Müller-Mitteltal T4 Tieflader 40To. Hydr. Rampen Verbreiterbar nakup rabljenega (4.414)

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profile 30.0: * EBS braking system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical rear axle equalization * Side underrun protection * Swing supports at the rear of the chassis frame * Mechanically adjustable warning board sets at front and rear * Front axle: enclosed plastic mudguards; rear axle: straight, galvanized steel skirts, each with spray protection * Reflective contour tape on sides and rear Isdpfox Ipb Hjx Ag Ijtg * Folding lid (hot-dip galvanized) for toolbox in the bogie platform * Multi-voltage system * LED rear lights * Rotating beacon (removable) at rear * Drawbar with 40 mm towing eye and height adjustment by draw spring & turnbuckle * 15-pin electrical connector * Four lashing pocket sockets per side (no stakes included) with simultaneous lashing option * Load securing package consisting of: 2 lashing eyes (6.4 t) at the front left & right on the main frame of the bogie platform, 5 pairs of UVV swivel and retractable lashing rings, loadable in all directions and embedded in the outer frame - 13.4 t in the corners, otherwise 10 t * 6 pairs of mechanical folding outriggers for 3 m total width (not in rear slope section) * Widening planks stored in the middle of the loading area * Excavator boom rest over rear axle up to the end cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the sides of the excavator boom rest) * Hydraulic, one-piece drive-on ramps (approx. 3,000 x 720 mm) * Hydraulically adjustable, lateral ramp displacement * Loading area above slewing ring: approx. 1,960 x 2,520 mm * Unladen loading height: approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height: approx. 910 mm (incl. 860 mm drive-on slope) * Chassis, bogie, drawbar and drive-on ramps hot-dip galvanized * Axles, springs, air tanks, etc., painted in black shade * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * -- technically permissible gross weight: 30,000 kg -- * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Errors and prior sale excepted * Available from approx. week 36/2026

Stanje: novo, največja dovoljena obremenitev: 31.900 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release for spring-actuated cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lift/lowering function and RtR valve ----Drawbar: * Straight drawbar with 50 mm towing eye and continuously adjustable height ----Electrics / Lighting: * Tire pressure monitoring system with display option in truck dashboard via EBS signal – no installation required on truck * SmartBoard as infotool with pressure sensors for axle load display per axle group * 15-pin power connector * LED taillights * Removable LED beacon at rear ----General attachments: * Warning plates front & rear * 2 x toolboxes made of galvanized, powder-coated sheet steel approx. 650 x 300 x 600 mm, right side * Closed single plastic mudguards at front * Straight steel spray suppression panels at rear, each with spray suppression * Side underrun protection ----Low-bed platform: * Turntable/platform extension by 520 mm with 45° corners and 3 recessed storage compartments incl. lids and lockable * Flooring on turntable platform made of 50 mm softwood; on low-bed platform made of 60 mm softwood * 20 mm rubber covering instead of timber in drive lane area with a well length of 6,780 mm including sloped ramp * Rubber coating on the ramp left and right, approx. 860 mm length * 4 stake pockets per side (stakes not included) with simultaneous 2 t lashing point capability ----Chassis: * Chassis made of high-strength fine-grain steel Itedpfx Asylfvgsg Ieg ----Load securing (Lasi package): Turntable/platform: * 2 pairs of 13.4 t lashing eyes in outer frame of turntable/platform Low-bed: * 4 pairs of 10 t lashing rings per side on the outer frame, foldable and loadable in all directions * 2 pairs of 13.4 t swiveling lashing rings at rear on each side ----Ramps: * Rubber covering on foldable access ramps * Hydraulic folding ramps with hydraulic tip extension approx. 4,650 x 720 mm * Hydraulically lateral ramp shift & load-holding valves ----Rear support: * Hydraulic rear support ----Widening: * 8 pairs of galvanized folding outriggers for 3 m overall width (not on rear bevel) * Widening boards stowed on left side compartment ----Excavator boom trough: * Excavator boom trough above rear axle to end of slope approx. L=2,100 mm x W=740 x D=190 mm * 2 pairs of 6.4 t lashing rings at sides in excavator trough ----Hydraulics: * Hydraulic flow divider in trailer (for truck hydraulic pump outlet above 40 up to max. 120 ltr./min.) ----Loading dimensions: * Rear loading platform: approx. 6,780 x 2,520 mm (incl. 860 mm ramp) * Platform above turntable: approx. 2,990 x 2,520 mm ----Loading height: * Loaded approx. 890 mm, +/- 20 mm ----Paintwork: * Reflective contour tape at sides and rear * Chassis, turntable, access ramps and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks and turntable painted in black tone ----Info: * New vehicle with manufacturer warranty * Errors and prior sale reserved * Sample images may show special equipment ----Lead time: * Vehicle available from approx. week 23/2026

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Rear axle steered with electro-pneumatic steering lock ----Suspension: * Air suspension with lift and lowering system, including RtR valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control box mounted on trailer as info tool with pressure sensors for total axle load display * 15-pin electrical connector * LED lighting system 12/24V * Removable LED beacon, rear left ----General Attachments: * Side underrun protection * Support legs at the front and mechanical swivel supports at the rear of the chassis * Straight pressed steel fenders * Spare wheel holder under the chassis, right side ----Low Loader Deck: * Fifth wheel platform with 45° chamfered front corners and front toolbox made of galvanized steel sheet, W = 2,480 x H = 500 x L = 665 mm, with folding lid * 400 mm aluminium side boards (RAL 9010 pure white) on the fifth wheel platform, foldable and removable * Rear board plug-in, 150 mm high * Rear slope on fifth wheel platform to low-bed approx. 700 mm long * Fifth wheel platform with 50 mm timber planks, low-bed deck with 60 mm timber planks * Tread plate above the axles ----Widenings: * 8 x mechanical folding extensions to a total width of 3 meters (not on rear slope; extension planks available with storage on the platform) * Mechanically adjustable warning panel sets front and rear ----Load Securing (Lashing Package): * On the fifth wheel platform: 2 x 6.3 t lashing rings on each side, plus 3 x 5 t lashing bars per side in the outer frame * On the low-bed platform: 2 x 13.4 t lashing rings per side, plus 4 x 10 t lashing rings, pivotable and lowerable, recessed in the outer frame * 2 x 6.4 t lashing eyes per side, plus 1 lashing ring at the excavator arm rest * 2 x container locks directly after the neck in the low-bed platform ----Excavator Arm Rest: * Continuous excavator arm rest from end of last fixed axle over steering axle to end crossbeam, with internal reinforcements, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Ramps: * Mechanical one-piece hot-dip galvanized hydraulic ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way control block for later customer-side retrofitting of hydraulic ramp shifting * Outer board on ramp made from 50 mm hardwood * Climbing strips on outer frame of ramp and on approach slope * Rubber matting on ramp and approach slope ----Hydraulics: * Hydraulic flow divider in trailer (for hydraulic pump performance in the truck between 40 l/min and 120 l/min) ----Loading Dimensions: * Fifth wheel platform loading area: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Unladen loading height: approx. 910 mm (incl. 860 mm approach slope) ----Fifth Wheel Height: * approx. 1,220 mm (suitable for 2- and 3-axle tractor units) Itedey Ngzyspfx Ag Ieg ----Coating: * Chassis, ramps, rear folding supports, extension consoles hot-dip galvanized * Axles, support legs, air tanks painted in a black shade * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Sample images may show equipment not included with the offered vehicle ----Delivery time: * available from c

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes Ijdpfey Ngz Hsx Ag Iotg ----Axles: * 3 x 11 t BPW Eco Plus axles * Last axle trailing steered with electro-pneumatic steering lock ----Suspension: * Air suspension with lift-and-lower function and RtR valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control box mounted on the trailer as an infotool with pressure sensors for total axle load display * 15-pin power connector * LED lighting system 12 / 24V * Removable LED beacon, rear left ----General Attachments: * Side underrun protection * Landing gears at the front as well as mechanical swing-down supports at the rear of the chassis * Straight sheet steel mudguards * Spare wheel holder under the chassis on the right side ----Low Loader Deck: * Gooseneck platform with 45° chamfered front corners and front toolbox made of galvanized sheet steel W = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm aluminium side boards (RAL 9010 pure white) on the gooseneck, foldable and removable * Rear wall – 150 mm – fitted * Rear slope at the gooseneck platform to the low-bed approx. 700 mm long * Gooseneck platform with 50 mm timber planks, low-bed platform with 60 mm timber planks * Tread plate over the axles ----Extensions: * 8 x mechanical fold-out extensions to 3 m total width, but not on the rear slope (extension planks present with storage on gooseneck platform) * Mechanically adjustable warning sign packages front and rear ----Load Securing (Lashing Package): * On the gooseneck platform: 2 x 6.3 t lashing rings each side and 3 x 5 t lashing bars per side in the outer frame * On the low-bed platform sides: 2 x 13.4 t lashing rings each, and 4 x 10 t swivel and lowerable lashing rings recessed in the outer frame * 2 x 6.4 t lashing eyes per side and rear 1 lashing ring in the excavator arm recess * 2 x container locks directly after the gooseneck in the low-bed platform ----Excavator Arm Recess: * Excavator arm recess from end of last rigid axle, over steering axle to end crossmember, continuous, with internal reinforcement profile, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Loading Ramps: * Mechanically one-piece hot-dip galvanized hydraulic loading ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way control block for later customer retrofit of hydraulic ramp shifting * The outer board of the ramp consists of 50 mm hardwood * Climbing strips on the outer frame of the ramp as well as on the drive-up slope * Rubber on the ramp and drive-up slope ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump capacity in the truck from 40 up to 120 l/min) ----Loading Dimensions: * Loading area, gooseneck platform: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Loading height unladen approx. 910 mm (incl. 860 mm drive-up slope) ----Fifth Wheel Height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractor units) ----Paintwork: * Chassis, loading ramps, rear folding supports, extension brackets hot-dip galvanized * Axles, landing gears, air reservoirs painted in a black tone * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Sample images may include features not part of the offered vehicle * Sample images ----Delivery time: * tba

Stanje: novo, največja dovoljena obremenitev: 13.500 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, * TRA-Kombi 18.0: * 3 in 1 = for roll-off containers, skip containers, and as a low-loader ----Brakes: * TPMS (Tire Pressure Monitoring System) * EBS-E (Electronic Braking System) * Emergency release device for spring brake cylinders ----Axles: * 2 x 12 t Gigant axles ----Suspension: * Parabolic springs ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long * 40 mm towing eye and height adjustment device ----Electrical / Lighting: * LED tail lights * 15-pin power connector * TPMS, display option in the truck via EBS signal (no truck-side installation required) ----General Attachments: * Tool box made of powder-coated sheet steel, right side * Side underrun protection * Plastic quarter mudguards with spray protection * Storage box for container nets, made of galvanized sheet, approx. 960 x 300 x 400 / 450 mm, right side * Plastic rear collision protection buffers * Mechanical drop-down supports at the rear ----Loading Area: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) to guide roll containers * Steel floor with roller recesses in the bogie area * For roll-off container transport, possible container length from 5,500 to 7,000 mm * Pneumatic 4-point clamp locking as well as mechanically insertable stop angles at the front in the track, load securing certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. 10 m³ volume possible * Includes 8 removable skip stops for lateral centering of the skips, front 4 skip stops inserted with pendulum mount * Weld bead as anti-slip coating in the ramp area ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the side for attaching tension elements for positive and non-positive securing of the skips * 4 lashing bars each, cloverleaf design (side) * 1 pair of 13.4 t UVV lashing rings to the front ----Ramps: * 1 pair of aluminum access ramps (10.6 t/pair), 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Information: Iodpfxel Thwcj Ag Iotg * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 * Permissible gross weight of 20,000 kg technically possible * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available from approx. CW 44 / 2026

Stanje: novo, največja dovoljena obremenitev: 13.500 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, * TRA-Kombi 18.0: * 3-in-1 = for roll-off containers, skip containers, and as a low-loader ----Brakes: * TPMS (Tire Pressure Monitoring System) * EBS-E (Electronic Braking System) * Emergency release device for spring brake cylinders ----Axles: * 2 x 12 t Gigant axles ----Suspension: * Parabolic springs ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long * 40 mm drawbar eye with height adjustment device ----Electrics / Lighting: * LED tail lights * 15-pin power connector * TPMS, display option in the truck via EBS signal (no installation required on the truck side) Iedjl Thv Rspfx Ag Iotg ----General Attachments: * Toolbox made of powder-coated steel sheet, right side * Side underrun protection * Plastic quarter mudguards with spray protection * Storage box made of galvanized sheet metal for container nets, approx. 960 x 300 x 400/450 mm, right side * Plastic bumper buffer at rear * Mechanical drop-down supports at rear ----Load Area: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm raised) to guide roll containers * Steel floor with roller recesses in the bogie area * Possible to transport roll-off containers with a length of 5,500–7,000 mm * Pneumatic four-point clamp locking as well as mechanical locking angles at the front in the track, securing certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. volume of 10 m³ possible * Includes 8 removable tub stops for lateral centering of the tubs; front 4 stops plugged in with pivotable stop * Weld bead as anti-slip coating in the ramp area of the run-up incline ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning elements to securely fix the tubs * 4 lashing bars per side, cloverleaf design * 1 pair of 13.4 t UVV lashing rings at the front ----Ramps: * 1 pair of aluminium drive-on ramps (10.6 t / pair), 2,800 x 470 mm, suitable for rubber-wheeled and tracked vehicles (lockable storage compartment accessible from the rear) ----Information: * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 * Permissible gross weight up to 20,000 kg technically possible * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Available from approx. calendar week 44 / 2026

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Rear axle with steering function and electro-pneumatic steering lock ----Suspension: * Air suspension with lifting/lowering system and RtR valve ----Electrics / Lighting: * Tire pressure monitoring system (TPMS) * Smartboard operator panel mounted on the trailer with pressure sensors for total axle load display * 15-pin power connector * LED lighting system 12 / 24V * Removable LED beacon at rear left ----General attachments: * Side underrun protection Isdpfxspk D I As Ag Istg * Landing legs at the front and mechanical swing supports at rear of chassis * Straight steel mudguards * Spare wheel carrier mounted under chassis, right side ----Low-loader platform: * Gooseneck platform with 45° chamfered front corners and tool box at the front made of galvanized steel, W = 2,480 x H = 500 x L = 665 mm, with folding lid * 400 mm high aluminum side boards (RAL 9010 pure white) foldable and removable, along the sides of the gooseneck platform * Rear panel 150 mm high, plug-in * Rear slope on the gooseneck platform leading to low-bed, approx. 700 mm long * Gooseneck platform with 50 mm wooden planks; low-bed platform with 60 mm wooden planks * Tread plate over the axles ----Extensions: * 8 x mechanical folding extensions to a total width of 3 m (not on the rear slope, extension planks available with storage on gooseneck platform) * Mechanically adjustable warning panel sets, front and rear ----Load securing (Lashing package): * On the gooseneck platform: 2 x 6.3 t lashing rings per side and 3 x 5 t lashing bars per side on the outer frame * On the low-bed platform: 2 x 13.4 t lashing rings per side and 4 x 10 t lashing rings, swivel and lowerable, embedded in the outer frame * 2 x 6.4 t lashing eyes per side and 1 lashing ring at the rear, in the excavator-arm recess * 2 x container locks immediately after the step in the low-bed platform ----Excavator-arm recess: * Continuous from the end of the last rigid axle over the steering axle to the end cross member, with internal reinforcement profile, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Access ramps: * Mechanical one-piece, hot-dip galvanized hydraulic access ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * Quadruple control block for future retrofitting of hydraulically lateral shifting ramps by customer * The outer plank on the ramp is made of 50 mm hardwood * Climbing strips on the outer frame of the ramp and on the approach slope ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump output of 40 up to 120 liters/min in the truck) ----Loading dimensions: * Gooseneck platform loading area: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Loading height unladen: approx. 910 mm (incl. 860 mm approach slope) ----Fifth wheel height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractor units) ----Paint/Finish: * Chassis, access ramps, rear folding supports, and extension brackets are hot-dip galvanized * Axles, landing legs, and air reservoirs are painted in a shade of black * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale reserved * Sample images may show equipment not included in the offered vehicle ----Delivery time: * Available from week 38/2026

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profile 30.0: * EBS brake system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical axle compensation at rear * Side underrun protection * Pivoting supports at the rear on chassis frame * Mechanically adjustable warning sign packages front and rear Itsdpfjl Th Adjx Ag Isg * Front closed plastic mudguards and rear straight galvanized steel skirts, each with splash protection * Reflective contour tape on sides and rear * Fold-down (hot-dip galvanized) lid for toolbox on the turntable platform * Multi-voltage system * LED tail lights * Removable rotating beacon at rear * Drawbar with 40 mm draw eye and height adjustment via tension spring & turnbuckle * 15-pin electrical connector * 4 stake pockets on each side (stakes not included), with simultaneous lashing facility * Load securing package (La-Si-Paket) comprising: 2 lashing eyes (6.4 t) front left & right on main frame of turntable platform, 5 pairs of UVV-compliant lashing rings, swiveling and lowerable, loadable in all directions and recessed into outer frame - in the corners rated to 13.4 t, otherwise 10 t * 6 pairs of mechanical folding outriggers for 3 m total width (not in rear inclined section) * Extension boards stowed in the center of the loading area * Excavator arm rest over rear axle up to end crossmember, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the sides of the excavator arm rest) * Hydraulic one-piece ramps (approx. 3,000 x 720 mm) * 4-way control block for future retrofitting of hydraulic ramp shift * Mechanical lateral ramp shift * Loading area above turntable: approx. 1,960 x 2,520 mm * Unloaded loading height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unloaded loading height approx. 910 mm (incl. 860 mm approach slope) * Chassis, turntable, drawbar, and ramps hot-dip galvanized * Axles, springs, air tank, etc. painted in black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * --Permissible gross weight of 30,000 kg technically possible-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.660 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 600 mm, Leto izdelave: 2026, * KA-TA-R 14.4: * Wabco EBS (electronic braking system) Itedpfx Agox Hm Rce Ieg * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem compensation unit * Height-adjustable drawbar, approx. 300 mm, with 40 mm flange towing ring * Jost mechanical support winch at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted front right on the chassis * 15-pin electrical connector * LED tail lights 12/24 V * Bolt-on underrun guard * Plastic quarter mudguards * Net hooks located at the central locking bearing and 2 on the front wall * Chassis made of high-tensile steel * Steel three-way tipper body with reinforced "Strong" side walls (continuous upper side walls, reinforced with internal tube, no central stanchions, foldable with side wall spring lifter) * Bolt-on rear stanchions * Combination steel double-wing rear door, asymmetrical split, can swivel and be locked at 270°, not foldable, with additional pendulum frame for automatic tailgate opening when tipping, locking via galvanized rotary bolt lock at the rear and central locking. Deactivation function for automatic tailgate operation when reverse tipping with open door wing * 1 x 5 t lashing ring in each corner and 4 x 3 t lashing points recessed into the outer frame on each side * 4 mm high-tensile steel floor plate * Rear mounting rail for loading ramps * Reinforced body with load securing certificate * 1 pair of aluminum loading ramps, approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tired & tracked vehicles * Lockable rear storage compartment recessed below the loading area in the chassis for the ramps * Drawbar, underrun guard, rear stanchion, and rear folding supports hot-dip galvanized * Axles, springs, air tanks, and support winch painted in a black finish * Tires: 358/55 R 19.5 * Side wall coating in a RAL color of your choice (no custom or metallic finishes). Color can be changed up to approx. 6 weeks before completion. * Subject to errors and prior sale. * Available immediately from week 29/2026 * Sample images

Stanje: novo, največja dovoljena obremenitev: 10.660 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 600 mm, Leto izdelave: 2026, * KA-TA-R 14.4: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display capability in the truck via EBS signal – no truck-side installation required * Drum brakes * 2 x 7 t Gigant axles * Parabolic leaf springs with tandem compensating aggregate * Drawbar height adjustable by approx. 300 mm with 40 mm flange towing eye Ijdpfsx Hm Riox Ag Istg * Jost mechanical landing gear at the front * Two mechanical foldable supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted front-right on chassis * 15-pin power connector * LED rear lights 12/24 V * Bolt-on side underrun protection * Plastic quarter mudguards * Tie-down hooks located at central locking mounts, plus 2 on the front wall * Chassis made of fine grain steel * Steel platform – 3-way tipper body with reinforced strong side walls (continuous upper side walls with internal tube reinforcement – without intermediate posts, side walls foldable with drop side spring assist) * Rear corner posts bolted * Combination steel wing-door rear wall – dual-wing asymmetrical, can be swung and locked at 270°, not foldable, with additional swinging frame for automatic rear wall opening during tipping operation, locking via galvanised turning rod lock at the rear and central locking, deactivation function for automatic rear wall operation when tipping backwards with open door * Four 5 t lashing points in the corners, and four 3 t lashing rings recessed in the outer frame on each side * 4 mm steel floor made of fine grain steel * Mounting rail at rear for loading ramps * Reinforced body with cargo lashing certificate * 1 pair of aluminium loading ramps, approx. 3,570 x 410 mm (load capacity 10 t/pair) suitable for rubber-tyred & tracked vehicles * Lockable storage compartment at rear under load area recessed in chassis for the ramps * Drawbar, underrun protection, rear corner posts, and rear foldable supports hot-dip galvanized * Axles, springs, air tank and landing gear painted in black * Tyres: 358/55 R 19.5 * Drop sides painted in desired RAL color (no special or metallic finishes) – can be changed up to approx. 6 weeks before completion * Subject to errors and prior sale * Available immediately from calendar week 29/2026 * Example images

Stanje: novo, največja dovoljena obremenitev: 16.500 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal ETÜ-TAR 21 Tandem - Low Loader | Drive-over Platform Trailer Ref. for enquiries: 11630 Vehicle available immediately from stock in Alsdorf New vehicle inc. COC * Gross weight: 21 t, Payload: 16.5 t, hot-dip galvanized chassis * Platform version with 400 mm high front wall, ramp securing via ramp holding rods and diagonal bracing * Version with gross weight 21 t, reinforced frame and axles, axle spacing 1,810 mm * Floor height approx. 910 mm loaded / approx. 940 mm unloaded * 7 m loading area with 400 mm high front wall * Extended ramps: 3 m one-piece hot-dip galvanized ramps with galvanized grating * Ramp lift with vertically standing, adjustable springs for easy single-person operation * Load securing package: * 4 UVV folding lashing brackets (LC 8,000 daN) mounted in the existing hole pattern in the 45° outer frame, positioned approx. 1 m from front/rear crossmember * 10 UVV retractable lashing brackets (LC 3,000 daN) recessed in the existing hole pattern in the outer frame * 2 UVV lashing rings each at front and rear, recessed in crossmember, LC 10,000 daN * Additional lashing options via holes (Ø 50 mm, LC 1,200 daN) in the front and end crossmember Itsdpfx Aoyvxg Usg Ieg * Preparation for retrofitting container locks (container locks available at extra cost) * Softwood floor, 50 mm thick * Air suspension, Gigant axles incl. EBS 2S/2M, raising and lowering * 235/75R 17.5 (twin tyres, 8x) with tyre pressure monitoring sensor * Plastic toolbox in front of the front wall, right-hand side in direction of travel * LED lighting system * 7-pin socket at rear, prepared for overlength lighting with tail light (58 R) and ground * 2 LED reversing lights at rear * Flashing side marker lights * Oversize warning panel * 1 removable all-round LED beacon incl. bracket and installation * Folding supports at rear, front support leg with geared winding mechanism ---- Lease purchase example from our partner MMV Leasing: €665/month net for 60 months term with no down payment and €0 final instalment Other terms with/without down payment/final value possible! We are Müller-Mitteltal authorised dealer ----* Our business hours * Monday - Thursday: 08:00 - 17:00 * Friday: 08:00 - 15:00 * Outside business hours available by appointment * We speak German, English, Russian, Polish, French * WhatsApp

Stanje: novo, največja dovoljena obremenitev: 9.070 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.010 mm, višina nakladalnega prostora: 325 mm, Leto izdelave: 2026, * ETS-TA-B 11,9: * Wabco EBS (elektronski sistem kočenja) * RDÜ (nadzor pritiska u gumama) * Bubanj kočnice, 2 x 5,5 t Gigant osovine * Parabolične opruge sa izjednačivačem opterećenja * Vučno vratilo podesivo po visini oko 300 mm * BPW podupirač * Mehaničke zadnje noge za podršku * Plastična kutija za alat napred desno na čeonoj stranici * Bočna zaštita od podletanja * LED rasveta * Pod od 50 mm mekog, četinjastog drveta * U uglovima ispred čeone stranice i završnog nosača po 1 x 6,3 t hvatište za vezivanje, kao i po 2 UVV prstena za vezivanje po 6,3 t ugrađena sa strane u spoljašnji ram * Jednodelne mehaničke rampe od rešetki sa oprugom za rad jednom osobom, dimenzije oko 2.350 x 870 mm (unutrašnje rastojanje 20 mm, rampe nisu pomične) Itodpfxjwyhzpe Ag Ieg * Čeona stranica, bočne stranice, blatobrani i vučno vratilo toplo pocinkovani * Osovine, opruge, vazdušni rezervoar, prednji podupirač obojeni u crno * Novo vozilo sa punom garancijom proizvođača * Greške i međuprodaja zadržani * Dostupno od oko 35. nedelje 2026.

Stanje: novo, največja dovoljena obremenitev: 13.600 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2026, * KA-TA-RT 18.0: ----Braking System: * EBS (electronic braking system) Iedpevin T Sjfx Ag Istg * Emergency release device for spring-loaded cylinders * Drum brakes ----Suspension: * Air suspension with lifting and lowering system, including RtR valve and manual lowering for loading operations ----Drawbar / Flange Drawbar Eye: * Drawbar with positive-locking height adjustment * 50 mm flange drawbar eye ----Electrics / Lighting: * 15-pin 24 V connector * LED tail lights 12 / 24 V integrated in underrun protection ----General Attachments: * Landing gear at the front * Fold-out support legs at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * Plastic quarter mudguards ----Tipper Body: * Steel 3-way tipper body made of fine-grain steel with high M-Strong side walls and reinforced 180 bar tipping cylinder * Fixed front wall, smooth sheet steel * Hardwood pad for excavator bucket bolted to front wall * Continuous, folding drop sides without central stanchion, with sideboard spring assist and manual central locking system * Screwed-in rear stanchions * Combination steel swing doors, asymmetrical 2-leaf rear wall, can be swung and locked at 270°, not foldable, with additional swinging frame for automatic rear wall opening during tipping, locking via galvanized rotary bar lock and central locking system, deactivation function for automatic rear wall opening when tipping reverse with open swing doors * 4 mm steel floor plate * Two-step entry left front * Rear mounting rail for loading ramps ----Load Securing: * 1 x 7 t lashing ring in each corner * 4 x 3 t lashing rings recessed into the outer frame on each side ----Loading Ramps: * Integrally mounted ramp storage at the rear of the chassis * 1 pair of aluminum loading ramps (10 t / pair) approx. 3,570 x 410 mm, suitable for rubber-tired and tracked vehicles ----Paintwork: * Chassis, drawbar, rear stanchions, front wall, tipping platform, underrun protection, rear folding supports hot-dip galvanized * Sideboard paintwork in RAL custom color (with exceptions for special or metallic paintwork); can be changed up to approx. 6 weeks prior to delivery * Axles, air tanks, flange drawbar eye, front landing gear painted in black ----Information: * --Load securing certificate according to EN 12642 XL? * Subject to errors and prior sale ----Delivery Time: * Available from approx. CW 45 / 2026

Stanje: novo, največja dovoljena obremenitev: 13.600 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2026, * KA-TA-RT 18.0: ----Brake: * EBS (Electronic Braking System) * Emergency release for spring brake cylinders * Drum brakes ----Suspension: * Air suspension with lifting and lowering device, including Ride-Through-Release (RtR) valve and manual lowering function for loading ----Drawbar / Flanged Drawbar Eye: * Drawbar with positive-locking height adjustment * 50 mm flanged drawbar eye ----Electrics / Lighting: * 15-pin 24 V connector * LED tail lights 12 / 24 V fitted in underrun protection ----General Attachments: * Support winch at front * Fold-away rear support legs on the outside * Plastic toolbox approx. 750 x 350 x 300 mm, mounted on right side * Plastic quarter mudguards ----Tipping Body: * Steel pallet – 3-way tipper body made of high-tensile fine grain steel with high M-Strong side panels and reinforced 180 bar tipping cylinder * Fixed front wall made of smooth sheet steel * Hardwood strip for excavator bucket screwed onto front wall * Continuous side panels – fold-down without center pillar, with sideboard spring-assist lifters and swinging function via manual central locking * Bolt-on rear stanchions * Combination steel swing doors at rear, 2-leaf, asymmetrically split, able to swing open 270° and lockable (not foldable), including additional swinging frame for automatic rear door opening when tipping; locking by galvanized rotating bar lock and central locking, deactivation function for automatic rear door opening when tipping backwards with opened swing doors * 4 mm steel floor plate * Two-step access on the left front * Rear ramp track for loading ramps ----Load Securing: * One 7 t lashing ring in each corner * Four 3 t lashing eyes recessed in the outer frame on each side ----Loading Ramps: * Recessed ramp compartment at rear of chassis * 1 pair aluminium loading ramps (10 t/pair), approx. 3,570 x 410 mm, suitable for rubber-tired and tracked vehicles Itsdovin Ucspfx Ag Iog ----Paintwork: * Chassis, drawbar, rear stanchions, front wall, tipping platform, underrun protection, and rear supports hot-dip galvanized * Sideboards painted in any desired RAL colour (excluding special or metallic paints), can be changed up to approx. 6 weeks before completion * Axles, air tanks, flanged drawbar eye, and front support winch painted in black ----Info: * --Load securing certificate according to EN 12642 XL? * Errors and intermediate sale reserved ----Delivery Time: * Available from approx. CW 45 / 2026

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 09/1993, Leto izdelave: 1993, Oprema: ABS, = Additional Options and Accessories = - Electronic Braking System (EBS) = Notes = Müller-Mitteltal Low Loader 2-axle low-bed trailer ZSA Loading ramps Iodpfx Agext Rw Rj Istg IDNR 892 Transaction We look forward to advising you. Contract signing or vehicle collection can take place at our dealership. Please arrange an appointment. If you are unable to come to our dealership, we offer you the complete processing via phone/email/WhatsApp/fax. Upon request, we can deliver your new vehicle directly to your door. This means: best price, maximum security, and convenience when handing over the vehicle. We are also happy to take your used vehicle as trade-in. We offer the option of a digital vehicle appraisal based on your vehicle photos, even without visiting our dealership. Our specialized purchasing team guarantees you the highest price. Upon request, we can deliver your new 'used' vehicle nationwide right to your doorstep and collect your trade-in for financing or leasing. Immediate approval and settlement of outstanding loans. Your specialist partner for passenger cars, vans, commercial vehicles, and construction equipment ITC GmbH & Co KG Siemensstraße 7 32312 Lübbecke (industrial area) Always over 400 vehicles in stock. The information provided in advertisements, online, price tags, and images are non-binding descriptions and do not constitute guaranteed features. The seller assumes no liability/warranty for typographical or data transmission errors. Listed equipment may need to be checked separately. The offer is generally without new MOT; we are happy to provide you with an offer from our partner workshop. Subject to errors and prior sale. = Further Information = Unladen weight: 4,600 kg Payload: 13,400 kg Gross weight: 18,000 kg Sales price: €6,500, US$7,658

Stanje: rabljeno, največja dovoljena obremenitev: 8.650 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 07/2017, naslednji pregled (TÜV): 05/2026, dolžina tovornega prostora: 6.250 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, Dodatne informacije 400 mm zložljive stranske stranice - Dvižni mehanizem za stranice s vzmetjo - Snemljiva zadnja stena - Velik komplet za pritrjevanje tovora - Perforirana letva na tovornem prostoru - Sprednja podporna noga nastavljiva po višini - Zadnje podporne noge zložljive Iedpfxjy Hn D Rj Ag Istg - Plastična orodjarna skrinja - BPW osi - Vzmetne rampe z rešetko

Stanje: rabljeno, lastna masa: 3.210 kg, največja dovoljena obremenitev: 8.690 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 05/2021, naslednji pregled (TÜV): 06/2026, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.430 mm, višina nakladalnega prostora: 500 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R17.5, Leto izdelave: 2021, Oprema: ABS, Nemško vozilo MASTERLINE Müller-Mitteltal KA-TA-R 11,9 trosmerni kiper sa rampama ispod utovarene Godina prve registracije: 05/2021 pocinkovan Dozvoljena ukupna masa: 11.900 kg Sopstvena masa: 3.210 kg Nosivost: 8.690 kg Dimenzije pneumatika: 235/75 R 17,5 Tandem osovina manja od 1 m Vučna ruda je neprekidno podesiva po visini, toplo pocinkovana, vučna kuka 40 mm Ram pocinkovan BPW osovine Visina poda: 0,93 m Dodatne usluge dostupne! Izvozne tablice (crvene / 30 dana) Nemačka Kratkoročne tablice (žute / 5 dana) Nemačka Moguća organizacija austrijskih prevoznih tablica Isporuka vozila (uz nadoknadu) Podaci dati na internetu su nezahtevne informacije. Ne predstavljaju zagarantovana svojstva. Iedpoyxbgcefx Ag Iotg Prodavac ne preuzima odgovornost za greške, tipografske greške i greške u prenosu podataka. Prodaja uz mogućnost prethodne prodaje. Prodaja isključivo privrednim subjektima. Važe isključivo naši Opšti uslovi poslovanja.

Stanje: rabljeno, lastna masa: 3.210 kg, največja dovoljena obremenitev: 8.690 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 05/2021, naslednji pregled (TÜV): 06/2026, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.430 mm, višina nakladalnega prostora: 500 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R17.5, Leto izdelave: 2021, Oprema: ABS, Nemško vozilo MASTERLINE Müller-Mitteltal KA-TA-R 11,9 trosmerni kiper sa rampama ispod utovarene Godina prve registracije: 05/2021 pocinkovan Dozvoljena ukupna masa: 11.900 kg Sopstvena masa: 3.210 kg Nosivost: 8.690 kg Dimenzije pneumatika: 235/75 R 17,5 Tandem osovina manja od 1 m Vučna ruda je neprekidno podesiva po visini, toplo pocinkovana, vučna kuka 40 mm Ram pocinkovan BPW osovine Visina poda: 0,93 m Dodatne usluge dostupne! Izvozne tablice (crvene / 30 dana) Nemačka Iedpeyw N Npofx Ag Ijtg Kratkoročne tablice (žute / 5 dana) Nemačka Moguća organizacija austrijskih prevoznih tablica Isporuka vozila (uz nadoknadu) Podaci dati na internetu su nezahtevne informacije. Ne predstavljaju zagarantovana svojstva. Prodavac ne preuzima odgovornost za greške, tipografske greške i greške u prenosu podataka. Prodaja uz mogućnost prethodne prodaje. Prodaja isključivo privrednim subjektima. Važe isključivo naši Opšti uslovi poslovanja.

Stanje: novo, največja dovoljena obremenitev: 30.080 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – without truck-side installation * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning panel packages front & rear * SmartBord infotool installed with pressure sensors for total axle load display per axle group * Reflective contour tape on the sides and rear * LED rotating beacon (removable) at the rear * 15-pin power connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front closed single plastic mudguards * Straight rear steel mudflaps, each with spray suppression * Side underrun protection * Superstructure in front of the bogie platform approx. 520 mm with 45° corners and 3 storage compartments including lockable folding lids (folding lids opening to the rear) * Chassis made from high-strength fine-grained steel * Floor over the bogie platform made of 50 mm softwood, and 60 mm softwood in the low loader platform * Outer planks of the drive-on ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing eyes 6.4 t front left and right on the main frame of the bogie platform, 1 pair each of 13.4 t lashing rings at the front and rear outer frame, 1 pair each of 10 t lashing rings, swiveling and lowerable, loadable in all directions and recessed in the outer frame, 5 t lashing rings bolted to the outer frame of the wheel recesses (2 at the front recess, 1 at the rear), 2 pairs of 6.4 t lashing rings on the excavator stick holder * 11 pairs of folding outriggers for a total width of 3 meters (not at the rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for the widening boards made of sheet steel, mounted transversely to the loading area in front of the first rear axle * Excavator stick holder above the rear axle up to the end of the approach slope approx. 2,300 x 740 x 190 mm * Two wheel recesses per side approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with retractable cover (storage for covers at the front on the bogie platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm * Hydraulic lateral ramp shift * Loading area over the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loading height loaded approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, bogie, folding outriggers, rear drop-down supports, and drive-on ramps galvanised * Axles, air tanks, and drawbar painted in black * Tires: 235/75R17.5 Itsdoxmpydspfx Ag Ieg * Vehicle is galvanised * New vehicle with manufacturer’s warranty * Errors and prior sale reserved * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 30.080 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning sign packages front & rear * SmartBord infotool installed with pressure sensors for displaying axle group loads * Reflective contour tape on the sides and rear * LED beacon (removable) at the rear Isdpfx Agexmpykj Iotg * 15-pin electrical connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front enclosed individual plastic mudguards * Rear straight steel mudflaps with spray suppression * Side underrun protection * Extension in front of the bogie platform approx. 520 mm with 45° corners and 3 storage compartments with lockable folding lids (folding lids open towards the rear) * Chassis made from high-strength fine-grain steel * Floor over bogie platform made of 50 mm softwood, and in the low-bed platform made of 60 mm softwood * Outer planks of the ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing eyes 6.4 t each at the front left and right on the main frame of the bogie platform; one pair of 13.4 t lashing rings at the front and rear sides of outer frame; one pair of 10 t lashing rings on each side foldable and lowerable, loadable in all directions, integrated into the side frame; 5 t bolted lashing rings on the outer frame of the wheel recesses (2 per front wheel recess, 1 per rear); 2 pairs of 6.4 t lashing rings at the excavator stick compartment * 11 pairs of fold-out outriggers for overall width of 3 m (not on the rear incline) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for width-extension planks, steel, mounted crosswise to the loading area in front of the first rear axle * Excavator stick compartment above the rear axle extending to the end of the ramp incline, approx. 2,300 x 740 x 190 mm * Two wheel recesses per side approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with retractable cover (storage for covers at the front on bogie platform) for transporting wheel loaders with wheelbase 3,100 – 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulic extendable tip, approx. 4,650 x 720 mm * Hydraulic sideward ramp displacement * Loading area above the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded deck height approx. 890 mm ± 20 mm (including 860 mm ramp incline) * Chassis, bogie, fold-out outriggers, rear supports, and access ramps fully hot-dip galvanized * Axles, air tanks, and drawbar painted in black shade * Tires: 235/75R17.5 * Vehicle is fully hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 38.620 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, T5 Profile 50.0: ----Brakes: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes Ijdpel Tihuefx Ag Ietg ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (ride height +30 mm when axle is lifted) * Last axle self-steering (lockable from the driver's cab for maneuvering purposes without the need for truck-side installation; additionally lockable via switch on trailer). Deactivate the lock before driving on public roads. * Forced lifting and lowering of the lift axle for maneuvering purposes (truck-side installation required), with speed-dependent control via EBS electronics ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: * Drawbar, 1,500 mm long with 50 mm towing eye and manual height adjustment ----Electrics / Lighting: * Smartboard as infotool with pressure sensors for total axle load display per axle group * Tire pressure monitoring with indication in the truck via EBS signal (no truck-side installation necessary) * LED lighting system 12/24 V * Removable rear LED beacon ----General Accessories: * Mechanical warning plate kit for 3 m total width * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm, mounted side left * Front axle with plastic mudguards, rear with galvanized steel mudguard skirts ----Low Loader Platform: * Front section of turntable platform with 45° angles and 3 storage compartments with lockable, rear-hinged covers * Shortening of the lowbed platform by 500 mm to 6,280 mm including extended step by 500 mm to the front * Rubber covering on folding frame, drive-on ramp and running surface of the low-loader platform * Bamboo wood between the longitudinal beams in front of the excavator arm rest ----Load Securing (LaSi Package): * 2 x 6.4 t lashing rings at front corners * 2 x 13.4 t UVV lashing points each at side front and rear corners * 5 x 10 t UVV lashing rings per side (pivoting and lowerable, loadable in all directions) * 4 stake pockets per side with additional 2 t lashing capability each * 1 x 16 t UVV lashing ring on the rear cross member ----Widening: * Extendable and foldable widening outriggers for 3 m total width (beam holders under chassis, right side) ----Excavator Arm Rest: * Continuous excavator arm rest with reinforcement profile from last axle to tow bar approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on sides of arm rest ----Ramps: * Hydraulic folding ramp with dual-line hydraulics and extendable tip piece approx. 4,650 x 720 mm including load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (required in case of hydraulic pump output on truck over 40 l/min up to max. 140 l/min) ----Loading Height: * Loaded: 890 mm +/- 20 mm via air suspension ----Platform Dimensions: * Platform over turntable: 2,600 + 390 x 2,520 mm * Lowbed platform: 6,280 + 500 x 2,520 mm incl. 860 mm inclines ----Paintwork: * Chassis, turntable, drawbar, widening consoles, and ramps hot-dip galvanized * Tow bar, axles, hydraulic axle supports, and air tanks painted in black ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available immediately*

Stanje: novo, največja dovoljena obremenitev: 38.620 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, T5 Profile 50.0: ----Braking System: * Wabco EBS (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (when lifted, ride height +30 mm) * Last axle is self-steering (lockable from the cab for maneuvering purposes without any installation on the truck side, and additionally via a switch on the trailer). The lock must be disengaged before driving on public roads. * Forced lifting and lowering of the lift axle for maneuvering (truck-side installation required), with speed-dependent control via the EBS electronics ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: Drawbar 1,500 mm long with 50 mm draw eye and manual height adjustment ----Electrics / Lighting: * Smartboard as an info tool with pressure sensors for axle load indication per axle group * Tire pressure monitoring with display in the truck via EBS signal (without truck-side installation) * LED lighting system 12/24 V * LED rotating beacon (removable), rear ----General Fittings: * Mechanical warning sign set for 3 m total width * Toolbox made of galvanized steel plate approx. 650 x 300 x 600 mm, mounted left side * Plastic fenders front axle and galvanized steel mudguards rear axle ----Low Loader Platform: * Front section of turntable platform with 45° corners and 3 stowage compartments with lockable folding lids (folding towards the rear) * Shortening of the low-bed platform by 500 mm to 6,280 mm including extended recess by 500 mm at the front * Rubber covering on the folding frame, approach ramp, and running surface of the low-loader platform * Bamboo wood between the longitudinal beams, in front of the excavator stick rest area ----Load Securing (LaSi Package): * 2 x 6.4 t lashing eyes in the front corners * 2 x 13.4 t UVV lashing points on each side in the front and rear corners * 5 x 10 t UVV lashing rings on each side (swivelable and lowerable, loadable in all directions) * 4 stake pockets per side with simultaneous 2 t lashing option * 1 x 16 t UVV lashing ring on the rear crossmember ----Width Extension: * Extendable and foldable width supports for 3 m total width (plank holder under the chassis, right side) ----Excavator Stick Rest: * Continuous excavator stick rest with reinforcement profile from last axle to end beam approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on the sides of the excavator stick rest ----Ramps: * Hydraulic folding ramp with dual-circuit hydraulics and folding tip approx. 4,650 x 720 mm, including load-holding valves and hydraulic side shift ----Rear Support: Isdpfx Aexptn Deg Ijtg * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (for hydraulic pump outputs on the truck over 40 l/min up to max. 140 l/min) ----Loading Height: * Loaded: 890 mm +/- 20 mm adjustable via air suspension ----Loading Area Dimensions: * Platform above turntable: 2,600 + 390 x 2,520 mm * Low-bed loading platform: 6,280 + 500 x 2,520 mm, incl. 860 mm approach ramp ----Paintwork: * Chassis, turntable, drawbar, width extension consoles, ramps hot-dip galvanized * Drawbar yoke, axles, hydraulic axle supports and air tanks painted in black ----Information: * New vehicle with manufacturer warranty * Subject to prior sale and errors ----Delivery Time: Available immediately*

Stanje: rabljeno, številka stroja/vozila: 110, lastna masa: 8.320 kg, največja dovoljena obremenitev: 31.680 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2008, dolžina tovornega prostora: 10.300 mm, širina tovornega prostora: 2.550 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 r17,5, medosna razdalja: 6.500 mm, barva: modra, Oprema: ABS, * Drum brake * 4 axles * Wheelbase 6,500 mm * Hydraulic ramp length 2,850 mm – width 650 mm * Loading edge height 920 mm * Extendable to 3 m Itsdpfelpav Usx Ag Isg Subject to errors and omissions

Stanje: rabljeno, največja dovoljena obremenitev: 4.500 kg, skupna masa: 6.500 kg, konfiguracija osi: 2 osi, prva registracija: 07/1979, naslednji pregled (TÜV): 04/2026, dolžina tovornega prostora: 4.000 mm, širina tovornega prostora: 1.900 mm, višina nakladalnega prostora: 380 mm, skupna širina: 2.500 mm, skupna višina: 3.000 mm, Leto izdelave: 1979,

Stanje: novo, največja dovoljena obremenitev: 8.750 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal KA-TA-R 11.9 Tandem Low-bed Three-way Tipper Trailer with Ramps Reference number for inquiries: 11612 * BRAND-NEW VEHICLE, available immediately, painted in RAL 9016 traffic white * Delivery to your site possible for an additional charge! * Gross weight: 11,900 kg, payload: 8,750 kg * Galvanized floor, 5m x 2.42m x 0.5m; side walls are pendulum-mounted, foldable, and removable; prepared for later fitting of side wall extensions * Bulkhead is hot-dip galvanized * Lockable compartment under the tipping bed for loading ramps * Includes access ramps, 3.31m, 8t pair * 4 UVV lashing rings LC 5000daN at front and rear * 8 lashing eyes LC 3000daN recessed and foldable in the tipper floor (centered) * Net hooks * Drawbar infinitely height-adjustable, hot-dip galvanized, tow eye 40mm * Frame galvanized * Tyres 235/75R 17.5, (4 units), BPW axles, parabolic springs * Tire pressure monitoring * EBS (Electronic Braking System) * LED lighting system for 12+24 volts * Side marker lights with indicator activation * Bolted, galvanized rear stanchions * Excavator bucket rest mounted on the bulkhead ---- Please request an offer from us. Additional equipment available on request. Financing from as little as €405 net/month over 72 months with no down payment and no final balloon payment. Offer provided by our financing partner "FM LeasingPartner". ---- Our business hours: Itedpfxeyl Ebps Ag Ijg Monday - Thursday: 08:00 - 17:00 Friday: 08:00 - 15:00 Appointments outside opening hours possible by arrangement. WhatsApp Leasing, financing, and trade-in available----