes na vsaki strani ? Nosilec za rezervno kolo ? Nakladalna višina: ca. 930 mm ? Bobnasta zavora ? Duomatski priključek ? Listnato vzmetenje Cgodpoytz Hwofx Al Het ? Dvojna kolesa Vse informacije brez jamstva / Možen vmesni prodaj.

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-ER 14.4 Flatbed: ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes ----Axles: * 2 x 7 t BPW axles ----Suspension: * Air suspension with lift and lowering system ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (therefore B-dimension approx. 8,080 mm) * 40 mm flange towing eye ---- Electric / Lighting: * 15-pin electrical connector * LED lighting system 12 / 24 V * 2 additional LED reversing lights at the rear (activated by reverse gear) * 1 removable LED beacon (incl. holder) at the rear * TPMS (Tire Pressure Monitoring System) ----General Attachments: * Mechanically adjustable 3 m warning sign sets front and rear * Landing gear at the front * External folding support legs at the rear * Plastic toolboxes approx. 750 x 350 x 300 mm each, mounted to the left and right sides * Lateral underrun protection * Rear underrun protection * Plastic quarter mudguards ----Loading Platform: * 400 mm high bolted front wall * 50 mm softwood floor * 2 pairs of container locks (extendable for 3 m container external width) and lockable, locking dimension retracted to ISO - DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not DIN compliant) with an absolute external width of 3,000 mm. ----Cargo Securing: * Perforated outer frame, angled at approx. 45 degrees, with 2 t lashing force every 480 mm * Option to fit 3 t drop-in lashing rings every 600 mm - 5 x 3 t UVV lashing rings installed per side - Cgedpfx Alsv D Tbks Hjt * In each front and rear corner 1 x 6.3 t lashing ring (front directly behind the container locks in the wooden floor and rear in the end cross member) * Various holes in the front and rear cross member for 1.2 t lashing points ----Ramps: * 1 pair of aluminium slide-in ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tyred and tracked vehicles * Storage compartment from the rear, recessed under the loading platform in the chassis ----Paintwork: * ---Chassis, drawbar, front wall, underrun protection and rear supports hot-dip galvanized--- * Axles, air tanks, front landing gear, and flange towing eye painted in black ----Info: * New vehicle with manufacturer warranty * Subject to errors and prior sale ----Delivery time: * Available from week 22/2026

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-ER 14.4 Flatbed: ----Braking system: * EBS (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t BPW axles ----Suspension: * Air suspension with lift and lowering system ----Drawbar / Flange Drawbar Eye: * Height-adjustable drawbar by 300 mm * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (thus B-dimension of approx. 8,080 mm) * 40 mm flange towing eye ---- Electrics / Lighting: * 15-pin electrical connector * LED lighting system 12/24 V * 2 additional LED reversing lights at the rear (switched via reverse gear) * 1 removable LED beacon (incl. bracket) at the rear * TPMS (Tire Pressure Monitoring System) ----General Attachments: * Mechanically adjustable 3 m warning panel sets front and rear * Support windlass at the front * Outward folding support legs at the rear * Plastic toolboxes approx. 750 x 350 x 300 mm each left & right side * Side impact protection * Underrun protection * Plastic quarter mudguards ----Platform: * 400 mm high bolted front wall * 50 mm softwood floor * 2 pairs of container locks (extendable to 3 m container external width) and lockable, locking dimension retracted according to ISO - DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not according to DIN) for an absolute external width of 3,000 mm ----Load Securing: * Perforated outer frame, angled approx. 45 degrees, with 2 t lashing capacity every 480 mm * Optionally, installation of 3 t lashing shackles every 600 mm - each side equipped with 5 x 3 t UVV lashing shackles - * At each front and rear corner, 1 x 6.3 t lashing ring (front directly behind the container locks in the wood floor and rear in the end crossmember) * Various holes for 1.2 t lashing options in the front and rear crossmembers ----Ramps: * 1 pair of aluminium slide-in ramps approx. 3,570 x 410 mm (load capacity 10 t/pair) suitable for rubber-tyred and tracked vehicles * Rear accessible storage compartment underneath the loading platform, integrated in the chassis ----Painting: Cgedjv D Tbdjpfx Al Hst * ---Chassis, drawbar, front wall, underrun protection and rear supports hot-dip galvanized--- * Axles, air tanks, front support windlass and flange towing eye painted in a shade of black ----Info: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery lead-time: * Available from CW 22/2026

Stanje: rabljeno, največja dovoljena obremenitev: 10.960 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, prva registracija: 11/2024, naslednji pregled (TÜV): 03/2027, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 1.100 mm, skupna širina: 2.550 mm, Dolžina nakladalne površine: 5.000 mm Širina: 2.550 mm / Nakladalna širina ca. 2.500 mm Nakladalna višina: ca. 1.100 mm Dodatne informacije - Jeklo - Vroče cinkano - Aluminijaste naletne rampe - Predal za rampe - 500 mm stranske stranice, preklopne - Vzmeti stranskih stranic - Gigant osi - Pnevmatike 285/70R19,5 - Nastavljiv priklop po višini - Podporna noga spredaj + zadaj - Plastična orodjarnica Cgedpfx Asytma Asl Hst - Vstop spredaj

Stanje: rabljeno, največja dovoljena obremenitev: 29.750 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 03/2010, naslednji pregled (TÜV): 05/2026, Mera-B 11.750 mm Lastna teža 10.250 kg Obremenitev osi 2 x 10.000 kg Nakladalna dolžina nad vrtečo ploščo 2.400 mm vklj. 350 mm poševnine Nakladalna dolžina 7.700 mm vklj. 900 mm poševnine Višina nalaganja 880 mm Širina 2.550 mm, razširljivo na 3.000 mm Utornica za odlaganje izkopalnega kraka (DxŠxV cca 2.500 x 740 x 180 mm) SAF osi z zračno vzmetenjem 2-delne hidravlične rampe, 2.100 mm + 2.000 mm dolge, 650 mm široke vklj. Rampe hidravlično nastavljive Hidravlična podpora zadaj Izsek za kolo za drugo osjo Izsek za sprednje kolo, zgoraj dolžina cca 2.000 mm x 1.100 mm, spodaj globina cca 350 mm Izseki za kolesa med 3. in 4. osjo Izsek za zadnje kolo, zgoraj dolžina cca 1.300 mm x 550 mm, spodaj globina cca 220 mm Csdpfoxpmmmjx Al Hjgt

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal ETÜ-TA-R 14.4 Tandem | Low Loader | Platform | Trailer Available immediately | Reference number for inquiries: 11611 | Delivery to your address possible * We are happy to provide you with an individual offer * ---- * Gross weight: 14.4 t, Payload: 10.95 t * LED lighting system * GIGANT axles, EBS, twin tires 235/75R 17.5, parabolic springs * Tire pressure monitoring system (TPMS) * 6.27 m x 2.47 m platform with galvanized 400 mm front wall * Excavator bucket rest made of hardwood, bolted to the front wall * Floor height unladen 930 mm / laden 870 mm * One-piece ramps with hot-dip galvanized grid surface, slip-resistant design, retractable down to approx. 20 mm. Secured by retaining bar and diagonal brace * Ramp lifter with upright, adjustable springs for easy one-man operation * 4 UVV drop lashings (LC 6300 daN) * Perforated outer frame (45°-bent with hole pattern for lashing equipment, lashing force per lashing point LC 2000 daN at a minimum spacing of 480 mm. Installation of drop lashings LC 3000 daN at approx. 600 mm spacing possible), closely spaced cross-stiffeners, high-ribbed front and rear closure with rear loading ramp, hot-dip galvanized * 10 UVV lashing rings LC 3000 daN retractable in the existing hole grid in the outer frame, additional * Additional lashing options via bore holes (Ø 50 mm, LC 1200 daN) in the front and rear crossmembers * Toolbox in front of the front wall * Side marker lights with indicator function * 50 mm thick softwood floor. Chassis hot-dip galvanized * Height-adjustable landing gear at the front, folding supports at the rear * Retrofitting of 2 container locks possible * Drawbar with 40 mm towing eye (hot-dip galvanized), height adjustable, 50 mm eye possible on request * 1 removable LED warning light at the rear * ---- * Leasing, hire purchase, financing, trade-in possible * Example: 510 euros for 60 months’ term, no down payment, no final installment * ---- * Our opening hours: * Monday - Thursday: 08:00 - 17:00 * Friday: 08:00 - 15:00 Cgedjyndh Hspfx Al Hst Outside of business hours, viewings possible by appointment. We speak German, English, Polish, and French Leasing, financing, trade-in possible